Catalog 82012 Revised 10-09 TE (logo) and Tyco Electronics are trademarks of the Tyco Electronics group of companies and its licensors. tycoelectronics.com 82012-2.5M-CIS-FP-10-09 Ribbon Cable Interconnect Solutions Tyco Electronics Corporation Harrisburg, PA Ribbon Cable Interconnect Solutions Ribbon Cable Interconnect Solutions Ribbon Cable Connector Selection Guide .039" [1.00 mm] Cable Pitch Ribbon Cable Connector Selection Guide .025" [0.64 mm] Cable Pitch Mates to .050" x .100" 2-Row Pin Header Grid Pages 10 and 11 Mates to .100" x .100" 2-Row Pin Header Grid Page 15 Mates to .078" [2 mm] x .078" [2 mm] 2-Row Pin Header Grid Solders to .075" x .100" 4-Row PCB Layout See 5176264, 5178751 Series and Part Number 1775109 (Not in this Catalog) System 50 Receptacles Pages 8-11 Ultra ATA Bus Compliant Receptacles Pages 13-15 System 50 Paddleboard Page 12 2 mm Receptacle Connectors Pages 16 and 17 .050" [1.27 mm] Cable Pitch Mates to .50" x .50" Micro-MaTch Female Top Entry, 215079 Series, PCB Connector Page 34 Mates to .050" x .050" Micro-MaTch Female Side Entry, 215460 Series, PCB Connector Page 35 Mates to .050" x .050" Micro-MaTch Female Top Entry SMD, 188275 Series, PCB Connector Page 36 Solders directly to 2.54mm x 1.27mm Staggered 2 row PCB Footprint Male-on-Wire 215083 Series, Page 38 Male-on-Wire 215083 Series, Page 38 Male-on-Wire 215083 Series, Page 38 Paddle Board Connector, 215570 Series, Page 39 .050" [1.27 mm] Cable Pitch (Continued) Mates to .050" x .050" Right-Angle Headers Mates to .050" x .050" Vertical Headers 50/50 Grid Receptacle Connector with or without latch 50/50 Grid Receptacle Connectors without latch 2 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions PageHead_12_HelvCdBd Ribbon Cable Connector Selection (Continued) Guide (Continued) Ribbon Cable Connector Selection Guide .050" [1.27 mm] Cable Pitch (Continued) Mates to .100" x .100" Novo Type Female Socket Connector Pages 48-51 Mates to .100" x .100" 3-Row Eurocard Type C & R See Catalog 82721 Universal I/O Pin Connectors Pages 45 and 46 EUROLATCH Receptacles Page 47 Mates to .100" x .100" 2-Row Universal or Low-Profile Headers Pages 75-96 AMP-LATCH Novo Connectors Pages 48-51 622 and 636 Series Female Socket Connectors Pages 52 and 53 609 Series Female Socket Connectors Pages 54 and 55 .050" [1.27 mm] Cable Pitch (Continued) Mates to 2-Row DIP Sockets or Solders to PCB .100" x .100" Footprint 609 Series DIP Plugs Page 56 622 and 636 Series DIP Plugs Page 57 Tyco Electronics DIP Plugs Page 58 Solders to .050" x .100" 4-Row PCB Footprint .100" x .300" Footprint .100" x .600" Footprint Tyco Electronics DIP Plugs Page 59 Tyco Electronics DIP Plugs Page 60 Solder Transition Connectors Page 61 3 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Introduction Disclaimer While Tyco Electronics Corporation and its affiliates referenced herein ("Tyco Electronics") have made every reasonable effort to ensure the accuracy of the information in this catalog, Tyco Electronics does not guarantee that it is error-free, nor does Tyco Electronics make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. Tyco Electronics reserves the right to make any adjustments to the information contained herein at any time without notice. Tyco Electronics expressly disclaims all implied warranties regarding the information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. Tyco Electronics' only obligations are those in the Tyco Electronics Standard Terms and Conditions of Sale, and in no case will Tyco Electronics be responsible for any incidental, indirect, or consequential damages arising from the sale, resale, use, or misuse of its products. Users should independently evaluate the suitability of, and test each product for, their application. The dimensions, specifications, designs, construction, materials and processes in this catalog are for reference purposes only and are subject to change without notice. Please consult Tyco Electronics for the most current product information. The export of certain Tyco Electronics products is restricted by the Arms Export Control Act (Title 22, U.S.C. Sec 2751, et seq.) or the Export Administration Act of 1979, as amended (Title 50, U.S.C., App. 2401 et seq.). Orders may be subject to export approval by the U.S. Government. Buyer must comply with all applicable export laws of all applicable jurisdictions. (c) 2009, 1999, 1998, 1996, 1995, 1993, 1992, 1989, 1988, 1986, 1985, 1983, 1982, 1977, 1976, 1974 and 1973 Tyco Electronics Corporation. All Rights Reserved. AMP, AMPLIMITE, AMPMODU, ACTION PIN, AMP-LATCH, MICRO-MATCH, CHAMP, EUROLATCH, TE LOGO and TYCO ELECTRONICS are trademarks of the Tyco Electronics group of companies and its licensors.. Other products, logos, and company names mentioned herein may be trademarks of their respective owners. See inside back cover for Global Contacts and phone numbers. Restriction on the use of Hazardous Substances (RoHS) At Tyco Electronics, we're ready to support your RoHS requirements. We've assessed more than 1.5 million end items/components for RoHS compliance, and issued new part numbers where any change was required to eliminate the restricted materials. Part numbers in this catalog are identified as: RoHS Compliant -- Part numbers in this catalog are RoHS Compliant, unless marked otherwise. These products comply with European Union Directive 2002/95/EC as amended 1 January 2006 that restricts the use of lead, mercury, cadmium, hexavalent chromium, PBB, and PBDE in certain electrical and electronic products sold into the EU as of 1 July 2006. NOTE: For purposes of this Catalog, included within the definition of RoHS Compliant are products that are clearly "Out of Scope" of the RoHS Directive such as hand tools and other non-electrical accessories. NOTE: Information regarding RoHS compliance is provided based on reasonable inquiry of our suppliers and represents our current actual knowledge based on the information provided by our suppliers. This information is subject to change. For latest compliance status, refer to our website referenced at right. Getting the Information You Need Our comprehensive on-line RoHS Customer Support Center provides a forum to answer your questions and support your RoHS needs. A RoHS FAQ (Frequently Asked Questions) is available with links to more detailed information. You can also submit RoHS questions and receive a response within 24 hours during a normal work week. The Support Center also provides: I Cross-Reference from Non-compliant to Compliant Products I Ability to browse RoHS Compliant Products in our on-line catalog I Downloadable Technical Data Customer Information Presentation I More detailed information regarding the definitions used above I So whatever your questions when it comes to RoHS, we've got the answers at www.tycoelectronics.com/leadfree RoHS Customer Support Center 4 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Introduction (Continued) Mass termination capabilities of the ribbon cable connectors have helped make ribbon cable, and particularly .050 [0.127] centerline cable, popular within the electronics industry. The ability to terminate up to 64 conductors simultaneously, without stripping or otherwise pre-paring the cable, presents obvious labor savings. Ribbon Cable Connectors are wire-to-board devices used to make the transition between cable and pc board circuitry. They find heavy use within equipment to connect one board to another or one subsystem to another. The connectors are also used in input/output applications, connecting different pieces of equipment. Ribbon Cable Solutions are available on three separate cable centerline spacings. They include: .025 [0.64] Centerlines I System 50 receptacles I System 50 paddleboards I Pin headers .039 [1.00] Centerlines I 2.0 mm receptacles I Breakaway pin headers .050 [1.27] Centerlines I 50/50 Grid connectors I Micro-MaTch connectors I AMP-LATCH novo receptacle connectors I DIP plugs I EUROLATCH receptacle connectors per DIN 41612 and IEC 603-2 I Pin Headers System 50 ribbon cable receptacles will terminate cable on .025 [0.64] centerlines. They are available in select sizes from 20 thru 100-positions, and accept wire size range 30 AWG [0.05 mm2] solid or stranded wire and 32 AWG [0.03 mm2] stranded pvc insulated wire. Housing and cover are made of high temperature tolerant thermoplastic material, black, UL 94V-0 rated. A single mating beam, phosphor bronze contact provides the interconnect between the conductor and the .0152 [0.382] posts on .050 x .100 [1.27 x 2.54] grid. Also available in paddleboard configurations. 2.0 mm [.079] ribbon cable receptacles feature contacts on a true 2.0 mm [.079 in.] mating grid for 1.0 mm [.039 in.] pitch ribbon cable. Select configurations are available between 8 and 50-positions. Receptacles feature insulation displacement contacts (IDC). 50/50 Grid connectors Although AMPMODU 50/50 grid vertical headers and Receptacles are designed for parallel board-to-board stacking in high density applications, Right-angle board-to-board and cableto-board applications are also possible since the vertical receptacles also mate with non-latching right-angle headers and the vertical headers also mate with non-latching cable connectors. Micro-Match connectors Miniaturization and the trend towards higher density of electronic functions on a substrate led to the introduction of the Micro-MaTch connector. The system offers a range of board and wire connectors, enabling a variety of wire-to-board and board-to-board interconnections. Its design prevents the traditional failure mode in tin-plated connections, fretting corrosion. An additional positioning spring in the female part absorbs relative movements caused by vibrations and thermal expansion between male and female contacts. By preventing movements on the contact spot, a gas tight connection can be guaranteed under all circumstances. AMP-LATCH novo receptacles feature two rows of contacts on .100 x .100 [2.54 x 2.54] centers on selected sizes of 10 thru 64-positions and mate with .025 [0.64] square or round posts. The AMP-LATCH novo tuningfork contact offers a military-approved design, at an affordable cost. Polarization options include military, center and military, or dual bar. DIP (Dual In-Line Package) plugs provide a permanent connection of ribbon cable to a pc board or mating to DIP sockets. Using the same centerline dimensions as DIP integrated circuits, DIP plugs offer space efficiency and a low profile of .253 [6.43]. Need more information? Call Technical Support at the numbers listed below. Technical Support is staffed with specialists well versed in all Tyco Electronics products. They can provide you with: I Technical Support I Catalogs I Technical Documents I Product Samples I Tyco Electronics Authorized Distributor Locations 5 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Table of Contents Ribbon Cable Connector Selection Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2, 3 .025 [0.64] Centerline Ribbon Cable Connectors System 50 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12 Cable-to-Board Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 9, 12 Board-to-Board Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 11 Ultra ATA compliant Bus Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-15 .039 [1.00] Centerline Ribbon Cable Connectors 2 mm [.079] Receptacle Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 17 AMPMODU 50/50 Grid Connector System Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Board-to-Board Vertical Receptacles and Headers . . . . . . . . . . . . . . . . . . . . . . . . . . . . Board-to-Board Vertical Receptacles, Double Row, .050 x .050 [1.27 x 1.27] Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Board-to-Board Vertical Headers, Double Row, .050 x .050 [1.27 x 1.27] Centers . . Recommended PC Board Layouts for Vertical Connectors . . . . . . . . . . . . . . . . . . . . Board-to-Board Right-Angle Headers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Board-to-Board Right-Angle Headers, Double Row, .050 x .050 [1.27 x 1.27] Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cable-to-Board Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cable-to-Board Receptacle Connectors, Double Row, .050 x .050 [1.27 x 1.27] Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Terminating Covers for Cable Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Application Tooling for Cable Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Performance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Technical Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Micro-MaTch Connector System Miniature Connector System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Overview/Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Applications (3 Dimensions) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Applications (2 Dimensions) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Female-on-Board Connector, Top Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Female-on-Board Connector, Side Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Female-on-Board Connector Surface Mount Device (SMD) . . . . . . . . . . . . . . . . . . . . . Male-on-Board Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Male-on-Wire Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Paddle Board Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Crimp On Snap In (COSI) Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Application Tooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42, Lead Assembly and Sample Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 19 20 21 22 23 24 25 26 27 28 29 29 30 31 32 33 34 35 36 37 38 39 40 41 43 44 .050 [1.27] Centerline Ribbon Cable Connectors Universal I/O Pin Connectors without Mounting Ears . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Universal I/O Pin Connectors with Slotted Mounting Ears . . . . . . . . . . . . . . . . . . . . . . . 46 EUROLATCH Receptacles 64-Position (Three-Row Housings, Two Rows Loaded) . . . 47 AMP-LATCH Novo Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-51 Military Polarized, .100 x .100 [2.54 x 2.54] Centers . . . . . . . . . . . . . . . . . . . . . . . . . 49 Center and Military Polarized, .100 x .100 [2.54 x 2.54] Centers . . . . . . . . . . . . . . . . 50 Dual Polarized, .100 x .100 [2.54 x 2.54] Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Female Socket Connectors, .100 x .100 [2.54 x 2.54] Centers, 622 and 636 Series . . 52, 53 Female Socket Connectors, .100 x .100 [2.54 x 2.54] Centers, 609 Series . . . . . . . . . 54, 55 DIP Plugs, .100 x .100 [2.54 x 2.54] Centers, 609 Series . . . . . . . . . . . . . . . . . . . . . . . 56 DIP Plugs, .100 x .100 [2.54 x 2.54] Centers, 622 Series . . . . . . . . . . . . . . . . . . . . . . . 57 6 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Table of Contents (Continued) .050 [1.27] Centerline Ribbon Cable Connectors (Continued) DIP Plugs, .100 x .100 [2.54 x 2.54] Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DIP Plugs, .100 x .300 [2.54 x 7.62] Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DIP Plugs, .100 x .600 [2.54 x 15.24] Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-Row PCB Solder Transition Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-Row Horizontal Receptacle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accessories Flexible Pull Tabs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Universal I/O Latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Military Polarizers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Keying Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Strain Relief for 622 Series DIP Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pull Loops, Permanent (For Receptacles and Pin Connectors) . . . . . . . . . . . . . . . . . . . Strain Relief for Universal I/O without Mounting Ears . . . . . . . . . . . . . . . . . . . . . . . . . . . Strain Relief for 609 Series (Tulip Contact) Female Socket Connectors . . . . . . . . . . . . Strain Relief for AMP-LATCH Novo and Ultra ATA compliant Bus Connectors . . . . . . . Strain Relief for 2 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Strain Relief for 622 and 636 Series Female Socket Connectors . . . . . . . . . . . . . . . . . 58 59 60 61 62 63 63 63 64 65 66 67 67 68 68 69 Application Tooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70-74 Low Profile Headers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75-83 Low Profile Pin Headers, Center and Dual Polarized, .100 x .100 [2.54 x 2.54] Centerlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76, 77 Low Profile Pin Headers, Center and Dual Polarized, .100 x .100 [2.54 x 2.54] Centerlines and "Kinked" Solder Tails for PCB Retention . . . . . . . . . . . . . . . . . . . 78, 79 IDC Low Profile Ejection Style Pin Headers with Die Cast Ejection Latches, Military and Center Polarized, .100 x .100 [2.54 x 2.54] Centerlines . . . . . . . . . . 80, 81 IDC Low Profile Ejection Style Pin Headers, Center Polarized, .100 x .100 [2.54 x 2.54] Centerlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82, 83 Universal Ejection Style Pin Headers and Pinless Headers Universal Ejection Style Pin Headers, Military, Center and Dual Polarized, .100 x .100 [2.54 x 2.54] Centerlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84-86 Universal Ejection Style Pin Headers, ACTION PIN Contacts, Military, Center and Dual Polarized, .100 x .100 [2.54 x 2.54] Centerlines . . . . . . . . . . . . 87, 88 Universal Ejection Style Pin Headers, Military, Center and Dual Polarized, .100 x .100 [2.54 x 2.54] Centerlines, Right-Angle . . . . . . . . . . . . . . . . . . . . . . . . 89-91 Universal Ejection Style Pinless Headers, Military, Center and Dual Polarized, .100 x .100 [2.54 x 2.54] Centerlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92, 93 Universal Ejection Style Pin Headers, with PCT Housing, .100 x .100 [2.54 x 2.54] Centerlines, .025 [0.64] Sq. Posts (Mating End) . . . . . . . . . . . . . . . 94, 95 Latches for Ejection Style Universal Pin Headers and Pinless Headers . . . . . . . . . . . . 96 Cable Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97, 98 Part Number Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 7 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions System 50 Cable-to-Board Connectors, .025 [0.64] Centerline Ribbon Cable Product Facts I I .025 [0.64] Centerline Ribbon Cable Connectors System 50 Cable-to-Board Connectors I I I I I I Preassembled housing and cover One-step termination End and daisy chain termination Positive end latching of connector to universal header Terminates 30 AWG [0.05 mm2] solid or stranded and 32 AWG [0.03 mm2] stranded .025 [0.64] centerline ribbon cable with PVC insulation Connectors are RoHS compliant Recognized under the Component Program of the Underwriters Laboratories, Inc. UL File No. E28476 Certified by the Canadian Standards Association, File No. LR 7189 R R The System 50 Ribbon Cable connector is a receptacle connector that will terminate ribbon cable on .025 [0.64] centerlines. It is available in select sizes from 10 to 100 positions and will accommodate 30 AWG [0.05 mm2] solid or stranded and 32 AWG [0.03 mm2] stranded conductors with PVC cable insulation. The housing and cover are of a high temperature tolerant thermoplastic (black) with a UL 94V-0 rating. A phosphor bronze single mating beam contact provides the interconnect between the conductor and the .015 [0.38] square posts on the .050 x .100 [1.27 x 2.54] grid. The contacts are plated with 30 gold duplex plating. The latching feature is located on the receptacle, not the header, and saves board space and eliminates future problems of "latch height compatibility." 8 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions System 50 Cable-to-Board Connectors, .025 [0.64] Centerline Ribbon Cable (Continued) Double Row Receptacle .254 .228 [6.45] [5.79] A .054 [1.37] .430 [10.92] Material and Finish Housing -- Black thermoplastic, UL 94V-0 rated Latches -- Stainless steel Contacts -- Phosphor bronze, plated 30 microinch gold over nickel with tin in termination area .025 [0.64] Centerline Ribbon Cable Connectors System 50 Cable-to-Board Connectors .580 [14.73] Before Termination Cover B Latch C .198 [5.03] .228 [5.80] .246 [6.25] .100 [2.54] Contact .335 [8.51] Housing .102 [2.59] E Position #1 Indicator F .100 [2.54] Related Product Data Mateable Connectors -- See Tyco Electronics Catalog 82178 See Part Numbers 104068 and 104069 Series on pages 10 and 11 Mates with Posts -- .015 [0.38] square, .125 [3.18] long, on .050 x .100 [1.27 x 2.54] grid Technical Documents Product Specification 108-1109 Application Specification 114-25029 .050 Typ. [1.27] D No. of Pos. 10 14 16 20 24 26 30 34 40 44 50 60 64 68 72 80 100 A .510 12.95 .610 15.49 .660 16.76 .760 19.30 .860 20.32 .910 23.11 1.010 25.65 1.110 28.19 1.260 32.00 1.360 34.54 1.510 38.35 1.760 44.70 1.860 47.24 1.960 49.78 2.060 52.32 2.260 57.40 2.760 70.10 B .445 11.30 .545 13.84 .595 15.11 .695 17.65 .795 20.19 .845 21.46 .945 24.00 1.045 26.54 1.195 30.35 1.295 32.89 1.445 36.70 1.695 43.05 1.795 45.59 1.895 48.13 1.995 50.67 2.195 55.75 2.695 68.45 Dimensions C D .225 .200 5.72 5.08 .325 .300 8.26 7.62 .375 .350 9.52 8.89 .475 .450 12.07 11.43 .575 .550 14.61 13.97 .625 .600 15.88 15.24 .725 .700 18.42 17.78 .825 .800 20.96 20.32 .975 .950 34.54 24.13 1.075 1.050 27.31 26.67 1.225 1.200 31.12 30.48 1.475 1.450 37.47 36.83 1.575 1.550 40.00 39.37 1.675 1.650 42.55 41.91 1.775 1.750 45.08 44.45 1.975 1.950 50.17 49.53 2.475 2.450 62.87 62.23 E .096 2.44 .146 3.71 .171 4.34 .221 5.61 .271 6.88 .296 7.52 .346 8.79 .396 10.06 .471 11.96 .521 13.23 .596 15.14 .721 18.31 .771 19.58 .821 20.85 .871 22.12 .971 24.66 1.221 31.01 F .294 7.47 .394 10.01 .444 11.28 .544 13.82 .644 16.36 .694 17.63 .794 20.17 .894 22.71 1.044 26.52 1.144 29.06 1.294 32.87 1.544 39.22 1.644 41.76 1.744 44.30 1.844 46.84 2.044 51.92 2.544 64.62 Part Number 2-111196-5 2-111196-6 2-111196-7 1-111196-8 2-111196-8 2-111196-9 1-111196-9 3-111196-0 2-111196-0 3-111196-1 2-111196-1 2-111196-2 3-111196-2 3-111196-4 2-111196-3 3-111196-3 2-111196-4 See Application Specification for termination tooling. Note: All part numbers are RoHS compliant. 9 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions System 50 Board-to-Board Connectors, Through-Hole Headers Shrouded, Double Row Vertical .015 [0.38] .390 [9.91] .025 [0.64] Centerline Ribbon Cable Connectors System 50 Board-to-Board Connectors .055* [1.40] .060 [1.52] 2 Plc. Circuit Identification Feature** A .050 [1.27] Typ. .092 [2.34] .100 [2.54] Material and Finish Housing -- Black thermoplastic, UL 94V-0 rated Contacts -- Copper alloy, plated .000030 [0.00076] gold in mating area, .000150 [0.00381] tin on solder posts, with entire contact underplated .000050 [0.00127] nickel .284 [7.21] .344 [8.74] .100 [2.54] Related Product Data Mateable Receptacles -- page 9 Technical Documents Product Specification 108-1093 Application Specification 114-25031 No. of Positions 10 12 14 16 20 24 26 30 Dim. A .380 9.65 .430 10.92 .480 12.19 .530 13.46 .630 16.00 .730 18.54 .780 19.81 .880 22.35 Part Number No. of Positions 5-104068-2 34 5-104068-8 40 5-104068-9 44 6-104068-0 50 5-104068-1 60 6-104068-1 68 6-104068-2 72 5-104068-3 80 **Point of measurement for gold thickness. **Circuit identification feature omitted on 8, 10, 12 and 14 position headers. Note: All part numbers are RoHS compliant. 100 Dim. A .980 24.89 1.130 28.70 1.230 31.24 1.380 35.05 1.630 41.40 1.830 46.48 1.930 49.02 2.130 54.10 2.630 66.80 Part Number 6-104068-3 5-104068-4 6-104068-4 5-104068-5 5-104068-6 6-104068-8 6-104068-5 6-104068-6 6-104068-7 10 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions System 50 Board-to-Board Connectors, Through-Hole Headers (Continued) Shrouded, Double Row Right-Angle .100 [2.54] at Post Tips .055* [1.40] .160 [4.06] at Post Tips .540 [13.72] .025 [0.64] Centerline Ribbon Cable Connectors System 50 Board-to-Board Connectors .408 [10.36] Hold down post .060 [1.52] 2 Plc. Circuit Identification Feature** .100 [2.54] A Material and Finish Housing -- Black thermoplastic, UL 94V-0 rated Contacts -- Copper alloy, plated .000030 [0.00076] gold in mating area, .000150 [0.00381] tin on solder posts, with entire contact underplated .000050 [0.00127] nickel .050 Typ. [1.27] .290 [7.37] Related Product Data .350 [8.89] Mateable Receptacles -- page 9 Technical Documents .100 [2.54] Product Specification 108-1093 Application Specification 114-25031 Note 2 Note 1 No. of Positions 8 10 20 24 26 30 34 Dim. A .330 8.38 .380 9.65 .630 16.00 .730 18.54 .780 19.81 .880 22.35 .980 24.89 Part Number No. of Positions 5-104069-8 40 5-104069-4 50 5-104069-1 60 6-104069-2 68 6-104069-3 72 5-104069-5 80 6-104069-4 100 Dim. A 1.130 28.70 1.380 35.05 1.630 41.40 1.830 46.80 1.930 49.02 2.130 54.10 2.630 66.80 Part Number 5-104069-6 5-104069-2 5-104069-7 6-104069-8 6-104069-6 5-104069-3 6-104069-7 **Point of measurement for gold thickness. **Circuit identification feature omitted on 8, 10, 12 and 14 position headers. Notes: 1. Hold down posts located as shown for 16 through 100 position headers. Notes: 2. Hold down posts located as shown for 8 through 14 and 60 through 100 position headers. Notes: 3. All part numbers are RoHS compliant. 11 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions System 50 Cable-to-Board Connectors, .025 [0.64] Centerline Ribbon Cable Paddleboard A .273 [6.93] (Terminated) Material and Finish .025 [0.64] Centerline Ribbon Cable Connectors System 50 Cable-to-Board Connectors Housing -- LCP thermoplastic, UL 94V-0 rated, black Cover -- Polyester, UL 94V-0 rated, black Contacts -- Phosphor bronze, plated .000100 [0.00245] min. tin over .000050 [0.00127] min. nickel underplating Technical Documents Product Specification 108-1109 Application Specification 114-25040 .050 [1.27] Position 1 Indicator .168 [4.27] .100 [2.54] .020 [0.51] .024 Typ. .050 Typ. [1.27] [0.61] B .008 [0.20] Typ. .040 [1.02] .075 Typ. [1.91] Printed Circuit Board Hole Layout #1 14 1 16 2 20 2 24 2 26 1 28 2 30 1 34 1 40 2 .031 Typ. [0.79] .050 Typ. [1.27] .304 [7.72] .075 Typ. [1.91] 1 .030 Standoffs [0.76] (Various Locations) B .031 Typ. [0.79] .304 [7.72] 10 .304 [7.72] .118 [3.00] B PCB Layout .075 Typ. [1.91] .045 [1.19] Ref. .050 Typ. [1.27] No. of Pos. .340 [8.64] (Unterminated) Dimensions A B .436 .200 11.07 5.08 .536 .300 13.61 7.62 .586 .350 14.88 8.89 .686 .450 17.42 11.43 .786 .550 19.96 13.97 .836 .600 21.23 15.24 .886 .650 22.50 16.51 .936 .700 23.77 17.78 1.036 .800 26.31 20.32 1.186 .950 30.12 24.13 Part Number Printed Circuit Board Hole Layout #2 No. of Pos. PCB Layout 5111595-1 44 2 5111595-2 46 1 5111595-3 50 1 5111595-4 60 2 5111595-5 64 2 5111595-6 68 2 2-5111595-0 72 2 5111595-7 80 2 5111595-8 100 2 5111595-9 Dimensions A B 1.286 1.050 32.66 26.67 1.336 1.100 33.93 27.94 1.436 1.200 36.47 30.48 1.686 1.450 42.82 36.83 1.786 1.550 45.36 39.37 1.886 1.650 47.90 41.91 1.986 1.750 50.44 44.45 2.186 1.950 55.52 40.53 2.686 2.450 68.22 62.23 Part Number 1-5111595-0 1-5111595-7 1-5111595-1 1-5111595-2 1-5111595-3 1-5111595-9 1-5111595-4 1-5111595-5 1-5111595-6 See Application Specification for termination tooling. Note: All part numbers are RoHS compliant. 12 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Ultra ATA Compliant Bus Connectors, .025 [0.64] Centerline Ribbon Cable Product Facts I I I I I I I I I I Backward compatible with current IDE Interfaces Improved signal integrity: 1 to 1 signal to ground ratio Improved crosstalk when compared to existing IDE Cable Assembly .025 [0.64] Centerline Ribbon Cable Connectors Ultra ATA Compliant Bus Connectors I IDC termination Color coded connectors for "System board," and "Master HDD" and "Slave HDD" Cable impedance 80 ohms Up to 3 connectors per cable assembly 15 microinches gold plating Recognized under the Component Program of the Underwriters Laboratories, Inc. UL File No. E28476 Certified by the Canadian Standards Association, File No. LR 7189 R R Terminates 30 AWG solid or stranded PVC insulated 80 conductor ribbon cable Ultra ATA is the next generation IDE (Integrated Drive Electronics) bus. The current IDE bus has a maximum data transfer rate of about 16.5 MB/second. As the bus speeds and disk drive performances increase, the cable assembly between the motherboard and hard drive becomes a limiting factor in data transfer from the drive. The Ultra ATA compliant connector and cable assembly from Tyco Electronics provide the customer with improved electrical performance by creating a 1:1 signal-toground ratio. The connector design incorporates an IDC bus bar to common the 40 additional ground signals. The cable is .025" centerline PVC ribbon cable. The connector is fully backward compatible with existing 40position headers with pin 20 removed on mother- boards and disk drives. The new connectors are color coded to identify: 1. system board connector 2. primary or master hard drive connector 3. slave drive connector Standard Issues The Ultra ATA compliant cable performance specification is part of the Small Form Factor Committee No. 8049. Contacts Available: I 80 position IDC contact terminations I 40 signal contacts I 40 ground terminations to special IDC bus bar 13 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Ultra ATA Compliant Bus Connectors, .025 [0.64] Centerline Ribbon Cable Related Product Data .420 [10.67] Strain Relief -- Part Number 499252-1 Mateable Headers -- page 15 .492 Max. [12.50] Terminated View 2.186 [55.52] Material & Finish .240 [6.10] Cover Ground Bus Bar Housing Pos. No. 1 Indicator .610 Ref. [15.49] Odd Gnd .025 [0.64] Centerline Ribbon Cable Connectors Ultra ATA Compliant Bus Connectors Housing and Cover -- Thermoplastic, UL 94 V-0 rated, color per table Contacts -- Phosphor bronze, plated gold per table on mating end, .000050 [0.00127]min. tin in wire termination area, over .000050 [0.00127] min nickel on entire contact. Optional Center* Polarizer Bar Signal Contacts Contact Technical Documents Product Specification 108-1740 Application Specification 114-40056 See Application Specification for termination tooling. Accessories Strain Relief -- page 68 Keying Plug -- page 64 Pull Loops -- page 66 Pull Tabs -- page 63 Connector Type "System" Board "Primary" or "Master" "Slave" .100 [2.54] .100 [2.54] Circuit 20 Molded Shut 1.90 [48.26] Position 1 Color Coded Conductor No. 1 Position 1 Position 1 Pin 34 Conductor Cut per SFF-8049 Configuration A "System" Board Connector "Master" or "Primary" Connector "Slave" Connector Configuration B "System" Board Connector "Slave" Connector "Master" or "Primary" Connector *Center & Military Polarized Housing Color 1658619-2 Blue 1658619-1 Black 1658619-3 Gray 15" Gold Cover Color Black Black Black 15" Gold 1658618-2 1658618-1 1658618-3 Military Polarized Housing Color Blue Black Gray Cover Color Black Black Black Notes: 1. All connectors are "ODD GROUND" configuration, ie. all odd cable conductors are grounded. "EVEN GROUND" connectors are not available. See Customer Drawings for detailed electrical connection descriptions. 2. All part numbers are RoHS compliant. 14 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Ultra ATA Compliant Bus Connectors, .025 [0.64] Centerline Ribbon Cable (Continued) Ultra ATA Compatible Headers Universal Headers -- Pin 20 Omitted Post Type Housing Material Latch Type Part Number Contact Finish (Plating Code) Vertical Nylon or PBT Long 5111824-9 D Vertical Nylon or PBT Short 6489700-1 B Contact Finish (Plating Code) Solder Tail Length .110 2.79 .123 3.12 Comments PP Legend: PP -- Polarization Peg Post Type Housing Material Latch Type Part Number Vertical Nylon None 1888188-1 A Vertical Nylon None 1888188-2 B Vertical Nylon 6T None 2-1734161-4 C Vertical Nylon 6T None 2-1734161-5 C Vertical Nylon None 1734162-2 C Vertical Nylon None 1734162-4 C Solder Tail Length .120 3.05 .120 3.05 .122 3.10 .122 3.10 .110 2.79 .110 2.79 .025 [0.64] Centerline Ribbon Cable Connectors Ultra ATA Compliant Bus Connectors Low Profile Headers -- Pin 20 Omitted Housing Color Black Black Black Blue Black Blue Plating Code A -- Duplex plated, gold flash on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel. Plating Code B -- Duplex plated, gold flash over palladium-nickel, .000015 [0.00038] min. total on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel or .000015 [0.00038] min. gold on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel. Plating Code C -- Gold flash over nickel underplate on entire post. Plating Code D -- Duplex plated, gold flash over palladium-nickel, .000030 [0.00076] min. total on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel or .000015 [0.00038] min. gold on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel. Note: All part numbers are RoHS compliant. 15 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 METRIC Dimensions are Ribbon Cable Interconnect Solutions 2.0 mm [.079] Receptacle Connectors Product Facts I I I .039 [1.00] Centerline Ribbon Cable Connectors .079 [2.00] Receptacle Connectors I I I I I I I I True hard metric 2.0 x 2.0 [.079 x .079] mating grid for 1.0 [.039] pitch ribbon cable Wide selection of configurations, 8-50 positions Insulation displacement (IDC), beryllium copper contacts, duplex plated gold-over-nickel Top/bottom single beam contact orientation UL 94V-0 rated thermoplastic components Assemblies are furnished preassembled with termination covers Optional polarization Optional strain relief available Connector assemblies packaged for ease of handling and protection Recognized under the Component Program of the Underwriters Laboratories, Inc. UL File No. E28476 Certified by the Canadian Standards Association, File No. LR 7189 Performance Data Durability -- 150 cycles Termination Resistance -- 25 milliohms max. Mating Force -- 1.67 N max. per contact Unmating Force -- 0.14 N min. per contact Operating Temperature -- -65C to +105C Technical Documents Product Specification 108-1372 Application Specification 114-40038 R R The 2.0 [.079] receptacle connector family features contacts on a true 2.0 x 2.0 [.079 x .079] mating grid for 1.0 [.039] pitch 28 AWG ribbon cable. A variety of configurations are available from 8 through 50 positions. This small, compact connector is finding wide acceptance throughout the electronic industry, particularly in the smaller laptop and notebook type computers with 63.5 [2.5] drives. Other areas of application include point-of-sale terminals, fax machines, photocopiers, printers, consumer electronics, and other computer peripheral equipment. These receptacles feature insulation displacement contacts (IDC) with a top/bottom single-beam contact orientation. Contacts are beryllium copper, duplex plated 0.00076 [.000030] gold in the mating area and 0.00254 [.000100] min. tin on termination end, all over 0.00127 [.000050] nickel underplating. Contact mating area is 1.54 [.061] from the face of the housing and they accept 0.50mm [.0197] round or square posts. Housings are made of UL 94V-0 rated polyester with optional center bar polarization. Complete assemblies are furnished preassembled with termination covers. The complete assembly presents a compact design only 5.2 [.203] wide over the termination cover by 4 [.157] deep by 4 [.157] wide mating end. Terminated height is 8.48 [.334]. Optional strain relief available. Assemblies are packaged for ease of handling and protection. 16 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 METRIC Dimensions are Ribbon Cable Interconnect Solutions 2.0 mm [.079] Receptacle Connectors, Non-Polarized and Center Polarized Bar Material and Finish A Housing and Termination Cover -- UL 94V-0 rated polyester, black Contacts -- Beryllium copper, duplex plated 0.00076 [.000030] min. gold on mating end, 0.00013 [.000005] min. gold on termination end, all underplated 0.00127 [.000050] min. nickel Note: Accepts 0.08-0.09mm2 [28 AWG] ribbon cable, PVC insulated 1.00 [.039] pitch. See Application Specification for details. 5.16 [.203] Optional Center Polarizer Bar .039 [1.00] Centerline Ribbon Cable Connectors .079 [2.00] Receptacle Connectors 1.54 [.061] 10.24 [.403] Technical Documents Product Specification 108-1372 Application Specification 114-40038 4.000 [.1575] 5.00 [.197] Position Number 1 Indicator B Mateable Connectors -- pages 9 and 12, or see Application Specification for header requirements Position Number 1 1.90 0.05 [.075 .002] 2.00 [.079] Typ. Accessories 8.48 [.334] Pull Loops -- page 66 Keying Plugs -- page 64 Strain Relief -- page 68 2.00 [.079] Typ. Terminated View, Typical No. of Positions 8 10 12 14 16 20 22 24 26 30 34 40 44 50 Dimensions A B 13.18 8.41 .519 .331 15.16 10.41 .597 .410 17.15 12.40 .675 .488 19.18 14.40 .755 .567 21.18 16.41 .834 .646 25.17 20.40 .991 803 27.18 22.40 1.070 .882 29.18 24.41 1.149 .961 31.17 26.42 1.227 1.040 35.18 30.40 1.385 1.197 39.17 34.42 1.542 1.355 45.19 40.41 1.779 1.591 49.17 44.40 1.936 1.748 55.17 50.39 2.172 1.984 Center Polarized Non-Polarized 3-111623-0 2-111626-4 1-111623-8 1-111626-7 3-111623-1 -- 1-111623-9 1-111626-8 2-111623-0 2-111626-5 2-111623-1 1-111626-9 2-111623-9 -- 2-111623-7 2-111626-6 2-111623-2 2-111626-7 2-111623-3 -- 2-111623-8 2-111626-0 2-111623-4 2-111626-1 2-111623-5 2-111626-2 2-111623-6 2-111626-3 Note: All part numbers are RoHS compliant. 17 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions AMPMODU 50/50 Grid Connector System Right-Angle Headers, Board-to-Board (Page 24) Vertical Headers, Board-to-Board (Page 21) Receptacles, Cable-to-Board, With Latch (Page 26) Board-to-Board Vertical Receptacles and Headers Vertical Receptacles, Board-to-Board (Page 20) Receptacles, Cable-to-Board Without Latch (Page 26) Vertical Headers, Board-to-Board (Page 21) Vertical Headers, Board-to-Board (Page 21): .250 [6.35] Stack Height .320 [8.13] Stack Height .390 [9.91] Stack Height Vertical Receptacles, Board-to-Board (Page 20) Produced under a Quality Management System certified to ISO 9001 A copy of the certificate is available upon request. ISO900e1d i rtif Ce 18 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Board-to-Board Vertical Receptacles and Headers Product Facts Surface-mount R R AMPMODU 50/50 Grid Vertical Headers and Receptacles are designed for parallel board-to-board stacking in high density applications. Right-angle board-to-board and cable-to-board applications are also possible, since the vertical receptacles also mate with non-latching right-angle headers (page 24) and the vertical headers also mate with non-latching cable connectors. Available are double row, vertical shrouded headers and receptacles in sizes ranging from 10 through 100 positions (in 10 position increments). Parallel board-to-board stack heights of .250 [6.35], .320 [8.13] and .390 [9.91] are achievable by selection of the appropriate header. The receptacle is the same for all three stack height headers. PC boards and allow surface mounting to both sides of the board. In addition to providing retention during processing, the holddowns are soldered during reflow and therefore provide long-term strain relief for the solder joints. and packaging methods result in a system that is compatible with robotic assembly. AMPMODU 50/50 Grid Vertical Headers and Receptacles are designed to be compatible with standard surface-mount processes; IR (infrared) and VPR (vapor phase reflow). The surface-mount connectors have been designed so that dimensioning, tolerances, referenced datums, holddown characteristics Three Board Stack Heights Board-to-Board Vertical Receptacles and Headers products for parallel board-to-board applications, as well as right-angle board-to-board and cable-to-board applications High density .050 x .050 [1.27x1.27] centerline grid Three board-to-board stack heights: .250 [6.35], .320 [8.13] and .390 [9.91] Non-protrusive metallic holddowns Reliable dual beam receptacle contacts for redundant contact Duplex plated receptacle and post contacts; gold plated on mating areas, tin plated on tails Compatible with standard surface-mount processing (VPR and IR) Receptacle and header allow for drainage of processing fluids Tape and reel packaging available. Contact Tyco Electronics for details Polarized header and receptacle assemblies Sizes of 10, 20, 30, 40, 50, 60, 70, 80 and 100 positions Recognized under the Component Program of Underwriters Laboratories Inc., File No. E28476 Certified by Canadian Standards Association File No. LR7189 The headers and receptacles feature polarization to prevent misalignment. .250.006 [6.350.15] .320.006 [8.130.15] Non-Protrusive Metallic Holddowns .390.006 [9.910.15] Non-protrusive metallic holddowns are designed for use in .062 [1.57] or thicker 19 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Board-to-Board Vertical Receptacles, Double Row, .050 x .050 [1.27 x 1.27] Centerline A .120 [3.05] .028 [0.71] Material and Finish .050 [1.27] Vertical Receptacles, Double Row Housing--Glass-filled thermoplastic, black, 94V-0 rated Contacts--Copper alloy; duplex plated .000030 [0.00076] gold in mating area, .000150 [0.00381] tin on solder tail, with entire contact underplated .000050 [0.00127] nickel Holddown--Copper alloy; plated .000150 [0.00381] tin over .000050 [0.00127] nickel Polarizing Tab (For Polarization to Mating Header) .187 [4.75] .050 [1.27] .050 [1.27] Related Product Data Mating Headers -- pages 21 and 24 PC Board Layouts -- page 22 Performance Specifications -- page 29 Technical Documents -- page 29 Product Specification 108-1332 Application Specification 114-7010 Packaging -- Tube or Tape and Reel No. of Pos. 10 20 30 40 50 60 70 80 100 Dimension A .266 .516 .766 1.016 1.266 1.516 1.766 2.016 2.516 [6.75] [13.11] [19.46] [25.81] [32.16] [38.51] [44.86] [51.21] [63.91] Tube 5-104652-1 5-104652-2 5-104652-3 5-104652-4 5-104652-5 5-104652-6 5-104652-7 5-104652-8 6-104652-0 Receptacle Part Numbers Tape and Reel* No Hold Down w/Vacuum Cover 5-147384-1 5-147413-1 5-147384-2 5-147413-3 5-147384-3 5-147413-4 5-147384-4 -- 5-147384-5 5-147413-2 5-147384-6 -- 5-147384-7 -- 5-147384-8 -- 5-147384-9 -- * Parts packaged in tape and reel have vacuum pick and place cover. See PC Board Layout on page 22. Note: All part numbers are RoHS compliant. 20 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Board-to-Board Vertical Headers, Double Row, .050 x .050 [1.27 x 1.27] Centerline .050 [1.27] .225 [5.71] .050 [1.27] For .250 [6.35] Mated Height A .2255 [5.728] .030 [0.76] .050 [1.27] A For .320 [8.13] Mated Height .2975 [7.557] .050 [1.27] .030 [0.76] .050 [1.27] Vertical Headers, Double Row .030 [0.76] A .3675 [9.335] For .390 [9.91] Mated Height Material and Finish Related Product Data Technical Documents -- page 29 Housing--Glass-filled thermoplastic, black, 94V-0 rated Contacts--Copper alloy; duplex plated .000030 [0.00076] gold in mating area, .000150 [0.00381] tin on solder tail, with entire contact underplated .000050 [0.00127] nickel Holddown--Copper alloy; plated .000150 [0.00381] tin over .000050 [0.00127] nickel Mating Receptacles -- pages 20 and 26 (without latch only) PC Board Layouts -- page 22 Performance Specifications -- page 29 Product Specification 108-1332 Application Specification 114-7010 Packaging -- Tube or Tape and Reel No. of Pos. 10 20 30 40 50 60 70 80 90 100 Dimension A .372 .622 .872 1.122 1.372 1.622 1.872 2.122 2.372 2.622 [9.44] [15.79] [22.14] [28.49] [34.84] [41.19] [47.54] [53.89] [60.24] [66.59] .250 [6.35] Mated Height Tape & Reel* Tubes Hold Down No Hold Down 5-104655-1 5-147381-1 5-147121-1 5-104655-3 5-147381-2 5-147121-2 5-104655-4 5-147381-3 -- 5-104655-5 5-147381-4 -- 5-104655-6 5-147381-5 -- 5-104655-7 5-147381-6 -- 5-104655-8 5-147381-7 -- 5-104655-9 5-147381-8 -- -- -- -- 6-104655-1 5-147381-9 -- Header Part Numbers .320 [8.13] Mated Height Tubes Tape & Reel* 5-104656-1 5-104656-2 5-104656-3 5-104656-4 5-104656-5 5-104656-6 5-104656-7 5-104656-8 5-104656-9 6-104656-0 5-147382-1 5-147382-2 5-147382-3 5-147382-4 5-147382-5 5-147382-6 5-147382-7 5-147382-8 -- 5-147382-9 .390 [9.91] Mated Height Tubes Tape & Reel* Hold Down No Hold Down 5-104693-1 -- 5-147383-1 5-104693-2 -- 5-147383-2 5-104693-3 -- 5-147383-3 5-104693-4 -- 5-147383-4 5-104693-5 -- 5-147383-5 5-104693-6 -- 5-147383-6 5-104693-7 -- 5-147383-7 5-104693-8 -- 5-147383-8 5-104693-9 -- -- 6-104693-0 5-147503-1 5-147383-9 *Parts packaged in tape and reel have vacuum pick and place cover. See PC Board Layout on page 22. Note: All part numbers are RoHS compliant. 21 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Recommended PC Board Layouts for Vertical Connectors Headers .029 [0.74] .050 [1.27] B Spaces at .050 [1.27] = C .162 [4.11] .010 [0.25] 4 Plc. C L of Pattern Detail A .182 [4.62] .091 [2.31] .047 [1.19] 2 Plc. .061 [1.54] Detail A D Receptacles .029 [0.74] .050 [1.27] .110 [2.79] Recommended PC Board Layouts B Spaces at .050 [1.27] = C C L of Pattern .130 [3.30] .065 [1.65] Detail A .060 [1.52] D No. of Pos. B 10 20 30 40 50 60 70 80 90 100 4 9 14 19 24 29 34 39 44 49 Receptacle Dimensions C D .200 .450 .700 .950 1.200 1.450 1.700 1.950 2.200 2.450 [5.08] [11.43] [17.78] [24.13] [30.48] [36.83] [43.18] [49.53] [55.88] [62.23] .320 .570 .820 1.070 1.320 1.570 1.820 2.070 2.320 2.570 [8.12] [14.48] [20.83] [27.19] [33.53] [39.88] [46.23] [52.58] [58.93] [65.28] B 4 9 14 19 24 29 34 39 44 49 Header Dimensions C .200 .450 .700 .950 1.200 1.450 1.700 1.950 2.200 2.450 [5.08] [11.43] [17.78] [24.13] [30.48] [36.83] [43.18] [49.53] [55.88] [62.23] D .322 .572 .822 1.072 1.322 1.572 1.822 2.072 2.322 2.572 [8.17] [14.52] [20.87] [27.22] [33.57] [39.92] [46.27] [52.62] [58.97] [65.32] Note: Refer to Tyco Electronics Customer Drawings for additional PC board layout information and dimensional tolerances. 22 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Board-to-Board Right-Angle Headers Product Facts Surface-mount R R AMPMODU 50/50 Grid Right-Angle Headers will accommodate a variety of high density packaging applications; right-angle board-to-board applications when mated with vertical receptacles (page 20) and right-angle cable-to-board applications when mated with cable connectors (page 26). The small .050 x .050 [1.27 x 1.27] centerline contact spacing allows efficient use of the PC board area. Mechanical support of the headers to the PC board is provided by non-protrusive metallic holddowns designed for .062 [1.57] or thicker PC boards. These holddowns are of the same design as those used in the vertical headers (page 21) and receptacles (page 20). There are also metallic tabs that are soldered to the surfaces of the PC board pads for added support. Board-to-Board Right-Angle Headers products for right-angle board-to-board and cable-to-board applications Double-row, right-angle shrouded headers High density .050 x .050 [1.27 x 1.27] centerline grid Latching and non-latching versions available Non-protrusive metallic holddowns Metallic tabs, when soldered to PC board pad, provide added mechanical support Duplex plated post contacts; gold plated on mating area, tin plated on tails Compatible with standard surface-mount processing (VPR and IR) Standoffs on header housings allow for drainage of processing fluids All headers are polarized Sizes of 10, 20, 30, 40, 50, 60, 70, 80 and 100 positions Recognized under the Component Program of Underwriters Laboratories Inc., File No. E28476 Certified by Canadian Standards Association File No. LR7189 AMPMODU 50/50 Grid Right-Angle Headers are available in double-row, in either latching or nonlatching versions, and in sizes ranging from 10 through 100 positions (in 10 position increments). The latching version provides positive retention when mated with the latching cable connector (page 26). All headers feature polarization to help prevent misalignment during mating. 23 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Board-to-Board Right-Angle Headers, Double Row, .050 x .050 [1.27 x 1.27] Centerline Non-Latching Header A .050 [1.27] Typ. .050 [1.27] .213 [5.41] Latching Header .352 [8.94] .050 [1.27] .430 [10.92] .029 [0.74] Typ Material and Finish .065 [1.65] Typ. Right-Angle Headers, Double Row, Latching and Non-Latching Housing -- Liquid crystal polymer, black, 94V-0 rated Contacts -- Copper alloy; duplex plated .000030 [0.00076] gold in mating area, .000150 [0.000381] tin on solder tail, with entire contact underplated .000050 [0.00127] nickel Holddown -- Copper alloy; plated .0000150 [0.00381] tin over .000050 [0.00127] nickel .047 Dia [1.19] Plated-Thru Hole (2 Plc) B Spaces at .025 =C [0.64] .140 [3.56] .085 [2.16] .340 [8.64] .305 [7.75] .175 [4.45] .100 [2.54] Min Related Product Data Mating Receptacles -- pages 20 and 26 Performance Specifications -- page 29 .063 [1.57] (2 Plc) D .190 [4.83] (2 Plc) .136 [3.45] (2 Plc) Recommended PC Board Layout Note: Refer to Tyco Electronics Customer Drawings for additional PC board layout information and dimensional tolerances. Technical Documents -- page 29 Product Specification 108-1443 Application Specification 114-7010 Packaging -- Tube No. of Pos. 10 20 30 40 50 60 70 80 100 .630 .880 1.130 1.380 1.630 1.880 2.130 2.380 2.880 A B Dimensions C [16.00] [22.35] [28.70] [35.05] [41.40] [47.75] [54.10] [60.45] [73.15] 9 19 29 39 49 59 69 79 99 .225 .475 .725 .975 1.225 1.475 1.725 1.975 2.475 [5.72] [12.07] [18.42] [24.77] [31.12] [37.47] [43.82] [50.17] [62.87] D .550 .800 1.050 1.300 1.550 1.800 2.050 2.300 2.800 [13.97] [20.32] [26.67] [33.02] [39.37] [45.72] [52.07] [58.42] [71.12] Header Part Numbers Latching Non-Latching 5-104895-1 5-104894-1 5-104895-2 5-104894-2 5-104895-3 5-104894-3 5-104895-4 5-104894-4 5-104895-5 5-104894-5 5-104895-6 5-104894-6 5-104895-7 5-104894-7 5-104895-8 5-104894-8 6-104895-0 6-104894-0 Note: All part numbers are RoHS compliant. 24 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Cable-to-Board Connectors Product Facts Double-row R R These double-row cable connectors, with a .050 x .050 [1.27 x 1.27] centerline contact spacing, provide cable-to-board connection capabilities for the AMPMODU 50/50 Grid Connector System. Cable connectors without a latch will mate with the vertical headers (page 21), while cable connectors with or without a latch can be used to mate with the right-angle headers (page 24). The cable connectors feature reliable singlebeam IDC (insulation displacement crimp) contacts which are duplex plated with .000030 [0.00076] gold. These contacts can be mass terminated to either solid or stranded round conductor ribbon cable with conductor sizes of 28 AWG [0.08-0.09 mm2] and 30 AWG [0.05 mm2] and a maximum insulation diameter of .036 [0.91]. During termination, the terminating covers, which must be purchased separately, assist in guiding the wire into the IDC contacts, then provide strain relief when fully seated. Actual termination is accomplished with the Tyco Electronics manual tooling shown on page 28. mounted right-angle header. The cable connector without a metal latch features polarization to help prevent mismating. All connectors are available in sizes ranging from 10 through 100 positions (in 10 position increments). Cable-to-Board Connectors receptacle connectors provide cableto-board connection capabilities for vertical headers (non-latching) and right-angle headers (latching and non-latching) IDC (Insulation Displacement Crimp) mass termination of solid or stranded round conductor .050 [1.27] centerline ribbon cable with PVC or polyethylene insulation Accommodates ribbon cable conductor sizes of 28 AWG [0.08-0.09 mm2] and 30 AWG [0.05 mm2] and insulation diameters up to .036 [0.91] maximum Reliable single beam receptacle contact design Duplex plated receptacle contacts; gold plated in mating area, tin in termination area Terminating covers (sold separately) provide both strain relief and protection to the termination area Sizes of 10, 20, 30, 40, 50, 60, 70, 80 and 100 positions Connectors available with or without metal latch Connectors without latches are polarized to help prevent mismating Recognized under the Component Program of Underwriters Laboratories Inc., File No. E28476 Certified by Canadian Standards Association File No. LR7189 The latching version of the cable connector is equipped with a metal latch which provides positive retention of the receptacle cable connector when mated with a surface- 25 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Cable-to-Board Receptacle Connectors, Double Row, .050 x .050 [1.27 x 1.27] Centerline A Material and Finish Housing -- Thermoplastic, black, 94V-0 rated Latch -- Stainless steel Contacts -- Phosphor bronze; duplex plated .000030 [0.00076] minimum gold in mating area, .000150 [0.00381] minimum tin on solder tail, with entire contact underplated .000050 [0.00127] minimum nickel .280 [7.11] .627 [15.94] .690 [17.56] Related Product Data Mating Headers -- pages 21 and 24 (latching) Terminating Covers (Must be Purchased Separately, 2 Required per Connector) -- page 27 Termination Tooling -- page 28 Performance Specifications -- page 29 D .120 [3.05] .050 [1.27] Typ B Spaces at .050 [1.27] = C Technical Documents -- page 29 Receptacle Connectors, Double Row, With and Without Latch Product Specification 108-1443 Application Specification 408-9817, 408-9909 Packaging -- Tube .284 .327 [7.21] [8.31] .050 [1.27] No. of Pos. 10 20 30 40 50 60 70 80 100 .578 .828 1.078 1.328 1.578 1.828 2.078 2.328 2.828 A B Dimensions C [14.68] [21.03] [27.38] [33.73] [40.08] [46.43] [52.78] [59.13] [71.83] 4 9 14 19 24 29 34 39 49 .200 .450 .700 .950 1.200 1.450 1.700 1.950 2.450 [5.08] [11.43] [17.78] [24.13] [30.48] [36.83] [43.18] [49.53] [62.23] D .266 .516 .766 1.016 1.266 1.516 1.766 2.016 2.516 [6.76] [13.11] [19.46] [25.81] [32.16] [38.51] [44.86] [51.21] [63.91] Receptacle Part Numbers With Latch Without Latch 5-104892-1 5-104893-1 5-104892-2 5-104893-2 5-104892-3 5-104893-3 5-104892-4 5-104893-4 5-104892-5 5-104893-5 5-104892-6 5-104893-6 5-104892-7 5-104893-7 5-104892-8 5-104893-8 6-104892-0 6-104893-0 Note: All part numbers are RoHS compliant. 26 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Terminating Covers for Cable Connectors Material Glass-filled thermoplastic, black, 94V-0 rated A .191 [4.85] Related Product Data Connectors used with Covers -- page 26 Termination Tooling -- page 28 Technical Documents -- page 29 .277 [7.04] Product Specification 108-1443 Application Specification 408-9817, 408-9909 Packaging -- Plastic bag Cable Conncetor Terminating Cover, Double Row No. of Dimension Terminator Cover Pos. A Part Numbers 10 .565 [14.35] 104891-1 20 .815 [20.70] 104891-2 30 1.065 [27.05] 104891-3 40 1.315 [33.82] 104891-4 50 1.565 [39.75] 104891-5 60 1.815 [46.10] 104891-6 70 2.065 [52.45] 104891-7 80 2.315 [58.80] 104891-8 100 2.815 [71.50] 1-104891-0 Note: Terminating covers must be purchased separately, two are required for each cable connector. Note: All part numbers are RoHS compliant. 27 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Application Tooling for Cable Connectors The Manual Miniature Application Frame Assembly 91295-1, equipped with a Cover Closing Kit 543518-1, is used for the IDC termination of ribbon cable to the cable connectors shown on page 26. Prior to termination, the covers must be partially assembled onto a connector housing, the cable inserted between the covers and contacts and the covers preclosed by hand, clamping the cable in place. In the Manual Miniature Application Frame Assembly, the covers are fully seated to complete the mass termination and provide strain relief for the completed connection. Manual Miniature Application Frame Assembly 91295-1 with Cover Closing Kit 543518-1 For tooling information, call Technical Support Center 1-800-522-6752. IDC (Insulation Displacement Crimp) Tooling Note: Refer to Tyco Electonics Instruction Sheets 408-9817 (frame assembly 91295-1) and 408-9909 (cover closing kit 543518-1) for complete termination/tooling information. Note: All part numbers are RoHS compliant. 28 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Performance Specifications Board-to-Board Connectors, Vertical and Right-Angle Mating Force -- 6.4 oz (1.78 N] max. per contact Unmating Force -- 1.0 oz [0.28 N] min. per contact Durability -- Tested to 200 cycles min. Current Rating -- (30C T rise): .5 ampere per contact Operating Temperature Range -- -65C to +105C Termination Resistance -- 16 milliohms max. (initial) Insulation Resistance -- 5000 megohms min. (initial) Dielectric Withstanding Voltage -- 300 VAC Cable-to-Board Connectors Mating Force -- 6.4 oz (1.78 N] max. per contact Unmating Force Without Latch -- .5 oz [0.14 N] min. per contact Durability -- Tested to 200 cycles min. Current Rating -- (10C T rise); .5 ampere per contact Operating Temperature Range -- -65C to +105C Termination Resistance -- 25 milliohms max. (initial and final) Insulation Resistance -- 5000 megohms min. (initial) Dielectric Withstanding Voltage -- 300 VAC Technical Documents Various technical documents are available for your use: Product Specifications describe technical performance characteristics and verification tests. They are intended for the Design, Component and Quality Engineer. 108-1332 AMPMODU 50/50 Grid Vertical Board-to-Board Connectors 108-1443 AMPMODU 50/50 Grid Right-Angle Board-to-Board and Cable Connectors Application Specifications describe requirements for using the product in its intended application and/or crimping information. They are intended for the Packaging and Design Engineer and the Machine Setup Person. 114-7010 AMPMODU 50/50 Grid Connector System Instruction Sheets provide instructions for assembling or applying the product. They are intended for the Manufacturing Assembler or Operator. Manual Miniature Application Frame Assembly 91295-1 Cover Closing Kit 543518-1 Performance Specifications/ Technical Documents 408-9817 408-9909 Note: All part numbers are RoHS compliant. 29 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Micro-MaTch Miniature Connector System Features/ Benefits Micro-MaTch Miniature Connector System I I I I I I I Available in 2 to 20 positions Applicable Wire: 20~28 AWG Wire connectors supplied on-tape and suitable for mass termination of 28 AWG [0.08 mm2 to 0.09 mm2] ribbon cable Tin plated contact design Guaranteed minimum contact force of 2.0 N Fretting corrosion proof thanks to additional positioning spring member Full range of application tooling from hand tool to fully automated equipment 1 2 3 1. Contact Pin 2. Contact Spring 3. Positioning Miniaturization and the trend towards higher density of electronic functions on a substrate led to the introduction of smaller interconnection systems. The Micro-MaTch connector family, with it's contact spacing of 1.27 mm, fully complies with the electronic packaging requirements of today and the future. The system offers a range of board and wire connectors, enabling a variety of wireto-board and board-toboard interconnections. The Micro-MaTch contact shown on this page is essentially different from other systems available. By its design the traditional failure mode in tin plated connections, fretting corrosion, is prevented. Due to an additional positioning spring in the female part, relative movements caused by vibrations/thermal expansion between male and female contacts are absorbed. By preventing movements on the contact spot, a gas tight connection can be guaranteed under all circumstances. The contact spring is located in the board connector and not in the cable connector, which is usually the case. The counter part, incorporated in the cable connector, is a simple pin, either with an insulation displacement section, suitable for the mass-termination of cable or with a kinked solder leg to be soldered onto a PC Board. The separation of these two basic functions of the contact system -- contact force generation and wire termination -- enables the independent optimization of both functions and also leads to relatively simple contact shapes. Because of their shapes contacts can be postplated, leaving no bare edges in the contact and wire slot area. The contact spring system features an additional spring member -- the positioning spring -- which compensates positional tolerances. In this way the contact spring can be fully optimized for its basic function, so that the relatively high contact force, required for tin plated contact systems, can be guaranteed under all circumstances. The Micro-MaTch contact spring system is absolutely fretting corrosion proof by its design. 30 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Micro-MaTch Miniature Connector System Overview Technical Data Technical Data 1.27 mm (staggered) 4, 6, 8, 10, 12, 14, 16, 18, 20, and some 24 positions Phosphor bronze Tin over Nickel Thermoplastic polyester, red, glass-filled For surface mount versions polyamide 4.6 Flammability rating: per UL 94 V-0 UL-recognized: File E28476 Vol. 23 Section 4 Contact Resistance: 10 M max. Insulation Resistance: 1.000 M min. Nominal Voltage: 230 V Current Rating: 1.5 A max. Temperature Range: -40 C to +105 C (operating) Mating Force: 5N max. per contact Unmating Force: 1N min. per contact Minimum Contact Force: 2N min. Product Specification: 108-19052 Application Specification: 114-19016, 114-19051 RoHS Compliance Code: Always RoHS compliant (directive 2002/95/EC) for all types Lead-free Process Capable: Wave solder capable to 265 C for through hole versions reflow solder capable to 260 C for SMD versions Micro-MaTch Miniature Connector System Overview Technical Data Centerline: Number of Positions: Contact Material: Contact Finish: Housing Material: PC Board Connectors PC Board Thickness: PC Board Hole Diameter: 1.6 mm nominal 0.8 mm for solder connectors Ribbon Connectors Cable Type: Conductor Spacing: Conductor Diameter: Insulation Type: Insulation Diameter: Ribbon cable, UL Style 2651 1.27 mm (.050") Solid 0.30 mm diameter Stranded 0.08 mm2 7 x 0.12 - 0.13 mm (other diameters and/or configurations on request) semi-rigid PVC 0.9 0.1 mm Discrete Wire (COSI) Connectors Cable Type : AWG 28-24 and 24-20 31 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Micro-MaTch Miniature Connector System Applications (3 Dimensions) Micro-MaTch Miniature Connector System Applications (3 Dimensions) Male Connectors Female Connectors Male-on-Wire Part Number 215083 Male-on-Board Part Number 215464 COSI Part Number 338095 Part Number 338096 Part Number 338097 1 2 3 4 5/6 7 8 9 10 Paddle Board Part Number 215570 Female Top Entry Part Number 215079 Female Side Entry Part Number 215460 SMD Top Entry Part Number 188275 Image 1 2 3 4 5 6 7 8 9 10 Description (see also page 33) Wire-to-Board through hole Board-to-Board through hole Wire-to-Board (discrete wire), through hole Wire-to-Board right angle, through hole Board-to-Board right angle, through hole Board-to-Board right angle, through hole Wire-to-Board right angle (discrete wire), through hole Wire-to-Board surface mount Board-to-Board surface mount, through hole Wire-to-Board (discrete wire), surface mount 32 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Micro-MaTch Miniature Connector System Applications (2 Dimensions) Male Connectors Male-on-Board Part Number 215464 Male-on-Wire Part Number 215083 Female Connectors 2 3 A C A A B B B Female Top Entry Part Number 215079 C C C 6 4 A 7 5 A C B C B G E D Female Side Entry Part Number 215460 E A B AB C F C Paddle Board Part Number 215570 Micro-MaTch Miniature Connector System Applications (2 Dimensions) 1 COSI Part Number 338095 Part Number 338096 Part Number 338097 D C C D 8 9 A A 10 A C B B B SMD Top Entry Part Number 188275 Image 1 2 3 4 5 6 7 8 9 10 A (max) 5.2 5.2 5.2 8.4 5.2 5.2 5.2 5.2 5.2 5.2 D D B (max) 7.5 6.2 9.7 5.9 5.9 5.9 5.9 8.5 7.1 10.7 C 2.54 2.54 2.54 2.54 2.54 2.54 2.54 -- 2.54 -- D Dimensions (mm) D (max) -- -- -- 1.5 1.5 1.5 1.5 7.1 7.1 7.1 E (max) -- -- -- -- 7.0 -- 10.6 -- -- -- F(max) -- -- -- -- 1.6 -- -- -- -- -- G (max) -- -- -- -- -- 2.8 -- -- -- -- 33 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 METRIC Dimensions are millimeters over inches Ribbon Cable Interconnect Solutions Micro-MaTch Miniature Connector System -- Female-on-Board Connector, Top Entry 1.5 [.059] 5.1 Max. [.200] Micro-MaTch Miniature Connector System -- Female-on-Board Connector, Top Entry This connector version incorporates the MicroMaTch contact spring system and is designed to be soldered onto PC Boards with a nominal thickness of 1.6 mm. The solder legs are indented, providing firm retention of the connector before and during the soldering operations. 4.0 [.157] 1.9 [.074] 3.1 [.122] 1.27 [.050] A B Max. As polarization is accomplished directly between the Micro-MaTch male connectors and the PC Board, this top entry female connector does not have any polarizing features. Therefore, the orientation of the connector on the PC Board is irrelevant. 1.40 [.055] 2.54 [.100] 0.80 [.031] 1.27 [.050] 1.80 [.071] 1.50 Hole for [.059] Polarization Pin 2.54 [.100] Typical Hole Pattern Not Solder Side Shown Notes: 1. Connectors are always sideways mounted onto an adhesive tape. 2. Standard packaging quantity is 2500 connectors on a reel with a diameter of 600 mm. 3. At additional charge a special packaging option is available: 250 connectors on a reel with a diameter of 250 mm, packed in a dedicated dispenser box. Mates with: X-338095-X X-215083-X X-215464-X X-338728-X No. of Positions 4 6 8 10 12 14 16 18 20 Dimensions A 3.81 6.35 8.89 11.43 13.97 16.51 19.05 21.59 24.13 (mm) B 7.1 9.7 12.2 14.7 17.3 19.8 22.4 24.9 27.4 Part Numbers 2500 Connectors/Reel 250 215079-4 215079-6 215079-8 1-215079-0 1-215079-2 1-215079-4 1-215079-6 1-215079-8 2-215079-0 Connectors/Box 7-215079-4 7-215079-6 7-215079-8 8-215079-0 8-215079-2 8-215079-4 8-215079-6 8-215079-8 9-215079-0 34 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 METRIC Dimensions are millimeters over inches Ribbon Cable Interconnect Solutions Micro-MaTch Miniature Connector System -- Female-on-Board Connector, Side Entry B Max. 3.1 [0.12] 5.8 [0.23] This connector version is identical to the top entry version with two exceptions: I It's housing is polarized, so that polarization is accomplished directly between the two mating connectors. Proper orientation of the connectors on the PC Board is relevant here. 2.54 [0.09] 5.3 Max. [0.21] Micro-MaTch Miniature Connector System -- Female-on-Board Connector, Side Entry I 3.85 [0.15] The solder legs are parallel to the mating face of the connector instead of perpendicular. 0.90 [.039] 1.27 [.050] 2.54 [.100] A 2.54 [0.09] 1.27 [0.05] 2.54 [0.09] 0.80 Nom. [0.03] (N-1)x1.27 Recommended PCB Hole Layout Not Solder Side Shown Notes: 1. Connectors are always sideways mounted onto an adhesive tape. 2. Standard packaging quantity is 2500 connectors on a reel with a diameter of 600 mm. 3. At additional charge a special packaging option is available: 250 connectors on a reel with a diameter of 250 mm, packed in a dedicated dispenser box. Mates with: X-338095-X X-215083-X X-215464-X X-338728-X No. of Positions 4 6 8 10 12 14 16 18 20 Dimensions A 3.81 6.35 8.89 11.43 13.97 16.51 19.05 21.59 24.13 (mm) B 7.1 9.7 12.2 14.7 17.3 19.8 22.4 24.9 27.4 Part Numbers 2500 Connectors/Reel 250 (1500) 215460-4 (1500) 215460-6 215460-8 1-215460-0 1-215460-2 1-215460-4 1-215460-6 1-215460-8 2-215460-0 Connectors/Box 7-215460-4 7-215460-6 7-215460-8 8-215460-0 8-215460-2 8-215460-4 8-215460-6 8-215460-8 9-215460-0 35 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 METRIC Dimensions are millimeters over inches Ribbon Cable Interconnect Solutions Micro-MaTch Miniature Connector System -- Female-on-Board Connector Surface Mount Device (SMD) Tape for Vacuum P&P Micro-MaTch Miniature Connector System -- Female-on-Board Connector Surface Mount Device (SMD) 1.90 [.075] 1.27 [.050] This SMD connector version is designed for standard reflow and infrared solder processes ("FULL SMD"). Polarization is accomplished by the housing, therefor no polarization holes in the PC Board are required. A=(N-1)*1.27 0.5B-2.5 5.0 [.197] 5.0 [.197] The contact is designed with an additional spring to compensate for differences in thermal expansion between housing and PCB. Due to this feature, tension on solder joints is prevented. 7.0 [.276] B A 2.54 [.100] 5.0 [.197] 1.50 [.059] 3.00 Minimum [.118] Solder Path Length 1.50 [.059] Recommended PCB Layout Top View Notes: 1. To enable automatic pick & placement, connectors are always packed in embossed tape according EIA481 specification. 2. Standard packaging quantity is 900 pcs on a reel with a diameter of 330 mm. 3. Connectors are supplied with or without a feature for vacuum Pick & Placement. 4. For this connector no additional solder hold down is required. Mates with: X-338095-X X-215083-X X-215464-X X-338728-X No. of Positions 4 6 8 10 12 14 16 18 20 Dimensions A 3.81 6.35 8.89 11.43 13.97 16.51 19.05 21.59 24.13 (mm) B 7.1 9.7 12.2 14.7 17.3 19.8 22.4 24.9 27.4 Part Numbers 2500 Connectors/Reel 250 188275-4 188275-6 188275-8 1-188275-0 1-188275-2 1-188275-4 1-188275-6 1-188275-8 2-188275-0 Connectors/Box 7-188275-4 7-188275-6 7-188275-8 8-188275-0 8-188275-2 8-188275-4 8-188275-6 8-188275-8 9-188275-0 36 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 METRIC Dimensions are millimeters over inches Ribbon Cable Interconnect Solutions Micro-MaTch Miniature Connector System -- Male-on-Board Connector A 5.00 [.197] A This male connector version is designed to be soldered onto PC Boards with a nominal thickness of 1.6 mm. A 2.54 [.100] The solder legs are indented for firm retention of the connector in the PC Board. B 1.27 [.050] 6.75 [.266] The connector housing features a polarizing pin on one end for proper orientation of this connector version. 7.10 [.280] Micro-MaTch Miniature Connector System -- Male-on-Board Connector Section A-A 0.80 [.031] 2.54 [.100] 1.27 [.050] 2.54 [.100] Typical Hole Pattern Not Solder Side Shown Notes: 1. To enable automatic pick & placement, connectors are always packed in embossed tape according EIA481 specification. 2. Standard packaging quantity is 900 pcs on a reel with a diameter of 330 mm. 3. Connectors are supplied with or without a feature for vacuum pick & placement. 4. For this connector no additional solder hold down is required. Mates with: X-338095-X X-215083-X X-215464-X X-338728-X No. of Positions 4 6 8 10 12 14 16 18 20 Dimensions A 3.81 6.35 8.89 11.43 13.97 16.51 19.05 21.59 24.13 (mm) B 8.2 10.7 13.3 15.8 18.3 20.8 23.4 25.9 28.4 Part Numbers 2500 Connectors/Reel 250 215464-4 215464-6 215464-8 1-215464-0 1-215464-2 1-215464-4 1-215464-6 1-215464-8 2-215464-0 Connectors/Box 7-215464-4 7-215464-6 7-215464-8 8-215464-0 8-215464-2 8-215464-4 8-215464-6 8-215464-8 9-215464-0 37 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 METRIC Dimensions are millimeters over inches Ribbon Cable Interconnect Solutions Micro-MaTch Miniature Connector System -- Male-on-Wire Connector A A For the wire connection, a well-known type blade with a single slot is used. The insides of the slots are tin plated for stable and reliable connections. A Max. B Max. 5.10 Max. [.201] Micro-MaTch Miniature Connector System -- Male-on-Wire Connector 6.8 The connector is supplied with a pre-assembled cover, providing excellent positioning of the ribbon cable before and during the insulation displacement process. C 10.20 [.402] After termination the cover is held in place by each individual contact in addition to two plastic latches at both ends of the connector. Section A-A Remark: The Micro-MaTch male-on-wire connector is specifically designed to be disengaged from its counterpart by pulling the cable in the appropriate direction. Notes: 1. Connectors are always sideways mounted onto an adhesive tape. 2. Standard packaging quantity is 2500 connectors on a reel with a diameter of 600 mm. 3. At additional charge a special packaging option is available: 250 diameter of 250 mm, packed in a dedicated dispenser box. Mates with: X-215460-X X-188275-X X-215079-X X-338068-X X-338069-X X-338070-X X-100411-X X-188431-X No. of Positions 4 6 8 10 12 14 16 18 20 24 Dimensions (mm) A B C 8.6 5.4 3.81 11.1 8.0 6.35 3.6 10.5 8.89 16.2 13.0 11.43 18.7 15.6 13.97 21.3 18.1 16.51 23.8 20.7 19.05 26.3 23.2 21.59 28.9 25.7 24.13 34.0 30.8 29.21 Part Numbers 2500 Connectors/Reel 250 215083-4 215083-6 215083-8 1-215083-0 1-215083-2 1-215083-4 1-215083-6 1-215083-8 2-215083-0 2-215083-4 Connectors/Box 7-215083-4 7-215083-6 7-215083-8 8-215083-0 8-215083-2 8-215083-4 8-215083-6 8-215083-8 9-215083-0 9-215083-4 38 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 METRIC Dimensions are millimeters over inches Ribbon Cable Interconnect Solutions Micro-MaTch Miniature Connector System -- Paddle Board Connector A 5.00 [.197] A Direct soldering of a ribbon cable onto a PC Board is a very difficult job with the smaller sizes of ribbon cable. If such a permanent cable connection is required, the application can be facilitated by using this connector type. A 2.54 [.100] B 1.27 [.050] 6.75 [.266] The Paddle Board connector is applied to the ribbon cable with the same application tooling, available for the termination of the Male-on-Wire connector. 7.10 [.280] Section A-A The solder legs are indented and provide mechanical retention of the connector/cable assembly in the PC Board before and during soldering. This Paddle Board connector version is designed to be soldered onto PC Boards with a nominal thickness of 1.6 mm. 2.54 [.100] Micro-MaTch Miniature Connector System -- Paddle Board Connector 0.80 [.031] 1.27 [.050] 2.54 [.100] Typical Hole Pattern Not Solder Side Shown Notes: 1. To enable automatic pick & placement, connectors are always packed in embossed tape according EIA481 specification. 2. Standard packaging quantity is 900 pcs on a reel with a diameter of 330 mm. 3. Connectors are supplied with or without a feature for vacuum pick & placement. 4. For this connector no additional solder hold down is required. No mate -- direct soldering of ribbon cable onto the PC Board No. of Positions 4 6 8 10 12 14 16 18 20 24 Dimensions (mm) A B C 8.6 5.4 3.81 11.1 8.0 6.35 3.6 10.5 8.89 16.2 13.0 11.43 18.7 15.6 13.97 21.3 18.1 16.51 23.8 20.7 19.05 26.3 23.2 21.59 28.9 25.7 24.13 34.0 30.8 29.21 Part Numbers 2500 Connectors/Reel 250 215570-4 215570-6 215570-8 1-215570-0 1-215570-2 1-215570-4 1-215570-6 1-215570-8 2-215570-0 2-215570-4 Connectors/Box 7-215570-4 7-215570-6 7-215570-8 8-215570-0 8-215570-2 8-215570-4 8-215570-6 8-215570-8 9-215570-0 -- 39 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 METRIC Dimensions are millimeters over inches Ribbon Cable Interconnect Solutions Micro-MaTch Miniature Connector System -- Crimp On Snap In (COSI) Connector C 2.54 [.100] 1.27 [.050] 2.65 [.104] Basic Part Number 338095 and Contacts Part Numbers 338096 and 338097 B Max. 5.10 Max. [.201] This crimp version for discrete Wire-to-Board applications is fully compatible with all female connectors of the Micro-MaTch family. Micro-MaTch Miniature Connector System -- Crimp On Snap In (COSI) Connector Insulation and wire crimp barrel are copies of the well proven AMPLIMITE contacts. After mating with a Micro-MaTch female connector the contacts are fully protected by isolating plastics. Contacts are made of a pre-tinned phosphor bronze. A Max. 9.10 Max. [.358] 0.82 [.032] 12.40 Max. [.488] 0.70 [.027] 6.00 Ref. [.236] Contacts are supplied in a range for 24-20 AWG and 28-24 AWG. For repair operations an extraction tool is available; Part Number 734873-1. 0.40 [.016] 0.20 [.008] 0.25 Cut Off [.010] Max. 8.65 Max. [.341] Notes: 1. Contacts can be crimped using a mini stripper crimper based applicator. 2. For the contacts on strip the standard packaging quantity is 15.000 pcs on a reel with a diameter of 600 mm. 3. For repair/service contacts are packaged 750 pcs. Per reel, to be used with handtools. 4. The housings are bulk packed in a box with a packaging quantity varying from 200 to 900 pcs per box. Mates with: X-338095-X Mates with: X-215460-X X-188275-X X-215079-X X-338068-X X-338069-X X-338670-X X-100411-X X-188431-X Wire Size Range (mm2) (AWG) 0.08-0.20 28-24 0.20-0.50 24-20 No. of Positions 4 6 8 10 12 14 16 18 20 Insulation Diameter (mm) 0.76-1.00 1.27-1.52 Dimensions (mm) A B C 7.2 8.4 3.81 9.8 10.9 6.35 12.3 13.5 8.89 14.9 16.0 11.43 17.4 18.5 13.97 19.9 21.1 16.51 22.5 23.6 19.05 25.0 26.2 21.59 27.6 28.7 24.13 Part Number Large reel, 15.000 Small reel, 750 338096-1 1-338096-1 338097-1 1-338097-1 Part Numbers 2500 Connectors/Reel 250 Connectors/Box 338095-4 900 338095-6 700 338095-8 500 1-338095-0 450 1-338095-2 400 1-338095-4 350 1-338095-6 300 1-338095-8 250 2-338095-0 200 40 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Micro-MaTch Miniature Connector System -- Specials SMC Connector Part Number 100411 This connector type enables a solderless application to the printed circuit board. Contact is made on the surface of the PCB, enabling the use of paperphenol and epoxy boards with both drilled and punched holes. This connector is suitable for both wire-to-board as board-to-board connections. Because this connector is mounted on the solder side, the components of both PCB's in a parallel Board-to-Board application, will be in the same direction. By this, the stacking of two or more PCB's is possible. Application tooling available on request. Mates with: X-215464-X X-338095-X X-215083-X Locking Latch Part Numbers 338068/338069/338070 For wire-to-board applications this feature provides an audible click during mating. This feature is available for the standard Micro-MaTch female connectors. Cross reference is made by base part number x-338068-x instead of x-215079-x, x-338069-x instead of x-188275-x and x-338070-x instead of x-215460-x (standard large reel packaging only). Mates with: X-338095-X X-215464-X X-338728-X X-215083-X Micro-MaTch Miniature Connector System -- Specials In-board SMD Part Number 188431 This connector is only tooled in 20 position (9-188431-0) and packaged in embossed tape according to EIA481 standards. The connectors are equipped with a feature for vacuum pick & placement. It enables the mounting of a PCB with the solder side direct behind e.g. a display. It is also possible to obtain a parallel BTB application with an extreme low PCB distance of 4.2 mm. Mates with: X-338095-X X-215464-X X-338728-X X-215083-X Male SMD Part Number 338728 This connector enables the possibility to have a full SMD to SMD board-to-board application. It mates with all Micro-MaTch female connectors, and will be packaged according EIA 481 standard. Consult Tyco Electronics for more information. Mates with: X-215079-X X-215460-X X-188275-X X-338069-X X-338070-X X-188431-X X-338068-X 41 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Micro-MaTch Miniature Connector System Application Tooling Micro-MaTch Miniature Connector System Application Tooling Pistol Handgrip Tooling. This is a handtool for terminating Micro-MaTch Male-on-Wire and Paddle Board connectors. Meant for small quantities or repair services. Pistol handgrip and adapter must be ordered separately. Standard Pistol Handgrip Part Number 734155-1. This basic tool can be used for Micro-MaTch and other applications. Pistol Handgrip Adapter Set Part Number 734024-1. This adapter can be used for Micro-MaTch terminations, together with the pistol handgrip. Bench Press Tooling Part Number 733280-3. This complete tool includes a Micro-MaTch dedicated tool set mounted on the bench press 654173-2. Bench Press Part Number 91085-2. This basic press is a hand operated version. This press can also be obtained in a pneumatically operated version; Part Number 91112-3. Bench Press Tool Set Part Number 733278-2. This tool set is designed especially for Micro-MaTch. It fits both pneumatically and hand operated press. COSI Hand Tooling Part Number 734870-1 for 24-20 AWG, and Part Number 734870-2 for 28-24 AWG. These dedicated tools can be obtained for services/repair applications. AMP-O-LECTRIC G-terminator Model Applicators for AMP-O-LECTRIC Part Number 677499-1. G-terminator. Part Number 677894-1 for AWG 28-24 (Part Number 3380961) and Part Number 677895-1 for AWG 24-20 (Part Number 338097-1). 42 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Micro-MaTch Miniature Connector System Application Tooling (Continued) Semiautomatic Tooling Part Number 677410-1. This tool can be used for Micro-MaTch connector lead end and for daisy chain assembly applications. Semiautomatic Tooling Part Number 677412-5 for Micro-MaTch connectors only and Part Number 1-677412-0 for both Micro-MaTch and other ribbon cables. This machine can be used for lead end assemblies. Micro-MaTch Miniature Connector System Application Tooling Connector Dispenser Part Number 677463-1. The dispenser accepts the Micro-MaTch standard connectors reels (2500 pcs/reel). It automatically removes the preset connector quantity from the reel and drops it in a separate box. Quantity can easily be programmed by the user. 43 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Micro-MaTch Miniature Connector System Lead Assembly It is possible to deliver custom made Micro-MaTch connector lead assemblies, both cable end assemblies and daisy-chain assemblies, in all positions between 4 and 20 in all required cable lengths. All leads are 100% electrically tested on shortcut and connection before shipment. A flexible 7 stranded cable is used for easy assembly. Special cable on request. For order information contact Tyco Electronics. Micro-MaTch Miniature Connector System Sample Box Sample Box Part Number 1377074-1 Micro-MaTch Miniature Connector System Lead Assembly and Sample Box This box includes samples of all connector types within the Micro-MaTch connector family, examples of leads, printed circuit boards and a CD-ROM. The CD-ROM includes an electronic version of this catalogue, an animation of the contact principle and CAD files of all connector types. This sample box is an aid in visualizing the variety of applications where Micro-MaTch connector can be implemented. 44 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions PageHead_12_HelvCdBd Universal I/O Pin Connectors (Continued) without Mounting Ears Material and Finish Housing and Cover -- Flame retardant UL 94V-0 rated thermoplastic, black Contacts -- Phosphor bronze, .000100 [0.00254] min. tin on termination end, .000030 [0.00762] min. gold on mating end, both over .000050 [0.00127] min. nickel Without Latches With Latches Technical Documents Product Specification 108-1336 Application Specification 114-7011 Instruction Sheets 408-9720 408-6939 I I Recognized under the Component Program of the Underwriters Laboratories, Inc. UL File No. E28476 B 0.754 .015 [19.15 0.36] R Certified by the Canadian Standards Association, File No. LR 7189 A Pin Length .240 [6.10] R .330 [8.38] Accessories Strain Relief -- page 67 Ejector Latch -- page 63 Military Polarizer -- page 63 Terminates 26 and 28 AWG solid or stranded ribbon cable. See Application Specification for cable requirements. Position No.1 Indicator No. of Positions 103,4 Related Product Data 16 20 24 26 30 34 40 44 50 60 64 1 2 Note: All part numbers are RoHS compliant. 3 4 Part Numbers of Connectors with: No Latches Short Latches1 Long Latches2 1-111446-4 1-111492-5 1-111504-4 1-111446-5 1-111492-6 1-111504-5 1-111446-6 1-111492-7 1-111504-6 1-111446-8 -- 1-111504-7 1-111446-9 1-111492-9 1-111504-8 2-111446-0 2-111492-0 -- 2-111446-1 2-111492-1 2-111504-0 2-111446-2 2-111492-2 -- 2-111446-3 2-111492-3 -- 2-111446-4 2-111492-4 2-111504-3 1-111446-7 2-111492-5 -- 2-111446-5 2-111492-6 -- 2-111446-6 -- 2-111504-6 .050 [1.27] Centerline Ribbon Cable Connectors Universal I/O Pin Connectors without Mounting Ears 143,4 Mateable Receptacles Novo -- pages 48-51 Female Socket Connectors -- pages 52-55 Dimensions A B .992 1.072 25.20 27.23 1.192 1.272 30.28 32.31 1.292 1.372 32.82 34.85 1.492 1.572 37.90 39.93 1.692 1.772 42.98 45.01 1.792 1.872 45.52 47.55 1.992 2.072 50.60 52.63 2.192 2.272 55.68 57.71 2.492 2.572 63.30 65.33 2.692 2.772 68.38 70.41 2.992 3.072 76.00 78.03 3.492 3.572 88.70 90.73 3.692 3.772 93.78 95.81 Pins On Centerlines .100 [2.54] Use short latch versions when mating connectors without strain reliefs are used. Use long latch versions when mating connectors with strain reliefs are used. No slot on end with position No. 1 indicator for 10 and 14-position connectors. No slot for snap-in polarizer on end with position No. 1 indicator for 10 and 14-position connectors. 45 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Universal I/O Pin Connectors with Slotted Mounting Ears Material and Finish Housing and Cover -- Flame retardant UL 94V-0 rated thermoplastic, black Contacts -- Phosphor bronze, .000100 [0.00254] min. tin on termination end, .000030 [0.00762] min. gold on mating end, both over .000050 [0.00127] min. nickel Without Latches With Latches Technical Documents Product Specification 108-1336 Application Specification 114-7011 Instruction Sheets 408-9720 408-6939 I I Recognized under the Component Program of the Underwriters Laboratories, Inc. UL File No. E28476 B .754 .015 [19.15 0.36] R A Certified by the Canadian Standards Association, File No. LR 7189 Pin Length .240 [6.10] R .330 [8.38] Accessories Ejector Latch -- page 63 Military Polarizer -- page 63 Terminates 26 and 28 AWG solid or stranded ribbon cable. See Application Specification for cable requirements. Position No.1 Indicator No. of Positions 103,4 Related Product Data .050 [1.27] Centerline Ribbon Cable Connectors Universal I/O Pin Connectors with Slotted Mounting Ears Mateable Receptacles Novo -- pages 48-51 Female Socket Connectors -- pages 52-55 143,4 16 20 24 26 30 34 40 44 50 60 64 1 2 Note: All part numbers are RoHS compliant. 3 4 Dimensions A B .992 1.476 25.20 37.49 1.192 1.676 30.28 42.57 1.292 1.776 32.82 45.11 1.492 1.976 37.90 50.19 1.692 2.176 42.98 55.27 1.792 2.276 45.52 57.81 1.992 2.476 50.60 62.89 2.192 2.676 55.68 67.97 2.492 2.976 63.30 75.59 2.692 3.176 68.38 80.67 2.992 3.476 76.00 88.29 3.492 3.976 88.70 100.99 3.692 4.176 93.78 106.07 Pins On Centerlines .100 [2.54] Part Numbers of Connectors with: No Latches Short Latches1 Long Latches2 5111448-1 1-111494-5 1-111506-6 -- -- -- 5111448-3 -- 1-111506-8 5111448-4 1-111494-8 -- 5111448-5 1-111494-9 2-111506-0 -- -- 2-111506-1 5111448-7 2-111494-0 -- 5111448-8 2-111494-1 -- 5111448-9 2-111494-2 2-111506-4 -- 2-111494-3 2-111506-5 -- 2-111494-4 1-111506-4 -- 2-111494-5 -- 1-5111448-3 2-111494-6 -- Use short latch versions when mating connectors without strain reliefs are used. Use long latch versions when mating connectors with strain reliefs are used. No slot on end with position No. 1 indicator for 10 and 14-position connectors. No slot for snap-in polarizer on end with position No. 1 indicator for 10 and 14-position connectors. 46 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 METRIC Dimensions are millimeters over inches Ribbon Cable Interconnect Solutions EUROLATCH Receptacles, 64-Position (Three-Row Housings, Two Rows Loaded) Housing Assembly with Cover (Preassembled) 78.74 [3.100] 3.48 [.137] Row A 10.49 8.46 [.413] [.333] 8.46 [.333] Row B 84.89 [3.342] Row C 89.92 [3.54] 94.74 [3.730] Housing Assembly Cover Material and Finish Housing and Cover -- UL 94V-0 rated thermoplastic, black Contacts -- Phosphor bronze, duplex plated 0.00076 [.000030] gold on post/pin mating end, 0.00254-0.00508 [.000100-.000200] tin on termination end, with entire contact underplated 0.00127 [.000050] nickel. 6.35 [.250] 10.95 [.431] Related Product Data Mateable Pin Connectors -- Eurocard Type C and Type R-- Selection Guide 82650, See Catalog 82721 Ribbon Cable -- Part Number 2-57040-2 or Part Number 2-57034-5 (64 conductor) Application Tooling -- pages 70-74 14.43 [.568] 18.57 [.731] Terminated 84.66 [3.333] Technical Documents Product Specifications 108-46003 EUROLATCH Receptacles DIN 41612 IEC 603-2 Instruction Sheet 408-9156 I Certified by the Canadian Standards Association, File No. LR 7189 1.27 [.050] 2.79 Dia. [.110] Dia. (2 Holes) R R Contact Rows Loaded A and C Receptacle Kit No. (Preassembled) 746603-4 Note: All part numbers are RoHS compliant. 47 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 .050 [1.27] Centerline Ribbon Cable Connectors EUROLATCH Receptacles 64-Position I Recognized under the Component Program of the Underwriters Laboratories, Inc. UL File No. E28476 2.54 [.100] Ribbon Cable Interconnect Solutions AMP-LATCH Novo Connectors Product Facts .050 [1.27] Centerline Ribbon Cable Connectors AMP-LATCH Novo Connectors I I I I I I I I I I I I I .100 x .100 [2.54 x 2.54] mating grid for .050 [1.27] pitch ribbon cable Tuning fork contact offers a military approved design, at an economical cost Polarization options include military, center and military, and dual bar Choice of duplex gold plating on contact mating area Insulation displacement contacts for fast, economical mass terminations Contact design provides uniform latching of contacts and housing with connector cover Housing, cover and strain relief made of UL 94V-0 rated thermoplastic material Selected 10 thru 64-position configurations available Accepts wire size range 28-26 AWG [0.08-0.15 mm2], solid or stranded Snap-on strain relief and choice of pull loops available One-step termination with Novo tooling Recognized under the Component Program of the Underwriters Laboratories, Inc. UL File No. E28476 Certified by the Canadian Standards Association, File No. LR 7189 R R AMP-LATCH Novo receptacles offer a dual contact interface with all normal force created by metal-tometal contact. This provides a higher degree of contact reliability. AMP-LATCH Novo receptacles feature two rows of contacts on .100 x .100 [2.54 x 2.54] centerlines in select sizes from 10 to 64 positions. Contacts mate with .0252 [0.642] or round posts with .245 [6.22] max. and .175 [4.45] min. lengths. The AMP-LATCH Novo tuning fork contact offers a military-approved design, and at a lower cost. with .000050 [0.00127] nickel. Housings are made of UL 94V-0 thermoplastic material and feature military, military and center, and dual bar polarization. Optional accessories include a snap-on strain relief and pull loops. AMP-LATCH Novo receptacles can be terminated to .050 [1.27] pitch ribbon cable by a wide variety of one-step application tooling. Assemblies are packaged in tubes for ease of handling, protection and termination. Contacts are made of phosphor bronze and are available in a choice of duplex .000015 [0.00038] or .000030 [0.00076] gold in the mating area, and .000100 [0.00254] tin in the termination area, with the entire contact underplated 48 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions AMP-LATCH Novo Receptacles, Military Polarized* .100 x .100 [2.54 x 2.54] Centers .460 [11.68] C .100 [2.54] .135 [3.43] .050 [1.27] Centerline Ribbon Cable Connectors AMP-LATCH Novo Connectors Housing Assembly with Cover (Preassembled) and Strain Relief (Optional) .240 [6.10] .100 [2.54] * Position No. 1 Index Slot Contacts mate with .025 [0.64] sq. or round pins with .245 [6.22] max. and .175 [4.45] min. lengths. .329 [8.36] .093 [2.36] Material and Finish Housing, Cover & Strain Relief -- UL 94V-0 rated thermoplastic, black Contacts -- Phosphor bronze, duplex plated (See chart below) .464 .422 [10.72] [11.79] Ref. Ref. .629 [15.98] Ref. B Terminated with Cover and Strain Relief A Mateable Pin Headers -- Universal -- pages 84-95 Low Profile -- pages 76-83 Mateable Universal I/O Pin Connectors -- pages 45 and 46 .100 [2.54] A Dimensions B C 10 .450 11.43 .680 17.27 .400 10.16 14 .650 16.51 .880 22.35 .600 15.24 16 .750 19.05 .980 24.89 .700 17.78 20 .950 24.13 1.180 29.97 .900 22.86 24 1.150 29.21 1.380 35.05 1.100 27.94 26 1.250 31.75 1.480 37.59 1.200 30.48 30 1.450 36.83 1.680 42.67 1.400 35.56 34 1.650 41.91 1.880 47.75 1.600 40.64 40 1.950 49.53 2.180 55.37 1.900 48.26 50 2.450 62.23 2.680 68.07 2.400 60.96 60 2.950 74.93 3.180 80.77 2.900 73.66 64 3.150 80.01 3.380 85.85 3.100 78.74 No. of Pos. Pull Tabs -- page 63 Keying Plug -- page 64 Pull Loops -- page 66 Strain Relief Dimensional Information -- page 68 Application Tooling -- pages 70-74 Technical Documents Product Specifications 108-40000 Novo and Novo Stackable Receptacles; 108-40004 Ribbon Cable, PVC Insulated Application Specification 114-40005 Ribbon Cable Connectors Instruction Sheets Instructional material covering operation, setup, maintenance, repair, etc. is included with each machine, tool or die set. If this material is required prior to receiving your tooling, call Tyco Electronics at the numbers listed below for the applicable documents. is no polarization slot on * There this end of 10- and 14-position receptacles. Housing Assembly and Cover Accessories .570 [14.48] Ref. .650 [16.51] Ref. Terminated with Cover .106 [2.69] Related Product Data Cover Housing Assembly Contact Plating Strain Relief Part No. Receptacle (Preassembled) Duplex1 Duplex2 Duplex1 Duplex2 Duplex1 Duplex2 Duplex1 Duplex2 Duplex1 Duplex2 Duplex1 Duplex2 Duplex1 Duplex2 Duplex1 Duplex2 Duplex1 Duplex2 Duplex1 Duplex2 Duplex1 Duplex2 Duplex1 Duplex2 499252-5 499252-5 499252-9 499252-9 499252-8 499252-8 499252-2 499252-2 1-499252-0 1-499252-0 499252-3 499252-3 1-499252-2 1-499252-2 499252-6 499252-6 499252-1 499252-1 499252-4 499252-4 499252-7 499252-7 1-499252-3 1-499252-3 1658620-1 1658623-1 1658620-2 1658623-2 1658620-3 1658623-3 1658620-4 1658623-4 1658620-5 1658623-5 1658620-6 1658623-6 1658620-7 1658623-7 1658620-8 1658623-8 1658620-9 1658623-9 1-1658620-0 1-1658623-0 -- -- 1-1658620-2 -- 1.000015 [0.00038] gold or gold flash over palladium-nickel .000015 [0.00038] min. total on post/pin mating end, .000100-.000200 [0.00254-0.00508] tin on termination end, with entire contact underplated .000050 [0.00127] nickel. [0.00076] gold or gold flash over palladium-nickel .000030 [0.00076] min. total on post/pin mating end, .000100-.000200 [0.00254-0.00508] tin on termination end, with entire contact underplated .000050 [0.00127] nickel. Note: These receptacles include a housing assembly and cover (preassembled). Strain reliefs may be purchased separately using the component part nos. listed above. All part numbers are RoHS compliant. 2.000030 *These receptacles can be used in applications requiring non-polarization, as well as military polarization. 49 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions AMP-LATCH Novo Receptacles, Center and Military Polarized* .100 x .100 [2.54 x 2.54] Centers .050 [1.27] Centerline Ribbon Cable Connectors AMP-LATCH Novo Connectors Housing Assembly with Cover (Preassembled) and Strain Relief (Optional) .140 [3.56] C .460 [11.68] .100 [2.54] .240 [6.10] .130 [3.30] D Polarization Bar D * .100 [2.54] Housing Assembly .329 [8.36] .093 [2.36] Material and Finish Housing, Cover & Strain Relief -- UL 94V-0 rated thermoplastic, black Contacts -- Phosphor bronze, duplex plated (See chart below) .629 [15.98] Ref. .570 [14.48] Ref. .650 [16.51] Ref. B Mateable Pin Headers -- Universal -- pages 84-95 Low Profile -- pages 76-83 Mateable Universal I/O Pin Connectors -- pages 45 and 46 Terminated with Cover and Strain Relief A .100 [2.54] Related Product Data is no polarization slot on * There this end of 10- and 14-position receptacles. Housing Assembly and Cover No. of Pos. Dimensions B C A D 10 .450 11.43 .680 17.27 .400 10.16 .275 6.99 14 .650 16.51 .880 22.35 .600 15.24 .375 9.53 16 .750 19.05 .980 24.89 .700 17.78 .425 10.80 20 .950 24.13 1.180 29.97 .900 22.86 .525 13.34 24 1.150 29.21 1.380 35.05 1.100 27.94 .625 15.88 26 1.250 31.75 1.480 37.59 1.200 30.48 .675 17.15 30 1.450 36.83 1.680 42.67 1.400 35.56 .775 19.69 34 1.650 41.91 1.880 47.75 1.600 40.64 .875 22.23 40 1.950 49.53 2.180 55.37 1.900 48.26 1.025 26.04 50 2.450 62.23 2.680 68.07 2.400 60.96 1.275 32.39 60 2.950 74.93 3.180 80.77 2.900 73.66 1.525 38.74 64 3.150 80.01 3.380 85.85 3.100 78.74 1.625 41.28 Technical Documents Product Specifications 108-40000 AMP-LATCH Novo and AMP-LATCH Novo Stackable Receptacles; 108-40004 Ribbon Cable, PVC Insulated Application Specification 114-40005 Novo Receptacles Instruction Sheets Instructional material covering operation, setup, maintenance, repair, etc. is included with each machine, tool or die set. If this material is required prior to receiving your tooling, call Tyco Electronics at the numbers listed below for the applicable documents. .422 .464 [10.72] [11.79] Ref. Ref. Terminated with Cover .106 [2.69] Pull Tabs -- page 63 Keying Plug -- page 64 Pull Loops -- page 66 Strain Relief -- page 68 Application Tooling -- pages 70-74 Cover Position No. 1 Index Slot Contacts mate with .025 [0.64] sq. or round pins with .245 [6.22] max. and .175 [4.45] min. lengths. Accessories .135 [3.43] Contact Plating Strain Relief Part No. Duplex1 Duplex2 Duplex1 Duplex2 Duplex1 Duplex2 Duplex1 Duplex2 Duplex1 Duplex2 Duplex1 Duplex2 Duplex1 Duplex2 Duplex1 Duplex2 Duplex1 Duplex2 Duplex1 Duplex2 Duplex1 Duplex2 Duplex1 Duplex2 499252-5 499252-5 499252-9 499252-9 499252-8 499252-8 499252-2 499252-2 1-499252-0 1-499252-0 499252-3 499252-3 1-499252-2 1-499252-2 499252-6 499252-6 499252-1 499252-1 499252-4 499252-4 499252-7 499252-7 1-499252-3 1-499252-3 Receptacle (Preassembled) 1658621-1 1658622-1 1658621-2 1658622-2 1658621-3 1658622-3 1658621-4 1658622-4 1658621-5 1658622-5 1658621-6 1658622-6 1658621-7 1658622-7 1658621-8 1658622-8 1658621-9 1658622-9 1-1658621-0 1-1658622-0 1-1658621-1 1-1658622-1 1-1658621-2 1-1658622-2 1.000015 *These receptacles can be used in applications requiring center polarization. [0.00038] gold or gold flash over palladium-nickel .000015 [0.00038] min. total on post/pin mating end, .000100-.000200 [0.00254-0.00508] tin on termination end, with entire contact underplated .000050 [0.00127] nickel. 2.000030 [0.00076] gold or gold flash over palladium-nickel .000030 [0.00076] min. total on post/pin mating end, .000100-.000200 [0.00254-0.00508] tin on termination end, with entire contact underplated .000050 [0.00127] nickel. Note: These receptacles include a housing assembly and cover (preassembled). Strain reliefs may be purchased separately using the component part nos. listed above. All part numbers are RoHS compliant. 50 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions AMP-LATCH Novo Receptacles, Dual Polarized, .100 x .100 [2.54 x 2.54] Centers .140 [3.56] C .460 [11.68] .100 [2.54] .135 [3.43] .050 [1.27] Centerline Ribbon Cable Connectors AMP-LATCH Novo Connectors Housing Assembly with Recessed Cover (Preassembled) and Strain Relief (Optional) .240 [6.10] .100 [2.54] .140 [3.56] Material and Finish .190 [4.83] Housing, Cover & Strain Relief -- UL 94V-0 rated thermoplastic, black Contacts -- Phosphor bronze, duplex plated .000030 [0.00076] gold or gold flash over palladium-nickel .000030 [0.00076] min. total on post/pin mating end, .000100-.000200 [0.002540.00508] tin on termination end, with entire contact underplated .000050 [0.00127] nickel. Housing Assembly Cover Position No. 1 Index Slot .329 [8.36] .093 [2.36] .422 .464 [10.72] [11.79] Ref. Ref. .629 [15.98] Ref. .570 [14.48] Ref. .650 [16.51] Ref. Terminated with Cover Related Product Data Mateable Pin Headers -- Universal -- pages 84-95 Low Profile -- pages 76-83 Mateable Universal I/O Pin Connectors -- pages 45 and 46 B Terminated with Cover and Strain Relief A .106 [2.69] .100 [2.54] Accessories Pull Tabs -- page 63 Keying Plug -- page 64 Pull Loops -- page 66 Strain Relief -- page 68 Application Tooling -- pages 70-74 Housing Assembly and Cover No. of Pos. Technical Documents Product Specifications 108-40000 AMP-LATCH Novo and AMP-LATCH Novo Stackable Receptacles; 108-40004 Ribbon Cable, PVC Insulated Application Specification 114-40005 AMP-LATCH Novo Receptacles Instruction Sheets Instructional material covering operation, setup, maintenance, repair, etc. is included with each machine, tool or die set. If this material is required prior to receiving your tooling, call Tyco Electronics at the numbers listed below for the applicable documents. 10 14 16 20 24 26 30 34 40 50 64 A .450 11.43 .650 16.51 .750 19.05 .950 24.13 1.150 29.21 1.250 31.75 1.450 36.83 1.650 41.91 1.950 49.53 2.450 62.23 3.150 80.01 Dimensions B C .680 .400 17.27 10.16 .880 .600 22.35 15.24 .980 .700 24.89 17.78 1.180 .900 29.97 22.86 1.380 1.100 35.05 27.94 1.480 1.200 37.59 30.48 1.680 1.400 42.67 35.56 1.880 1.600 47.75 40.64 2.180 1.900 55.37 48.26 2.680 2.400 68.07 60.96 3.380 3.100 85.85 78.74 Strain Relief Part No. Receptacle (Preassembled) 499252-5 1658624-1 499252-9 1658624-2 499252-8 1658624-3 499252-2 1658624-4 1-499252-0 1658624-5 499252-3 1658624-6 1-499252-2 1658624-7 499252-6 1658624-8 499252-1 1658624-9 499252-4 1-1658624-0 1-499252-3 1-1658624-2 Note: All part numbers are RoHS compliant. 51 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 METRIC Dimensions are millimeters over inches Ribbon Cable Interconnect Solutions Female Socket Connectors, .100 x .100 [2.54 x 2.54] Centers, 622 and 636 Series Technical Data .050 [1.27] Centerline Ribbon Cable Connectors Female Socket Connectors, .100 x .100 [2.54 x 2.54] Centers, 622 and 636 Series Color -- 622 Series, Blue; 636 Series, Black Contact Material -- 622 Series, Beryllium copper; 636 Series, Phosphor bronze Contact Plating -- 622 Series, .000030 [0.00076] min. gold on mating end, .000100-.000200 [0.002540.00508] tin on termination end, both over .000050 [0.00127] nickel underplate; 636 Series, .000015 [0.00038] min. gold on mating end, .000100.000200 [0.00254-0.00508] tin on termination end, both over .000050 [0.00127] nickel underplate. Housing Material -- Glass-filled thermoplastic, UL 94V-0 rated Cable -- 26-28 AWG solid or stranded, PVC insulated ribbon cable Mateable Connectors -- Universal and Low Profile Pin Headers -- pages 76-95 Universal I/O Ribbon Cable Connectors -- pages 45 and 46 Polarization -- Military and center polarized only I I Recognized under the Component Program of the Underwriters Laboratories, Inc. UL File No. E60980 Certified by the Canadian Standards Association, File No. LR 92984 R R Application Tooling Die -- 1437000-9 [T&B# 779-2151 ref.] Handtool -- 1437000-6 [T&B# 779-2100 ref.] Bench Press (Manual) -- 1437001-4 [T&B# 779-3200 ref.] Bench Press Platen -- 5-1437000-6 [T&B# 779-3130 ref.] Bench Press Base Plate -- 6-1437000-4 [T&B# 779-3151 ref.] Accessories Strain Relief -- page 69 Pull Loops -- page 66 Keying Plug -- page 64 52 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Female Socket Connectors, .100 x .100 [2.54 x 2.54] Centers, 622 and 636 Series (Continued) 622 Series Part Numbers 6 10 12 14 16 20 24 26 30 34 40 50 64 A .477 12.12 .677 17.20 .777 19.74 .877 22.28 .977 24.82 1.177 29.90 1.377 34.98 1.477 37.52 1.677 42.60 1.877 47.68 2.177 55.30 2.677 68.00 3.377 85.78 Dimensions B C .200 5.08 .400 10.16 .500 12.70 .600 15.24 .700 17.78 .900 22.86 1.100 27.94 1.200 30.48 1.400 35.56 1.600 40.64 1.900 48.26 2.400 60.96 3.100 78.74 .075 1.91 .126 3.20 .150 3.81 .150 3.81 .150 3.81 .150 3.81 .150 3.81 .150 3.81 .150 3.81 .150 3.81 .150 3.81 .150 3.81 .150 3.81 Connector w/ Strain Relief T&B T&B Tyco Electronics (Reference Only) Tyco Electronics (Reference Only) 1658527-2 622-0630LF 1-1658527-9 622-0641LF 1658527-3 622-1030LF 1658527-4 622-1041LF 2-1658527-0 622-1230LF -- -- 1658527-5 622-1430LF 2-1658527-2 622-1441LF 1658527-6 622-1630LF 1658527-7 622-1641LF 2-1658527-3 622-2030LF 1658527-8 622-2041LF -- -- 2-1658527-5 622-2441LF 622-2630LF 1-1658527-0 622-2641LF -- -- 2-1658527-7 622-3041LF -- -- 2-1658527-8 622-3441LF 1-1658527-2 622-4030LF 1-1658527-3 622-4041LF 1-1658527-4 622-5030LF 1-1658527-5 622-5041LF -- -- 3-1658527-2 622-6441LF 1658527-9 .050 [1.27] Centerline Ribbon Cable Connectors Female Socket Connectors, .100 x .100 [2.54 x 2.54] Centers, 622 and 636 Series No.of Pos. Connector Only Note: Order by Tyco Electronics Part Number only. Original non-RoHS compliant T&B number may be determined by dropping the "LF" suffix. 636 Series Part Numbers No.of Pos. 6 10 14 16 20 24 26 34 40 50 64 Note: All part numbers are RoHS compliant. A .477 12.12 .677 17.20 .877 22.28 .977 24.82 1.177 29.90 1.377 34.98 1.477 37.52 1.877 47.68 2.177 55.30 2.677 68.00 3.377 85.78 Dimensions B C .200 5.08 .400 10.16 .600 15.24 .700 17.78 .900 22.86 1.100 27.94 1.200 30.48 1.600 40.64 1.900 48.26 2.400 60.96 3.100 78.74 .075 1.91 .126 3.20 .150 3.81 .150 3.81 .150 3.81 .150 3.81 .150 3.81 .150 3.81 .150 3.81 .150 3.81 .150 3.81 Connector Only Connector w/ Strain Relief T&B T&B Tyco Electronics (Reference Only) Tyco Electronics (Reference Only) 1-1658528-0 636-0630LF -- 1-1658528-1 636-1030LF 1-1658528-2 636-1430LF 1-1658528-4 636-1630LF 1658528-5 636-1641LF 1-1658528-5 636-2030LF 1658528-4 636-2041LF 1-1658528-6 636-2430LF -- -- 1-1658528-7 636-2630LF -- -- -- -- 1658528-6 636-3441LF -- -- 1-1658528-9 636-4041LF 2-1658528-0 636-5030LF 1658528-8 636-5041LF -- -- 2-1658528-3 636-6441LF 1658528-2 -- -- 636-1041LF -- Note: Order by Tyco Electronics Part Number only. Original non-RoHS compliant T&B number may be determined by dropping the "LF" suffix. 53 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 METRIC Dimensions are millimeters over inches Ribbon Cable Interconnect Solutions Female Socket Connectors, .100 x .100 [2.54 x 2.54] Centers, 609 Series Technical Data .050 [1.27] Centerline Ribbon Cable Connectors Female Socket Connectors, .100 x .100 [2.54 x 2.54] Centers, 609 Series Color -- Blue Contact Material -- Beryllium copper Contact Plating -- .000030 [0.00076] min. gold on mating end, .000100.000200 [0.00254-0.00508] tin on termination end, both over .000050 [0.00127] nickel underplate. Housing Material -- Glass-filled thermoplastic, UL 94V-0 rated Cable -- 28-30 AWG solid or stranded, PVC insulated ribbon cable Mateable Connectors -- Universal and Low Profile Pin Headers -- pages 76-95 Universal I/O Ribbon Cable Connectors -- pages 45 and 46 Polarization -- Military only or military and center polarized I I Recognized under the Component Program of the Underwriters Laboratories, Inc. UL File No. E60980 Dual Slot IDC Design Optional Center Polarization 3.30 [.130] R Certified by the Canadian Standards Association, File No. LR 92984 R Application Tooling Die -- 1437000-9 [T&B# 779-2151 ref.] Handtool -- 1437000-6 [T&B# 779-2100 ref.] Bench Press (Manual) -- 1437001-4 [T&B# 779-3200 ref.] Bench Press Platen -- 5-1437000-6 [T&B# 779-3130 ref.] Bench Press Base Plate -- 6-1437000-4 [T&B# 779-3151 ref.] Standard Socket Connector Without Strain Relief Accessories Strain Relief -- page 67 Pull Loops -- page 66 Keying Plug -- page 64 Note: All part numbers are RoHS compliant. 54 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Female Socket Connectors, .100 x .100 [2.54 x 2.54] Centers, 609 Series (Continued) 609 Series, Military Polarized Part Numbers No.of Pos. 10 16 20 26 40 50 .476 12.09 .676 17.17 .976 24.79 1.176 29.87 1.476 37.49 2.176 55.27 2.676 67.97 Dimensions B C .200 5.08 .400 10.16 .700 17.78 .900 22.86 1.200 30.48 1.900 48.26 2.400 60.96 .392 9.96 .592 15.04 .892 22.66 1.092 27.74 1.392 35.36 2.092 53.14 2.592 65.84 Connector w/ Strain Relief T&B T&B Tyco Electronics (Reference Only) Tyco Electronics (Reference Only) 2-1658526-5 609-0600MLF -- -- 1658526-3 609-1000MLF -- -- -- -- 1-1658526-0 609-1601MLF 3-1658526-0 609-2000MLF -- -- 3-1658526-5 609-2600MLF -- -- 4-1658526-1 609-4000MLF -- -- 4-1658526-3 609-5000MLF 2-1658526-2 609-5001MLF .050 [1.27] Centerline Ribbon Cable Connectors Female Socket Connectors, .100 x .100 [2.54 x 2.54] Centers, 609 Series 6 A Connector Only Note: Order by Tyco Electronics Part Number only. Original non-RoHS compliant T&B number may be determined by dropping the "LF" suffix. 609 Series, Military and Center Polarized Part Numbers No.of Pos. 6 10 14 16 20 24 26 34 36 40 50 64 A .476 12.09 .676 17.17 .876 22.25 .976 24.79 1.176 29.87 1.376 34.95 1.476 37.49 1.876 47.65 1.976 50.19 2.176 55.27 2.676 67.97 3.376 85.75 Dimensions B C .200 5.08 .400 10.16 .600 15.24 .700 17.78 .900 22.86 1.100 27.94 1.200 30.48 1.600 40.64 1.700 43.18 1.900 48.26 2.400 60.96 3.100 78.74 .392 9.96 .592 15.04 .792 20.12 .892 22.66 1.092 27.74 1.292 32.82 1.392 35.36 1.792 45.52 1.892 48.06 2.092 53.14 2.592 65.84 3.292 83.62 Connector Only Connector w/ Strain Relief T&B T&B Tyco Electronics (Reference Only) Tyco Electronics (Reference Only) 1658526-1 609-0630LF 1658526-2 609-0641LF 1658526-4 609-1030LF 1658526-5 609-1041LF 1658526-8 609-1430LF 1658526-9 609-1441LF 2-1658526-9 609-1630LF 1-1658526-1 609-1641LF 1-1658526-2 609-2030LF 1-1658526-3 609-2041LF 1-1658526-4 609-2430LF -- -- 1-1658526-5 609-2630LF 1-1658526-6 609-2641LF 1-1658526-8 609-3430LF 1-1658526-9 609-3441LF 3-1658526-8 609-3630LF 4-1658526-0 609-3641LF 2-1658526-0 609-4030LF 2-1658526-1 609-4041LF 2-1658526-3 609-5030LF 2-1658526-4 609-5041LF 4-1658526-4 609-6430LF 4-1658526-5 609-6441LF Note: Order by Tyco Electronics Part Number only. Original non-RoHS compliant T&B number may be determined by dropping the "LF" suffix. Note: All part numbers are RoHS compliant. 55 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions DIP Plugs, .100 x .100 [2.54 x 2.54] Centers, 609 Series Technical Data .050 [1.27] Centerline Ribbon Cable Connectors DIP Plugs, .100 x .100 [2.54 x 2.54] Centers, 609 Series Color -- Blue Contact Material -- Beryllium copper Contact Plating -- .000100-.000200 [0.00254-0.00508] tin over .000050 [0.00127] nickel underplate. Contact Design -- Dual slot, barrel shaped ("tulip") IDC with solder tail Housing Material -- Glass-filled thermoplastic, UL 94V-0 rated Cable -- 28-30 AWG solid or stranded, PVC insulated ribbon cable Mateable Connectors -- .100 x .100 DIP sockets .280 [7.1] A .100 [2.54] .319 Before [8.1] Crimping .008 x .024 [0.2 x 0.6] Application Tooling Die -- 1-1437000-3 [T&B# 779-2153 ref.] Handtool -- 1437000-6 [T&B# 779-2100 ref.] Bench Press (Manual) -- 1437001-4 [T&B# 779-3200 ref.] Bench Press Platen -- 5-1437000-6 [T&B# 779-3130 ref.] Bench Press Base Plate -- 6-1437000-7 [T&B# 779-3153 ref.] .100 [2.54] .100 [2.54] No.of Pos. 6 10 14 16 20 26 34 Dimensions A B .512 13.00 .713 18.11 .913 23.19 1.010 25.65 1.213 30.81 1.512 38.40 1.913 48.59 .200 5.08 .400 10.16 .600 15.24 .700 17.78 .900 22.86 1.200 30.48 1.600 40.64 B Part Numbers Tyco Electronics T&B (Reference Only) 1437006-4 609-0653 1437006-7 609-1053 1-1437006-0 609-1453 1-1437006-3 609-1653 1-1437006-6 609-2053 2-1437006-1 609-2653 2-1437006-4 609-3453 Note: Order by Tyco Electronics Part Number only. All part numbers listed above are found on Tyco Electronics customer drawing 1437006-4. All part numbers are RoHS compliant. 56 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions DIP Plugs, .100 x .100 [2.54 x 2.54] Centers, 622 Series 7.57 (.298) Technical Data .050 [1.27] Centerline Ribbon Cable Connectors DIP Plugs, .100 x .100 [2.54 x 2.54] Centers, 622 Series Color -- Blue Contact Material -- Beryllium copper Contact Plating -- .000100-.000200 [0.00254-0.00508] tin over .000050 [0.00127] nickel underplate. Contact Design -- Single slot, flat, tuning fork style IDC with solder tail Housing Material -- Glass-filled thermoplastic, UL 94V-0 rated Cable -- 26-28 AWG solid or stranded, PVC insulated ribbon cable Mateable Connectors -- .100 x .100 DIP sockets Application Tooling Die -- 1-1437000-3 [T&B# 779-2153 ref.] Handtool -- 1437000-6 [T&B# 779-2100 ref.] Bench Press (Manual) -- 1437001-4 [T&B# 779-3200 ref.] Bench Press Platen -- 6-1437000-1 [T&B# 779-3133 ref.] Bench Press Base Plate -- 6-1437000-7 [T&B# 779-3153 ref.] No.of Pos. 6 Accessories Strain Relief -- page 65 8 10 14 16 20 24 26 34 36 40 50 60 64 Dimensions A B .506 12.85 .606 15.39 .706 17.93 .906 23.01 1.006 25.55 1.206 30.63 1.406 35.71 1.506 38.25 1.906 48.41 2.006 50.95 2.206 56.03 2.706 68.73 3.206 81.43 3.406 86.51 .200 5.08 .300 7.62 .400 10.16 .600 15.24 .700 17.78 .900 22.86 1.100 27.94 1.200 30.48 1.600 40.64 1.700 43.18 1.900 48.26 2.400 60.96 2.900 73.66 3.100 78.74 Part Numbers T&B (Reference Only) Tyco Electronics 1658525-4 622-0653LF 1658525-5 622-0853LF 1658525-6 622-1053LF 1658525-7 622-1453LF 1658525-8 622-1653LF 1658525-9 622-2053LF 1-1658525-0 622-2453LF 1658525-1 622-2653LF 1658525-2 622-3453LF 1-1658525-2 622-3653LF 1-1658525-3 622-4053LF 1658525-3 622-5053LF 1-1658525-5 622-6053LF 1-1658525-6 622-6453LF Notes: Order by Tyco Electronics Part Number only. All part numbers are RoHS compliant. 57 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions DIP Plugs, .100 x .100 [2.54 x 2.54] Centers Housing Assembly with Cover (Preassembled) B C .050 [1.27] .278 [7.06] .100 [2.54] A .050 [1.27] A .050 [1.27] Material and Finish .050 [1.27] Centerline Ribbon Cable Connectors DIP Plugs, .100 x .100 [2.54 x 2.54] Centers Housing and Cover -- Black thermoplastic, UL 94V-0 rated Contacts -- Phosphor bronze, plated .000005 [0.000127] min. gold in termination area, .000100 [0.00254] min. tin on solder tails, both over .000050 [0.00127] nickel on entire contact Contact Design -- Flat, tuning fork style IDC .396* [10.06] .113 [2.87] .156 [3.96] .100 [2.54] Related Product Data Application Tooling -- pages 70-74 Product Specification 108-1538 DIP Plug Instruction Sheets Instructional material covering operation, setup, maintenance, repair, etc. is included with each machine, tool or die set. If this material is required prior to receiving your tooling, call Tyco Electronics at the numbers listed below for the applicable documents. Mateable Connectors -- For Connectors without Retention Legs -- .100 x .100 DIP Sockets No. of Pos. 10 14 16 20 24 26 30 C .100 [2.54] 34 40 44 .100 [2.54] 50 60 PCB Layout .019 [0.48] .013 [0.33] *Height of connector after termination is .253 [6.43] ref. .100 [2.54] Technical Documents .035 Dia. [0.89] (After Plating) C 64 A .450 11.43 .650 16.51 .750 19.05 .950 24.13 1.150 29.21 1.250 31.75 1.450 36.83 1.650 41.91 1.950 49.53 2.150 54.61 2.450 62.23 2.950 74.93 3.150 80.01 Dimensions B .680 17.27 .880 22.35 .980 24.89 1.180 29.97 1.380 35.05 1.480 37.59 1.680 42.67 1.880 47.75 2.180 55.37 2.380 60.45 2.680 68.07 3.180 80.77 3.380 85.85 C .400 10.16 .600 15.24 .700 17.78 .900 22.86 1.100 27.94 1.200 30.48 1.400 35.56 1.600 40.64 1.900 48.26 2.100 53.34 2.400 60.96 2.900 73.66 3.100 78.74 DIP Plugs (Preassembled) With Retention Legs 2-746610-1 1-111382-4 2-746610-2 -- 1-746610-4 1-111382-6 1-746610-5 1-111382-7 2-746610-3 -- 1-746610-6 1-111382-8 1-746610-7 -- 1-746610-8 1-111382-9 1-746610-9 -- 2-746610-6 -- 2-746610-0 2-111382-0 2-746610-4 -- 2-746610-5 -- Notes: All plug kits include a housing assembly and cover (preassembled). All part numbers are RoHS compliant. 58 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions DIP Plugs, .100 x .300 [2.54 x 7.62] Centers Housing Assembly with Cover (Preassembled) Material and Finish .050 [1.27] Centerline Ribbon Cable Connectors DIP Plugs, .100 x .300 [2.54 x 7.62] Centers Housing and Cover -- Black thermoplastic, UL 94V-0 rated Contacts -- Phosphor bronze, plated .000050 [0.00127] nickel underplate on entire contact, .000005 [0.000127] min. gold on termination (IDC) end. See table for leg finish. Contact Design -- Flat, tuning fork style IDC Related Product Data Application Tooling -- pages 70-74 Technical Documents Product Specification 108-1538 DIP Plug Ribbon Cable Requirements -- 28 AWG stranded or 26, 28 and 30 AWG solid wire .300 [7.62] Recommended Mounting Hole Pattern (for .094-.125 [2.39-3.18] thick pc boards) Dimensions B C No. of Pos. A 8 .350 8.89 .488 12.40 .300 7.62 14 .650 16.51 .788 20.02 .600 15.24 16 .750 19.05 .888 22.56 .700 17.78 18 .850 21.59 .988 25.10 .800 20.32 20 .950 24.13 1.088 27.64 .900 22.86 Contact Plating DIP Plugs (Preassembled) Duplex1 Duplex2 Duplex3 Duplex1 Duplex2 Duplex3 Duplex1 Duplex2 Duplex3 Duplex1 Duplex2 Duplex3 Duplex1 Duplex2 Duplex3 746611-7 -- 5746613-1 746611-8 5746612-2 5746613-2 746611-6 5746612-3 5746613-3 746611-9 -- -- 1-746611-0 -- -- .000030 [0.00076] gold on leg .000015 [0.00038] gold on leg 3 .000100 [0.00254] tin on leg Note: All part numbers are RoHS compliant. 1 2 59 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions DIP Plugs, .100 x .600 [2.54 x 15.24] Centers Housing Assembly with Cover (Preassembled) Material and Finish .050 [1.27] Centerline Ribbon Cable Connectors DIP Plugs, .100 x .600 [2.54 x 15.24] Centers Housing and Cover -- Black thermoplastic, UL 94V-0 rated Contacts -- Phosphor bronze, plated .000050 [0.00127] nickel underplate on entire contact, .000005 [0.000127] min. gold on termination (IDC) end. See table for leg finish. Contact Design -- Flat, tuning fork style IDC Related Product Data Application Tooling -- pages 70-74 Technical Documents Product Specification 108-1538 DIP Plug Ribbon Cable Requirements -- 28 AWG stranded or 26, 28 and 30 AWG solid wire No. of Pos. 24 28 40 A 1.150 29.21 1.350 34.29 1.950 49.53 Dimensions B C 1.288 1.100 32.72 27.94 1.488 1.300 37.80 33.02 2.088 1.900 53.04 48.26 Contact Plating DIP Plugs (Preassembled) Duplex1 5746615-1 Duplex1 5746615-2 Duplex1 5746615-3 .000015 [0.00038] gold on leg Note: All part numbers are RoHS compliant. 1 Recommended Mounting Hole Pattern (for .094-.125 [2.39-3.18] thick pc boards) 60 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions 4-Row PCB Solder Transition Connectors Technical Data Color -- Blue Contact Material -- Beryllium copper Contact Plating -- .000100-.000200 [0.00254-0.00508] tin over .000050 [0.00127] nickel underplate. Contact Design -- Dual slot, barrel shaped ("tulip") IDC with solder tail Housing Material -- Glass-filled thermoplastic, UL 94V-0 rated Cable -- 28-30 AWG solid or stranded, PVC insulated ribbon cable .050 [1.27] Centerline Ribbon Cable Connectors 4-Row PCB Solder Transition Connectors Application Tooling Die -- 1-1437000-3 [T&B# 779-2153 ref] Handtool -- 1437000-6 [T&B# 779-2100 ref] Bench Press (Manual) -- 1437001-4 [T&B# 779-3200 ref] Bench Press Platen -- 5-1437000-6 [T&B# 779-3130 ref] Bench Press Base Plate -- 6-1437000-7 [T&B# 779-3153 ref] 609 Series, Military Polarized No.of Pos. 10 14 16 20 26 34 44 50 Dimensions A B .710 18.03 .910 23.11 1.010 25.65 1.210 30.73 1.510 38.35 1.910 48.51 2.410 61.21 2.710 68.83 .450 11.43 .650 16.51 .750 19.05 .950 24.13 1.250 31.75 1.650 41.91 2.150 54.61 2.450 62.23 Part Numbers .100 Tail Length .156 Tail Length Tyco Electronics T&B Tyco Electronics T&B (Reference Only) (Reference Only) 6437006-5 609-1003LF -- 6437006-8 609-1403LF 1-6437006-1 609-1603LF -- -- -- -- 1-6437006-5 609-2043LF 1-6437006-8 609-2603LF 2-6437006-0 609-2643LF 2-6437006-2 609-3403LF 2-6437006-3 609-3443LF 2-6437006-9 609-4403LF -- -- -- -- 3-6437006-2 609-5043LF 6437006-9 -- 609-1443LF Notes: Order by Tyco Electronics Part Number only. All part numbers listed above are found on Tyco Electronics Customer Drawing 6437006-5. All part numbers are RoHS compliant. 61 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions 1-Row Horizontal Receptacles A B 1.25 Pitch [.049] 1.35 [.053] 1.40 [.055] 2.80 3.00 [.110] [.118] Optional Mounting Boss 3.40 [.134] 4.20 [.165] Material and Finish Housing -- Black PPS, UL 94V-0 rated Contacts -- Phosphor bronze, post tin plated over nickel underplate 0.70 Min. [.028] 3.40 [.134] .050 [1.27] Centerline Ribbon Cable Connectors 1-Row Horizontal Receptacles 0.05 [.002] 0.50 [.020] C 0.80 [.031] 1.30 [.051] 0.70 Min. [.028] O 0.80 [.031] 1.35 [.053] 0.50 [.020] A PCB Mounting Layout 1.25 Fine Pitch (FP) - 1-Row Horizontal Receptacles No. of Pos. 4 5 6 2.35 Slot Key 7 8 10 17 20 Part Numbers With Mounting Bosses Without Mounting Bosses Tape Bag Tape Bag A Dimensions B C 6.45 .254 7.70 .303 8.95 .352 10.20 .402 11.45 .451 13.95 .549 22.70 .894 26.45 1.041 3.75 .148 5.00 .197 6.25 .246 7.50 .295 8.75 .345 11.25 .443 20.00 .787 23.75 .935 5.45 .215 6.70 .264 7.95 .313 9.20 .362 10.45 .411 12.95 .510 21.70 .854 25.45 1.002 3-175637-4 3-174638-4 3-175629-4 3-174903-4 3-175637-5 3-174638-5 3-175629-5 3-174903-5 3-175637-6 3-174638-6 3-175629-6 3-174903-6 3-175637-7 3-174638-7 3-175629-7 3-174903-7 3-175637-8 3-174638-8 3-175629-8 3-174903-8 4-175637-0 4-174638-0 4-175629-0 4-174903-0 -- 4-174638-7 4-175629-7 4-174903-7 -- 5-174638-0 -- 5-174903-0 62 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Accessories (Continued) Flexible Pull Tabs Approximate Installed Height of Part Number 120623-1 Above Connector Material and Finish Dimensions C H .680 1.806 17.27 45.87 1.749 .880 44.42 22.35 1.721 .980 43.71 24.89 1.180 1.664 29.97 42.27 1.380 1.607 35.05 40.82 1.578 1.480 40.08 37.59 1.680 1.521 42.67 38.63 1.880 1.464 47.75 37.19 1.436 1.980 36.47 50.29 1.379 2.180 35.03 55.37 2.380 1.322 60.45 33.58 2.680 1.236 68.07 31.39 3.180 1.094 80.77 27.79 3.380 1.037 85.85 26.34 No. of Positions Nylon, black 10 Part Number 120623-1 14 Related Product Data 16 AMP-LATCH Novo Connectors -- pages 48-51 Ultra ATA compliant Bus Connectors -- pages 13-15 20 24 26 30 34 36 40 H 44 50 60 64 C Note: Cannot be used together with a strain relief. Accessories Universal I/O Latches Material and Finish .236 [5.99] Polyester, black .108.002 [2.740.05] Mates to Receptacles Related Product Data Without Strain Relief Universal I/O Pin Connectors -- pages 45 and 46 Latch Removal Tool Part Number 91269-1 F With Strain Relief Dimensions F G .416 .768 10.57 19.51 .576 .928 14.63 23.57 Part Number 111451-1 111451-3 Note: All part numbers are RoHS compliant. G Military Polarizers .335 [8.51] .134 [3.40] Material and Finish Thermoplastic, black Break Line Related Product Data Throw-Away Tab Universal I/O Pin Connectors -- pages 45 and 46 Break Line .335 [8.51] .134 [3.40] Part Numbers: 499991-2 (packaged, 50 per bag) 499991-3 (packaged, 1000 per box) The snap-in polarizer provides military polarization. 63 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Accessories (Continued) Keying Plugs Material and Finish Thermoplastic, see table for color Keying Plug Plug (Installed in Contact) Typical Application Key Plug 111620-1 Accessories There are ten key plugs on a comb .500 [12.70] .245 [6.22] .029 [0.58] .185 [4.70] Polarizing Key 1-1437023-2 Receptacle Connector Series 2 mm Rcpt. Connectors Catalog Pages 609 Series Female Socket Connectors 54, 55 622 Series Female Socket Connectors 52, 53 636 Series Female Socket Connectors 52, 53 Keying Plug Part Number Style Color 111620-1 Comb Black Single Blue Single Blue Single Blue 16, 17 1-1437023-2 T&B 609-0000 (Ref.) 1-1437023-2 T&B 609-0000 (Ref.) 1-1437023-2 T&B 609-0000 (Ref.) Order by Tyco Electronics Part Number only. Note: All part numbers are RoHS compliant. 64 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Accessories (Continued) Keying Plugs (Continued) Material and Finish Thermoplastic, see table for color Receptacle Connector Series Part Number 499712-1 Catalog Pages Novo Connectors 48-51 Ultra ATA Bus Connectors 13-15 Keying Plug Part Number 499712-1 104072-1 499712-1 104072-1 Style Single Comb Single Comb Color Black Black Order by Tyco Electronics Part Number only. Note: All part numbers are RoHS compliant. Key Plug (Plugs into Contact) Alternate Configuration Keying Plug Part No. 104072-1 (10 Keying Plugs per Comb) Accessories 65 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Accessories (Continued) Pull Loops, Permanent (for Receptacles and Pin Connectors) Material and Finish Natural color PVC, 94-VTM-1 rating (thin material) Related Product Data Use with: Female Socket Connectors -- pages 52-55 Ultra ATA Compliant Bus Connectors -- pages 13-15 2 mm Receptacle Connectors -- pages 16 and 17 AMP-LATCH Novo Connectors -- pages 48-51 Accessories Note: This pull loop is installed manually between the cover and strain relief, and cannot be used without strain relief. No. of Positions Female Socket Ultra ATA Compliant 2 mm Conns. Bus Connector Rcpt. Conns. AMP-LATCH Novo Conns. 10 -- 12, 14, 16 10 14 -- 20 14 16 -- 22 16 20 -- 24, 26 20 24 -- -- 24 26 -- 30, 34, 40 26 30 -- -- 30 34 -- 44 34 40 40 50 40 50 -- -- 50 60 -- -- 60 Dimension A .44 11.18 .64 16.26 .74 18.80 .88 22.35 1.08 27.43 1.18 29.97 1.38 35.05 1.58 40.13 1.82 46.23 2.32 58.93 2.80 71.12 Pull Loop Part No. 5088450-2 5088450-3 5088450-4 5088450-5 5088450-6 5088450-7 1-5088450-2 5088450-8 5088450-9 1-5088450-0 1-5088450-1 Note: All part numbers are RoHS compliant. 66 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Accessories (Continued) Strain Relief for Universal I/O Pin Connectors Without Mounting Ears C Glass-filled polyester, black No. of Pos. 10 A .330 [8.38] Typ. Material and Finish .313.004 [7.950.10] Typ. 14 .098.002 [2.490.05] 2 Plc. 16 20 Related Product Data B Universal I/O Pin Connectors -- page 45 24 26 30 34 40 44 50 60 64 A .520 13.21 .720 18.29 .820 20.83 1.020 25.91 1.220 30.99 1.320 33.53 1.520 38.61 1.720 43.69 2.020 51.31 2.220 56.39 2.520 64.01 3.020 76.71 3.220 81.79 Dimensions B C .766 .940 19.46 23.88 .966 1.140 24.54 28.96 1.066 1.240 27.08 31.50 1.266 1.440 32.16 36.58 1.466 1.640 37.24 41.66 1.566 1.740 39.78 44.20 1.766 1.940 44.86 49.28 1.966 2.140 49.94 54.36 2.266 2.440 57.56 61.98 2.466 2.640 62.64 67.06 2.766 2.940 70.26 74.68 3.266 3.440 82.96 87.38 3.466 3.640 88.04 92.56 Part Number 111547-1 111547-2 111547-3 111547-4 111547-5 111547-6 111547-7 111547-8 111547-9 1-111547-0 1-111547-1 1-111547-2 1-111547-3 Accessories Strain Relief for 609 Series (Tulip Contact) Female Socket Connectors Material and Finish Glass-filled polyester, blue Related Product Data Female Socket Connectors -- page 54 and 55 .240 [6.10] A .565 [14.35] Standard Version .240 [6.10] Part Number No. of Pos. Dimension A Type 6 .472 11.99 Standard 2-1437020-1 609-0631 10 .672 17.07 14 .872 22.15 16 .972 24.69 20 1.172 29.77 Heavy Duty Standard Heavy Duty Standard Heavy Duty Standard Heavy Duty Standard 3-1437020-7 3-1437020-5 5-1437020-1 4-1437020-9 6-1437020-6 6-1437020-4 8-1437020-6 8-1437020-4 609-1031HD 609-1031 609-1431HD 609-1431 609-1631HD 609-1631 609-2031HD 609-2031 24 1.372 34.85 Standard 9-1437020-4 609-2431 26 1.472 37.39 34 1.872 47.55 40 2.172 55.17 50 2.672 67.87 Heavy Duty Standard Heavy Duty Standard Heavy Duty Standard Heavy Duty Standard 1-1437021-2 1-1437021-0 3-1437021-2 3-1437021-0 5-1437021-5 5-1437021-3 8-1437021-1 7-1437021-9 609-2631HD 609-2631 609-3431HD 609-3431 609-4031HD 609-4031 609-5031HD 609-5031 64 3.372 85.65 Heavy Duty 1-1437022-3 609-6431HD A Tyco Electronics T&B (Ref. Only) Note: Heavy duty part numbers are listed on Tyco Electronics customer drawing 3-1437020-7. Standard part numbers are listed on Tyco Electronics customer drawing 2-1437020-1. All part numbers are RoHS compliant. .570 [14.46] Heavy Duty Version 67 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Accessories (Continued) Strain Relief for AMPLATCH Novo and Ultra ATA Compliant Bus Connectors A No. of Pos. 10 14 Material and Finish Glass-filled polyester, black .240 [6.10] B Related Product Data AMP-LATCH Novo Connectors -- pages 48-51 Ultra ATA Compliant Bus Connectors -- pages 13-15 .186 [4.72] .106 [2.69] Ref. 16 20 24 .581 [14.76] Ref. 26 30 34 40 44 50 60 64 Dimensions A B .534 .690 13.56 17.53 .890 .734 22.61 18.64 .990 .834 25.15 21.18 1.034 1.190 26.26 30.23 1.390 1.234 31.34 35.31 1.490 1.334 37.85 33.88 1.534 1.690 38.96 42.93 1.734 1.890 44.04 48.01 2.190 2.034 55.63 51.66 2.390 2.234 60.71 56.74 2.534 2.690 64.36 68.33 3.034 3.190 77.06 81.03 3.390 3.234 86.11 82.14 Part Number 499252-5 499252-9 499252-8 499252-2 1-499252-0 499252-3 1-499252-2 499252-6 499252-1* 1-499252-1 499252-4 499252-7 1-499252-3 Accessories *Ultra ATA Compliant Strain Relief is 499252-1 only. Strain Relief for 2 mm Receptacle Connectors No. of Pos. 8 Material and Finish .015 Rad. Typ. [0.38] Glass-filled polyester, black B Typ. Related Product Data A 2 mm Receptacle Connectors -- pages 16 and 17 .130 [3.30] .132 [3.35] Typ. 10 12 .201 Typ. [5.11] 14 16 .276 [7.01] Typ. .056 Typ. [1.42] 20 .030 Typ. [0.76] .020 Typ. [0.51] .082 Typ. [2.08] .161 Typ. [4.09] 22 .139 Typ. [3.53] 24 .040 Typ. [1.02] 26 30 34 40 44 50 Dimensions A B .440 .314 11.18 7.98 .518 .392 13.16 9.96 .596 .470 15.14 11.94 .676 .550 17.17 13.97 .755 .629 19.18 15.98 .912 .786 23.16 19.96 .991 .865 25.17 21.97 1.070 .944 27.18 23.98 1.148 1.022 29.16 25.96 1.306 1.180 33.17 29.97 1.463 1.337 37.16 33.96 1.700 1.574 43.18 39.98 1.857 1.731 47.17 43.97 2.093 1.967 53.16 49.96 Part Number 1-111614-6 111614-1 1-111614-7 111614-2 111614-3 111614-4 1-111614-5 111614-5 111614-6 111614-7 111614-8 111614-9 1-111614-0 1-111614-1 Note: All part numbers are RoHS compliant. 68 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Accessories (Continued) Strain Relief for 622 and 636 Series Female Socket Connectors A Material and Finish Glass-filled PBT, see table for color .236 [6.00] Related Product Data Female Socket Connectors -- pages 52 and 53 .555 [14.10] Part Number Dimension C Color 6 .477 12.12 10 .677 17.20 14 .877 22.28 16 .977 24.82 20 1.177 29.90 24 1.377 34.98 26 1.477 37.52 30 1.677 42.60 34 1.877 47.68 40 2.177 55.30 50 2.677 68.00 Blue Black Blue Black Blue Black Blue Black Blue Black Blue Black Blue Black Blue Black Blue Black Blue Black Blue Black 2-1437023-9 1-1437026-9 4-1437023-7 3-1437026-9 7-1437023-1 6-1437026-6 8-1437023-9 8-1437026-5 1437024-5 1437027-7 1-1437024-6 5-1437011-3 2-1437024-8 3-1437027-4 4-1437024-0 6-1437011-6 5-1437024-3 8-1437027-0 8-1437024-3 3-1437028-4 1-1437025-2 6-1437028-8 T&B (Ref. Only) 622-0631 636-0631 622-1031 636-1031 622-1431 636-1431 622-1631 636-1631 622-2031 636-2031 622-2431 636-2431 622-2631 636-2631 622-3031 636-3031 622-3431 636-3431 622-4031 636-4031 622-5031 636-5031 60 3.177 80.70 Black 9-1437028-5 636-6031 3.377 85.78 Blue Black 4-1437025-0 1437029-2 622-6431 636-6431 64 Tyco Electronics Accessories No. of Pos. Note: These part numbers are listed on Tyco Electronics customer drawing 1-1437026-9. All part numbers are RoHS compliant. 69 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Ribbon Cable Assembly Machines (R-CAM) Product Facts I I I I Application Tooling I Terminates 28 AWG [0.08 mm2] .050 [1.27] centerline and 30 AWG [0.05 mm2] .025 [0.64] centerline cable to a variety of connectors Automatic in-process electrical testing -- tests all circuits for opens, shorts and high-voltage breakdown (up to 1,000 volts for receptacles, 800 volts for card edge connectors and 300 volts for .025 [0.64] centerline connectors); rejects cable assemblies failing any of these tests Operated by a user-friendly, interactive touchscreen -- or a keyboard on the R-CAM 4 Self-diagnostics shut down the machine when a malfunction occurs, pinpoint the malfunction, and identify it on the screen Produced under a Quality Management System certified to ISO 9001 A copy of the certificate is available upon request. ISO900e1d i rtif Ce The R-CAM 4, pictured above, is the newest fully automatic Ribbon Cable Assembly Machine for producing and testing daisy-chained ribbon cable assemblies. Enhancements of this model include the capability to process premanufactured slit-and-twist cable and the ability to produce assemblies with up to 10 connectors. The R-CAM 2A, 3A, and 4 terminate 28 AWG [0.08 mm2], .050 [1.27] centerline cable to a variety of connectors. The R-CAM 4 will also terminate 30 AWG [0.05 mm2] .025 [0.64] centerline cable. All of the R-CAM models automatically perform an in-process electrical test of all circuits for opens and shorts. In addition, all models automatically test the assembly for high-voltage breakdown up to 1,000 volts, depending on the machine and connector style. The purpose of this test is to detect gaps that may have been created during assembly that could eventually short out when in use. If an assembly fails any of these tests, the machine will shear the cable off at that point and automatically discard it into an alternate bin. 8 A, 50 or 60 Hz. Model 4 operates at 120 or 220 VAC, 50-60 Hz, single phase, 15A. These machines are programmed and operated with an interactive touchscreen that allows operators to access manual, set-up, run, and edit modes through easy-to-follow menu-driven prompts. Need more information? For more information, specifically about tooling, call Tyco Electronics at the numbers listed below. The R-CAM 2A and 3A require a minimum air supply of 80 psi [5.52 bar] at 8 scfm [0.0038m3/s]. The R-CAM 4 requires 80 psi [5.52 bar] at 12 scfm [0.0057 m3/s]. Self-diagnostics shut down the machine if a malfunction -- such as misloaded connectors or incorrectly fed cable -- is detected, pinpoint the malfunction, and identify it on the touchscreen. Models 2A and 3A are available in 120 or 220 VAC, 70 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Comparison of R-CAM 2A, R-CAM 3A and R-CAM 4 Machine Model R-CAM 2A R-CAM 3A R-CAM 4 Part Number* 760700-K 761900-K 318800-K Cable Size Cable Assembly Configurations (Refer to page 73) 28 AWG [0.08 mm2], .050 [1.27] centerline 28 AWG [0.08 mm2], .050 [1.27] centerline 28 AWG [0.08 mm2], .050 [1.27] centerline and 30 AWG [0.05 mm2], .025 [0.64] centerline Maximum cable length of 48 [1 220] Maximum cable length of 105 [2 665] Maximum cable length of 100 [2 540] Produces one- to four-connector assemblies with unterminated tail lengths up to 12 [305] Produces one- or two-connector assemblies with unterminated tail lengths up to 24 [610] Produces one- to 10-connector assemblies with unterminated tail lengths up to 24 [610] Trailing connectors can be oriented up or down Trailing connectors can be oriented up or down Trailing connectors can be oriented up or down Production Rates (Refer to page 72) Size Programmable Testing Changeover -- Automatically processes and tests assemblies produced with premanufactured slit-and-twist cable Depending on cable lengths, can apply and test up to 1 670 connectors per hour Depending on cable lengths, can apply and test up to 2 000 connectors per hour Depending on cable lengths, can apply and test up to 1 050 connectors per hour 108 [2 745] W x 54 [1 370] D x 60 [1 525] H; 750 lb [340 kg] 48 [1 220] W x 48 [1 220] D x 62 [1 575] H; 630 lb [286 kg] 68 [1 730] W x 58 [1 475] D x 72 [1 830] H; 1 300 lb [590 kg] Operated and programmed by a touchscreen Operated and programmed by a touchscreen Operated and programmed by a touchscreen or a keyboard Parameters for up to 130 cable assemblies can be retained in memory Parameters for up to 150 cable assemblies can be retained in memory Parameters for up to 1 000 cable assemblies can be retained in memory Another menu displays production totals or a log of the machine events Another menu displays production totals or a log of the machine events Automatically stops after each or three consecutive assemblies are rejected, as programmed by the operator Automatically stops when either a consecutive number of assemblies or a percentage of the batch run are rejected, as programmed by the operator Automatically stops each time a malfunction is detected Requires an average of 25 minutes, depending on assembly size Requires an average of 15 minutes, depending on assembly size Requires an average of 20 minutes to 1 hour, depending on assembly size and type Application Tooling -- -- *Note: Machine may require accessories. Before ordering, contact Tyco Electronics at the numbers listed below. 71 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Typical Production Rates (Assemblies/Hour) Machine Model Connectors Per Assembly 4 [100] Length 24 [160] 8 [205] 1 665 620 -- 570 500 405 2 R-CAM 2A 475 460 375 3 4 -- 420 360 R-CAM 3A 2 1 075 950 780 -- 275 265 4 -- 205 200 5 R-CAM 4 6 -- 170 165 10 -- -- -- Note: Actual production rates may vary depending on the cable assembly configuration. Available Tooling 48 [1 220] 100 [2 540] -- 300 280 255 660 255 190 160 115 -- -- -- -- 500 -- -- -- 105 Note: Call Tyco Electronics at the numbers listed below for part numbers or availability. Tooling for Connectors R-CAM 2A AMP-LATCH Ultra Novo Receptacles -- AMPLIMITE .050 Series Connectors Plugs AMPLIMITE HDF-20 D-Sub. 15, 25, 37 Receptacles .100 x .100 DIP Plugs One End Only, 20-64 Card Edge Connectors* AMP-LATCH Novo Receptacles* 2 mm Receptacles Universal I/O Pin Connectors Number of Positions R-CAM 3A -- -- 9, 15, 25, 37 One End Only, 10-64 20-64 10-64 20-64 -- One End Only, 20-64 10-64 12-50 -- R-CAM 4 ii -- 40 68 68 and 80 (Lead and Trail Modules) 68 and 80 (Lead Module Only) Available in future 20-50 (10-64 Available in future) 10-64 -- Trail Module Only * Supplied with the R-CAM 2A and R-CAM 3A only. Reel fed version. ii Order Connector Specific Tooling Packages / Feed Shear Tooling separately. Application Tooling i Products Applied AMPLIMITE HDF-20 D-Sub. Plugs AMPLIMITE HDF-20 D-Sub. Receptacles .100 x .100 DIP Plugs Card Edge Connectors AMP-LATCH Novo Receptacles 2 mm Receptacles Universal I/O Pin Connectors Pre-manufactured Slit-and-Twist Cable (R-CAM 4 only) Note: For more product information, call Tyco Electronics at the numbers listed below. 72 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Cable Assembly Configurations R-CAM 2A 2.70 to 8 [70 to 205] end-to-end 2.70 to 48 [70 to 1 220] end-to-end 0 to 8 [0 to 205] 1.50 Min. [35 Min.] center-to-center R-CAM 3A 1.74 to 105 [45 to 2 665] end-to-end 0 to 24 [0 to 610] Application Tooling 0 to 24 [0 to 610] 1.74 to 105 [45 to 2 665] end-to-end 1.74 to 105 [45 to 2 665] end-to-end R-CAM 4 1.60 to 100 [40 to 2 540] center-to-end 1.60 to 100 [40 to 2 540] center-to-center 0 to 24 [0 to 610] 1.60 Min. [40 Min.] center-to-center 1.25 Min. [30 Min.] center-to-center 3 Min. [75 Min.] center-to-center 73 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Application Tooling Manual Arbor Frame Assembly, Part No. 91085-2 Bench frame for applying a variety of IDC connectors, including AMPMODU MT and CHAMP. Features adjustable ram and handle, and a slide base. Tooling is mounted to the ram and into the tracks of the base plate. Hand Tool Kit--Part No. 768340-1 Terminating kit for .050 [1.27] centerline ribbon cable with 28 or 26 AWG [0.08 or 0.15 mm2] stranded or solid, or 30 AWG [0.05 mm2] solid conductors. Includes commercial grade hand tool with ratchet control for complete termination cycle, base assembly, bench-mount, tooling sets for standard and Novo receptacles, card edge connectors and D-Sub HDF low-profile connectors, and a carrying case. Application Tooling Tooling Instruction Sheets 408-7777--Manual Arbor Frame Assembly 408-6732--Pneumatic Auto-Cycle Assembly 408-9828--Hand Tool Kit 768340-1 for Connector-Specific Kits Pneumatic Auto-Cycle Unit, Part No. 91112-3 Pneumatic Foot Pedal Unit Part No. 91112-2 Basically an air-powered version of Manual Arbor Frame Assembly 91085-2. Features adjustable ram and cycle time, and automatic cycling when the lower assembly is slid into the frame to the rear of the base plate. Includes a guard around the frame opening. Foot pedal indicates cycle-- features adjustable ram and cycle time. 74 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Low Profile Headers Product Facts I I I I I I I I I Available in selected positions 10 thru 60 Flame retardant, thermoplastic housings, 94V-0 rated Vertical and right-angle versions available in double row configurations Available in .025 [0.64] square drawn wire posts Wash out clearance for flux removal Mates with Ribbon Cable Connectors Available with and without eject latches Available with and without "kinked" soldertails for PCB retention Performance Characteristics Headers are recognized under the Component Program of Underwriters Laboratories Inc. File No. E28476 I Headers are certified by Canadian Standards Association, File No. LR 7189 Product Specifications 108-40018 Electrical R I Technical Documents R Low Profile Headers Low profile IDC headers are recognized under the Component Program of Underwriters Laboratories Inc. File No. E60980, Vol. 5 Insulation Resistance -- 5,000 megohms minimum initial Dielectric Withstanding Voltage -- 1,000 V rms at sea level Current -- 1 ampere maximum per contact Operating Voltage -- 250 VAC Environmental Operating Temperature -- -65C to +105C R 75 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Low Profile Pin Headers, Center and Dual Polarized, .100 x .100 [2.54 x 2.54] Centerlines +.000 Low Profile Headers Vertical PCB Mount .025 [0.64] Square Post (Mating End) A -.010 [+0.00 -0.25] .045 [1.14] B Pin 1 .130 [3.30] .165 [4.19] .015 .010 0.38 0.25 [ ] .360 [9.14] .025 .001 [0.64 0.03] Typ. Material and Finish Housing -- Glass-filled nylon, UL 94V-0 rated, black Posts -- Brass, plated as follows: Plating A -- Duplex plated, gold flash over palladium-nickel, .000030 [0.00076] min. total on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel or .000030 [0.00076] min. gold on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel Plating B -- Duplex plated, gold flash over palladium-nickel, .000015 [0.00038] min. total on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel or .000015 [0.00038] min. gold on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel Pin 2 .025 .001 [0.64 0.03] .041 [1.04] .388 [9.86] .120 .015 [3.05 0.38] .240 [6.10] .185 .010 [4.70 0.25] .100 [2.54] .185 [4.70] Typ. .100 Typ. [2.54] .100 [2.54] Related Product Data Electrical Characteristics -- page 75 Mateable Connectors -- AMPMODU Wire-Applied Receptacles AMPMODU Board Mount Receptacles Short Point Wire-Applied Connectors AMP-LATCH Novo Receptacles and Female Socket Connectors, 609, 622 and 636 Series -- pages 48-55 .100 [2.54] .035 .003 [0.89 0.08] Dia. Typ. Recommended PC Board Hole Layout For Manual Insertion No. of Pos. 10 14 16 20 24 26 34 40 50 60 Dimensions A B .800 [20.32] .400 [10.16] 1.000 [25.40] .600 [15.24] 1.100 [27.94] .700 [17.78] 1.300 [33.02] .900 [22.86] 1.500 [38.10] 1.100 [27.94] 1.600 [40.64] 1.200 [30.48] 2.000 [50.80] 1.600 [40.64] 2.300 [58.42] 1.900 [48.26] 2.800 [71.12] 2.400 [60.96] 3.300 [83.82] 2.900 [73.66] Post Plating/Part Nos. Plating A Plating B 5103309-1 5103308-1 5103309-2 5103308-2 5103309-3 5103308-3 5103309-5 5103308-5 -- 1-5103308-3 5103309-6 5103308-6 5103309-7 5103308-7 5103309-8 5103308-8 1-5103309-0 1-5103308-0 -- 1-5103308-2 Note: All part numbers are RoHS compliant. 76 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Low Profile Pin Headers, Center and Dual Polarized, .100 x .100 [2.54 x 2.54] Centerlines (Continued) Low Profile Headers Right-Angle PCB Mount .025 [0.64] Square Post (Mating End) Position No.1 Indicator * .388 [9.86] .165 [4.19] .025 .001 [0.64 0.03] Typ. Material and Finish +.000 Housing -- Glass-filled nylon, UL 94V-0 rated, black Posts -- Brass, plated as follows: Plating A -- Duplex plated, gold flash over palladium-nickel, .000030 [0.00076] min. total on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel or .000030 [0.00076] min. gold on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel Plating B -- Duplex plated, gold flash over palladium-nickel, .000015 [0.00038] min. total on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel or .000015 [0.00038] min. gold on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel -.010 A +0.00 [-0.25] Pin 1 B .240 [6.09] .100 .130 Typ. [2.54] [3.31] .360 [9.14] .025 .001 [.635 0.03] Typ. .135+.020 -.010 [3.42+0.51 -0.25 ] .185 .010 [4.69 0.25] Typ. .185 Typ. [4.69] .015 .010 0.38 0.25 [ Pin 2 ] .123 [3.12] .100 [2.54] .100 Typ. [2.54] .100 [2.54] .035 .003 [0.89 0.08] Dia. Typ. Recommended PC Board Hole Layout For Manual Insertion Related Product Data Electrical Characteristics -- page 75 Mateable Connectors -- AMPMODU Wire-Applied Receptacles Short Point Wire-Applied Connectors AMP-LATCH Novo Receptacles and Female Socket Connectors, 609, 622 and 636 Series -- pages 48-55 Dimensions No. of Pos. 10 14 16 20 26 34 40 50 60 .800 1.000 1.100 1.300 1.600 2.000 2.300 2.800 3.300 A [20.32] [25.40] [27.94] [33.02] [40.64] [50.80] [58.42] [71.12] [83.82] .400 .600 .700 .900 1.200 1.600 1.900 2.400 2.900 B [10.16] [15.24] [17.78] [22.86] [30.48] [40.64] [48.26] [60.96] [73.66] Post Plating/Part Nos. Plating A Plating B 5103311-1 5103310-1 5103311-2 5103310-2 5103311-3 5103310-3 5103311-5 5103310-5 5103311-6 5103310-6 5103311-7 5103310-7 5103311-8 5103310-8 1-5103311-0 1-5103310-0 1-5103311-2 -- Note: All part numbers are RoHS compliant. 77 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Low Profile Headers Low Profile Pin Headers, Center and Dual Polarized, .100 x .100 [2.54 x 2.54] Centerlines & "Kinked" Solder Tails for PCB Retention Vertical PCB Mount .025 [0.64] Square Post (Mating End) with Board Retention Feature +.005 -.010 A +0.13 [-0.25] .045 [1.14] B Pin 1 .130 [3.30] .025 .020 0.64 0.51 .165 [4.19] [ ] .360 [9.14] Material and Finish Housing -- Glass-filled PPA, UL 94V-0 rated, black Posts -- Brass, plated as follows: Plating -- Duplex plated, gold flash over palladium-nickel, .000015 [0.00038] min. total on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel or .000015 [0.00038] min. gold on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel .100 [2.54] .025.001 [0.640.03] Typ. Pin 2 .025 .001 [0.64 0.03] .041 [1.04] .120 .015 [3.05 0.38] .388 [9.86] .240 [6.10] .100 [2.54] .185 [4.69] 2 Plcs. .185 2 Plcs. [4.69] Related Product Data .100 Typ. [2.54] Electrical Characteristics -- page 75 Mateable Connectors -- AMPMODU Wire-Applied Receptacles AMPMODU Board Mount Receptacles Short Point Wire-Applied Connectors AMP-LATCH Novo Receptacles and Female Socket Connectors, 609, 622 and 636 Series -- pages 48-55 .100 [2.54] .040 .003 [1.02 0.08] Dia. Typ. Recommended PC Board Hole Layout For Manual Insertion No. of Pos. 10 14 16 20 24 26 34 40 50 60 Dimensions A B .800 [20.32] .400 [10.16] 1.000 [25.40] .600 [15.24] 1.100 [27.94] .700 [17.78] 1.300 [33.02] .900 [22.86] 1.500 [38.10] 1.100 [27.94] 1.600 [40.64] 1.200 [30.48] 2.000 [50.80] 1.600 [40.64] 2.300 [58.42] 1.900 [48.26] 2.800 [71.12] 2.400 [60.96] 3.300 [83.82] 2.900 [73.66] Post Plating Part Nos. 5104338-1 5104338-2 5104338-3 5104338-4 5104338-5 5104338-6 5104338-7 5104338-8 5104338-9 1-5104338-0 Note: All part numbers are RoHS compliant. 78 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Low Profile Pin Headers, Center and Dual Polarized, .100 x .100 [2.54 x 2.54] Centerlines & "Kinked" Solder Tails for PCB Retention (Continued) Low Profile Headers Position No.1 Indicator Right-Angle PCB Mount .025 [0.64] Square Post (Mating End) with Board Retention Feature * .388 [9.86] .165 [4.19] .025.001 [0.640.03] Typ. +.005 -.010 A +0.13 Pin 1 [-0.25] .045 2 Plcs. [1.14] .130 Typ. [3.30] .100 [2.54] B Material and Finish Housing -- Glass-filled PPA, UL 94V-0 rated, black Posts -- Brass, plated as follows: Plating -- Duplex plated, gold flash over palladium-nickel, .000015 [0.00038] min. total on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel or .000015 [0.00038] min. gold on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel .360 [9.14] .240 [6.09] .025.001 [.6350.03] Typ. +.020 .125 -.010 +0.51 3.18 -0.25 [ .185 [4.69] 2 Plcs. .025 .020 0.64 0.51 ] [ ] .185 2 Plcs. [4.69] Pin 2 .123 [3.12] .100 [2.54] .100 [2.54] Typ. Related Product Data .100 [2.54] Electrical Characteristics -- page 75 Mateable Connectors -- AMPMODU Wire-Applied Receptacles Short Point Wire-Applied Connectors AMP-LATCH Novo Receptacles and Female Socket Connectors, 609, 622 and 636 Series -- pages 48-55 .040.003 [1.020.08] Dia. Typ. Recommended PC Board Hole Layout For Manual Insertion No. of Pos. 10 14 16 20 24 34 40 50 Dimensions A B .800 [20.32] .400 [10.16] 1.000 [25.40] .600 [15.24] 1.100 [27.94] .700 [17.78] 1.300 [33.02] .900 [22.86] 1.500 [38.10] 1.100 [27.94] 2.000 [50.80] 1.600 [40.64] 2.300 [58.42] 1.900 [48.26] 2.800 [71.12] 2.400 [60.96] Post Plating Part Nos. 5104340-1 5104340-2 5104340-3 5104340-4 5104340-5 5104340-7 5104340-8 5104340-9 Note: All part numbers are RoHS compliant. 79 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions IDC Low Profile Headers IDC Low Profile Ejection Style Pin Headers with Die Cast Ejection Latches, Military and Center Polarized, .100 x .100 [2.54 x 2.54] Centerlines Vertical PCB Mount .025 [0.64] Square Post (Mating End) B Pin 2 .362 [9.19] .254 .006 [6.45 0.15] .100 [2.54] Pin 1 Position #1 Indicator Material and Finish Housing -- Glass-filled PBT, UL 94V-0 rated, black Posts -- Brass or phosphor bronze, plated as follows: Plating -- Duplex plated, gold flash over palladium-nickel, .000030 [0.00076] min. total on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel or .000030 [0.00076] min. gold on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel .025 .001 [0.64 0.03] .025 .001 [0.64 0.03] .888 .012 [22.56 0.30] For Long Eject Latch .728 .012 [18.49 0.30] For Short Eject Latch Housing .404 .006 [10.26 0.15] .237 .007 [6.02 0.18] Post A O .031 Max. [0.79] .102 .015 [2.59 0.38] .100 [2.54] Related Product Data O .035 .003 [0.89 0.08] Electrical Characteristics -- page 75 Mateable Connectors -- AMP-LATCH Novo Receptacles and Female Socket Connectors, 609, 622 and 636 Series -- pages 48-55 Latching Height .575 Long [14.61] .427 Short [10.85] Latch .100 [2.54] Recommended PC Board Layout Dimensions A B No. of Pos. 10 14 16 20 24 26 30 34 40 50 60 .800 20.32 1.000 25.40 1.100 27.94 1.300 33.02 1.500 38.10 1.600 40.64 1.800 45.72 2.000 50.80 2.300 58.42 2.800 71.12 3.300 83.82 Part Numbers Pin Header with Short Latches Pin Header with Long Latches (Mates with Receptacles (Mates with Receptacles without Strain Relief) with Strain Relief) .400 10.16 .600 15.24 .700 17.78 .900 22.86 1.100 27.94 1.200 30.48 1.400 35.56 1.600 40.64 1.900 48.26 2.400 60.96 2.900 73.66 1761608-3 1761606-3 1761608-5 1761606-5 1761608-6 1761606-6 1761608-7 1761606-7 1761608-8 1761606-8 1761608-9 1761606-9 -- 1-1761606-0 1-1761608-1 1-1761606-1 1-1761608-3 1-1761606-3 1-1761608-5 1-1761606-5 1-1761608-6 1-1761606-6 Note: All part numbers are RoHS compliant. 80 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions IDC Low Profile Ejection Style Pin Headers with Die Cast Ejection Latches, Military and Center Polarized, .100 x .100 [2.54 x 2.54] Centerlines (Continued) IDC Low Profile Headers Right-Angle PCB Mount .025 [0.64] Square Post (Mating End) B Pin 2 .362 [9.19] .254 .006 [6.45 0.15] .100 [2.54] Pin 1 Latching Height .575 Long [14.61] .427 Short [10.85] .025 .001 [0.64 0.03] Position #1 Indicator Material and Finish Housing -- Glass-filled PBT, UL 94V-0 rated, black Posts -- Brass or phosphor bronze, plated as follows: Plating -- Duplex plated, gold flash over palladium-nickel, .000030 [0.00076] min. total on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel or .000030 [0.00076] min. gold on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel .025 .001 [0.64 0.03] .888 .012 [22.56 0.30] For Long Eject Latch Latch U .728 .012 [18.49 0.30] .404 .006 For Short [10.26 0.15] Eject Latch Housing Post U A .237 .007 [6.02 0.18] .100 [2.54] .102 .010 [2.59 0.25] Section U-U .030 [0.76] O .031 Max. [0.79] .100 [2.54] Related Product Data Electrical Characteristics -- page 75 O .035 .003 [0.89 0.08] Mateable Connectors -- AMP-LATCH Novo Receptacles and Female Socket Connectors, 609, 622 and 636 Series -- pages 48-55 .100 [2.54] Recommended PC Board Layout Dimensions A B No. of Pos. 10 14 16 20 26 34 40 50 60 .800 20.32 1.000 25.40 1.100 27.94 1.300 33.02 1.600 40.64 2.000 50.80 2.300 58.42 2.800 71.12 3.300 83.82 Part Numbers Pin Header with Short Latches Pin Header with Long Latches (Mates with Receptacles (Mates with Receptacles without Strain Relief) with Strain Relief) .400 10.16 .600 15.24 .700 17.78 .900 22.86 1.200 30.48 1.600 40.64 1.900 48.26 2.400 60.96 2.900 73.66 1761609-3 1761607-3 1761609-5 1761607-5 1761609-6 1761607-6 1761609-7 1761607-7 1761609-9 1761607-9 1-1761609-1 1-1761607-1 1-1761609-3 1-1761607-3 1-1761609-5 1-1761607-5 1-1761609-6 1-1761607-6 Note: All part numbers are RoHS compliant. 81 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions IDC Low Profile Ejection Style Pin Headers, Center Polarized, .100 x .100 [2.54 x 2.54] Centerlines .013 [0.33] IDC Low Profile Headers Vertical PCB Mount .025 [0.64] Square Post (Mating End) B Pin 2 .010 .252 +- .004 .005 .350 +- .010 + 0.25 + 0.13 [6.40 - 0.10 ] [8.89 - 0.25 ] .100 [2.54] Pin 1 A Material and Finish Housing and Eject Latches -- PBT, UL 94V-0 rated, blue Posts -- Phosphor bronze, plated as follows: Plating -- Duplex plated, .000030 [0.00076] min. gold on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel .350 [8.89] U .826 .020 Long [20.98 0.51] .665 .020 Short [16.89 0.51] .240 .010 [6.10 0.25] .013 [0.33] Position #1 Indicator .576 .006 Long [14.62 0.15] .419 .006 Short [10.64 0.15] U With Latches .025 .001 [0.63 0.03] .350 [8.89] Related Product Data .025 .001 [0.63 0.03] .025 .001 [0.63 0.03] Eject Latches Not Shown in Top and Side View for Clarity O .031 [0.79] Max. .015 C 0.38 [ ] Section U-U A U .013 [0.33] Electrical Characteristics -- page 75 Mateable Connectors -- AMP-LATCH Novo Receptacles and Female Socket Connectors, 609, 622 and 636 Series -- pages 48-55 Position #1 Indicator U Without Latches .100 [2.54] O .035 .003 [0.89 0.08] .100 [2.54] Recommended PC Board Layout Dim. C (Soldertail Length) .102 2.59 .165 4.19 Dimensions No. of Pos. A B 10 14 16 20 24 26 30 34 40 50 60 10 14 16 20 24 26 34 40 50 1.250 [31.75] 1.450 [36.83] 1.550 [39.37] 1.750 [44.45] 1.950[49.53] 2.050 [52.07] 2.250 [57.15] 2.450 [62.23] 2.750 [69.85] 3.250 [82.55] 3.750 [95.25] 1.250 [31.75] 1.450 [36.83] 1.550 [39.37] 1.750 [44.45] 1.950[49.53] 2.050 [52.07] 2.450 [62.23] 2.750 [69.85] 3.250 [82.55] .400 [10.16] .600 [15.24] .700 [17.78] .900 [22.86] 1.100 [27.94] 1.200 [30.48] 1.400 [35.56] 1.600 [40.64] 1.900 [48.26] 2.400 [60.96] 2.900 [73.66] .400 [10.16] .600 [15.24] .700 [17.78] .900 [22.86] 1.100 [27.94] 1.200 [30.48] 1.600 [40.64] 1.900 [48.26] 2.400 [60.96] Pin Header without Latches 1761693-3 -- -- -- 1761693-8 -- -- 1-1761693-1 -- -- 1-1761693-6 1761694-3 -- -- -- -- 1761694-9 -- -- -- Part Numbers Pin Header with Short Latches Pin Header with Long Latches (Mates with Receptacles (Mates with Receptacles without Strain Relief) with Strain Relief) 1761685-3 1761686-3 -- 1761686-5 1761685-6 1761686-6 1761685-7 1761686-7 1761685-8 1761686-8 1761685-9 1761686-9 1-1761685-0 -- 1-1761685-1 1-1761686-1 1-1761685-3 1-1761686-3 1-1761685-5 1-1761686-5 1-1761685-6 -- 1761687-3 -- -- -- -- -- 1761687-7 1761688-7 -- 1761688-8 1761687-9 1761688-9 1-1761687-1 1-1761688-1 1-1761687-3 -- -- 1-1761688-5 Note: All part numbers are RoHS compliant. 82 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions IDC Low Profile Ejection Style Pin Headers, Center Polarized, .100 x .100 [2.54 x 2.54] Centerlines (Continued) IDC Low Profile Headers Right-Angle PCB Mount .025 [0.64] Square Post (Mating End) B .013 [0.33] Pin 2 .010 .252 +- .004 0.25 [6.40 +- 0.10 ] .005 .350 +- .010 + 0.13 [8.89 - 0.25 ] .100 [2.54] Pin 1 A .025 .001 [0.63 0.03] Eject Latches Not Shown in Top and Side View for Clarity Material and Finish Housing and Eject Latches -- PBT, UL 94V-0 rated, blue Posts -- Phosphor bronze, plated as follows: Plating -- Duplex plated, .000030 [0.00076] min. gold on mating surfaces, .000100 [0.00254] min. tin on solder area, with entire post underplated .000050 [0.00127] min. nickel .350 [8.89] .025 .001 [0.63 0.03] .826 .020 [20.98 0.51] Long U .665 .020 [16.89 0.51] Short .013 [0.33] .015 C 0.38 [ ] Section U-U A .025 .001 [0.63 0.03] .100 [2.54] .576 .006 Long .240 .010 [6.10 0.25] [14.62 0.15] .419 .006 Short [10.64 0.15] U With Latches Position #1 Indicator .030 [0.76] O .031 [0.79] Max. U Related Product Data Electrical Characteristics -- page 75 Mateable Connectors -- AMP-LATCH Novo Receptacles and Female Socket Connectors, 609, 622 and 636 Series -- pages 48-55 .350 [8.89] .013 [0.33] U Without Latches Position #1 Indicator .100 [2.54] .100 [2.54] O .035 .003 [0.89 0.08] Recommended PC Board Layout Dim. C (Soldertail Length) .102 2.59 .165 4.19 Dimensions No. of Pos. A B 16 24 26 30 60 10 34 40 1.550 [39.37] 1.950[49.53] 2.050 [52.07] 2.250 [57.15] 3.750 [95.25] 1.250 [31.75] 2.450 [62.23] 2.750 [69.85] .700 [17.78] 1.100 [27.94] 1.200 [30.48] 1.400 [35.56] 2.900 [73.66] .400 [10.16] 1.600 [40.64] 1.900 [48.26] Part Numbers Pin Header with Long Latches (Mates with Receptacles with Strain Relief) 1761690-6 1761690-8 1761690-9 1-1761690-0 1-1761690-6 1761692-3 1-1761692-1 1-1761692-3 Note: All part numbers are RoHS compliant. 83 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Universal Ejection Style Pin Headers, Military, Center and Dual Polarized, .100 x .100 [2.54 x 2.54] Centerlines Vertical PCB Mount .025 [0.64] Sq. Posts (Mating End) .100 [2.54] Pin 2 .150 [3.81] .165 [4.19] .253 [6.43] .190 [4.83] .100 [2.54] .336 .315 [8.53] [8.00] .150 .050 [3.81] [1.27] A .107 [2.72] .025 [0.64] B Pin Header with Latches O .025 [0.64] .240 [6.10] Pin 1 .289 [7.34] C .110 or [2.79] .155 [3.94] Solder Tail Position No.1 Indicator .096 [2.44] Dia. 2 Plc. .025 [0.64] * Pin Header without Latches .106 [2.74] .549 [13.94] Material and Finish D Housing & Latches--Black PBT or nylon, UL 94V-0 rated Contacts -- Brass; duplex plated (See chart, page 85) .195 [4.95] Military, Center and Dual Polarized, Vertical Mount Universal Ejection Style Pin Headers Related Product Data Mateable Receptacles -- pages 48-55 Accessories -- Snap-In Polarizer -- page 63 No. of Positions 10 14 Technical Documents 16 Product Specifications 108-40018 Pin Headers 20 24 26 30 34 40 50 60 64 A .700 17.78 .900 22.86 1.000 25.40 1.200 30.48 1.400 35.56 1.500 38.10 1.700 43.18 1.900 48.26 2.200 55.88 2.700 68.58 3.200 81.28 3.400 86.36 B 1.100 27.94 1.300 33.02 1.400 35.56 1.600 40.64 1.800 45.72 1.900 48.26 2.100 53.34 2.300 58.42 2.600 66.04 3.100 78.74 3.600 91.44 3.800 96.52 Dimensions C D 1.260 .860 32.00 21.84 1.460 1.060 37.08 26.92 1.560 1.180 39.62 29.46 1.760 1.360 44.70 34.54 1.960 1.560 49.78 39.62 2.060 1.660 52.32 42.16 2.260 1.860 57.40 47.24 2.460 2.060 62.48 52.32 2.760 2.360 70.10 59.94 3.260 2.860 82.80 72.64 3.760 3.360 95.50 85.34 3.960 3.560 100.58 90.42 E 1.100 27.94 1.300 33.02 1.400 35.56 1.800 40.64 1.800 45.72 1.900 48.26 2.100 53.34 2.300 58.42 2.600 66.04 3.100 78.74 3.600 91.44 3.800 96.52 F .400 10.16 .600 15.24 .700 17.78 .900 22.86 1.100 27.94 1.200 30.48 1.400 35.56 1.600 40.64 1.900 48.26 2.400 60.98 2.900 73.66 3.100 78.74 Notes: 1. Pin headers in 10- and 14-position sizes have only one slot for snap-in polarizer (military polarization), located as shown. Notes: 2. Pin headers in 10-position size have only slot for dual polarization, located as shown. Notes: 3. For information regarding latch/pin header applications and for ordering latches separately, refer to page 96. 84 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Universal Ejection Style Pin Headers, Military, Center and Dual Polarized, .100 x .100 [2.54 x 2.54] Centerlines (Continued) Vertical PCB Mount .025 [0.64] Sq. Posts (Mating End) (Continued) Soldertail Length No. of Positions 10 14 16 20 24 26 .110 2.79 30 34 40 50 60 64 10 14 16 24 26 .155 3.94 30 34 40 50 60 64 Pin Header without Latches A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B 5102153-1 5102154-1 5102153-2 5102154-2 5102153-3 5102154-3 5102153-4 5102154-4 5102153-5 5102154-5 5102153-6 5102154-6 5102153-7 5102154-7 5102153-8 5102154-8 5102153-9 5102154-9 1-5102153-0 1-5102154-0 -- 1-5102154-1 1-5102153-2 1-5102154-2 5102155-1 5102156-1 -- 5102156-2 5102155-3 5102156-3 -- 5102156-4 -- 5102156-5 5102155-6 5102156-6 -- 5102156-7 5102155-8 5102156-8 5102155-9 5102156-9 1-5102155-0 1-5102156-0 -- 1-5102156-1 1-5102155-2 1-5102156-2 Pin Header w/ Short Latches (Mates with AMP-LATCH Receptacles without Strain Relief) 5499910-1 5499160-1 5499910-2 5499160-2 5499910-3 5499160-3 5499910-4 5499160-4 5499910-5 -- 5499910-6 5499160-6 5499910-7 -- 5499910-8 5499160-8 5499910-9 5499160-9 1-5499910-0 1-5499160-0 -- -- -- 1-5499160-2 -- 5499374-1 -- 5499374-2 -- -- -- 5499374-4 -- 5499374-5 -- 5499374-6 -- -- 5499911-8 5499374-8 5499911-9 5499374-9 -- 1-5499374-0 -- -- -- -- Pin Header w/ Long Latches (Mates with AMP-LATCH Receptacles with Strain Relief) 5499922-1 5499206-1 5499922-2 5499206-2 5499922-3 5499206-3 5499922-4 5499206-4 5499922-5 5499206-5 5499922-6 5499206-6 5499922-7 5499206-7 5499922-8 5499206-8 5499922-9 5499206-9 1-5499922-0 1-5499206-0 1-5499922-1 1-5499206-1 1-5499922-2 1-5499206-2 5499923-1 5102321-1 -- 5102321-2 5499923-3 5102321-3 5499923-4 5102321-4 5499923-5 5102321-5 5499923-6 5102321-6 5499923-7 5102321-7 5499923-8 5102321-8 5499923-9 5102321-9 1-5499923-0 1-5102321-0 1-5499923-1 1-5102321-1 1-5499923-2 1-5102321-2 Military, Center and Dual Polarized, Vertical Mount Universal Ejection Style Pin Headers 20 Contact Finish (Plating Code) Plating Code A -- Gold flash over palladium-nickel plate, .000015 [0.00038] min. total on the mating surfaces, .000100 [0.00254] min. tin plate on the soldertails, over .000050 [0.00127] min nickel underplate or .000015 [0.00038] min. gold on the mating surfaces, .000100 [0.00254] min. tin plate on the soldertails, over .000050 [0.00127] min. nickel underplate. Plating Code B -- Gold flash over palladium-nickel plate, .000030 [0.00076] min. total on the mating surfaces, .000100 [0.00254] min. tin plate on the soldertails, over .000050 [0.00127] min nickel underplate or .000030 [0.00076] min. gold on the mating surfaces, .000100 [0.00254] min. tin plate on the soldertails, over .000050 [0.00127] min. nickel underplate. Note: All part numbers are RoHS compliant. 85 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Universal Ejection Style Pin Headers, Military, Center and Dual Polarized, .100 x .100 [2.54 x 2.54] Centerlines (Continued) Mounting Information E 4-24 self-tapping screws and 2-56 bolts and nuts are available for mounting straight-thru pin headers of pc boards. Typical applications and part nos. for ordering this hardware are presented below. .106 [2.88] Dia. (For Nut & Bolt hardware) F .100 [2.54] .100 [2.54] .116 [2.95] Dia. (For Self-Tapping Screw hardware) .060 [1.52] .350 [8.89] Position No. 1 .035 [0.89] Dia. Recommended Mounting Hole Pattern For Vertical PCB Mount Headers PC board thicknesses are : .062 [1.57] for .110 [2.79] long posts, .125 [3.18] for .155 [3.94] long posts. Latch (See Note at left.) 2-56 Bolt & Nut (2 Each Req`d.) .256 [6.50] 4-24 Self-Tapping Screw (2 Req`d.) Military, Center and Dual Polarized, Vertical Mount Universal Ejection Style Pin Headers Note: 2-56 bolts and nuts may be used to mount pin headers with and without latches. If latches are to be used, the bolts must be positioned in the pin header before the latches are installed. Pin Header Mounting using 4-24 Self-Tapping Screws: Part No. 19156-1 (for .062 [1.57] Thick PC Board) Part No. 19156-2 (for .093 [2.36] Thick PC Board) Part No. 19156-3 (for .125 [3.18] Thick PC Board) Pin Header Mounting with 2-56 Bolts and Nuts: Part No. 746383-1 (Bolt Only) Kit No. 102198-1 (Bolt and Nut, 2 Each per Kit) Note: All part numbers are RoHS compliant. 86 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Universal Ejection Style Pin Headers with ACTION PIN Contacts, Military, Center and Dual Polarized, .100 x .100 [2.54 x 2.54] Centerlines Vertical PCB Mount .025 [0.64] Sq. Posts (Mating End) .100 [2.54] .150 [3.81] .253 [6.43] .165 [4.19] .190 [4.83] Pin 2 .336 .315 [8.53] [8.00] .050 .150 [3.81] [1.27] A B C Pin 1 .240 [6.10] .030 [0.76] Pin Header without Latches .025 [0.64] Material and Finish Housing -- Black PBT or nylon, UL 94V-0 rated Contacts--Copper alloy; duplex plated (See chart, page 88) .107 [2.72] .174 .610 Tail or [4.42] [15.49] Length .289 [7.34] .025 [0.64] Position No. 1 Indicator Related Product Data Mateable Receptacles -- pages 48-55 Accessories -- Snap-In Polarizer -- page 63 .549 [13.9] Technical Documents .025 [0.64] No. of Positions 10 14 16 20 24 26 30 34 40 50 60 64 A .700 17.78 .900 22.86 1.000 25.40 1.200 30.48 1.400 35.56 1.500 38.10 1.700 43.18 1.900 48.26 2.200 55.88 2.700 68.58 3.200 81.28 3.400 86.36 B 1.100 27.94 1.300 33.02 1.400 35.56 1.600 40.64 1.800 45.72 1.900 48.26 2.100 53.34 2.300 58.42 2.600 66.04 3.100 78.74 3.600 91.44 3.800 96.52 Dimensions C 1.260 32.00 1.460 37.08 1.560 39.62 1.760 44.70 1.960 49.78 2.060 52.32 2.260 57.40 2.460 62.48 2.760 70.10 3.260 82.80 3.760 95.50 3.960 100.58 D 1.100 27.94 1.300 33.02 1.400 35.56 1.600 40.64 1.800 45.72 1.900 48.26 2.100 53.34 2.300 58.42 2.600 66.04 3.100 78.74 3.600 91.44 3.800 96.52 E .400 10.16 .600 15.24 .700 17.78 .900 22.86 1.100 27.94 1.200 30.48 1.400 35.56 1.600 40.64 1.900 48.26 2.400 60.96 2.900 73.66 3.100 78.74 Military, Center and Dual Polarized Universal Ejection Style Pin Headers with ACTION PIN Contacts Product Specifications 108-40019 Pin Headers with ACTION PIN Contacts Application Specification 114-40020 AMP-LATCH Universal Headers with ACTION PIN Contacts Notes: 1. Pin headers in 10- and 14-position sizes have only one slot for snap-in polarizer (military polarization), located as shown. Notes: 2. Pin headers in 10-position size have only slot for dual polarization, located as shown. Notes: 3. For information regarding latch/pin header applications and for ordering latches separately, refer to page 96. 87 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Universal Ejection Style Pin Headers with ACTION PIN Contacts, Military, Center and Dual Polarized, .100 x .100 [2.54 x 2.54] Centerlines (Continued) Tail Length .174 [4.42] .610 [15.49] No. of Positions Pin Header (without Latches) 1658694-6 1658694-7 1658694-8 1658694-1 1658694-9 1658694-2 1-1658694-0 1-1658694-1 1658694-3 1658694-4 1658694-5 1658695-2 1658695-3 1658695-4 1658695-5 1658695-6 1658695-1 1658695-7 1658695-8 1658695-9 Contact Finish (Plating Code) 10 14 16 20 24 26 30 34 40 50 64 10 14 16 20 26 34 40 50 60 B B Military, Center and Dual Polarized Universal Ejection Style Pin Headers with ACTION PIN Contacts Plating Code B -- Gold flash over palladium-nickel plate, .000030 [0.00076] min. total on the mating surfaces, .000100 [0.00254] min. tin plate on the tails, over .000050 [0.00127] min nickel underplate or .000030 [0.00076] min. gold on the mating surfaces, .000100 [0.00254] min. tin plate on the tails, over .000050 [0.00127] min. nickel underplate. Mounting Information D 4-24 self-tapping screws and 2-56 bolts and nuts are available for mounting straight-thru pin headers of pc boards. Typical applications and part nos. for ordering this hardware are presented on page 86. E .106 [2.69]Dia. .100 [2.54] .100 [2.54] .060 [1.52] Position No. 1 .350 [8.89] * Recommended Mounting Hole Pattern For Vertical PCB Mount Header With ACTION PIN Contacts *For .080 [2.03] min. thick PCB refer to Application Specification 114-40020 for hole size and finish recommendations. Note: All part numbers are RoHS compliant. 88 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Universal Ejection Style Pin Headers, Military, Center and Dual Polarized, .100 x .100 [2.54 x 2.54] Centerlines Right-Angle PCB Mount .025 [0.64] Sq. Posts (Mating End) .100 [2.54] Pin 2 .150 [3.81] .253 [6.43] .165 [4.19] .190 [4.83] .336 .315 [8.53] [8.00] .050 [1.27] .150 [3.81] A B C Pin 1 .025 [0.64] Pos. No. 1 Indicator .096 [2.44] Pin Header with Latches .549 [13.94] .108 [2.74] .195 [4.95] D .025 [0.64] Dia. .100 [2.54] Pin Header without Latches .100 [2.54] .240 [6.10] .038 [0.97] .110 .155 [2.79] or [3.94] Typ. Typ. Solder Tail Material and Finish Housing & Latches -- Black PBT or nylon, UL 94V-0 rated Contacts -- Brass; duplex plated (See chart, page 90) Related Product Data No. of Positions 10 14 16 Technical Documents 20 Product Specifications 108-40018 Pin Headers 24 26 30 34 40 50 60 64 A .700 17.78 .900 22.86 1.000 25.40 1.200 30.48 1.400 35.56 1.500 38.10 1.700 43.18 1.900 48.26 2.200 55.88 2.700 68.58 3.200 81.28 3.400 86.36 .289 [7.34] B 1.100 27.94 1.300 33.02 1.400 35.56 1.600 40.64 1.800 45.72 1.900 48.26 2.100 53.34 2.300 58.42 2.600 66.04 3.100 78.74 3.600 91.44 3.800 96.52 Dimensions C D 1.260 .860 32.00 21.84 1.460 1.060 37.08 26.92 1.560 1.180 39.62 29.46 1.760 1.380 44.70 34.54 1.960 1.560 49.78 39.62 2.060 1.660 52.32 42.16 2.260 1.860 57.40 47.24 2.460 2.060 62.48 52.32 2.760 2.360 70.10 59.94 3.260 2.860 82.80 72.64 3.760 3.360 95.50 85.34 3.960 3.560 100.58 90.42 E .860 21.84 1.060 26.92 1.180 29.46 1.380 34.54 1.560 39.62 1.660 42.16 1.860 47.24 2.060 52.32 2.360 59.94 2.860 72.64 3.360 85.34 3.560 90.42 F .400 10.16 .600 15.24 .700 17.78 .900 22.86 1.100 27.94 1.200 30.48 1.400 35.56 1.600 40.64 1.900 48.26 2.400 60.98 2.900 73.66 3.100 78.74 Military, Center and Dual Polarized, Right-Angle Universal Ejection Style Pin Headers Mateable Receptacles -- pages 48-55 Accessories -- Snap-In Polarizer -- page 63 .025 .107 [0.64] [2.72] Notes: 1. Pin headers in 10- and 14-position sizes have only one slot for snap-in polarizer (military polarization), located as shown. Notes: 2. Pin headers in 10-position size have only slot for dual polarization, located as shown. 89 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Universal Ejection Style Pin Headers, Military, Center and Dual Polarized, .100 x .100 [2.54 x 2.54] Centerlines (Continued) Right-Angle PCB Mount .025 [0.64] Sq. Posts (Mating End) (Continued) Soldertail Length No. of Positions 10 14 16 20 24 26 .110 2.79 30 34 40 50 60 64 10 14 16 20 24 Military, Center and Dual Polarized, Right-Angle Universal Ejection Style Pin Headers 26 .155 3.94 30 34 40 50 60 64 Contact Finish (Plating Code) Pin Header without Latches A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B A B 5102159-1 5102160-1 5102159-2 -- 5102159-3 5102160-3 5102159-4 5102160-4 -- 5102160-5 5102159-6 5102160-6 5102159-7 -- 5102159-8 5102160-8 5102159-9 5102160-9 1-5102159-0 1-5102160-0 1-5102159-1 1-5102160-1 1-5102159-2 1-5102160-2 -- 5102162-1 5102161-2 5102162-2 -- -- 5102161-4 -- 5102161-5 5102162-5 -- -- 5102161-7 5102162-7 5102161-8 5102162-8 -- -- -- 1-5102162-0 -- 1-5102162-1 -- 1-5102162-2 Pin Header w/ Short Latches (Mates with Receptacles without Strain Relief) 5499913-1 5499345-1 5499913-2 5499345-2 5499913-3 -- 5499913-4 -- 5499913-5 5499345-5 5499913-6 -- 5499913-7 -- 5499913-8 -- 5499913-9 5499345-9 1-5499913-0 1-5499345-0 1-5499913-1 -- -- -- -- -- -- -- -- -- 5499914-4 -- -- -- -- -- -- -- 5499914-8 -- -- 5499376-9 -- -- -- -- -- -- Pin Header w/ Long Latches (Mates with Receptacles with Strain Relief) 5499786-1 5499141-1 5499786-2 5499141-2 -- 5499141-3 5499786-4 5499141-4 5499786-5 -- 5499786-6 5499141-6 -- 5499141-7 5499786-8 5499141-8 5499786-9 5499141-9 1-5499786-0 1-5499141-0 1-5499786-1 1-5499141-1 1-5499786-2 1-5499141-2 -- 5102322-1 5499925-2 5102322-2 -- 5102322-3 -- 5102322-4 5499925-5 5102322-5 -- 5102322-6 -- -- -- 5102322-8 -- -- 1-5499925-0 -- -- -- -- -- Plating Code A -- Gold flash over palladium-nickel plate, .000015 [0.00038] min. total on the mating surfaces, .000100 [0.00254] min. tin plate on the soldertails, over .000050 [0.00127] min nickel underplate or .000015 [0.00038] min. gold on the mating surfaces, .000100 [0.00254] min. tin plate on the soldertails, over .000050 [0.00127] min. nickel underplate. Plating Code B -- Gold flash over palladium-nickel plate, .000030 [0.00076] min. total on the mating surfaces, .000100 [0.00254] min. tin plate on the soldertails, over .000050 [0.00127] min nickel underplate or .000030 [0.00076] min. gold on the mating surfaces, .000100 [0.00254] min. tin plate on the soldertails, over .000050 [0.00127] min. nickel underplate. Note: All part numbers are RoHS compliant. 90 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Universal Ejection Style Pin Headers, Military, Center and Dual Polarized, .100 x .100 [2.54 x 2.54] Centerlines (Continued) Mounting Information No mounting hardware is supplied by Tyco Electronics. E .106 Dia. [2.69] F .100 [2.54] .100 [2.54] .029 [0.74] .230 [5.84] .035 Dia. Typ. [0.89] Position No.1 Recommended Mounting Hole Pattern For Right-Angle PCB Mount Headers PC board thicknesses are : .062 [1.57] for .110 [2.79] long posts, .125 [3.18] for .155 [3.94] long posts. Military, Center and Dual Polarized, Right-Angle Universal Ejection Style Pin Headers 91 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Universal Ejection Style Pinless Headers, Military, Center and Dual Polarized, .100 x .100 [2.54 x 2.54] Centerlines Vertical PCB Mount .025 [0.64] Sq. Posts (without latches) Pin 2 .100 [2.54] Dia. 2 Holes E .100 [2.54] .150 [3.81] .050 [1.27] C Pin 1 Position No.1 Indicator Pinless Header Material and Finish * Housing -- Black PBT or nylon, UL 94V-0 rated .549 [13.9] Related Product Data Mateable Receptacles -- pages 48-55 Accessories -- Snap-In Polarizer -- page 63 .315 [8.00] B A .096 [2.44] Dia. 2 Holes Technical Documents Product Specifications 108-40018 Pin Headers No. of Pos. 10 14 16 20 24 Military, Center and Dual Polarized Universal Ejection Style Pinless Headers 26 34 40 50 60 64 A 1.260 32.00 1.460 37.08 1.560 39.62 1.760 44.70 1.960 49.78 2.060 52.32 2.460 62.48 2.760 70.10 3.260 82.80 3.760 95.50 3.960 100.58 Dimensions B C .860 21.84 1.060 26.92 1.160 29.46 1.360 34.54 1.560 39.62 1.660 42.16 2.060 52.32 2.360 59.94 2.860 72.64 3.360 85.34 3.560 90.42 E 1.100 27.94 1.300 33.02 1.400 35.56 1.600 40.64 1.800 45.72 1.900 48.26 2.300 58.42 2.600 66.04 3.100 78.74 3.600 91.44 3.800 96.52 .400 10.16 .600 15.24 .700 17.78 .900 22.86 1.100 27.94 1.200 30.48 1.600 40.64 1.900 48.26 2.400 60.96 2.900 73.66 3.100 78.74 Pinless Header Part Nos. Press-Fit Clearance-Fit 499726-1 102142-6 -- 102142-8 -- 102142-9 -- 102142-1 -- 1-102142-0 -- 102142-2 499726-8 102142-3 499726-9 102142-4 1-499726-0 102142-5 1-499726-1 102142-7 1-499726-2 1-102142-3 Notes: 1. 10- and 14-position pinless headers have only one slot for snap-in polarizer (military polarization). 2. 10-position pinless headers have only one slot for dual polarization. 3. For information regarding latch/pin header applications and for ordering latches separately, refer to page 96. All part numbers are RoHS compliant. 92 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Universal Ejection Style Pinless Headers, Military, Center and Dual Polarized, .100 x .100 [2.54 x 2.54] Centerlines (Continued) Installation of Press-Fit Pinless Headers Insertion Instructions: 1. Place pinless header over preinstalled posts so that post tips start into header cavities. 2. With bottom of pc board supported, place steel block over header. Steel block must be wider and longer than header so that it covers all four sides of the header. However, for headers with latches pre-assembled, the steel block must not interfere with the latches. 3. Apply an even, centered force on steel block until header bottoms on pc board. If posts are longer than .545 [13.84], they may be forced against the steel block before the header is fully seated. In this situation, extreme caution must be taken so that posts are not damaged or pushed out of the pc board. FORCE FORCE Steel Block (Centered over Header) Pinless Header .025 Sq. Posts [0.64] Preinstalled in PC Board .529 [13.44] PC Board Insertion Force: 60 lb. [267 N] max. Retention Force: 20 lb. [89 N] min. Tyco Electronics recommends the use of a typical manual frame assembly for insertion of pinless headers. The frame assembly and steel block are not supplied by Tyco Electronics. Military, Center and Dual Polarized Universal Ejection Style Pinless Headers 93 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Universal Ejection Style Pin Headers with PCT Housing, .100 x .100 [2.54 x 2.54] Centerlines, .025 [0.64] Sq. Posts (Mating End) .100 x .100 [2.54 x 2.54], .025 [0.64] Sq. Posts (Mating End) Universal Ejection Style Pin Headers with PCT Housing C .195 [4.95] .200 [5.08] .549 [13.94] .110 [2.79] * .025 [0.64] Vertical PCB Mount .040 [1.02] Position No.1 Indicator A B Pin 1 D .250 [6.35] .289 [7.34] .150 [3.81] .050 [1.27] .100 [2.54] .100 [2.54] .100 [2.54] .150 [3.81] Material and Finish Housing -- Red PCT, UL 94V-0 rated Contacts -- Brass; Gold flash over palladium-nickel plate, .000030 [0.00076] min. total on the mating surfaces, .000100 [0.00254] min. tin plate on the soldertails, over .000050 [0.00127] min. nickel underplate or .000030 [0.00076] min. gold on the mating surfaces, .000100 [0.00254] min. tin plate on the soldertails, over .000050 [0.00127] min. nickel underplate .165 [4.19] .100 [2.54] O .025 [0.64] .129 [3.28] Pin 2 .350 [8.89] E Vertical C .200 [5.08] .040 [1.02] .195 [4.95] .549 [13.94] .110 Dia. [2.79] 2 Plc. .096 [2.44] * Mateable Receptacles -- pages 48-55 Accessories -- Snap-In Polarizer -- page 63 .110 [2.79] .315 .340 [8.00] [8.64] Right-Angle PCB Mount Related Product Data .240 [6.10] .025 [0.64] Position No.1 Indicator Technical Documents A Product Specifications 108-40018 Pin Headers Pin 1 B .250 [6.35] D .150 [3.81] .050 [1.27] .100 [2.54] .240 [6.10] .110 [2.79] .315 .340 [8.00] [8.64] .100 [2.54] .350 [8.89] .100 [2.54] .150 [3.81] .165 [4.19] E .129 [3.28] Pin 2 .289 [7.34] .151 [3.84] .100 [2.54] O .025 [0.64] Right-Angle 94 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Universal Ejection Style Pin Headers with PCT Housing, .100 x .100 [2.54 x 2.54] Centerlines, .025 [0.64] Sq. Posts (Mating End) (Continued) B 10 1.260 32.00 1.460 37.08 1.560 39.62 1.760 44.70 1.960 49.78 2.060 52.32 2.260 57.40 2.460 62.48 2.760 70.10 3.260 82.80 3.760 95.50 3.960 100.58 1.100 27.94 1.300 33.02 1.400 35.56 1.600 40.64 1.800 40.64 1.900 48.26 2.100 53.34 2.300 58.42 2.600 66.04 3.100 78.74 3.600 91.44 3.800 96.52 .860 21.84 1.060 26.92 1.160 29.46 1.360 34.54 1.560 39.62 1.660 42.16 1.860 47.24 2.060 52.32 2.360 59.94 2.860 72.64 3.360 85.34 3.560 90.42 14 16 20 24 26 30 34 40 50 60 64 D E .700 17.78 .900 22.86 1.000 25.40 1.200 30.48 1.400 35.56 1.500 38.10 1.700 43.18 1.900 48.26 2.200 55.88 2.700 68.58 3.200 81.28 3.400 86.36 .400 10.16 .600 15.24 .700 17.78 .900 22.86 1.100 27.94 1.200 30.48 1.400 35.56 1.600 40.64 1.900 48.26 2.400 60.98 2.900 73.66 3.100 78.74 Part Numbers Vertical Right-Angle Pin Header Pin Header (without (without Latches) Latches) .100 x .100 [2.54 x 2.54], .025 [0.64] Sq. Posts (Mating End) Universal Ejection Style Pin Headers with PCT Housing A Dimensions C No. of Pos. -- 5111008-1 -- 5111105-2 -- 5111105-3 -- 5111105-4 5111105-5 5111008-5 5111105-6 -- 5111008-7 5111105-7 5111008-8 5111105-8 5111008-9 5111105-9 1-5111008-0 1-5111105-0 1-5111008-1 1-5111105-1 1-5111008-2 1-5111105-2 Note: All part numbers are RoHS compliant. .106 Dia. [2.69] Dia. Typ. Position No. 1 .100 [2.54] CL of Holes B .100 [2.54] Typ. .070 [1.78] Typ. .060 [1.52] CL of Holes .090 [2.29] .110 [2.79] of Stencil Pattern .035 [0.89] After Plating Recommended PC Board Mounting Pattern for Vertical Header Position No. 1 C .100 [2.54] CL of Holes .100 [2.54] Typ. .029 [.736] CL of Holes .475 Max.* [12.07] .106 Dia. [2.69] Dia. Typ. .070 [1.78] Typ. .090 [2.29] .035 [0.89] After Plating .110 [2.79] of Stencil Pattern Board Edge Recommended Pc Board Mounting Pattern for Right-Angle Header *Max. distance from edge of PC board for daisy chain applications 95 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Latches for Ejection Style Universal Pin Headers and Pinless Headers Latches for Ejection Style Pin Headers and Pinless Headers Latches for use with AMP-LATCH Novo Receptacles and Female Socket Connectors, 609, 622 & 636 Series Latch/Pin Header Applications 1.092 1.075 [27.72] [27.31] Material Red PCT, UL 94V-0 Rated .265 [6.73] .576 [14.63] Figure 1 -- Use Long Latch for AMP-LATCH Novo Receptacles with Strain Relief & Female Socket Connectors with Strain Relief Long Latch Part No. 111338-1 (See Figure 1) .895 [22.73] .416 [10.57] .175 [4.45] Short Latch Part No. 111293-1 (See Figure 2) Figure 2 -- Use Short Latch for AMP-LATCH Novo Receptacles without Strain Relief & Female Socket Connectors without Strain Relief Material Material Black thermoplastic, UL 94V-0 Rated Black thermoplastic, UL 94V-0 Rated .576 [14.63] .561 [14.25] .475 [12.07] .185 Ref. [4.70] .691 Ref. [17.55] Long Latch Part No. 102320-1 (See Figure 1) .416 [10.57] .140 .008 [3.56 0.20] Special Long Latch Part No. 1825851-1 for AMPMODU Mod IV Housing with Center Polarization Key Short Latch Part No. 102312-1 (See Figure 2) Note: All part numbers are RoHS compliant. 96 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Cable Solutions .100 [2.54] Centerline, IDC Ribbon Cable, PVC Insulation Product Specifications Voltage Rating -- 300 Volts UL Recognized -- AWM Style 2651 CSA -- Available on request B A Cable Solutions .050 Typ. [1.27] C Edge Mark Dimensions A B 24 AWG 7/32 Tinned Copper 2 .100 [2.54] .200 [5.08] 5 .400 [10.16] .500 [12.70] 10 .900 [22.86] 1.000 [25.40] 15 1.400 [35.56] 1.500 [38.10] 20 1.900 [48.26] 2.000 [50.80] 25 2.400 [60.96] 2.500 [63.50] 28 2.700 [68.58] 2.800 [71.12] 26 AWG 7/34 Tinned Copper 2 .100 [2.54] .200 [5.08] 5 .400 [10.16] .500 [12.70] 10 .900 [22.86] 1.000 [25.40] 15 1.400 [35.56] 1.500 [38.10] 20 1.900 [48.26] 2.000 [50.80] 25 2.400 [60.96] 2.500 [63.50] 28 2.700 [68.58] 2.800 [71.12] 26 AWG 7/34 Overcoated Tinned Copper 2 .100 [2.54] .200 [5.08] 5 .400 [10.16] .500 [12.70] 10 .900 [22.86] 1.000 [25.40] 15 1.400 [35.56] 1.500 [38.10] 20 1.900 [48.26] 2.000 [50.80] 25 2.400 [60.96] 2.500 [63.50] 28 2.700 [68.58] 2.800 [71.12] No. of Conductors C .010 [0.25] .100 [2.54] Typ. Part Number .044 .044 .044 .044 .044 .044 .044 [1.12] [1.12] [1.12] [1.12] [1.12] [1.12] [1.12] 57746-2 57746-5 1-57746-0 1-57746-5 2-57746-0 2-57746-5 2-57746-8 .039 .039 .039 .039 .039 .039 .039 [0.99] [0.99] [0.99] [0.99] [0.99] [0.99] [0.99] 57744-2 57744-5 1-57744-0 1-57744-5 2-57744-0 2-57744-5 2-57744-8 .039 .039 .039 .039 .039 .039 .039 [0.99] [0.99] [0.99] [0.99] [0.99] [0.99] [0.99] 57745-2 57745-5 1-57745-0 1-57745-5 2-57745-0 2-57745-5 2-57745-8 Insulation -- Gray Flame Retardant Flexible PVC .007 [0.17] Minimum Insulation Thickness Temperature Rating -- -20C to +105C Flammability -- UL: VW1 Dimensions A B 24 AWG 7/32 Overcoated Tinned Copper 2 .100 [2.54] .200 [5.08] 5 .400 [10.16] .500 [12.70] 10 .900 [22.86] 1.000 [25.40] 15 1.400 [35.56] 1.500 [38.10] 20 1.900 [48.26] 2.000 [50.80] 25 2.400 [60.96] 2.500 [63.50] 28 2.700 [68.58] 2.800 [71.12] 22 AWG 7/30 Tinned Copper 2 .100 [2.54] .200 [5.08] 5 .400 [10.16] .500 [12.70] 10 .900 [22.86] 1.000 [25.40] 15 1.400 [35.56] 1.500 [38.10] 20 1.900 [48.26] 2.000 [50.80] 25 2.400 [60.96] 2.500 [63.50] 28 2.700 [68.58] 2.800 [71.12] No. of Conductors C Part Number .044 .044 .044 .044 .044 .044 .044 [1.12] [1.12] [1.12] [1.12] [1.12] [1.12] [1.12] 57747-2 57747-5 1-57747-0 1-57747-5 2-57747-0 2-57747-5 2-57747-8 .051 .051 .051 .051 .051 .051 .051 [1.30] [1.30] [1.30] [1.30] [1.30] [1.30] [1.30] 57748-2 57748-5 1-57748-0 1-57748-5 2-57748-0 2-57748-5 2-57748-8 Other Conductor Counts Available on Request. Contact MADISON CABLE (1-877-MADISON), a Division of Tyco Electronics Corporation, for engineering questions or for order placement of this cable. 97 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Cable Solutions (Continued) .156 [3.96] Centerline, Flat Ribbon Cable, PVC Insulation Product Specifications Cable Solutions Voltage Rating -- 300 Volts UL Recognized -- AWM Style 2651 CSA -- Available on request B A .078 Typ. [1.98] C Edge Mark No. of Conductors .010 [0.25] .156 [3.96] Typ. A 22 AWG 7/30 Tinned Copper 2 .156 [3.96] 5 .624 [15.85] 10 1.404 [35.66] 15 2.184 [55.47] 20 2.964 [75.29] 24 3.588 [91.14] 18 AWG 7/26 Tinned Copper 2 .156 [3.96] 5 .624 [15.85] 10 1.404 [35.66] 15 2.184 [55.47] 20 2.964 [75.29] 24 3.588 [91.14] Insulation -- Gray Flame Retardant Flexible PVC .007 [0.17] Minimum Insulation Thickness Temperature Rating -- -20C to +105C Flammability -- UL: VW1 Dimensions B C Part Number .312 .780 1.560 2.340 3.120 3.744 [7.92] [19.81] [39.62] [59.44] [79.25] [95.10] .051 .051 .051 .051 .051 .051 [1.30] [1.30] [1.30] [1.30] [1.30] [1.30] 57750-2 57750-5 1-57750-0 1-57750-5 2-57750-0 2-57750-4 .312 .780 1.560 2.340 3.120 3.744 [7.92] [19.81] [39.62] [59.44] [79.25] [95.10] .068 .068 .068 .068 .068 .068 [1.73] [1.73] [1.73] [1.73] [1.73] [1.73] 57752-2 57752-5 1-57752-0 1-57752-5 2-57752-0 2-57752-4 Other Conductor Counts Available on Request. Contact MADISON CABLE (1-877-MADISON), a Division of Tyco Electronics Corporation, for engineering questions or for order placement of this cable. 98 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Part Number Index (Continued) Note: This index lists all cataloged parts by base no. only. Complete part nos. (with prefixes and/or suffixes) are shown on the page(s) indicated. Part No. 19156 57034 57040 57744 57745 57746 57747 57748 57750 57752 91085 91112 91295 100411 102142 102198 102312 102320 104068 104069 104072 104652 104655 104656 104693 104891 104892 104893 104894 104895 111196 111293 111338 111382 111446 111451 111492 111494 111504 111506 111547 111614 111620 111623 111626 120623 147121 147381 147382 147383 147384 147413 147503 174638 174903 175629 175637 188275 188431 215079 215083 Page 86 47 47 97 97 97 97 97 98 98 42, 74 42, 74 28, 29 41 92 86 96 96 9, 10 9, 11 65 20 21 21 21 27 26 26 24 24 9 96 96 58 45 63 45 46 45 46 67 68 64 17 17 63 21 21 21 21 20 20 21 62 62 62 62 32, 33, 36, 40, 41 41 32, 33, 34, 38, 40 32, 33, 38, 41 Page Part No. 215460 32, 33, 35, 38, 40, 41 215464 32, 33, 37, 41 215570 32, 33, 39 41 338068 41 338069 338070 41 32, 33, 40, 41 338095 32, 33, 40, 42 338096 338097 32, 33, 40, 42 338728 41 14, 49, 50, 51, 68 499252 65 499712 499726 92 499991 63 28, 29 543518 677410 43 677412 43 43 677463 42 677499 677894 42 677895 42 42 733278 733280 42 734024 42 734155 42 734870 42 746383 86 746603 47 746610 58 746611 59 768340 74 1377074 44 1437006 56 1437011 69 1437020 67 1437021 67 1437022 67 1437023 64, 69 1437024 69 1437025 69 1437026 69 1437027 69 1437028 69 1437029 69 1499252 68 1658525 57 1658526 55 1658527 53 1658528 53 1658618 14 1658619 14 1658620 49 1658621 50 1658622 50 1658623 49 1658624 51 1658694 88 1658695 88 1734161 15 1734162 15 1761606 80 Part No. 1761607 1761608 1761609 1761685 1761686 1761687 1761688 1761690 1761692 1761693 1761694 1825851 1888188 5088450 5102153 5102154 5102155 5102156 5102159 5102160 5102161 5102162 5102321 5102322 5103308 5103309 5103310 5103311 5104338 5104340 5111008 5111105 5111448 5111595 5111824 5499141 5499160 5499206 5499345 5499374 5499376 5499786 5499910 5499911 5499913 5499914 5499922 5499923 5499925 5746612 5746613 5746615 6437006 6489700 Page 81 80 81 82 82 82 82 83 83 82 82 96 15 66 85 85 85 85 90 90 90 90 85 90 76 76 77 77 78 79 95 95 46 12 15 90 85 85 90 85 90 90 85 85 90 90 85 85 90 59 59 60 61 15 99 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Engineering Notes 100 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Engineering Notes 101 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Ribbon Cable Interconnect Solutions Engineering Notes 102 Catalog 82012 Revised 10-09 www.tycoelectronics.com Dimensions are in inches and millimeters unless otherwise specified. Values in brackets are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA: 1-800-522-6752 Canada: 1-905-470-4425 Mexico: 01-800-733-8926 C. America: 52-55-1106-0803 South America: 55-11-2103-6000 Hong Kong: 852-2735-1628 Japan: 81-44-844-8013 UK: 44-8706-080-208 Global Contacts Americas Argentina - Buenos Aires Phone: +54-11-4733-2200 Fax: +54-11-4733-2211 Brasil - Sao Paulo Phone: +55-11-2103-6000 +55-11-2103-6030 Fax: Canada - Toronto Phone: +905-475-6222 +905-474-5520 Fax: Product Information Center: Phone: +905-470-4425 +905-474-5525 Fax: Chile - Santiago Phone: +56-2-345-0361 +56-2-223-1477 Fax: Colombia - Bogota Phone: +57-1-319-8959 Fax: +57-1-319-8960 Mexico - Mexico City Phone: +52-55-1106-0800 +01-800-733-8926 Fax: +52-55-1106-0901 For Latin/South American Countries not shown Phone: +54-11-4733-2015 Fax: +54-11-4733-2083 United States Harrisburg, PA Phone: +1-717-564-0100 Fax: +1-717-986-7575 Product Information Center: Phone: +1-800-522-6752 Fax: +1-717-986-7575 Troy, MI Phone: +1-248-273-3359 +1-248-273-3322 Fax: Asia/ Pacific Australia - Sydney Phone: +61-2-9554-2600 Fax: +61-2-9502-2556 Product Information Center: Phone: +61-2-9840-8200 Fax: +61-2-9634-6188 Japan - Kawasaki, Kanagawa Phone: +81-44-844-8111 Fax: +81-44-812-3207 Product Information Center: Phone: +81-44-844-8013 Fax: +81-44-812-3200 India - Bangalore Phone: +91-80-285-40800 Fax: +91-80-285-40820 Korea - Seoul Phone: +82-2-3415-4500 Fax: +82-2-3486-3810 Indonesia - Jakarta Phone: +65-6482-0311 Fax: +65-6482-1012 Malaysia - Selangor Phone: +60-3-7805-3055 Fax: +60-3-7805-3066 New Zealand - Auckland Phone: +64-9-634-4580 Fax: +64-9-634-4586 Singapore - Singapore Phone: +65-6482-0311 Fax: +65-6482-1012 Philippines - Makati City Phone: +632-848-0171 +632-867-8661 Fax: Taiwan - Taipei Phone: +886-2-8768-2788 +886-2-8768-2268 Fax: People's Republic of China Hong Kong Phone: +852-2735-1628 +852-2735-0243 Fax: Thailand - Bangkok Phone: +66-2-955-0500 Fax: +66-2-955-0505 Shanghai Phone: +86-21-2407-1588 Fax: +86-21-2407-1599 Vietnam - Ho Chi Minh City Phone: +84-8-930-5546 Fax: +84-8-930-3443 Europe/ Middle East /Africa Austria - Vienna Phone: +43-1-905-60-0 Fax: +43-1-905-60-1333 Product Information Center: Phone: +43-1-905-60-1249 Fax: +43-1-905-60-1251 France - Cergy-Pontoise Cedex Phone: +33-1-3420-8888 Fax: +33-1-3420-8600 Product Information Center: Phone: +33-1-3420-8686 Fax: +33-1-3420-8623 Belarus - Minsk Phone: +375 17 237 47 94 Fax: +375 17 237 47 94 France Export Divisions - Cergy-Pontoise Cedex Phone: +33-1-3420-8804 Fax: +33-1-3420-8699 Belgium - Kessel-Lo Phone: +32-16-352-300 Fax: +32-16-352-355 Bulgaria - Sofia Phone: +359-2-971-2152 Fax: +359-2-971-2153 Czech Republic and Slovakia Czech Republic - Kurim Phone: +420-541-162-111 Fax: +420-541-162-223 Product Information Center: Phone: +420-541-162-113 Fax: +420-541-162-132 Denmark - Glostrup Phone: +45-43-48-04-00 Fax: +45-43-44-14-14 Egypt - Cairo Phone: +202-419-2334 Fax: +202-417-7647 Estonia - Tartu Phone: +372-5138-274 Fax: +372-7400-779 Finland - Helsinki Phone: +358-95-12-34-20 Fax: +358-95-12-34-250 82012-2.5M--CIS--FP--10-09 Printed in the U.S.A. Germany - Bensheim Phone: +49-6251-133-0 Fax: +49-6251-133-1600 Product Information Center: Phone: +49-6251-133-1999 Fax: +49-6251-133-1988 Greece - Athens Phone: +30-210-9370396/397 Fax: +30-210-9370-655 Hungary - Budapest Phone: +36-1-289-1000 Fax: +36-1-289-1010 Product Information Center: Phone: +36-1-289-1016 Fax: +36-1-289-1017 Ireland - Dublin Phone: +353-1-866-5612 Fax: +353-1-866-5714 Israel - Petach-Tikva Phone: +972-3-929-0999 Fax: +972-3-919-1088 Italy - Collegno (Torino) Phone: +39-011-4012-111 Fax: +39-011-4031-116 Product Information Center: Phone: +39-011-4012-428 Fax: +39-011-40-287-428 Lithuania and Latvia Lithuania - Vilnius Phone: +370-5-213-1402 Fax: +370-5-213-1403 Product Information Center: Phone: +370-5-211-3016 Fax: +370-5-213-1403 Netherlands - 'sHertogenbosch Phone: +31-73-6246-246 Fax: +31-73-6212-365 Product Information Center: Phone: +31-73-6246-999 Fax: +31-73-6246-998 Norway - Nesbru Phone: +47-66-77-88-50 Fax: +47-66-77-88-55 Poland - Warsaw Phone: +48-22-4576-700 Fax: +48-22-4576-720 Product Information Center: Phone: +48-22-4576-704 Fax: +48-22-4576-720 Romania - Bucharest Phone: +40-21-311-3479/3596 Fax: +40-21-312-0574 Russia - Moscow Phone: +7-495-790-7902 Fax: +7-495-721-1893 Product Information Center: Phone: +7-495-790-7902-404 Fax: +7-495-790-7902-401 Russia - St. Petersburg Phone: +7-812-718-8192 Fax: +7-812-718-8193 Slovenia - Ljubljana Phone: +386-1561-3270 Fax: +386-1561-3240 South Africa - Port Elizabeth Phone: +27-41-503-4500 Fax: +27-41-581-0440 Spain - Barcelona Phone: +34-93-291-0330 Fax: +34-93-201-7879 Sweden - Upplands Vasby Phone: +46-8-50-72-50-00 Fax: +46-8-50-72-50-01 Switzerland - Steinach Phone: +41-71-447-0447 Fax: +41-71-447-0444 Turkey - Istanbul Phone: +90-212-281-8181/2/3 +90-212-2825130/5430 Fax: +90-212-281-8184 Ukraine - Kiev Phone: +380-44-206-2265 Fax: +380-44-206-2264 Product Information Center: Phone: +380-44-206-2265 Fax: +380-44-206-2264 United Kingdom - Stanmore, Middlesex Phone: +44-8706-080208 Fax: +44-208-954-6234 Product Information Center: Freephone (UK only): +0800-267-666 Phone: +44-8706-080208 Fax: +44-208-420-8095 Tyco Electronics Corporation www.tycoelectronics.com Catalog 82012 Revised 10-09 TE (logo) and Tyco Electronics are trademarks of the Tyco Electronics group of companies and its licensors. tycoelectronics.com 82012-2.5M-CIS-FP-10-09 Ribbon Cable Interconnect Solutions Tyco Electronics Corporation Harrisburg, PA Ribbon Cable Interconnect Solutions