Vand W Series Multipurpose Power Line RFI Filter for Emission Control and High-Noise Industrial Environments UL Recognized CSA Certified VDE Approved 20A 3A, 6A, 10A V and W Series Specifications The V series and W series filters will protect equipment from malfunctions due to conducted interference coming into the equipment from the line, especially line-to-line noise and transients. They will also provide needed noise suppression to allow most equipment to meet FCC specifications for conducted emissions. Maximum leakage current, each line-to-ground @ 120 VAC 60 Hz: @ 250 VAC 50 Hz: V Series - offers an N = 3 ("T") line-to-ground impedance to common mode and an N = 5 ("Dbl. Pi") impedance for line-to-line differential mode interference. The filters are designed for susceptibility use when equipment impedance at RF frequencies is low. Operating frequency: W Series - provides an N = 4 ("Dbl. L") line-to-ground impedance for common mode and an N = 5 ("Dbl. Pi") impedance for line-to-line differential mode interference. The filters are designed for use when equipment impedance at RF frequencies is high. The two-stage construction provides excellent suppression at high frequency. V series and W series filters are also effective to control emissions in equipment using SCR and T2L circuits, for compliance with FCC Part 15, Subpart J, and EN55022, Level A, down to 150kHz. Electrical Schematics V Series 0.5 mA .82 mA Hipot rating (one minute): line-to-ground line-to-line 2250 VDC 1450 VDC 50/60 Hz Rated voltage: 120/250 VAC Rated current: @120 VAC 3VV/3VW 6VV/6VW 10VV/10VW 20VV/20VW @ 250 VAC 3A 6A 10A 20A 2.5A 5A 8A 16A Minimum insertion loss in dB: Line-to-ground in 50 ohm circuit Current Rating V Series 3A 6A 10A 20A W Series 3A 6A 10A 20A Frequency-MHz 2 5 10 .15 .5 1 15 15 15 15 27 27 27 30 38 28 38 41 47 47 47 49 55 55 55 60 13 18 18 18 25 30 30 30 20 34 34 34 45 40 40 40 65 65 65 65 20 30 55 55 55 46 50 50 50 36 48 48 48 30 65 65 65 65 65 57 57 57 63 47 47 47 Line-to-line in 50 ohm circuit W Series 3A, 6A, 10A V W 78 W Series 20A Resistor location for reference only. Current Rating V Series 3A 6A 10A 20A W Series 3A 6A 10A 20A Frequency-MHz 1 2 5 10 .15 .3 .5 25 40 25 25 25 54 25 25 65 65 65 65 65 65 65 65 63 65 63 63 60 65 60 60 25 30 25 25 40 54 25 25 65 65 65 65 65 65 65 65 65 65 65 65 62 60 65 65 20 30 52 60 52 52 50 57 50 50 50 55 50 50 55 55 50 50 35 38 45 45 35 38 45 45 Libertyville, IL (847) 680-7400 Series Vand W Case Styles Case Dimensions Metric shown in italics. Metric shown in italics. A (max) B (max) C (max) 3VV1, 3VW1 3.36 1.82 1.28 85.3 46.2 32.5 60.33 70.6 6VV1, 6VW1 3.86 98.0 2.08 52.8 1.53 38.9 2.938 74.63 3.34 84.8 10VV1,10VW1 3.86 98.0 2.08 52.8 1.53 38.9 2.938 74.63 3.34 84.8 20VV1, 20VW1 5.23 132.8 3.38 85.9 1.53 38.9 3.75 95.25 4.2 106.7 20VV6, 20VW6 5.34 135.64 3.38 85.9 1.53 38.9 3.76 95.5 4.2 106.7 20VW7 5.65 143.51 3.12 79.25 2.29 58.17 3A, 6A, 10A Part No. Typical dimensions .0 7 .07 x .16 Terminals: . 250 (5) Holes: Dia.(4) Slot: Mounting holes: .188 Dia.(2) 6.35 1.8 1.8 x 4.1 4.78 20VV1/ 20VW1 D .015 .38 2.375 E (max) 2.78 Ordering Information Consult your local Corcom sales representative for pricing. Typical dimensions Terminals: .250 (5) Holes: .07 Dia.(4) Slot: 6.35 1.8 .07 x .16 1.8 x 4.1 20VV6/ 20VW6 Available Part Numbers 3VV1 6VV1 10VV1 20VV1 20VV6 3VW1 6VW1 10VW1 20VW1 20VW6 20VW7 20VW7 Panel Cutout Terminals: No. 8-32 (5) Torque: 18 2 in.lb. Mounting slots: .250 x .156 (4) 6.35 3.96 20VW7 Libertyville, IL (847) 680-7400 V W 79