Ultralow Distortion Differential ADC Driver ADA4937-1/ADA4937-2 Data Sheet FEATURES FUNCTIONAL BLOCK DIAGRAMS 13 -VS 14 -VS 16 -VS -FB 1 12 PD +IN 2 11 -OUT -IN 3 10 +OUT 9 VOCM 06591-001 +VS 8 +VS 7 +VS 6 +VS 5 +FB 4 Figure 1. ADA4937-1 19 -OUT1 20 PD1 22 -VS1 21 -VS1 24 +IN1 -IN1 1 18 +OUT1 +FB1 2 17 VOCM1 +VS1 3 16 -VS2 +VS1 4 15 -VS2 06591-002 +OUT2 12 VOCM2 11 +VS2 9 13 -OUT2 +VS2 10 14 PD2 +IN2 6 -IN2 7 -FB2 5 +FB2 8 ADC drivers Single-ended-to-differential converters IF and baseband gain blocks Differential buffers Line drivers 23 -FB1 ADA4937-2 APPLICATIONS Figure 2. ADA4937-2 -55 HD2, HD3, HD2, HD3, -60 GENERAL DESCRIPTION -65 The ADA4937-1/ADA4937-2 are fabricated using Analog Devices, Inc., proprietary silicon-germanium (SiGe), complementary bipolar process, enabling them to achieve very low levels of distortion with an input voltage noise of only 2.2 nV/Hz. The low dc offset and excellent dynamic performance of the ADA4937-1/ADA4937-2 make them well-suited for a wide variety of data acquisition and signal processing applications. -75 -80 -85 -90 -95 -100 -105 -110 -115 1 10 100 FREQUENCY (MHz) 06591-003 With the ADA4937-1/ADA4937-2, differential gain configurations are easily realized with a simple external feedback network of four resistors that determine the closed-loop gain of the amplifier. VS = 5.0V VS = 5.0V VS = 3.3V VS = 3.3V -70 DISTORTION (dBc) The ADA4937-1/ADA4937-2 are low noise, ultralow distortion, high speed differential amplifiers. They are an ideal choice for driving high performance ADCs with resolutions up to 16 bits from dc to 100 MHz. The adjustable level of the output common mode allows the ADA4937-1/ADA4937-2 to match the input of the ADC. The internal common-mode feedback loop also provides exceptional output balance as well as suppression of even-order harmonic distortion products. Rev. F 15 -VS ADA4937-1 Extremely low harmonic distortion (HD) -112 dBc HD2 at 10 MHz -84 dBc HD2 at 70 MHz -77 dBc HD2 at 100 MHz -102 dBc HD3 at 10 MHz -91 dBc HD3 at 70 MHz -84 dBc HD3 at 100 MHz Low input voltage noise: 2.2 nV/Hz High speed -3 dB bandwidth of 1.9 GHz, G = 1 Slew rate: 6000 V/s, 25% to 75% Fast overdrive recovery of 1 ns 0.5 mV typical offset voltage Externally adjustable gain Differential-to-differential or single-ended-to-differential operation Adjustable output common-mode voltage Single-supply operation: 3.3 V to 5 V Figure 3. Harmonic Distortion vs. Frequency The ADA4937-1/ADA4937-2 are available in a Pb-free, 3 mm x 3 mm, 16-lead LFCSP (ADA4937-1, single) or a Pb-free, 4 mm x 4 mm, 24-lead LFCSP (ADA4937-2, dual). The pinout has been optimized to facilitate PCB layout and minimize distortion. The ADA4937-1/ADA4937-2 are specified to operate over the automotive (-40C to +105C) temperature range and between 3.3 V and 5 V supplies. Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2007-2016 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com ADA4937-1/ADA4937-2 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Analyzing an Application Circuit ............................................ 18 Applications ....................................................................................... 1 Setting the Closed-Loop Gain .................................................. 18 General Description ......................................................................... 1 Estimating the Output Noise Voltage ...................................... 18 Functional Block Diagrams ............................................................. 1 Impact of Mismatches in the Feedback Networks ................. 19 Revision History ............................................................................... 2 Calculating the Input Impedance for an Application Circuit ....................................................................................................... 19 Specifications..................................................................................... 3 5 V Operation ............................................................................... 3 3.3 V Operation ............................................................................ 5 Absolute Maximum Ratings ............................................................ 7 Thermal Resistance ...................................................................... 7 ESD Caution .................................................................................. 7 Pin Configurations and Function Descriptions ........................... 8 Typical Performance Characteristics ............................................. 9 Test Circuits ..................................................................................... 16 Terminology .................................................................................... 17 Input Common-Mode Voltage Range in Single-Supply Applications ................................................................................ 20 Setting the Output Common-Mode Voltage .......................... 20 Power-Down Operation ............................................................ 20 Layout, Grounding, and Bypassing .............................................. 22 High Performance ADC Driving ................................................. 23 3.3 V Operation .......................................................................... 25 Outline Dimensions ....................................................................... 26 Ordering Guide .......................................................................... 26 Theory of Operation ...................................................................... 18 REVISION HISTORY 6/2016--Rev. E to Rev. F Updated Outline Dimensions ....................................................... 26 Changes to Ordering Guide .......................................................... 26 5/2015--Rev. D to Rev. E Changes to Table 6 ............................................................................ 7 Updated Outline Dimensions ....................................................... 26 Changes to Ordering Guide .......................................................... 26 8/2013--Rev. C to Rev. D Changes to Input Bias Current Parameter, Table 1 ...................... 3 Changes to Input Bias Current Parameter, Table 3 ...................... 5 Updated Outline Dimensions ....................................................... 26 3/2010--Rev. B to Rev. C Changes to Table 2, Power Supply Parameter ............................... 4 Changes to Table 4, Power Supply Parameter ............................... 6 Changes to Figure 43 ...................................................................... 15 Added the Power-Down Operation Section ............................... 20 10/2009--Rev. A to Rev. B Changes to General Description Section ...................................... 1 Changes to Table 1 ............................................................................ 3 Changes to Operating Temperature Range Parameter, Table 2.. 4 Changes to Table 3 ............................................................................ 5 Changes to Figure 4 .......................................................................... 7 Changes to Figure 5 and Figure 6 ....................................................8 Added EP Row to Table 7 and EP Row to Table 8 ........................8 Added Figure 46, Figure 47, and Figure 48; Renumbered Sequentially ..................................................................................... 15 Changes to Table 9.......................................................................... 18 Changes to Input Common-Mode Voltage Range in SingleSupply Applications Section.......................................................... 20 Changes to Ordering Guide .......................................................... 26 11/2007--Rev. 0 to Rev. A Added the ADA4937-2 ...................................................... Universal Changes to Features ..........................................................................1 Changes to Specifications .................................................................3 Changes to Figure 4 ...........................................................................7 Changes to Typical Performance Characteristics..........................9 Inserted Figure 44........................................................................... 15 Added the Terminating a Single-Ended Input Section ............. 19 Changes to Table 10 and Table 11 ................................................ 21 Changes to Layout, Grounding, and Bypassing Section ........... 22 Inserted Figure 59, Figure 60, and Figure 61 .............................. 22 Updated Outline Dimensions ....................................................... 26 Changes to Ordering Guide .......................................................... 26 5/2007--Revision 0: Initial Version Rev. F | Page 2 of 28 Data Sheet ADA4937-1/ADA4937-2 SPECIFICATIONS 5 V OPERATION TA = 25C, +VS = 5 V, -VS = 0 V, VOCM = +VS/2, RT = 61.9 , RG = RF = 200 , Gain (G) = +1, RL, dm = 1 k, unless otherwise noted. All specifications refer to single-ended input and differential outputs, unless otherwise noted. DIN to OUT Performance Table 1. Parameter DYNAMIC PERFORMANCE -3 dB Small Signal Bandwidth Bandwidth for 0.1 dB Flatness Large Signal Bandwidth Slew Rate Settling Time Overdrive Recovery Time NOISE/HARMONIC PERFORMANCE Second Harmonic Third Harmonic IMD Voltage Noise (RTI) Input Current Noise Noise Figure Crosstalk (ADA4937-2) INPUT CHARACTERISTICS Offset Voltage Test Conditions/Comments Min VOUT, dm = 0.1 V p-p VOUT, dm = 0.1 V p-p VOUT, dm = 2 V p-p VOUT, dm = 2 V p-p; 25% to 75% VOUT, dm = 2 V p-p VIN = 0 V to 1.5 V step; G = 3.16 See Figure 51 for distortion test circuit VOUT, dm = 2 V p-p; 10 MHz VOUT, dm = 2 V p-p; 70 MHz VOUT, dm = 2 V p-p; 100 MHz VOUT, dm = 2 V p-p; 10 MHz VOUT, dm = 2 V p-p; 70 MHz VOUT, dm = 2 V p-p; 100 MHz f1 = 70 MHz; f2 = 70.1 MHz; VOUT, dm = 2 V p-p f = 100 kHz f = 100 kHz G = 4; RT = 136 ; RF = 200 ; RG = 37 ; f = 100 MHz f = 100 MHz VOS, dm = VOUT, dm/2; VDIN+ = VDIN- = 2.5 V TMIN to TMAX variation Input Bias Current -2.5 -50 TMIN to TMAX variation Input Offset Current Input Resistance Input Capacitance Input Common-Mode Voltage CMRR OUTPUT CHARACTERISTICS Output Voltage Swing Linear Output Current Output Balance Error -2 Differential Common mode VOUT, dm/VIN, cm; VIN, cm = 1 V -69 Maximum VOUT; single-ended output; RF = RG = 10 k Per amplifier; RL, dm = 20 ; f = 10 MHz VOUT, cm/VOUT, dm; VOUT, dm = 1 V; f = 10 MHz; see Figure 50 for test circuit 0.9 Rev. F | Page 3 of 28 Typ Max Unit 1900 200 1700 6000 7 <1 MHz MHz MHz V/s ns ns -112 -84 -77 -102 -91 -84 -91 2.2 4 15 -72 dBc dBc dBc dBc dBc dBc dBc nV/Hz pA/Hz dB dB 0.5 1 -30 0.01 +0.5 6 3 1 0.3 to 3.0 -80 +2.5 -10 +2 4.1 70 -61 mV V/C A A/C A M M pF V dB V mA dB ADA4937-1/ADA4937-2 Data Sheet VOCM to OUT Performance Table 2. Parameter VOCM DYNAMIC PERFORMANCE -3 dB Bandwidth Slew Rate Input Voltage Noise (RTI) VOCM INPUT CHARACTERISTICS Input Voltage Range Input Resistance Input Offset Voltage Input Bias Current VOCM CMRR Gain POWER SUPPLY Operating Range Quiescent Current per Amplifier Power Supply Rejection Ratio POWER-DOWN (PD) PD Input Voltage Turn-Off Time Turn-On Time PD Bias Current per Amplifier Enabled Powered Down Test Conditions/Comments Min 1.2 8 VOS, cm = VOUT, cm; VDIN+ = VDIN- = +VS/2 Enabled TMIN to TMAX variation Powered down VOUT, dm/VS; VS = 1 V Max 440 1150 7.5 VIN = 1.5 V to 3.5 V; 25% to 75% f = 100 kHz VOUT, dm/VOCM; VOCM = 1 V VOUT, cm/VOCM; VOCM = 1 V Typ -70 0.97 3.0 38.0 0.02 -70 Powered down Enabled 10 2 0.5 -75 0.98 39.5 17 0.3 -90 MHz V/s nV/Hz 3.8 12 7.1 1.00 5.25 42.0 0.5 1 2 1 200 PD = 5 V PD = 0 V 10 -300 OPERATING TEMPERATURE RANGE -40 Rev. F | Page 4 of 28 30 -200 Unit V k mV A dB V/V V mA A/C mA dB V V s ns 50 -150 A A +105 C Data Sheet ADA4937-1/ADA4937-2 3.3 V OPERATION TA = 25C, +VS = 3.3 V, -VS = 0 V, VOCM = +VS/2, RT = 61.9 , RG = RF = 200 , G = 1, RL, dm = 1 k, unless otherwise noted. All specifications refer to single-ended input and differential outputs, unless otherwise noted. DIN to OUT Performance Table 3. Parameter DYNAMIC PERFORMANCE -3 dB Small Signal Bandwidth Bandwidth for 0.1 dB Flatness Large Signal Bandwidth Slew Rate Settling Time Overdrive Recovery Time NOISE/HARMONIC PERFORMANCE Second Harmonic Third Harmonic IMD Voltage Noise (RTI) Input Current Noise Noise Figure Crosstalk (ADA4937-2) INPUT CHARACTERISTICS Offset Voltage Test Conditions/Comments VOUT, dm = 0.1 V p-p VOUT, dm = 0.1 V p-p VOUT, dm = 2 V p-p VOUT, dm = 2 V p-p; 25% to 75% VOUT, dm = 2 V p-p VIN = 0 V to 1.0 V step; G = 3.16 See Figure 51 for distortion test circuit VOUT, dm = 2 V p-p; 10 MHz VOUT, dm = 2 V p-p; 70 MHz VOUT, dm = 2 V p-p; 100 MHz VOUT, dm = 2 V p-p; 10 MHz VOUT, dm = 2 V p-p; 70 MHz VOUT, dm = 2 V p-p; 100 MHz f1 = 70 MHz; f2 = 70.1 MHz; VOUT, dm = 2 V p-p f = 100 kHz f = 100 kHz G = 4; RT = 136 ; RF = 200 ; RG = 37 ; f = 100 MHz f = 100 MHz VOS, dm = VOUT, dm/2; VDIN+ = VDIN- = +VS/2 TMIN to TMAX variation Input Bias Current Input Resistance Input Capacitance Input Common-Mode Voltage CMRR OUTPUT CHARACTERISTICS Output Voltage Swing Linear Output Current Output Balance Error Min -2.5 -50 TMIN to TMAX variation Differential Common mode VOUT, dm/VIN, cm; VIN, cm = 1 V -67 Maximum VOUT; single-ended output; RF = RG = 10 k Per amplifier; RL, dm = 20 ; f = 10 MHz VOUT, cm/VOUT, dm; VOUT, dm = 1 V; f = 10 MHz; see Figure 50 for test circuit 0.8 Rev. F | Page 5 of 28 Typ Max Unit 1800 200 1300 4000 7 <1 MHz MHz MHz V/s ns ns -113 -85 -77 -95 -77 -71 -87 2.2 4 15 -72 dBc dBc dBc dBc dBc dBc dBc nV/Hz pA/Hz dB dB 0.5 1 -30 0.01 6 3 1 0.3 to 1.2 -80 +2.5 -10 2.5 47 -61 mV V/C A A/C M M pF V dB V mA dB ADA4937-1/ADA4937-2 Data Sheet VOCM to OUT Performance Table 4. Parameter VOCM DYNAMIC PERFORMANCE -3 dB Bandwidth Slew Rate Input Voltage Noise (RTI) VOCM INPUT CHARACTERISTICS Input Voltage Range Input Resistance Input Offset Voltage Input Bias Current VOCM CMRR Gain POWER SUPPLY Operating Range Quiescent Current per Amplifier Power Supply Rejection Ratio POWER-DOWN (PD) PD Input Voltage Turn-Off Time Turn-On Time PD Bias Current per Amplifier Enabled Powered Down Test Conditions/Comments Min Typ 440 900 7.5 VIN = 0.9 V to 2.4 V; 25% to 75% f = 100 kHz 1.2 VOS, cm = VOUT, cm; VDIN+ = VDIN- = 1.67 V VOUT, dm/VOCM; VOCM = 1 V VOUT, cm/VOCM; VOCM = 1 V Enabled TMIN to TMAX variation Powered down VOUT, dm/VS; VS = 1 V Max -70 0.97 3.0 36 0.02 -70 Powered down Enabled MHz V/s nV/Hz 2.1 10 2 0.5 -75 0.98 38 17 0.2 -90 7.1 1.00 5.25 40 0.5 1 2 1 200 PD = 3.3 V PD = 0 V 10 -200 OPERATING TEMPERATURE RANGE -40 Rev. F | Page 6 of 28 20 -120 Unit V k mV A dB V/V V mA A/C mA dB V V s ns 30 -100 A A +105 C Data Sheet ADA4937-1/ADA4937-2 ABSOLUTE MAXIMUM RATINGS Rating 5.5 V See Figure 4 -65C to +125C -40C to +105C 300C 150C Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. THERMAL RESISTANCE JA is specified for the device (including exposed pad) soldered to a high thermal conductivity 2s2p circuit board, as described in EIA/JESD51-7. Table 6. Thermal Resistance Package Type 16-Lead LFCSP (Exposed Pad) 24-Lead LFCSP (Exposed Pad) JA 95 67 JC 12.6 8.78 Unit C/W C/W Maximum Power Dissipation The maximum safe power dissipation in the ADA4937-1/ ADA4937-2 packages is limited by the associated rise in junction temperature (TJ) on the die. At approximately 150C, which is the glass transition temperature, the plastic changes the properties. Even temporarily exceeding this temperature limit can change the stresses that the package exerts on the die, permanently shifting the parametric performance of the ADA4937-1/ ADA4937-2. Exceeding a junction temperature of 150C for an extended period can result in changes in the silicon devices, potentially causing failure. Airflow increases heat dissipation, effectively reducing JA. In addition, more metal directly in contact with the package leads/exposed pad from metal traces, through holes, ground, and power planes reduces JA. Figure 4 shows the maximum safe power dissipation in the package vs. the ambient temperature for the ADA4937-1 single 16-lead LFCSP (95C/W), and the ADA4937-2 dual 24-lead LFCSP (67C/W) on a JEDEC standard 4-layer board. 3.5 3.0 2.5 ADA4937-2 2.0 1.5 ADA4937-1 1.0 0.5 0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 AMBIENT TEMPERATURE (C) 06591-004 Parameter Supply Voltage Power Dissipation Storage Temperature Range Operating Temperature Range Lead Temperature (Soldering, 10 sec) Junction Temperature The power dissipated in the package (PD) is the sum of the quiescent power dissipation and the power dissipated in the package due to the load drive. The quiescent power is the voltage between the supply pins (VS) times the quiescent current (IS). The power dissipated due to the load drive depends upon the particular application. The power due to load drive is calculated by multiplying the load current by the associated voltage drop across the device. RMS voltages and currents must be used in these calculations. MAXIMUM POWER DISSIPATION (W) Table 5. Figure 4. Maximum Power Dissipation vs. Temperature, 4-Layer Board ESD CAUTION Rev. F | Page 7 of 28 ADA4937-1/ADA4937-2 Data Sheet 19 -OUT1 21 -VS1 20 PD1 22 -VS1 24 +IN1 23 -FB1 18 +OUT1 -IN1 1 12 PD +FB1 2 +VS1 3 +IN 2 ADA4937-1 11 -OUT -IN 3 TOP VIEW (Not to Scale) 10 +OUT +VS1 4 9 -FB2 5 2 3 4 +IN -IN +FB 5 to 8 9 10 11 12 13 to 16 EP +VS VOCM +OUT -OUT PD -VS +OUT2 12 VOCM2 11 +VS2 10 +VS2 9 13 -OUT2 Figure 6. ADA4937-2 Pin Configuration Table 7. ADA4937-1 Pin Function Descriptions Mnemonic -FB 14 PD2 NOTES 1. EXPOSED PADDLE. THE EXPOSED PAD IS NOT ELECTRICALLY CONNECTED TO THE DEVICE. IT IS TYPICALLY SOLDERED TO GROUND OR A POWER PLANE ON THE PCB THAT IS THERMALLY CONDUCTIVE. Figure 5. ADA4937-1 Pin Configuration Pin No. 1 TOP VIEW (Not to Scale) -IN2 7 NOTES 1. EXPOSED PADDLE. THE EXPOSED PAD IS NOT ELECTRICALLY CONNECTED TO THE DEVICE. IT IS TYPICALLY SOLDERED TO GROUND OR A POWER PLANE ON THE PCB THAT IS THERMALLY CONDUCTIVE. 16 -VS2 15 -VS2 +IN2 6 06591-005 +VS 7 VOCM +VS 8 +VS 5 +VS 6 +FB 4 17 VOCM1 ADA4937-2 +FB2 8 -FB 1 06591-006 13 -VS 14 -VS 16 -VS 15 -VS PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS Description Negative Output for Feedback Component Connection. Positive Input Summing Node. Negative Input Summing Node. Positive Output for Feedback Component Connection. Positive Supply Voltage. Output Common-Mode Voltage. Positive Output for Load Connection. Negative Output for Load Connection. Power-Down Pin. Negative Supply Voltage. Exposed Paddle. The exposed pad is not electrically connected to the device. It is typically soldered to ground or a power plane on the PCB that is thermally conductive. Table 8. ADA4937-2 Pin Function Descriptions Pin No. 1 2 3, 4 5 6 7 8 9, 10 11 12 13 14 15, 16 17 18 19 20 21, 22 23 24 EP Rev. F | Page 8 of 28 Mnemonic -IN1 +FB1 +VS1 -FB2 +IN2 -IN2 +FB2 +VS2 VOCM2 +OUT2 -OUT2 PD2 -VS2 VOCM1 +OUT1 -OUT1 PD1 -VS1 -FB1 +IN1 Description Negative Input Summing Node 1. Positive Output Feedback Pin 1. Positive Supply Voltage 1. Negative Output Feedback Pin 2. Positive Input Summing Node 2. Negative Input Summing Node 2. Positive Output Feedback Pin 2. Positive Supply Voltage 2. Output Common-Mode Voltage 2. Positive Output 2. Negative Output 2. Power-Down Pin 2. Negative Supply Voltage 2. Output Common-Mode Voltage 1. Positive Output 1. Negative Output 1. Power-Down Pin 1. Negative Supply Voltage 1. Negative Output Feedback Pin 1. Positive Input Summing Node 1. Exposed Paddle. The exposed pad is not electrically connected to the device. It is typically soldered to ground or a power plane on the PCB that is thermally conductive. Data Sheet ADA4937-1/ADA4937-2 TYPICAL PERFORMANCE CHARACTERISTICS TA = 25C, +VS = 5 V, -VS = 0 V, VOUT, dm = 2 V p-p, VOCM = +VS/2, RT = 61.9 , RG = RF = 200 , G = 1, RL, dm = 1 k, unless otherwise noted. Refer to Figure 49 for the test setup circuit. 6 0 -3 -6 -9 -12 1 10 100 1000 FREQUENCY (MHz) CLOSED-LOOP GAIN (dB) 1 10 100 1000 VS = 3.3V VS = 5.0V -6 -9 0 -3 -6 -9 -12 10 100 1000 FREQUENCY (MHz) -15 06591-008 1 100 1000 Figure 11. Large Signal Frequency Response for Various Supplies 6 +105C +25C -40C +105C +25C -40C 3 CLOSED-LOOP GAIN (dB) 3 10 FREQUENCY (MHz) Figure 8. Small Signal Frequency Response for Various Supplies, VOUT, dm = 100 mV p-p 6 1 06591-011 CLOSED-LOOP GAIN (dB) G = +1, RF = 200 G = +2, RF = 402 G = +5, RF = 402 3 -12 CLOSED-LOOP GAIN (dB) -12 6 VS = 5.0V -3 0 -3 -6 -9 0 -3 -6 -9 1 10 100 FREQUENCY (MHz) 1000 -12 06591-009 -12 -9 Figure 10. Large Signal Frequency Response for Various Gains 0 -15 -6 FREQUENCY (MHz) VS = 3.3V 3 -3 -15 Figure 7. Small Signal Frequency Response for Various Gains, VOUT, dm = 100 mV p-p 6 0 Figure 9. Small Signal Frequency Response for Various Temperatures, VOUT, dm = 100 mV p-p 1 10 100 FREQUENCY (MHz) 1000 06591-012 -15 G = +1, RF = 200 G = +2, RF = 402 G = +5, RF = 402 3 06591-076 NORMALIZED CLOSED-LOOP GAIN (dB) 3 06591-075 NORMALIZED CLOSED-LOOP GAIN (dB) 6 Figure 12. Large Signal Frequency Response for Various Temperatures Rev. F | Page 9 of 28 ADA4937-1/ADA4937-2 6 Data Sheet 6 RL = 1k RL = 100 RL = 200 3 CLOSED-LOOP GAIN (dB) 0 -3 100 1000 -9 100 1000 Figure 16. Large Signal Frequency Response for Various Loads 6 3 0 -3 -6 -9 VS = 3.3V, G = +1, VS = 3.3V, G = +2, VS = 3.3V, G = +5, 1 10 RF = 200 RF = 402 RF = 402 100 1000 FREQUENCY (MHz) 0 -3 -6 -9 -12 -15 06591-077 -12 3 VS = 3.3V, G = +1, VS = 3.3V, G = +2, VS = 3.3V, G = +5, 1 RF = 200 RF = 402 RF = 402 10 100 1000 FREQUENCY (MHz) 06591-079 NORMALIZED CLOSED-LOOP GAIN (dB) 6 NORMALIZED CLOSED-LOOP GAIN (dB) 10 FREQUENCY (MHz) Figure 13. Small Signal Frequency Response for Various Loads, VOUT, dm = 100 mV p-p Figure 17. Large Signal Frequency Response for Various Gains, VS = 3.3 V Figure 14. Small Signal Frequency Response for Various Gains, VS = 3.3 V, VOUT, dm = 100 mV p-p 6 NORMALIZED CLOSED-LOOP GAIN (dB) 6 3 0 -3 -6 -9 -12 G = +1, RF = 348 G = +2, RF = 348 G = +5, RF = 348 1 10 100 1000 FREQUENCY (MHz) Figure 15. Small Signal Frequency Response for Various Gains, VOUT, dm = 100 mV p-p, RF = 348 3 0 -3 -6 -9 -12 -15 06591-078 NORMALIZED CLOSED-LOOP GAIN (dB) 1 06591-016 10 06591-013 1 FREQUENCY (MHz) -15 -3 -6 -6 -15 0 G = +1, RF = 348 G = +2, RF = 348 G = +5, RF = 348 1 10 100 FREQUENCY (MHz) 1000 06591-080 CLOSED-LOOP GAIN (dB) 3 -9 RL = 1k RL = 100 RL = 200 Figure 18. Large Signal Frequency Response for Various Gains, RF = 348 Rev. F | Page 10 of 28 Data Sheet 3 -50 VOCM = 1.0V VOCM = 2.5V VOCM = 3.9V 0 VOCM CLOSED-LOOP GAIN (dB) ADA4937-1/ADA4937-2 HD2, HD3, HD2, HD3, -60 G G G G = +1, = +1, = +2, = +2, RF = 200 RF = 200 RF = 402 RF = 402 DISTORTION (dBc) -70 -3 -6 -80 -90 -100 -9 1 10 100 1000 FREQUENCY (MHz) -120 06591-019 HD2, HD3, HD2, HD3, -60 RL = 1k RL = 1k RL = 200 RL = 200 DISTORTION (dBc) -70 -80 -90 -100 1 10 100 1000 -120 -55 HD2, HD3, HD2, HD3, -60 -65 1 10 06591-023 -110 06591-020 GAIN (dB) -50 100 FREQUENCY (MHz) Figure 20. 0.1 dB Flatness Response for Various Loads Figure 23. Harmonic Distortion vs. Frequency and Load -50 VS = 5.0V VS = 5.0V VS = 3.3V VS = 3.3V -60 -70 HD2, HD3, HD2, HD3, VS = 3.3V VS = 3.3V VS = 5.0V VS = 5.0V -70 -75 DISTORTION (dBc) DISTORTION (dBc) 100 Figure 22. Harmonic Distortion vs. Frequency and Gain RL = 1k, ADA4937-1 RL = 100, ADA4937-1 RL = 1k, ADA4937-2 RL = 100, ADA4937-2 FREQUENCY (MHz) -80 -85 -90 -95 -80 -90 -100 -110 -100 -105 -120 1 10 100 FREQUENCY (MHz) 06591-021 -110 -115 10 FREQUENCY (MHz) Figure 19. Small Signal Frequency Response for Various VOCM 1.5 1.4 1.3 1.2 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 -0.1 -0.2 -0.3 -0.4 -0.5 1 Figure 21. Harmonic Distortion vs. Frequency and Supply Voltage -130 -1 0 1 2 3 4 5 6 VOUT (V) Figure 24. Harmonic Distortion vs. VOUT and Supply Voltage Rev. F | Page 11 of 28 7 06591-024 -12 06591-022 -110 ADA4937-1/ADA4937-2 -30 HD2, HD3, HD2, HD3, -40 DISTORTION (dBc) -50 Data Sheet 0 f = 10MHz f = 10MHz f = 75MHz f = 75MHz -20 DISTORTION (dBc) -60 -70 -80 -90 -40 -60 -80 -100 -100 1.5 2.0 2.5 3.0 3.5 4.0 VOCM (V) -120 69.4 06591-025 -120 1.0 HD2, HD3, HD2, HD3, -50 69.8 70.0 70.2 70.4 70.6 FREQUENCY (MHz) Figure 25. Harmonic Distortion vs. VOCM and Frequency -40 69.6 06591-028 -110 Figure 28. 70 MHz Intermodulation Distortion -30 f = 30MHz f = 30MHz f = 75MHz f = 75MHz RL = 200 DISTORTION (dBc) -40 CMRR (dB) -60 -70 -50 -80 -60 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 VOCM (V) -70 06591-026 -100 1.1 1 10 Figure 26. Harmonic Distortion vs. VOCM and Frequency, VS = 3.3 V -50 HD2, HD3, HD2, HD3, -60 1000 Figure 29. CMRR vs. Frequency -10 1V p-p 1V p-p 2V p-p 2V p-p RL = 200 -20 OUTPUT BALANCE (dB) -70 -80 -90 -100 -110 -30 -40 -50 -130 1 10 100 FREQUENCY (MHz) Figure 27. Harmonic Distortion vs. Frequency and VOUT, VS = 3.3 V -60 1 10 100 FREQUENCY (MHz) Figure 30. Output Balance vs. Frequency Rev. F | Page 12 of 28 1000 06591-068 -120 06591-027 DISTORTION (dBc) 100 FREQUENCY (MHz) 06591-029 -90 Data Sheet -30 ADA4937-1/ADA4937-2 28 VOUT, dm PSRR, VS = 3.3V VOUT, dm PSRR, VS = 5.0V -40 26 G = +1 G = +2 G = +4 24 NOISE FIGURE (dB) PSRR (dB) -50 -60 -70 -80 22 20 18 16 14 -90 10 100 1000 FREQUENCY (MHz) 10 10 0 Figure 34. Noise Figure vs. Frequency 5 S11 S22 3 -15 2 -20 -25 VOLTAGE (V) -30 -35 -40 -45 1 0 -1 -2 -50 -3 -55 -4 -60 10 100 1000 FREQUENCY (MHz) -5 06591-032 1 TIME (4ns/DIV) Figure 32. Return Loss (S11, S22) vs. Frequency -55 Figure 35. Overdrive Recovery Time (Pulse Input) 5 SFDR, RL = 1k SFDR, RL = 200 -60 06591-069 S-PARAMETERS (dB) VIN x 3.16 VOUT, dm 4 -10 -65 100 FREQUENCY (MHz) Figure 31. PSRR vs. Frequency, RL = 200 -5 06591-034 1 06591-031 -100 12 VIN x 3 VOUT, dm 4 -65 3 -75 SIGNAL LEVEL (V) -80 -85 -90 -95 -100 2 1 0 -1 -2 -3 -105 -4 -115 -5 1 10 100 FREQUENCY (MHz) Figure 33. Spurious-Free Dynamic Range vs. Frequency and Load 06591-033 -110 +VS = +2.5V -VS = -2.5V 0 100 200 300 TIME (ns) 400 500 600 06591-070 DISTORTION (dBc) -70 Figure 36. Overdrive Amplitude Characteristics (Triangle Wave Input) Rev. F | Page 13 of 28 Data Sheet 60 60 55 55 50 50 45 45 SUPPLY CURRENT (mA) 40 35 +105C 30 +25C 25 20 +55C 0C 15 -40C 10 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 15 +55C -40C 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 POWER-DOWN VOLTAGE (V) Figure 40. Supply Current vs. PD for Various Temperatures, VS = 3.3 V 3.5 +VS = +2.5V -VS = -2.5V VOCM = 0V 0.15 3.0 2.5 VOUT, dm = 4V p-p VOUT, dm = 2V p-p +VS = +2.5V -VS = -2.5V VOCM = 0V 2.0 0.10 1.5 0.05 VOLTAGE (V) 0 -0.05 1.0 0.5 0 -0.5 -1.0 -1.5 -0.10 -2.0 -2.5 -0.15 06591-071 -3.0 TIME (1ns/DIV) -3.5 TIME (1ns/DIV) Figure 41. Large Signal Pulse Response Figure 38. Small Signal Pulse Response 4.00 2.60 VS = +5V G=1 RL, dm = 1k 2.58 06591-074 VOLTAGE (V) 0C 20 0 1.0 0.20 VS = +5V G=1 RL, dm = 1k 3.75 3.50 2.56 OUTPUT VOLTAGE (V) 3.25 2.54 2.52 2.50 2.48 2.46 2.44 3.00 2.75 2.50 2.25 2.00 1.75 1.50 2.42 1.25 TIME (2ns/DIV) 06591-072 OUTPUT VOLTAGE (V) +105C 25 06591-040 1.2 06591-037 1.1 Figure 37. Supply Current vs. PD for Various Temperatures 2.40 +25C 30 5 POWER-DOWN VOLTAGE (V) -0.20 35 10 5 0 1.0 40 1.00 TIME (2ns/DIV) Figure 42. Large Signal VOCM Pulse Response Figure 39. Small Signal VOCM Pulse Response Rev. F | Page 14 of 28 06591-073 SUPPLY CURRENT (mA) ADA4937-1/ADA4937-2 Data Sheet ADA4937-1/ADA4937-2 10 10 G=1 9 8 POWER-DOWN PULSE IMPEDANCE () AMPLITUDE (V) 7 6 5 4 1 3 OUTPUT 2 0 0.5 1.0 1.5 2.0 2.5 0.1 0.01 0.1 1 TIME (ms) 10 100 1k FREQUENCY (MHz) Figure 43. PD Response vs. Time Figure 46. Closed-Loop Output Impedance 2 -40 1.0 -50 VIN INPUT2, OUTPUT1 -60 1 0.5 -70 SETTLING ERROR -80 0 0.1 0 -0.1 -1 -0.5 VIN (V) CROSSTALK (dB) 06591-146 -0.5 -90 -100 INPUT1, OUTPUT2 -110 SETTLING ERROR (%) 0 -1.0 06591-043 1 -120 100 1000 FREQUENCY (MHz) -2 -1.0 TIME (1ns/DIV) Figure 44. Crosstalk vs. Frequency for ADA4937-2 Figure 47. 0.1% Settling Time OPEN-LOOP GAIN (dB) 70 10 50 60 PHASE 50 GAIN 0 -50 40 30 -100 20 -150 10 -200 0 -250 -10 1 10 100 1k 10k 100k 1M FREQUENCY (Hz) 10M 06591-045 INPUT VOLTAGE NOISE (nV/ Hz) 100 Figure 45. Voltage Spectral Noise Density, RTI -20 1 10 100 1k 10k 100k 1M 10M 100M 1G -300 10G FREQUENCY (Hz) Figure 48. Open-Loop Gain and Phase vs. Frequency Rev. F | Page 15 of 28 OPEN-LOOP PHASE (Degrees) 10 06591-401 1 06591-044 -140 0.3 06591-147 -130 ADA4937-1/ADA4937-2 Data Sheet TEST CIRCUITS 200 5V 50 200 VIN VOCM 61.9 ADA4937 1k 200 06591-046 27.5 200 Figure 49. Equivalent Basic Test Circuit 200 5V 50 200 VIN 50 VOCM 61.9 ADA4937 200 50 06591-047 27.5 200 Figure 50. Test Circuit for Output Balance 200 5V VIN FILTER 61.9 0.1F 200 VOCM 412 FILTER ADA4937 0.1F 200 412 27.5 200 Figure 51. Test Circuit for Distortion Measurements Rev. F | Page 16 of 28 06591-048 50 Data Sheet ADA4937-1/ADA4937-2 TERMINOLOGY -FB +IN VOCM -DIN Common-Mode Voltage Common-mode voltage refers to the average of two node voltages. The output common-mode voltage is defined as RF -OUT ADA4937 RG R F -IN RL, dm VOUT, dm +OUT +FB VOUT, cm = (V+OUT + V-OUT)/2 06591-049 +DIN RG Figure 52. Circuit Definitions Differential Voltage Differential voltage refers to the difference between two node voltages. For example, the output differential voltage (or equivalently, output differential-mode voltage) is defined as VOUT, dm = (V+OUT - V-OUT) where V+OUT and V-OUT refer to the voltages at the +OUT and -OUT terminals with respect to a common reference. Output Balance Output balance is a measure of how close the differential signals are to being equal in amplitude and opposite in phase. Output balance is most easily determined by placing a well-matched resistor divider between the differential voltage nodes and comparing the magnitude of the signal at the midpoint of the divider with the magnitude of the differential signal (see Figure 50). By this definition, output balance is the magnitude of the output common-mode voltage divided by the magnitude of the output differential mode voltage. Output Balance Error Rev. F | Page 17 of 28 VOUT , cm VOUT , dm ADA4937-1/ADA4937-2 Data Sheet THEORY OF OPERATION The ADA4937-1/ADA4937-2 differ from conventional operational amplifiers in that they have two outputs whose voltages move in opposite directions. Like an operational amplifier, they rely on open-loop gain and negative feedback to force these outputs to the desired voltages. The ADA4937-1/ADA4937-2 behave much like standard voltage feedback operational amplifiers, which makes it easier to perform single-ended-to-differential conversions, common-mode level shifting, and amplifications of differential signals. Also like an operational amplifier, the ADA4937-1/ADA4937-2 have high input impedance and low output impedance. Two feedback loops control the differential and common-mode output voltages. The differential feedback loop, set with external resistors, controls only the differential output voltage. The common-mode feedback loop controls only the common-mode output voltage. This architecture makes it easy to set the output common-mode level to any arbitrary value. It is forced, by internal common-mode feedback, to be equal to the voltage applied to the VOCM input without affecting the differential output voltage. The ADA4937-1/ADA4937-2 architecture results in outputs that are highly balanced over a wide frequency range without requiring tightly matched external components. The commonmode feedback loop forces the signal component of the output common-mode voltage to zero. This results in nearly perfectly balanced differential outputs that are identical in amplitude and are exactly 180 apart in phase. SETTING THE CLOSED-LOOP GAIN The differential-mode gain of the circuit in Figure 52 can be determined by VOUT , dm VIN , dm RF RG This assumes that the input resistors (RG) and feedback resistors (RF) on each side are equal. ESTIMATING THE OUTPUT NOISE VOLTAGE To estimate the differential output noise of the ADA4937-1/ ADA4937-2 use the noise model in Figure 53. The input-referred noise voltage density, vnIN, is modeled as a differential input, and the noise currents, inIN- and inIN+, appear between each input and ground. The noise currents are assumed to be equal and produce a voltage across the parallel combination of the gain and feedback resistances. vn, cm is the noise voltage density at the VOCM pin. Each of the four resistors contributes (4kTRx)1/2. Table 9 summarizes the input noise sources, the multiplication factors, and the outputreferred noise density terms. VnRG1 RG1 VnRF1 RF1 inIN+ + inIN- VnIN ADA4937 VnOD The ADA4937-1/ADA4937-2 use open-loop gain and negative feedback to force their differential and common-mode output voltages in such a way as to minimize the differential and common-mode error voltages. The differential error voltage is defined as the voltage between the differential inputs labeled +IN and -IN (see Figure 52). For most purposes, this voltage can be assumed to be zero. Similarly, the difference between the actual output common-mode voltage and the voltage applied to VOCM can also be assumed to be zero. Starting from these two assumptions, any application circuit can be analyzed. VnRG2 RG2 RF2 VnCM VnRF2 06591-050 VOCM ANALYZING AN APPLICATION CIRCUIT Figure 53. ADA4937-1/ADA4937-2 Noise Model Table 9. Output Noise Voltage Density Calculations Input Noise Contribution Differential Input Inverting Input Noninverting Input VOCM Input Gain Resistor RG1 Gain Resistor RG2 Feedback Resistor RF1 Feedback Resistor RF2 Input Noise Term vnIN inIN- inIN+ vn, cm vnRG1 vnRG2 vnRF1 vnRF2 Input Noise Voltage Density vnIN inIN- x (RG2||RF2) inIN+ x (RG1||RF1) vn, cm (4kTRG1)1/2 (4kTRG2)1/2 (4kTRF1)1/2 (4kTRF2)1/2 Rev. F | Page 18 of 28 Output Multiplication Factor GN GN GN GN(1 - 2) GN(1 - 1) GN(1 - 2) 1 1 Output Noise Voltage Density Term vnO1 = GN(vnIN) vnO2 = GN[inIN- x (RG2||RF2)] vnO3 = GN[inIN+ x (RG1||RF1)] vnO4 = GN(1 - 2)(vn, cm) vnO5 = GN(1 - 1)(4kTRG1)1/2 vnO6 = GN(1 - 2)(4kTRG2)1/2 vnO7 = (4kTRF1)1/2 vnO8 = (4kTRF2)1/2 Data Sheet ADA4937-1/ADA4937-2 RF Similar to the case of a conventional operational amplifier, the output noise voltage densities can be estimated by multiplying the input-referred terms at +IN and -IN by the appropriate output factor, where: 2 GN is the circuit noise gain. 1 2 RG1 RG2 and 2 are the feedback factors. 1 RF1 RG1 RF2 RG2 Figure 54. ADA4937-1/ADA4937-2 Configured for Balanced (Differential) Inputs When RF1/RG1 = RF2/RG2, then 1 = 2 = , and the noise gain becomes For an unbalanced, single-ended input signal (see Figure 55), the input impedance is +VS -DIN +IN VOCM RG VOUT, dm -IN RF 1 R 1 F RG R IN , cm Note that the output noise from VOCM goes to zero in this case. The total differential output noise density, vnOD, is the root-sumsquare of the individual output noise terms. R G RF 1 2 RG R F RF +VS 8 2 vnOi RG RS i 1 VOCM RT IMPACT OF MISMATCHES IN THE FEEDBACK NETWORKS ADA4937 VOUT, dm RG As previously mentioned in the Setting the Closed-Loop Gain section), even if the external feedback networks (RF/RG) are mismatched, the internal common-mode feedback loop still forces the outputs to remain balanced. The amplitudes of the signals at each output remain equal and 180 out of phase. The input-to-output differential mode gain varies proportionately to the feedback mismatch, but the output balance is unaffected. As well as causing a noise contribution from VOCM, ratio matching errors in the external resistors result in a degradation of the ability of the circuit to reject input common-mode signals, much the same as for a four-resistor difference amplifier made from a conventional operational amplifier. In addition, if the dc levels of the input and output commonmode voltages are different, matching errors result in a small differential-mode output offset voltage. When G = 1, with a ground referenced input signal and the output common-mode level set to 2.5 V, an output offset of as much as 25 mV (1% of the difference in common-mode levels) can result if 1% tolerance resistors are used. Resistors of 1% tolerance result in a worstcase input CMRR of approximately 40 dB, a worst-case differential-mode output offset of 25 mV due to 2.5 V level shift, and no significant degradation in output balance error. RS RT 06591-052 vnOD RG 06591-051 +DIN RF Figure 55. ADA4937-1/ADA4937-2 Configured for Unbalanced (Single-Ended) Input The input impedance of the circuit is effectively higher than it is for a conventional operational amplifier connected as an inverter because a fraction of the differential output voltage appears at the inputs as a common-mode signal, partially bootstrapping the voltage across the Input Gain Resistor RG. Terminating a Single-Ended Input This section explains how to properly terminate a single-ended input to the ADA4937-1/ADA4937-2. Using a simple example with an input source of 2 V and a source resistor of 50 , four simple steps must be followed. 1. The input impedance must be calculated using the formula R IN RF RIN 267 CALCULATING THE INPUT IMPEDANCE FOR AN APPLICATION CIRCUIT The effective input impedance of a circuit depends on whether the amplifier is being driven by a single-ended or differential signal source. For balanced differential input signals, as shown in Figure 54, the input impedance (RIN, dm) between the inputs (+DIN and -DIN) is simply RIN, dm = 2 x RG. RG 200 267 RF 200 1 1 2 ( 200 200 ) R R 2 ( ) F G VS 2V 200 +VS RS RG 50 200 VOCM ADA4937 RL 200 -VS RF 200 Figure 56. Single-Ended Input Impedance RIN Rev. F | Page 19 of 28 VO RG 06591-081 GN ADA4937 ADA4937-1/ADA4937-2 RF For the source termination to be 50 , the termination resistor (RT) is calculated using RT||RIN = 50 , which makes RT equal to 61.9 . +VS RS RF 200 +VS 50 RS VS 2V VS 2V RTS 27.4 200 RT 61.9 RG RT 61.9 200 VOCM VOCM ADA4937 RL RF Figure 60. Complete Single-Ended-to-Differential System 06591-082 -VS RF 200 Figure 57. Adding Termination Resistor RT RS RTH VTH 1.1V 27.4 06591-083 RT 61.9 SETTING THE OUTPUT COMMON-MODE VOLTAGE Figure 58. Calculating Thevenin Equivalent RTS = RTH = RS||RT = 27.4 . Note that VTH is not equal to VS/2, which is the case if the termination is not affected by the amplifier circuit. RF VTH 1.1V RTH RG 200 VOCM ADA4937 VO RL 0.97V RG It is also possible to connect the VOCM input to a common-mode level (CML) output of an ADC. However, care must be taken to ensure that the output has sufficient drive capability. The input impedance of the VOCM pin is approximately 10 k. If multiple ADA4937-1/ADA4937-2 devices share one reference output, it is recommended that a buffer be used. 200 -VS RF 200 06591-084 RTS 27.4 Figure 59. Balancing Gain Resistor RG 4. The feedback resistor is calculated to adjust the output voltage. a. The VOCM pin of the ADA4937-1/ADA4937-2 is internally biased at a voltage approximately equal to the midsupply point, [(+VS) + (-VS)]/2. Relying on this internal bias results in an output common-mode voltage that is within about 100 mV of the expected value. In cases where more accurate control of the output commonmode level is required, it is recommended that an external source, or resistor divider (10 k or greater resistors), be used. The output common-mode offset listed in Table 2 and Table 4 assumes that the VOCM input is driven by a low impedance voltage source. 200 +VS 27.4 INPUT COMMON-MODE VOLTAGE RANGE IN SINGLE-SUPPLY APPLICATIONS The ADA4937-1/ADA4937-2 are optimized for level-shifting ground-referenced input signals. As such, the center of the input common-mode range is shifted approximately 1 V down from midsupply. For 5 V single-supply operation, the input commonmode range at the summing nodes of the amplifier is 0.3 V to 3.0 V, and 0.3 V to 1.2 V with a 3.3 V supply. To avoid clipping at the outputs, the voltage swing at the +IN and -IN terminals must be confined to these ranges. To compensate for the imbalance of the gain resistors, a correction resistor (RTS) is added in series with the inverting Input Gain Resistor RG. RTS is equal to the Thevenin equivalent of the Source Resistance RS||RT. VS 2V VO -VS VO 200 50 RL 200 RG 3. ADA4937 RG RG 50 50 06591-085 2. Data Sheet Table 10 and Table 11 list several common gain settings, associated resistor values, input impedances, and output noise density values for both balanced and unbalanced input configurations. To make the output voltage VOUT = 1 V, RF must be calculated using the following formula: POWER-DOWN OPERATION V (RG RTS ) 1 (200 27.4) RF OUT 207 VTH 1.1 To make VO = VS = 2 V to recover the loss due to the input termination, RF must be The ADA4937-1/ADA4937-2 power-down pin features an internal 25 k pull-up resistor to the positive supply (+VS). This ensures that, with the power-down pin left unconnected (floating), the ADA4937-1/ADA4937-2 turn on. Applying a voltage of 1 V turns the ADA4937-1/ADA4937-2 off. V (RG RTS ) 2 (200 27.4) RF OUT 414 VTH 1.1 Rev. F | Page 20 of 28 Data Sheet ADA4937-1/ADA4937-2 Table 10. Differential Ground-Referenced Input, DC-Coupled, 1 k Load; See Figure 54 Nominal Gain (dB) 0 6 10 14 RF () 200 402 402 402 RG () 200 200 127 80.6 RIN, dm () 400 400 254 161 Differential Output Noise Density (nV/Hz) 5.8 9.6 12.1 16.2 Table 11. Single-Ended Ground-Referenced Input, DC-Coupled, RS = 50 , RL = 1 k; See Figure 55 Nominal Gain (dB) 0 6 10 14 1 RF () 200 402 402 402 RG1 () 200 200 127 80.6 RT () 61.9 60.4 66.5 76.8 RIN, cm () 267 301 205 138 RG2 ()1 226 228 155 111 RG2 = RG1 + (RS||RT) Rev. F | Page 21 of 28 Differential Output Noise Density (nV/Hz) 5.5 8.6 10.1 12.2 ADA4937-1/ADA4937-2 Data Sheet LAYOUT, GROUNDING, AND BYPASSING As high speed devices, the ADA4937-1/ADA4937-2 are sensitive to the PCB environment in which they operate. Realizing their superior performance requires attention to the details of high speed PCB design. This section shows a detailed example of how the design issues of the ADA4937-1 is addressed. Bypass the power supply pins as close to the device as possible and directly to a nearby ground plane. Use high frequency ceramic chip capacitors. It is recommended that two parallel bypass capacitors (1000 pF and 0.1 F) be used for each supply with the 1000 pF capacitor placed closer to the device; further away, provide low frequency bypassing using 10 F tantalum capacitors from each supply to ground. The first requirement is a solid ground plane that covers as much of the board area around the ADA4937-1 as possible. However, the area near the feedback resistors (RF), input gain resistors (RG), and the input summing nodes (Pin 2 and Pin 3) must be cleared of all ground and power planes (see Figure 61). Clearing the ground and power planes minimizes any stray capacitance at these nodes and prevents peaking of the response of the amplifier at high frequencies. Signal routing must be short and direct to avoid parasitic effects. Wherever complementary signals exist, provide a symmetrical layout to maximize balanced performance. When routing differential signals over a long distance, keep PCB traces close together and twist any differential wiring to minimize loop area. Doing this reduces radiated energy and makes the circuit less susceptible to interference. The thermal resistance, JA, is specified for the device, including the exposed pad, soldered to a high thermal conductivity 4-layer circuit board, as described in EIA/JESD 51-7. 1.30 0.80 06591-086 06591-087 1.30 0.80 Figure 62. Recommended PCB Thermal Attach Pad Dimensions (mm) Figure 61. Ground and Power Plane Voiding in Vicinity of RF and RG 1.30 TOP METAL GROUND PLANE 0.30 PLATED VIA HOLE 06591-088 POWER PLANE BOTTOM METAL Figure 63. Cross-Section of 4-layer PCB Showing Thermal Via Connection to Buried Ground Plane (Dimensions in mm) Rev. F | Page 22 of 28 Data Sheet ADA4937-1/ADA4937-2 HIGH PERFORMANCE ADC DRIVING The ADA4937-1/ADA4937-2 are ideally suited for broadband IF applications. The circuit in Figure 64 shows a front-end connection for an ADA4937-1 driving an AD9445, 14-bit, 105 MSPS ADC. The AD9445 achieves optimum performance when driven differentially. The ADA4937-1/ADA4937-2 eliminate the need for a transformer to drive the ADC and performs a single-endedto-differential conversion and buffering of the driving signal. The signal generator has a symmetric, ground-referenced bipolar output. The VOCM pin of the ADA4937-1/ADA4937-2 remains unconnected allowing the internal divider to set the output common-mode voltage at midsupply; one half of the common-mode voltage is fed back to the summing nodes, biasing -IN and +IN at 1.25 V. For a common-mode voltage of 2.5 V, each ADA4937-1/ADA4937-2 output swings between 2.0 V and 3.0 V, providing a 2 V p-p differential output. The ADA4937-1/ADA4937-2 are configured with a single 5 V supply and unity gain for a single-ended input to differential output. The 61.9 termination resistor, in parallel with the singleended input impedance of 267 , provides a 50 termination for the source. The additional 26 (226 total) at the inverting input balances the parallel impedance of the 50 source and the termination resistor driving the noninverting input. The output of the amplifier is ac-coupled to the ADC through a second-order, low-pass filter with a cutoff frequency of 100 MHz. This reduces the noise bandwidth of the amplifier and isolates the driver outputs from the ADC inputs. The AD9445 is configured for a 2 V p-p full-scale input by connecting the SENSE pin to AGND, as shown in Figure 64. 5V (A) 3.3V (A) 3.3V (D) 200 5V 200 61.9 SIGNAL GENERATOR VOCM 0.1F + AVDD2 AVDD1 DRVDD AD9445 VIN- BUFFER T/H 24.3 ADA4937-1 226 30nH 47pF ADC 24.3 0.1F 30nH 14 VIN+ CLOCK/ TIMING 200 REF AGND SENSE 06591-054 50 Figure 64. Driving an AD9445, 14-Bit, 105 MSPS ADC Rev. F | Page 23 of 28 ADA4937-1/ADA4937-2 Data Sheet The circuit in Figure 66 shows a simplified front-end connection for an ADA4937-1 driving an AD9246, 14-bit, 125 MSPS ADC. The AD9246 achieves optimum performance when driven differentially. The ADA4937-1/ADA4937-2 perform the singleended-to-differential conversion, eliminating the need for a transformer to drive the ADC. The AD9246 is set for a 2 V p-p full-scale input by connecting the SENSE pin to AGND. The inputs of the AD9246 are biased at 1 V by connecting the CML output, as shown in Figure 66. The circuit was tested with a -1 dBFS signal at various frequencies. Figure 65 shows a plot of the second- and third-order harmonic distortion (HD2/HD3) vs. frequency. The ADA4937-1/ADA4937-2 are configured with a single 5 V supply and a gain of ~2 V/V for a single-ended input to differential output. The 76.8 termination resistor, in parallel with the single-ended input impedance of 137 , provides a 50 ac termination for the source. The additional 30 (120 total) at the inverting input balances the parallel ac impedance of the 50 source and the termination resistor driving the noninverting input. -75 The signal generator has a symmetric, ground-referenced bipolar output. The VOCM pin of the ADA4937-1/ADA4937-2 remains unconnected; therefore, the internal pull-ups set the output common-mode voltage to midsupply. A portion of this is fed back to the summing nodes, biasing -IN and +IN at 0.55 V. For a common-mode voltage of 2.5 V, each ADA4937-1/ADA4937-2 output swings between 2.0 V and 3.0 V, providing a 2 V p-p differential output. -80 HD3 -85 HD2 -90 -95 -100 0 20 40 60 80 FREQUENCY (MHz) 200 50 10F 90 90 10F + ADA4937-1 200 10pF 200 10F 76.8 33 AVDD DRVDD VIN- AD9246 VIN+ 33 D13 TO D0 AGND SENSE CML 06591-056 VIN 1.8V 5V 76.8 10F 120 Figure 65. HD2/HD3 for Combination of ADA4937-1/ADA4937-2 and AD9246 ADC The output is ac-coupled to a single-pole, low-pass filter. This reduces the noise bandwidth of the amplifier and provides some level of isolation from the switched capacitor inputs of the ADC. 50 100 06591-055 HARMONIC DISTORTION (dBc) G = +2 200 Figure 66. Driving an AD9246, 14-Bit, 125 MSPS ADC Rev. F | Page 24 of 28 Data Sheet ADA4937-1/ADA4937-2 ended input impedance of 306 , provides a 50 termination for the source. The additional 26 (226 total) at the inverting input balances the parallel impedance of the 50 source and the termination resistor that drives the noninverting input. The signal generator has a symmetric, ground-referenced bipolar output. The VOCM pin is connected to the CML output of the AD9230, and sets the output common mode of the ADA4937-1/ADA4937-2 at 1.4 V. One third of the output common-mode voltage of the amplifier is fed back to the summing nodes, biasing -IN and +IN at ~0.5 V. For a common-mode voltage of 1.4 V, each ADA4937-1/ ADA4937-2 output swings between 1.09 V and 1.71 V, providing a 1.25 V p-p differential output. 3.3 V OPERATION The ADA4937-1/ADA4937-2 provide excellent performance in 3.3 V single-supply applications. Significant power savings can be realized when the ADA4937-1/ADA4937-2 are used in combination with a low voltage ADC. The circuit in Figure 67 is an example of the ADA4937-1 driving an AD9230, 12-bit, 250 MSPS ADC that is specified to operate with a single 1.8 V supply. The performance of the ADC is optimized when it is driven differentially, making the best use of the signal swing available within the 1.8 V supply. The ADA4937-1/ ADA4937-2 perform the single-ended-to-differential conversion, common-mode level-shifting, and buffering of the driving signal. A third-order, 125 MHz, low-pass filter between the ADA4937-1/ ADA4937-2 and the AD9230 reduces the noise bandwidth of the amplifier and isolates the driver outputs from the ADC inputs. The ADA4937-1/ADA4937-2 are configured with a single 3.3 V supply and a gain of 2 V/V for a single-ended input to differential output. The 59 termination resistor, in parallel with the single453 1.8V 3.3V VIN 200 59 VOCM 33 + ADA4937-1 10pF 56nH AVDD VIN- DRVDD AD9230 30pF VIN+ 33 226 56nH AGND D11 TO D0 CML 06591-057 50 453 Figure 67. Driving an AD9230, 12-Bit, 250 MSPS ADC Rev. F | Page 25 of 28 ADA4937-1/ADA4937-2 Data Sheet OUTLINE DIMENSIONS PIN 1 INDICATOR 3.10 3.00 SQ 2.90 0.30 0.23 0.18 13 0.50 BSC PIN 1 INDICATOR 16 1 12 EXPOSED PAD 1.45 1.30 SQ 1.15 4 9 0.80 0.75 0.70 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.20 REF SEATING PLANE 0.25 MIN BOTTOM VIEW FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. 111808-A TOP VIEW 5 8 0.50 0.40 0.30 COMPLIANT TO JEDEC STANDARDS MO-220-WEED. Figure 68. 16-Lead Lead Frame Chip Scale Package [LFCSP] 3 mm x 3 mm Body and 0.75 mm Package Height (CP-16-21) Dimensions shown in millimeters 0.30 0.25 0.20 0.50 BSC PIN 1 INDICATOR 24 19 18 1 EXPOSED PAD TOP VIEW 0.80 0.75 0.70 0.50 0.40 0.30 13 12 2.20 2.10 SQ 2.00 6 7 0.25 MIN BOTTOM VIEW 0.05 MAX 0.02 NOM FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. COPLANARITY 0.08 0.20 REF SEATING PLANE COMPLIANT TO JEDEC STANDARDS MO-220-WGGD-8. 06-11-2012-A PIN 1 INDICATOR 4.10 4.00 SQ 3.90 Figure 69. 24-Lead Lead Frame Chip Scale Package [LFCSP] 4 mm x 4 mm Body and 0.75 mm Package Height (CP-24-10) Dimensions shown in millimeters ORDERING GUIDE Model 1 ADA4937-1YCPZ-R2 ADA4937-1YCPZ-RL ADA4937-1YCPZ-R7 ADA4937-2YCPZ-R2 ADA4937-2YCPZ-RL ADA4937-2YCPZ-R7 1 Temperature Range -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C -40C to +105C Package Description 16-Lead LFCSP 16-Lead LFCSP 16-Lead LFCSP 24-Lead LFCSP 24-Lead LFCSP 24-Lead LFCSP Z = RoHS Compliant Part. Rev. F | Page 26 of 28 Package Option CP-16-21 CP-16-21 CP-16-21 CP-24-10 CP-24-10 CP-24-10 Ordering Quantity 250 5,000 1,500 250 5,000 1,500 Branding H1S H1S H1S Data Sheet ADA4937-1/ADA4937-2 NOTES Rev. F | Page 27 of 28 ADA4937-1/ADA4937-2 Data Sheet NOTES (c)2007-2016 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D06591-0-6/16(F) Rev. F | Page 28 of 28 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: ADA4937-1YCP-EBZ ADA4937-2YCP-EBZ