MIC708SNY - Micrel, Inc. - Datasheet.Directory

January 2006 1 MIC706P/R/S/T, MIC708R/S/T

MIC706P/R/S/T, MIC708R/S/T Micrel, Inc.

MIC706P/R/S/T, MIC708R/S/T

µP Supervisory Circuit

General Description

The MIC705, MIC706, MIC707, and MIC708 are inexpensive

mircoprocessor supervisory circuit that monitors power sup-

plies in microprocessor based systems. The circuit functions

include a watchdog timer, microprocessor reset, backup

battery switchover, power failure warning and a debounced

manual reset input.

The MIC705 and MIC706 offer a watchdog timer function

while the MIC707 and MIC708 have an active high reset

output in addition to the active low reset output.

Supply voltage monitor levels of 4.65V and 4.4V are available.

The MIC705 and MIC707 have a nominal reset threshold level

of 4.65V while the MIC706 and MIC708 have a 4.4V nominal

threshold level. When the supply voltage drops below the

respective reset threshold level, /RESET is asserted.

Typical Application

VCC

RESET

µP

RESET

VCC

MIC706

+3.0 or +3.3V (Regulated)

WDI

I/O Line

PFO

Interrupt

PFI

DC Voltage

(Unregulated)

Manual

Reset

WDO

NMI

Features

• 30µA Maximum Supply Current

• Debounced manual reset input is TTL/CMOS

Compatible

• Reset Pulse Width, 200ms

• Watchdog timer, 1.6s (MIC706)

• Precision supply voltage monitor

• Early power fail warning or low battery detect

Applications

• Laptop computers

• Intelligent systems

• Critical microprocessor power monitoring

• Printers

• Computers

• Controllers

Micrel, Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel + 1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com

Ordering Information

Part Number Temperature Range Package

Standard Pb-Free

MIC70_ _N MIC70_ _NY –40ºC to +85ºC 8-Pin PDIP

MIC70_ _M MIC70_ _MY –40ºC to +85ºC 8-Pin SOIC

MIC706P/R/S/T, MIC708R/S/T Micrel, Inc.

MIC706P/R/S/T, MIC708R/S/T 2 January 2006

Pin Conﬁguration

VCC

GND

PFI

WDO

RESET

WDI

PFO

MIC706

PFO

VCC

GND

PFI

RESET

PFO

MIC708

PFO

(RESET for MIC706P)

8-Pin PDIP Package

8-Pin SOIC Package

Pin Description

Pin Number Pin Number Pin Name Pin Function

MIC705/6 MIC707/8

1 1 /MR Manual Reset Input forces /RESET to assert when pulled below 0.8V. An

internal pull-up current of 250µA on this input forces it high when left ﬂoating.

this input can also be driven from TTL or CMOS logic.

2 2 VCC Primary supply input, +5V

3 3 GND IC ground pin, 0V reference

4 4 PFI Power Fail Input. Internally connected to the power fail comparator which

is referenced to 1.25V. The Power Fail Output (/PFO) remains high if PFI

is above 1.25V. PFI should be connected to GND or VOUT if the power fail

comparator is not used.

5 5 /PFO Power Fail Output. The power fail comparator is independent of all other

function on this device.

6 N/A WDI Watch Dog Input. The WDI input monitors microprcessor activity, an internal

watchdog timer resets itself with each transition on the watchdog input. If the

WDIpin is held high or low for longer than the watchog timeout period, /WDO

is forced to active low. the watchdog function can be diabled by ﬂoating the

WDI pin.

N/A 6 N/C Not Internally Connected

7 7 /RESET /RESET is asserted if either VCCgoes below the reset threshold voltage or

by low signal on the manual reset input (/MR). /RESET remains asserted for

one reset timeout period (200ms) after VCC exceeds the reset threshold volt-

age or after the manual reset pin transition from low to high. The watchdog

timer will not assert /RESET unless /WDO is connected to /MR

8 N/A /WDO Output for the Watchdog Timer. The watchdog timer resets itself with each

transition o the watchdog input. If the WDI pin is held high or low for longer

than the watchdog timeout period, /WDO is forced low. /WDO will also be

forced low id VCC is below the reset threshold voltageand will remain low

until VCC returns to a valid level.

N/A 8 RESET RESET is the compliment of /RESET and is asserted if either VCC goes be-

low the reset threshold voltage or by a low signal on the manual reset input

(/MR). RESET is suitable for microprocessor systems that use active high

reset.

January 2006 3 MIC706P/R/S/T, MIC708R/S/T

MIC706P/R/S/T, MIC708R/S/T Micrel, Inc.

Absolute Maximum Ratings(1)

Terminal Voltage

VCC ..........................................................–0.3V to +6.0V

All other inputs .............................–0.3V to (VOUT + 0.3V)

Input Current

VCC, Gnd ................................................................ 25mA

Output Current (all outputs) ........................................ 20mA

Lead Temperature (soldering, 10 sec.) ...................... 300°C

Storage Temperature ................................ –65°C to +150°C

Operating Ratings(2)

Operating Temperature Range

MIC70_N ................................................ –40°C to +85°C

MIC70_M ................................................ –40°C to +85°C

Power Dissipation (PDIP) ........................................ 475mW

Power Dissipation (SOP) ......................................... 400mW

Electrical Characteristics(3)

VCC = 2.70V to 5.5V for MIC70_P/R; VCC = 3.00V to 5.5V for MIC70_S; VCC = 3.15V to 5.5V for MIC70_T;

TA = Operating Temperature Range, bold values indicate –40°C ≤ TA ≤ +85°C; unless noted

Parameter Conditions Min. Typ. Max Units

Operating Voltage Range, VCC 1.4 5.5 V

Supply Current 30 µA

Reset Voltage Threshold MIC70_P/R

MIC70_S

MIC70_T

2.55

2.85

3.00

2.63

2.93

3.08

2.70

3.00

3.15

Reset Threshold Hysteresis 20 mV

Reset Pulse Width, tRS 140 200 280 ms

/RESET Output Voltage

(MIC70_R/S/T)

ISource = 200µA

ISink = 1.2mA

ISink = 50µA, VCC = 1.4V

0.8 × VCC

0.3

RESET Output Voltage

(MIC706P)

ISource = 200µA

ISink = 1.2mA

0.8 × VCC

0.3

RESET Output Voltage

(MIC708R/S/T)

ISource = 200µA

ISink = 500µA

0.8 × VCC

0.3

Watchdog Timeout Period, tWD 1.0 1.6 2.25 sec

WDI Minimum Input Pulse, tWP VIL = 0.4V, VIH = 80% of VCC

VIL = 0.4V, VIH = 80% of VCC > 4.5V

100

WDI Threshold Voltage VIH

VIL

0.7 × VCC

0.6

WDI Input Current WDI = 0V or VCC -1 1 µA

WDO Output Voltage ISource = 200µA

ISink = 500µA

0.8 × VCC

0.3

/MR Pull-Up Current /MR = 0V 20 250 600 µA

/MR Pulse Width, tMR VCC = 4.5V 500

150

/MR Input Threshold VIL

VIH

0.7 × VCC 0.6 V

/MR to Reset Output Delay, tMD 750 ns

PFI Input Threshold 1.2 1.25 1.3 V

PFI Input Current -25 0.01 +25 nA

/PFO Output Voltage ISink = 1.2mA

ISource = 200µA

0.8 × VCC

0.3 V

Note 1. Exceeding the absolute maximum rating may damage the device.

Note 2. The device is not guaranteed to function outside its operating rating.

Note 3. Speciﬁcation for packaged product only.

MIC706P/R/S/T, MIC708R/S/T Micrel, Inc.

MIC706P/R/S/T, MIC708R/S/T 4 January 2006

Timing Diagram

Timing Diagram for Reset

January 2006 5 MIC706P/R/S/T, MIC708R/S/T

MIC706P/R/S/T, MIC708R/S/T Micrel, Inc.

Block Diagram

VTHR*

RESET

GENERATOR

1.25V

WATCHDOG

TIMER

VCC (2)

MR (1)

PFO (5)

RESET (7)

WDO (8)

WDI (6)

PFI (4)

VCC

250•A

(RESET for MIC706P)

* 2.63, 2.93, or 3.08V

MIC705/MIC706 Block diagram

•

VTHR

* 2.63, 2.93, or 3.08V

MIC707/MIC708 Block Diagram

MIC706P/R/S/T, MIC708R/S/T Micrel, Inc.

MIC706P/R/S/T, MIC708R/S/T 6 January 2006

Applications Information

Power Fail Warning

An additional comparator which is independent of the other

functions on the MIC706P/R/S/T is provided for early warning

of power failure. An external voltage divider can be used to

compare unregulated DC to an internal 1.25V reference. The

voltage divider ratio on the input of the power-fail comparator

(PFI) can be chosen so as to trip the power fail comparator a

few milliseconds before VCC falls below the maximum reset

threshold voltage. The output of the power-fail comparator

(/PFO) can be used to interrupt the microprocessor when

used in this mode and execute shut-down procedures prior

to power loss. Hysteresis can be added to this comparator

with external resistors, as is commonly done with any com-

parator. When VCC < VBATT - 1.2V (typ.), the power-fail

comparator is turned off and /PFO is pulled low in order to

conserve power.

1.25V

Unregulated DC

PFO

PFI

Figure 1. Power Fail Comparator

Watchdog Timer

The microprocessor can be monitored by connecting the

WDI pin (watchdog input) to a bus line or an I/O line. If a

transition doesn't occur on the WDI pin with in the watchdog

timeout (Table 1.), the microprocessor is reset. /RESET will

remain asserted for 200ms when this occurs. A minimum

pulse of 100ns or any transition low-to-high or high-to-low

on the WDI pin will reset the watchdog timer. The output of

the watchdog timer (WDO) will remain high, if WDI sees a

valid transition within the watchdog period or if VCC falls

below the reset threshold as the watchdog timer is disabled

when this happens.

Microprocessor Reset

The /RESET pin is asserted whenever VCC falls below the

reset threshold voltage. The reset pin remains asserted for a

period of 200ms after VCC has risen above the reset thresh-

old voltage. The reset timeout period can also be selected

by the end user, see Table 1. The reset function ensures the

microprocessor is properly reset and powers up into a known

condition after a power failure. /RESET will remain valid with

VCC as low as 1.4V and when auxiliary power is connected

to VBATT (VBATT > 2.0V), the reset pin will remain valid with

VCC from 0V to 5.5V.

MIC706P/R/S/T, MIC708R/S/T Micrel, Inc.

MIC706P/R/S/T, MIC708R/S/T 7 January 2006

Package Information

0.260

0.240

0.400

0.370

0.023

0.015

0.110

0.090

0.150

0.120

0.150

0.125

0.035

0.015

0.370

0.300

0.310

0.290

8-Pin PDIP (N)

8-Pin SOIC (M)

MICREL INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA

TEL + 1 (408) 944-0800 FAX + 1 (408) 474-1000 WEB http://www.micrel.com

This information furnished by Micrel in this data sheet is believed to be accurate and reliable. However no responsibility is assumed by Micrel for its use.

Micrel reserves the right to change circuitry and speciﬁcations at any time without notiﬁcation to the customer.

Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can

reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into

the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a signiﬁcant injury to the user. A Purchaser's

use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser's own risk and Purchaser agrees to fully indemnify

Micrel for any damages resulting from such use or sale.