TECHNICAL DATA SHEET 1/4 R185A.031.020 STRAIGHT PLUG EZ FIT TYPE Series : ECO 7/16 1/2" CORRUGATED CABLE All dimensions are in mm. . pn . an COMPONENTS BODY CENTER CONTACT OUTER CONTACT INSULATOR GASKET OTHERS PARTS - MATERIALS PLATING (m) BRASS BRONZE BBR SILVER PTFE SILICONE RUBBER BRASS - BBR - Issue : 0943 B In the effort to improve our products, we reserve the right to make changes judged to be necessary. TECHNICAL DATA SHEET 2/4 R185A.031.020 STRAIGHT PLUG EZ FIT TYPE Series : ECO 7/16 1/2" CORRUGATED CABLE PACKAGING SPECIFICATION Standard 1 Unit - Other Contact us CABLE ASSEMBLY ELECTRICAL CHARACTERISTICS Impedance 50 Frequency 0-3 GHz VSWR 1.1 + 0.0000 x F(GHz) Maxi Insertion loss 0.05 F(GHz) dB Maxi RF leakage -( NA - F(GHz)) dB Maxi Voltage rating 1400 Veff Maxi Dielectric withstanding voltage 2500 Veff mini Insulation resistance 10000 M mini MECHANICAL CHARACTERISTICS Center contact retention Axial force - Mating end Axial force - Opposite end Torque 200 N mini 100 N mini NA N.cm mini Stripping a b c d e f mm 5.50 20.0 0.00 0.00 0.00 0.00 Assembly instruction : Recommended cable(s) LCF 1/2" Cu2y LDF4-50A - 1/2" M 1473 Z M 2831 Z Characteristics indicated on this data sheet are those that can be achieved with the highest performance cable. Intrinsic limitations of the cable may diminish the performance of the assembly Cable retention - pull off - torque 400 N mini NA N.cm TOOLING Recommended torque Mating Panel nut Clamp nut A/F clamp nut Mating life Weight 3500 NA 800 19.0000 N.cm N.cm N.cm mm 100 Cycles mini 108.2000 g Part Number . R282.011.050 Hexagon . OTHER CHARACTERISTICS Watertightness:IP67 ENVIRONMENTAL Operating temperature Hermetic seal Panel leakage Description . STRIPPING TOOL -40/+85 C NA Atm.cm3/s NA Issue : 0943 B In the effort to improve our products, we reserve the right to make changes judged to be necessary. TECHNICAL DATA SHEET STRAIGHT PLUG EZ FIT TYPE 1/2" CORRUGATED CABLE Clamp nut Body O-ring1 3/4 R185A.031.020 Series : ECO 7/16 O-ring2 Cable 1) STRIPPING OF THE SHEAT AND THE OUTER CONDUCTOR - Cut the cable end in a hollow with a hacksaw . - Raise the handle and introduce the cable until it stops in the stripping tool. - Push down the handle by exerting a light pressure on it , keep turning the tool until it turns freely. - Hold the handle down , and turn the tool ( of approximately 1/4 of tour ) in the opposite direction , while pulling gently on the cable in order to release pieces of the cable cut. - Raise the handle, slide the cable out and remove loose pieces of cable. - In case of cut parts jammed in the tool : raise the handle , introduce again the stripped cable in the tool, screw slightly the cable into the copper previously cut and remove cable + loose parts. - Push down again the handle. Issue : 0943 B In the effort to improve our products, we reserve the right to make changes judged to be necessary. TECHNICAL DATA SHEET 4/4 R185A.031.020 STRAIGHT PLUG EZ FIT TYPE Series : ECO 7/16 1/2" CORRUGATED CABLE 2) POINTING OF THE CABLE - Introduce the cable in the tool as shown. - Turn the tool to point the inner conductor of the cable. O-ring1 Clamp nut 3) CABLE MOUNTING - Put the O-ring2 in the trough of the cable. - Mount the clamp nut on the cable, until the clipsage of the elastic contact on the first annule. - To push the cable assembly forward to stop on the elastic contact. O-ring2 Outer conductor expand 4) MOUNTING CABLE - Mount the clamp nut with the cable in the body of the connector. Couple of tightening recommended: 800N.cm 21/2Flats Issue : 0943 B In the effort to improve our products, we reserve the right to make changes judged to be necessary. 19/2Flats