Libertyville, IL (847) 680-7400
V
W
78
VandWSeries
Multipurpose Power Line RFI Filter
for Emission Control and High-Noise
Industrial Environments
UL Recognized
CSA Certified
VDE Approved
Specifications
Maximum leakage current, each
line-to-ground @ 120 VAC 60 Hz:0.5 mA
@ 250 VAC 50 Hz:.82 mA
Hipot rating (one minute):
line-to-ground2250 VDC
line-to-line1450 VDC
Operating frequency:50/60 Hz
Rated voltage:120/250 VAC
Rated current:@120 VAC@ 250 VAC
3VV/3VW 3A2.5A
6VV/6VW 6A5A
10VV/10VW 10A8A
20VV/20VW 20A16A
Minimum insertion loss in dB:
Line-to-ground in 50 ohm circuit
CurrentFrequency–MHz
Rating.15.51 2 5102030
V Series
3A1527384755555048
6A1527284755555048
10A1527384755555048
20A1530414960463630
W Series
3A1325204565656563
6A1830344065655747
10A1830344065655747
20A1830344065655747
Line-to-line in 50 ohm circuit
CurrentFrequency–MHz
Rating.15.3.51 2 5102030
V Series
3A252565656360525050
6A405465656565605755
10A252565656360525050
20A252565656360525050
W Series
3A254065656562553535
6A305465656560553838
10A252565656565504545
20A252565656565504545
Resistor location for reference only.
W Series 3A, 6A, 10A
W Series 20A
3A, 6A, 10A
20A
V and W Series
The V series and W series filters will protect equipment
from malfunctions due to conducted interference coming
into the equipment from the line, especially line-to-line
noise and transients. They will also provide needed noise
suppression to allow most equipment to meet FCC
specifications for conducted emissions.
V Series– offers an N = 3 (“T”) line-to-ground
impedance to common mode and an N = 5 (“Dbl. Pi”)
impedance for line-to-line differential mode interference.
The filters are designed for susceptibility use when
equipment impedance at RF frequencies is low.
W Series– provides an N = 4 (“Dbl. L”) line-to-ground
impedance for common mode and an N = 5 (“Dbl. Pi”)
impedance for line-to-line differential mode interference.
The filters are designed for use when equipment
impedance at RF frequencies is high. The two-stage
construction provides excellent suppression at high
frequency.
V series and W series filters are also effective to control
emissions in equipment using SCR and T
2
Lcircuits, for
compliance with FCC Part 15, SubpartJ, and EN55022,
Level A, down to 150kHz.
Electrical Schematics
V Series
V
W
79
SeriesVandW
Case Dimensions
Metric shown in italics.ABCDE
± .015
Part No.(max)(max)(max)(max)
± .38
3VV1, 3VW13.361.821.282.3752.78
85.346.232.560.3370.6
6VV1, 6VW13.862.081.532.9383.34
98.052.838.974.6384.8
10VV1,10VW13.862.081.532.9383.34
98.052.838.974.6384.8
20VV1, 20VW15.233.381.533.754.2
132.885.938.995.25106.7
20VV6, 20VW65.343.381.533.764.2
135.6485.938.995.5106.7
20VW75.653.122.29
143.5179.2558.17
Ordering Information
Consult your local Corcom sales representative for pricing.
Case Styles
Metric shown in italics.
20VV1/20VW1
20VV6/20VW6
20VW7
Terminals: No. 8-32 (5) Mounting slots:
.250
6.35.156
3.96
x(4)
20VW7 Panel Cutout
3A, 6A, 10A
Libertyville, IL (847) 680-7400
Typical dimensions
Terminals:(5)Holes:Dia.(4) Slot:
.250
6.35.07
1.8.07 x .16
1.8 x 4.1
Torque: 18 ± 2 in.lb.
Typical dimensions
Terminals: (5) Holes: Dia.(4) Slot: Mounting holes: Dia.(2)
.250
6.35.07
1.8.188
4.78
.07 x .16
1.8 x 4.1
Available Part Numbers
3VV13VW1
6VV16VW1
10VV110VW1
20VV120VW1
20VV620VW6
20VW7
