IL710 High Speed/High Temperature Digital Isolators Functional Diagram Features VOE IN1 OUT1 IL710 Truth Table VI L H L H VOE L L H H VO L H Z Z * * * * * * * * * * * * * +5 V/+3.3 V CMOS / TTL Compatible High Speed: 150 Mbps Typical (IL710S) High Temperature: -40C to +125C (IL710T) 1.5 mA/Channel Typical Quiescent Current 300 ps Typical Pulse Width Distortion (IL710S) 100 ps Typical Pulse Jitter 2 ns Channel-to-Channel Skew 10 ns Typical Propagation Delay Low EMC Footprint 30 kV/s Typical Common Mode Transient Immunity 2500 VRMS Isolation (1 min.) UL1577 and IEC 61010-2001 Approved 8-pin MSOP, SOIC, and PDIP Packages Applications * * * * * * * * * * * Digital Fieldbus RS-485 and RS-422 Multiplexed Data Transmission Data Interfaces Board-to-Board Communication Digital Noise Reduction Operator Interface Ground Loop Elimination Peripheral Interfaces Serial Communication Logic Level Shifting Description NVE's IL700 family of high-speed digital isolators are CMOS devices manufactured with NVE's patented* IsoLoop(R) spintronic Giant Magnetoresistive (GMR) technology. The IL710S is the world's fastest isolator of its type, with a 150 Mbps typical data rate. The symmetric magnetic coupling barrier provides a typical propagation delay of only 10 ns and a pulse width distortion as low as 300 ps (0.3 ns), achieving the best specifications of any isolator. Typical transient immunity of 30 kV/s is unsurpassed. The IL710 is ideal for isolating applications such as PROFIBUS, RS-485, and RS-422. The IL710 is available in 8-pin MSOP, SOIC, and PDIP packages. Standard and S-Grade parts are specified over a temperature range of -40C to +100C; T-Grade parts are specified over a temperature range of -40C to +125C. IsoLoop is a registered trademark of NVE Corporation. *U.S. Patent numbers 5,831,426; 6,300,617 and others. NVE Corporation 11409 Valley View Road, Eden Prairie, MN 55344-3617 REV. X Phone: (952) 829-9217 Fax: (952) 829-9189 www.IsoLoop.com (c)NVE Corporation IL710 Absolute Maximum Ratings Parameters Storage Temperature Ambient Operating Temperature(1) IL710T Supply Voltage Input Voltage Input Voltage Output Voltage Output Current Drive Lead Solder Temperature ESD Symbol TS Min. -55 TA -55 VDD1, VDD2 VI VOE VO IO -0.5 -0.5 -0.5 -0.5 Typ. Max. 150 125 135 7 VDD1+0.5 VDD2+0.5 VDD2+0.5 10 260 Units C Max. Units 100 125 5.5 VDD1 0.8 1 C C V V V s Max. Units 2 Test Conditions C V V V V mA C kV 10 sec. HBM Recommended Operating Conditions Parameters Ambient Operating Temperature IL710 and IL710S IL710T Supply Voltage Logic High Input Voltage Logic Low Input Voltage Input Signal Rise and Fall Times Symbol Min. TA TA VDD1, VDD2 VIH VIL tIR, tIF -40 -40 3.0 2.4 0 Symbol Min. Typ. Test Conditions Insulation Specifications Parameters Creepage Distance MSOP SOIC PDIP Leakage Current(5) Barrier Impedance(5) Typ. 3.01 4.04 7.04 mm mm mm A || pF 0.2 >1014||3 Test Conditions 240 VRMS, 60 Hz Package Characteristics Parameters Capacitance (Input-Output)(5) Thermal Resistance MSOP SOIC PDIP Package Power Dissipation Symbol CI-O Min. Typ. 1.1 JC JC JC PPD Max. 168 144 54 150 Units pF C/W C/W C/W mW Test Conditions f = 1 MHz Thermocouple at center underside of package f = 1 MHz, VDD = 5 V Safety and Approvals IEC61010-1 TUV Certificate Numbers: N1502812, N1502812-101 Classification as Reinforced Insulation Model IL710-1 IL710-2 IL710-3 Package MSOP PDIP SOIC UL 1577 Component Recognition Program File Number: E207481 Rated 2500VRMS for 1 minute Soldering Profile Per JEDEC J-STD-020C, MSL=2 2 Pollution Degree II II II Material Group III III III Max. Working Voltage 150 VRMS 300 VRMS 150 VRMS IL710 IL710 Pin Connections 1 2 3 4 5 6 VDD1 IN NC GND1 GND2 OUT 7 VOE 8 VDD2 Supply voltage Data In No internal connection Ground return for VDD1 Ground return for VDD2 Data Out Output enable. Internally held low with 100 k Supply voltage VDD1 VDD2 IN VOE NC OUT GND2 GND1 IL710 Timing Diagram Legend tPLH tPHL tPW tPLZ tPZH tPHZ tPZL tR tF 3 Propagation Delay, Low to High Propagation Delay, High to Low Minimum Pulse Width Propagation Delay, Low to High Impedance Propagation Delay, High Impedance to High Propagation Delay, High to High Impedance Propagation Delay, High Impedance to Low Rise Time Fall Time IL710 3.3 Volt Electrical Specifications Electrical specifications are Tmin to Tmax unless otherwise stated. Parameters Symbol Min. Typ. DC Specifications Input Quiescent Supply Current IDD1 8 Output Quiescent Supply Current IDD2 1.5 Logic Input Current II -10 V -0.1 VDD DD Logic High Output Voltage VOH 0.8 x VDD 0.9 x VDD 0 Logic Low Output Voltage VOL 0.5 Switching Specifications Maximum Data Rate IL710 and IL710T 100 110 IL710S 130 140 Pulse Width(7) PW 10 7.5 Propagation Delay Input to Output tPHL 12 (High to Low) Propagation Delay Input to Output 12 tPLH (Low to High) Propagation Delay Enable to Output tPHZ 3 (High to High Impedance) Propagation Delay Enable to Output tPLZ 3 (Low to High Impedance) Propagation Delay Enable to Output 3 tPZH (High Impedance to High) Propagation Delay Enable to Output 3 tPZL (High Impedance to Low) Pulse Width Distortion(2) 2 IL710 and IL710T PWD 1 IL710S Pulse Jitter(8) tJ Propagation Delay Skew(3) tPSK 4 Output Rise Time (10%-90%) tR 2 Output Fall Time (10%-90%) tF 2 Common Mode Transient Immunity |CM |,|CM | 20 30 H L (Output Logic High or Logic Low)(4) (6) Dynamic Power Consumption 140 4 Max. Units 10 2 10 A mA A V 0.1 0.8 V Mbps Mbps ns Test Conditions IO = -20 A, VI = VIH IO = -4 mA, VI = VIH IO = 20 A, VI = VIL IO = 4 mA, VI = VIL CL = 15 pF CL = 15 pF 50% Points, VO 18 ns CL = 15 pF 18 ns CL = 15 pF 5 ns CL = 15 pF 5 ns CL = 15 pF 5 ns CL = 15 pF 5 ns CL = 15 pF 3 3 100 6 4 4 ns CL = 15 pF ps ns ns ns CL = 15 pF CL = 15 pF CL = 15 pF CL = 15 pF kV/s 240 A/MHz VCM = 300 V IL710 5 Volt Electrical Specifications Electrical specifications are Tmin to Tmax unless otherwise stated. Parameters Symbol Min. Typ. DC Specifications Input Quiescent Supply Current IDD1 10 Output Quiescent Supply Current IDD2 2 Logic Input Current II -10 VDD-0.1 VDD Logic High Output Voltage VOH 0.8 x VDD 0.9 x VDD 0 Logic Low Output Voltage VOL 0.5 Switching Specifications Maximum Data Rate IL710 and IL710T 100 110 IL710S 130 150 Pulse Width(7) PW 10 7.5 Propagation Delay Input to Output tPHL 10 (High to Low) Propagation Delay Input to Output 10 tPLH (Low to High) Propagation Delay Enable to Output tPHZ 3 (High to High Impedance) Propagation Delay Enable to Output tPLZ 3 (Low to High Impedance) Propagation Delay Enable to Output 3 tPZH (High Impedance to High) Propagation Delay Enable to Output 3 tPZL (High Impedance to Low) Pulse Width Distortion(2) 2 IL710 and IL710T PWD 0.3 IL710S Propagation Delay Skew(3) tPSK 4 Output Rise Time (10%-90%) tR 1 Output Fall Time (10%-90%) tF 1 Common Mode Transient Immunity |CMH|,|CML| 20 30 (Output Logic High or Logic Low)(4) (6) Dynamic Power Consumption 200 Max. Units 15 3 10 A mA A V 0.1 0.8 V Mbps Mbps ns Test Conditions IO = -20 A, VI = VIH IO = -4 mA, VI = VIH IO = 20 A, VI = VIL IO = 4 mA, VI = VIL CL = 15 pF CL = 15 pF 50% Points, VO 15 ns CL = 15 pF 15 ns CL = 15 pF 5 ns CL = 15 pF 5 ns CL = 15 pF 5 ns CL = 15 pF 5 ns CL = 15 pF 3 3 6 3 3 ns CL = 15 pF ns ns ns CL = 15 pF CL = 15 pF CL = 15 pF kV/s 340 Vcm = 300 V A/MHz Notes (apply to both 3.3 V and 5 V specifications): 1. Absolute maximum ambient operating temperature means the device will not be damaged if operated under these conditions. It does not guarantee performance. 2. PWD is defined as |tPHL - tPLH|. %PWD is equal to PWD divided by pulse width. 3. tPSK is the magnitude of the worst-case difference in tPHL and/or tPLH between devices at 25C. 4. CMH is the maximum common mode voltage slew rate that can be sustained while maintaining VO > 0.8 VDD2. CML is the maximum common mode input voltage that can be sustained while maintaining VO < 0.8 V. The common mode voltage slew rates apply to both rising and falling common mode voltage edges. 5. Device is considered a two terminal device: pins 1-4 shorted and pins 5-8 shorted. 6. Dynamic power consumption is calculated per channel and is supplied by the channel's input side power supply. 7. Minimum pulse width is the minimum value at which specified PWD is guaranteed. 8. 66,535-bit pseudo-random binary signal (PRBS) NRZ bit pattern with no more than five consecutive 1s or 0s; 800 ps transition time. 5 IL710 Application Information Electrostatic Discharge Sensitivity Power Supply Decoupling This product has been tested for electrostatic sensitivity to the limits stated in the specifications. However, NVE recommends that all integrated circuits be handled with appropriate care to avoid damage. Damage caused by inappropriate handling or storage could range from performance degradation to complete failure. Both power supplies to these devices should be decoupled with low ESR 47 nF ceramic capacitors. Ground planes for both GND1 and GND2 are highly recommended for data rates above 10 Mbps. Capacitors must be located as close as possible to the VDD pins. Signal Status on Start-up and Shut Down Electromagnetic Compatibility To minimize power dissipation, input signals are differentiated and then latched on the output side of the isolation barrier to reconstruct the signal. This could result in an ambiguous output state depending on power up, shutdown and power loss sequencing. Therefore, the designer should consider including an initialization signal in the start-up circuit. Initialization consists of toggling the input either high then low, or low then high. IsoLoop Isolators have the lowest EMC footprint of any isolation technology. IsoLoop Isolators' Wheatstone bridge configuration and differential magnetic field signaling ensure excellent EMC performance against all relevant standards. These isolators are fully compliant with generic EMC standards EN50081, EN50082-1 and the umbrella line-voltage standard for Information Technology Equipment (ITE) EN61000. NVE has completed compliance tests in the categories below: Data Transmission Rates The reliability of a transmission system is directly related to the accuracy and quality of the transmitted digital information. For a digital system, those parameters which determine the limits of the data transmission are pulse width distortion and propagation delay skew. EN50081-1 Residential, Commercial & Light Industrial Methods EN55022, EN55014 EN50082-2: Industrial Environment Methods EN61000-4-2 (ESD), EN61000-4-3 (Electromagnetic Field Immunity), EN61000-4-4 (Electrical Transient Immunity), EN61000-4-6 (RFI Immunity), EN61000-4-8 (Power Frequency Magnetic Field Immunity), EN61000-4-9 (Pulsed Magnetic Field), EN61000-4-10 (Damped Oscillatory Magnetic Field) ENV50204 Radiated Field from Digital Telephones (Immunity Test) Propagation delay is the time taken for the signal to travel through the device. This is usually different when sending a low-to-high than when sending a high-to-low signal. This difference, or error, is called pulse width distortion (PWD) and is usually in nanoseconds. It may also be expressed as a percentage: PWD% = Maximum Pulse Width Distortion (ns) Signal Pulse Width (ns) Immunity to external magnetic fields is even higher if the field direction is "end-to-end" rather than to "pin-to-pin" as shown in the diagram below: x 100% For example, with data rates of 12.5 Mbps: PWD% = 3 ns x 100% = 3.75% 80 ns This figure is almost three times better than any available optocoupler with the same temperature range, and two times better than any optocoupler regardless of published temperature range. IsoLoop isolators exceed the 10% maximum PWD recommended by PROFIBUS, and will run to nearly 35 Mb within the 10% limit. Cross-axis Field Direction Propagation delay skew is the signal propagation difference between two or more channels. This becomes significant in clocked systems because it is undesirable for the clock pulse to arrive before the data has settled. Short propagation delay skew is therefore especially critical in high data rate parallel systems for establishing and maintaining accuracy and repeatability. Worstcase channel-to-channel skew in an IL700 Isolator is only 3 ns, which is ten times better than any optocoupler. IL700 Isolators have a maximum propagation delay skew of 6 ns, which is five times better than any optocoupler. Dynamic Power Consumption IsoLoop Isolators achieve their low power consumption from the way they transmit data across the isolation barrier. By detecting the edge transitions of the input logic signal and converting these to narrow current pulses, a magnetic field is created around the GMR Wheatstone bridge. Depending on the direction of the magnetic field, the bridge causes the output comparator to switch following the input logic signal. Since the current pulses are narrow, about 2.5 ns, the power consumption is independent of mark-to-space ratio and solely dependent on frequency. This has obvious advantages over optocouplers, which have power consumption heavily dependent on mark-to-space ratio. 6 IL710 Application Diagrams Isolated PROFIBUS / RS-485 Isolation Boundary RS-485 Truth Table TXD RTS 1 0 0 0 1 1 0 1 A Z Z 1 0 B Z Z 0 1 RXD X X 1 0 IL710 IL710 ISL8485 Note: VDD1 and VISO should be decoupled with 10 nF ceramic capacitors at IL710 supply pins. IL710 NVE offers a unique line of PROFIBUS/RS-485 transceivers, but IL710 isolators can also be used as part of multi-chip designs using nonisolated PROFIBUS transceivers. 7 IL710 Isolated USB Isolation Boundary All power supplied by USB node's external supply on this side of isolation boundary Power supplied by USB bus power this side of isolation boundary +3.3V R1 1.5k USPB NET2890 ISO_USB+ 3 4 USBM ISO_USB- 27 USBOE 5 x IL710 In this circuit, power is supplied by USB bus power on one side of the isolation barrier, and the USB node's external supply on the other side of the barrier. IL700 Isolators are specified with just 3 ns worst-case pulse width distortion. 8 IL710 Package Drawings, Dimensions and Specifications 8-pin MSOP 0.114 (2.90) 0 0.122 (3.10) 6 0.016 (0.40) 0.027 (0.70) 0.032 (0.80) 0.043 (1.10) 0.114 (2.90) 0.189 (4.80) 0.197 (5.00) 0.122 (3.10) 0.002 (0.05) 0.006 (0.15) 0.028 (0.70) 0.024 (0.60) NOTE: Pin spacing is a BASIC dimension; tolerances do not accumulate 0.005 (0.13) 0.009 (0.23) 0.010 (0.25) 0.016 (0.40) 8-pin SOIC Package Dimensions in inches (mm) 0.189 (4.8) 0 0.197 (5.0) 8 0.016 (0.40) 0.050 (1.27) 0.054 (1.37) 0.228 (5.8) 0.150 (3.8) 0.069 (1.75) 0.244 (6.2) 0.157 (4.0) 0.010 (0.25) 0.004 (0.10) 0.020 (0.50) 0.010 (0.25) 0.040 (1.0) 1 2 x45 3 0.060 (1.5) NOTE: Pin spacing is a BASIC dimension; tolerances do not accumulate 0.008 (0.19) 0.013 (0.33) 0.010 (0.25) 0.020 (0.50) 8-pin PDIP 0.29 (6.4) 0.31 (7.9) 0.12 (3.05) 0.24 (6.1) 0.15 (3.81) 0.26 (6.6) 0.008 (0.2) 0.015 (0.4) 0.015 (0.38) 0.035 (0.89) 0.36 (9.0) 0.40 (10.2) 0.030 (0.76) 0.30 (7.6) 0.09 (2.3) 0.045 (1.14) 0.37 (9.4) 0.11 (2.8) 0.015 (0.38) 0.023 (0.58) 0.045 (1.14) 0.065 (1.65) 9 NOTE: Pin spacing is a BASIC dimension; tolerances do not accumulate IL710 Ordering Information and Valid Part Numbers IL 710 T - 3 E TR13 Valid Part Numbers Bulk Packaging Blank = Tube TR7 = 7" Tape and Reel TR13 = 13" Tape and Reel Package Blank = 80/20 Tin/Lead Plating E = RoHS Compliant IL710-1E IL710S-1E IL710T-1E IL710-2 IL710T-2 IL710-2E IL710T-2E Package Type -1 = MSOP -2 = PDIP -3 = 0.15" 8-pin SOIC IL710-3 IL710S-3 IL710T-3 IL710-3E IL710S-3E IL710T-3E Grade Blank = Standard T = High Temperature S = High Speed All MSOP and SOIC parts are available on tape and reel. Base Part Number 710 = Single Channel Product Family IL = Isolators RoHS COMPLIANT 10 IL710 ISB-DS-001-IL710-X March 2012 Changes * Tightened typ. output quiescent supply spec. from 1.7 mA to 1.5 mA. * T-Series quiescent supply specs. tightened to be the same as other grades. ISB-DS-001-IL710-W Changes * Update terms and conditions. ISB-DS-001-IL710-V Changes * Additional changes to MSOP pin spacing on package drawing. ISB-DS-001-IL710-U Changes * Changed MSOP pin spacing on package drawing. ISB-DS-001-IL710-T Changes * Added typical jitter specification at 5V. ISB-DS-001-IL710-S Changes * Added EMC details. ISB-DS-001-IL710-R Changes * IEC 61010 approval for MSOP version. ISB-DS-001-IL710-Q Changes * Added magnetic immunity to 3.3 and 5 volt electrical specifications. * Added diagram showing cross-axis direction. * Added magnetic compatibility to the applications information section. ISB-DS-001-IL710-P Changes * Note on all package drawings that pin-spacing tolerances are non-accumulating; change MSOP pin-spacing dimensions and tolerance accordingly. ISB-DS-001-IL710-O Changes * Corrected PWD spec. on Isolated USB application diagram (p. 8). * Changed lower limit of length on PDIP package drawing and tightened pin-spacing tolerance on MSOP package drawing (p. 9). ISB-DS-001-IL710-N Changes * Changed IL710T output quiescent supply current specifications. ISB-DS-001-IL710-M Changes * Changed ordering information to reflect that devices are now fully RoHS compliant with no exemptions. ISB-DS-001-IL710-L Changes * Eliminated soldering profile chart ISB-DS-001-IL710-K Changes * Edited Profibus application ISB-DS-001-IL710-J Changes * MSOP package, S- and T-Grades added * Order information updated ISB-DS-001-IL710-I Changes * Added MSOP specifications * Updated UL and IEC numbers 11 IL710 Datasheet Limitations The information and data provided in datasheets shall define the specification of the product as agreed between NVE and its customer, unless NVE and customer have explicitly agreed otherwise in writing. All specifications are based on NVE test protocols. In no event however, shall an agreement be valid in which the NVE product is deemed to offer functions and qualities beyond those described in the datasheet. Limited Warranty and Liability Information in this document is believed to be accurate and reliable. However, NVE does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. In no event shall NVE be liable for any indirect, incidental, punitive, special or consequential damages (including, without limitation, lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Right to Make Changes NVE reserves the right to make changes to information published in this document including, without limitation, specifications and product descriptions at any time and without notice. This document supersedes and replaces all information supplied prior to its publication. Use in Life-Critical or Safety-Critical Applications Unless NVE and a customer explicitly agree otherwise in writing, NVE products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical devices or equipment. NVE accepts no liability for inclusion or use of NVE products in such applications and such inclusion or use is at the customer's own risk. Should the customer use NVE products for such application whether authorized by NVE or not, the customer shall indemnify and hold NVE harmless against all claims and damages. Applications Applications described in this datasheet are illustrative only. NVE makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NVE products, and NVE accepts no liability for any assistance with applications or customer product design. It is customer's sole responsibility to determine whether the NVE product is suitable and fit for the customer's applications and products planned, as well as for the planned application and use of customer's third party customers. Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NVE does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer's applications or products, or the application or use by customer's third party customers. The customer is responsible for all necessary testing for the customer's applications and products using NVE products in order to avoid a default of the applications and the products or of the application or use by customer's third party customers. NVE accepts no liability in this respect. Limiting Values Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the recommended operating conditions of the datasheet is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and Conditions of Sale In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NVE hereby expressly objects to applying the customer's general terms and conditions with regard to the purchase of NVE products by customer. No Offer to Sell or License Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export Control This document as well as the items described herein may be subject to export control regulations. Export might require a prior authorization from national authorities. Automotive Qualified Products Unless the datasheet expressly states that a specific NVE product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NVE accepts no liability for inclusion or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NVE's warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NVE's specifications such use shall be solely at customer's own risk, and (c) customer fully indemnifies NVE for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NVE's standard warranty and NVE's product specifications. 12 IL710 An ISO 9001 Certified Company NVE Corporation 11409 Valley View Road Eden Prairie, MN 55344-3617 USA Telephone: (952) 829-9217 Fax: (952) 829-9189 www.nve.com e-mail: iso-info@nve.com (c)NVE Corporation All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. ISB-DS-001-IL710-X March 2012 13