ALUMINUM  ELECTROLYTIC  CAPACITORS
CAT.8100D
UT series
6mmL Chip Type , Wide Temperature Range
Chip type with load life 2000 hours at +105
°C
.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
Specifications
Category
Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan δ)
Stability at Low Temperature
Endurance
Shelf Life
Resistance to soldering
heat
Marking
Performance CharacteristicsItem
–55 to +105°C
4 to 50V
0.1 to 100µF
± 20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater.
Black print on the case top.
Measurement frequency :120Hz at 20°C
The specifications listed at right shall be met
when the capacitors are restored to 20°C after
the rated voltage is applied for 2000 hours at
105°C.
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
U
1
U
2
T
3
1
4
C
5
1
6
0
7
0
8
M
9
C
10
L
11
1
12
G
13
S
14
Configuration
Taping code
Capacitance tolerance (±20%)
Rated voltage (16V)
Rated capacitance (10μF)
Series name
Type
Voltage
Capacitance
105°C Marking
Lot No.
A2P
10
16V
Plastic platform
0.3MAX.
5.8±0.3
φD±0.5
B±0.2
C±0.2
0.5MAX.
A±0.2 A±0.2
E
Positive
Negative
A
B
C
E
4
1.8
4.3
4.3
1.0
5
2.1
5.3
5.3
1.3
6.3
2.4
6.6
6.6
2.2
0.5 to 0.8
(mm)
φD
Voltage mark for 6.3V is 6V .
U
1
U
2
T
3
1
4
C
5
1
6
0
7
0
8
M
9
C
10
L
11
1
12
G
13
S
14
Configuration
Taping code
Capacitance tolerance (±20%)
Rated voltage (16V)
Rated capacitance (10μF)
Series name
Type
Voltage
Capacitance
105°C Marking
Lot No.
A2P
10
16V
Plastic platform
0.3MAX.
5.8±0.3
φD±0.5
B±0.2
C±0.2
0.5MAX.
A±0.2 A±0.2
E
Positive
Negative
A
B
C
E
4
1.8
4.3
4.3
1.0
5
2.1
5.3
5.3
1.3
6.3
2.4
6.6
6.6
2.2
0.5 to 0.8
(mm)
φD
Voltage mark for 6.3V is 6V .
Chip Type Type numbering system (Example : 16V 10
µ
F)
Rated voltage (V)
tan δ (MAX.)
4
0.37
50
0.12
35
0.13
25
0.16
16
0.20
10
0.24
6.3
0.28
Measurement frequency :120Hz
Z–25°C / Z+20°C
Z–40°C / Z+20°C
Rated voltage (V)
Impedance ratio
ZT / Z20 (MAX.)
4
6
12
6.3
3
8
10
3
5
16
2
4
25
2
3
35
2
3
50
2
3
The capacitors are kept on a hot plate for 30 seconds, which is
maintained at 250°C. The capacitors shall meet the characteristic
requirements listed at right when they are removed from the plate
and restored to 20°C.
tan δ
Capacitance
change
200% or less than the initial specified value
Leakage current
Less than or equal to the initial specified value
Within ±25% of the initial capacitance value (16V or less)
Within ±20% of the initial capacitance value (25V or more)
Capacitance change
Leakage current
tan δ
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Frequency coefficient of rated ripple current
Coefficient
Frequency 50 Hz 120 Hz 300 Hz 1 kHz 10 kHz or more
0.70 1.00 1.17 1.36 1.50
Dimensions
Rated ripple current (mArms) at 105°C 120Hz
  0.1
  0.22
  0.33
  0.47
  1
  2.2
  3.3
  4.7
  10
  22
  33
  47
  100
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
4
5
5
6.3
22
30
36
60
0G
4
0J
6.3
1A
10
1C
16
1E
25
1V
35
1H
50
4
5
5
6.3
22
30
36
60
5
5
6.3
6.3
27
35
46
60
4
5
6.3
6.3
18
30
40
50
4
5
6.3
6.3
13
23
38
48
4
5
6.3
15
25
42
4
4
4
4
4
4
4
5
6.3
1.0
2.6
3.2
3.8
6.2
11
14
19
30
Allowable
ripple
Cap.(µF)
V
Code
Rated
ripple
Case size
φD (mm)
UT
UA
Long Life WT
Higher C/V
Long Life
UX
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in page 18, 19.
Please select UX(p.154), UJ(p.160) series if high C/V products are
required.
Please refer to page 3 for the minimum order quantity.