Rev Date: 11/07/2012 1 www.seielect.com
This specification may be changed at any time without prior notice marketing@seielect.com
Please confirm technical specifications before you order and/or use.
RMC
F
/RMCP
Series
General Purpose Thick Film Standard Power
and High Power Chip Resistor
Stackpole Electronics, Inc.
Resistive Product Solutions
Maximum
Current
± 400 ppm/ºC 1 - 9.76 1 - 9.1
± 200 ppm/ºC 10 - 10M 10 - 10M
± 300 ppm/ºC 0.2 - 0.59 0.2 - 0.56
± 200 ppm/ºC 0.604 - 9.76 0.62 - 9.1
± 100 ppm/ºC 10 - 1M 10 - 1M
± 200 ppm/ºC 1.02M - 10M 1.1M - 20M
± 600 ppm/ºC 0.1 - 0.976 0.1 - 0.91
± 200 ppm/ºC 1 - 9.76 1 - 20M
± 100 ppm/ºC 10 - 1M -
± 200 ppm/ºC 1.02M - 10M -
± 200 ppm/ºC 0.1 - 9.76 0.1 - 20M
± 100 ppm/ºC 10 - 1M -
± 200 ppm/ºC 1.02M - 10M -
± 200 ppm/ºC 0.1 - 9.76 0.1 - 20M
± 100 ppm/ºC 10 - 1M -
± 200 ppm/ºC 1.02M - 10M -
± 200 ppm/ºC 0.1 - 0.976 0.1 - 0.91
± 400 ppm/ºC 1 - 9.76 1 - 9.1
± 200 ppm/ºC 10 - 20M
± 100 ppm/ºC 10 - 10M
± 200 ppm/ºC 0.1 - 0.976 0.1 - 0.91
± 400 ppm/ºC 1 - 9.76 1 - 9.1
± 200 ppm/ºC 10 - 10M
± 100 ppm/ºC 10 - 10M
± 200 ppm/ºC 0.1 - 0.976 0.1 - 0.91
± 400 ppm/ºC 1 - 9.76 1 - 9.1
± 200 ppm/ºC 10 - 10M
± 100 ppm/ºC 10 - 10M
± 200 ppm/ºC 1 - 9.76 1 - 9.76
± 100 ppm/ºC 10 - 1M 10 - 1M
± 200 ppm/ºC 1.02M - 10M 1.02M - 10M
± 200 ppm/ºC 1 - 9.76 1 - 9.76
± 100 ppm/ºC 10 - 1M 10 - 1M
± 200 ppm/ºC 1.02M - 10M 1.02M - 10M
± 200 ppm/ºC 1 - 9.76 1 - 9.76
± 100 ppm/ºC 10 - 1M 10 - 1M
± 200 ppm/ºC 1.02M - 10M 1.02M - 10M
± 200 ppm/ºC 1 - 9.76 1 - 9.76
± 100 ppm/ºC 10 - 1M 10 - 1M
± 200 ppm/ºC 1.02M - 10M 1.02M - 10M
± 200 ppm/ºC 1 - 9.76 1 - 9.76
± 100 ppm/ºC 10 - 1M 10 - 1M
± 200 ppm/ºC 1.02M - 10M 1.02M - 10M
± 200 ppm/ºC 1 - 9.76 1 - 9.76
± 100 ppm/ºC 10 - 1M 10 - 1M
± 200 ppm/ºC 1.02M - 10M 1.02M - 10M
± 200 ppm/ºC 1 - 9.76 1 - 9.76
± 100 ppm/ºC 10 - 1M 10 - 1M
± 200 ppm/ºC 1.02M - 10M 1.02M - 10M
(1) Lesser of √PR or maximum working voltage.
(2) Contact factory for extended ohmic values.
(3) Power rating is 0.5W for ohmic values below 1Ω
-
-
-
-
-
-
RMCP2010 1/2 1W
400V 3 AmpRMCP2512 1 2W 200V
2 Amp
RMCP1210 1/4 0.5W 200V 400V 3 Amp
RMCP1206 1/8 0.33W 200V
50V 100V
400V
1 Amp
RMCP0805 1/10 0.25W 150V 300V 2 Amp
50V 100V 1 AmpRMCP0402 1/16S 0.1W
Type / Code Old Type Code
Power Rating
(Watts) @
70ºC
Maximum
Working
Voltage (1) 1% 5%
Ohmic Range (Ω) and Tolerance (2)
1/20 0.05W
Resistance
Temperature
Coefficient
Maximum
Overload
Voltage
RMCF0402
50V
100V
RMCF0201
1 AmpRMCF0603
25V 1 Amp
1/16S 0.063W 50V 1 Amp
1/16 0.1W 100V
RMCF0805 1/10 0.125W 150V 300V
50V
RMCP0603 1/16 0.125W
200V
2 Amp
RMCF1206 1/8 0.25W 200V 400V 2 Amp
400V 3 AmpRMCF1210 1/4 0.33W(3)
RMCF2010 1/2 0.75W
RMCF2512 1 1W 200V
400V 3 Amp200V
400V 3 Amp
400V 3 Amp200V
Features:
•
RMCF – standard power ratings
• RMCP – high power ratings
• Nickel Barrier terminations standard
• Power derating from 100% at 70ºC to zero at +155ºC
• RoHS compliant
Electrical Specifications
Rev Date: 11/07/2012 2 www.seielect.com
This specification may be changed at any time without prior notice marketing@seielect.com
Please confirm technical specifications before you order and/or use.
RMC
F
/RMCP
Series
General Purpose Thick Film Standard Power
and High Power Chip Resistor
Stackpole Electronics, Inc.
Resistive Product Solutions
0.024 ± 0.001 0.012 ± 0.001 0.009 ± 0.0004 0.006 ± 0.002 0.006 ± 0.002 inches
0.60 ± 0.03 0.30 ± 0.03 0.23 ± 0.01 0.15 ± 0.05 0.15 ± 0.05 mm
0.039 ± 0.004 0.020 ± 0.002 0.012 ± 0.004 0.008 ± 0.004 0.010 ± 0.006 inches
1.00 ± 0.10 0.50 ± 0.05 0.30 ± 0.10 0.20 ± 0.10 0.25 ± 0.15 mm
0.061 ± 0.006 0.031 ± 0.006 / -0.004 0.018 ± 0.004 0.012 ± 0.008 0.012 ± 0.008 inches
1.55 ± 0.15 0.80 + 0.15 / -0.10 0.45 ± 0.10 0.30 ± 0.20 0.30 ± 0.20 mm
0.079 ± 0.008 0.049 ± 0.004 0.020 ± 0.006 0.014 ± 0.010 0.014 ± 0.010 inches
2.00 ± 0.20 1.25 ± 0.10 0.50 ± 0.15 0.35 ± 0.25 0.35 ± 0.25 mm
0.126 ± 0.010 0.063 ± 0.006 0.022 ± 0.006 0.020 ± 0.012 0.020 ± 0.012 inches
3.20 ± 0.25 1.60 ± 0.15 0.55 ± 0.15 0.50 ± 0.30 0.50 ± 0.30 mm
0.126 ± 0.010 0.098 ± 0.010 0.022 ± 0.006 0.020 ± 0.012 0.020 ± 0.012 inches
3.20 ± 0.25 2.50 ± 0.25 0.55 ± 0.15 0.50 ± 0.30 0.50 ± 0.30 mm
0.197 ± 0.008 0.098 ± 0.008 0.022 ± 0.006 0.024 ± 0.012 0.024 ± 0.014 inches
5.00 ± 0.20 2.50 ± 0.20 0.55 ± 0.15 0.60 ± 0.30 0.60 ± 0.35 mm
0.248 ± 0.008 0.126 ± 0.010 0.022 ± 0.006 0.024 ± 0.012 0.024 ± 0.014 inches
6.30 ± 0.20 3.20 ± 0.25 0.55 ± 0.15 0.60 ± 0.30 0.60 ± 0.35 mm
L W H a b
Body Length Body Width Body Height Top Termination Bottom Termination
RMCP0805
RMCP1206
RMCP1210
RMCP2512
RMCP2010
RMCP0402
RMCP0603
Type / Code Unit
RMCF0201
Short Time Overload 2.5x rated voltage for 5 seconds ± (2% + 0.1Ω)
Dielectric Withstanding Voltage 100 VAC, 1 minute ± (1% + 0.05Ω)
Resistance to Soldering Heat 260ºC ±5ºC, for 10 sec. ±0.5 sec. (Solder Bath) ± 1%
Solderability 235ºC ±5ºC, for 2 sec. ±0.5 sec. (Colophonium flux) 95% coverage, minimum
-65ºC: 30 min. 25ºC: 2 to 3 min. ±(1% + 0.05Ω)
155ºC: 30 min. 25ºC: 2 to 3 min. Jumper (<0.05Ω)
(5 Cycles)
40ºC ± 2ºC, 90% RH, Rated Load ±(3% + 0.1Ω)
90 min. On, 30 min. Off for 1,000 hrs. -0hrs./+48hrs. Jumper (<0.05Ω)
70ºC ± 2ºC, Rated Load ±(3% + 0.1Ω)
90 min. On, 30 min. Off for 1,000 hrs. -0hrs./+48hrs. Jumper (<0.05Ω)
Voltage Coefficient 1/10 rated voltage for 3 sec. max. then rated voltage for 3 sec. max. ±100 (ppm/V)
Robustness of Termination Bend of 3mm for 5 ± 1 sec. ± (1% + 0.05 Ohm)
Operating Temperature Range: -55ºC to +125ºC (0201 size)
-55ºC to +155ºC (all others)
Endurance (Damp load)
Endurance (Rated load)
Test ResultsTest Test Conditions (JIS C 5202)
Temperature Cycle
Mechanical Specifications
Performance Characteristics
Rev Date: 11/07/2012 3 www.seielect.com
This specification may be changed at any time without prior notice marketing@seielect.com
Please confirm technical specifications before you order and/or use.
RMC
F
/RMCP
Series
General Purpose Thick Film Standard Power
and High Power Chip Resistor
Stackpole Electronics, Inc.
Resistive Product Solutions
1 2 3 4 5 6 7 8 9 10 11 12 13 14
R M C F 0 6 0 3 J T 4 K 7 0
1 2 3 4 5 6 7 8 9 10 11 12 13 14
R M C P 0 6 0 3 J T 4 K 7 0
Size
0201 Code
Value
Code
Quantity
0402 F
E96, E24
10,000
0603 J
E24
5,000
0805
Z
4,000
1206 G
10,000
1210 B
1,000
2010
2512
0201, 0402
0603, 0805, 1206
0603, 0805, 1206
7" Reel - Plastic Tape
Bulk
T7" Reel - Paper Tape
1%
1210, 2010, 2512
0603, 0805, 1206
10" Reel - Paper Tape
Tol
Product Series Packaging Resistance ValuePower Tolerance
4.70 ohm = 4R70
Four characters with the
multiplier used as the
decimal holder.
0.05W
RMCF
5%
Thick Film
Chip Resistors
SizeDescription
0.063W
0.1W
jumper
Zero ohm jumper = 0R00
0.125W
0.25W
0.33W
0.75W 1 Mohm = 1M00
1W
10.0 Kohm = 10K0
0.1 ohm = R100
Size
RMCP High Power 0402 Code Tol Value Code Description Quantity
0603 F 1% E96, E24 10,000
0805 J 5% E24
1206
1210 4,000
2010
2512 10,000
5,000
0603, 0805
1206, 1210
T
7" Reel
Paper Tape
G
0.25W 1 ohm = 1R00
Power Rating
0.1W
0.125W
Tolerance PackagingProduct Series Resistance Value
Size
0402
Four characters with the multiplier
used as the decimal holder.
2W
10 Kohm = 10K0
1 Mohm = 1M00
1W
0.33W
0.5W 2010, 2512
0603, 0805
1206, 1210
10" Reel
Paper Tape
Nominal
Resistance
4.7K
Type Description Code Wattage Size Tolerance Values SEI Types Pkg Qty Description Code
RMC Standard 1/20 0.05W 0201 1% E96,E24 0201, 0402 10,000 7" reel - paper tape R
RMCF RoHS 1/16S 0.063W 0402 5% E24 10,000 10" reel - paper tape G
1/16 0.1W 0603 5,000 7" reel - paper tape R
1/10 0.125W 0805 1,000 bulk A
1/8 0.25W 1206 1210, 2010, 2512 4,000 7" reel - plastic tape R
1/4 0.33W 1210
1/2 0.75W 2010
1 1W 2512
0603, 0805, 1206
RMCF 1/16 5% R
SEI Type Code Tolerance Packaging
Nominal
Resistance
4.7K
Type
Description
Code
Wattage
Size
Tolerance
Values
SEI Types
Pkg Qty
Description
Code
RMCP High Power 0402 0.1W 0402 1% E96,E24 0402 10,000
7" reel - paper tape
R
0603 0.125W 0603
5%
E24
0805 0.25W 0805
1206 0.33W 1206
1210 0.5W 1210
2010 1W 2010 2010, 2512 4,000
2512 2W 2512
0603, 0805,
1206, 1210 5,000 7" reel - paper tape R
0603, 0805,
1206, 1210 10,000 10" reel - paper tape G
RMCP 0603 5% R
SEI Type Code Tolerance Packaging
Legacy Part Number (before January 3, 2011):
How to Order - RMCF
How to Order – RMCP