© Semiconductor Components Industries, LLC, 2010
January, 2010 − Rev. 15
1Publication Order Number:
MC78L00A/D
MC78L00A Series,
NCV78L00A
100 mA Positive Voltage
Regulators
The MC78L00A Series of positive voltage regulators are
inexpensive, easy−to−use devices suitable for a multitude of
applications that require a regulated supply of up to 100 mA. Like
their higher powered MC7800 and MC78M00 Series cousins, these
regulators feature internal current limiting and thermal shutdown
making them remarkably rugged. No external components are
required with the MC78L00 devices in many applications.
These devices offer a substantial performance advantage over the
traditional zener diode−resistor combination, as output impedance
and quiescent current are substantially reduced.
Features
•Wide Range of Available, Fixed Output Voltages
•Low Cost
•Internal Short Circuit Current Limiting
•Internal Thermal Overload Protection
•No External Components Required
•Complementary Negative Regulators Offered (MC79L00A Series)
•Pb−Free Packages are Available
•NCV Prefix for Automotive and Other Applications Requiring Site
and Control Changes
Figure 1. Representative Schematic Diagram
15k
Q1
Q3 Q5
Input
Output
Ground
Q11
Q12
3.0
0-25k
2.85k
5.0k
Q10
3.8k
Q4 Q6
1.2k 1.9k 19k 2.2k
Q9
Q8
C
Q7
1.0k
420
Z1 Q2
Figure 2. Standard Application
A common ground is required between the input and the output voltages. The
input voltage must remain typically 2.0 V above the output voltage even during
the low point on the input ripple voltage.
* Cin is required if regulator is located an appreciable distance from power
supply filter.
** CO is not needed for stability; however, it does improve transient response.
MC78LXXA
Input
Cin*
0.33 mFCO**
0.1 mF
Output
TO−92
P SUFFIX
CASE 029
See detailed ordering and shipping information in the package
dimensions section on page 10 of this data sheet.
ORDERING INFORMATION
Pin: 1. Output
2. Ground
3. Input
PIN CONNECTIONS
18
7
6
5
2
3
4
(Top View)
VOUT
GND
GND
VIN
GND
NC
GND
NC
SOIC−8*
D SUFFIX
CASE 751
*SOIC−8 is an internally modified SO−8 package. Pins
2, 3, 6, and 7 are electrically common to the die attach
flag. This internal lead frame modification decreases
package thermal resistance and increases power
dissipation capability when appropriately mounted on
a printed circuit board. SOIC−8 conforms to all ex-
ternal dimensions of the standard SO−8 package.
See general marking information in the device marking
section on page 16 of this data sheet.
DEVICE MARKING INFORMATION
1
8
http://onsemi.com
123
12
BENT LEAD
TAPE & REEL
AMMO PACK
STRAIGHT LEAD
BULK PACK
3
MC78L00A Series, NCV78L00A
http://onsemi.com
2
ABSOLUTE MAXIMUM RATINGS
Rating Symbol Value Unit
Input Voltage (5.0 V−9.0 V)
Input Voltage (12 V−18 V)
Input Voltage (24 V)
VI30
35
40
Vdc
Storage Temperature Range Tstg −65 to +150 °C
Maximum Junction Temperature TJ150 °C
Moisture Sensitivity Level MSL 1 −
ESD Capability, Human Body Model (Note 1) ESDHBM 2000 V
ESD Capability, Machine Model (Note 1) ESDMM 200 V
ESD Capability, Charged Device Model (Note 1) ESDCDM 2000 V
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. This device series incorporates ESD protection and is tested by the following methods:
ESD Human Body Model tested per AEC−Q100−002 (EIA/JESD22−A114)
ESD Machine Model tested per AEC−Q100−003 (EIA/JESD22−A115)
ESD Charged Device Model tested per EIA/JES D22/C101, Field Induced Charge Model.
THERMAL CHARACTERISTICS
Rating Symbol Value Unit
Package Dissipation PD Internally Limited W
Thermal Characteristics, TO−92
Thermal Resistance, Junction−to−Ambient
RqJA 200 °C/W
Thermal Characteristics, SOIC8
Thermal Resistance, Junction−to−Ambient
RqJA Refer to Figure 8 °C/W
2. Thermal Resistance, Junction−to−Ambient depends on P.C.B. Copper area. See details in Figure 8.
Thermal Resistance, Junction−to−Case is not defined. SOIC 8 lead and TO-92 packages that do not have a heat sink like other packages
may have. This is the reason that a Theta JC is never specified. A little heat transfer will occur through the package but since it is plastic, it is
minimal. The majority of the heat that is transferred is through the leads where they connect to the circuit board.
MC78L00A Series, NCV78L00A
http://onsemi.com
3
ELECTRICAL CHARACTERISTICS (VI = 10 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, −40°C < TJ < +125°C (for MC78LXXAB,
NCV78L05A), 0°C < TJ < +125°C (for MC78LXXAC), unless otherwise noted.)
MC78L05AC, AB, NCV78L05A
Characteristics Symbol Min Typ Max Unit
Output Voltage (TJ = +25°C) VO4.8 5.0 5.2 Vdc
Line Regulation
(TJ = +25°C, IO = 40 mA)
7.0 Vdc ≤ VI ≤ 20 Vdc
8.0 Vdc ≤ VI ≤ 20 Vdc
Regline
−
−
55
45
150
100
mV
Load Regulation
(TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA)
(TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA)
Regload
−
−
11
5.0
60
30
mV
Output Voltage
(7.0 Vdc ≤ VI ≤ 20 Vdc, 1.0 mA ≤ IO ≤ 40 mA)
(VI = 10 V, 1.0 mA ≤ IO ≤ 70 mA)
VO
4.75
4.75
−
−
5.25
5.25
Vdc
Input Bias Current
(TJ = +25°C)
(TJ = +125°C)
IIB
−
−
3.8
−
6.0
5.5
mA
Input Bias Current Change
(8.0 Vdc ≤ VI ≤ 20 Vdc)
(1.0 mA ≤ IO ≤ 40 mA)
DIIB
−
−
−
−
1.5
0.1
mA
Output Noise Voltage
(TA = +25°C, 10 Hz ≤ f ≤ 100 kHz)
Vn−40 −mV
Ripple Rejection (IO = 40 mA,
f = 120 Hz, 8.0 Vdc ≤ VI ≤ 18 V, TJ = +25°C)
RR 41 49 −dB
Dropout Voltage (TJ = +25°C) VI − VO−1.7 −Vdc
NOTE: NCV78L05A: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring
site and change control.
MC78L00A Series, NCV78L00A
http://onsemi.com
4
ELECTRICAL CHARACTERISTICS (VI = 14 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, −40°C < TJ < +125°C (for MC78LXXAB),
0°C < TJ < +125°C (for MC78LXXAC), unless otherwise noted.)
MC78L08AC, AB
Characteristics Symbol Min Typ Max Unit
Output Voltage (TJ = +25°C) VO7.7 8.0 8.3 Vdc
Line Regulation
(TJ = +25°C, IO = 40 mA)
10.5 Vdc ≤ VI ≤ 23 Vdc
11 Vdc ≤ VI ≤ 23 Vdc
Regline
−
−
20
12
175
125
mV
Load Regulation
(TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA)
(TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA)
Regload
−
−
15
8.0
80
40
mV
Output Voltage
(10.5 Vdc ≤ VI ≤ 23 Vdc, 1.0 mA ≤ IO ≤ 40 mA)
(VI = 14 V, 1.0 mA ≤ IO ≤ 70 mA)
VO
7.6
7.6
−
−
8.4
8.4
Vdc
Input Bias Current
(TJ = +25°C)
(TJ = +125°C)
IIB
−
−
3.0
−
6.0
5.5
mA
Input Bias Current Change
(11 Vdc ≤ VI ≤ 23 Vdc)
(1.0 mA ≤ IO ≤ 40 mA)
DIIB
−
−
−
−
1.5
0.1
mA
Output Noise Voltage
(TA = +25°C, 10 Hz ≤ f ≤ 100 kHz)
Vn−60 −mV
Ripple Rejection (IO = 40 mA,
f = 120 Hz, 12 V ≤ VI ≤ 23 V, TJ = +25°C)
RR 37 57 −dB
Dropout Voltage (TJ = +25°C) VI − VO−1.7 −Vdc
ELECTRICAL CHARACTERISTICS (VI = 15 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, −40°C < TJ < +125°C (for MC78LXXAB),
0°C < TJ < +125°C (for MC78LXXAC), unless otherwise noted.)
MC78L09AC, AB
Characteristics Symbol Min Typ Max Unit
Output Voltage (TJ = +25°C) VO8.6 9.0 9.4 Vdc
Line Regulation
(TJ = +25°C, IO = 40 mA)
11.5 Vdc ≤ VI ≤ 24 Vdc
12 Vdc ≤ VI ≤ 24 Vdc
Regline
−
−
20
12
175
125
mV
Load Regulation
(TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA)
(TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA)
Regload
−
−
15
8.0
90
40
mV
Output Voltage
(11.5 Vdc ≤ VI ≤ 24 Vdc, 1.0 mA ≤ IO ≤ 40 mA)
(VI = 15 V, 1.0 mA ≤ IO ≤ 70 mA)
VO
8.5
8.5
−
−
9.5
9.5
Vdc
Input Bias Current
(TJ = +25°C)
(TJ = +125°C)
IIB
−
−
3.0
−
6.0
5.5
mA
Input Bias Current Change
(11 Vdc ≤ VI ≤ 23 Vdc)
(1.0 mA ≤ IO ≤ 40 mA)
DIIB
−
−
−
−
1.5
0.1
mA
Output Noise Voltage
(TA = +25°C, 10 Hz ≤ f ≤ 100 kHz)
Vn−60 −mV
Ripple Rejection (IO = 40 mA,
f = 120 Hz, 13 V ≤ VI ≤ 24 V, TJ = +25°C)
RR 37 57 −dB
Dropout Voltage
(TJ = +25°C)
VI − VO−1.7 −Vdc
MC78L00A Series, NCV78L00A
http://onsemi.com
5
ELECTRICAL CHARACTERISTICS (VI = 19 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, −40°C < TJ < +125°C (for MC78LXXAB),
0°C < TJ < +125°C (for MC78LXXAC), unless otherwise noted.)
MC78L12AC, AB
Characteristics Symbol Min Typ Max Unit
Output Voltage (TJ = +25°C) VO11.5 12 12.5 Vdc
Line Regulation
(TJ = +25°C, IO = 40 mA)
14.5 Vdc ≤ VI ≤ 27 Vdc
16 Vdc ≤ VI ≤ 27 Vdc
Regline
−
−
120
100
250
200
mV
Load Regulation
(TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA)
(TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA)
Regload
−
−
20
10
100
50
mV
Output Voltage
(14.5 Vdc ≤ VI ≤ 27 Vdc, 1.0 mA ≤ IO ≤ 40 mA)
(VI = 19 V, 1.0 mA ≤ IO ≤ 70 mA)
VO
11.4
11.4
−
−
12.6
12.6
Vdc
Input Bias Current
(TJ = +25°C)
(TJ = +125°C)
IIB
−
−
4.2
−
6.5
6.0
mA
Input Bias Current Change
(16 Vdc ≤ VI ≤ 27 Vdc)
(1.0 mA ≤ IO ≤ 40 mA)
DIIB
−
−
−
−
1.5
0.1
mA
Output Noise Voltage
(TA = +25°C, 10 Hz ≤ f ≤ 100 kHz)
Vn−80 −mV
Ripple Rejection (IO = 40 mA,
f = 120 Hz, 15 V ≤VI ≤ 25 V, TJ = +25°C)
RR 37 42 −dB
Dropout Voltage
(TJ = +25°C)
VI − VO−1.7 −Vdc
ELECTRICAL CHARACTERISTICS (VI = 23 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, −40°C < TJ < +125°C (for MC78LXXAB),
S 0°C < TJ < +125°C (for MC78LXXAC), unless otherwise noted.)
MC78L15AC, AB / NCV78L15A
Characteristics Symbol Min Typ Max Unit
Output Voltage (TJ = +25°C) VO14.4 15 15.6 Vdc
Line Regulation
(TJ = +25°C, IO = 40 mA)
17.5 Vdc ≤ VI ≤ 30 Vdc
20 Vdc ≤ VI ≤ 30 Vdc
Regline
−
−
130
110
300
250
mV
Load Regulation
(TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA)
(TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA)
Regload
−
−
25
12
150
75
mV
Output Voltage
(17.5 Vdc ≤ VI ≤ 30 Vdc, 1.0 mA ≤ IO ≤ 40 mA)
(VI = 23 V, 1.0 mA ≤ IO ≤ 70 mA)
VO
14.25
14.25
−
−
15.75
15.75
Vdc
Input Bias Current
(TJ = +25°C)
(TJ = +125°C)
IIB
−
−
4.4
−
6.5
6.0
mA
Input Bias Current Change
(20 Vdc ≤ VI ≤ 30 Vdc)
(1.0 mA ≤ IO ≤ 40 mA)
DIIB
−
−
−
−
1.5
0.1
mA
Output Noise Voltage
(TA = +25°C, 10 Hz ≤ f ≤ 100 kHz)
Vn−90 −mV
Ripple Rejection (IO = 40 mA,
f = 120 Hz, 18.5 V ≤ VI ≤ 28.5 V, TJ = +25°C)
RR 34 39 −dB
Dropout Voltage
(TJ = +25°C)
VI − VO−1.7 −Vdc
MC78L00A Series, NCV78L00A
http://onsemi.com
6
ELECTRICAL CHARACTERISTICS (VI = 27 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, 0 °C < TJ < +125°C, unless otherwise noted.)
MC78L18AC
Characteristics Symbol Min Typ Max Unit
Output Voltage (TJ = +25°C) VO17.3 18 18.7 Vdc
Line Regulation
(TJ = +25°C, IO = 40 mA)
21.4 Vdc ≤ VI ≤ 33 Vdc
20.7 Vdc ≤ VI ≤ 33 Vdc
22 Vdc ≤ VI ≤ 33 Vdc
21 Vdc ≤ VI ≤ 33 Vdc
Regline −
−
45
35
325
275
mV
Load Regulation
(TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA)
(TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA)
Regload
−
−
30
15
170
85
mV
Output Voltage
(21.4 Vdc ≤ VI ≤ 33 Vdc, 1.0 mA ≤ IO ≤ 40 mA)
(20.7 Vdc ≤ VI ≤ 33 Vdc, 1.0 mA ≤ IO ≤ 40 mA)
(VI = 27 V, 1.0 mA ≤ IO ≤ 70 mA)
(VI = 27 V, 1.0 mA ≤ IO ≤ 70 mA)
VO
17.1
17.1
−
−
18.9
18.9
Vdc
Input Bias Current
(TJ = +25°C)
(TJ = +125°C)
IIB
−
−
3.1
−
6.5
6.0
mA
Input Bias Current Change
(22 Vdc ≤ VI ≤ 33 Vdc)
(21 Vdc ≤ VI ≤ 33 Vdc)
(1.0 mA ≤ IO ≤ 40 mA)
DIIB
−
−
−
−
1.5
0.1
mA
Output Noise Voltage
(TA = +25°C, 10 Hz ≤ f ≤ 100 kHz)
Vn−150 −mV
Ripple Rejection (IO = 40 mA,
f = 120 Hz, 23 V ≤ VI ≤ 33 V, TJ = +25°C)
RR 33 48 −dB
Dropout Voltage
(TJ = +25°C)
VI − VO−1.7 −Vdc
MC78L00A Series, NCV78L00A
http://onsemi.com
7
ELECTRICAL CHARACTERISTICS (VI = 33 V, IO = 40 mA, CI = 0.33 mF, CO = 0.1 mF, 0 °C < TJ < +125°C, unless otherwise noted.)
MC78L24AC
Characteristics Symbol Min Typ Max Unit
Output Voltage (TJ = +25°C) VO23 24 25 Vdc
Line Regulation
(TJ = +25°C, IO = 40 mA)
27.5 Vdc ≤ VI ≤ 38 Vdc
28 Vdc ≤ VI ≤ 80 Vdc
27 Vdc ≤ VI ≤ 38 Vdc
Regline
−
−
−
−
50
60
−
300
350
mV
Load Regulation
(TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA)
(TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA)
Regload
−
−
40
20
200
100
mV
Output Voltage
(28 Vdc ≤ VI ≤ 38 Vdc, 1.0 mA ≤ IO ≤ 40 mA)
(27 Vdc ≤ VI ≤ 38 Vdc, 1.0 mA ≤ IO ≤ 40 mA)
(28 Vdc ≤ VI = 33 Vdc, 1.0 mA ≤ IO ≤ 70 mA)
(27 Vdc ≤ VI ≤ 33 Vdc, 1.0 mA ≤ IO ≤ 70 mA)
VO
22.8
22.8
−
−
25.2
25.2
Vdc
Input Bias Current
(TJ = +25°C)
(TJ = +125°C)
IIB
−
−
3.1
−
6.5
6.0
mA
Input Bias Current Change
(28 Vdc ≤ VI ≤ 38 Vdc)
(1.0 mA ≤ IO ≤ 40 mA)
DIIB
−
−
−
−
1.5
0.1
mA
Output Noise Voltage
(TA = +25°C, 10 Hz ≤ f ≤ 100 kHz)
Vn−200 −mV
Ripple Rejection (IO = 40 mA,
f = 120 Hz, 29 V ≤ VI ≤ 35 V, TJ = +25°C)
RR 31 45 −dB
Dropout Voltage
(TJ = +25°C)
VI − VO−1.7 −Vdc
MC78L00A Series, NCV78L00A
http://onsemi.com
8
PD, POWER DISSIPATION (mW)
IIB, INPUT BIAS CURRENT (mA)
IIB, INPUT BIAS CURRENT (mA) VO, OUTPUT VOLTAGE (V)
Figure 3. Dropout Characteristics Figure 4. Dropout Voltage versus
Junction Temperature
Figure 5. Input Bias Current versus
Ambient Temperature
Figure 6. Input Bias Current
versus Input Voltage
Figure 7. Maximum Average Power Dissipation versus
Ambient Temperature − TO−92 Type Package
VI, INPUT VOLTAGE (V)
0 2.0 4.0 6.0 8.0 10
, INPUT/OUTPUT DIFFERENTIAL VOLTAGE (V)
IO
TJ, JUNCTION TEMPERATURE (°C)
0 25 50 75 100 125
-VV
Dropout of Regulation is
defined as when
VO = 2% of VO
TA, AMBIENT TEMPERATURE (°C)
0 25 50 75 100 125
VI, INPUT VOLTAGE (V)
0 5.0 10 15 20 25 30 35 40
TA, AMBIENT TEMPERATURE (°C)
25 50 75 100 125 150
No Heatsink
8.0
6.0
4.0
2.0
0
2.5
2.0
1.5
1.0
0.5
0
4.2
4.0
3.8
3.6
3.4
3.2
3.0
0
5.0
4.0
3.0
2.0
1.0
0
10,000
1000
100
10
MC78L05AC
Vout = 5.0 V
TJ = 25°C
MC78L05AC
Vout = 5.0 V
IO = 40 mA
TJ = 25°C
RqJA = 200°C/W
PD(max) to 25°C = 625 mW
IO = 1.0 mA
IO = 40 mA IO = 100 mA
IO = 70 mA
IO = 1.0 mA
IO = 40 mA
MC78L05AC
VI = 10 V
VO= 5.0 V
IO = 40 mA
30
50
70
90
110
130
150
0.4
0.8
1.2
1.6
2.0
2.4
2.8
02030504010
L, LENGTH OF COPPER (mm)
170 3.2
RqJA
PD
R , THERMAL RESISTANCE
JAθJUNCTION‐TO‐AIR ( C/W)°
, MAXIMUM POWER DISSIPATION (W)
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
2.0 oz.
Copper
Graph represents symmetrical layout
3.0 mmL
L
Figure 8. SOIC−8 Thermal Resistance and Maximum
Power Dissipation versus P.C.B. Copper Length
PD(max) for TA = 50°C
MC78L00A Series, NCV78L00A
http://onsemi.com
9
APPLICATIONS INFORMATION
Design Considerations
The MC78L00A Series of fixed voltage regulators are
designed with Thermal Overload Protection that shuts
down the circuit when subjected to an excessive power
overload condition. Internal Short Circuit Protection limits
the maximum current the circuit will pass.
In many low current applications, compensation
capacitors are not required. However, it is recommended
that the regulator input be bypassed with a capacitor if the
regulator is connected to the power supply filter with long
wire lengths, or if the output load capacitance is large. The
input bypass capacitor should be selected to provide good
high−frequency characteristics to insure stable operation
under all load conditions. A 0.33 mF or larger tantalum,
mylar, or other capacitor having low internal impedance at
high frequencies should be chosen. The bypass capacitor
should be mounted with the shortest possible leads directly
across the regulators input terminals. Good construction
techniques should be used to minimize ground loops and
lead resistance drops since the regulator has no external
sense lead. Bypassing the output is also recommended.
Figure 9. Current Regulator
Figure 10. ± 15 V Tracking Voltage Regulator
The MC78L00 regulators can also be used as a current source
when connected as above. In order to minimize dissipation the
MC78L05C is chosen in this application. Resistor R determines
the current as follows:
For example, a 100 mA current source would require R to be a
50W, 1/2 W resistor and the output voltage compliance would be
the input voltage less 7 V.
IO = 5.0 V + IB
IIB = 3.8 mA over line and load changes
Input
0.33mFR
IO
MC78L05A
Constant
Current to
Grounded Load
-
+
MC1741
+20V
0.33mF
MC78L15A +VO
10k
10k
-VO
7
6
2
3
4
6.5
20V
MPS A70
MPS U55
0.33mF
0.33mF
+VI
-VI
MC78LXXA
MC79LXXA
+VO
-VO
0.33mF
0.1mF
0.1mF
R
Figure 11. Positive and Negative Regulator
MC78L00A Series, NCV78L00A
http://onsemi.com
10
ORDERING INFORMATION
Device Output Voltage
Operating
Temperature Range Package Shipping†
MC78L05ABD
5.0 V TJ = −40° to +125°C
SOIC−898 Units/Rail
MC78L05ABDG SOIC−8 (Pb−Free) 98 Units/Rail
NCV78L05ABDG* SOIC−8 (Pb−Free) 98 Units/Rail
MC78L05ABDR2 SOIC−82500 Tape & Reel
MC78L05ABDR2G SOIC−8 (Pb−Free) 2500 Tape & Reel
NCV78L05ABDR2* SOIC−82500 Tape & Reel
NCV78L05ABDR2G* SOIC−8 (Pb−Free) 2500 Tape & Reel
MC78L05ABP TO−92 2000 Units/Bag
MC78L05ABPG TO−92 (Pb−Free) 2000 Units/Bag
NCV78L05ABPG* TO−92 (Pb−Free) 2000 Units/Bag
MC78L05ABPRA TO−92 2000 Tape & Reel
MC78L05ABPRAG TO−92 (Pb−Free) 2000 Tape & Reel
NCV78L05ABPRAG* TO−92 (Pb−Free) 2000 Tape & Reel
MC78L05ABPRE TO−92 2000 Tape & Reel
MC78L05ABPREG TO−92 (Pb−Free) 2000 Tape & Reel
NCV78L05ABPREG* TO−92 (Pb−Free) 2000 Tape & Reel
MC78L05ABPRM TO−92 2000 Ammo Pack
MC78L05ABPRMG TO−92 (Pb−Free) 2000 Ammo Pack
NCV78L05ABPRMG* TO−92 (Pb−Free) 2000 Ammo Pack
NCV78L05ABPRPG* TO−92 (Pb−Free) 2000 Ammo Pack
MC78L05ACD
5.0 V TJ = 0° to +125°C
SOIC−898 Units/Rail
MC78L05ACDG SOIC−8 (Pb−Free) 98 Units/Rail
MC78L05ACDR2 SOIC−82500 Tape & Reel
MC78L05ACDR2G SOIC−8 (Pb−Free) 2500 Tape & Reel
MC78L05ACP TO−92 2000 Units/Bag
MC78L05ACPG TO−92 (Pb−Free) 2000 Units/Bag
MC78L05ACPRA TO−92 2000 Tape & Reel
MC78L05ACPRAG TO−92 (Pb−Free) 2000 Tape & Reel
MC78L05ACPRE TO−92 2000 Tape & Reel
MC78L05ACPREG TO−92 (Pb−Free) 2000 Tape & Reel
MC78L05ACPRM TO−92 2000 Ammo Pack
MC78L05ACPRMG TO−92 (Pb−Free) 2000 Ammo Pack
MC78L05ACPRP TO−92 2000 Ammo Pack
MC78L05ACPRPG TO−92 (Pb−Free) 2000 Ammo Pack
*NCV78L05A: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control.
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
MC78L00A Series, NCV78L00A
http://onsemi.com
11
ORDERING INFORMATION (continued)
Device Output Voltage
Operating
Temperature Range Package Shipping†
MC78L08ABD
8.0 V
TJ = −40° to +125°C
SOIC−898 Units/Rail
MC78L08ABDG SOIC−8
(Pb−Free)
98 Units/Rail
MC78L08ABDR2 SOIC−82500 Tape & Reel
MC78L08ABDR2G SOIC−8
(Pb−Free)
2500 Tape & Reel
NCV78L08ABDR2* SOIC−82500 Tape & Reel
NCV78L08ABDR2G* SOIC−8
(Pb−Free)
2500 Tape & Reel
MC78L08ABP TO−92 2000 Units/Bag
MC78L08ABPG TO−92
(Pb−Free)
2000 Units/Bag
MC78L08ABPRA TO−92 2000 Tape & Reel
MC78L08ABPRAG TO−92
(Pb−Free)
2000 Tape & Reel
MC78L08ABPRP TO−92 2000 Ammo Pack
MC78L08ABPRPG TO−92
(Pb−Free)
2000 Ammo Pack
MC78L08ACD
TJ = 0° to +125°C
SOIC−898 Units/Rail
MC78L08ACDG SOIC−8
(Pb−Free)
98 Units/Rail
MC78L08ACDR2 SOIC−82500 Tape & Reel
MC78L08ACDR2G SOIC−8
(Pb−Free)
2500 Tape & Reel
MC78L08ACP TO−92 2000 Units/Bag
MC78L08ACPG TO−92
(Pb−Free)
2000 Units/Bag
MC78L08ACPRA TO−92 2000 Tape & Reel
MC78L08ACPRAG TO−92
(Pb−Free)
2000 Tape & Reel
MC78L08ACPRE TO−92 2000 Tape & Reel
MC78L08ACPREG TO−92
(Pb−Free)
2000 Tape & Reel
MC78L08ACPRP TO−92 2000 Ammo Pack
MC78L08ACPRPG TO−92
(Pb−Free)
2000 Ammo Pack
MC78L00A Series, NCV78L00A
http://onsemi.com
12
ORDERING INFORMATION (continued)(continued)
Device Shipping†
Package
Operating
Temperature Range
Output Voltage
MC78L09ABD
9.0 V TJ = −40° to +125°C
SOIC−898 Units/Rail
MC78L09ABDG SOIC−8
(Pb−Free)
98 Units/Rail
MC78L09ABDR2 SOIC−82500 Tape & Reel
MC78L09ABDR2G SOIC−8
(Pb−Free)
2500 Tape & Reel
MC78L09ABPRA TO−92 2000 Tape & Reel
MC78L09ABPRAG TO−92
(Pb−Free)
2000 Tape & Reel
MC78L09ABPRP TO−92 2000 Ammo Pack
MC78L09ABPRPG TO−92
(Pb−Free)
2000 Ammo Pack
MC78L09ACD
9.0 V TJ = 0° to +125°C
SOIC−898 Units/Rail
MC78L09ACDG SOIC−8
(Pb−Free)
98 Units/Rail
MC78L09ACDR2 SOIC−82500 Tape & Reel
MC78L09ACDR2G SOIC−8
(Pb−Free)
2500 Tape & Reel
MC78L09ACP TO−92 2000 Units/Bag
MC78L09ACPG TO−92
(Pb−Free)
2000 Units/Bag
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
MC78L00A Series, NCV78L00A
http://onsemi.com
13
ORDERING INFORMATION (continued)
Device Output Voltage
Operating
Temperature Range Package Shipping†
MC78L12ABD
12 V
TJ = −40° to +125°C
SOIC−898 Units/Rail
MC78L12ABDG SOIC−8
(Pb−Free)
98 Units/Rail
MC78L12ABDR2 SOIC−82500 Tape & Reel
MC78L12ABDR2G SOIC−8
(Pb−Free)
2500 Tape & Reel
NCV78L12ABDG* SOIC−8
(Pb−Free)
98 Units/Rail
NCV78L12ABDR2* SOIC−82500 Tape & Reel
NCV78L12ABDR2G* SOIC−8
(Pb−Free)
2500 Tape & Reel
MC78L12ABP TO−92 2000 Units/Bag
MC78L12ABPG TO−92
(Pb−Free)
2000 Units/Bag
MC78L12ABPRP TO−92 2000 Ammo Pack
MC78L12ABPRPG TO−92
(Pb−Free)
2000 Ammo Pack
NCV78L12ABPG* TO−92
(Pb−Free)
2000 Units/Bag
MC78L12ACD
TJ = 0° to +125°C
SOIC−898 Units/Rail
MC78L12ACDG SOIC−8
(Pb−Free)
98 Units/Rail
MC78L12ACDR2 SOIC−82500 Tape & Reel
MC78L12ACDR2G SOIC−8
(Pb−Free)
2500 Tape & Reel
MC78L12ACP TO−92 2000 Units/Bag
MC78L12ACPG TO−92
(Pb−Free)
2000 Units/Bag
MC78L12ACPRA TO−92 2000 Tape & Reel
MC78L12ACPRAG TO−92
(Pb−Free)
2000 Tape & Reel
MC78L12ACPRE TO−92 2000 Tape & Reel
MC78L12ACPREG TO−92
(Pb−Free)
2000 Tape & Reel
MC78L12ACPRM TO−92 2000 Ammo Pack
MC78L12ACPRMG TO−92
(Pb−Free)
2000 Ammo Pack
MC78L12ACPRP TO−92 2000 Ammo Pack
MC78L12ACPRPG TO−92
(Pb−Free)
2000 Ammo Pack
*NCV78L12A: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control.
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
MC78L00A Series, NCV78L00A
http://onsemi.com
14
ORDERING INFORMATION (continued)
Device Output Voltage
Operating
Temperature Range Package Shipping†
MC78L15ABD
15 V
TJ = −40° to +125°C
SOIC−898 Units/Rail
MC78L15ABDG SOIC−8
(Pb−Free)
98 Units/Rail
MC78L15ABDR2 SOIC−82500 Tape & Reel
MC78L15ABDR2G SOIC−8
(Pb−Free)
2500 Tape & Reel
NCV78L15ABDR2G* SOIC−8
(Pb−Free)
2500 Tape & Reel
MC78L15ABP TO−92 2000 Units/Bag
MC78L15ABPG TO−92
(Pb−Free)
2000 Units/Bag
MC78L15ABPRA TO−92 2000 Tape & Reel
MC78L15ABPRAG TO−92
(Pb−Free)
2000 Tape & Reel
MC78L15ABPRP TO−92 2000 Ammo Pack
MC78L15ABPRPG TO−92
(Pb−Free)
2000 Ammo Pack
MC78L15ACD
TJ = 0° to +125°C
SOIC−898 Units/Rail
MC78L15ACDG SOIC−8
(Pb−Free)
98 Units/Rail
MC78L15ACDR2 SOIC−82500 Tape & Reel
MC78L15ACDR2G SOIC−8
(Pb−Free)
2500 Tape & Reel
MC78L15ACP TO−92 2000 Units/Bag
MC78L15ACPG TO−92
(Pb−Free)
2000 Units/Bag
MC78L15ACPRA TO−92 2000 Tape & Reel
MC78L15ACPRAG TO−92
(Pb−Free)
2000 Tape & Reel
MC78L15ACPRP TO−92 2000 Ammo Pack
MC78L15ACPRPG TO−92
(Pb−Free)
2000 Ammo Pack
*NCV78L15A: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control.
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
MC78L00A Series, NCV78L00A
http://onsemi.com
15
ORDERING INFORMATION (continued)
Device Output Voltage
Operating
Temperature Range Package Shipping†
MC78L18ABP
18 V
TJ = −40° to +125°C
TO−92 2000 Units/Bag
MC78L18ABPG TO−92
(Pb−Free)
2000 Units/Bag
MC78L18ACP
TJ = 0° to +125°C
TO−92 2000 Units/Bag
MC78L18ACPG TO−92
(Pb−Free)
2000 Units/Bag
MC78L18ACPRA TO−92 2000 Tape & Reel
MC78L18ACPRAG TO−92
(Pb−Free)
2000 Tape & Reel
MC78L18ACPRM TO−92 2000 Ammo Pack
MC78L18ACPRMG TO−92
(Pb−Free)
2000 Ammo Pack
MC78L18ACPRP TO−92 2000 Ammo Pack
MC78L18ACPRPG TO−92
(Pb−Free)
2000 Ammo Pack
MC78L24ABP
24 V
TJ = −40° to +125°C
TO−92 2000 Units/Bag
MC78L24ABPG TO−92
(Pb−Free)
2000 Units/Bag
NCV78L24ABPRPG* TO−92
(Pb−Free)
2000 Units/Bag
MC78L24ACP
TJ = 0° to +125°C
TO−92 2000 Units/Bag
MC78L24ACPG TO−92
(Pb−Free)
2000 Units/Bag
MC78L24ACPRA TO−92 2000 Tape & Reel
MC78L24ACPRAG TO−92
(Pb−Free)
2000 Tape & Reel
MC78L24ACPRP TO−92 2000 Ammo Pack
MC78L24ACPRPG TO−92
(Pb−Free)
2000 Ammo Pack
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
MC78L00A Series, NCV78L00A
http://onsemi.com
16
ALYWB
G
8LxxA
SOIC−8
D SUFFIX
CASE 751
xx = 05, 08, 09, 12, or 15
A = Assembly Location
L = Wafer Lot
Y = Year
W = Work Week
B, C = Temperature Range
G= Pb−Free Package
MARKING DIAGRAMS
MC78L
zzABP
ALYWWG
G
zz = 05, 08, 09, 12, 15, 18 or 24
A = Assembly Location
L = Wafer Lot
Y = Year
WW = Work Week
G= Pb−Free Package
(Note: Microdot may be in either location)
TO−92
P SUFFIX
CASE 029
ALYWC
G
8LxxA
MC78L
zzACP
ALYWWG
G
123
1
8
1
8
123
MC78L00A Series, NCV78L00A
http://onsemi.com
17
PACKAGE DIMENSIONS
SOIC−8 NB
D SUFFIX
CASE 751−07
ISSUE AJ
SEATING
PLANE
1
4
58
N
J
X 45_
K
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
A
BS
D
H
C
0.10 (0.004)
DIM
A
MIN MAX MIN MAX
INCHES
4.80 5.00 0.189 0.197
MILLIMETERS
B3.80 4.00 0.150 0.157
C1.35 1.75 0.053 0.069
D0.33 0.51 0.013 0.020
G1.27 BSC 0.050 BSC
H0.10 0.25 0.004 0.010
J0.19 0.25 0.007 0.010
K0.40 1.27 0.016 0.050
M0 8 0 8
N0.25 0.50 0.010 0.020
S5.80 6.20 0.228 0.244
−X−
−Y−
G
M
Y
M
0.25 (0.010)
−Z−
Y
M
0.25 (0.010) ZSXS
M
____
1.52
0.060
7.0
0.275
0.6
0.024
1.270
0.050
4.0
0.155
ǒmm
inchesǓ
SCALE 6:1
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
SOLDERING FOOTPRINT*
MC78L00A Series, NCV78L00A
http://onsemi.com
18
PACKAGE DIMENSIONS
TO−92 (TO−226)
P SUFFIX
CASE 29−11
ISSUE AM
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. CONTOUR OF PACKAGE BEYOND DIMENSION R
IS UNCONTROLLED.
4. LEAD DIMENSION IS UNCONTROLLED IN P AND
BEYOND DIMENSION K MINIMUM.
R
A
P
J
L
B
K
G
H
SECTION X−X
C
V
D
N
N
XX
SEATING
PLANE DIM MIN MAX MIN MAX
MILLIMETERSINCHES
A0.175 0.205 4.45 5.20
B0.170 0.210 4.32 5.33
C0.125 0.165 3.18 4.19
D0.016 0.021 0.407 0.533
G0.045 0.055 1.15 1.39
H0.095 0.105 2.42 2.66
J0.015 0.020 0.39 0.50
K0.500 --- 12.70 ---
L0.250 --- 6.35 ---
N0.080 0.105 2.04 2.66
P--- 0.100 --- 2.54
R0.115 --- 2.93 ---
V0.135 --- 3.43 ---
1
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION:
MILLIMETERS.
3. CONTOUR OF PACKAGE BEYOND
DIMENSION R IS UNCONTROLLED.
4. LEAD DIMENSION IS UNCONTROLLED IN
P AND BEYOND DIMENSION K MINIMUM.
RA
P
J
B
K
G
SECTION X−X
C
V
D
N
XX
SEATING
PLANE DIM MIN MAX
MILLIMETERS
A4.45 5.20
B4.32 5.33
C3.18 4.19
D0.40 0.54
G2.40 2.80
J0.39 0.50
K12.70 ---
N2.04 2.66
P1.50 4.00
R2.93 ---
V3.43 ---
1
T
STRAIGHT LEAD
BULK PACK
BENT LEAD
TAPE & REEL
AMMO PACK
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any
liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental
damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over
time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under
its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body,
or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death
may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees,
subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of
personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part.
SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
MC78L00A/D
PUBLICATION ORDERING INFORMATION
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your loca
Sales Representative