I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER 28-DIP-600A The S1D2500A01 is a very high frequency video amplifier system with I2C Bus control used in Monitors with high resolution up to1280 x 1024. It contains 3 matched R/G/B video Amplifiers with OSD interface and provides flexible interfacing to I2C Bus controlled adjustment systems. FUNCTIONS * R/G/B Video Amplifier * OSD Interface * I2C BUS Control * Contrast/OSD Contrast ORDERING INFORMATION * Brightness Control * Cut-Off Brightness Control * R/G/B SUB Contrast/Cut-Off Control * Blank/Clamp Gate Device Package Operating Temperature S1D2500A01-D0B0 28-DIP-600A -20 C -- +75C * Half tone * Brightness Uniformity FEATURES * 3 - Channel R/G/B Video Amplifier, 150MHz @f-3dB * I2C Bus Control Items - Contrast Control - SUB Contrast Control For Each Channel - Brightness Control - OSD Contrast Control * Clamp Gate With Anti OSD Sagging * B/U (Brightness Uniformity) Interface * Video Input Clamp, BRT Clamp * Video & OSD Half Tone Function on OSD Picture (OSD Raster Selection by HS1, 2: 4 colors) - Cut-off Brightness Control * OSD Interface, OSD BLK - Cut-off Control For Each Channel * ABL - Switch Registers for SBLK and Video Half Tone and * TTL R/G/B OSD Inputs, 80MHz bandwidth Cut-Off INT/EXT * SUB Contrast Control Range: -11dB * Contrast Control Range: -38dB * OSD Contrast Control Range: -38dB * Capable of 7.0Vpp Output Swing Range * Video/OSD High Speed Switch 1 I 2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 BLOCK DIAGRAM ONE (RED) OF THREE CHANNELS ROSD GOSD 1 OSD INTERFACE BLK VIDEO OSD SWITCH 2 OSD RASTER OSD CONTRAST VIDEO HALF-TONE 26 ROUT A2 + SUB CONTRAST VIDEO CONTRAST CLP A1 A3 BOSD 3 VCC2 9 + + gm1 RIN 5 VCC1 6 gm2 HALF-TONE CLP Cut Off 27 RCLP 17 RCT 23 VCC3 22 GND3 21 BOUT 20 BCLP 15 BCT + BLK CLP OSD RASTER SELECT OSD RASTER COLOR D6:7(0AH) SOFT BLANK D0(0AH) CLP 18 BIN 10 BLK 19 CLAMP GATE BLANK GATE I2 C BUS CONTROL CUT OFF BRIGHT (06H) VIDEO/OSD SWITCH VIDEO HALF-TONE CUT OFF INT/EXT SWITCH(0AH) 4 B/U INTERFACE CUT OFF EXT OFFSET D3:5 (0AH) VI/OSD_SW 28 R/G/B CUT OFF CONTROL (07/08/09H) B/U VIDEO-HALF TONE SWITCH D1(0AH) BRIGHTNESS CONTROL (01H) 8 OSD CONT CONTROL (05H) GIN R/G/B DRIVE CONTROL (02/03/04H) 7 CONTRAST CONTRAL (00H) GND1 24 GOUT 25 GCLP 16 GCT 12 ABL 14 SDA 13 SCL INTERFACE & CONTROL GND(L) 2 11 I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 PIN CONFIGURATION 1 ROSD B/U 28 2 GOSD RCLP 27 3 BOSD ROUT 26 VI/OSD_SW GCLP 25 5 RIN GOUT 24 6 VCC1 VCC3 23 7 GND1 GND3 22 8 GIN BOUT 21 9 VCC2 BCLP 20 10 BIN BLK 19 11 GND(L) CLP 18 12 ABL RCT 17 13 SCL GCT 16 14 SDA BCT 15 S1D2500A 4 Table 1. Pin Configuration Pin No Symbol I/O Configuration 1 ROSD I Red OSD Input 2 GOSD I Green OSD Input 3 BOSD I Blue OSD Input 4 VI/OSD_SW I Video or OSD Switch 5 RIN I Red Video Input 6 VCC1 - VCC (normal) 7 GND1 - Ground1 (normal) 8 GIN I Green Video Input 9 VCC2 - VCC (normal) 3 I 2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 Table 1. Pin Configuration 4 Pin No Symbol I/O Configuration 10 BIN I Blue Video Input 11 GND (L) - Ground2 (logic) 12 ABL - Automatic Beam Limit 13 SCL I/O Serial Clock 14 SDA I/O Serial Data 15 BCT I Blue Cut Off Control 16 GCT I Green Cut Off Control 17 RCT I Red Cut Off Control 18 CLP I Clamp Gate Signal Input 19 BLK I Blank Gate Signal Input 20 BCLP - Blue Clamp Cap 21 BOUT O Blue Video Output 22 GND3 - Ground3 (drive part) 23 VCC3 - VCC (drive part) 24 GOUT O Green Video Output 25 GCLP - Green Clamp Cap 26 ROUT O Red Video Output 27 RCLP - Red Clamp Cap 28 B/U I Brightness Uniformity I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 PIN DESCRIPTION Table 2. Pin Description Pin No Pin Name 1 Red OSD Input (ROSD) Green OSD Input (GOSD) Blue OSD Input (BOSD) 2 3 Schematic Description OSD input signals are in TTL level and will be connected to ground when switching to video input VCC 1.29/ 1.02V 1.16/ 0.90V PIN 1 4 Video/OSD Switch (VI/OSD_SW) 6V VCC Video/OSD switch signal is TTL level PIN4 = "high", OSD input PIN4 = "Low", video input PIN 4 5 8 10 6 Red Video Input (RIN) Green Video Input (GIN) Blue Video Input (BIN) VCC PIN 5 VCC1 - 9 MAX input video signal is 0.7 Vpp Supply voltage (except drive part) VCC2 5 I 2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 Table 2. Pin Description (Continued) Pin No Pin Name 7 GND1 Schematic Description Ground (analogue) 11 GND2 (GND (L) ) 15 Blue Cut-Off (BCT) Green Cut-Off (GCT) Red Cut-Off (RCT) 16 17 Ground (logic) Cut-Off Control Output PIN 17 0~180uA 0~540uA Cut-Off BRT 18 Cut-Off 80uA 160uA 320uA Cut-Off Offset Clamp Gate Input (CLP) 5.1V VCC Video amp active when clamp gate signal is in low TTL level. Clamp gate Min. pulse width : 0.2us, at fh: 50KHz PIN 18 19 7V Blank Gate Input (BLK) PIN 19 6 VCC Video amp blanks video signal when blank gate signal is in low TTL level. I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 Table 2. Pin Description (Continued) Pin No Pin Name 26 Red Video Output (ROUT) Green Video Output (GOUT) Blue Video Output (BOUT) 24 21 Schematic Description Video signal output VCC PIN 26 20 25 27 Blue Clamp Cap (BCLP) Green Clamp Cap (GCLP) Red Clamp Cap (RCLP) Brightness control activated by charging and discharging of the external cap. (0.1F) (During low clamp gate) PIN 27 22 GND3 - Ground (drive part) 23 VCC3 - Supply voltage (drive part) 13 14 SCL SDA 54uA 27uA 3.22V Serial clock input port of I2C BUS Serial data input port of I2C BUS PIN 13 7 I 2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 Table 2. Pin Description (Continued) Pin No Pin Name 28 B/U Input (B/U) Schematic Description Parabola input via AC coupling cap VCC 4.6V PIN 28 100uA 12 VCC ABL Input (ABL) PIN 12 8 Automatic beam limitation input (Control Range: 0.5 -- 4.5V) I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 ABSOLUTE MAXIMUM RATING (TA = 25 C) (1) Table 3. Absolute Maximum Rating Value No Item Symbol Unit Min Typ Max 1 Maximum Supply Voltage VCC1/2/3/VDD - - 13.2 V 2 Operating Temperature (2) Topr -20 - 75 C 3 Storage Temperature Tstg -65 - 150 C 4 Operating Supply Voltage Vccop 11.4 12.0 12.6 V (3) 5 Power Dissipation PD - - 2.0 W THERMAL & ESD PARAMETER Table 4. Thermal & ESD Parameter Value No Item Symbol Unit Min Typ Max 1 Thermal Resistance (Junction-ambient) ja - 46 - C/W 2 Junction Temperature Tj - 150 - C 3 Human Body Mode (C = 100p, R = 1.5k) HBM 2 - - KV 4 Machine Model (C = 200p, R = 0) MM 300 - - V 5 Charge Device Model CDM 800 - - V ELECTRICAL CHARACTERISTICS DC Electrical Characteristics Ta = 25 C, VCC1 = VCC2 = VCC3 = 12V; V4 = 0V; unless otherwise stated Table 5. DC Electrical Characteristics Parameter Symbol Min Typ Max Unit Supply Current ICC(4) 85 110 135 mA Clamp Gate Low Input Voltage V151 0.8 1.5 3.0 V Clamp Gate High Input Voltage V15h 0.8 1.5 2.0 V 9 I 2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 Table 5. DC Electrical Characteristics (Continued) Parameter Symbol Min Typ Max Unit Clamp Gate Low Input Current I15l -5.0 -2.0 - A Clamp Gate High Input Current I15h - 0.01 1.0 A Blank Gate Low Input Voltage V16l 0.8 1.5 3.0 V Blank Gate High Input Voltage V16h 0.8 1.5 2.0 V Blank Gate Low Input Current I16l -5.0 -2.0 - A Blank Gate High Input Current I16h - 0.01 1.0 A Vbias 1.6 1.9 2.2 V Output Clamp Cap Charge Current Iclamp+ 0.45 0.75 1.10 mA Output Clamp Cap Discharge Current Iclamp- -1.10 -0.75 -0.45 mA Video Output Low Voltage VOL - 100 200 mV Video Output High Voltage VOH 6.2 7.5 9.0 V Video Black Level Output Voltage (POR) VOBL 1.9 2.2 2.5 V VO BL(5) -0.3 - 0.3 V VOB - 0.1 0.2 V losd, ldirve lcon - 0.25 1 uA Vspot 9.2 10.4 11.2 V Video Input bias Voltage Video Black Level Output Voltage Video Output Blanked Voltage Contrast/Drive Control Input Current Spot Killer Voltage 10 I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 AC Electrical Characteristics Ta = 25 C, VCC1 = VCC2 = VCC3 = 12V; V4 = 0V. Vin = 0.56Vpp Manually adjust Video Output pins 21, 24 and 26 to 4V DC for the AC test (11) unless otherwise stated(12) Table 6. AC Electrical Characteristics Parameter Symbol Min Typ Max Unit AV max 15.5 17.5 19.5 dB Contrast Attenuation 1 Avc1 -4.5 -6.0 -7.5 dB Contrast Attenuation 2 Avc2 - -38 -35 dB Drive Attenuation1 Avd1 -3 -4 -5 dB Drive Attenuation 2 Avd2 -11 -8 -5 dB Absolute Gain Match AV match(6) -1 - 1 dB Gain Change between Amplifiers A V track(7) -1 - 1 dB Video Amplifier Distortion THD - 1 5 % Video Amp Bandwidth (7,8) f (-3dB) 130 150 - MHz Video Output Rise Time (7) tr (Video) - 2.3 2.8 ns Video Output Fall Time (7) tf (Video) - 3.2 4.0 ns Video Amplifier 10kHz Isolation Viso_10K(9) - -65 -45 dB Video Amplifier 10MHz Isolation Viso_10M(7,9) - -50 -35 dB Blank Output Rise Time (7) tr (Blank) - 6 15 ns Blank Output Fall Time (7) tf (Blank) - 10 30 ns End of Blanking Propagation Delay tr-prop (Blank) - 23 50 ns Start of Blanking Propagation Delay tf-prop (Blank) - 20 45 ns Symbol Min Typ Max Unit VOSDI 0.4 1.3 3.0 V Video Amplifier Gain OSD Electrical Characteristics Ta = 25 C, V CC1 = VCC2 = VCC3 = 12V; V19 = 4V; V12 = V28 = 0V; V1 = V2 = V3 = 4V; V4 = 4V; unless otherwise stated Table 7. OSD Electrical Characteristics Parameter OSD Input Low Input Voltage 11 I 2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 Table 7. OSD Electrical Characteristics (Continued) Parameter Symbol Min Typ Max Unit OSD Input High Input Voltage VOSDh 0.4 0.8 1.2 V OSD Select Low Input Voltage V4I 0.8 1.6 3.0 V OSD Select High Input Voltage V4h 0.8 1.6 2.0 V OSD Select Low Input Current I4I -10 -5 - A OSD Select High Input Current I4h 70 100 130 A VBLV-OSD - 0.1 0.2 V VOSD 2.6 3.6 4.6 VPP VOSD_ATT 30 50 70 % VOSD -7 - 7 % Video to OSD Switch Time (7) tr (OSD S) - 4 10 ns OSD to Video Switch Time (7) tf (OSD S) - 11 20 ns Video to OSD Propagation Delay tr-pr (OSD S) - 11 25 ns OSD to Video Propagation Delay tf-pr (OSD S) - 12 25 ns OSD Rising Time tr (OSD) - 4 8 ns OSD Falling Time tf (OSD) - 5 10 ns OSD Rising Propagation Delay tr_pr (OSD) - 7 15 ns OSD Falling Propagation Delay tf_pr (OSD) - 9 20 ns Video/OSD 10kHz Isolation Iiso10K (OSD) - -60 -40 dB Video/OSD 10MHz Isolation Iiso10M (OSD) - -50 -35 dB OSD Output Black Level OSD Output Voltage OSD Output Vpp Attenuation Output Match between Channels 12 I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 I2C BUS Recommended Operating Conditions Table 8. I2C BUS Recommended Operating Conditions Parameter Symbol Min Typ Max Unit Input High Level Voltage VinH 3.0 - - V Input Low Level Voltage VinL - - 1.5 V SCL Clock Frequency fSCL - - 200 kHz Hold Time Before a new transmission can start tBUF 1.3 - - uS Hold Time for Start Condition tHDS 0.6 - - uS Set-up Time for Stop Conditions tSUP 0.6 - - uS The Low Period of SCL tLOW 1.3 - - uS The High Period of SCL tHIGH 0.6 - - uS Hold Time Data tHDAT 0.3 - - uS Set-up Time Data tSUPDAT 0.25 - - uS Rise Time of SCL tR - - 1.0 uS Fall Time of SCL tF - - 3.0 uS I2C BUS Timing Requirement tBUF tHDAT SDA tHDS SCL tSUPDAT tSUP tHIGH tLOW 13 S1D2500A01 I 2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS NOTES: 1. 2. Absolute Maximum Rating Indicates the limit beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional but do not guarantee specific performance limits. For guaranteed specifications and test conditions, See the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. 3. VCC supply pins 6, 9, and 23 must be externally wired together to prevent internal damage during VCC power on/off cycles. 4. The supply current specified is the quiescent current for VCC1/VCC2 and VCC3 with RL = . The supply current for VCC3 (pin 23) also depends on the output load. 5. Output voltage is dependent on load resistor. Test circuit uses RL = 390 6. Measure gain difference between any two amplifiers Vin = 560mVpp. 7. When measuring video amplifier bandwidth or pulse rise and fall times, a double sided full ground plane printed circuit board without socket is recommended. Video amplifier 10MHz isolation test also requires this printed circuit board. The reason for a double sided full ground plane PCB is that large measurement variations occur in single sided PCBs. 8. Adjust input frequency from 10MHz (AV max reference level) to the-3dB frequency (f -3dB). 9. Measure output levels of the other two undriven amplifiers relative to the driven amplifier to determine channel separation. Terminate the undriven amplifier inputs to simulate generator loading. Repeat test at fin = 10MHz for Iso_10MHz. 10. A minimum pulse width of 200 ns is guaranteed for a horizontal line of 15kHz. This limit is guaranteed by design. if a lower line rate is used a longer clamp pulse may be required. 11. During the AC test the 4V DC level is the center voltage of the AC output signal. For example. if the output is 4Vpp the signal will swing between 2V DC and 6V DC. 12. These parameters are not tested on each product which is controlled by an internal qualification procedure. 14 I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 FUNCTIONAL DESCRIPTION Contrast (OSD Contrast Adjustment) (8-bits) The contrast adjustment is made by controlling simultaneously the gain of three internal variable gain amplifiers through the I2C bus interface. The contrast adjustment allows you to cover a typical range of 38dB. Brightness Adjustment (8-bits) The brightness adjustment controls to add the same black level (pedestal) to the 3-channel/R/G/B signals after contrast amplifier by I2C BUS. Cut-Off Brightness Adjustments (8-bits) The Cut-Off Brightness adjustment is made by simultaneously controlling the external cut-off current. Cut-Off (SUB Contrast) Adjustment (8-bits x 3) These adjustments are used to adjust the white balance, and the gain of each channel is controlled by I2C BUS. The SUB contrast adjustment allows you to cover a typical range of 11dB. OSD Inputs The S1D2500A01 includes all the circuitry necessary to mix OSD signals into the R/G/B video signal. You need 4 pins for this function. (R/G/B OSD, OSD blanking) Serial Interface The 2-wires serial interface is an I2C BUS interface. The slave address of the S1D2500A01 is DC (hexadecimal) Bit8 Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 1 1 0 1 1 1 0 0 (W) Data Transfer All bytes are sent MSB (Most Significant Bit) bit first and the write data transfer is closed by a stop. The MCU can write data into the S1D2500A01 registers. To do that, after a start, the MCU must send: - The I2C address slave byte with a low level for R/W bit (bit1) - The byte of the interinal register address where the MCU wants to write data (SUB Address) - The data - Stop 15 I 2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 I2C BUS Write Operation MSB LSB SCL transter SDA START Slave address Register address ACK Data byte ACK ACK STOP Register Description Register Sub Address (Slave address: DCH) Sub Address (Hex) Register Names DAC bits Int. value (Hex) 00 Contrast control 8 bits 80 01 Brightness control (3-ch) 8 bits 80 02 SUB Contrast control (R) 8 bits 80 03 SUB Contrast control (G) 8 bits 80 04 SUB Contrast control (B) 8 bits 80 05 OSD Contrast control 8 bits 80 06 Cut-off Brightness control 8 bits 80 07 Cut-off control (R) 8 bits 80 08 Cut-off control (G) 8 bits 80 09 Cut-off control (B) 8 bits 80 0A HS2 l HS1 l CS3 l CS2 l CS1 l CT l HT l SBLK 20 HT: Video & OSD Half Tone ctrl switch (1: ON, 0: OFF) HS2/HS1: OSD Raster Color Switch for Video Half Tone (HT = 1) HS2 HS1 OSDR OSDG OSDB Half Tone 0 0 1 1 0 1 0 1 0 0 0 0 0 1 0 1 0 0 1 1 Black Green Blue Cyan CT: Cut-off Control INT/EXT (0:INT/1: EXT) select switch (DC/AC mode) CS1/CS2/CS3/: 80/160/320uA Cut-Off ctrl EXT offset current Switch (CT = 1) SBLK: Soft Blanking switch (1: ON, 0: OFF) 16 I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 Contrast Register (SUB ADRS: 00H) (Vin = 0.56Vpp, bright: 40H, subcont: FFH) Hex B7 B6 B5 B4 B3 B2 B1 B0 Contrast (Vpp) Gain (dB) 00 0 0 0 0 0 0 0 0 0 -30.0 80 1 0 0 0 0 0 0 0 1.12 11.5 FF 1 1 1 1 1 1 1 1 4.2 17.5 Increment/bit Int. value (Hex) O 0.0164 Brightness Register (3-ch) (SUB ADRS: 01H) (cont: 40H, subcont: FFH) Hex B7 B6 B5 B4 B3 B2 B1 B0 Brightness (Vpp) 00 0 0 0 0 0 0 0 0 0 80 1 0 0 0 0 0 0 0 2 FF 1 1 1 1 1 1 1 1 4 Increment/bit Int. value (Hex) O 0.0156 SUB Contrast Register (R/G/B-ch) (SUB ADRS: 02/03/04H) (Vin=0.56Vpp, bright: 40H, cont: FFH) Hex B7 B6 B5 B4 B3 B2 B1 B0 SUB Contrast (Vpp) Gain (dB) 00 0 0 0 0 0 0 0 0 1.33 7.5 80 1 0 0 0 0 0 0 0 2.65 13.5 FF 1 1 1 1 1 1 1 1 4.2 17.5 Increment/bit Int. value (Hex) O 0.0123 OSD Contrast Register (SUB ADRS: 05H) (VOSD = TTL, bright: 40H, subcont: FFH) Hex B7 B6 B5 B4 B3 B2 B1 B0 OSD Contrast (Vpp) Gain (dB) 00 0 0 0 0 0 0 0 0 0 - 80 1 0 0 0 0 0 0 0 3.7 - FF 1 1 1 1 1 1 1 1 3.5 - Increment/bit Int. value (Hex) O 0.0289 17 I 2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 Cut-Off Brightness Register (3-ch) (SUB ADRS: 06H) Hex B7 B6 B5 B4 B3 B2 B1 B0 Cut-Off Brightness (A) 00 0 0 0 0 0 0 0 0 0 80 1 0 0 0 0 0 0 0 75 FF 1 1 1 1 1 1 1 1 150 Increment/bit Int. value (Hex) O 0.588 Cut-Off Register (R/G/B-ch) (SUB ADRS: 07/08/09H) (cont = 80H, subcont: FFH, INT: CT=0, EXT: CT=1) Hex B7 B6 B5 B4 B3 B2 B1 B0 Cut-Off INT (V) Cut-Off EXT(A) 00 0 0 0 0 0 0 0 0 -0.5 0 80 1 0 0 0 0 0 0 0 0 250 FF 1 1 1 1 1 1 1 1 0.5 500 3.9mV 1.96 Increment/bit 18 Int. value (Hex) O I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 APPLICATION BOARD CIRCUIT VCC=12V 12V 0.1uF 100 Vin Vout 3 5V 2 1 KA78T05 GND + 100uF BU In ROSD In 33 1 33 2 33 3 ROSD B/U GOSD RCLP BOSD ROUT 28 0.1uF 27 0.1uF GOSD In Red Out BOSD In 26 390 VI/OSD SW In Red In 33 33 4 10uF 5 RIN GOUT 25 24 390 6 + 100uF GCLP Green Out + 75 VI/OSD_SW 0.1uF VCC1 VCC3 23 0.1uF + 100uF 0.1uF 7 GND1 GND3 22 KA2500 S1D2500A Green In 10uF 33 8 + 75 Blue In VCC2 BCLP 20 0.1uF 19 100 18 100 5V BLK In 10 + 75 21 0.1uF 10uF 33 Blue Out BOUT 390 9 + 100uF GIN BIN BLK GND(L) CLP ABL RCT CLP In 11 ABL In 75V 100 5V 2K 12 + 47uF 0.1uF 13 2K 17 75K SCL GCT SDA BCT 16 12V 75K BAV21 KSP92 14 100 SCL 15 + 1uF 100V KSP42 SDA + 0.47uF 2.2K 50V 100 75V 75K 100 12V 75K BAV21 1 SCLK KSP92 5V 1 14 2 13 3 12 1uF + 100V 3 ACK 4 4 11 5 10 6 9 7 8 KSP42 + 75V 0.47uF 2.2K 50V 75K 100 12V 75K BAV21 KSP92 1uF + 100V SCL SDA KSP42 + 2.2K 0.47uF 50V 74HCT125 2 SDAT 100 19 20 BLK CLP 10uF 12V + + 9 BIN 14 SDA SCL ABL 100 0.1uF 12 11 GND(L) 10 VCC2 13 + 47uF GND1 VCC1 8 GIN 7 6 100 100 VI/OSD_SW BOSD 5 RIN 4 3 KA2500 28 25 26 22 23 19 16 17 BCT 15 GCT RCT CLP 18 BLK BCLP 20 BOUT 21 GND3 VCC3 GOUT 24 GCLP ROUT RCLP 27 B/U BU 390 100 100 100 100 100 0.1uF + 390 0.1uF 390 0.1uF 0.1uF 100uF 100uF 0.1uF + 33 10uF 33 ROSD 2 GOSD 1 + GND BIN BOUT GND GOUT GND ROUT VEE GIN VCC RIN 75V 27 27 27 + 0.1uF 0.1uF 0.1uF 1uF 100V + 12V 1uF 100V + 75K KSP42 75K KSP42 KSP42 + 75K 12V 1uF 100V 12V 50V + 0.47uF KSP92 BAV21 0.47uF 50V + KSP92 BAV21 0.47uF 50V + KSP92 BAV21 75K 75V 75K 75V 75K 75V 2.2K 75 33 10uF 75 75 + SDA SCL ABL 33 33 33 33 100uF B In 0.1uF 2.2K G In R In OSD SW B OSD G OSD R OSD + 100uF VCC=12V B Out G Out To Cathode R Out S1D2500A01 I 2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS APPLICATION CIRCUIT 2.2K 0.1uF 100uF 0.1uF 0.1uF S1D2500A I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 CHARACTERISTICS CURVE Brightness (01H) Vout [V] Cut-off (07/08/09H): 80H 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 18mV/bit 0.0 0 10 20 30 40 50 60 70 80 90 A0 B0 C0 D0 E0 F0 Data Cut-Off Brightness Control (06H) Iout [uA] SW (0AH) : 04 200 180 160 140 120 100 80 60 40 20 0.7uA/bit 0 0 10 20 30 40 50 60 70 80 90 A0 B0 C0 D0 E0 F0 Data 21 I 2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 Int. Cut-Off Control (07/08/09H) Vout [V] Bright (01H): 80H 2.7 2.5 2.3 2.1 1.9 1.7 4.6mV/bit 1.5 0 10 20 30 40 50 60 70 80 90 A0 B0 C0 D0 E0 F0 Data Ext. Cut-Off Control (07/08/09H) Iout [uA] Cut-Off BRT (06H): 00H 600 500 400 300 200 100 2.14uA/bit 0 0 22 10 20 30 40 50 60 70 80 90 A0 B0 C0 D0 E0 F0 Data I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 Contrast Control (00H) Vout [Vpp] Vin = 560mVpp 5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 18.36mVpp/Bit 0 0 10 20 30 40 50 60 70 80 90 A0 B0 C0 D0 E0 F0 Data Contrast Control (00H) Vout [dB] Drive (02/03/04H): FF 30 20 10 0 -10 -20 -30 -40 -50 0 10 20 30 40 50 60 70 80 90 A0 B0 C0 D0 E0 F0 Data 23 I 2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 Drive Control (02/03/04H) Vin = 560mVpp, Contrast (00H): FFH Vout [Vpp] 4.5 4 3.5 3 2.5 2 1.5 1 0.5 12mVpp/Bit 0 0 10 20 30 40 50 60 70 80 90 A0 B0 C0 D0 E0 F0 Data Drive Control (02/03/04H) Vout [Vpp] Contrast (00H): FFH 20.00 18.00 16.00 14.00 12.00 10.00 8.00 6.00 0 24 10 20 30 40 50 60 70 80 90 A0 B0 C0 D0 E0 F0 Data I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 OSD Contrast Control (05H) Drive (02/03/04H): FFH Vout [Vpp] 8 7 6 5 4 3 2 1 28.6mV/bit 0 0 10 20 30 40 50 60 70 80 90 A0 B0 C0 D0 E0 F0 Data OSD Contrast Control (05H) Vout [dB] Drive (02/03/04H): FFH 30 20 10 0 -10 -20 -30 -40 -50 0 10 20 30 40 50 60 70 80 90 A0 B0 C0 D0 E0 F0 Data 25 I 2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 Vout [dB] Vout [dB] f-3dB (Video Preamp) 2 1 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -13 1 25 50 75 100 125 1 1.5 150 175 200 225 250 275 300 325 350 f[MHz] 0 -2 -4 -6 -8 -10 -12 0 0.5 2 2.5 3 3.5 4 4.5 VABL [V] 26 I2C BUS CONTROLLED R/G/B VIDEO AMPLIFIER FOR MONITORS S1D2500A01 Modulation Rat [%] BU Characteristic 25 20 15 10 5 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 VBU [Vpp] 27