FTR-K1 SERIES POWER RELAY 1 POLE - 16A Relay FTR-K2 Series n FEATURES SPST-NO High insulation Insulation distance: minimum 6mm between coil and contact Dielectric strength: 4KV Surge strength: 10KV l TV-5 rating l Heat resistance, flammability Class B (130 C) wire class, flammability 94V-0 l Cadmium free contact for eco-program l Safety standards UL, CSA, VDE approved UL/CSA TV-5 rating approved l Flux proof sealing, RTII l RoHS compliant Please see page 6 for more information l l n PARTNUMBER INFORMATION [Example] FTR-K2 (a) A (b) K (c) 012 T - OK (d) (e) (f) (a) Relay type (b) Contact configuration FTR-K2 : FTR-K2-Series A : 1 form A (SPST-NO) (c) Coil type K : Standard type (530mW) (d) Coil rated voltage (e) Contact material / TV type (f) Special type 012 : 5.....48 VDC Coil rating table at page 3 T : Silver-tin oxide / TV-5 None : Standard (TV-5) TH : TV-8 rating Actual marking does not carry the type name : "FTR" E.g.: Ordering code: FTR-K2AK012T Actual marking: K2AK012T 1 FTR-K1 SERIES FTR-K2 SERIES n SPECIFICATION Item Contact Data Life FTR-K2AK ( ) T Configuration 1 form A (SPST-NO) Construction Single Material Silver tin oxide (AgSnO2) Resistance (initial) Max. 100m at 1A, 6VDC Contact rating (resistive) 250VAC / 30VDC / 16A Max. carrying current 16A Max. switching voltage 400VAC / 300VDC Max. switching power 4,000VA / 480W Min. switching load* 100mA, 5VDC Mechanical Min. 2 x 106 operations Electrical Coil Data Timing Data Insulation Min. 100 x 103 operations AC contact rating Min. 100 x 103 operations Lamp load (TV-5) Min. 25 x 103 operations Rated power (20 C) 530mW Operate power (20 C) 260mW Operating temperature range -40 C to +70 C (no frost) Operate (at nominal voltage) Max. 15ms (without bounce) Release (at nominal voltage) Max. 5ms (without bounce) Resistance (initial) Min. 1,000M at 500VDC Dielectric strength Surge strength Open contacts 1,000VAC (50/60Hz) 1min Contacts to coil 4,000VAC (50/60Hz) 1min Coil to contacts 10,000V / 1.2 x 50s standard wave Clearance 6mm Creepage 6mm EN61810-1, VDE0435 Other DC contact rating Vibration resistance Shock Voltage 250V Pollution degree 3 Material group III a Category B / 250V Misoperation>1us 10 to 55 to 10Hz single amplitude 0.75mm Endurance 10 to 55 to 10Hz single amplitude 0.75mm Misoperation>1us 200m/s (11 1ms) Endurance 1,000m/s (6 1ms) Weight Approximately 13g Sealing Flux proof (RT II) * Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. Care shall be taken on the heat generated on PC board when maximum carrying current exceeds 10A. Please perform the confirmation test with actual conditions. 2 FTR-F4 SERIES FTR-K1 SERIES FTR-K2 SERIES n COIL RATING Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must ReleaseVoltage (VDC) * 003 3 17 2.1 0.15 005 5 47 3.5 0.25 006 6 68 4.2 0.3 009 9 155 6.3 0.45 012 12 270 8.4 0.6 018 18 610 12.6 0.9 024 24 1,110 16.8 1.2 048 48 4,400 33.6 2.4 Rated Power (mW) 530 Note: All values in the table are valid for 20C and zero contact current. * Specified operate values are valid for pulse wave voltage. Please use at rated coil voltage. Please refer to characteristic data and set up adequate voltage in case of use at over voltage. n SAFETY STANDARDS Type Compliance Contact rating UL UL 508 Flammability: UL 94-V0 (plastics) E63614 16A, 30VDC (resistive) 15A, 140VAC (resistive) 10A, 277VAC (resistive) 1/2 HP,125VAC (UL), 1/3 HP 125VAC (CSA) TV-5, 120 VAC , TV-8, 120VAC Pilot duty: A300 (UL), C300 (CSA) CSA C22.2 No. 14 LR 40304 VDE IEC/EN61810-1 EN60065 clause 14.6.1 16A, 250 VAC (cos=1) 8A, 250 VAC cos=0.4) 16A, 30 VDC (0ms) 250VAC 5/80A inrush CQC GB/T21711-1 GB15092-1 03001008195 <FTR-K2AK( )T> 16A 250VAC 3 FTR-K1 SERIES FTR-F4 SERIES FTR-K2 SERIES n CHARACTERISTIC DATA (Characteristic data is not guaranteed value but measured values of samples from production line.) 4 FTR-K1 SERIES FTR-F4 SERIES FTR-K2 SERIES n DIMENSIONS l Dimensions l Schematics l PC board mounting hole layout (BOTTOM VIEW) Unit: mm * Dimensions of the terminals do not include thickness of pre-solder. * Tolerance of PC board mounting hole layout : 0.1 unless otherwise specified Cautions * All values mentioned in this datasheet are provided under ideal conditions. Please perform the confirmation test before actual use. * Reflow soldering is prohibited. * Do not use relays in the atmosphere with sulfide gas, chloride gas or nitric oxide. Contact resistance may increase. * Do not use silicon or silicon-containing product or materials near relays. It may cause contact failure. 5 FTR-K1 SERIES FTR-F4 SERIES FTR-K2 SERIES RoHS Compliance and Lead Free Information 1. General Information l l l l All relays produced by Fujitsu Components are compliant with RoHS directive 2011/65/EU including amendments. Cadmium as used in electrical contacts is exempted from the RoHS directives. As per Annex III of directive 2011/65/EU. All relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/downloads/MICRO/fcai/relays/lead-free-letter.pdf Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. 2. Recommended Lead Free Solder Condition l Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder Condition: Pre-heating: maximum 120C within 90 sec. Soldering: dip within 5 sec. at 255C 5C solder bath Relay must be cooled by air immediately after soldering Solder by Soldering Iron: Soldering Iron Temperature: Duration: 30-60W maximum 350-360C maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 6 FTR-F4 SERIES FTR-K1 SERIES FTR-K2 SERIES Fujitsu Components International Headquarter Offices Japan FUJITSU COMPONENT LIMITED Shinagawa Seaside Park Tower 19F, 12-4, Higashi-shinagawa 4-chome, Shinagawa-ku, Tokyo,140-0002, Japan Tel: (81-3) 3450-1682 Fax: (81-3) 3474-2385 Email: fcl-contact@cs.jp.fujitsu.com Web: www.fujitsu.com/jp/fcl/ Asia Pacific FUJITSU COMPONENTS ASIA, LTD. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components North and South America FUJITSU COMPONENTS AMERICA, INC 2290 North First Street, Suite 212 San Jose, CA 95131, USA Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: us.fujitsu.com/components China FUJITSU ELECTRONIC COMPONENTS (SHANGHAI) CO., LTD. Unit 4306, InterContinental Center 100 Yu Tong Road, Shanghai 200070, China Tel: (86-21) 3253 0998 Fax: (86-21) 3253 0997 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components Europe FUJITSU COMPONENTS EUROPE B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: www.fujitsu.com/uk/components Hong Kong FUJITSU COMPONENTS HONG KONG CO., LTD Unit 506, Inter-Continental Plaza No.94 Granville Road, Tsim Sha Tsui, Kowloon, Hong Kong Tel: (852) 2881-8495 Tex: (852) 2894-9512 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components/ Korea FUJITSU COMPONENTS KOREA LIMITED Alpha Tower #403, 645 Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, 13524 Korea Tel: (82) 31-708-7108 Fax: (82) 31-709-7108 Email: fcal@sg.fujitsu.com www.fujitsu.com/sg/products/devices/components/ (c)2018 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users' own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. April 24th, 2018 7