Rev. 0.1 9/07 Copyright © 2007 by Silicon Laboratories ToolStickUniDC
ToolStickUniDC
TOOLSTICK UNIVERSITY DAUGHTER CARD USER’S GUIDE
1. Handling Recommendations
To enable development, the ToolStick Base Adapter and daughter cards are distributed without any protective
plastics. To prevent damage to the devices and/or the host PC, consider the following recommendations when
using the ToolStick:
Never connect or disconnect a daughter card to or from the ToolStick Base Adapter while the Base Adapter is
connected to a PC.
Always connect and disconnect the ToolStick Base Adapter from the PC by holding the edges of the board.
Figure 1. Proper Method of Holding the ToolStick
Avoid directly touching any of the other components.
Figure 2. Improper Method of Holding the ToolStick
Manipulate mechanical devices on the daughter cards, such as potentiometers, with care to prevent the Base
Adapter or daughter card from accidentally dislodging from their sockets.
ToolStickUniDC
2 Rev. 0.1
2. Contents
The ToolStickUniDC kit contains the following items:
ToolStick University Daughter Card
The ToolStickUniSK Starter Kit includes the following items:
ToolStick Base Adapter
ToolStick University Daughter Card
3-foot USB extension cable
A ToolStick daughter card requires a ToolStick Base Adapter to communicate with the PC. If the daug hter card was
not purchased as part of a Starter Kit, ToolStick Base Adapters can be purchased separately at
www.silabs.com/toolstick.
3. ToolStick Overview
The purpose of the ToolStick is to provide a development and demonstration platform for Silicon Laboratories
microcontrollers and to demonstrate the Silicon Laboratories software tools, including the Integrated Development
Environment (IDE).
The ToolStick development platform consists of two components: the ToolStick Base Adapter and a daughter card.
The ToolStick Base Adapter provides a USB debug interface and data communications path between a Windows
PC and a target microcontroller.
The target microcontroller and application circuitry are located on the daughter card. Some daughter cards, such
as the ToolStick University Daughter Card, are used as general-purpose development platforms for the target
microcontrollers, and some are used to demonstrate a specific feature or application.
The ToolStick University Daughter Card features a Silicon Laboratories C8051F020 Mixed-Signal MCU. The
external circuitry on the daughter card includes a 22.1184 MHz crystal to enable UART communicatio n, 4 LEDs, 4
push-button switches, an 8-bit DIP switch, a potentiometer, and a reset switch. Ports P0, P1, and P2 of the MCU
are accessible via standard headers. A separate header is available for analog input/output that connects external
signals to the ADC and comparator inputs, and DAC outputs of the MCU. A small area for prototyping is also
provided that can be used to connect additional hardware to the microcontroller and use the daughter card as a
developme nt platform.
Figure 3 shows the ToolStick University Daughter Card and identifies the various components.
ToolStickUniDC
Rev. 0.1 3
Figure 3. ToolStick University Daughter Card (Rev 002)
4. Getting Started
The necessary software to download, debug, and communicate with the target microcontroller must be
downloaded from www.silabs.com/mcuniversity. The following software is necessary to build a project, download
code, and comm unicate with the target microco nt ro ller :
Silicon Laboratories Integrated Development Environment (IDE)
Keil Demonstration Toolset
ToolStick Virtual Tools
The Keil Demo Toolset includes a compiler, assembler, and linker. See "5.2.2. Keil Demonstration C51 C
Compiler‚" on page 4 for mor e details about the demo tools. ToolStick Virtual Tools includ e the ToolStick Terminal
application that allows serial communication with the target microcontroller's UART through the ToolStick Base
Adapter. Also included as part of the ToolStick Virtual Tools are the ToolStick Virtual LCD and the ToolStick Virtual
Oscilloscope. The ToolStick Virtual Tools are described in detail in “AN333: ToolStick Virtual Tools User’s Guide”.
Other useful software provided on the Silicon Labs downloads website (www.silabs.com/mcudownloads) includ es:
Configuration Wizard 2
Keil uVision Drivers
All of the above software is described in more detail in “5. Software Overview”.
To simplify the download p rocess, the necessary software described above is provided in two download packages.
The IDE Download package includes the Silicon Labs IDE and the Keil Demo Toolset. The ToolStick Virtual Tools
Download package includes the ToolStick virtual to ols, example code, and documentation including user ’s guides
and data sheets. After downloading (from www.silabs.com/mcuniversity) and installing these two packages, see
the following sections for information regarding the software and running one of the demo applications.
Power LED
C8051F020
AIN0.2
Potentiometer
Reset Switch
22.1184 MH z
Crystal
Analog I/O
Header
P0, P1, P2
Port Headers
P4 DIP
Switches P5 [7:4 ]
LEDs
P5 [3 :0]
Switches
Prototyping
Area
AIN 0 .3 E x tern a l
Input Header
ToolStickUniDC
4 Rev. 0.1
5. Software Overview
5.1. Silicon Laboratories IDE
The Silicon Laboratories IDE integrates a source-code editor, source-level debugger, and an in-system Flash
programmer. See "6. ToolStick University Daughter Card Demo‚" on page 7 for detailed information on how to use
the IDE. The Keil Demonstration Toolset includes a compiler, linker, and assembler and easily integrates into the
IDE. The use of other third-party compilers and assemble rs is also supported.
5.1.1. IDE System Requirements
The Silicon Laboratories IDE requirements:
Pentium-class host PC running Microsoft Windows 2000 or newer.
One available USB port.
64 MB RAM and 40 MB free HD space recommended.
5.1.2. 3rd Party Toolsets
The Silicon Laboratories IDE has native support for many 8051 compilers. The full list of natively-supported tools
is:
Keil
IAR
Raisonance
Tasking
Hi-Tech
SDCC
Please note that the demo applications for the ToolStick University Daughter Card are written for the Keil and
SDCC toolsets.
5.2. Keil Demonstration Toolset
5.2.1. Keil Asse mb le r an d Link er
The assembler and linker that are part of the Keil Demonstration Toolset are the same versions that are found in
the full Keil Toolset. The complete assembler and linker reference manual can be found on-line under the Help
menu in the IDE or in the “SiLabs\MCU\hlp” directory (A51.chm).
5.2.2. Keil Demonstration C51 C Compiler
The demonstration version of the C51 compiler is the same as the full version with these main limitations: (1)
Maximum 2 kB code generation (2) Floating point library not included (3) Programs start at code address 0x0800.
A complete list of limitations can be found on the Keil website, www.keil.com/demo/limits.asp. The C51 compiler
reference manual can be found under the Help menu in the IDE or in the “SiLabs\MCU\hlp” directory (C51.chm).
5.3. Configuration Wizard 2
The Configuration Wizard 2 is a code generation tool for all Silicon Laboratories devices. Code is generated
through the use of dialog boxes for each of the device's peripherals.
ToolStickUniDC
Rev. 0.1 5
Figure 4. Configuration Wizard 2 Utility
The Configuration Wizard 2 utility helps accelerate development by automatically generating initialization source
code to configure and enable the on-chip re sources needed for most design project s. In just a few step s, the wizard
creates complete startup code for a specific Silicon Laboratories MCU. The program is configurable to provide the
output in C or assembly code.
For more information, refer to the Configuration Wizard 2 documentation. The documentation and software are
available from the downloads webpage (www.silabs.com/mcudownloads).
5.4. Keil uVision Silicon Laboratories Drivers
As an alternative to the Silicon Laboratories IDE, the uVision debug driver allows the Keil uVision IDE to
communicate with Silicon Labo ratories on-c hip debug logic. In-system Flash memory programming integrated into
the driver allows for rapid updating of target code. The uVision IDE can be used to start and stop program
execution, set breakpoints, check variables, inspect and modify memory contents, and single-step through
programs running on the actual target hardware.
For more information, please refer to the uVision driver documentation. The documentation and software are
available from the downloads webpage.
ToolStickUniDC
6 Rev. 0.1
5.5. ToolStick Virtual Tools
The ToolStick Virtual Tools include the following applications:
ToolStick Terminal
ToolStick Virtual LCD
ToolStick Virtual Oscilloscope
The ToolStick Terminal program provides the standard terminal interface to the target microcontroller's UART.
However, instead of requiring the usual RS-232 and COM port connection, ToolStick Terminal uses the USB
interface of the ToolStick Base Adapter to provide the same functionality. The ToolStick Terminal integrated into the
ToolStick Virtual Tools uses a baud rate of 230400 bps with a data format of 8-N-1 (8 data bits, No parity bit, 1 stop
bit), and RTS/CTS hardware handshaking enabled.
The ToolStick Virtual LCD application creates a simple LCD panel on the PC that can be controlled by sending
commands and data through the target microcontroller ’s UART interface via the ToolStick Bas e Ada pter.
The ToolStick Virtual Oscilloscope application allows the PC to be used as an oscilloscope by sending data points
to be plotted through the target microcontroller’s UART interface via the ToolStick Base Adapter.
See “AN333: ToolStick Virtual Tools User’s Guide” included in the ToolStick Virtual Tools Download package for
instructions on using the ToolStick Virtual Tools.
ToolStickUniDC
Rev. 0.1 7
6. ToolStick University Daughter Card Demo
The ToolStick Virtual Tools download package includes a simple code example. The example described in this
section is titled UniDC_FeaturesDemo. The purpose of this example is to guide a new user through the features
and capabilities of the IDE and demonstrate the microcontroller’s on-chip debug capabilities. The
UniDC_FeaturesDemo example code simply lights up an LED when a push button is pushed. This demo shows
how to use the IDE to connect and download the firmware, view and modify registers, use watch windows, use
breakpoints, and single-step through code.
6.1. Hardware Setup
Connect the ToolStick hardware to the PC using the steps below while taking note of the recommendations in
Section 1:
1. Connect the ToolStick Base Adapter to the ToolStick University Daughter Card.
2. If available, connect the USB extension cable to the ToolStick Base Adapter.
3. Connect the ToolStick to a USB port on a PC.
Figure 5 shows an example hardware setup.
Figure 5. Hardware Setup Example
ToolStickUniDC
8 Rev. 0.1
6.2. Connecting to the Device and Downloading Firmware
This section describes how to open the IDE, open and build a project, connect to a device, and download the
firmware.
1. Open the Silicon Laboratories IDE from the Start Programs Silicon Laboratories menu.
2. In the IDE, go to Project Open Project.
3. Browse to the de fa ult location C:\SiLabs\MCU\ToolStick\UniversityDC\Firmware\FeaturesDemo\.
4. Select UniDC_FeaturesDemo.wsp and click OK.
5. In the IDE, select Project Rebuild Project.
6. Go to Options Connection Options.
7. Select USB Debug Adapter for the Serial Adapter and JTAG for the Debug Interface, and then click OK as
shown in Figure 6.
Figure 6. Connection Options Screen
8. Go to Debug Connect.
9. Download the code using the Download button on the menu bar, or use Alt-D.
Once these steps are completed, the firmware is built into an object file (Step 5) and downloaded to the device
(Step 9). The device is now ready to begin executing code . If all of these steps were followed successfully, the “Go”
option is enabled in the Debug menu. A green circle icon in the IDE toolbar also indicates that the device is ready
to run. If one of the step s leads to an erro r, make sure that the ToolStick is properly inserted in a USB port and start
again with Step 6.
ToolStickUniDC
Rev. 0.1 9
6.3. Running and Stopping Code Execution
Once the IDE is connected to the device and the firmware is lo aded, the IDE can st art and stop the code execution.
The following steps can be performed using the buttons on the toolbar or using the options in the Debug menu.
1. To start code execution, click the green “Go” button on the toolbar or use the Debug Go menu option. One
green LED (P5.4) on the daughter card will light up. The debug commands in the IDE (single-step, multiple-
step, set breakpoint, and others) are disabled when the device is running.
While the firmware is running,
Press
the push button labeled P5.0 to see another LED (P5.7) light up.
Figure 7. Go Button
2. To stop code execution, click the red “Stop” butt on on th e to olb ar or use t he Debug Stop menu option. The
device will halt code execution, and all of the registers and pins on the device will hold their state.
Figure 8. Stop Button
All debug windows and watch windows are refreshed when the device is stopped. If any of the values in these
windows have changed since the last time the device was halted, the new value is shown in red text instead of
black text.
6.4. Viewing and Modifying Registers
All registers on the device can be viewed and modified when the device is in a halted state. The registers are
grouped to gether accord ing to which periph eral or part of hardware they belong. As an example, this guide shows
how to open the Port s Debug Window and light up an LED directly from the IDE.
1. Open the Ports Debug Window from the View Debug Windows SFR’s Ports menu option shown in
Figure 9. The Ports Debug window appears on the right-hand side of the IDE. In this window, the P74OUT
register is shown. This register sets the output mode of ports 4 through 7.
Figure 9. Ports Debug Window
ToolStickUniDC
10 Rev. 0.1
2. In the debug window, change the value of P74OUT to 0x00. This value turns off all four LEDs on P5[7:4].
Figure 10. Debug Window
3. To write this new value to the device, select Refresh from the Debug Menu or click the Refresh button in the
toolbar.
Figure 11. Refresh Button
4. Click “Go” to resume running the device with the new P74OUT value.
5. Press the push button, P5.0, and notice that it has no effect on the LED P5.7.
6. Re-enable the P5 output mode by writing 0x08 to the P74OUT and clicking the Refresh button.
7. Then, also try changing the upper four bits of the P5 register and click the Refresh button to directly lig ht up the
LEDs.
Changing the values of registers does not require recompiling the code and redownloading the firmware. At any
time, the device can be halted and the values of the registers can be changed. After selecting “Go”, the firmware
will continue execution using the new values. This capability greatly speeds up the debugging process. See the
C8051F020 data sheet for the definitions and usage for all registers.
The debug windows for other sets of registers are found in the View Debug Windows SFR’s menu.
6.5. Enabling and Using Watch Windows
The Debug Windows in the View menu are used to view and modify hardware registers. To view and modify
variables in code, the IDE provides Watch Windows. Just as with register debug windows, variables in the watch
windows are updated each time the device is halted. This section of the User’s Guide explains how to add a
variable to the watch window and modify the variable. In the UniDC_FeaturesDemo example code, the variable
Button_Press_Count is a counter that stores the number of times the P5.0 button was pressed.
1. If the device is running, stop execution using the “Stop” button or use the Debug Stop menu option.
2. In the File Vie w o n the left-hand side of the IDE, double-click on UniDC_FeaturesDemo.c to open the source
file.
ToolStickUniDC
Rev. 0.1 11
3. Scroll to the main function (line 69) and rig ht-click on the varia ble “Button_Press_Count”. In the context menu
that appears, select “Add Button_Press_Count to Watch” and then choose “Default.” On the right-hand
portion of the IDE, the watch window appears and the var iable is added. The current value of the variable is
shown to the right of the name.
Figure 12. Adding Variable to Watch Window
4. Start code execution and press button P5.0 a few times. Stop the device and see that the value of the
Button_Press_Count is incremented.
5. When the device is halted, click on th e value field in the watch window shown in Figure 13, and change the
value to 0. Then, click the Refresh button or select Debug Refresh to write the new value to the device.
Figure 13. Modifying Variable Value in Watch Window
6. Repeat step 4 to watch the variable increment starting at 0.
Changing the values of variables does not require recompiling the code and redownloading the firmware. At any
time, the device can be halted and the variable values changed. The firmware will continue to execute using the
new values.
ToolStickUniDC
12 Rev. 0.1
6.6. Setting and Running to Breakpoints
Silicon Laboratories microcontroller devices support up to four hardware breakpoints. A breakpoint is associated
with a specific line of code. When the processor reaches a hardware breakpoint, code execution stops, and the
IDE refreshes all debug and watch windows. The on-chip debug hardware allows for breakpoints to be placed on
any line of executable code, including code in Interrupt Service Routines. This section provides steps to set a
breakpoint on the line of source code that increments the Button_Press_Count variable.
1. If the device is running, stop execution using the “Stop” button or use the Debug Stop menu option.
2. Scroll to the main function (line 69) and right-click on the Button_Press_Count variable. In the context menu
shown in Figure 14, selec t Insert/Remove Breakpoint. On the left side of the line in the editor window shown
in Figure 15, a red circle is added to indicate that a breakpoint has been placed on the source line.
Figure 14. Inserting Breakpoint
3. Click the Go button or select the Debug Go menu option.
4. Press the button labeled P5.0. The IDE will show that the device is halted. A blue line will be placed in the editor
window to indicate where the code execution has stopped.
Figure 15. Execution Stopped at Breakpoint
5. Start the processor a few more times, and press the button when the processor is executing. Notice that the
IDE halts execution whenever the button is pressed. For every time the processor is started and the button is
pressed, the Button_Press_Count variable also increments by one.
ToolStickUniDC
Rev. 0.1 13
6.7. Single-Stepping Through Firmware
The IDE supports the ability to single-step through firmware one assembly instruction at a time. The IDE reads the
Flash from the device, converts the instructions to assembly and displays them in a disassembly window. The
following steps show how to open the disassembly window and single step through firmware.
1. If there is not a breakpoint already set on the line of code that increments the Button_Press_Count variable,
set the breakpoint using the steps described in Section 6.6.
2. Start the processor using the Go button, and press the button labeled P5.0 on the daughter card to stop
execution on the breakpoint.
3. Select View Debug Windows Disassembly, or click the Disassembly Window button on the toolbar.
The disassembly window shown in Figure 16 will appear on the right-hand side of the IDE (if it is not already
open).
4. To execute one assembly instruction at a time, click the Step button on the toolbar or select the Debug Step
menu option. The highlight ed line in the disasse mbly window indicates the n ext instruction to be execute d. The
blue line marker in the editor window will stay on the same C source line until all of the assembly instructions
are completed.
Figure 16. Disassembly Window
The disassembly window has three columns. The left column is the address of the instruction in Flash. The middle
column is the instruction in hex. The right column is the disassembled instruction. The disassembly debug window
and the capability to single-step through firmware allow a developer to see exactly what instructions are executed
and their output.
ToolStickUniDC
14 Rev. 0.1
7. Additional Demo Examples
In addition to the UniDC_FeaturesDemo example firmware, the ToolStick download package also includes a
demo project called UniDC_VirtualTools_Demo. The instructions for running this demo can be found at the top of
the source file. The ToolStick V irtual Tools are described in “AN333: ToolStick Virtual Tools User’s Guide”.
The project and source files for the demos can be found in the C:\SiLabs\MCU\ToolStick\UniversityDC\Firmware\
default directory.
8. Using the ToolStick University Daughter Card as a Development Platform
The prototyping area on the ToolStick University Daughter Card makes it easy to interface to external hardware.
Ports P0, P1, and P2 are available at the headers. Also available are the analog input/output signals at header J5.
Wires can be soldered between components in the prototyping area and the headers to add interface circuitry.
8.1. C8051F020 Pin Connections
It is important to note that if exte rnal hardwar e is being added, some of the existing components on the board can
interfere with the signaling. The following is a list of port pins on the C8051F020 MCU that are connected to other
components:
P0.0, P0.1—These pins are connected directly to the ToolStick Base Adapter for UART communication. These
two pins are not available on the header labeled PORT 0 (J1).
P3.6, P3.7—These pins are connected directly to the ToolStick Base Adapter’s GPIO pins for use as UART
handshaking signals. The ToolStick Terminal included in the Virtual Tools application configures the GPIO pins
on the Base Adapter as R TS/CTS handshaking pins. This me ans that the pin, P3.7 (CTS), should be configured
as push-pull output, and P3.6 (RTS) should be configured as open-drain input on the ToolStick University
daughter card.
P5[3:0]—These four pins are connected to push-button switches on the daughter card. The series resistors,
R21 through R24, can be removed to disconnect the push-button switch from the pin.
P5[7:4]—These four pins are connected to the cathode terminals of the green LEDs on the daughter card. The
LEDs, D1 through D4, or the series resistors, R1 through R4, can be removed to disconnect the LED from the
pin.
P4—All eight pins of port P4 are connected to the eight-bit DIP switch on the daughter card. The series
resistors, R13 through R20, can be removed to disconnect the DIP switch from the port pin.
AIN0.2—This pin is connected to the outpu t of the potentiometer. The potentiometer can be removed to
disconnect it from the pin.
See the daughte r card schematic in Figure 17 for more information.
9. Board Revision Information
Revision SA-TS003PCB-001 of the ToolStick University Daughter card has the labels fo r the CP0- and CP1- pin s
swapped in the header, J5. This silk-screen error has bee n fixed on revision SA-TS003PCB- 002. Figure 3 on page
3 shows the revised board with the labels in the correct positions. The revision number is located on the back side
of the daughter card.
10. Information Locations
Example source code is installed by default in the “C:\SiLabs\MCU\ToolStick\UniversityDC\Firmware” directory
during the ToolStick installation.
Documentation for the ToolStick kit, including this User’s Guide, can be found in the
C:\SiLabs\MCU\ToolStick\Documentation and the C:\SiLabs\MCU\ToolStick\UniversityDC\Documentation default
directories.
The installer for the ToolStick Virtual Tools software is available at www.silabs.com/mcuniversity.
ToolStickUniDC
Rev. 0.1 15
11. ToolStick University Daughter Card Schematic
Figure 17. Daughter Card Schematic
Disclaimer
Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers
using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific
device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories
reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy
or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply
or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific
written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected
to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no
circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.
Trademark Information
Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS®, EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations
thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISOmodem ®, Precision32®, ProSLIC®, SiPHY®,
USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of
ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders.
http://www.silabs.com
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
USA
Simplicity Studio
One-click access to MCU and
wireless tools, documentation,
software, source code libraries &
more. Available for Windows,
Mac and Linux!
IoT Portfolio
www.silabs.com/IoT SW/HW
www.silabs.com/simplicity Quality
www.silabs.com/quality Support and Community
community.silabs.com
