SF2038B-3 * * * * * Designed for SDARS IF Receiver Low Insertion Loss 5.0 X 7.0 mm Surface-Mount Case Differential or Single Ended Input and Output Complies with Directive 2002/95/EC (RoHS) 76.500 MHz SAW Filter Pb Absolute Maximum Ratings Rating Maximum Incident Power in Passband Value Units +10 dBm 30 VDC Max. DC voltage between any 2 terminals Storage Temperature Range -40 to +85 Max Soldering Profile C 265C for 10 s SMP-03-S Electrical Characteristics Characteristic Sym Nominal Center Frequency Passband Insertion Loss 1dB Passband 15dB Bandwidth 30dB Bandwidth Amplitude Ripple over fc 6.25 MHz Group Delay Variation over fc 6.25 MHz Rejection 50 to 64.44 MHz 64.44 to 66.70 MHz 86.30 to 87.54 MHz 87.54 to 91.50 MHz 91.50 to 100 MHz Operating Temperature Range Frequency Coeffieient Differential Input Differential Output Case Style Lid Symbolization (YY=year, WW=week, S=shift) See note 4 fC IL BW1 BW15 BW30 Notes Min 1 12.5 1 GDV 1, 3 TA FTC 1 6 40 36 30 31 40 -40 Typ 76.500 10.0 14.0 16.8 18.0 0.70 40 46 41 44 44 47 Max 12.0 18.0 19.2 1.3 150 Units MHz dB MHz MHz MHz dBP-P nsP-P dB +85 C -87 ppm/C 175 ohms 180 ohms SMP-03-S 7 x 5 mm Nominal Footprint RFM SF2038B-3 YYWWS Electrical Connections Connection Terminals Port 1 Hot 10 Port 1 Ground Return or Hot 1 Port 2 Hot 5 Port 2 Ground Return or Hot 6 Case Ground All Others CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. NOTES: 1. 2. 3. 4. 5. 6. 7. 8. 9. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 and measured with 50 network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." The design, manufacturing process, and specifications of this filter are subject to change. Tape and Reel Standard ANSI / EIA 481. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. Murata, stylized Murata logo, and Murata N.A., Inc. are registered trademarks of Murata Manufacturing Co., Ltd. (c)2010-2014 byMurata Murata Electronics N.A., Inc. Copyright (c) Manufacturing Co., Ltd. All Rights Reserved 2007 SF2038B-3 (R) 3/27/14 Page 1 of 3 www.murata.com SMP-03-S Case Pb 12-Terminal Ceramic Surface-Mount Case 5 x 7 mm Nominal Footprint Case Dimensions Dimension A B C D E H J K P Min 6.80 4.80 2.41 0.87 2.87 1.14 mm Nom 7.00 5.00 1.65 0.80 2.54 1.1 2.54 3.00 1.27 Max 7.20 5.20 2.00 Min 0.268 0.189 Inches Nom 0.276 0.197 0.065 Max 0.283 0.205 0.079 2.67 1.13 0.095 0.034 0.100 0.039 0.105 0.044 3.13 1.40 0.113 0.045 0.118 0.050 0.123 0.055 Materials Solder Pad Termination Au plating 30 - 60 inches (76.2-152 m) over 80200 inches (203-508 m) Ni. Lid Fe-Ni-Co Alloy Electroless Nickel Plate (8-11% Phosphorus) 100-200 inches Thick Body Al2O3 Ceramic Pb Free (c)2010-2014 (c) byMurata Murata Electronics N.A., Inc. Copyright Manufacturing Co., Ltd. All Rights Reserved 2007 SF2038B-3 (R) 3/27/14 Page 2 of 3 www.murata.com COMPONENT ORIENTATION and DIMENSIONS 4.0 mm 0.1 1.5 mm +0.1 -0.0 2.0 mm 0.1 1.75 mm 0.1 PIN #1 W (CARRIER TAPE SIZE) 1.5 mm +0.3 -0.0 7.5 mm 0.1 P (PITCH) AO BO USER DIRECTION OF FEED COVER TAPE SIZE 2.15 mm 0.2 KO COVER TAPE 0.32 mm 0.3 Carrier Tape Dimensions Ao 5.5 mm 0.1 Bo 7.5 mm 0.1 Ko 2.0 mm 0.1 Pitch 8.0 mm 0.1 W 16.0 mm 0.3 (c)2010-2014 (c) byMurata Murata Electronics N.A., Inc. Copyright Manufacturing Co., Ltd. All Rights Reserved 2007 SF2038B-3 (R) 3/27/14 Page 3 of 3 www.murata.com