54ABT377 Octal D-Type Flip-Flop with Clock Enable General Description The 'ABT377 has eight edge-triggered, D-type flip-flops with individual D inputs and Q outputs. The common buffered Clock (CP) input loads all flip-flops simultaneously, when the Clock Enable (CE) is LOW. The register is fully edge-triggered. The state of each D input, one setup time before the LOW-to-HIGH clock transition, is transferred to the corresponding flip-flop's Q output. The CE input must be stable only one setup time prior to the LOW-to-HIGH clock transition for predictable operation. n n n n n n n n Features n n n Clock enable for address and data synchronization applications n Eight edge-triggered D flip-flops Buffered common clock See 'ABT273 for master reset version See 'ABT373 for transparent latch version See 'ABT374 for TRI-STATE (R) version Output sink capability of 48 mA, source capability of 24 mA Guaranteed latchup protection High impedance glitch free bus loading during entire power up and power down cycle Non-destructive hot insertion capability Disable time less than enable time to avoid bus contention Standard Microcircuit Drawing (SMD) 5962-9314801 Ordering Code: Military Package Package Description Number 54ABT377J-QML J20A 20-Lead Ceramic Dual-In-Line 54ABT377W-QML W20A 20-Lead Cerpack 54ABT377E-QML E20A 20-Lead Ceramic Leadless Chip Carrier, Type C Connection Diagram Pin Assignment for LCC Pin Assignment for DIP and Cerpack DS100216-11 DS100216-1 Pin Names D0-D7 Description Data Inputs CE Clock Enable (Active LOW) CP Clock Pulse Input Q0-Q7 Data Outputs TRI-STATE (R) is a registered trademark of National Semiconductor Corporation. (c) 1998 National Semiconductor Corporation DS100216 www.national.com 54ABT377 Octal D-Type Flip-Flop with Clock Enable July 1998 Truth Table Mode Select-Function Table Operating Mode Inputs Output CE Dn Qn Load "1" I h H Load "0" I I L Hold h X No Change H X No Change CP (Do Nothing) X H = HIGH Voltage Level h = HIGH Voltage Level one setup time prior to the LOW-to-HIGH Clock Transition L = LOW Voltage Level I = LOW Voltage Level one setup time prior to the LOW-to-HIGH Clock Transition X = Immaterial = LOW-to-HIGH Clock Transition Logic Diagram DS100216-3 Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays. www.national.com 2 Absolute Maximum Ratings (Note 1) DC Latchup Source Current (Across Comm Operating Range) Over Voltage Latchup Storage Temperature -65C to +150C Ambient Temperature under Bias -55C to +125C Junction Temperature under Bias Ceramic -55C to +175C VCC Pin Potential to Ground Pin -0.5V to +7.0V Input Voltage (Note 2) -0.5V to +7.0V Input Current (Note 2) -30 mA to +5.0 mA Voltage Applied to Any Output in the Disabled or Power-Off State -0.5V to +4.75V in the HIGH State -0.5V to VCC Current Applied to Output in LOW State (Max) Twice the rated IOL (mA) -500 mA VCC + 4.5V Recommended Operating Conditions Free Air Ambient Temperature Military Supply Voltage Military Minimum Input Edge Rate Data Input Enable Input -55C to +125C +4.5V to +5.5V (V/t) 50 mV/ns 20 mV/ns DC Electrical Characteristics Symbol Parameter ABT377 Min Typ Units VCC VIH Input HIGH Voltage VIL Input LOW Voltage 0.8 V VCD Input Clamp Diode Voltage -1.2 V Min VOH Output HIGH Voltage V Min VOL Output LOW Voltage IIH Input HIGH Current 2.0 54ABT 2.5 54ABT 2.0 V 54ABT Recognized HIGH Signal 0.55 V Min 5 A Max 7 A Max -5 A Max 5 IBVI Input HIGH Current Conditions Max Recognized LOW Signal IIN = -18 mA IOH = -3 mA IOH = -24 mA IOL = 48 mA VIN = 2.7V (Note 4) VIN = VCC VIN = 7.0V Breakdown Test IIL Input LOW Current -5 VID Input Leakage Test 4.75 IOS Output Short-Circuit Current -100 ICEX ICCH VIN = 0.5V (Note 4) VIN = 0.0V IID = 1.9 A V 0.0 -275 mA Max All Other Pins Grounded VOUT = 0.0V Output High Leakage Current 50 A Max VOUT = VCC Power Supply Current 50 A Max All Outputs HIGH ICCL Power Supply Current 30 mA Max ICCT Maximum ICC/Input 1.5 mA Max All Outputs LOW VI = VCC - 2.1V Data Input VI = VCC - 2.1V 0.3 mA/ Max Outputs Enabled All Others at VCC or GND ICCD Dynamic ICC No Load MHz Outputs Open (Note 3) One bit Toggling, 50% Duty Cycle Note 1: Absolute maximum ratings are values beyond which the device may be damaged or have its useful life impaired. Functional operation under these conditions is not implied. Note 2: Either voltage limit or current limit is sufficient to protect inputs. Note 3: For 8 bits toggling, ICCD < 0.5 mA/MHz. Note 4: Guaranteed but not tested. 3 www.national.com AC Electrical Characteristics Symbol Parameter 54ABT TA = -55C to +125C VCC = 4.5V to 5.5V Units CL = 50 pF Min fmax Max Clock Max 150 MHz Frequency tPLH Propagation Delay 2.2 6.0 tPHL CP to On 2.8 6.8 ns AC Operating Requirements Symbol 54ABT TA = -55C to +125C VCC = 4.5V to 5.5V Parameter Units CL = 50 pF Min ts(H) Setup Time, HIGH 2.0 ts(L) or LOW Dn to CP 2.0 th(H) Hold Time, HIGH 1.8 th(L) or LOW Dn to CP 1.8 ts(H) Setup Time, HIGH 3.0 ts(L) or LOW CE to CP 3.0 th(H) Hold Time, HIGH 1.0 th(L) or LOW CE to CP 1.0 tw(H) Pulse Width, CP, 3.3 tw(L) HIGH or LOW 3.3 Max ns ns ns ns ns Capacitance Typ Units CIN Symbol Input Capacitance Parameter 5 pF COUT (Note 5) Output Capacitance 9 pF Note 5: COUT is measured at frequency f = 1 MHz, per MIL-STD-883B, Method 3012. www.national.com 4 Conditions VCC = 0V, TA = 25C VCC = 5.0V AC Loading DS100216-4 *Includes jig and probe capacitance DS100216-5 FIGURE 1. Standard AC Test Load FIGURE 5. Propagation Delay, Pulse Width Waveforms DS100216-6 FIGURE 2. VM = 1.5V DS100216-9 Input Pulse Requirements FIGURE 6. Setup Time, Hold Time and Recovery Time Waveforms Amplitude Rep. Rate tw tr tf 3.0V 1 MHz 500 ns 2.5 ns 2.5 ns FIGURE 3. Test Input Signal Requirements DS100216-8 FIGURE 4. Propagation Delay Waveforms for Inverting and Non-Inverting Functions 5 www.national.com Physical Dimensions inches (millimeters) unless otherwise noted 20-Lead Ceramic Chip Carrier NS Package Number E20A www.national.com 6 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 20-Lead Ceramic Dual-In-Line Package NS Package Number J20A 20-Lead Ceramic Flatpack NS Package Number W20A 7 www.national.com 54ABT377 Octal D-Type Flip-Flop with Clock Enable LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support 1. Life support devices or systems are devices or sysdevice or system whose failure to perform can be reatems which, (a) are intended for surgical implant into sonably expected to cause the failure of the life support the body, or (b) support or sustain life, and whose faildevice or system, or to affect its safety or effectiveness. ure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Francais Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: sea.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5620-6175 Fax: 81-3-5620-6179 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.