1
0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC
FH41 Series
2010.9
■Features
1. Compatibility with impedance control, shield
FFC
The FH41 series is equipped with a GND exclusive terminal
and available for connection with impedance control, shield
FFC.
2.Differential impedance 100Ω±10%
The FH41 series features a terminal design considering
impedance control, and making high speed transmission
possible.
3.Highly reliable connection, tough structure
The FH41 series follows the structure of the proven FH28
series, and achieves:
- High reliability thanks to the FFC positioning mechanism
- Reliable connection operation and no unlocking thanks to the
durable structure.
4.One-finger operation of the actuator
Proven (in several other Hirose's connectors!) Flip-Lock
rotating actuator assures reliable mechanical and electrical
connection with FPC, confirming it with a definite tactile feel.
5.Board placement with automatic equipment
Flat upper surface and tape and reel packaging facilitate
vacuum pick-up and placement.
Standard reel packaging contains 2,500 connectors.
6.Halogen-free *
*As defined by IEC61249-2-21
Br-900ppm maximum, Cl-900ppm maximum,
Cl + Br combined-1,500ppm maximum
＊=^\]"heZZYhZg^Va^ciZg[VXZiZX]cdad\n
 [dg^bV\ZigVchb^hh^dc
THine Electronics, Inc.
Next-generation chipset (V-by-One®HS*)
Compatible connector
'#*bb
+#'bb
(-bb
H^\cVaXdciVXiXdccZXi^dcVgZV
<C9XdciVXiXdccZXi^dcVgZV
FFC
Space saving (68 pos. shown)
Signal contact
0.5mm pitch
Ground contact
2.5mm pitch
figure.1
figure.2
figure.3
2
FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC
■Specifications
Ratings
Current rating 0.5 A(Note1)
Voltage rating 50 Vrms AC
O perating temperature range:
-40 to +85°C (Note 2)
O perating humidity range:
Relative humidity 90% max. (No condensation)
S torage temperature range:
-10 to +50°C (Note 3)
S torage humidity range:
Relative humidity 90% max. (No condensation)
Recommended FPC Thickness 0.3 ±0.05 mm, Gold plated contact pads (GND plate:t=0.5±0.05mm,tinÐplateing)
Item Specifi cation Conditions
1. Insulation
resistance 500 Mø min. 100 V DC
2.Withstanding voltage
No fl ashover or insulation breakdown 150 Vrms AC / one minute
3.Contact resistance 100 mø max.
* Including FFC conductor resistance 1 mA, AC max (AC: 1kHz)
4.Durability Contact resistance: 100 mø max.
No damage, cracks, or parts dislocation 20 cycles
5.Vibration
No electrical discontinuity of 1µs or longer
Contact resistance: 100 mø max.
No damage, cracks, or parts dislocation
Frequency: 10 to 55 Hz, single amplitude of 0.75mm,
10 cycles in each of the 3 directions
6.Shock
No electrical discontinuity of 1µs or longer
Contact resistance: 100 mø max.
No damage, cracks, or parts dislocation
Acceleration of 981m/s2 6 ms duration, sine halfwave,
3 cycles in each of the 3 axis
7.Humidity
(Steady state)
Contact resistance: 100 mø max.
Insulation resistance: 50 Mø min.
No damage, cracks, or parts dislocation
96 hours at 40°C and humidity of 90 to 95%
8.Temperature cycle
Contact resistance: 100 mø max.
Insulation resistance: 50 Mø min.
No damage, cracks, or parts dislocation
Temperature : -40°C →+15°C to +35°C →+85°C →
+15°C to +35°C
Time: 30 →2 to 3 →30 →2 to 3 minutes
5 cycles
9. Resistance to
soldering heat
No deformation of components affecting performance
Refl ow: At the recommended temperature profi le
Manual soldering: 350°C ±5°C for 5 seconds
Note 1. When passing the current through all of the contacts, use 70% of the rated current.
Note 2. Includes temperature rise caused by current fl ow.
Note 3. The term "storage" refers to products stored for a long period prior to mounting and use.
The operating temperature and humidity range covers the non-conducting condition of installed connectors in storage, shipment or
during transportation after board mounting.
Note 4. Information contained in this catalog represents general requirements for this Series.
Contact us for the drawings and specifi cations for a specifi c part number shown.
■Materials
Part Material Finish Remarks
Insulator LCP Color:Gray UL94V-0
Color:Black
Contacts Phosphor bronze Gold plated
---------
Pure tin refl ow plated
Metal fi ttings Brass
■Ordering information
FH 41 − 50S − 0.5 SH (05)
❶❷ ❸ ❹❺ ❻
❺ SH : SMT horizontal mounting type
❻ Plating specifi cations :(05)…Gold plated
❶ Series name : FH
❷ Series No.: 41
❸ Number of positions : 28 to 68
❹ Contact pitch : 0.5mm
3
FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC
■Connector Dimensions
*#)*
<
*#%*
%#&'
%#&'
&
:
9
8
%#&*
'#*
(9^bZch^dc[dg;;8deZc^c\
Cd#d[XdciVXih
8Vk^inCd#
+#'
'#*
%#- %#'*
'
)#,
Unit : mm
Part Number CL No. Number of contacts
No. of Contacts(GND contacts)
CDEFG
FH41-28S-0.5SH(05) 580-2208-1-05 28 5 18 13.5 10 14.57 15.95
FH41-40S-0.5SH(05) 580-2205-3-05 40 8 24 19.5 17.5 20.57 21.95
FH41-50S-0.5SH(05) 580-2204-0-05 50 10 29 24.5 22.5 25.57 26.95
FH41-68S-0.5SH(05) 580-2202-5-05 68 13 38 33.5 30 34.57 35.95
Note1.Tape and reel packaging (2,500 pieces/reel).
Order by number of reels.
Note 1. The coplanarity of each terminal lead within specifi ed dimension is 0.1 mm Max.
2. Packaged on tape and reel only. Check packaging specifi cation.
3. Slight variations in color of the plastic compounds do not affect form, fi t or function of the connector.
4. After refl ow, the terminal plating may change color, however this does not represent a quality issue.
4
FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC
■Recommended PCB mounting pattern and metal mask dimensions
■Recommended FFC Dimensions
&¤%#%*
%#*¤%#%*
'#*¤%#%*
%#(¤%#%(AVcYeViiZgc
%#(¤%#%(AVcYeViiZgc
%#)¤%#%(
:¤%#%*
9¤%#%*
=¤%#%*
+#+¤%#&
%#+*¤%#%*
&#'¤%#%*
AVcYeViiZgc
&#**¤%#%*
+#(*¤%#%*
%#'¤%#%Metalmask
&¤%#%*Metalmask
%#'*¤%#%(Metalmask
GZXdbbZcYZYbZiVabVh`i]^X`cZhhi2%#&
EaZVhZdkZgaVeh]^ZaYeaViZdc\gdjcYeaViZ#CdiZ
H]^ZaYVgZV
<gdjcYeaViZ
&,#,B6M
%#*¤%#%*
%#(¤%#%*
*#*B>C
(#-¤%#&
'#+¤%#&
&#.¤%#&
*#*B>C
%#&B>C
'#,¤%#*
'#'¤%#*
%#*¤%#& %#*¤%#%*
%#(¤%#%(
?¤%#&
@¤%#%,
9¤%#%*
'"G%#'bVm
'"G%#'bVm
'"G%#'
'"G%#'
1
&
Unit : mm
Part Number CL No. Number of contacts
No. of Contacts(GND contacts)
HJK
FH41-28S-0.5SH(05) 580-2208-1-05 28 5 16 15.7 14.5
FH41-40S-0.5SH(05) 580-2205-3-05 40 8 22 21.7 20.5
FH41-50S-0.5SH(05) 580-2204-0-05 50 10 27 26.7 25.5
FH41-68S-0.5SH(05) 580-2202-5-05 68 13 36 35.7 34.5
Note1.Tape and reel packaging (2,500 pieces/reel).
Order by number of reels.
5
FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC
■Recommended FFC construction
Note 1 Please overlap shield plate on ground plate.
Material Name Material
thickness(µm) thickness(µm)
Shielding Material
Conouctiye Adhesive Polyester Type
Copper Film (Tin Plated) 70
Adhesive Acrylic Type 24
Base Material Polyester Type 12
Adhesive Acrylic Type 24
Insulated Layer Polyester Type ２５
Adhesive Polyester Type ３５
Soft Copper Film
(Nickel Under Plated / Gold Plated) 35 35
Adhesive Polyester Type 35 35
Insulated Layer Polyester Type 25 25
Adhesive Polyester Type 30 30
Siiffener Polyester Type 188 188
Total 503 313
1
1
1
1
6
FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC
●Embossed Carrier Tape Dimensions
■Packaging Specification
●Reel Dimensions
Ｌ
Ｃ
Ｃ
Ｌ
IVeZl^Yi]d[('bbb^c#IVeZl^Yi]d[')bbbVm#
9^gZXi^dcd[jcgZZa^c\
9^gZXi^dcd[jcgZZa^c\
F
&#+)/KVXjbe^X`jeVgZV
E
)¤%#&
'¤%#&
&'¤%#&
%#(
'#.
G
A¤%#(
B¤%#&
&#,*¤%#&
,#(*
*#,*
C¤%#&
*#,*
,#(*
&#,*¤%#&
A¤%#(
G
'#.
%#( &'¤%#&
'¤%#&
)¤%#&
E
&#+)/KVXjbe^X`jeVgZV
F
C¤%#&
&&#*
 %
＋%#&
&&#*
 %
＋%#&
IgV^aZg
Edgi^dcZfj^eeZYl^i]XdccZXidgh
:bWdhhZYXVgg^ZgiVeZ
AZVYZg)%%bbb^c
IdeXdkZgiVeZ
&%:beinXdbedcZciXdbeVgibZcihb^c&):beinXdbedcZciXdbeVgibZcihb^c
¢&(
¢-%
¢(-%
H/Djih^YZ
I/>ch^YZ
Unit : mm
Part Number CL No. Number of contacts
No. of Contacts(GND contacts)
LMNPQRST
FH41-28S-0.5SH(05) 580-2208-1-05 28 5 32 28.4 14.2 18.3 17 15.7 37.4 33.4
FH41-40S-0.5SH(05) 580-2205-3-05 40 8 44 40.4 20.2 24.3 23 21.7 49.4 45.4
FH41-50S-0.5SH(05) 580-2204-0-05 50 10 44 40.4 20.2 29.3 28 26.7 49.4 45.4
FH41-68S-0.5SH(05) 580-2202-5-05 68 13 56 52.4 26.2 38.3 37 35.7 61.4 57.4
7
FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC
■Temperature Profile
HRS test condition
Solder method :Refl ow, IR/hot air
Environment :Room air
Solder composition :Paste, 96.5%Sn/3.0%Ag/0.5%Cu
(Senju Metal Industry, Co., Ltd.'s Part
Number:M705-221CM5-32-10.5)
Test board :Glass epoxy 30mm×60mm×0.8mm thick
Land dimensions :0.3mm×0.65mm, 0.3mm×1.2mm
Metal mask :0.25×0.65, 0.2×0.1mm thick
The temperature profi les shown are based on the above conditions.
In individual applications the actual temperature may vary,
depending on solder paste type, volume / thickness and board size /
thickness. Consult your solder paste and equipment manufacturer for
specifi c recommendations.
MAX250℃
HiVgi
I^bZHZXdcYh
25℃
（
+%hZX#
）（
+%hZX#
）
.%s&'%hZX#
EgZ]ZVi^c\ hdaYZg^c\
0
50
100
150 150℃
200℃
230℃
200
250
IZbeZgVijgZ
8
FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC
Operation Precautions
1. FFC insertion procedure.
Connector installed on the board.
❶ Lift up the actuator. Use thumb or index finger
❶
Do not force the actuator to open beyond its fully open
position. Do not use any type of tool to open the actuator.
❷ Fully insert the FFC in the connector parallel to
mounting surface, with the exposed conductive traces
facing down.
❷ Do not forcefully bend the FFC upward. Consult FFC
manufacturer for the
recommended bend radiuses.
❸ Rotate down the actuator until firmly closed. It is
critical that the inserted FFC is not moved and remains
fully inserted.
❸ For connectors with multiple contacts, such as 80 pos.
rotate down the actuator pushing at both ends.
2.FFC removal
Fully open the actuator.
Carefully withdraw the FFC exercising caution not to
deform or damage it.
❹ Load to FFC
Be very careful not to apply any force to the connector
directly after inserting FFC.
Otherwise, the connector may become unlocked or
the FFC may break.
In particular, design the FFC layout with care not to
bend it sharply upward in a vertial direction near the
insertion opening.
Fix the FFC when loads are applied to it continuously.
■Operation and Precautions
110°
①
Insert the cable straight
and obliquely from
above.
②Slightlypullthecable
tomakesurethetabs
arefirmlysecured.
③ Closetheactuator.
Ride on a left guide
Ride on a right guide
Correct insertion
Do not close the actuator as the cables ride on.
Do not move the cables back and forth and around as
the cables ride on the guide when the actuator is closed.
9
FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC
Operation Precautions
1. How to insert
Insert the cable into the interspace between the mold walls
() at both ends of entrance where the connector is
inserted and the guide walls( )at both ends of
interior connector so the cable tabs are properly located.
❷
Avoid “ride on”
Avoid insertion so the cables ride on any guide. Be
sure NOT to close the actuator as the cables ride on
any guide. It may cause conduction failure.
2. Precautions when mating /un-mating
❶
Avoid insertion in diagonal direction.
Do not insert the cable in diagonal direction.
A part of the connector may touches the contacts
resulting in deformation of the contacts.
Insert the cable straight into the connector and hook
the cable tabs with the guide.
After insertion, slightly pull the cables to make sure
the cable tabs are fi rmly secured. No removal of the
cable means correct insertion.
In the event it is locked as the cables ride on a guide,
absolutely avoid moving the cable. In this case, open
the actuator and re-insert the cable as instructed in “
1.How to insert”
■Precautions (mating/un-mating FFC with the retention tabs)
10
FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC
NOTES :
11
FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC
NOTES :
12
FH41 Series●0.5mm pitch, 2.5mm above the board,high speed transmission connector for shielded FFC
USA:
HIROSE ELECTRIC (U.S.A.), INC. Headquarters
2688 Westhills Court, Simi Valley, CA 93065-6235
Phone : 1-805-522-7958
Fax : 1-805-522-3217
http://www.hiroseusa.com
HONG KONG:
HIROSE ELECTRIC HONGKONG TRADING CO., LTD.
Unit 1102 A&B, Energy Plaza, 92 Granville Road,
Tsim Sha Tsui East, Kowloon
Phone : 852-2803-5338
Fax : 852-2591-6560
http://www.hirose-hongkong.com.hk
CHINA:
HIROSE ELECTRIC CO., LTD. BEIJING REPRESENTATIVE OFFICE
A1001, Ocean International Center, Building 56# East 4th
Ring Middle Road, Chao Yang District, Beijing, 100025
Phone : 86-10-5165-9332
Fax : 86-10-5908-1381
http://www.hirose-china.com.cn
TAIWAN:
HIROSE ELECTRIC TAIWAN CO., LTD.
103 8F, No.87, Zhengzhou Rd., Taipei
Phone : 886-2-2555-7377
Fax : 886-2-2555-7350
http://www.hirose-taiwan.com.tw
GERMANY:
HIROSE ELECTRIC EUROPE B.V. GERMAN BRANCH
Herzog-Carl-Strasse 4 D-73760 Ostfildern
(Scharnhauser Park)
Phone : 49-711-4560-02-1
Fax : 49-711-4560-02-299
http://www.hirose.de
SINGAPORE:
HIROSE ELECTRIC CO., LTD.
10 Anson Road #26-16 International Plaza 079903
Phone : 65-6324-6113
Fax : 65-6324-6123
http://www.hirose-singapore.com.sg
THE NETHERLANDS:
HIROSE ELECTRIC EUROPE B.V.
Hogehillweg #8 1101 CC Amsterdam Z-O
Phone : 31-20-6557460
Fax : 31-20-6557469
http://www.hiroseeurope.com
UK:
HIROSE ELECTRIC EUROPE B.V. UK BRANCH
First Floor, St Andrews House, Caldecotte Lake
Business Park, Milton Keynes MK7 8LE
Phone : 44-1908-369060
Fax : 44-1908-369078
http://www.hirose.co.uk
USA:
HIROSE ELECTRIC (U.S.A.), INC. Detroit Office (Automotive)
37677 Professional Center Drive, Suite #100C
Livonia, MI 48154
Phone : 1-734-542-9963
Fax : 1-734-542-9964
http://www.hiroseusa.com
USA:
HIROSE ELECTRIC (U.S.A.), INC. North California Office
20400 Stevens Creek Blvd., Ste 250, Cupertino,
CA 95014
Phone : 1-408-253-9640
Fax : 1-408-253-9641
http://www.hiroseusa.com
CHINA:
HIROSE ELECTRIC (SHANGHAI) CO., LTD.
1501-02, Cross Tower Building, 318 Fuzhou Road,
Huang Pu District, Shanghai 200001
Phone : 86-21-6391-3355
Fax : 86-21-6335-0767
http://www.hirose-china.com.cn
CHINA:
HIROSE ELECTRIC CO., LTD. SHENZHEN OFFICE
Room 09-13, 19/F, Office Tower Shun Hing Square, Di Wang Commercial Centre
5002, ShenNanDong Road, ShenZhen City, Guangdong Province, 518008
Phone : 86-755-8207-0851
Fax : 86-755-8207-0873
http://www.hirose-china.com.cn
KOREA:
HIROSE KOREA CO., LTD.
1261-10, Jeoungwhang-Dong, Shihung-City,
Kyunggi-Do 429-450
Phone : 82-31-496-7000,7124
Fax : 82-31-496-7100
http://www.hirose.co.kr
The contents of this catalog are current as of date of 09/2010. Contents are subject to change without notice for the purpose of improvements.
5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN
PHONE: 81-3-3491-5300, FAX: 81-3-3495-5230
http://www.hirose.com
http://www.hirose-connectors.com
®
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Hirose Electric:
FH41-28S-0.5SH(05) FH41-40S-0.5SH(05) FH41-50S-0.5SH(05) FH41-68S-0.5SH(05) FH41-30S-0.5SH(05)
FH41-31S-0.5SH(05) FH41-40S-0.5SH FH41-50S-0.5SH FH41-15S-0.5SH(05) FH41-50S-0.5SH(28) FH41-40S-
0.5SH(99) FH41-30S-0.5SH(99) FH41-31S-0.5SH(99) FH41-28S-0.5SH(99) FH41-50S-0.5SH(99) FH41-68S-
0.5SH(99)