GS9064 SD SDI Adaptive Cable Equalizer DATA SHEET DESCRIPTION * SMPTE 259 and SMPTE 344 compliant The GS9064 is a second-generation high-speed bipolar integrated circuit designed to equalize and restore signals received over 75 co-axial cable at data rates from 143Mb/s up to 540Mb/s. The GS9064 is designed to support SMPTE 344M and SMPTE 259M and is optimized for performance at 270Mb/s. * automatic cable equalization * supports DVB-ASI at 270Mb/s * typical maximum equalized length of Belden 1694A cable at 270Mb/s is 350m * 50 differential output (with internal 50 pull-ups) * cable length indicator * output mute based on maximum cable length adjust or manual override * Pb-free and Green * single 3.3V power supply operation * operating temperature range: 0C to +70C * pin compatible with HDLINXTM II GS1524 multirate SDI adaptive cable equalizer APPLICATIONS * SMPTE 259M Coaxial Cable Serial Digital Interfaces The GS9064 features DC restoration to compensate for the DC content of SMPTE pathological test patterns, and incorporates a Cable Length Indicator (CLI) that provides a linear indication of the amount of cable being equalized. A voltage programmable mute threshold (MCLADJ) is included to allow muting of the GS9064 output when a selected cable length is reached. This feature allows the GS9064 to distinguish between low amplitude SDI signals and noise at the input of the device. The CD/MUTE pin provides an indication of the GS9064 mute status in addition to functioning as a mute control input. The output of the GS9064 may be forced to an active or a mute condition by applying a voltage to the CD/MUTE pin. CABLE LENGTH INDICATOR/ADJUSTOR CARRIER DETECT MUTE MCLADJ CLI CD/MUTE BYPASS SDI SDI EQUALIZER DC RESTORE OUTPUT SDO SDO AGC GS9064 FUNCTIONAL BLOCK DIAGRAM Revision Date: June 2006 Document No. 22212 - 3 GENNUM CORPORATION P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3 Tel. +1 (905) 632-2996 Fax. +1 (905) 632-5946 E-mail: info@gennum.com www.gennum.com GS9064 KEY FEATURES TABLE OF CONTENTS 1. PIN OUT .......................................................................................................................................... 3 1.1 PIN ASSIGNMENT................................................................................................................ 3 1.2 PIN DESCRIPTIONS .............................................................................................................. 3 2. ELECTRICAL CHARACTERISTICS .......................................................................................................... 4 ABSOLUTE MAXIMUM RATINGS .................................................................................................................... 4 DC ELECTRICAL CHARACTERISTICS........................................................................................ 4 AC ELECTRICAL CHARACTERISTICS........................................................................................ 5 SOLDER REFLOW PROFILE.................................................................................................... 6 INPUT/OUTPUT CIRCUITS .................................................................................................... 7 TYPICAL PERFORMANCE CURVES.......................................................................................... 8 3. DETAILED DESCRIPTION ..................................................................................................................... 9 3.1 SERIAL DIGITAL INPUT ......................................................................................................... 9 3.2 AUTOMATIC CABLE EQUALIZATION ........................................................................................ 9 3.3 CABLE LENGTH INDICATION & CARRIER DETECT/MUTE ........................................................... 9 4. APPLICATION REFERENCE DESIGN .................................................................................................... 10 4.1 PCB LAYOUT .................................................................................................................... 10 4.2 TYPICAL APPLICATION CIRCUIT ........................................................................................... 10 5. REFERENCES.................................................................................................................................. 10 6. PACKAGE & ORDERING INFORMATION............................................................................................... 11 6.1 PACKAGE DIMENSIONS ...................................................................................................... 11 6.2 ORDERING INFORMATION................................................................................................... 11 7. REVISION HISTORY .......................................................................................................................... 12 2 of 12 GENNUM CORPORATION 22212 - 3 GS9064 2.1 2.2 2.3 2.4 2.5 2.6 1. PIN OUT 1.1 PIN ASSIGNMENT 1 16 CD/MUTE VCC 2 15 VCC V 3 14 VEE SDI 4 13 SDO SDI 5 12 SDO VEE 6 11 V AGC+ 7 10 MCLADJ AGC- 8 9 BYPASS EE 1.2 GS9064 16PIN SOIC TOP VIEW GS9064 CLI EE PIN DESCRIPTIONS PIN NUMBER NAME TYPE 1 CLI Output DESCRIPTION CABLE LENGTH INDICATOR An analog voltage proportional to the cable length connected to the serial digital input. NOTE: CLI is recommended for data rates up to 360 Mb/s only. 2, 15 VCC Input Power Most positive power supply connection. Connect to +3.3V. 3, 6, 11, 14 VEE Input Power Most negative power supply connection. Connect to ground. 4, 5 SDI, SDI Input Serial digital differential inputs. 7, 8 AGC+, AGC- Passive Input 9 BYPASS Input 10 MCLADJ Input External AGC capacitor. Should be set to 1F. Forces the CORE stage and the DC RESTORE stage into bypass mode when HIGH. No equalization occurs in this mode. MAXIMUM CABLE LENGTH ADJUST Adjusts the approximate maximum amount of cable to be equalized (from 0m to the maximum cable length). The output is muted (latched to the last state) when the maximum cable length is achieved. NOTE: MCLADJ is recommended for data rates up to 360 Mb/s only. 12, 13 SDO, SDO Output Equalized serial digital differential outputs. 16 CD/MUTE Input / Output MUTE INDICATOR-CONTROL / CARRIER DETECT OUTPUT: the output voltage drops to below 1.2V when the carrier is present and the data outputs are active. INPUT: if the CD/MUTE pin is tied to ground, the data output will never mute and the MCLADJ setting is overwritten. If the CD/MUTE pin is tied to VCC, the data outputs will always mute and the MCLADJ setting is overwritten. 3 of 12 GENNUM CORPORATION 22212 - 3 2. 2.1 ELECTRICAL CHARACTERISTICS ABSOLUTE MAXIMUM RATINGS PARAMETER VALUE Supply Voltage -0.5V to +3.6 VDC 500V Storage Temperature Range -50C< Ts < 125C Input Voltage Range (any input) -0.3 to (VCC + 0.3)V Operating Temperature Range 0C to 70C Power Dissipation 300mW Lead Temperature (soldering, 10 sec.) 260C Moisture Sensitivity Level 2.2 GS9064 Input ESD Voltage 2 DC ELECTRICAL CHARACTERISTICS VCC = 3.3V , VEE = 0V , TA = 0C to 70C, 270Mb/s, unless otherwise shown PARAMETER SYMBOL CONDITIONS MIN TYPICAL MAX UNITS TEST LEVEL NOTES 3.1 3.3 3.5 V 1 - 265 - mW 5 - Supply Voltage VCC Power Consumption PD TA = 25C - S TA = 25C Supply Current Input Common Mode Voltage Output Common Mode Voltage - 80 - mA 1 - VCMIN - 1.75 - V 10 - VCMOUT - VCC - VSDO/2 - mV 7 - Cable length = 0m - 2.5 - V 1 - No signal (max cable length) - 1.9 - V 7 - - 1.3 - V 7 - - 0.69 - V 7 - V CLI DC Voltage Floating MCLADJ DC Voltage MCLADJ Range CD/Mute Output Voltage 0m to max cable length VCD/Mute(OH) Carrier not present VCD/Mute(OL) Carrier present CD/Mute Input Voltage Required to Force Outputs to Mute VCD/Mute) Min to Mute CD/Mute Input Voltage Required to Force Outputs to Activate VCD/Mute Max to Activate 2.6 - - - - 1.2 3.0 - - - - 2.0 1 - 1 - V 7 - V 7 - TEST LEVELS 1. Production test at room temperature and nominal supply voltage with guardbands for supply and temperature ranges. 2. Production test at room temperature and nominal supply voltage with guardbands for supply and temperature ranges using correlated test. 3. Production test at room temperature and nominal supply voltage. 4. QA sample test. 5. Calculated result based on Level 1, 2, or 3. 6. Not tested. Guaranteed by design simulations. 7. Not tested. Based on characterization of nominal parts. 8. Not tested. Based on existing design/characterization data of similar product. 9. Indirect test. 10. Wafer Probe 4 of 12 GENNUM CORPORATION 22212 - 3 2.3 AC ELECTRICAL CHARACTERISTICS VCC = 3.3V , VEE = 0V , TA = 0C to 70C, 270Mb/s, unless otherwise shown PARAMETER SYMBOL CONDITIONS MIN TYPICAL MAX UNITS TEST LEVEL NOTES DRSDI EQ active 143 - 540 Mb/s 6 - Input Swing VSDI Differential, TA =25C 720 800 950 mVp-p 1 - Differential, 50 ohm load, TA =25C - 750 - mVp-p 1 - 270Mb/s, Belden 8281 - 280 - m 7 - - 180 - m 7 - Cable length = 0m Output Swing VSDO Maximum Equalized Cable Length 0.20UI output jitter EQ Pathological 540Mb/s, Belden 8281 0.20UI output jitter EQ Pathological Output Rise/Fall Time tr, tf - 80 220 ps 1 - Mismatch in Rise/Fall Time - - 30 ps 1 - Duty Cycle Distortion - - 100 ps 7 - Overshoot - - 10 % 1 - 15 - - dB 7 - Input Return Loss 20% - 80% IRL TEST LEVELS 1. Production test at room temperature and nominal supply voltage with guardbands for supply and temperature ranges. 2. Production test at room temperature and nominal supply voltage with guardbands for supply and temperature ranges using correlated test. 3. Production test at room temperature and nominal supply voltage. 4. QA sample test. 5. Calculated result based on Level 1, 2, or 3. 6. Not tested. Guaranteed by design simulations. 7. Not tested. Based on characterization of nominal parts. 8. Not tested. Based on existing design/characterization data of similar product. 9. Indirect test. 10. Wafer Probe 5 of 12 GENNUM CORPORATION 22212 - 3 GS9064 Serial Input Data Rate 2.4 SOLDER REFLOW PROFILE Temperature 60-150 sec. 20-40 sec. GS9064 260C 250C 3C/sec max 217C 6C/sec max 200C 150C 25C Time 60-180 sec. max 8 min. max Figure 1 Maximum Pb-free Solder Reflow Profile 60-150 sec. Temperature 10-20 sec. 230C 220C 3C/sec max 183C 6C/sec max 150C 100C 25C Time 120 sec. max 6 min. max Figure 2 Standard Eutectic Solder Reflow Profile 6 of 12 GENNUM CORPORATION 22212 - 3 2.5 INPUT/OUTPUT CIRCUITS All resistors in ohms, all capacitors in farads, unless otherwise shown. 3k 50 50 SDI SDI RC SDO 3.6k 3.6k SDO Figure 3 Input Equivalent Circuit Figure 6 Output Circuit VCC VCC 10k 12k + MCLADJ 10k - 150 CLI + Figure 7 CLI Output Circuit Figure 4 MCLADJ Equivalent Circuit VCC 7.5k OUTPUT STAGE CD/MUTE MUTE CONTROL Internal Reference Bypass Figure 5 CD/MUTE Circuit Figure 8 Bypass Circuit 7 of 12 GENNUM CORPORATION 22212 - 3 GS9064 3k 2.6 TYPICAL PERFORMANCE CURVES All resistors in ohms, all capacitors in farads, unless otherwise shown. 3.5 MCLADJ VOLTAGE (V) 300 250 200 150 100 GS9064 POWER CONSUMPTION (mW) 350 3.0 2.5 50 0 0 20 40 60 2.0 80 0 50 100 TEMPERATURE (C) 150 200 250 300 CABLE LENGTH (m) Figure 9 Power Consumption Figure 12 MCLADJ Input Voltage vs 1694A Cable Length, 270Mb/s 3.5 900 3 700 JITTER (ps) CLI VOLTAGE (V) 1100 2.5 2 500 400 300 200 100 1.5 0 50 100 150 200 250 300 0 0 CABLE LENGTH (m) 100 200 300 400 CABLE LENGTH (m) Figure 10 CLI Voltage vs 8281 Cable Length, 270Mb/s Figure 13 Typical Peak-to-Peak Jitter, PRN223-1, 1694A, 270Mb/s Figure 11 Input 8281, 280m, 270Mb/s Figure 14 Output 8281, 280m, 270Mb/s 8 of 12 GENNUM CORPORATION 22212 - 3 3. DETAILED DESCRIPTION The GS9064 is a high speed bipolar IC designed to equalize SD serial digital signals. The device can typically equalize 350 meters of Belden 1694A cable at 270Mb/s. Powered from a single +3.3V or -3.3V power supply, the device consumes approximately 240mW of power. SERIAL DIGITAL INPUT The SD serial digital input signal may be connected to the input pins (SDI/SDI) in either a differential or single ended configuration. AC coupling of the inputs is recommended, as the SDI and SDI inputs are internally biased at approximately +1.8 volts. 3.2 The GS9064 incorporates an analog cable length indicator (CLI) output and a programmable threshold output mute (MCLADJ). In addition, a multi-function CD/MUTE pin allows control of the GS9064 MUTE functionality for SD inputs. AUTOMATIC CABLE EQUALIZATION The input signal passes through a variable gain equalizing stage whose frequency response closely matches the inverse of the cable loss characteristic. In addition, the variation of the frequency response with control voltage imitates the variation of the inverse cable loss characteristic with cable length. The edge energy of the equalized signal is monitored by a detector circuit which produces an error signal corresponding to the difference between the desired edge energy and the actual edge energy. This error signal is integrated by both an internal and an external AGC filter capacitor providing a steady control voltage for the gain stage. As the frequency response of the gain stage is automatically varied by the application of negative feedback, the edge energy of the equalized signal is kept at a constant level which is representative of the original edge energy at the transmitter. The equalized signal is also DC restored, effectively restoring the logic threshold of the equalized signal to its correct level independent of shifts due to AC coupling. The digital output signals have a nominal voltage of 750mVpp differential, or 375mVpp single ended when terminated with 50 as shown below in Figure 13. 3.3.1 Cable Length Indicator The voltage output of the CLI pin is a representation of the amount of cable present at the inputs of the device. Figure 8 shows the CLI voltage versus cable length (signal strength). At 270Mb/s with no cable length and 800mV input signal levels, the CLI output voltage is approximately 2.5V. As the cable length is increased, the CLI voltage decreases, thereby providing an approximate correlation between the CLI voltage and cable length 3.3.2 Programmable Mute Threshold A voltage programmable mute threshold (MCLADJ) is included to allow muting of the GS9064 output when a selected cable length is reached. This feature allows the device to distinguish between low amplitude SDI signals and noise at its input. Figure 10 shows the relationship between the voltage applied to the MCLADJ pin and the input cable length accepted by the GS9064. For consistent accurate results this may need to be calibrated for each device. The MCLADJ pin may be left unconnected for applications where output muting is not required. This feature has been designed for use in applications such as routers where signal crosstalk and circuit noise cause the equalizer to output erroneous data when no input signal is actually present. The use of a Carrier Detect function with a fixed internal reference does not solve this problem since the signal to noise ratio on the circuit board could be significantly less than the default signal detection level set by the on-chip reference. NOTE: MCLADJ and CLI are only recommended for data rates up to 360 Mb/s. +187.5mV 3.3.3 Carrier Detect/Mute VCM = 2.925V typical SDO -187.5mV SDO +187.5mV 50 50 VCM = 2.925V typical -187.5mV Applying a HIGH INPUT to the CD/Mute pin forces the GS9064 outputs to a muted condition. See the DC Electrical Characteristics table for voltage levels. In this condition the outputs are latched to the last logic level present at the output to avoid signal crosstalk. Applying a LOW INPUT to the CD/Mute pin will force the GS9064 outputs to remain active regardless of input cable length or the voltage applied to the MCLADJ pin. See the DC Electrical Characteristics table for voltage levels. Figure 15 Typical Output Voltage Levels 9 of 12 GENNUM CORPORATION 22212 - 3 GS9064 3.1 3.3 CABLE LENGTH INDICATION & CARRIER DETECT/MUTE When used as an OUTPUT, the CD/Mute pin will provide an indication of the output mute status. The CD/Mute voltage will fall to below 1.2V when the carrier is present and the data outputs are active. NOTE: The CD/Mute pin is not functional in BYPASS mode. 4. APPLICATION REFERENCE DESIGN GS9064 4.1 PCB LAYOUT An FR-4 dielectric can be used, however, controlled impedance transmission lines are required for PCB traces longer than approximately 1cm. Note the following PCB artwork features used to optimize performance: 1. The PCB ground plane is removed under the GS9064 input AND output components to minimize parasitic capacitance. 2. High speed traces are curved to minimize impedance changes. 4.2 TYPICAL APPLICATION CIRCUIT CLI CD/MUTE VCC VCC 10n BNC GS9064 6.4n 1 2 3 1u 4 5 6 7 75 1u 8 75 + 37.4 CLI VCC VEE SDI SDI VEE AGC+ AGC- 10n CD/MUTE VCC VEE SDO SDO VEE MCLADJ BYPASS 16 15 14 13 12 11 10 9 + 4u7 SDO + SDO 4u7 1u MCLADJ NOTE: All resistors in Ohms, capacitors in Farads, and inductors in Henrys, unless otherwise noted. 5. BYPASS REFERENCES Compliant with SMPTE 259M and SMPTE 344. 10 of 12 GENNUM CORPORATION 22212 - 3 6. 6.1 PACKAGE & ORDERING INFORMATION PACKAGE DIMENSIONS * CONTROLLING DIMENSION: MM 16 MILLIMETER 9 H MIN. NOM. MAX. MIN. NOM. MAX. A 1.35 1.63 1.75 0.053 0.064 0.069 A1 0.10 0.15 0.25 0.004 0.006 0.010 A2 1.30 1.40 1.50 0.051 0.055 0.059 b 0.33 0.41 0.51 0.013 0.016 0.020 0.25 0.007 0.010" 8 GAUGE PLANE L b c 0.19 9.80 9.91 10.01 0.386 0.390 0.394 E 3.80 3.90 4.00 0.150 0.154 0.157 e Detail F 1.27 5.80 6.00 6.20 0.228 0.236 0.244 L 0.40 0.64 1.27 0.016 0.025 0.050 0.10 0 8 0.004 0 8 A c A1 A2 0.042 1.07 Y e 0.50 H L1 D 0.010 D L1 Y Seating Plane See Detail F 16 PIN SOIC 6.2 ORDERING INFORMATION PART NUMBER PACKAGE TEMPERATURE RANGE Pb-FREE AND GREEN GS9064-CKD 16 pin SOIC 0C to 70C No GS9064-CKDE3 16 pin SOIC 0C to 70C Yes 11 of 12 GENNUM CORPORATION 22212 - 3 GS9064 E 1 INCH Symbol 7. REVISION HISTORY ECR PCN DATE CHANGES AND/OR MODIFICATIONS A 120607 - July 2002 New Document B 125774 - July 2002 Added detailed block descriptions and initial applications information. C 126688 - September 2002 Change packaging from LGA to SOIC for pin compatibility with the GS1524. 0 127023 - December 2002 Upgrade document to Preliminary Data Sheet and edit AC/DC Characteristics to match current design specification limits. 1 128542 - June 2003 Upgrade document to Data Sheet. Power number corrected. 2 133975 - June 2004 Added lead-free and green information. 3 140763 39738 June 2006 Added solder reflow profile and MSL information. DOCUMENT IDENTIFICATION CAUTION DATA SHEET The product is in production. Gennum reserves the right to make changes at any time to improve reliability, function or design, in order to provide the best product possible. GENNUM CORPORATION Mailing Address: P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3 Shipping Address: 970 Fraser Drive, Burlington, Ontario, Canada L7L 5P5 Tel. +1 (905) 632-2996 Fax. +1 (905) 632-5946 GENNUM JAPAN CORPORATION Shinjuku Green Tower Building 27F, 6-14-1, Nishi Shinjuku, Shinjuku-ku, Tokyo, 160-0023 Japan Tel. +81 (03) 3349-5501, Fax. +81 (03) 3349-5505 GENNUM UK lIMITED 25 Long Garden Walk, Farnham, Surrey, England GU9 7HX Tel. +44 (0)1252 747 000 Fax +44 (0)1252 726 523 ELECTROSTATIC SENSITIVE DEVICES DO NOT OPEN PACKAGES OR HANDLE EXCEPT AT A STATIC-FREE WORKSTATION Gennum Corporation assumes no liability for any errors or omissions in this document, or for the use of the circuits or devices described herein. The sale of the circuit or device described herein does not imply any patent license, and Gennum makes no representation that the circuit or device is free from patent infringement. GENNUM and the G logo are registered trademarks of Gennum Corporation. (c) Copyright 2002 Gennum Corporation. All rights reserved. Printed in Canada. www.gennum.com 12 of 12 22212 - 3 GS9064 VERSION Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Semtech: GS9064-CTDE3 GS9064-CKDE3