Snap Action Switch V121
Snap Action Switch
V
General Purpose Snap Action Switch
Industry standard design with switching currents of 10A to 21A
Widely used for applications where long life expectancy and
high reliability is required.
Choose from a variety of levers, terminals and operating forces.
Right and Left Barrier options are available for the V-21 and
V-16 models
Heat resistant versions of the V-15 and V-10 are available.
RoHS Compliant
Ordering Information
Model Number Legend
V - - - -
1. Ratings
21: 21 A at 250 VAC
16: 16 A at 250 VAC
2. Contact Gap
None: 1 mm (F gap)
G: 0.5 mm (G gap)
15: 15 A at 250 VAC
11: 11 A at 250 VAC
10: 10 A at 250 VAC
4: 100 gf
7. Maximum Operating Force
6: 400 gf
5: 200 gf
8. Special Purpose
T: Heat resistive
(V-15 and V-10, only)
4. Contact Form
1: SPDT
COM Terminal, Bottom position:
COM Terminal, Side position:
2: SPST-NC
9. Mounting Hole Size
None: 3.1 mm
None: Standard
K: 2.9 mm
3: SPST-NO
4: SPDT
5: SPST-NC
6: SPST-NO
6. Insulation Barrier
None: Without Barrier
R: Right-hand barrier
L: Left-hand barrier
Note: These OF values are for
the pin plunger models.
3. Actuator
None: Pin plunger
1: Short hinge lever
2: Hinge lever
3: Long hinge lever
4: Simulated roller lever
5: Short hinge roller lever
6: Hinge roller lever
5. Terminals
A: Solder terminals
C2: Quick-connect terminal (#187)
C: Quick-connect terminal (#250)
3 4 521 7 8 96
(Barriers available for V-21 and V-16, only)
Note: Consult Omron regarding nomenclature combinations and part numbers
not found in this datasheet.
122 Snap Action Switch V
Available Combinations
Note: 1. : Available model.
Consult OMRON for specific models with standard approval.
List of Models
Thermoplastic Case
21 A (OF: 400 gf)
Note: 1. Add “G” to the part number in the appropriate location to obtain a 0.5 mm contact gap. Add “-K” to the part number in the appropriate
location to obtain 2.9 mm mounting holes. Example: V-21G2-1C6-K
2. Not all combinations are available. Consult Omron regarding nomenclature combinations and part numbers not found in this datasheet.
Thermoplastic case Thermosetting case
ModelV-21V-16V-11V-15 V-10
Rated Current 21 A 16 A 11 A 15 A 10 A
COM
terminal
position
Insulation
Barrier Heat
Resistance
OF
Terminal Symbol
400 gf 400 gf 200 gf 100 gf 400 gf 200 gf 200 gf 100 gf
Bottom No Standard
(80°C)
Solder terminals (A) - - - ❍❍❍❍❍❍❍
Quick-connect
terminals (#187)(C2) - - - ❍❍❍❍❍❍❍
Quick-connect
terminals (#250)(C) ❍❍❍❍❍❍❍❍
Heat
resistant
(150°C)
Solder terminals (A) - - - - - - - - - - - - ❍❍❍❍
Quick-connect
terminals (#187)(C2) - - - - - - - - - - - - ❍❍❍❍
Quick-connect
terminals (#250)(C) - - -- - -- - -- - -- - -- - -- - -- - -
Yes Standard
(80°C)
Solder terminals (A) - - - ❍❍- - - - - - - - - - - - - - -
Quick-connect
terminals (#187)(C2) - - - ❍❍- - - - - - - - - - - - - - -
Quick-connect
terminals (#250)(C) ❍❍❍- - - - - - - - - - - - - - -
Side No Standard
(80°C)
Solder terminals (A) - - - - - - - - - - - - ❍❍❍❍
Quick-connect
terminals (#187)(C2) - - - - - - - - - - - - ❍❍❍❍
Quick-connect
terminals (#250)(C) - - - - - - - - - - - - - - - - - - - - -
Common
terminal
position Contact
form Terminal style Actuator
Bottom SPDT Quick-connect
(#250) (C)
V-21-1C6 V-21-1CR6 V-21-1CL6
SPST-NCV-21-2C6 V-21-2CR6 V-21-2CL6
SPST-NOV-21-3C6 V-21-3CR6 V-21-3CL6
SPDT V-211-1C6 V-211-1CR6 V-211-1CL6
V-212-1C6 V-212-1CR6 V-212-1C6
V-213-1C6 V-213-1CR6 V-213-1CL6
V-214-1C6 V-214-1CR6 V-214-1CL6
V-215-1C6 V-215-1CR6 V-215-1CL6
V-216-1C6 V-216-1CR6 V-216-1CL6
Without barrier
Without barrier
Right-hand barrier
Left-hand barrier
Pin plunger
Short hinge lever
Hinge lever
Long hinge lever
Simulated roller lever
Short hinge roller lever
Hinge roller lever
Snap Action Switch V123
16 A (OF: 200 gf)
11 A (OF: 100 gf)
Note: 1. Add “G” to the part number in the appropriate location to obtain a 0.5 mm contact gap. Add “-K” to the part number in the appropriate
location to obtain 2.9 mm mounting holes. Examples: 1) V-16G3-1C25-K 2) V-11G-1A4-K
2. Not all combinations are available. Consult Omron regarding nomenclature combinations and part numbers not found in this datasheet.
Common
terminal
position Contact
form Terminal style Actuator
Bottom SPDT A V-16-1A5 V-16-1AR5 V-16-1AL5
C2 V-16-1C25 V-16-1C2R5 V-16-1C2L5
CV-16-1C5 - - - - - -
SPST-NCA V-16-2A5 V-16-2AR5 V-16-2AL5
C2 V-16-2C25 V-16-2C2R5 V-16-2C2L5
CV-16-2C5 - - - - - -
SPST-NOA V-16-3A5 V-16-3AR5 V-16-3AL5
C2 V-16-3C25 V-16-3C2R5 V-16-3C2L5
CV-16-3C5 - - - - - -
SPDT A V-161-1A5 V-161-1AR5 V-161-1AL5
C2 V-161-1C25 V-161-1C2R5 V-161-1C2L5
CV-161-1C5 - - - - - -
AV-162-1A5 V-162-1AR5 V-162-1AL5
C2 V-162-1C25 V-162-1C2R5 V-162-1C2L5
CV-162-1C5 - - - - - -
AV-163-1A5 V-163-1AR5 V-163-1AL5
C2 V-163-1C25 V-163-1C2R5 V-163-1C2L5
CV-163-1C5 - - - - - -
AV-164-1A5 V-164-1AR5 V-164-1AL5
C2 V-164-1C25 V-164-1C2R5 V-164-1C2L5
CV-164-1C5 - - - - - -
AV-165-1A5 V-165-1AR5 V-165-1AL5
C2 V-165-1C25 V-165-1C2R5 V-165-1C2L5
CV-165-1C5 - - - - - -
AV-166-1A5 V-166-1AR5 V-166-1AL5
C2 V-166-1C25 V-166-1C2R5 V-166-1C2L5
CV-166-1C5 - - - - - -
Without barrier
Without barrier
Right-hand barrier
Pin plunger
Short hinge lever
Hinge lever
Long hinge lever
Simulated roller lever
Short hinge roller lever
Hinge roller lever
Common
terminal
position Contact form Terminal style Actuator
Bottom SPDT A V-11-1A4
C2 V-11-1C24
CV-11-1C4
AV-111-1A4
C2 V-111-1C24
CV-111-1C4
AV-112-1A4
C2 V-112-1C24
CV-112-1C4
AV-113-1A4
C2 V-113-1C24
CV-113-1C4
AV-114-1A4
C2 V-114-1C24
CV-114-1C4
AV-115-1A4
C2 V-115-1C24
CV-115-1C4
AV-116-1A4
C2 V-116-1C24
CV-116-1C4
Without barrier
Pin plunger
Short hinge lever
Hinge lever
Long hinge lever
Simulated roller lever
Short hinge roller lever
Hinge roller lever
124 Snap Action Switch V
Thermosetting Case
Standard models - 15 A / 10 A
Note: 1. For SPST-NC and SPST-NO with levers consult Omron.
2. Not all combinations are available. Consult Omron regarding nomenclature combinations and part numbers not found in this datasheet.
Heat Resistant Models (Up to 150°C) - 15 A / 10A
Note: 1. Add “G” to the part number in the appropriate location to obtain a 0.5 mm contact gap. Add “-K” to the part number in the appropriate
location to obtain 2.9 mm mounting holes. Add “C2” to the part number in the appropriate location to obtain versions with #187 quick-
connect terminals. Example: 1) V-15G1-1C25-T-K
2. Not all combinations are available. Consult Omron regarding nomenclature combinations and part numbers not found in this datasheet.
Common
terminal
position
Contact
form Terminal style Actuator 15 A 10 A
200 gf 200 gf 100 gf
Bottom SPDT A V-15G-1A5-K V-10G-1A5-K V-10G-1A4-K
C2 V-15G-1C25-K V-10G-1C25-K V-10G-1C24-K
CV-15G-1C5-K —
SPST-NCA V-15G-2A5-K V-10G-2A5-K V-10G-2A4-K
C2 V-15G-2C25-K V-10G-2C25-K V-10G-2C24-K
SPST-NOA V-15G-3A5-K V-10G-3A5-K V-10G-3A4-K
C2 V-15G-3C25-K V-10G-3C25-K V-10G-3C24-K
CV-15G-3C5-K
Side SPDT A V-15G-4A5-K V-10G-4A5-K V-10G-4A4-K
SPST-NCV-15G-5A5-K V-10G-5A5-K V-10G-5A4-K
SPST-NOV-15G-6A5-K V-10G-6A5-K V-10G-6A4-K
Bottom SPDT A V-15G1-1A5-K V-10G1-1A5-K V-10G1-1A4-K
C2 V-15G1-1C25-K V-10G1-1C25-K V-10G1-1C24-K
AV-15G2-1A5-K V-10G2-1A5-K V-10G2-1A4-K
C2 V-15G2-1C25-K V-10G2-1C25-K V-10G2-1C24-K
AV-15G3-1A5-K V-10G3-1A5-K V-10G3-1A4-K
C2 V-15G3-1C25-K V-10G3-1C25-K V-10G3-1C24-K
AV-15G4-1A5-K V-10G4-1A5-K V-10G4-1A4-K
C2 V-15G4-1C25-K V-10G4-1C25-K V-10G4-1C24-K
AV-15G5-1A5-K V-10G5-1A5-K V-10G5-1A4-K
C2 V-15G5-1C25-K V-10G5-1C25-K V-10G5-1C24-K
AV-15G6-1A5-K V-10G6-1A5-K V-10G6-1A4-K
C2 V-15G6-1C25-K V-10G6-1C24-K
Common
terminal
position
Contact
form Terminal style Actuator 15 A 10 A
200 gf 100 gf
Bottom SPDT Solder Terminals
(A)
V-15-1A5-T V-10-1A4-T
V-151-1A5-T V-101-1A4-T
V-152-1A5-T V-102-1A4-T
V-153-1A5-T V-103-1A4-T
V-154-1A5-T V-104-1A4-T
V-155-1A5-T V-105-1A4-T
V-156-1A5-T V-106-1A4-T
Pin plunger
Short hinge lever
Hinge lever
Long hinge lever
Simulated roller lever
Short hinge roller lever
Hinge roller lever
Pin plunger
Short hinge lever
Hinge lever
Long hinge lever
Simulated roller lever
Short hinge roller lever
Hinge roller lever
Snap Action Switch V125
Specifications
Ratings (reference values)
Note: 1. The above current values are the normal current values of models with a contact gap of 1 mm (gap F), which vary with the normal current
values of models with a contact gap of 0.5 mm (gap G).
2. Inductive load has a power factor of 0.4 min. (AC) and a time constant of 7 ms max. (DC).
3. Lamp load has an inrush current of 10 times the steady-state current.
4. Motor load has an inrush current of 6 times the steady-state current.
5.
The ratings values apply under the following test conditions: Ambient temperature: 20
±
2
°
C, Ambient humidity: 65
±
5%, Operating frequency: 30 operations/min
Approved Standards
UL1054 (File No. E41515)
CSA C22.2 No.55 (File No. LR21642)
EN 61058-1 (File No. 129608, VDE approval)
Testing conditions: 5E4 (50,000 operations), T105 (0°C to 105°C)
EN 61058-1 (File No. T9451451, TÜV Rheinland approval)
Testing conditions: 5E4 (50,000 operations), T85 (0°C to 85°C)
Type Rated voltage Non-inductive load Inductive load
Resistive load Lamp load Inductive load Motor load
NC NO NC NO NC NO NC NO
V-21 250 VAC 21 A 3 A 12 A 4 A
8 VDC
30 VDC
125 VDC
250 VDC
21 A
14 A
0.6 A
0.3 A
5 A
5 A
0.1 A
0.05 A
12 A
12 A
0.6 A
0.3 A
7 A
5 A
0.1 A
0.05 A
V-16 250 VAC 16 A 2 A 10 A 3 A
8 VDC
30 VDC
125 VDC
250 VDC
16 A
10 A
0.6 A
0.3 A
4 A
4 A
0.1 A
0.05 A
10 A
10 A
0.6 A
0.3 A
6 A
4 A
0.1 A
0.05 A
V-15 250 VAC 15 A 2 A 10 A 3 A
8 VDC
30 VDC
125 VDC
250 VDC
15 A
10 A
0.6 A
0.3 A
4 A
4 A
0.1 A
0.05 A
10 A
10 A
0.6 A
0.3 A
6 A
4 A
0.1 A
0.05 A
V-11 250 VAC 11 A 1.5 A 6 A 2 A
8 VDC
30 VDC
125 VDC
250 VDC
11 A
6 A
0.6 A
0.3 A
3 A
3 A
0.1 A
0.05 A
6 A
6 A
0.6 A
0.3 A
3 A
3 A
0.1 A
0.05 A
V-10 250 VAC 10 A 1.5 A 6 A 2 A
8 VDC
30 VDC
125 VDC
250 VDC
10 A
6 A
0.6 A
0.3 A
3 A
3 A
0.1 A
0.05 A
6 A
6 A
0.6 A
0.3 A
3 A
3 A
0.1 A
0.05 A
Rated voltage V-21 V-16 V-15 V-11 V-10
125 VAC 21 A, 1/2 HP 16 A, 1/2 HP 15 A, 1/2 HP 11 A, 1/3 HP 10 A, 1/3 HP
250 VAC
125 VDC 0.6 A
250 VDC 0.3 A
Rated voltage V-21 V-16 V-11
250 VAC 20 (4) A 16 (4) A 11 (3) A
Rated voltage V-15 V-10
250 VAC 15 A 10 A
250 VDC 0.3 A
126 Snap Action Switch V
Characteristics
Note: 1. Data shown are of initial value.
2. The dielectric strength shown is measured using a separator between the switch and metal mounting plate.
3. For pin plunger models, the above values apply for use at both the free position and total travel position. For lever models, they apply at
the total travel position.
4. For testing conditions, contact your OMRON sales representative.
Contact Specifications
Note: Minimum applicable loads are indicated by N standard reference values. This value represents the failure rate at a 60% 60) reliability level
(JIS C5003). The equation λ60=0.5 x 10-6 / operations indicates that a failure rate of 1/2,000,000 operations can be expected at a reliability
level of 60%
Operating speed 0.1 mm to 1 m/s (plunger models)
Operating frequency Mechanical: 600 operations/minute, max.
Electrical: 30 operations/minute, max.
Insulation resistance 100 MΩ min. (at 500 VDC)
Contact resistance 15 mΩ max.
Dielectric strength (see note 2) 1,000 VAC, 50/60 Hz for 1 min between terminals of the same polarity
V-21, V-16 and V-11:
2,000 VAC, 50/60 Hz for 1 min between current-carrying metal parts and ground, and between
each terminal and non-current-carrying metal parts
V-15 and V-10:
1,500 VAC, 50/60 Hz for 1 min between current-carrying metal parts and ground, and between
each terminal and non-current-carrying metal parts
Vibration resistance (see note 3) Malfunction: 10 to 55 Hz, 1.5-mm double amplitude
Shock resistance (see note 3) Destruction: 1,000 m/s2 (approx. 100G) max.
Malfunction: V-21/V-16/V-15: 300 m/s2 (approx. 30G) max.
V-11/V10: 200 m/s2 (approx. 20G) max.
Life expectancy Mechanical: 50,000,000 operations min. (60 operations/minute)
Electrical: V-21/V-16/V-15: 100,000 operations min. (30 operations/minute)
(V-15 heat resistive: 20,000 operations min. (30 ops/minute))
V-11/V-10: 300,000 operations min. (30 operations/minute)
(V-10 heat resistive: 50,000 operations min. (30 ops/minute))
Degree of protection IEC IP40
Degree of protection against electric shock Class I
Proof tracking index (PTI) 175
Ambient operating temperature
-25
°
C to 80
°
C (at 60% RH max.) with no icing
-25
°
C to 150
°
C for heat resistive models (at 60% RH max.) with no icing.
Ambient operating humidity 85% max. (for 5°C to 35°C)
Weight Approx. 6.2 g (plunger models)
Item V-21 V-16 V-15 V-11 V-10
Contact Specification Rivet
Material Silver alloy Silver
Gap
(standard value) 1 mm (F gap type) or 0.5 mm (G gap type)
Inrush current NC50 A max. 40 A max. 36 A max. 24 A max.
NO
Minimum applicable load 160 mA at 5 VDC
Snap Action Switch V127
Engineering Data
Contact Form
* The SPST-NC and SPST-NO contact form types listed in the
ordering information tables are for Pin Plunger models only.
For information concerning lever models consult Omron.
Barrier direction (V-21 and V-16)
Mounting Holes
All switches may be panel mounted using M3 mounting screws with
plane washers or spring washers to securely mount the switch.
Tighten the screws to a torque of 0.39 to 0.59 N·m.
Mechanical service life Electrical service life
(Pin plunger models) (Pin plunger models)
V-21/-16/-15/-10
Number of operations (x10 )
6
200
100
50
10
0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 (1.6) 1.8
Ambient temperature: 20±2°C
Ambient humidity: 65±5%
Without load
Operating frequency: 600 operations/min
V-10 (0.98 N {100 gf}),
V-11
V-10 (1.96 N
{200 gf})
V-15
V-16
V-21
OT rated value
Full stroke
OT (mm)
V-21/-16/-15
Operating frequency: 60 operations/min
cosφ = 1, 250 VAC
5
2
1
0.5
0.3
0.1
0 4 8 1216202428
V-21
V-15
V-16
Switching current (A)
Number of operations (x10 )
6
5
2
1
0.5
0.3
0.1
00.5 1 2 3 4 5 6 7 8 9 10 11 12
V-10
V-11
V-11/-10
Switching current (A)
Ambient temperature: 20±2°C
Ambient humidity: 65±5%
Operating frequency: 60 operations/min
cosφ = 1, 250 VAC
Number of operations (x10 )
6
Common
terminal
position
Contact form
SPDT SPST-NC* SPST-NO*
Bottom type
Side type
Right-hand Barrier Left-hand Barrier
Two, 3.1-dia. mounting holes or
M3 screw holes
10.3 ± 0.1
22.2 ±0.1
128Snap Action Switch V
Dimensions
Terminals
Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions
2. The following table is for the SPDT contact specifications. Two terminals will be available for SPST-NO or SPST-NC contact specifications.
For terminal positions, refer to the above Contact Form
3. Right-angle PCB terminal type is available with some models (not shown). Drawings will be provided if requested.
D5: Pins at right angles, to the right
D6: Pins at right angle, to the left
Terminal type Solder Terminal
(A) Quick-connect Terminal
(#187) (C2) Quick-connect Terminal
(#250) (C)
COM
bottom position
COM
side position
Terminal
dimensions
t = 0.5
Three, solder terminals
(10)
2.9
(6.5)
(5.5)
t = 0.5
Three, quick-connect
terminals (#187)
(10)
2.9
(6.5)
(5.5)
t = 0.8
Three, quick-connect
terminals (#250)
(12.0)
3.2
(7.7)
(4.9)
(10)
2.4
(6.5)
(5.5)
(10)
2.4
(6.5)
(5.5)
(12.0)
3.6
(7.7)
(4.9)
1.6 dia.2.4 dia.
4.75±0.1
6.35
3.2 (see note)
Note: Indicates the length to the
center of the 1.6-dia. holes
1.6-dia. terminal hole
4.75±0.1
3.2
6.35
1.65-dia. terminal hole
6.35±0.1
3.95
8.1
Snap Action Switch V129
Dimensions and Operating Characteristics
Thermoplastic Case Models
Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions
2.
The following illustrations and drawings are for quick-connect terminals (#250) (terminals C). V models also incorporate terminals A and C2,
which are omitted from the following drawings. Refer to Terminals section for the dimensions of these terminals.
3. The @ in the model number is for the terminal code.
4.
The illustrations for V-21, V-16 and V-11 show a hole size of 3.1 mm. V-21, V-16 and V-11 models with a suffix “K” have a hole size of 2.9 mm.
5. The operating characteristics are for operation in the A direction ( ).
Pin Plunger Models
(Without Barrier)
V-21-1 6
V-16-1 5
V-11-1 4
3.1+0.13
–0.03 dia. holes
3.1+0.13
–0.03
3.4±0.15 dia. t=0.8
Three, quick-connect
terminals (#250)
20.2±0.25
2.8
1.6
2.8
10.3±0.1
PT
OP
22.2±0.1 2.8 (12.0)
27.8
39.8±0.8
2.8
8.4
15.9 19.1
0.6
4.2
2.8
10.3
(With Right-hand Barrier)
V-21-1 R6
V-16-1 R5
3.1+0.13
–0.03 dia. holes
3.1+0.13
–0.03
3.4±0.15 dia. t=0.8
Three, quick-connect
terminals (#250)
20.2±0.25
2.8 1.6
2.8
10.3±0.1
PT
OP
22.2±0.1 2.8 (12.0)
27.8
39.8±0.8
40.2
2.8
15.9
8.4 19.1
21.9
0.6 4.2 2.8
0.6
10.3
A
A
(With Left-hand Barrier)
V-21-1 L6
V-16-1 L5
3.1+0.13
–0.03 dia. holes
3.1+0.13
–0.03
3.4±0.15 dia.
t=0.8
Three, quick-connect
terminals (#250)
2.8 0.6
4.2
0.6
10.3
2.8
19.1
15.9
8.4
21.9
1.6
20.2±0.25
2.8 2.8
(12.0) 2.8
27.8
39.8±0.8
22.2±0.1
40.2
10.3±0.1
PT
OP
A
Characteristics V-21-1@6 V-16-1@5
OF max. 400 gf 200 gf
RF min. 80 gf 50 gf
PT max. 1.2 mm
OT min. 1.0 mm
MD max. 0.4 mm
OP 14.7 ± 0.4 mm
Characteristics V-11-1@4 V-11-1@5
OF max. 100 gf 200 gf
RF min. 20 gf 50 gf
PT max. 1.2 mm
OT min. 1.0 mm
MD max. 0.4 mm
OP 14.7 ± 0.4 mm
130 Snap Action Switch V
Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions
2.
The following illustrations and drawings are for quick-connect terminals (#250) (terminals C). V models also incorporate terminals A and C2,
which are omitted from the following drawings. Refer to Te r m i n a l s section for the dimensions of these terminals.
3. The @ in the model number is for the terminal code.
4.
The illustrations for V-21, V-16 and V-11 show a hole size of 3.1 mm. V-21, V-16 and V-11 models with a suffix “K” have a hole size of 2.9 mm.
5. The operating characteristics are for operation in the A direction ( ).
Short Hinge Lever Models
Hinge Lever Models
Long Hinge Lever Models
V-211-1 6
V-161-1 5
V-111-1 43.1+0.13
–0.03 dia. holes
3.1+0.13
–0.03
3.4±0.15 dia.
t = 0.5
(see
note)
t=0.8
Three, quick-connect
terminals (#250)
22.1
8.1
PT
OP
2.8
10.3±0.1
2.8 (12.0)
27.8
22.2±0.1
39.8±0.8
1.6
2.8
8.4 15.9 19.1
0.6 2.8
4.3
10.3
Note: Stainless-steel lever
A
Characteristics V-211-1@6 V-161-1@5 V-111-1@4
OF max. 400 gf 200 gf 100 gf
RF min. 50 gf 50 gf 15 gf
PT max. 1.6 mm
OT min. 0.8 mm
MD max. 0.6 mm
OP 15.2 ± 0.5 mm
3.1+0.13
–0.03 dia. holes
3.1+0.13
–0.03
3.4±0.15 dia.
t = 0.5
(see note)
t=0.8
Three, quick-connect
terminals (#250)
35.6±0.8
8.1 1.6
PT
OP
2.8
10.3±0.1
22.2±0.1 (12.0)
2.8
27.8
39.8±0.8
2.8
15.9
8.4 19.1
0.6 2.8
4.3
10.3
V-212-1 6
V-162-1 5
V-112-1 4
Note: Stainless-steel lever
A
Characteristics V-212-1@6 V-162-1@5 V-112-1@4
OF max. 250 gf 125 gf 60 gf
RF min. 25 gf 14 gf 6 gf
PT max. 4.0 mm
OT min. 1.6 mm
MD max. 1.5 mm
OP 15.2 ± 1.2 mm
3.1+0.13
–0.03 dia. holes
3.1+0.13
–0.03
3.4±0.15 dia.
t = 0.5 (see note)
t=0.8
Three, quick-connect
terminals (#250)
59.4±0.8
PT
OP
2.8
10.3±0.1
22.2±0.1 (12.0)
2.8
27.8
39.8±0.8
2.8
8.4 15.9 19.1
0.6 2.8
4.3
10.3
V-213-1 6
V-163-1 5
V-113-1 4
Note: Stainless-steel lever
1.6
A
Characteristics V-213-1@6 V-163-1@5 V-113-1@4
OF max. 130 gf 70 gf 35 gf
RF min. 12 gf 6 gf - - -
PT max. 9.0 mm
OT min. 2.0 mm 3.2 mm
MD max. 2.8 mm
OP
15.2
±
2.6 mm
15.2 mm
+2.6
3.2
Snap Action Switch V131
Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions
2.
The following illustrations and drawings are for quick-connect terminals (#250) (terminals C). V models also incorporate terminals A and C2,
which are omitted from the following drawings. Refer to Terminals section for the dimensions of these terminals.
3. The @ in the model number is for the terminal code.
4.
The illustrations for V-21, V-16 and V-11 show a hole size of 3.1 mm. V-21, V-16 and V-11 models with a suffix “K” have a hole size of 2.9 mm.
5. The operating characteristics are for operation in the A direction ( ).
Simulated Roller Lever Models
Short Hinge Roller Lever Models
Hinge Roller Lever Models
V-214-1 6
V-164-1 5
V-114-1 43.1+0.13
–0.03 dia. holes
3.1+0.13
–0.03
3.4±0.15 dia.
t = 0.5
(see note)
t=0.8
Three, quick-connect
terminals (#250)
3.5R
32.6±0.8
8.1 1.6
PT
OP 2.8
10.3±0.1
22.2±0.1 (12.0)
2.8
27.8
39.8±0.8
0.6 3.48.2
10.3
Note: Stainless-steel lever
2.8
15.9 19.1
8.4
A
Characteristics V-214-1@6 V-164-1@5 V-114-1@4
OF max. 250 gf 125 gf 60 gf
RF min. 25 gf 14 gf 6 gf
PT max. 4.0 mm
OT min. 1.6 mm
MD max. 1.5 mm
OP 18.7 ± 1.2 mm
Note: 1. Stainless-steel lever
2. Oilless polyacetar resin roller
V-215-1 6
V-165-1 5
V-115-1 4
3.1
+0.13
–0.03
dia. holes
3.1
+0.13
–0.03
3.4±0.15 dia.
t = 0.5
(see
note 1) 4.8 dia. × 4.8
(see note 2)
t=0.8
Three, quick-connect
terminals (#250)
20.1
8.1 1.6
PT
OP
2.8
10.3±0.1
22.2±0.1 2.8 (12.0)
27.8
39.8±0.8
2.8
8.4 15.9 19.1
0.6 5.1
10.3
A
Characteristics V-215-1@6 V-165-1@5 V-115-1@4
OF max. 480 gf 240 gf 120 gf
RF min. 50 gf 50 gf 15 gf
PT max. 1.6 mm
OT min. 0.8 mm
MD max. 0.6 mm
OP 20.7 ± 0.6 mm
V-216-1 6
V-166-1 5
V-116-1 43.1 +0.13
–0.03 dia. holes
3.1+0.13
–0.03
3.4±0.15 dia.
t = 0.5
(see note 1) 4.8 dia. × 4.8
(see note 2)
t=0.8
Three, quick-connect
terminals (#250)
34.0±0.8
8.1 1.6PT
OP 2.8
10.3±0.1
22.2±0.1 (12.0)
2.8
27.8
39.8±0.8
2.8
19.1
0.6
5.1
10.3
15.9
8.4
Note: 1. Stainless-steel lever
2. Oilless polyacetar resin roller
A
Characteristics V-216-1@6 V-166-1@5 V-116-1@4
OF max. 250 gf 125 gf 60 gf
RF min. 25 gf 14 gf 6 gf
PT max. 4.0 mm
OT min. 1.6 mm
MD max. 1.5 mm
OP 20.7 ± 1.2 mm
132 Snap Action Switch V
Thermosetting Case Models
Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions
2.
The following illustrations are for quick-connect terminals (#250) (terminals C). Refer to Terminals section for the dimensions of other terminals.
3. The @ in the model number is for the terminal code.
4.
The illustrations show models with a suffix “K”, which have a hole size of 2.9 mm. Omit the “K” to obtain models with hole size = 3.1 mm.
5. The operating characteristics are for operation in the A direction ( ).
Pin Plunger Models
Short Hinge Lever Models
Hinge Lever Models
Long Hinge Lever Models
V-15G-1 5-K
V-10G-1 5-K
V-10G-1 4-K
2.9
+0.13
–0.03
dia. holes
3.1
+0.13
–0.03
3.4±0.15 dia.
t=0.5
Three, solder
terminals
20.2±0.25
2.8
2.8
10.3±0.1
PT
OP
22.2±0.1 2.8
27.8 (10)
37.8±0.8
15.9 18.8
4.2 2.8
10.3
A
Characteristics V-15G-1@5-K
V-10G-1@5-K V-10G-1@4-K
OF max. 200 gf 100 gf
RF min. 50 gf 20 gf
PT max. 1.2 mm
OT min. 1.3 mm
MD max. 0.3 mm
OP 14.7 ± 0.4 mm
V-15G1-1 5-K
V-10G1-1 5-K
V-10G1-1 4-K
2.9
+0.13
–0.03
dia. holes
3.1
+0.13
–0.03
3.4±0.15 dia.
t = 0.5 (see note)
t=0.5
Three, solder terminals
22.1
8.1
PT
2.8
22.2±0.1 2.8
27.8 (10)
37.8±0.8
15.9 18.8
4.3 2.8
10.3
OP 10.3±0.1
Note: Stainless-steel lever
A
Characteristics V-15G1-1@5-K
V-10G1-1@5-K V-10G1-1@4-K
OF max. 200 gf 100 gf
RF min. 50 gf 15 gf
PT max. 1.5 mm
OT min. 1.0 mm
MD max. 0.5 mm
OP 15.2 ± 0.5 mm
V-15G2-1 5-K
V-10G2-1 5-K
V-10G2-1 4-K 2.9+0.13
–0.03 dia. holes
3.1+0.13
–0.03
3.4±0.15 dia.
t = 0.5 (see note)
t=0.5
Three, solder terminals
35.6±0.8
8.1
PT
OP
2.8
10.3±0.1
22.2±0.1 2.8
27.8
(10)
37.8±0.8
15.9 18.8
4.3 2.8
10.3
Note: Stainless-steel lever
A
Characteristics V-15G2-1@5-K
V-10G2-1@5-K V-10G2-1@4-K
OF max. 125 gf 60 gf
RF min. 14 gf 6 gf
PT max. 3.3 mm
OT min. 2.3 mm
MD max. 0.8 mm
OP 15.2 ± 1.2 mm
15.2 mm
+2.6
3.2
V-15G3-1 5-K
V-10G3-1 5-K
V-10G3-1 4-K
2.9
+0.13
–0.03
dia. holes
3.1
+0.13
–0.03
3.4±0.15 dia.
t = 0.5 (see note)
t=0.5
Three, solder terminals
22.2±0.1
27.8
2.8
(10)
15.9 18.8
10.3±0.1
OP
PT
8.1
4.3
2.8
10.3
37.8±0.8
59.4±0.8
2.8
Note: Stainless-steel lever
A
Characteristics V-15G3-1@5-K
V-10G3-1@5-K V-10G3-1@4-K
OF max. 70 gf 35 gf
RF min. 6 gf - - - gf
PT max. 9.0 mm 7.6 mm
OT min. 3.0 mm 3.2 mm
MD max. 2.0 mm
OP 15.2 ± 2.6 mm
Snap Action Switch V133
Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions
2.
The following illustrations are for quick-connect terminals (#250) (terminals C). Refer to Te r m i n a l s section for the dimensions of other terminals.
3. The @ in the model number is for the terminal code.
4.
The illustrations show models with a suffix “K”, which have a hole size of 2.9 mm. Omit the “K” to obtain models with hole size = 3.1 mm.
5. The operating characteristics are for operation in the A direction ( ).
Simulated Roller Lever Models
Short Hinge Roller Lever Models
Hinge Roller Lever Models
Accessories
Refer to the “V/VX/D3C Common Accessories” datasheet for information regarding VAL, VAM and VAV external actuators (sold separately).
V-15G4-1 5-K
V-10G4-1 5-K
V-10G4-1 4-K
3.5R
2.9+0.13
–0.03 dia. holes
3.1+0.13
–0.03
3.4±0.15 dia.
t = 0.5 (see note)
t=0.5
Three, solder terminals
22.2±0.1
27.8
2.8
(10)
15.9 18.8
10.3±0.1
OP
PT
8.1
4.3
2.8
10.3
37.8±0.8
32.6±0.8
2.8
Note: Stainless-steel lever
A
Characteristics V-15G4-1@5-K
V-10G4-1@5-K V-10G4-1@4-K
OF max. 125 gf 60 gf
RF min. 14 gf 6 gf
PT max. 3.3 mm
OT min. 2.3 mm
MD max. 0.8 mm
OP 18.7 ± 1.2 mm
4.8 dia. × 4.8 (see note 2)
2.9+0.13
–0.03 dia. holes
3.1+0.13
–0.03
3.4±0.15 dia.
t = 0.5 (see note 1)
22.2±0.1
27.8
2.8
(10)
15.9 18.8
10.3±0.1
OP
PT
8.1
5.1
10.3
37.8±0.8
20.1
2.8
V-15G5-1 5-K
V-10G5-1 5-K
V-10G5-1 4-K
Note: 1. Stainless-steel lever
2. Oilless polyacetar resin roller
A
t=0.5
Three, solder terminals
Characteristics V-15G5-1@5-K
V-10G5-1@5-K V-10G5-1@4-K
OF max. 240 gf 120 gf
RF min. 50 gf 15 gf
PT max. 1.5 mm
OT min. 1.0 mm
MD max. 0.5 mm
OP 20.7 ± 0.6 mm
V-15G6-1 5-K
V-10G6-1 5-K
V-10G6-1 4-K
4.8 dia. × 4.8 (see note 2)
2.9
+0.13
–0.03
dia. holes
3.1
+0.13
–0.03
3.4±0.15 dia.
t = 0.5 (see note 1)
22.2±0.1
27.8
2.8
(10)
15.9 18.8
10.3±0.1
OP
PT
8.1
5.1
10.3
37.8±0.8
34.0±0.8
2.8
Note: 1. Stainless-steel lever
2. Oilless polyacetar resin roller
A
t=0.5
Three, solder terminals
Characteristics V-15G6-1@5-K
V-10G6-1@5-K V-10G6-1@4-K
OF max. 125 gf 60 gf
RF min. 14 gf 6 gf
PT max. 3.3 mm
OT min. 2.3 mm
MD max. 0.8 mm
OP 20.7 ± 1.6 mm
134 Snap Action Switch V
Precautions
Be sure to read the precautions and information common to all Snap Action and Detection Switches, contained in the Technical User’s Guide,
“Snap Action Switches, Technical Information” for correct use.
Correct Use
Terminal Connection
To solder the lead to the solder terminal, apply a soldering iron rated
at 60 W max. quickly (within 5 seconds) with the actuator at the free
position.
Note that applying a soldering iron for too long a time or using one
that is rated at more than 60 W may degrade the switch characteris-
tics.
Use an appropriate mating connector for #187 or #250 quick connect
terminals.
Specifications Approved by TÜV Rheinland
According to EN61058-1
Appropriate Cable Size (mm2)
Operation
Make sure that the operating body pushes the switch actuator with
an adequate force when the switch is to be operated, and that it does
not touch the actuator when the switch is released.
Do not change the operating position by modifying the actuator.
Do not use the switch in a application where the operating speed is
extremely slow or the actuator is set in the midpoint between the free
position and operating position.
Install the pin plunger switch so that the operating force is applied in
alignment with the stroke of the actuator. The switch should be set so
that its stroke is in the range of 60 to 90% of the rated OT (minimum
value) when the switch has been operated.
Cautions
Insulation Distance
According to EN61058-1, the minimum insulation thickness for this
switch should be 1.1 mm and minimum clearance distance between
the terminal and mounting plate should be 1.0 mm. If the insulation
distance cannot be provided in the product incorporating the switch,
either use a switch with insulation barrier or use a separator to
ensure sufficient insulation distance.
Model Solder terminal
V-10 0.75, 1.25, 2.0
V-15 1.25, 2.0
Snap Action Switch V
MEMO
Snap Action Switch V
OMRON ON-LINE
Global - http://www.omron.com
USA - http://www.components.omron.com
Cat. No. X303-E-1 Printed in USA
OMRON ELECTRONIC
COMPONENTS LLC
55 E. Commerce Drive, Suite B
Schaumburg, IL 60173
847-882-2288
11/10 Specifications subject to change without notice
All sales are subject to Omron Electronic Components LLC standard terms and conditions of sale, which
can be found at http://www.components.omron.com/components/web/webfiles.nsf/sales_terms.html
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Omron:
V-15G-1C25-K V-15G-1C26-K V-10-7A5 V-10G5-1C25-K V-15G5-1C25-K V-15G5-1C26-K V-10G3-1C24-K V-
15G3-1C26-K V-15G3-1C25-K V-10G-1A4K V-15G6-1C26-K V-15G6-1C25-K V-15G4-1C25-K V-10G-1C24-K V-
15-1A5 V-15G2-1C25-K V-10G2-1C24-K V-15G2-1C26-K V-10G2-1C25-K V-15-1B5 V-16G-3C26 V-215-1CR6 V-
15G-2C26-K V-15G-1C5-K V-15G-1B5-K V-15G-1E5-K V-15G-2C25-K V-15G-3A5-K V-15G-3C25-K V-15G-3C5-K
V-15G-4A5-K V-15G-6A5-K V-15G1-1C25-K V-15G1-1E5-K V-15G2-1A5-K V-15G2-1E5-K V-15G3-1A5-K V-
15G3-1B5-K V-15G4-1A5-K V-15G5-1A5-K V-15G5-1B5-K V-15G6-1A5-K V-15G6-1B5-K V-10G-1A5-K V-10G-
1B5-K V-10G-2C25-K V-10G-3C25-K V-10G1-1C25-K V-10G2-1A5-K V-10G3-1C25-K V-10G4-1C25-K V-10G5-
1A5-K V-10G5-1B5-K V-10G6-1A5-K V-10G-1B4-K V-10G-1E4-K V-10G-2C24-K V-10G-3C24-K V-10G-4A4-K V-
10G1-1A4-K V-10G1-1C24-K V-10G1-1E4-K V-10G2-1A4-K V-10G2-1B4-K V-10G3-1A4-K V-10G4-1A4-K V-10G4-
1C24-K V-10G4-1B4-K V-10G5-1A4-K V-10G5-1B4-K V-10G6-1A4-K V-10G6-1B4-K V-15-3B6-K V-01G-1C23-K
V151C5 V-16G-3C25-L V-11-1B5 V-16G88K-3CR5 V-15-3C6-K V-15-1A6 V-16G-3C25 V-16G-3C25-K V-10G-
1C25-K V-10G5-1C24-K V-10G6-1C24-K V-15G-1A5-K V-15-2C26-K V-15G-1B6-K V-10-1A4 V-10-1A4-T V-10-
1B4 V-10-1B5 V-10-1C25 V-10-1C25-K V-10-1E25 V-102-1A4 V-102-1A4-T V-103-1A4 V-103-1C24-T V-103-
1C25-T