case for cool-running temperatures and rugged-construction, allowing the ESCs to be used in a wide-range of harsh environments and
commercial/industrial applications. �The new series also comes pre-loaded with�the latest production firmware, including these new, market-
leading technologies:
Regenerative Braking � active braking during motor deceleration phase, providing instantaneous response to the flight controller commands
and matched-response to acceleration profiles (less �float� during flight).
Temperature-Controlled Synchronous Rectification � new proprietary algorithm for smooth-running motors at low-throttle and improved,
faster response under high-peak loads; all while significantly increasing flight-time efficiency and reducing operating temperatures (also termed
"active-freewheeling").
Dynamic Timing and Startup Power � optimally-tuned for smooth and precision-controlled startup throughout the full-range of XF UAS
Brushless Motors (no hesitation, stuttering, or response lag).
Increased Drive and Throttle Frequency Resolution � high-accuracy, linear throttle response throughout full-range of operation control.
Motor Synchronization � factory-calibrated ESCs for consistent throttle control and frequency-matched start-up protocols.
The UAS HVC series is compatible with 3S - 12S LiPo (55V Max) power systems - allowing for the next level of performance and
efficiency for your UAS and Multi-Rotor applications. �� In addition, the UAS HVC series includes active anti-spark circuitry, protecting
the integrity and life-span of the critical connectors upon each initial plug-in and system power-up.
The series is tuned and optimized for the KDE Direct XF Multi-Rotor Brushless Motor Series , for simple plug-and-play operation. No additional
throttle calibration is required for most applications and settings are factory programmed.
ESCs include 200�C, 13 AWG silicone-wire power leads and 14 AWG silicone-wire motor leads with dual ?4.0mm and ?3.5mm 24K matching
Bullet Connectors.
SPECIFICATIONS
Programming : Proprietary Algorithm, 600Hz Refresh, Dynamic Advance Timing
Features : Active Anti-Spark Circuit, Aluminum 6061-T6 Case
Includes :
Two (2) KDE Direct XF ? 3.5mm 24K Bullet Connectors (Pair, KDEXF-BC35 )
Two (2) KDE Direct XF ?4.0 mm 24K Bullet Connectors (Pair, KDEXF-BC40 )
Full Specifications :
Refresh Rate 600 Hz (50 - 600Hz Adaptive)
Maximum Peak Current 95 A (5 s)
Maximum Peak Power 4,220 W (5 s)
Maximum Continuous Current* 55+ A (180 s)
Maximum Continuous Power* 2,445+ W (180 s)
Maximum Efficiency > 98%
Voltage Range 11.1 V (3S) - 50.4 V (12S)
Internal BEC None (Opto-Isolation)
Maximum RPM 360,000 rpm (2-Pole)
PWM Rate Adaptive Dynamic Algorithm
Advance Timing 22� - 30� Dynamic Algorithm
ESC Size 35 mm (W) x 72 mm (L)
ESC Weight 68 g (92 g with Wires/Bullets)
Power Leads 13 AWG, 200�C
Motor Leads 14 AWG, 200�C
ESC Control Lead 22 AWG, 3-Wire JR (W-R-B)
ESC Programming Lead 22 AWG, 3-Wire JR (O-R-B)
Power Connects ?3.5 / ?4.0 mm Matched Pair
Motor Connects ?4.0 mm Female
*: ESC requires consistent airflow (5 mph or greater) across the heatsink to maintain maximum continuous current and power ratings during operation,
specified at full-load condition (100% throttle). Increasing airflow or adding additional cooling can further increase the capabilities of the controller and extend the
lifespan of the critical internal components.
TECHNICAL MEDIA
KDEXF-UAS55HVC Design Geometry Dimensions Specification Sheet (PDF)
XF UAS ESC Series Instruction Manual REVPR06 (PDF)
XF UAS HVC ESC Series Technology Review (PDF)