MC9S08DZ60 MC9S08DZ48 MC9S08DZ32 MC9S08DZ16 Data Sheet HCS08 Microcontrollers MC9S08DZ60 Rev. 4 6/2008 freescale.com MC9S08DZ60 Series Features 8-Bit HCS08 Central Processor Unit (CPU) * 40-MHz HCS08 CPU (20-MHz bus) * HC08 instruction set with added BGND instruction * Support for up to 32 interrupt/reset sources On-Chip Memory * Flash read/program/erase over full operating voltage and temperature -- MC9S08DZ60 = 60K -- MC9S08DZ48 = 48K -- MC9S08DZ32 = 32K -- MC9S08DZ16 = 16K * Up to 2K EEPROM in-circuit programmable memory; 8-byte single-page or 4-byte dual-page erase sector; Program and Erase while executing Flash; Erase abort * Up to 4K random-access memory (RAM) Power-Saving Modes * Two very low power stop modes * Reduced power wait mode * Very low power real time interrupt for use in run, wait, and stop Clock Source Options * Oscillator (XOSC) -- Loop-control Pierce oscillator; Crystal or ceramic resonator range of 31.25 kHz to 38.4 kHz or 1 MHz to 16 MHz * Multi-purpose Clock Generator (MCG) -- PLL and FLL modes (FLL capable of 1.5% deviation using internal temperature compensation); Internal reference clock with trim adjustment (trimmed at factory, with trim value stored in flash); External reference with oscillator/resonator options System Protection * Watchdog computer operating properly (COP) reset with option to run from backup dedicated 1-kHz internal clock source or bus clock * Low-voltage detection with reset or interrupt; selectable trip points * Illegal opcode detection with reset * Illegal address detection with reset * Flash block protect * Loss-of-lock protection Development Support * Single-wire background debug interface * On-chip, in-circuit emulation (ICE) with real-time bus capture Peripherals * ADC -- 24-channel, 12-bit resolution, 2.5 s conversion time, automatic compare function, temperature sensor, internal bandgap reference channel * ACMPx -- Two analog comparators with selectable interrupt on rising, falling, or either edge of comparator output; compare option to fixed internal bandgap reference voltage * MSCAN -- CAN protocol - Version 2.0 A, B; standard and extended data frames; Support for remote frames; Five receive buffers with FIFO storage scheme; Flexible identifier acceptance filters programmable as: 2 x 32-bit, 4 x 16-bit, or 8 x 8-bit * SCIx -- Two SCIs supporting LIN 2.0 Protocol and SAE J2602 protocols; Full duplex non-return to zero (NRZ); Master extended break generation; Slave extended break detection; Wakeup on active edge * SPI -- Full-duplex or single-wire bidirectional; Double-buffered transmit and receive; Master or Slave mode; MSB-first or LSB-first shifting * IIC -- Up to 100 kbps with maximum bus loading; Multi-master operation; Programmable slave address; General Call Address; Interrupt driven byte-by-byte data transfer * TPMx -- One 6-channel (TPM1) and one 2-channel (TPM2); Selectable input capture, output compare, or buffered edge-aligned PWM on each channel * RTC -- (Real-time counter) 8-bit modulus counter with binary or decimal based prescaler; Real-time clock capabilities using external crystal and RTC for precise time base, time-of-day, calendar or task scheduling functions; Free running on-chip low power oscillator (1 kHz) for cyclic wake-up without external components Input/Output * 53 general-purpose input/output (I/O) pins and 1 input-only pin * 24 interrupt pins with selectable polarity on each pin * Hysteresis and configurable pull device on all input pins. * Configurable slew rate and drive strength on all output pins. Package Options * 64-pin low-profile quad flat-pack (LQFP) -- 10x10 mm * 48-pin low-profile quad flat-pack (LQFP) -- 7x7 mm * 32-pin low-profile quad flat-pack (LQFP) -- 7x7 mm MC9S08DZ60 Data Sheet Covers MC9S08DZ60 MC9S08DZ48 MC9S08DZ32 MC9S08DZ16 MC9S08DZ60 Rev. 4 6/2008 FreescaleTM and the Freescale logo are trademarks of Freescale Semiconductor, Inc. (c) Freescale Semiconductor, Inc., 2007-2008. All rights reserved. Revision History To provide the most up-to-date information, the revision of our documents on the World Wide Web will be the most current. Your printed copy may be an earlier revision. To verify you have the latest information available, refer to: http://freescale.com/ The following revision history table summarizes changes contained in this document. Revision Number Revision Date 1 6/2006 Advance Information for alpha samples customers 2 9/2007 Product Launch. Removed the 64-pin QFN package. Changed from standard to extended mode for MSCAN registers in register summary. Corrected Block diagrams for SCI. Updated the latest Temp Sensor information. Made FTSTMOD reserved. Updated device to use the ADC 12-bit module. Revised the MCG module. Updated the CPU Instruction Set table. Updated the TPM block module to version 3. Added the TPM block module version 2 as an appendix for devices using 3M05C (or earlier) mask sets. Heavily revised the Electricals appendix. 3 10/2007 Removed two tables that were inadvertently included in the MC9S08DZ60 version of the book. 4 6/2008 Sustaining update. Incorporated PS Issues # 2765, 3177, 3236, 3292, 3311, 3312, 3326, 3335, 3345, 3382, 2795, 3382 and 3386 PLL Jitter Spec update. Also, added internal reference clock trim adjustment statement to Features page. Updated the TPM module to the latest version. Adjusted values in Table A-13 Control Timing row 2 and in Table A-6 DC Characteristics row 24 so that it references 5.0 V instead of 3.0 V. Description of Changes (c) Freescale Semiconductor, Inc., 2007-2008. All rights reserved. This product incorporates SuperFlash(R) Technology licensed from SST. MC9S08DZ60 Series Data Sheet, Rev. 4 6 Freescale Semiconductor List of Chapters Chapter Title Page Chapter 1 Device Overview .............................................................................. 21 Chapter 2 Pins and Connections ..................................................................... 27 Chapter 3 Modes of Operation ......................................................................... 35 Chapter 4 Memory ............................................................................................. 41 Chapter 5 Resets, Interrupts, and General System Control.......................... 69 Chapter 6 Parallel Input/Output Control.......................................................... 85 Chapter 7 Central Processor Unit (S08CPUV3) ............................................ 115 Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) ............................. 135 Chapter 9 Analog Comparator (S08ACMPV3) .............................................. 167 Chapter 10 Analog-to-Digital Converter (S08ADC12V1)................................ 173 Chapter 11 Inter-Integrated Circuit (S08IICV2) ............................................... 199 Chapter 12 Freescale Controller Area Network (S08MSCANV1) .................. 219 Chapter 13 Serial Peripheral Interface (S08SPIV3) ........................................ 273 Chapter 14 Serial Communications Interface (S08SCIV4)............................. 289 Chapter 15 Real-Time Counter (S08RTCV1) ................................................... 309 Chapter 16 Timer Pulse-Width Modulator (S08TPMV3) ................................. 319 Chapter 17 Development Support ................................................................... 347 Appendix A Electrical Characteristics.............................................................. 369 Appendix B Timer Pulse-Width Modulator (TPMV2) ....................................... 391 Appendix C Ordering Information and Mechanical Drawings........................ 405 MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 7 Contents Section Number Title Page Chapter 1 Device Overview 1.1 1.2 1.3 Devices in the MC9S08DZ60 Series................................................................................................21 MCU Block Diagram .......................................................................................................................22 System Clock Distribution ...............................................................................................................24 Chapter 2 Pins and Connections 2.1 2.2 Device Pin Assignment ....................................................................................................................27 Recommended System Connections ................................................................................................30 2.2.1 Power ................................................................................................................................31 2.2.2 Oscillator ...........................................................................................................................31 2.2.3 RESET ..............................................................................................................................31 2.2.4 Background / Mode Select (BKGD/MS) ..........................................................................32 2.2.5 ADC Reference Pins (VREFH, VREFL) ..............................................................................32 2.2.6 General-Purpose I/O and Peripheral Ports ........................................................................32 Chapter 3 Modes of Operation 3.1 3.2 3.3 3.4 3.5 3.6 Introduction ......................................................................................................................................35 Features ............................................................................................................................................35 Run Mode.........................................................................................................................................35 Active Background Mode.................................................................................................................35 Wait Mode ........................................................................................................................................36 Stop Modes.......................................................................................................................................37 3.6.1 Stop3 Mode .......................................................................................................................37 3.6.2 Stop2 Mode .......................................................................................................................38 3.6.3 On-Chip Peripheral Modules in Stop Modes ....................................................................39 Chapter 4 Memory 4.1 4.2 4.3 4.4 4.5 MC9S08DZ60 Series Memory Map ................................................................................................41 Reset and Interrupt Vector Assignments ..........................................................................................42 Register Addresses and Bit Assignments.........................................................................................44 RAM.................................................................................................................................................52 Flash and EEPROM .........................................................................................................................52 4.5.1 Features .............................................................................................................................52 MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 9 Section Number 4.5.2 4.5.3 4.5.4 4.5.5 4.5.6 4.5.7 4.5.8 4.5.9 4.5.10 4.5.11 Title Page Program and Erase Times .................................................................................................53 Program and Erase Command Execution .........................................................................53 Burst Program Execution ..................................................................................................55 Sector Erase Abort ............................................................................................................57 Access Errors ....................................................................................................................58 Block Protection ................................................................................................................59 Vector Redirection ............................................................................................................59 Security .............................................................................................................................59 EEPROM Mapping ...........................................................................................................61 Flash and EEPROM Registers and Control Bits ...............................................................61 Chapter 5 Resets, Interrupts, and General System Control 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 Introduction ......................................................................................................................................69 Features ............................................................................................................................................69 MCU Reset.......................................................................................................................................69 Computer Operating Properly (COP) Watchdog..............................................................................70 Interrupts ..........................................................................................................................................71 5.5.1 Interrupt Stack Frame .......................................................................................................72 5.5.2 External Interrupt Request (IRQ) Pin ...............................................................................72 5.5.3 Interrupt Vectors, Sources, and Local Masks ....................................................................73 Low-Voltage Detect (LVD) System .................................................................................................75 5.6.1 Power-On Reset Operation ...............................................................................................75 5.6.2 Low-Voltage Detection (LVD) Reset Operation ...............................................................75 5.6.3 Low-Voltage Warning (LVW) Interrupt Operation ...........................................................75 MCLK Output ..................................................................................................................................75 Reset, Interrupt, and System Control Registers and Control Bits ....................................................76 5.8.1 Interrupt Pin Request Status and Control Register (IRQSC) ............................................77 5.8.2 System Reset Status Register (SRS) .................................................................................78 5.8.3 System Background Debug Force Reset Register (SBDFR) ............................................79 5.8.4 System Options Register 1 (SOPT1) ................................................................................80 5.8.5 System Options Register 2 (SOPT2) ................................................................................81 5.8.6 System Device Identification Register (SDIDH, SDIDL) ................................................82 5.8.7 System Power Management Status and Control 1 Register (SPMSC1) ...........................83 5.8.8 System Power Management Status and Control 2 Register (SPMSC2) ...........................84 Chapter 6 Parallel Input/Output Control 6.1 6.2 6.3 Port Data and Data Direction ...........................................................................................................85 Pull-up, Slew Rate, and Drive Strength............................................................................................86 Pin Interrupts ....................................................................................................................................87 6.3.1 Edge Only Sensitivity .......................................................................................................87 MC9S08DZ60 Series Data Sheet, Rev. 4 10 Freescale Semiconductor Section Number 6.4 6.5 Title Page 6.3.2 Edge and Level Sensitivity ................................................................................................88 6.3.3 Pull-up/Pull-down Resistors .............................................................................................88 6.3.4 Pin Interrupt Initialization .................................................................................................88 Pin Behavior in Stop Modes.............................................................................................................88 Parallel I/O and Pin Control Registers .............................................................................................89 6.5.1 Port A Registers ................................................................................................................90 6.5.2 Port B Registers ................................................................................................................94 6.5.3 Port C Registers ................................................................................................................98 6.5.4 Port D Registers ..............................................................................................................101 6.5.5 Port E Registers ...............................................................................................................105 6.5.6 Port F Registers ...............................................................................................................108 6.5.7 Port G Registers ..............................................................................................................111 Chapter 7 Central Processor Unit (S08CPUV3) 7.1 7.2 7.3 7.4 7.5 Introduction ....................................................................................................................................115 7.1.1 Features ...........................................................................................................................115 Programmer's Model and CPU Registers ......................................................................................116 7.2.1 Accumulator (A) .............................................................................................................116 7.2.2 Index Register (H:X) .......................................................................................................116 7.2.3 Stack Pointer (SP) ...........................................................................................................117 7.2.4 Program Counter (PC) ....................................................................................................117 7.2.5 Condition Code Register (CCR) .....................................................................................117 Addressing Modes..........................................................................................................................119 7.3.1 Inherent Addressing Mode (INH) ...................................................................................119 7.3.2 Relative Addressing Mode (REL) ...................................................................................119 7.3.3 Immediate Addressing Mode (IMM) ..............................................................................119 7.3.4 Direct Addressing Mode (DIR) ......................................................................................119 7.3.5 Extended Addressing Mode (EXT) ................................................................................120 7.3.6 Indexed Addressing Mode ..............................................................................................120 Special Operations..........................................................................................................................121 7.4.1 Reset Sequence ...............................................................................................................121 7.4.2 Interrupt Sequence ..........................................................................................................121 7.4.3 Wait Mode Operation ......................................................................................................122 7.4.4 Stop Mode Operation ......................................................................................................122 7.4.5 BGND Instruction ...........................................................................................................123 HCS08 Instruction Set Summary ...................................................................................................124 Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) 8.1 Introduction ....................................................................................................................................135 8.1.1 Features ...........................................................................................................................137 MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 11 Section Number 8.2 8.3 8.4 8.5 Title Page 8.1.2 Modes of Operation ........................................................................................................139 External Signal Description ...........................................................................................................139 Register Definition .........................................................................................................................140 8.3.1 MCG Control Register 1 (MCGC1) ...............................................................................140 8.3.2 MCG Control Register 2 (MCGC2) ...............................................................................141 8.3.3 MCG Trim Register (MCGTRM) ...................................................................................142 8.3.4 MCG Status and Control Register (MCGSC) .................................................................143 8.3.5 MCG Control Register 3 (MCGC3) ...............................................................................144 Functional Description ...................................................................................................................146 8.4.1 Operational Modes ..........................................................................................................146 8.4.2 Mode Switching ..............................................................................................................150 8.4.3 Bus Frequency Divider ...................................................................................................151 8.4.4 Low Power Bit Usage .....................................................................................................151 8.4.5 Internal Reference Clock ................................................................................................151 8.4.6 External Reference Clock ...............................................................................................151 8.4.7 Fixed Frequency Clock ...................................................................................................152 Initialization / Application Information .........................................................................................152 8.5.1 MCG Module Initialization Sequence ............................................................................152 8.5.2 MCG Mode Switching ....................................................................................................153 8.5.3 Calibrating the Internal Reference Clock (IRC) .............................................................164 Chapter 9 Analog Comparator (S08ACMPV3) 9.1 9.2 9.3 9.4 Introduction ....................................................................................................................................167 9.1.1 ACMP Configuration Information ..................................................................................167 9.1.2 Features ...........................................................................................................................169 9.1.3 Modes of Operation ........................................................................................................169 9.1.4 Block Diagram ................................................................................................................170 External Signal Description ...........................................................................................................170 Memory Map/Register Definition ..................................................................................................171 9.3.1 ACMPx Status and Control Register (ACMPxSC) .........................................................171 Functional Description ...................................................................................................................172 Chapter 10 Analog-to-Digital Converter (S08ADC12V1) 10.1 Introduction ....................................................................................................................................173 10.1.1 Analog Power and Ground Signal Names ......................................................................173 10.1.2 Channel Assignments ......................................................................................................173 10.1.3 Alternate Clock ...............................................................................................................174 10.1.4 Hardware Trigger ............................................................................................................174 10.1.5 Temperature Sensor ........................................................................................................175 10.1.6 Features ...........................................................................................................................177 MC9S08DZ60 Series Data Sheet, Rev. 4 12 Freescale Semiconductor Section Number Title Page 10.1.7 ADC Module Block Diagram .........................................................................................177 10.2 External Signal Description ...........................................................................................................178 10.2.1 Analog Power (VDDAD) ..................................................................................................179 10.2.2 Analog Ground (VSSAD) .................................................................................................179 10.2.3 Voltage Reference High (VREFH) ...................................................................................179 10.2.4 Voltage Reference Low (VREFL) .....................................................................................179 10.2.5 Analog Channel Inputs (ADx) ........................................................................................179 10.3 Register Definition .........................................................................................................................179 10.3.1 Status and Control Register 1 (ADCSC1) ......................................................................179 10.3.2 Status and Control Register 2 (ADCSC2) ......................................................................181 10.3.3 Data Result High Register (ADCRH) .............................................................................181 10.3.4 Data Result Low Register (ADCRL) ..............................................................................182 10.3.5 Compare Value High Register (ADCCVH) ....................................................................182 10.3.6 Compare Value Low Register (ADCCVL) .....................................................................183 10.3.7 Configuration Register (ADCCFG) ................................................................................183 10.3.8 Pin Control 1 Register (APCTL1) ..................................................................................184 10.3.9 Pin Control 2 Register (APCTL2) ..................................................................................185 10.3.10Pin Control 3 Register (APCTL3) ..................................................................................186 10.4 Functional Description ...................................................................................................................187 10.4.1 Clock Select and Divide Control ....................................................................................188 10.4.2 Input Select and Pin Control ...........................................................................................188 10.4.3 Hardware Trigger ............................................................................................................188 10.4.4 Conversion Control .........................................................................................................188 10.4.5 Automatic Compare Function .........................................................................................191 10.4.6 MCU Wait Mode Operation ............................................................................................191 10.4.7 MCU Stop3 Mode Operation ..........................................................................................192 10.4.8 MCU Stop2 Mode Operation ..........................................................................................192 10.5 Initialization Information ...............................................................................................................193 10.5.1 ADC Module Initialization Example .............................................................................193 10.6 Application Information.................................................................................................................195 10.6.1 External Pins and Routing ..............................................................................................195 10.6.2 Sources of Error ..............................................................................................................196 Chapter 11 Inter-Integrated Circuit (S08IICV2) 11.1 Introduction ....................................................................................................................................199 11.1.1 Features ...........................................................................................................................201 11.1.2 Modes of Operation ........................................................................................................201 11.1.3 Block Diagram ................................................................................................................202 11.2 External Signal Description ...........................................................................................................202 11.2.1 SCL -- Serial Clock Line ...............................................................................................202 11.2.2 SDA -- Serial Data Line ................................................................................................202 MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 13 Section Number Title Page 11.3 Register Definition .........................................................................................................................202 11.3.1 IIC Address Register (IICA) ...........................................................................................203 11.3.2 IIC Frequency Divider Register (IICF) ...........................................................................203 11.3.3 IIC Control Register (IICC1) ..........................................................................................206 11.3.4 IIC Status Register (IICS) ...............................................................................................207 11.3.5 IIC Data I/O Register (IICD) ..........................................................................................208 11.3.6 IIC Control Register 2 (IICC2) .......................................................................................208 11.4 Functional Description ...................................................................................................................209 11.4.1 IIC Protocol .....................................................................................................................209 11.4.2 10-bit Address .................................................................................................................213 11.4.3 General Call Address ......................................................................................................214 11.5 Resets .............................................................................................................................................214 11.6 Interrupts ........................................................................................................................................214 11.6.1 Byte Transfer Interrupt ....................................................................................................214 11.6.2 Address Detect Interrupt .................................................................................................214 11.6.3 Arbitration Lost Interrupt ................................................................................................214 11.7 Initialization/Application Information ...........................................................................................216 Chapter 12 Freescale Controller Area Network (S08MSCANV1) 12.1 Introduction ....................................................................................................................................219 12.1.1 Features ...........................................................................................................................221 12.1.2 Modes of Operation ........................................................................................................221 12.1.3 Block Diagram ................................................................................................................222 12.2 External Signal Description ...........................................................................................................222 12.2.1 RXCAN -- CAN Receiver Input Pin .............................................................................222 12.2.2 TXCAN -- CAN Transmitter Output Pin .....................................................................222 12.2.3 CAN System ...................................................................................................................222 12.3 Register Definition .........................................................................................................................223 12.3.1 MSCAN Control Register 0 (CANCTL0) ......................................................................223 12.3.2 MSCAN Control Register 1 (CANCTL1) ......................................................................226 12.3.3 MSCAN Bus Timing Register 0 (CANBTR0) ...............................................................227 12.3.4 MSCAN Bus Timing Register 1 (CANBTR1) ...............................................................228 12.3.5 MSCAN Receiver Interrupt Enable Register (CANRIER) .............................................231 12.3.6 MSCAN Transmitter Flag Register (CANTFLG) ..........................................................232 12.3.7 MSCAN Transmitter Interrupt Enable Register (CANTIER) ........................................233 12.3.8 MSCAN Transmitter Message Abort Request Register (CANTARQ) ...........................234 12.3.9 MSCAN Transmitter Message Abort Acknowledge Register (CANTAAK) .................235 12.3.10MSCAN Transmit Buffer Selection Register (CANTBSEL) .........................................235 12.3.11MSCAN Identifier Acceptance Control Register (CANIDAC) ......................................236 12.3.12MSCAN Miscellaneous Register (CANMISC) ..............................................................237 12.3.13MSCAN Receive Error Counter (CANRXERR) ............................................................238 MC9S08DZ60 Series Data Sheet, Rev. 4 14 Freescale Semiconductor Section Number Title Page 12.3.14MSCAN Transmit Error Counter (CANTXERR) ..........................................................239 12.3.15MSCAN Identifier Acceptance Registers (CANIDAR0-7) ............................................239 12.3.16MSCAN Identifier Mask Registers (CANIDMR0-CANIDMR7) .................................240 12.4 Programmer's Model of Message Storage .....................................................................................241 12.4.1 Identifier Registers (IDR0-IDR3) ...................................................................................244 12.4.2 IDR0-IDR3 for Standard Identifier Mapping .................................................................246 12.4.3 Data Segment Registers (DSR0-7) .................................................................................247 12.4.4 Data Length Register (DLR) ...........................................................................................248 12.4.5 Transmit Buffer Priority Register (TBPR) ......................................................................249 12.4.6 Time Stamp Register (TSRH-TSRL) .............................................................................249 12.5 Functional Description ...................................................................................................................250 12.5.1 General ............................................................................................................................250 12.5.2 Message Storage .............................................................................................................251 12.5.3 Identifier Acceptance Filter .............................................................................................254 12.5.4 Modes of Operation ........................................................................................................261 12.5.5 Low-Power Options ........................................................................................................262 12.5.6 Reset Initialization ..........................................................................................................268 12.5.7 Interrupts .........................................................................................................................268 12.6 Initialization/Application Information ...........................................................................................270 12.6.1 MSCAN initialization .....................................................................................................270 12.6.2 Bus-Off Recovery ...........................................................................................................271 Chapter 13 Serial Peripheral Interface (S08SPIV3) 13.1 Introduction ....................................................................................................................................273 13.1.1 Features ...........................................................................................................................275 13.1.2 Block Diagrams ..............................................................................................................275 13.1.3 SPI Baud Rate Generation ..............................................................................................277 13.2 External Signal Description ...........................................................................................................278 13.2.1 SPSCK -- SPI Serial Clock ............................................................................................278 13.2.2 MOSI -- Master Data Out, Slave Data In ......................................................................278 13.2.3 MISO -- Master Data In, Slave Data Out ......................................................................278 13.2.4 SS -- Slave Select ...........................................................................................................278 13.3 Modes of Operation........................................................................................................................279 13.3.1 SPI in Stop Modes ..........................................................................................................279 13.4 Register Definition .........................................................................................................................279 13.4.1 SPI Control Register 1 (SPIC1) ......................................................................................279 13.4.2 SPI Control Register 2 (SPIC2) ......................................................................................280 13.4.3 SPI Baud Rate Register (SPIBR) ....................................................................................281 13.4.4 SPI Status Register (SPIS) ..............................................................................................282 13.4.5 SPI Data Register (SPID) ................................................................................................283 13.5 Functional Description ...................................................................................................................284 MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 15 Section Number Title Page 13.5.1 SPI Clock Formats ..........................................................................................................284 13.5.2 SPI Interrupts ..................................................................................................................287 13.5.3 Mode Fault Detection .....................................................................................................287 Chapter 14 Serial Communications Interface (S08SCIV4) 14.1 Introduction ....................................................................................................................................289 14.1.1 SCI2 Configuration Information .....................................................................................289 14.1.2 Features ...........................................................................................................................291 14.1.3 Modes of Operation ........................................................................................................291 14.1.4 Block Diagram ................................................................................................................292 14.2 Register Definition .........................................................................................................................294 14.2.1 SCI Baud Rate Registers (SCIxBDH, SCIxBDL) ..........................................................294 14.2.2 SCI Control Register 1 (SCIxC1) ...................................................................................295 14.2.3 SCI Control Register 2 (SCIxC2) ...................................................................................296 14.2.4 SCI Status Register 1 (SCIxS1) ......................................................................................297 14.2.5 SCI Status Register 2 (SCIxS2) ......................................................................................299 14.2.6 SCI Control Register 3 (SCIxC3) ...................................................................................300 14.2.7 SCI Data Register (SCIxD) .............................................................................................301 14.3 Functional Description ...................................................................................................................301 14.3.1 Baud Rate Generation .....................................................................................................301 14.3.2 Transmitter Functional Description ................................................................................302 14.3.3 Receiver Functional Description .....................................................................................303 14.3.4 Interrupts and Status Flags ..............................................................................................305 14.3.5 Additional SCI Functions ...............................................................................................306 Chapter 15 Real-Time Counter (S08RTCV1) 15.1 Introduction ....................................................................................................................................309 15.1.1 RTC Clock Signal Names ...............................................................................................309 15.1.2 Features ...........................................................................................................................311 15.1.3 Modes of Operation ........................................................................................................311 15.1.4 Block Diagram ................................................................................................................312 15.2 External Signal Description ...........................................................................................................312 15.3 Register Definition .........................................................................................................................312 15.3.1 RTC Status and Control Register (RTCSC) ....................................................................313 15.3.2 RTC Counter Register (RTCCNT) ..................................................................................314 15.3.3 RTC Modulo Register (RTCMOD) ................................................................................314 15.4 Functional Description ...................................................................................................................314 15.4.1 RTC Operation Example .................................................................................................315 15.5 Initialization/Application Information ...........................................................................................316 MC9S08DZ60 Series Data Sheet, Rev. 4 16 Freescale Semiconductor Section Number Title Page Chapter 16 Timer Pulse-Width Modulator (S08TPMV3) 16.1 Introduction ....................................................................................................................................319 16.1.1 Features ...........................................................................................................................321 16.1.2 Modes of Operation ........................................................................................................321 16.1.3 Block Diagram ................................................................................................................322 16.2 Signal Description ..........................................................................................................................324 16.2.1 Detailed Signal Descriptions ...........................................................................................324 16.3 Register Definition .........................................................................................................................328 16.3.1 TPM Status and Control Register (TPMxSC) ................................................................328 16.3.2 TPM-Counter Registers (TPMxCNTH:TPMxCNTL) ....................................................329 16.3.3 TPM Counter Modulo Registers (TPMxMODH:TPMxMODL) ....................................330 16.3.4 TPM Channel n Status and Control Register (TPMxCnSC) ..........................................331 16.3.5 TPM Channel Value Registers (TPMxCnVH:TPMxCnVL) ..........................................333 16.4 Functional Description ...................................................................................................................334 16.4.1 Counter ............................................................................................................................335 16.4.2 Channel Mode Selection .................................................................................................337 16.5 Reset Overview ..............................................................................................................................340 16.5.1 General ............................................................................................................................340 16.5.2 Description of Reset Operation .......................................................................................340 16.6 Interrupts ........................................................................................................................................340 16.6.1 General ............................................................................................................................340 16.6.2 Description of Interrupt Operation ..................................................................................341 16.7 The Differences from TPM v2 to TPM v3.....................................................................................342 Chapter 17 Development Support 17.1 Introduction ....................................................................................................................................347 17.1.1 Forcing Active Background ............................................................................................347 17.1.2 Features ...........................................................................................................................348 17.2 Background Debug Controller (BDC) ...........................................................................................348 17.2.1 BKGD Pin Description ...................................................................................................349 17.2.2 Communication Details ..................................................................................................350 17.2.3 BDC Commands .............................................................................................................354 17.2.4 BDC Hardware Breakpoint .............................................................................................356 17.3 On-Chip Debug System (DBG) .....................................................................................................357 17.3.1 Comparators A and B ......................................................................................................357 17.3.2 Bus Capture Information and FIFO Operation ...............................................................357 17.3.3 Change-of-Flow Information ..........................................................................................358 17.3.4 Tag vs. Force Breakpoints and Triggers .........................................................................358 17.3.5 Trigger Modes .................................................................................................................359 17.3.6 Hardware Breakpoints ....................................................................................................361 MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 17 Section Number Title Page 17.4 Register Definition .........................................................................................................................361 17.4.1 BDC Registers and Control Bits .....................................................................................361 17.4.2 System Background Debug Force Reset Register (SBDFR) ..........................................363 17.4.3 DBG Registers and Control Bits .....................................................................................364 Appendix A Electrical Characteristics A.1 A.2 A.3 A.4 A.5 A.6 A.7 A.8 A.9 A.10 A.11 A.12 Introduction ...................................................................................................................................369 Parameter Classification ................................................................................................................369 Absolute Maximum Ratings ..........................................................................................................369 Thermal Characteristics .................................................................................................................370 ESD Protection and Latch-Up Immunity ......................................................................................372 DC Characteristics .........................................................................................................................373 Supply Current Characteristics ......................................................................................................375 Analog Comparator (ACMP) Electricals ......................................................................................376 ADC Characteristics ......................................................................................................................376 External Oscillator (XOSC) Characteristics .................................................................................380 MCG Specifications ......................................................................................................................381 AC Characteristics .........................................................................................................................383 A.12.1 Control Timing ...............................................................................................................383 A.12.2 Timer/PWM ....................................................................................................................384 A.12.3 MSCAN ..........................................................................................................................385 A.12.4 SPI ...................................................................................................................................386 A.13 Flash and EEPROM ......................................................................................................................389 A.14 EMC Performance .........................................................................................................................390 A.14.1 Radiated Emissions .........................................................................................................390 Appendix B Timer Pulse-Width Modulator (TPMV2) B.0.1 Features ...........................................................................................................................391 B.0.2 Block Diagram ................................................................................................................391 B.1 External Signal Description ...........................................................................................................393 B.1.1 External TPM Clock Sources ..........................................................................................393 B.1.2 TPMxCHn -- TPMx Channel n I/O Pins .......................................................................393 B.2 Register Definition .........................................................................................................................393 B.2.1 Timer Status and Control Register (TPMxSC) ...............................................................394 B.2.2 Timer Counter Registers (TPMxCNTH:TPMxCNTL) ...................................................395 B.2.3 Timer Counter Modulo Registers (TPMxMODH:TPMxMODL) ..................................396 B.2.4 Timer Channel n Status and Control Register (TPMxCnSC) .........................................397 B.2.5 Timer Channel Value Registers (TPMxCnVH:TPMxCnVL) .........................................398 B.3 Functional Description ...................................................................................................................399 B.3.1 Counter ............................................................................................................................399 MC9S08DZ60 Series Data Sheet, Rev. 4 18 Freescale Semiconductor Section Number Title Page B.3.2 Channel Mode Selection .................................................................................................400 B.3.3 Center-Aligned PWM Mode ...........................................................................................402 B.4 TPM Interrupts ...............................................................................................................................403 B.4.1 Clearing Timer Interrupt Flags .......................................................................................403 B.4.2 Timer Overflow Interrupt Description ............................................................................403 B.4.3 Channel Event Interrupt Description ..............................................................................404 B.4.4 PWM End-of-Duty-Cycle Events ...................................................................................404 Appendix C Ordering Information and Mechanical Drawings C.1 Ordering Information ....................................................................................................................405 C.1.1 MC9S08DZ60 Series Devices ........................................................................................405 C.2 Mechanical Drawings ....................................................................................................................405 MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 19 Chapter 1 Device Overview MC9S08DZ60 Series devices provide significant value to customers looking to combine Controller Area Network (CAN) and embedded EEPROM in their applications. This combination will provide lower costs, enhanced performance, and higher quality. 1.1 Devices in the MC9S08DZ60 Series This data sheet covers members of the MC9S08DZ60 Series of MCUs: * MC9S08DZ60 * MC9S08DZ48 * MC9S08DZ32 * MC9S08DZ16 Table 1-1 summarizes the feature set available in the MC9S08DZ60 Series. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 21 Chapter 1 Device Overview t Table 1-1. MC9S08DZ60 Series Features by MCU and Pin Count Feature MC9S08DZ60 MC9S08DZ48 MC9S08DZ32 MC9S08DZ16 Flash size (bytes) 60032 49152 33792 16896 RAM size (bytes) 4096 3072 2048 1024 EEPROM size (bytes) 2048 1536 1024 512 Pin quantity 64 48 32 64 48 no yes yes1 10 24 16 ACMP1 32 64 48 32 48 32 no yes yes1 no yes1 no 10 24 16 10 16 10 6 6 4 6 4 yes 1 ACMP2 yes yes ADC channels 24 16 DBG yes IIC yes IRQ yes MCG yes MSCAN yes RTC yes SCI1 yes SCI2 yes SPI yes TPM1 channels 6 6 4 TPM2 channels 6 6 4 2 XOSC yes COP Watchdog yes 1 1.2 ACMP2O is not available. MCU Block Diagram Figure 1-1 is the MC9S08DZ60 Series system-level block diagram. MC9S08DZ60 Series Data Sheet, Rev. 4 22 Freescale Semiconductor PORT A PTA7/PIA7/ADP7/IRQ PTA6/PIA6/ADP6 PTA5/PIA5/ADP5 PTA4/PIA4/ADP4 PTA3/PIA3/ADP3/ACMP1O PTA2/PIA2/ADP2/ACMP1PTA1/PIA1/ADP1/ACMP1+ PTA0/PIA0/ADP0/MCLK PORT B PTB7/PIB7/ADP15 PTB6/PIB6/ADP14 PTB5/PIB5/ADP13 PTB4/PIB4/ADP12 PTB3/PIB3/ADP11 PTB2/PIB2/ADP10 PTB1/PIB1/ADP9 PTB0/PIB0/ADP8 PORT C PTC7/ADP23 PTC6/ADP22 PTC5/ADP21 PTC4/ADP20 PTC3/ADP19 PTC2/ADP18 PTC1/ADP17 PTC0/ADP16 PORT D PTD7/PID7/TPM1CH5 PTD6/PID6/TPM1CH4 PTD5/PID5/TPM1CH3 PTD4/PID4/TPM1CH2 PTD3/PID3/TPM1CH1 PTD2/PID2/TPM1CH0 PTD1/PID1/TPM2CH1 PTD0/PID0/TPM2CH0 PORT E PTE7/RxD2/RXCAN PTE6/TxD2/TXCAN PTE5/SDA/MISO PTE4/SCL/MOSI PTE3/SPSCK PTE2/SS PTE1/RxD1 PTE0/TxD1 PORT F PTF7 PTF6/ACMP2O PTF5/ACMP2PTF4/ACMP2+ PTF3/TPM2CLK/SDA PTF2/TPM1CLK/SCL PTF1/RxD2 PTF0/TxD2 PORT G Chapter 1 Device Overview PTG5 PTG4 PTG3 PTG2 PTG1/XTAL PTG0/EXTAL HCS08 CORE CPU BKGD/MS BDC ANALOG COMPARATOR (ACMP1) BKP ACMP1O ACMP1ACMP1+ HCS08 SYSTEM CONTROL RESETS AND INTERRUPTS MODES OF OPERATION POWER MANAGEMENT COP LVD INT IRQ ADP7-ADP0 24-CHANNEL,12-BIT ANALOG-TO-DIGITAL CONVERTER (ADC) VREFH VREFL VDDA VSSA USER Flash MC9S08DZ60 = 60K MC9S08DZ48 = 48K MC9S08DZ32 = 32K MC9S08DZ16 = 16K USER EEPROM MC9S08DZ60 = 2K TPM1CH5 TPM1CH0 6 TPM1CLK 2-CHANNEL TIMER/PWM MODULE (TPM2) TPM2CH1, TPM2CH0 TPM2CLK CONTROLLER AREA NETWORK (MSCAN) SERIAL PERIPHERAL INTERFACE MODULE (SPI) DEBUG MODULE (DBG) SERIAL COMMUNICATIONS INTERFACE (SCI1) VOLTAGE REGULATOR ADP15-ADP8 ADP23-ADP16 6-CHANNEL TIMER/PWM MODULE (TPM1) USER RAM MC9S08DZ60 = 4K REAL-TIME COUNTER (RTC) VDD VDD VSS VSS 8 IRQ RESET ANALOG COMPARATOR (ACMP2) IIC MODULE (IIC) SERIAL COMMUNICATIONS INTERFACE (SCI2) RxCAN TXCAN MISO MOSI SPSCK SS RxD1 TxD1 ACMP2O ACMP2ACMP2+ SDA SCL RxD2 TxD2 MULTI-PURPOSE CLOCK GENERATOR (MCG) XTAL EXTAL OSCILLATOR (XOSC) - VREFH/VREFL internally connected to VDDA/VSSA in 48-pin and 32-pin packages - VDD and VSS pins are each internally connected to two pads in 32-pin package - Pin not connected in 48-pin and 32-pin packages - Pin not connected in 32-pin package Figure 1-1. MC9S08DZ60 Block Diagram MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 23 Chapter 1 Device Overview Table 1-2 provides the functional version of the on-chip modules. Table 1-2. Module Versions Module Central Processor Unit (CPU) 3 Multi-Purpose Clock Generator (MCG) 1 Analog Comparator (ACMP) 3 Analog-to-Digital Converter (ADC) 1 Inter-Integrated Circuit (IIC) 2 Freescale's CAN (MSCAN) 1 Serial Peripheral Interface (SPI) 3 Serial Communications Interface (SCI) 4 Real-Time Counter (RTC) 1 Timer Pulse Width Modulator (TPM) 31 Debug Module (DBG) 2 1 1.3 Version 3M05C and older masks have TPM version 2. System Clock Distribution Figure 1-2 shows a simplified clock connection diagram. Some modules in the MCU have selectable clock inputs as shown. The clock inputs to the modules indicate the clock(s) that are used to drive the module function. The following are the clocks used in this MCU: * BUSCLK -- The frequency of the bus is always half of MCGOUT. * LPO -- Independent 1-kHz clock that can be selected as the source for the COP and RTC modules. * MCGOUT -- Primary output of the MCG and is twice the bus frequency. * MCGLCLK -- Development tools can select this clock source to speed up BDC communications in systems where BUSCLK is configured to run at a very slow frequency. * MCGERCLK -- External reference clock can be selected as the RTC clock source. It can also be used as the alternate clock for the ADC and MSCAN. * MCGIRCLK -- Internal reference clock can be selected as the RTC clock source. * MCGFFCLK -- Fixed frequency clock can be selected as clock source for the TPM1 and TPM2. * TPM1CLK -- External input clock source for TPM1. * TPM2CLK -- External input clock source for TPM2. MC9S08DZ60 Series Data Sheet, Rev. 4 24 Freescale Semiconductor Chapter 1 Device Overview 1 kHZ LPO COP RTC TPM1CLK TPM2CLK TPM1 TPM2 IIC SCI1 SCI2 SPI MCGERCLK MCGIRCLK MCGFFCLKVALID MCG MCGFFCLK /2 FFCLK* 1 0 MCGOUT /2 BUSCLK MCGLCLK XOSC CPU EXTAL BDC XTAL * The fixed frequency clock (FFCLK) is internally synchronized to the bus clock and must not exceed one half of the bus clock frequency. ADC MSCAN ADC has min and max frequency requirements.See the ADC chapter and electricals appendix for details. FLASH EEPROM Flash and EEPROM have frequency requirements for program and erase operation. See the electricals appendix for details. Figure 1-2. MC9S08DZ60 System Clock Distribution Diagram MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 25 Chapter 1 Device Overview MC9S08DZ60 Series Data Sheet, Rev. 4 26 Freescale Semiconductor Chapter 2 Pins and Connections This section describes signals that connect to package pins. It includes pinout diagrams, recommended system connections, and detailed discussions of signals. 2.1 Device Pin Assignment 64-Pin LQFP 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 PTB1/PIB1/ADP9 PTC2/ADP18 PTA0/PIA0/ADP0/MCLK PTC1/ADP17 PTB0/PIB0/ADP8 PTC0/ADP16 BKGD/MS PTD7/PID7/TPM1CH5 PTD6/PID6/TPM1CH4 VDD VSS PTF7 PTD5/PID5/TPM1CH3 PTD4/PID4/TPM1CH2 PTD3/PID3/TPM1CH1 PTD2/PID2/TPM1CH0 PTE2/SS PTE3/SPSCK PTE4/SCL/MOSI PTE5/SDA/MISO PTG2 PTG3 PTF0/TxD2 PTF1/RxD2 PTF2/TPM1CLK/SCL PTF3/TPM2CLK/SDA PTG4 PTG5 PTE6/TxD2/TXCAN PTE7/RxD2/RXCAN PTD0/PID0/TPM2CH0 PTD1/PID1/TPM2CH1 PTB6/PIB6/ADP14 PTC5/ADP21 PTA7/PIA7/ADP7/IRQ PTC6/ADP22 PTB7/PIB7/ADP15 PTC7/ADP23 VDD VSS PTG0/EXTAL PTG1/XTAL RESET PTF4/ACMP2+ PTF5/ACMP2PTF6/ACMP2O PTE0/TxD1 PTE1/RxD1 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 PTA6/PIA6/ADP6 PTB5/PIB5/ADP13 PTA5/PIA5/ADP5 PTC4/ADP20 PTB4/PIB4/ADP12 PTA4/PIA4/ADP4 VDDA VREFH VREFL VSSA PTA3/PIA3/ADP3/ACMP1O PTB3/PIB3/ADP11 PTC3/ADP19 PTA2/PIA2/ADP2/ACMP1PTB2/PIB2/ADP10 PTA1/PIA1/ADP1/ACMP1+ This section shows the pin assignments for MC9S08DZ60 Series MCUs in the available packages. Figure 2-1. 64-Pin LQFP MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 27 48-Pin LQFP 13 14 15 16 17 18 19 20 21 22 23 24 1 2 3 4 5 6 7 8 9 10 11 12 36 35 34 33 32 31 30 29 28 27 26 25 PTB1/PIB1/ADP9 PTA0/PIA0/ADP0/MCLK PTB0/PIB0/ADP8 BKGD/MS PTD7/PID7/TPM1CH5 PTD6/PID6/TPM1CH4 VDD VSS PTD5/PID5/TPM1CH3 PTD4/PID4/TPM1CH2 PTD3/PID3/TPM1CH1 PTD2/PID2/TPM1CH0 PTE2/SS PTE3/SPSCK PTE4/SCL/MOSI PTE5/SDA/MISO PTF0/TxD2 PTF1/RxD2 PTF2/TPM1CLK/SCL PTF3/TPM2CLK/SDA PTE6/TxD2/TXCAN PTE7/RxD2/RXCAN PTD0/PID0/TPM2CH0 PTD1/PID1/TPM2CH1 PTB6/PIB6/ADP14 PTA7/PIA7/ADP7/IRQ PTB7/PIB7/ADP15 VDD VSS PTG0/EXTAL PTG1/XTAL RESET PTF4/ACMP2+ PTF5/ACMP2PTE0/TxD1 PTE1/RxD1 48 47 46 45 44 43 42 41 40 39 38 37 PTA6/PIA6/ADP6 PTB5/PIB5/ADP13 PTA5/PIA5/ADP5 PTB4/PIB4/ADP12 PTA4/PIA4/ADP4 VDDA/VREFH VSSA/VREFL PTA3/PIA3/ADP3/ACMP1O PTB3/PIB3/ADP11 PTA2/PIA2/ADP2/ACMP1PTB2/PIB2/ADP10 PTA1/PIA1/ADP1/ACMP1+ Chapter 2 Pins and Connections VREFH and VREFL are internally connected to VDDA and VSSA, respectively. Figure 2-2. 48-Pin LQFP MC9S08DZ60 Series Data Sheet, Rev. 4 28 Freescale Semiconductor PTA4/PIA4/ADP4 VDDA/VREFH VSSA/VREFL PTA3/ADP3/ACMPO PTA2/ADP2/ACMP- 31 30 29 28 27 26 25 32 PTA7/PIA7/ADP7/IRQ 1 PTA1/ADP1/ACMP+ PTA5/PIA5/ADP5 PTA6/PIA6/ADP6 Chapter 2 Pins and Connections 24 PTB1/PIB1/ADP9 VDD 2 23 PTA0/PIA0/ADP0/MCLK VSS 3 22 PTB0/PIB0/ADP8 PTG0/EXTAL 4 21 BKGD/MS PTG1/XTAL 5 20 PTD5/PID5/TPM1CH3 RESET 6 19 PTD4/PID4/TPM1CH2 PTE0/TxD1 7 18 PTD3/PID3/TPM1CH1 8 10 11 12 13 14 9 PTD0/PID0/TPM2CH0 PTE7/RxD2/RXCAN PTE6/TxD2/TXCAN PTE5/SDA/MISO PTE4/SCL/MOSI 16 PTE3/SPSCK PTE2/SS 17 PTD2/PID2/TPM1CH0 15 PTD1/PID1/TPM2CH1 PTE1/RxD1 32-Pin LQFP VREFH and VREFL are internally connected to VDDA and VSSA, respectively. Figure 2-3. 32-Pin LQFP MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 29 Chapter 2 Pins and Connections 2.2 Recommended System Connections Figure 2-4 shows pin connections that are common to MC9S08DZ60 Series application systems. MC9S08DZ60 PTA0/PIA0/ADP0/MCLK VDD + PTA1/PIA1/ADP1/ACMP1+ CBY 0.1 F CBLK + 10 F 5V PTA2/PIA2/ADP2/ACMP1VSS SYSTEM POWER CBY 0.1 F PORT A VDDA VREFH VREFL VSSA PTA3/PIA3/ADP3/ACMP1O PTA4/PIA4/ADP4 PTA5/PIA5/ADP5 PTA6/PIA6/ADP6 IRQ PTA7/PIA7/ADP7/IRQ PTB0/PIB0/ADP8 PTB1/PIB1/ADP9 BACKGROUND HEADER VDD BKGD/MS VDD PORT B 4.7 k-10 k PTB2/PIB2/ADP10 PTB3/PIB3/ADP11 PTB4/PIB4/ADP12 PTB5/PIB5/ADP13 PTB6/PIB6/ADP14 PTB7/PIB7/ADP15 RESET OPTIONAL MANUAL RESET 0.1 F PORT C RF C1 X1 NOTES: 1. External crystal circuit not required if using the internal clock option. 2. RESET pin can only be used to reset into user mode, you can not enter BDM using RESET pin. BDM can be entered by holding MS low during POR or writing a 1 to BDFR in SBDFR with MS low after issuing BDM command. 3. RC filter on RESET pin recommended for noisy environments. 4. For 32-pin and 48-pin packages: VDDA and VSSA are double bonded to VREFH and VREFL respectively. PTC0/ADP16 PTC1/ADP17 PTC2/ADP18 PTC3/ADP19 PTC4/ADP20 PTC5/ADP21 PTC6/ADP22 PTC7/ADP23 RS PTD0/PID0/TPM2CH0 PTD1/PID1/TPM2CH1 C2 PTG0/EXTAL PTG1/XTAL PTG2 PTG3 PTD2/PID2/TPM1CH0 PORT G PORT D PTD4/PID4/TPM1CH2 PTD5/PID5/TPM1CH3 PTD6/PID6/TPM1CH4 PTD7/PID7/TPM1CH5 PTG4 PTG5 PTF0/TxD2 PTF1/RxD2 PTF2/TPM1CLK/SCL PTF3/TPM2CLK/SDA PTF4/ACMP2+ PTF5/ACMP2- PTF6/ACMP2O PTF7 PTD3/PID3/TPM1CH1 PORT F PORT E PTE0/TxD1 PTE1/RxD1 PTE2/SS PTE3/SPSCK PTE4/SCL/MOSI PTE5/SDA/MISO PTE6/TxD2/TXCAN PTE7/RxD2/RXCAN Figure 2-4. Basic System Connections (Shown in 64-Pin Package) MC9S08DZ60 Series Data Sheet, Rev. 4 30 Freescale Semiconductor Chapter 2 Pins and Connections 2.2.1 Power VDD and VSS are the primary power supply pins for the MCU. This voltage source supplies power to all I/O buffer circuitry and to an internal voltage regulator. The internal voltage regulator provides regulated lower-voltage source to the CPU and other internal circuitry of the MCU. Typically, application systems have two separate capacitors across the power pins. In this case, there should be a bulk electrolytic capacitor, such as a 10-F tantalum capacitor, to provide bulk charge storage for the overall system and a 0.1-F ceramic bypass capacitor located as near to the MCU power pins as practical to suppress high-frequency noise. The MC9S08DZ60 Series has two VDD pins except on the 32-pin package. Each pin must have a bypass capacitor for best noise suppression. VDDA and VSSA are the analog power supply pins for the MCU. This voltage source supplies power to the ADC module. A 0.1-F ceramic bypass capacitor should be located as near to the MCU power pins as practical to suppress high-frequency noise. 2.2.2 Oscillator Immediately after reset, the MCU uses an internally generated clock provided by the multi-purpose clock generator (MCG) module. For more information on the MCG, see Chapter 8, "Multi-Purpose Clock Generator (S08MCGV1)." The oscillator (XOSC) in this MCU is a Pierce oscillator that can accommodate a crystal or ceramic resonator. Rather than a crystal or ceramic resonator, an external oscillator can be connected to the EXTAL input pin. Refer to Figure 2-4 for the following discussion. RS (when used) and RF should be low-inductance resistors such as carbon composition resistors. Wire-wound resistors and some metal film resistors have too much inductance. C1 and C2 normally should be high-quality ceramic capacitors that are specifically designed for high-frequency applications. RF is used to provide a bias path to keep the EXTAL input in its linear range during crystal startup; its value is not generally critical. Typical systems use 1 M to 10 M. Higher values are sensitive to humidity, and lower values reduce gain and (in extreme cases) could prevent startup. C1 and C2 are typically in the 5-pF to 25-pF range and are chosen to match the requirements of a specific crystal or resonator. Be sure to take into account printed circuit board (PCB) capacitance and MCU pin capacitance when selecting C1 and C2. The crystal manufacturer typically specifies a load capacitance which is the series combination of C1 and C2 (which are usually the same size). As a first-order approximation, use 10 pF as an estimate of combined pin and PCB capacitance for each oscillator pin (EXTAL and XTAL). 2.2.3 RESET RESET is a dedicated pin with a pull-up device built in. It has input hysteresis, a high current output driver, and no output slew rate control. Internal power-on reset and low-voltage reset circuitry typically make external reset circuitry unnecessary. This pin is normally connected to the standard 6-pin background debug connector so a development system can directly reset the MCU system. If desired, a manual external reset can be added by supplying a simple switch to ground (pull reset pin low to force a reset). MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 31 Chapter 2 Pins and Connections Whenever any reset is initiated (whether from an external signal or from an internal system), the RESET pin is driven low for about 34 bus cycles. The reset circuitry decodes the cause of reset and records it by setting a corresponding bit in the system reset status register (SRS). 2.2.4 Background / Mode Select (BKGD/MS) While in reset, the BKGD/MS pin functions as a mode select pin. Immediately after reset rises, the pin functions as the background pin and can be used for background debug communication. While functioning as a background or mode select pin, the pin includes an internal pull-up device, input hysteresis, a standard output driver, and no output slew rate control. If nothing is connected to this pin, the MCU will enter normal operating mode at the rising edge of reset. If a debug system is connected to the 6-pin standard background debug header, it can hold BKGD low during the rising edge of reset which forces the MCU to active background mode. The BKGD/MS pin is used primarily for background debug controller (BDC) communications using a custom protocol that uses 16 clock cycles of the target MCU's BDC clock per bit time. The target MCU's BDC clock could be as fast as the bus clock rate, so there should never be any significant capacitance connected to the BKGD/MS pin that could interfere with background serial communications. Although the BKGD/MS pin is a pseudo open-drain pin, the background debug communication protocol provides brief, actively driven, high speedup pulses to ensure fast rise times. Small capacitances from cables and the absolute value of the internal pull-up device play almost no role in determining rise and fall times on the BKGD/MS pin. 2.2.5 ADC Reference Pins (VREFH, VREFL) The VREFH and VREFL pins are the voltage reference high and voltage reference low inputs, respectively, for the ADC module. 2.2.6 General-Purpose I/O and Peripheral Ports The MC9S08DZ60 Series series of MCUs support up to 53 general-purpose I/O pins and 1 input-only pin, which are shared with on-chip peripheral functions (timers, serial I/O, ADC, MSCAN, etc.). When a port pin is configured as a general-purpose output or a peripheral uses the port pin as an output, software can select one of two drive strengths and enable or disable slew rate control. When a port pin is configured as a general-purpose input or a peripheral uses the port pin as an input, software can enable a pull-up device. Immediately after reset, all of these pins are configured as high-impedance general-purpose inputs with internal pull-up devices disabled. When an on-chip peripheral system is controlling a pin, data direction control bits still determine what is read from port data registers even though the peripheral module controls the pin direction by controlling the enable for the pin's output buffer. For information about controlling these pins as general-purpose I/O pins, see Chapter 6, "Parallel Input/Output Control." MC9S08DZ60 Series Data Sheet, Rev. 4 32 Freescale Semiconductor Chapter 2 Pins and Connections NOTE To avoid extra current drain from floating input pins, the reset initialization routine in the application program should either enable on-chip pull-up devices or change the direction of unused or non-bonded pins to outputs so they do not float. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 33 Chapter 2 Pins and Connections Table 2-1. Pin Availability by Package Pin-Count 3 Pin Number <-- Lowest 64 48 32 Port Pin/Interrupt 1 1 -- PTB6 2 -- -- PTC5 3 2 1 PTA7 4 -- -- PTC6 5 3 -- PTB7 6 -- -- PTC7 7 4 PIB6 PIA7 PIB7 Priority Alt 1 5 3 9 6 4 PTG0 10 7 5 PTG1 11 8 6 Alt 2 Pin Number <-- Lowest 64 48 32 Port Pin/Interrupt TPM1CH0 ADP21 34 26 18 PTD3 PID3 TPM1CH1 ADP7 35 27 19 PTD4 PID4 TPM1CH2 ADP22 36 28 20 PTD5 PID5 TPM1CH3 ADP15 37 -- -- PTF7 ADP23 38 29 -- IRQ VSS VDD 39 30 -- VSS 40 31 -- PTD6 PID6 EXTAL 41 32 -- PTD7 PID7 XTAL 42 33 21 -- PTF4 ACMP2+ 44 34 22 PTB0 13 10 -- PTF5 ACMP2- 45 -- -- PTC1 14 -- -- PTF6 ACMP2O 46 35 23 PTA0 VDD TPM1CH4 TPM1CH5 BKGD ADP8 ADP17 PIA0 ADP0 15 11 7 PTE0 TxD1 16 12 8 PTE12 RxD12 48 36 24 PTB1 PIB1 ADP9 SS 49 37 25 PTA1 PIA1 ADP11 9 PTE2 SPSCK 50 38 -- PTB2 PIB2 ADP10 19 15 11 PTE4 SCL MOSI 51 39 26 PTA2 PIA2 ADP21 20 16 12 PTE5 SDA3 MISO 52 -- -- PTC3 53 40 -- PTB3 PIB3 ADP11 22 -- -- PTG3 54 41 27 PTA3 PIA3 ADP3 23 17 -- PTF0 TxD2 55 24 18 -- PTF1 RxD24 56 25 19 -- PTF2 TPM1CLK SCL3 57 26 20 -- PTF3 SDA3 58 TPM2CLK 27 -- -- PTG4 28 -- -- PTG5 VREFH VDDA 59 44 30 PTA4 PIA4 60 45 -- PTB4 PIB4 ADP4 ADP12 29 21 13 PTE6 4 TxD2 TXCAN 61 -- -- PTC4 30 22 14 PTE7 RxD24 RxCAN 62 46 31 PTA5 PIA5 ADP5 PIB5 ADP13 PIA6 ADP6 PID0 TPM2CH0 32 24 16 PTD1 PID1 TPM2CH1 64 48 32 PTA6 ACMP1O VREFL 43 29 31 23 15 PTD0 ACMP1-1 VSSA 42 28 63 47 -- PTB5 ACMP1+1 ADP19 21 -- -- PTG2 4 MCLK ADP18 3 18 14 10 PTE3 MS ADP16 PIB0 47 -- -- PTC2 17 13 Alt 2 PID2 43 -- -- PTC0 9 Alt 1 --> Highest 33 25 17 PTD2 RESET 12 Priority ADP14 2 8 --> Highest ADP20 1. If both of these analog modules are enabled, they both will have access to the pin. 2. Pin does not contain a clamp diode to VDD and should not be driven above VDD. The voltage measured on this pin when internal pull-up is enabled may be as low as VDD - 0.7 V. The internal gates connected to this pin are pulled to VDD. 3. The IIC module pins can be repositioned using IICPS bit in the SOPT1 register. The default reset locations are on PTF2 and PTF3. 4. The SCI2 module pins can be repositioned using SCI2PS bit in the SOPT1 register. The default reset locations are on PTF0 and PTF1. MC9S08DZ60 Series Data Sheet, Rev. 4 34 Freescale Semiconductor Chapter 3 Modes of Operation 3.1 Introduction The operating modes of the MC9S08DZ60 Series are described in this chapter. Entry into each mode, exit from each mode, and functionality while in each of the modes are described. 3.2 * * * 3.3 Features Active background mode for code development Wait mode -- CPU shuts down to conserve power; system clocks are running and full regulation is maintained Stop modes -- System clocks are stopped and voltage regulator is in standby -- Stop3 -- All internal circuits are powered for fast recovery -- Stop2 -- Partial power down of internal circuits; RAM content is retained Run Mode This is the normal operating mode for the MC9S08DZ60 Series. This mode is selected when the BKGD/MS pin is high at the rising edge of reset. In this mode, the CPU executes code from internal memory with execution beginning at the address fetched from memory at 0xFFFE-0xFFFF after reset. 3.4 Active Background Mode The active background mode functions are managed through the background debug controller (BDC) in the HCS08 core. The BDC, together with the on-chip debug module (DBG), provide the means for analyzing MCU operation during software development. Active background mode is entered in any of five ways: * When the BKGD/MS pin is low at the rising edge of reset * When a BACKGROUND command is received through the BKGD/MS pin * When a BGND instruction is executed * When encountering a BDC breakpoint * When encountering a DBG breakpoint After entering active background mode, the CPU is held in a suspended state waiting for serial background commands rather than executing instructions from the user application program. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 35 Chapter 3 Modes of Operation Background commands are of two types: * Non-intrusive commands, defined as commands that can be issued while the user program is running. Non-intrusive commands can be issued through the BKGD/MS pin while the MCU is in run mode; non-intrusive commands can also be executed when the MCU is in the active background mode. Non-intrusive commands include: -- Memory access commands -- Memory-access-with-status commands -- BDC register access commands -- The BACKGROUND command * Active background commands, which can only be executed while the MCU is in active background mode. Active background commands include commands to: -- Read or write CPU registers -- Trace one user program instruction at a time -- Leave active background mode to return to the user application program (GO) The active background mode is used to program a bootloader or user application program into the Flash program memory before the MCU is operated in run mode for the first time. When the MC9S08DZ60 Series is shipped from the Freescale Semiconductor factory, the Flash program memory is erased by default unless specifically noted so there is no program that could be executed in run mode until the Flash memory is initially programmed. The active background mode can also be used to erase and reprogram the Flash memory after it has been previously programmed. For additional information about the active background mode, refer to the Development Support chapter. 3.5 Wait Mode Wait mode is entered by executing a WAIT instruction. Upon execution of the WAIT instruction, the CPU enters a low-power state in which it is not clocked. The I bit in CCR is cleared when the CPU enters the wait mode, enabling interrupts. When an interrupt request occurs, the CPU exits the wait mode and resumes processing, beginning with the stacking operations leading to the interrupt service routine. While the MCU is in wait mode, there are some restrictions on which background debug commands can be used. Only the BACKGROUND command and memory-access-with-status commands are available when the MCU is in wait mode. The memory-access-with-status commands do not allow memory access, but they report an error indicating that the MCU is in either stop or wait mode. The BACKGROUND command can be used to wake the MCU from wait mode and enter active background mode. MC9S08DZ60 Series Data Sheet, Rev. 4 36 Freescale Semiconductor Chapter 3 Modes of Operation 3.6 Stop Modes One of two stop modes is entered upon execution of a STOP instruction when the STOPE bit in SOPT1 register is set. In both stop modes, all internal clocks are halted. The MCG module can be configured to leave the reference clocks running. See Chapter 8, "Multi-Purpose Clock Generator (S08MCGV1)," for more information. Table 3-1 shows all of the control bits that affect stop mode selection and the mode selected under various conditions. The selected mode is entered following the execution of a STOP instruction. Table 3-1. Stop Mode Selection STOPE ENBDM 1 0 x 1 LVDE LVDSE PPDC Stop Mode x x Stop modes disabled; illegal opcode reset if STOP instruction executed 1 x x Stop3 with BDM enabled 2 1 0 Both bits must be 1 x Stop3 with voltage regulator active 1 0 Either bit a 0 0 Stop3 1 0 Either bit a 0 1 Stop2 1 ENBDM is located in the BDCSCR, which is only accessible through BDC commands, see Section 17.4.1.1, "BDC Status and Control Register (BDCSCR)". 2 When in Stop3 mode with BDM enabled, The S IDD will be near RIDD levels because internal clocks are enabled. 3.6.1 Stop3 Mode Stop3 mode is entered by executing a STOP instruction under the conditions as shown in Table 3-1. The states of all of the internal registers and logic, RAM contents, and I/O pin states are maintained. Exit from stop3 is done by asserting RESET or an asynchronous interrupt pin. The asynchronous interrupt pins are IRQ, PIA0-PIA7, PIB0-PIB7, and PID0-PID7. Exit from stop3 can also be done by the low-voltage detect (LVD) reset, low-voltage warning (LVW) interrupt, ADC conversion complete interrupt, real-time clock (RTC) interrupt, MSCAN wake-up interrupt, or SCI receiver interrupt. If stop3 is exited by means of the RESET pin, the MCU will be reset and operation will resume after fetching the reset vector. Exit by means of an interrupt will result in the MCU fetching the appropriate interrupt vector. 3.6.1.1 LVD Enabled in Stop3 Mode The LVD system is capable of generating either an interrupt or a reset when the supply voltage drops below the LVD voltage. If the LVD is enabled in stop (LVDE and LVDSE bits in SPMSC1 both set) at the time the CPU executes a STOP instruction, then the voltage regulator remains active during stop mode. For the ADC to operate the LVD must be left enabled when entering stop3. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 37 Chapter 3 Modes of Operation 3.6.1.2 Active BDM Enabled in Stop3 Mode Entry into the active background mode from run mode is enabled if ENBDM in BDCSCR is set. This register is described in Chapter 17, "Development Support." If ENBDM is set when the CPU executes a STOP instruction, the system clocks to the background debug logic remain active when the MCU enters stop mode. Because of this, background debug communication remains possible. In addition, the voltage regulator does not enter its low-power standby state but maintains full internal regulation. Most background commands are not available in stop mode. The memory-access-with-status commands do not allow memory access, but they report an error indicating that the MCU is in either stop or wait mode. The BACKGROUND command can be used to wake the MCU from stop and enter active background mode if the ENBDM bit is set. After entering background debug mode, all background commands are available. 3.6.2 Stop2 Mode Stop2 mode is entered by executing a STOP instruction under the conditions as shown in Table 3-1. Most of the internal circuitry of the MCU is powered off in stop2 with the exception of the RAM. Upon entering stop2, all I/O pin control signals are latched so that the pins retain their states during stop2. Exit from stop2 is performed by asserting RESET. On 3M05C or older masksets only, exit from stop2 can also be performed by asserting PTA7/ADP7/IRQ. NOTE On 3M05C or older masksets only, PTA7/ADP7/IRQ is an active low wake-up and must be configured as an input prior to executing a STOP instruction to avoid an immediate exit from stop2. PTA7/ADP7/IRQ can be disabled as a wake-up if it is configured as a high driven output. For lowest power consumption in stop2, this pin should not be left open when configured as input (enable the internal pullup; or tie an external pullup/down device; or set pin as output). In addition, the real-time counter (RTC) can wake the MCU from stop2, if enabled. Upon wake-up from stop2 mode, the MCU starts up as from a power-on reset (POR): * All module control and status registers are reset * The LVD reset function is enabled and the MCU remains in the reset state if VDD is below the LVD trip point (low trip point selected due to POR) * The CPU takes the reset vector In addition to the above, upon waking up from stop2, the PPDF bit in SPMSC2 is set. This flag is used to direct user code to go to a stop2 recovery routine. PPDF remains set and the I/O pin states remain latched until a 1 is written to PPDACK in SPMSC2. MC9S08DZ60 Series Data Sheet, Rev. 4 38 Freescale Semiconductor Chapter 3 Modes of Operation To maintain I/O states for pins that were configured as general-purpose I/O before entering stop2, the user must restore the contents of the I/O port registers, which have been saved in RAM, to the port registers before writing to the PPDACK bit. If the port registers are not restored from RAM before writing to PPDACK, then the pins will switch to their reset states when PPDACK is written. For pins that were configured as peripheral I/O, the user must reconfigure the peripheral module that interfaces to the pin before writing to the PPDACK bit. If the peripheral module is not enabled before writing to PPDACK, the pins will be controlled by their associated port control registers when the I/O latches are opened. 3.6.3 On-Chip Peripheral Modules in Stop Modes When the MCU enters any stop mode, system clocks to the internal peripheral modules are stopped. Even in the exception case (ENBDM = 1), where clocks to the background debug logic continue to operate, clocks to the peripheral systems are halted to reduce power consumption. Refer to Section 3.6.2, "Stop2 Mode" and Section 3.6.1, "Stop3 Mode" for specific information on system behavior in stop modes. Table 3-2. Stop Mode Behavior Mode Peripheral Stop2 Stop3 CPU Off Standby RAM Standby Standby Flash/EEPROM Off Standby Parallel Port Registers Off Standby ACMP Off Off ADC Off Optionally On1 IIC Off Standby MCG Off Optionally On2 MSCAN Off RTC Optionally Standby On3 Optionally On3 SCI Off Standby SPI Off Standby TPM Off Standby Voltage Regulator Off Optionally On4 XOSC Off Optionally On5 States Held States Held I/O Pins BDM LVD/LVW Off 6 Optionally On Off 7 Optionally On 1 Requires the asynchronous ADC clock and LVD to be enabled, else in standby. IRCLKEN and IREFSTEN set in MCGC1, else in standby. 3 Requires the RTC to be enabled, else in standby. 4 Requires the LVD or BDC to be enabled. 2 MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 39 Chapter 3 Modes of Operation 5 ERCLKEN and EREFSTEN set in MCGC2 for, else in standby. For high frequency range (RANGE in MCGC2 set) requires the LVD to also be enabled in stop3. 6 If ENBDM is set when entering stop2, the MCU will actually enter stop3. 7 If LVDSE is set when entering stop2, the MCU will actually enter stop3. MC9S08DZ60 Series Data Sheet, Rev. 4 40 Freescale Semiconductor Chapter 4 Memory 4.1 MC9S08DZ60 Series Memory Map On-chip memory in the MC9S08DZ60 Series consists of RAM, EEPROM, and Flash program memory for nonvolatile data storage, and I/O and control/status registers. The registers are divided into three groups: * Direct-page registers (0x0000 through 0x007F) * High-page registers (0x1800 through 0x18FF) * Nonvolatile registers (0xFFB0 through 0xFFBF) MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 41 Chapter 4 Memory 0x0000 DIRECT PAGE REGISTERS 128 BYTES 0x007F 0x0080 RAM 4096 BYTES 2 x 1024 BYTES 0x17FF 0x1800 HIGH PAGE REGISTERS 256 BYTES 0x18FF 0x1900 UNIMPLEMENTED 3456 BYTES UNIMPLEMENTED 2176 BYTES FLASH 896 BYTES EEPROM1 0x0000 DIRECT PAGE REGISTERS 128 BYTES 0x007F 0x0080 RAM 2048 BYTES 0x087F 0x0880 0x0C7F 0x0C80 0x107F 0x1080 0x13FF 0x1400 0x0000 DIRECT PAGE REGISTERS 128 BYTES 0x007F 0x0080 RAM 3072 BYTES 0x14FF 0x1500 0x15FF 0x1600 EEPROM1 2 x 768 BYTES 0x17FF 0x1800 HIGH PAGE REGISTERS 256 BYTES 0x18FF 0x1900 EEPROM1 2 x 512 BYTES 0x17FF 0x1800 HIGH PAGE REGISTERS 256 BYTES 0x18FF 0x1900 UNIMPLEMENTED 25,344 BYTES UNIMPLEMENTED 9984 BYTES 0x3FFF 0x4000 0x0000 DIRECT PAGE REGISTERS 128 BYTES 0x007F 0x0080 RAM 1024 BYTES 0x047F 0x0480 UNIMPLEMENTED 4736 BYTES 0x16FF 0x1700 EEPROM1 0x17FF 2 x 256 BYTES 0x1800 HIGH PAGE REGISTERS 256 BYTES 0x18FF 0x1900 UNIMPLEMENTED 42,240 BYTES 0x7BFF 0x7C00 0xBDFF 0xBE00 FLASH 59136 BYTES 0xFFFF FLASH 49152 BYTES 0xFFFF MC9S08DZ60 1 FLASH 16896 BYTES FLASH 33792 BYTES 0xFFFF 0xFFFF MC9S08DZ48 MC9S08DZ16 MC9S08DZ32 EEPROM address range shows half the total EEPROM. See Section 4.5.10, "EEPROM Mapping" for more details. Figure 4-1. MC9S08DZ60 Memory Map 4.2 Reset and Interrupt Vector Assignments Table 4-1 shows address assignments for reset and interrupt vectors. The vector names shown in this table are the labels used in the MC9S08DZ60 Series equate file provided by Freescale Semiconductor. Table 4-1. Reset and Interrupt Vectors Address (High/Low) Vector Vector Name 0xFFC0:0xFFC1 ACMP2 Vacmp2 0xFFC2:0xFFC3 ACMP1 Vacmp1 0xFFC4:0xFFC5 MSCAN Transmit Vcantx 0xFFC6:0xFFC7 MSCAN Receive Vcanrx 0xFFC8:0xFFC9 MSCAN errors Vcanerr 0xFFCA:0xFFCB MSCAN wake up Vcanwu MC9S08DZ60 Series Data Sheet, Rev. 4 42 Freescale Semiconductor Chapter 4 Memory Table 4-1. Reset and Interrupt Vectors Address (High/Low) Vector Vector Name 0xFFCC:0xFFCD RTC Vrtc 0xFFCE:0xFFCF IIC Viic 0xFFD0:0xFFD1 ADC Conversion Vadc 0xFFD2:0xFFD3 Port A, Port B, Port D Vport 0xFFD4:0xFFD5 SCI2 Transmit Vsci2tx 0xFFD6:0xFFD7 SCI2 Receive Vsci2rx 0xFFD8:0xFFD9 SCI2 Error Vsci2err 0xFFDA:0xFFDB SCI1 Transmit Vsci1tx 0xFFDC:0xFFDD SCI1 Receive Vsci1rx 0xFFDE:0xFFDF SCI1 Error Vsci1err 0xFFE0:0xFFE1 SPI Vspi 0xFFE2:0xFFE3 TPM2 Overflow Vtpm2ovf 0xFFE4:0xFFE5 TPM2 Channel 1 Vtpm2ch1 0xFFE6:0xFFE7 TPM2 Channel 0 Vtpm2ch0 0xFFE8:0xFFE9 TPM1 Overflow Vtpm1ovf 0xFFEA:0xFFEB TPM1 Channel 5 Vtpm1ch5 0xFFEC:0xFFED TPM1 Channel 4 Vtpm1ch4 0xFFEE:0xFFEF TPM1 Channel 3 Vtpm1ch3 0xFFF0:0xFFF1 TPM1 Channel 2 Vtpm1ch2 0xFFF2:0xFFF3 TPM1 Channel 1 Vtpm1ch1 0xFFF4:0xFFF5 TPM1 Channel 0 Vtpm1ch0 0xFFF6:0xFFF7 MCG Loss of lock Vlol 0xFFF8:0xFFF9 Low-Voltage Detect Vlvd 0xFFFA:0xFFFB IRQ Virq 0xFFFC:0xFFFD SWI Vswi 0xFFFE:0xFFFF Reset Vreset MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 43 Chapter 4 Memory 4.3 Register Addresses and Bit Assignments The registers in the MC9S08DZ60 Series are divided into these groups: * Direct-page registers are located in the first 128 locations in the memory map; these are accessible with efficient direct addressing mode instructions. * High-page registers are used much less often, so they are located above 0x1800 in the memory map. This leaves more room in the direct page for more frequently used registers and RAM. * The nonvolatile register area consists of a block of 16 locations in Flash memory at 0xFFB0-0xFFBF. Nonvolatile register locations include: -- NVPROT and NVOPT are loaded into working registers at reset -- An 8-byte backdoor comparison key that optionally allows a user to gain controlled access to secure memory Because the nonvolatile register locations are Flash memory, they must be erased and programmed like other Flash memory locations. Direct-page registers can be accessed with efficient direct addressing mode instructions. Bit manipulation instructions can be used to access any bit in any direct-page register. Table 4-2 is a summary of all user-accessible direct-page registers and control bits. The direct page registers in Table 4-2 can use the more efficient direct addressing mode, which requires only the lower byte of the address. Because of this, the lower byte of the address in column one is shown in bold text. In Table 4-3 and Table 4-5, the whole address in column one is shown in bold. In Table 4-2, Table 4-3, and Table 4-5, the register names in column two are shown in bold to set them apart from the bit names to the right. Cells that are not associated with named bits are shaded. A shaded cell with a 0 indicates this unused bit always reads as a 0. Shaded cells with dashes indicate unused or reserved bit locations that could read as 1s or 0s. MC9S08DZ60 Series Data Sheet, Rev. 4 44 Freescale Semiconductor Chapter 4 Memory Table 4-2. Direct-Page Register Summary (Sheet 1 of 3) Address Register Name 0x0000 0x0001 0x0002 0x0003 0x0004 0x0005 0x0006 0x0007 0x0008 0x0009 0x000A PTAD PTADD PTBD PTBDD PTCD PTCDD PTDD PTDDD PTED PTEDD PTFD 0x000B 0x000C 0x000D 0x000E 0x000F 0x0010 0x0011 0x0012 0x0013 0x0014 0x0015 0x0016 0x0017 0x0018 0x0019 0x001A- 0x001B 0x001C 0x001D- 0x001F 0x0020 0x0021 0x0022 0x0023 0x0024 0x0025 0x0026 0x0027 PTFDD PTGD PTGDD ACMP1SC ACMP2SC ADCSC1 ADCSC2 ADCRH ADCRL ADCCVH ADCCVL ADCCFG APCTL1 APCTL2 APCTL3 Bit 7 6 5 4 3 2 1 Bit 0 PTAD7 PTAD6 PTAD5 PTAD4 PTAD3 PTAD2 PTAD1 PTAD0 PTADD7 PTADD6 PTADD5 PTADD4 PTADD3 PTADD2 PTADD1 PTADD0 PTBD7 PTBD6 PTBD5 PTBD4 PTBD3 PTBD2 PTBD1 PTBD0 PTBDD7 PTBDD6 PTBDD5 PTBDD4 PTBDD3 PTBDD2 PTBDD1 PTBDD0 PTCD7 PTCD6 PTCD5 PTCD4 PTCD3 PTCD2 PTCD1 PTCD0 PTCDD7 PTCDD6 PTCDD5 PTCDD4 PTCDD3 PTCDD2 PTCDD1 PTCDD0 PTDD7 PTDD6 PTDD5 PTDD4 PTDD3 PTDD2 PTDD1 PTDD0 PTDDD7 PTDDD6 PTDDD5 PTDDD4 PTDDD3 PTDDD2 PTDDD1 PTDDD0 PTED7 PTED6 PTED5 PTED4 PTED3 PTED2 PTED1 PTED0 PTEDD7 PTEDD6 PTEDD5 PTEDD4 PTEDD3 PTEDD2 PTEDD1 PTEDD0 PTFD7 PTFD6 PTFD5 PTFD4 PTFD3 PTFD2 PTFD1 PTFD0 PTFDD7 PTFDD6 PTFDD5 PTFDD4 PTFDD3 PTFDD2 PTFDD1 PTFDD0 0 0 PTGD5 PTGD4 PTGD3 PTGD2 PTGD1 PTGD0 0 0 PTGDD5 PTGDD4 PTGDD3 PTGDD2 PTGDD1 PTGDD0 ACME ACBGS ACF ACIE ACO ACOPE ACMOD1 ACMOD0 ACME ACBGS ACF ACIE ACO ACOPE ACMOD1 ACMOD0 COCO AIEN ADCO ADACT ADTRG ACFE ACFGT 0 0 -- -- 0 0 0 0 ADR11 ADR10 ADR9 ADR8 ADR7 ADR6 ADR5 ADR4 ADR3 ADR2 ADR1 ADR0 0 0 0 0 ADCV11 ADCV10 ADCV9 ADCV8 ADCV7 ADCV6 ADCV4 ADCV3 ADCV2 ADCV1 ADCV0 ADLPC ADCV5 ADIV ADCH ADLSMP MODE ADICLK ADPC7 ADPC6 ADPC5 ADPC4 ADPC3 ADPC2 ADPC1 ADPC0 ADPC15 ADPC14 ADPC13 ADPC12 ADPC11 ADPC10 ADPC9 ADPC8 ADPC23 ADPC22 ADPC21 ADPC20 ADPC19 ADPC18 ADPC17 ADPC16 Reserved -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- IRQSC 0 IRQPDD IRQEDG IRQPE IRQF IRQACK IRQIE IRQMOD Reserved -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- TPM1SC TPM1CNTH TPM1CNTL TPM1MODH TPM1MODL TPM1C0SC TPM1C0VH TPM1C0VL TOF TOIE CPWMS CLKSB CLKSA PS2 PS1 PS0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 CH0F CH0IE MS0B MS0A ELS0B ELS0A 0 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 45 Chapter 4 Memory Table 4-2. Direct-Page Register Summary (Sheet 2 of 3) Address Register Name Bit 7 6 5 4 3 2 1 Bit 0 0x0028 0x0029 0x002A 0x002B 0x002C 0x002D 0x002E 0x002F 0x0030 0x0031 0x0032 TPM1C1SC TPM1C1VH TPM1C1VL TPM1C2SC TPM1C2VH TPM1C2VL TPM1C3SC TPM1C3VH TPM1C3VL TPM1C4SC TPM1C4VH CH1F CH1IE MS1B MS1A ELS1B ELS1A 0 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 CH2F CH2IE MS2B MS2A ELS2B ELS2A 0 0 Bit 15 14 13 12 11 10 9 Bit 8 0x0033 0x0034 0x0035 0x0036 0x0037 0x0038 0x0039 0x003A 0x003B 0x003C 0x003D 0x003E 0x003F 0x0040 0x0041 0x0042 0x0043 0x0044 0x0045 0x0046 0x0047 0x0048 0x0049 0x004A 0x004B 0x004C 0x004D- 0x004F TPM1C4VL TPM1C5SC TPM1C5VH TPM1C5VL Reserved SCI1BDH SCI1BDL SCI1C1 SCI1C2 SCI1S1 SCI1S2 SCI1C3 SCI1D SCI2BDH SCI2BDL SCI2C1 SCI2C2 SCI2S1 SCI2S2 SCI2C3 SCI2D MCGC1 MCGC2 MCGTRM MCGSC MCGC3 Reserved Bit 7 6 5 4 3 2 1 Bit 0 CH3F CH3IE MS3B MS3A ELS3B ELS3A 0 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 CH4F CH4IE MS4B MS4A ELS4B ELS4A 0 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 CH5F CH5IE MS5B MS5A ELS5B ELS5A 0 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 -- -- -- -- -- -- -- -- LBKDIE RXEDGIE 0 SBR12 SBR11 SBR10 SBR9 SBR8 SBR7 SBR6 SBR5 SBR4 SBR3 SBR2 SBR1 SBR0 LOOPS SCISWAI RSRC M WAKE ILT PE PT TIE TCIE RIE ILIE TE RE RWU SBK TDRE TC RDRF IDLE OR NF FE PF LBKDIF RXEDGIF 0 RXINV RWUID BRK13 LBKDE RAF R8 T8 TXDIR TXINV ORIE NEIE FEIE PEIE Bit 7 6 5 4 3 2 1 Bit 0 LBKDIE RXEDGIE 0 SBR12 SBR11 SBR10 SBR9 SBR8 SBR7 SBR6 SBR5 SBR4 SBR3 SBR2 SBR1 SBR0 LOOPS SCISWAI RSRC M WAKE ILT PE PT TIE TCIE RIE ILIE TE RE RWU SBK TDRE TC RDRF IDLE OR NF FE PF LBKDIF RXEDGIF 0 RXINV RWUID BRK13 LBKDE RAF R8 T8 TXDIR TXINV ORIE NEIE FEIE PEIE Bit 7 6 5 4 3 2 1 Bit 0 IREFS IRCLKEN IREFSTEN EREFS ERCLKEN EREFSTEN CLKS RDIV BDIV RANGE HGO LP TRIM LOLS LOCK PLLST IREFST LOLIE PLLS CME 0 -- -- -- -- -- -- -- -- CLKST OSCINIT FTRIM VDIV -- -- -- -- -- -- -- -- MC9S08DZ60 Series Data Sheet, Rev. 4 46 Freescale Semiconductor Chapter 4 Memory Table 4-2. Direct-Page Register Summary (Sheet 3 of 3) Address Register Name 0x0050 0x0051 0x0052 0x0053 0x0054 0x0055 0x0056- 0x0057 SPIC1 SPIC2 SPIBR SPIS Reserved SPID 0x0058 0x0059 0x005A 0x005B 0x005C 0x005D 0x005E- 0x005F 0x0060 0x0061 0x0062 0x0063 0x0064 0x0065 0x0066 0x0067 0x0068 0x0069 0x006A 0x006B 0x006C 0x006D 0x006E 0x006F 0x0070- 0x007F Bit 7 6 5 4 3 2 1 Bit 0 SPIE SPE SPTIE MSTR CPOL CPHA SSOE LSBFE 0 0 0 MODFEN BIDIROE 0 SPISWAI SPC0 0 SPPR2 SPPR1 SPPR0 0 SPR2 SPR1 SPR0 SPRF 0 SPTEF MODF 0 0 0 0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- IICA IICF AD7 AD6 AD5 AD4 AD3 AD2 AD1 0 IICC1 IICS IICD IICC2 IICEN IICIE MST TX TXAK RSTA 0 0 TCF IAAS BUSY ARBL 0 SRW IICIF RXAK Reserved Reserved TPM2SC TPM2CNTH TPM2CNTL TPM2MODH TPM2MODL TPM2C0SC TPM2C0VH TPM2C0VL TPM2C1SC TPM2C1VH TPM2C1VL Reserved RTCSC RTCCNT RTCMOD Reserved Reserved MULT ICR DATA GCAEN ADEXT 0 0 0 AD10 AD9 AD8 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- TOF TOIE CPWMS CLKSB CLKSA PS2 PS1 PS0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 CH0F CH0IE MS0B MS0A ELS0B ELS0A 0 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 CH1F CH1IE MS1B MS1A ELS1B ELS1A 0 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 -- -- -- -- -- -- -- RTIF -- RTCLKS RTIE RTCPS RTCCNT RTCMOD -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- High-page registers, shown in Table 4-3, are accessed much less often than other I/O and control registers so they have been located outside the direct addressable memory space, starting at 0x1800. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 47 Chapter 4 Memory Table 4-3. High-Page Register Summary (Sheet 1 of 3) Address 0x1800 0x1801 0x1802 0x1803 0x1804 - 0x1805 0x1806 0x1807 0x1808 0x1809 0x180A 0x180B- 0x180F 0x1810 0x1811 0x1812 0x1813 0x1814 0x1815 0x1816 0x1817 0x1818 0x1819- 0x181F 0x1820 0x1821 0x1822 0x1823 0x1824 0x1825 0x1826 0x1827- 0x183F 0x1840 0x1841 0x1842 0x1843 0x1844 0x1845 0x1846 Register Name SRS SBDFR SOPT1 SOPT2 Reserved SDIDH SDIDL Reserved SPMSC1 SPMSC2 Reserved DBGCAH DBGCAL DBGCBH DBGCBL DBGFH DBGFL DBGC DBGT DBGS Reserved FCDIV FOPT Reserved FCNFG FPROT FSTAT FCMD Reserved PTAPE PTASE PTADS Reserved PTASC PTAPS PTAES Bit 7 6 5 4 3 2 1 POR PIN COP ILOP ILAD LOCS LVD 0 0 0 0 0 0 0 0 BDFR STOPE SCI2PS IICPS 0 0 0 COPT Bit 0 COPCLKS COPW 0 ADHTS 0 MCSEL -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- ID11 ID10 ID9 ID8 ID7 ID6 ID5 ID4 ID3 ID2 ID1 ID0 -- -- -- -- -- -- -- -- LVWF LVWACK LVWIE LVDRE LVDSE LVDE 0 BGBE 0 0 LVDV LVWV PPDF PPDACK 0 PPDC -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 DBGEN ARM TAG BRKEN RWA RWAEN RWB RWBEN TRGSEL BEGIN 0 0 TRG3 TRG2 TRG1 TRG0 AF BF ARMF 0 CNT3 CNT2 CNT1 CNT0 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- DIVLD PRDIV8 KEYEN FNORED EPGMOD 0 0 0 -- -- -- -- -- -- -- -- KEYACC Reserved1 0 0 0 1 0 FBLANK 0 0 0 EPGSEL DIV EPS FCBEF SEC FPS FCCF FPVIOL FACCERR FCMD -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- PTAPE7 PTAPE6 PTAPE5 PTAPE4 PTAPE3 PTAPE2 PTAPE1 PTAPE0 PTASE7 PTASE6 PTASE5 PTASE4 PTASE3 PTASE2 PTASE1 PTASE0 PTADS7 PTADS6 PTADS5 PTADS4 PTADS3 PTADS2 PTADS1 PTADS0 -- -- -- -- -- -- -- -- 0 0 0 0 PTAIF PTAACK PTAIE PTAMOD PTAPS7 PTAPS6 PTAPS5 PTAPS4 PTAPS3 PTAPS2 PTAPS1 PTAPS0 PTAES7 PTAES6 PTAES5 PTAES4 PTAES3 PTAES2 PTAES1 PTAES0 MC9S08DZ60 Series Data Sheet, Rev. 4 48 Freescale Semiconductor Chapter 4 Memory Table 4-3. High-Page Register Summary (Sheet 2 of 3) Address 0x1847 0x1848 0x1849 0x184A 0x184B 0x184C 0x184D 0x184E 0x184F 0x1850 0x1851 0x1852 0x1853- 0x1857 0x1858 0x1859 0x185A 0x185B 0x185C 0x185D 0x185E 0x185F 0x1860 0x1861 0x1862 0x1863- 0x1867 0x1868 0x1869 0x186A 0x186B- 0x186F 0x1870 0x1871 0x1872 0x1873- 0x187F 0x1880 0x1881 0x1882 Register Name Reserved PTBPE PTBSE PTBDS Reserved PTBSC PTBPS PTBES Reserved PTCPE PTCSE PTCDS Reserved PTDPE PTDSE PTDDS Reserved PTDSC PTDPS PTDES Reserved PTEPE PTESE PTEDS Reserved PTFPE PTFSE PTFDS Reserved PTGPE PTGSE PTGDS Reserved CANCTL0 CANCTL1 CANBTR0 Bit 7 6 5 4 3 2 1 Bit 0 -- -- -- -- -- -- -- -- PTBPE7 PTBPE6 PTBPE5 PTBPE4 PTBPE3 PTBPE2 PTBPE1 PTBPE0 PTBSE7 PTBSE6 PTBSE5 PTBSE4 PTBSE3 PTBSE2 PTBSE1 PTBSE0 PTBDS7 PTBDS6 PTBDS5 PTBDS4 PTBDS3 PTBDS2 PTBDS1 PTBDS0 -- -- -- -- -- -- -- -- 0 0 0 0 PTBIF PTBACK PTBIE PTBMOD PTBPS7 PTBPS6 PTBPS5 PTBPS4 PTBPS3 PTBPS2 PTBPS1 PTBPS0 PTBES7 PTBES6 PTBES5 PTBES4 PTBES3 PTBES2 PTBES1 PTBES0 -- -- -- -- -- -- -- -- PTCPE7 PTCPE6 PTCPE5 PTCPE4 PTCPE3 PTCPE2 PTCPE1 PTCPE0 PTCSE7 PTCSE6 PTCSE5 PTCSE4 PTCSE3 PTCSE2 PTCSE1 PTCSE0 PTCDS7 PTCDS6 PTCDS5 PTCDS4 PTCDS3 PTCDS2 PTCDS1 PTCDS0 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- PTDPE7 PTDPE6 PTDPE5 PTDPE4 PTDPE3 PTDPE2 PTDPE1 PTDPE0 PTDSE7 PTDSE6 PTDSE5 PTDSE4 PTDSE3 PTDSE2 PTDSE1 PTDSE0 PTDDS7 PTDDS6 PTDDS5 PTDDS4 PTDDS3 PTDDS2 PTDDS1 PTDDS0 -- -- -- -- -- -- -- -- 0 0 0 0 PTDIF PTDACK PTDIE PTDMOD PTDPS7 PTDPS6 PTDPS5 PTDPS4 PTDPS3 PTDPS2 PTDPS1 PTDPS0 PTDES7 PTDES6 PTDES5 PTDES4 PTDES3 PTDES2 PTDES1 PTDES0 -- -- -- -- -- -- -- -- PTEPE7 PTEPE6 PTEPE5 PTEPE4 PTEPE3 PTEPE2 PTEPE1 PTEPE0 PTESE7 PTESE6 PTESE5 PTESE4 PTESE3 PTESE2 PTESE1 PTESE0 PTEDS7 PTEDS6 PTEDS5 PTEDS4 PTEDS3 PTEDS2 PTEDS1 PTEDS0 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- PTFPE7 PTFPE6 PTFPE5 PTFPE4 PTFPE3 PTFPE2 PTFPE1 PTFPE0 PTFSE7 PTFSE6 PTFSE5 PTFSE4 PTFSE3 PTFSE2 PTFSE1 PTFSE0 PTFDS7 PTFDS6 PTFDS5 PTFDS4 PTFDS3 PTFDS2 PTFDS1 PTFDS0 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 0 0 PTGPE5 PTGPE4 PTGPE3 PTGPE2 PTGPE1 PTGPE0 0 0 PTGSE5 PTGSE4 PTGSE3 PTGSE2 PTGSE1 PTGSE0 0 0 PTGDS5 PTGDS4 PTGDS3 PTGDS2 PTGDS1 PTGDS0 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- RXFRM RXACT CSWAI SYNCH TIME WUPE SLPRQ INITRQ CANE CLKSRC LOOPB LISTEN BORM WUPM SLPAK INITAK SJW1 SJW0 BRP5 BRP4 BRP3 BRP2 BRP1 BRP0 MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 49 Chapter 4 Memory Table 4-3. High-Page Register Summary (Sheet 3 of 3) Address Register Name 0x1883 0x1884 0x1885 0x1886 0x1887 0x1888 0x1889 0x188A 0x188B 0x188C 0x188D 0x188E CANBTR1 CANRFLG CANRIER CANTFLG CANTIER CANTARQ CANTAAK CANTBSEL CANIDAC Reserved CANMISC CANRXERR 0x188F 0x1890 - 0x1893 0x1894 - 0x1897 0x1898 - 0x189B 0x189C- 0x189F 0x18BE 0x18BF 0x18C0- 0x18FF CANTXERR CANIDAR0 - CANIDAR3 CANIDMR0 - CANIDMR3 CANIDAR4 - CANIDAR7 CANIDMR4 - CANIDMR7 CANTTSRH CANTTSRL 1 Reserved Bit 7 6 5 4 3 2 1 Bit 0 SAMP TSEG22 TSEG21 TSEG20 TSEG13 TSEG12 TSEG11 TSEG10 WUPIF CSCIF RSTAT1 RSTAT0 TSTAT1 TSTAT0 OVRIF RXF WUPIE CSCIE RSTATE1 RSTATE0 TSTATE1 TSTATE0 OVRIE RXFIE 0 0 0 0 0 TXE2 TXE1 TXE0 0 0 0 0 0 TXEIE2 TXEIE1 TXEIE0 0 0 0 0 0 ABTRQ2 ABTRQ1 ABTRQ0 0 0 0 0 0 ABTAK2 ABTAK1 ABTAK0 0 0 0 0 0 TX2 TX1 TX0 0 0 IDAM1 IDAM0 0 IDHIT2 IDHIT1 IDHIT0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 BOHOLD RXERR7 RXERR6 RXERR5 RXERR4 RXERR3 RXERR2 RXERR1 RXERR0 TXERR7 TXERR6 TXERR5 TXERR4 TXERR3 TXERR2 TXERR1 TXERR0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 TSR15 TSR14 TSR13 TSR12 TSR11 TSR10 TSR9 TSR8 TSR7 TSR6 TSR5 TSR4 TSR3 TSR2 TSR1 TSR0 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- This bit is reserved. User must write a 1 to this bit. Failing to do so may result in unexpected behavior. Figure 4-4 shows the structure of receive and transmit buffers for extended identifier mapping. These registers vary depending on whether standard or extended mapping is selected. See Chapter 12, "Freescale Controller Area Network (S08MSCANV1)," for details on extended and standard identifier mapping. Table 4-4. MSCAN Foreground Receive and Transmit Buffer Layouts -- Extended Mapping Shown 0x18A0 0x18A1 0x18A2 0x18A3 0x18A4 - 0x18AB 0x18AC 0x18AD 0x18AE CANRIDR0 CANRIDR1 CANRIDR2 CANRIDR3 CANRDSR0 - CANRDSR7 CANRDLR Reserved CANRTSRH ID28 ID27 ID26 ID25 ID24 ID23 ID22 ID21 IDE(1) ID20 ID19 ID18 SRR(1) ID17 ID16 ID15 ID14 ID13 ID12 ID11 ID10 ID9 ID8 ID7 ID6 ID5 ID4 ID3 ID2 ID1 ID0 RTR2 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 -- -- -- -- DLC3 DLC2 DLC1 DLC0 -- -- -- -- -- -- -- -- TSR15 TSR14 TSR13 TSR12 TSR11 TSR10 TSR9 TSR8 MC9S08DZ60 Series Data Sheet, Rev. 4 50 Freescale Semiconductor Chapter 4 Memory Table 4-4. MSCAN Foreground Receive and Transmit Buffer Layouts -- Extended Mapping Shown 0x18AF 0x18B0 0x18B1 0x18B2 0x18B3 0x18B4 - 0x18BB 0x18BC 0x18BD 1 2 CANRTSRL CANTIDR0 CANTIDR1 CANTIDR2 CANTIDR3 CANTDSR0 - CANTDSR7 CANTDLR CANTTBPR TSR7 TSR6 TSR5 TSR4 TSR3 TSR2 TSR1 TSR0 ID10 ID9 ID8 ID7 ID6 ID5 ID4 ID3 ID2 ID1 ID0 RTR IDE -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 -- -- -- -- DLC3 DLC2 DLC1 DLC0 PRIO7 PRIO6 PRIO5 PRIO4 PRIO3 PRIO2 PRIO1 PRIO0 SRR and IDE are both 1s. The position of RTR differs between extended and standard identifier mapping. Nonvolatile Flash registers, shown in Table 4-5, are located in the Flash memory. These registers include an 8-byte backdoor key, NVBACKKEY, which can be used to gain access to secure memory resources. During reset events, the contents of NVPROT and NVOPT in the nonvolatile register area of the Flash memory are transferred into corresponding FPROT and FOPT working registers in the high-page registers to control security and block protection options. Table 4-5. Nonvolatile Register Summary Address Register Name Bit 7 6 5 4 3 2 1 Bit 0 0xFFAE Reserved for storage of FTRIM 0 0 0 0 0 0 0 FTRIM 0xFFAF Res. for storage of MCGTRM 0xFFB0- 0xFFB7 0xFFB8- 0xFFBC 0xFFBD 0xFFBE 0xFFBF NVBACKKEY -- -- -- -- -- -- -- -- Reserved NVPROT Reserved NVOPT TRIM 8-Byte Comparison Key -- -- -- -- -- -- -- -- -- -- EPS FPS -- -- -- -- -- -- KEYEN FNORED EPGMOD 0 0 0 SEC Provided the key enable (KEYEN) bit is 1, the 8-byte comparison key can be used to temporarily disengage memory security. This key mechanism can be accessed only through user code running in secure memory. (A security key cannot be entered directly through background debug commands.) This security key can be disabled completely by programming the KEYEN bit to 0. If the security key is disabled, the only way to disengage security is by mass erasing the Flash if needed (normally through the background debug interface) and verifying that Flash is blank. To avoid returning to secure mode after the next reset, program the security bits (SEC) to the unsecured state (1:0). MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 51 Chapter 4 Memory 4.4 RAM The MC9S08DZ60 Series includes static RAM. The locations in RAM below 0x0100 can be accessed using the more efficient direct addressing mode, and any single bit in this area can be accessed with the bit manipulation instructions (BCLR, BSET, BRCLR, and BRSET). Locating the most frequently accessed program variables in this area of RAM is preferred. The RAM retains data while the MCU is in low-power wait, stop2, or stop3 mode. At power-on the contents of RAM are uninitialized. RAM data is unaffected by any reset if the supply voltage does not drop below the minimum value for RAM retention (VRAM). For compatibility with M68HC05 MCUs, the HCS08 resets the stack pointer to 0x00FF. In the MC9S08DZ60 Series, it is usually best to reinitialize the stack pointer to the top of the RAM so the direct page RAM can be used for frequently accessed RAM variables and bit-addressable program variables. Include the following 2-instruction sequence in your reset initialization routine (where RamLast is equated to the highest address of the RAM in the Freescale Semiconductor equate file). LDHX TXS #RamLast+1 ;point one past RAM ;SP<-(H:X-1) When security is enabled, the RAM is considered a secure memory resource and is not accessible through BDM or code executing from non-secure memory. See Section 4.5.9, "Security", for a detailed description of the security feature. 4.5 Flash and EEPROM MC9S08DZ60 Series devices include Flash and EEPROM memory intended primarily for program and data storage. In-circuit programming allows the operating program and data to be loaded into Flash and EEPROM, respectively, after final assembly of the application product. It is possible to program the arrays through the single-wire background debug interface. Because no special voltages are needed for erase and programming operations, in-application programming is also possible through other software-controlled communication paths. For a more detailed discussion of in-circuit and in-application programming, refer to the HCS08 Family Reference Manual, Volume I, Freescale Semiconductor document order number HCS08RMv1. 4.5.1 Features Features of the Flash and EEPROM memory include: * Array size (see Table 1-1 for exact array sizes) * Flash sector size: 768 bytes * EEPROM sector size: selectable 4-byte or 8-byte sector mapping operation * Single power supply program and erase * Command interface for fast program and erase operation * Up to 100,000 program/erase cycles at typical voltage and temperature * Flexible block protection and vector redirection * Security feature for Flash, EEPROM, and RAM MC9S08DZ60 Series Data Sheet, Rev. 4 52 Freescale Semiconductor Chapter 4 Memory * * 4.5.2 Burst programming capability Sector erase abort Program and Erase Times Before any program or erase command can be accepted, the Flash and EEPROM clock divider register (FCDIV) must be written to set the internal clock for the Flash and EEPROM module to a frequency (fFCLK) between 150 kHz and 200 kHz (see Section 4.5.11.1, "Flash and EEPROM Clock Divider Register (FCDIV)"). This register can be written only once, so normally this write is performed during reset initialization. The user must ensure that FACCERR is not set before writing to the FCDIV register. One period of the resulting clock (1/fFCLK) is used by the command processor to time program and erase pulses. An integer number of these timing pulses is used by the command processor to complete a program or erase command. Table 4-6 shows program and erase times. The bus clock frequency and FCDIV determine the frequency of FCLK (fFCLK). The time for one cycle of FCLK is tFCLK = 1/fFCLK. The times are shown as a number of cycles of FCLK and as an absolute time for the case where tFCLK = 5 s. Program and erase times shown include overhead for the command state machine and enabling and disabling of program and erase voltages. Table 4-6. Program and Erase Times 1 4.5.3 Parameter Cycles of FCLK Time if FCLK = 200 kHz Byte program 9 45 s Burst program 4 20 s1 Sector erase 4000 20 ms Mass erase 20,000 100 ms Sector erase abort 4 20 s1 Excluding start/end overhead Program and Erase Command Execution The FCDIV register must be initialized after any reset and any error flag is cleared before beginning command execution. The command execution steps are: 1. Write a data value to an address in the Flash or EEPROM array. The address and data information from this write is latched into the Flash and EEPROM interface. This write is a required first step in any command sequence. For erase and blank check commands, the value of the data is not important. For sector erase commands, the address can be any address in the sector of Flash or EEPROM to be erased. For mass erase and blank check commands, the address can be any address in the Flash or EEPROM memory. Flash and EEPROM erase independently of each other. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 53 Chapter 4 Memory NOTE Before programming a particular byte in the Flash or EEPROM, the sector in which that particular byte resides must be erased by a mass or sector erase operation. Reprogramming bits in an already programmed byte without first performing an erase operation may disturb data stored in the Flash or EEPROM memory. 2. Write the command code for the desired command to FCMD. The six valid commands are blank check (0x05), byte program (0x20), burst program (0x25), sector erase (0x40), mass erase1 (0x41), and sector erase abort (0x47). The command code is latched into the command buffer. 3. Write a 1 to the FCBEF bit in FSTAT to clear FCBEF and launch the command (including its address and data information). A partial command sequence can be aborted manually by writing a 0 to FCBEF any time after the write to the memory array and before writing the 1 that clears FCBEF and launches the complete command. Aborting a command in this way sets the FACCERR access error flag which must be cleared before starting a new command. A strictly monitored procedure must be obeyed or the command will not be accepted. This minimizes the possibility of any unintended changes to the memory contents. The command complete flag (FCCF) indicates when a command is complete. The command sequence must be completed by clearing FCBEF to launch the command. Figure 4-2 is a flowchart for executing all of the commands except for burst programming and sector erase abort. 4. Wait until the FCCF bit in FSTAT is set. As soon as FCCF= 1, the operation has completed successfully. 1. A mass erase is possible only when the Flash block is fully unprotected. MC9S08DZ60 Series Data Sheet, Rev. 4 54 Freescale Semiconductor Chapter 4 Memory (1) Required only once WRITE TO FCDIV(1) after reset. PROGRAM AND ERASE FLOW START 0 FACCERR? CLEAR ERROR WRITE TO FLASH OR EEPROM TO BUFFER ADDRESS AND DATA WRITE COMMAND TO FCMD WRITE 1 TO FCBEF TO LAUNCH COMMAND AND CLEAR FCBEF (2) FPVIOL OR FACCERR? (2) Wait at least four bus cycles before checking FCBEF or FCCF. YES ERROR EXIT NO 0 FCCF? 1 DONE Figure 4-2. Program and Erase Flowchart 4.5.4 Burst Program Execution The burst program command is used to program sequential bytes of data in less time than would be required using the standard program command. This is possible because the high voltage to the Flash array does not need to be disabled between program operations. Ordinarily, when a program or erase command is issued, an internal charge pump associated with the Flash memory must be enabled to supply high voltage to the array. Upon completion of the command, the charge pump is turned off. When a burst program command is issued, the charge pump is enabled and remains enabled after completion of the burst program operation if these two conditions are met: * The next burst program command sequence has begun before the FCCF bit is set. * The next sequential address selects a byte on the same burst block as the current byte being programmed. A burst block in this Flash memory consists of 32 bytes. A new burst block begins at each 32-byte address boundary. The first byte of a series of sequential bytes being programmed in burst mode will take the same amount of time to program as a byte programmed in standard mode. Subsequent bytes will program in the burst MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 55 Chapter 4 Memory program time provided that the conditions above are met. If the next sequential address is the beginning of a new row, the program time for that byte will be the standard time instead of the burst time. This is because the high voltage to the array must be disabled and then enabled again. If a new burst command has not been queued before the current command completes, then the charge pump will be disabled and high voltage removed from the array. A flowchart to execute the burst program operation is shown in Figure 4-3. (1) Required only once WRITE TO FCDIV(1) BURST PROGRAM FLOW after reset. START 0 FACCERR? 1 CLEAR ERROR FCBEF? 0 1 WRITE TO Flash TO BUFFER ADDRESS AND DATA WRITE COMMAND TO FCMD WRITE 1 TO FCBEF TO LAUNCH COMMAND AND CLEAR FCBEF (2) FPVIOL OR FACCERR? (2) Wait at least four bus cycles before checking FCBEF or FCCF. YES ERROR EXIT NO YES NEW BURST COMMAND? NO 0 FCCF? 1 DONE Figure 4-3. Burst Program Flowchart MC9S08DZ60 Series Data Sheet, Rev. 4 56 Freescale Semiconductor Chapter 4 Memory 4.5.5 Sector Erase Abort The sector erase abort operation will terminate the active sector erase operation so that other sectors are available for read and program operations without waiting for the sector erase operation to complete. The sector erase abort command write sequence is as follows: 1. Write to any Flash or EEPROM address to start the command write sequence for the sector erase abort command. The address and data written are ignored. 2. Write the sector erase abort command, 0x47, to the FCMD register. 3. Clear the FCBEF flag in the FSTAT register by writing a 1 to FCBEF to launch the sector erase abort command. If the sector erase abort command is launched resulting in the early termination of an active sector erase operation, the FACCERR flag will set once the operation completes as indicated by the FCCF flag being set. The FACCERR flag sets to inform the user that the Flash sector may not be fully erased and a new sector erase command must be launched before programming any location in that specific sector. If the sector erase abort command is launched but the active sector erase operation completes normally, the FACCERR flag will not set upon completion of the operation as indicated by the FCCF flag being set. Therefore, if the FACCERR flag is not set after the sector erase abort command has completed, a sector being erased when the abort command was launched will be fully erased. A flowchart to execute the sector erase abort operation is shown in Figure 4-4. SECTOR ERASE ABORT FLOW START 1 FCCF? 0 WRITE TO Flash TO BUFFER ADDRESS AND DATA WRITE 0x47 TO FCMD WRITE 1 TO FCBEF TO LAUNCH COMMAND AND CLEAR FCBEF (2) (2) Wait at least four bus cycles before checking FCBEF or FCCF. 0 FCCF? 1 SECTOR ERASE COMPLETED 0 FACCERR? 1 SECTOR ERASE ABORTED Figure 4-4. Sector Erase Abort Flowchart MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 57 Chapter 4 Memory NOTE The FCBEF flag will not set after launching the sector erase abort command. If an attempt is made to start a new command write sequence with a sector erase abort operation active, the FACCERR flag in the FSTAT register will be set. A new command write sequence may be started after clearing the ACCERR flag, if set. NOTE The sector erase abort command should be used sparingly since a sector erase operation that is aborted counts as a complete program/erase cycle. 4.5.6 Access Errors An access error occurs whenever the command execution protocol is violated. Any of the following specific actions will cause the access error flag (FACCERR) in FSTAT to be set. FACCERR must be cleared by writing a 1 to FACCERR in FSTAT before any command can be processed. * Writing to a Flash address before the internal Flash and EEPROM clock frequency has been set by writing to the FCDIV register. * Writing to a Flash address while FCBEF is not set. (A new command cannot be started until the command buffer is empty.) * Writing a second time to a Flash address before launching the previous command. (There is only one write to Flash for every command.) * Writing a second time to FCMD before launching the previous command. (There is only one write to FCMD for every command.) * Writing to any Flash control register other than FCMD after writing to a Flash address. * Writing any command code other than the six allowed codes (0x05, 0x20, 0x25, 0x40, 0x41, or 0x47) to FCMD. * Writing any Flash control register other than to write to FSTAT (to clear FCBEF and launch the command) after writing the command to FCMD. * The MCU enters stop mode while a program or erase command is in progress. (The command is aborted.) * Writing the byte program, burst program, sector erase or sector erase abort command code (0x20, 0x25, 0x40, or 0x47) with a background debug command while the MCU is secured. (The background debug controller can do blank check and mass erase commands only when the MCU is secure.) * Writing 0 to FCBEF to cancel a partial command. MC9S08DZ60 Series Data Sheet, Rev. 4 58 Freescale Semiconductor Chapter 4 Memory 4.5.7 Block Protection The block protection feature prevents the protected region of Flash or EEPROM from program or erase changes. Block protection is controlled through the Flash and EEPROM protection register (FPROT). The EPS bits determine the protected region of EEPROM and the FPS bits determine the protected region of Flash. See Section 4.5.11.4, "Flash and EEPROM Protection Register (FPROT and NVPROT)." After exit from reset, FPROT is loaded with the contents of the NVPROT location, which is in the nonvolatile register block of the Flash memory. Any FPROT write that attempts to decrease the size of the protected region will be ignored. Because NVPROT is within the last sector of Flash, if any amount of memory is protected, NVPROT is itself protected and cannot be unprotected (intentionally or unintentionally) by the application software. FPROT can be written through background debug commands, which provides a way to erase and reprogram protected Flash memory. One use for block protection is to block protect an area of Flash memory for a bootloader program. this bootloader program can call a routine outside of Flash that can be used to sector erase the rest of the Flash memory and reprogram it. The bootloader is protected even if MCU power is lost during an erase and reprogram operation. 4.5.8 Vector Redirection While any Flash is block protected, the reset and interrupt vectors will be protected. Vector redirection allows users to modify interrupt vector information without unprotecting bootloader and reset vector space. Vector redirection is enabled by programming the FNORED bit in the NVOPT register located at address 0xFFBF to 0. For redirection to occur, at least some portion of the Flash memory must be block protected by programming the NVPROT register located at address 0xFFBD. All interrupt vectors (memory locations 0xFFC0-0xFFFD) are redirected, though the reset vector (0xFFFE:0xFFFF) is not. For example, if 1536 bytes of Flash are protected, the protected address region is from 0xFA00 through 0xFFFF. The interrupt vectors (0xFFC0-0xFFFD) are redirected to the locations 0xF9C0-0xF9FD. If vector redirection is enabled and an interrupt occurs, the values in the locations 0xF9E0:0xF9E1 are used for the vector instead of the values in the locations 0xFFE0:0xFFE1. This allows the user to reprogram the unprotected portion of the Flash with new program code including new interrupt vector values while leaving the protected area, which includes the default vector locations, unchanged. 4.5.9 Security The MC9S08DZ60 Series includes circuitry to prevent unauthorized access to the contents of Flash, EEPROM, and RAM memory. When security is engaged, Flash, EEPROM, and RAM are considered secure resources. Direct-page registers, high-page registers, and the background debug controller are considered unsecured resources. Programs executing within secure memory have normal access to any MCU memory locations and resources. Attempts to access a secure memory location with a program executing from an unsecured memory space or through the background debug interface are blocked (writes are ignored and reads return all 0s). Security is engaged or disengaged based on the state of two register bits (SEC[1:0]) in the FOPT register. During reset, the contents of the nonvolatile location NVOPT are copied from Flash into the working FOPT register in high-page register space. A user engages security by programming the NVOPT location, MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 59 Chapter 4 Memory which can be performed at the same time the Flash memory is programmed. The 1:0 state disengages security; the other three combinations engage security. Notice the erased state (1:1) makes the MCU secure. During development, whenever the Flash is erased, it is good practice to immediately program the SEC0 bit to 0 in NVOPT so SEC = 1:0. This would allow the MCU to remain unsecured after a subsequent reset. The on-chip debug module cannot be enabled while the MCU is secure. The separate background debug controller can be used for background memory access commands, but the MCU cannot enter active background mode except by holding BKGD low at the rising edge of reset. A user can choose to allow or disallow a security unlocking mechanism through an 8-byte backdoor security key. If the nonvolatile KEYEN bit in NVOPT/FOPT is 0, the backdoor key is disabled and there is no way to disengage security without completely erasing all Flash locations. If KEYEN is 1, a secure user program can temporarily disengage security by: 1. Writing 1 to KEYACC in the FCNFG register. This makes the Flash module interpret writes to the backdoor comparison key locations (NVBACKKEY through NVBACKKEY+7) as values to be compared against the key rather than as the first step in a Flash program or erase command. 2. Writing the user-entered key values to the NVBACKKEY through NVBACKKEY+7 locations. These writes must be performed in order starting with the value for NVBACKKEY and ending with NVBACKKEY+7. STHX must not be used for these writes because these writes cannot be performed on adjacent bus cycles. User software normally would get the key codes from outside the MCU system through a communication interface such as a serial I/O. 3. Writing 0 to KEYACC in the FCNFG register. If the 8-byte key that was written matches the key stored in the Flash locations, SEC bits are automatically changed to 1:0 and security will be disengaged until the next reset. The security key can be written only from secure memory (either RAM, EEPROM, or Flash), so it cannot be entered through background commands without the cooperation of a secure user program. The backdoor comparison key (NVBACKKEY through NVBACKKEY+7) is located in Flash memory locations in the nonvolatile register space so users can program these locations exactly as they would program any other Flash memory location. The nonvolatile registers are in the same 768-byte block of Flash as the reset and interrupt vectors, so block protecting that space also block protects the backdoor comparison key. Block protects cannot be changed from user application programs, so if the vector space is block protected, the backdoor security key mechanism cannot permanently change the block protect, security settings, or the backdoor key. Security can always be disengaged through the background debug interface by taking these steps: 1. Disable any block protections by writing FPROT. FPROT can be written only with background debug commands, not from application software. 2. Mass erase Flash if necessary. 3. Blank check Flash. Provided Flash is completely erased, security is disengaged until the next reset. To avoid returning to secure mode after the next reset, program NVOPT so SEC = 1:0. MC9S08DZ60 Series Data Sheet, Rev. 4 60 Freescale Semiconductor Chapter 4 Memory 4.5.10 EEPROM Mapping Only half of the EEPROM is in the memory map. The EPGSEL bit in FCNFG register selects which half of the array can be accessed in foreground while the other half can not be accessed in background. There are two mapping mode options that can be selected to configure the 8-byte EEPROM sectors: 4-byte mode and 8-byte mode. Each mode is selected by the EPGMOD bit in the FOPT register. In 4-byte sector mode (EPGMOD = 0), each 8-byte sector splits four bytes on foreground and four bytes on background but on the same addresses. The EPGSEL bit selects which four bytes can be accessed. During a sector erase, the entire 8-byte sector (four bytes in foreground and four bytes in background) is erased. In 8-byte sector mode (EPGMOD = 1), each entire 8-byte sector is in a single page. The EPGSEL bit selects which sectors are on background. During a sector erase, the entire 8-byte sector in foreground is erased. 4.5.11 Flash and EEPROM Registers and Control Bits The Flash and EEPROM modules have seven 8-bit registers in the high-page register space and three locations in the nonvolatile register space in Flash memory. Two of those locations are copied into two corresponding high-page control registers at reset. There is also an 8-byte comparison key in Flash memory. Refer to Table 4-3 and Table 4-5 for the absolute address assignments for all Flash and EEPROM registers. This section refers to registers and control bits only by their names. A Freescale Semiconductor-provided equate or header file normally is used to translate these names into the appropriate absolute addresses. 4.5.11.1 Flash and EEPROM Clock Divider Register (FCDIV) Bit 7 of this register is a read-only flag. Bits 6:0 may be read at any time but can be written only one time. Before any erase or programming operations are possible, write to this register to set the frequency of the clock for the nonvolatile memory system within acceptable limits. 7 R 6 5 4 3 2 1 0 0 0 0 DIVLD PRDIV8 DIV W Reset 0 0 0 0 0 = Unimplemented or Reserved Figure 4-5. Flash and EEPROM Clock Divider Register (FCDIV) MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 61 Chapter 4 Memory Table 4-7. FCDIV Register Field Descriptions Field Description 7 DIVLD Divisor Loaded Status Flag -- When set, this read-only status flag indicates that the FCDIV register has been written since reset. Reset clears this bit and the first write to this register causes this bit to become set regardless of the data written. 0 FCDIV has not been written since reset; erase and program operations disabled for Flash and EEPROM. 1 FCDIV has been written since reset; erase and program operations enabled for Flash and EEPROM. 6 PRDIV8 5:0 DIV Prescale (Divide) Flash and EEPROM Clock by 8 (This bit is write once.) 0 Clock input to the Flash and EEPROM clock divider is the bus rate clock. 1 Clock input to the Flash and EEPROM clock divider is the bus rate clock divided by 8. Divisor for Flash and EEPROM Clock Divider -- These bits are write once. The Flash and EEPROM clock divider divides the bus rate clock (or the bus rate clock divided by 8 if PRDIV8 = 1) by the value in the 6-bit DIV field plus one. The resulting frequency of the internal Flash and EEPROM clock must fall within the range of 200 kHz to 150 kHz for proper Flash and EEPROM operations. Program/Erase timing pulses are one cycle of this internal Flash and EEPROM clock which corresponds to a range of 5 s to 6.7 s. The automated programming logic uses an integer number of these pulses to complete an erase or program operation. See Equation 4-1 and Equation 4-2. if PRDIV8 = 0 -- fFCLK = fBus / (DIV + 1) Eqn. 4-1 if PRDIV8 = 1 -- fFCLK = fBus / (8 x (DIV + 1)) Eqn. 4-2 Table 4-8 shows the appropriate values for PRDIV8 and DIV for selected bus frequencies. Table 4-8. Flash and EEPROM Clock Divider Settings 4.5.11.2 fBus PRDIV8 (Binary) DIV (Decimal) fFCLK Program/Erase Timing Pulse (5 s Min, 6.7 s Max) 20 MHz 1 12 192.3 kHz 5.2 s 10 MHz 0 49 200 kHz 5 s 8 MHz 0 39 200 kHz 5 s 4 MHz 0 19 200 kHz 5 s 2 MHz 0 9 200 kHz 5 s 1 MHz 0 4 200 kHz 5 s 200 kHz 0 0 200 kHz 5 s 150 kHz 0 0 150 kHz 6.7 s Flash and EEPROM Options Register (FOPT and NVOPT) During reset, the contents of the nonvolatile location NVOPT are copied from Flash into FOPT. To change the value in this register, erase and reprogram the NVOPT location in Flash memory as usual and then issue a new MCU reset. MC9S08DZ60 Series Data Sheet, Rev. 4 62 Freescale Semiconductor Chapter 4 Memory R 7 6 5 4 3 2 KEYEN FNORED EPGMOD 0 0 0 F F F 0 0 0 1 0 SEC W Reset = Unimplemented or Reserved F F F = loaded from nonvolatile location NVOPT during reset Figure 4-6. Flash and EEPROM Options Register (FOPT) Table 4-9. FOPT Register Field Descriptions Field Description 7 KEYEN Backdoor Key Mechanism Enable -- When this bit is 0, the backdoor key mechanism cannot be used to disengage security. The backdoor key mechanism is accessible only from user (secured) firmware. BDM commands cannot be used to write key comparison values that would unlock the backdoor key. For more detailed information about the backdoor key mechanism, refer to Section 4.5.9, "Security." 0 No backdoor key access allowed. 1 If user firmware writes an 8-byte value that matches the nonvolatile backdoor key (NVBACKKEY through NVBACKKEY+7 in that order), security is temporarily disengaged until the next MCU reset. 6 FNORED Vector Redirection Disable -- When this bit is 1, then vector redirection is disabled. 0 Vector redirection enabled. 1 Vector redirection disabled. 5 EPGMOD EEPROM Sector Mode -- When this bit is 0, each sector is split into two pages (4-byte mode). When this bit is 1, each sector is in a single page (8-byte mode). 0 Half of each EEPROM sector is in Page 0 and the other half is in Page 1. 1 Each sector is in a single page. 1:0 SEC Security State Code -- This 2-bit field determines the security state of the MCU as shown in Table 4-10. When the MCU is secure, the contents of RAM, EEPROM and Flash memory cannot be accessed by instructions from any unsecured source including the background debug interface. SEC changes to 1:0 after successful backdoor key entry or a successful blank check of Flash. For more detailed information about security, refer to Section 4.5.9, "Security." Table 4-10. Security States1 1 SEC[1:0] Description 0:0 secure 0:1 secure 1:0 unsecured 1:1 secure SEC changes to 1:0 after successful backdoor key entry or a successful blank check of Flash. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 63 Chapter 4 Memory 4.5.11.3 Flash and EEPROM Configuration Register (FCNFG) 7 R 6 5 4 EPGSEL KEYACC Reserved1 0 0 1 0 3 2 1 0 0 0 0 1 0 0 0 1 W Reset 0 = Unimplemented or Reserved Figure 4-7. Flash Configuration Register (FCNFG) 1 User must write a 1 to this bit. Failing to do so may result in unexpected behavior. Table 4-11. FCNFG Register Field Descriptions Field Description 6 EPGSEL EEPROM Page Select -- This bit selects which EEPROM page is accessed in the memory map. 0 Page 0 is in foreground of memory map. Page 1 is in background and can not be accessed. 1 Page 1 is in foreground of memory map. Page 0 is in background and can not be accessed. 5 KEYACC Enable Writing of Access Key -- This bit enables writing of the backdoor comparison key. For more detailed information about the backdoor key mechanism, refer to Section 4.5.9, "Security." 0 Writes to 0xFFB0-0xFFB7 are interpreted as the start of a Flash programming or erase command. 1 Writes to NVBACKKEY (0xFFB0-0xFFB7) are interpreted as comparison key writes. 4.5.11.4 Flash and EEPROM Protection Register (FPROT and NVPROT) The FPROT register defines which Flash and EEPROM sectors are protected against program and erase operations. During the reset sequence, the FPROT register is loaded from the nonvolatile location NVPROT. To change the protection that will be loaded during the reset sequence, the sector containing NVPROT must be unprotected and erased, then NVPROT can be reprogrammed. FPROT bits are readable at any time and writable as long as the size of the protected region is being increased. Any write to FPROT that attempts to decrease the size of the protected memory will be ignored. Trying to alter data in any protected area will result in a protection violation error and the FPVIOL flag will be set in the FSTAT register. Mass erase is not possible if any one of the sectors is protected. 7 R 6 EPS1 5 4 3 2 1 0 FPS1 W Reset 1 This register is loaded from nonvolatile location NVPROT during reset. Background commands can be used to change the contents of these bits in FPROT. Figure 4-8. Flash and EEPROM Protection Register (FPROT) MC9S08DZ60 Series Data Sheet, Rev. 4 64 Freescale Semiconductor Chapter 4 Memory Table 4-12. FPROT Register Field Descriptions Field Description 7:6 EPS EEPROM Protect Select Bits -- This 2-bit field determines the protected EEPROM locations that cannot be erased or programmed. See Table 4-13. 5:0 FPS Flash Protect Select Bits -- This 6-bit field determines the protected Flash locations that cannot be erased or programmed. SeeTable 4-14. Table 4-13. EEPROM Block Protection EPS Address Area Protected Memory Size Protected (bytes) Number of Sectors Protected 0x3 N/A 0 0 0x2 0x17F0 - 0x17FF 32 4 0x1 0x17E0 - 0x17FF 64 8 0x0 0x17C0-0x17FF 128 16 Table 4-14. Flash Block Protection FPS Address Area Protected Memory Size Protected (bytes) Number of Sectors Protected 0x3F N/A 0 0 0x3E 0xFA00-0xFFFF 1.5K 2 0x3D 0xF400-0xFFFF 3K 4 0x3C 0xEE00-0xFFFF 4.5K 6 0x3B 0xE800-0xFFFF 6K 8 ... ... ... ... 0x37 0xD000-0xFFFF 12K 16 0x36 0xCA00-0xFFFF 13.5K 18 0x35 0xC400-0xFFFF 15K 20 0x34 0xBE00-0xFFFF 16.5K 22 ... ... ... ... 0x2C 0x8E00-0xFFFF 28.5K 38 0x2B 0x8800-0xFFFF 30K 40 0x2A 0x8200-0xFFFF 31.5K 42 0x29 0x7C00-0xFFFF 33K 44 ... ... ... ... 0x22 0x5200-0xFFFF 43.5K 58 0x21 0x4C00-0xFFFF 45K 60 0x20 0x4600-0xFFFF 46.5K 62 0x1F 0x4000-0xFFFF 48K 64 ... ... ... ... MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 65 Chapter 4 Memory Table 4-14. Flash Block Protection (continued) FPS Address Area Protected Memory Size Protected (bytes) Number of Sectors Protected 0x1B 0x2800-0xFFFF 54K 72 0x1A 0x2200-0xFFFF 55.5K 74 0x19 0x1C00-0xFFFF 57K 76 0x18-0x00 0x0000-0xFFFF 64K 86 4.5.11.5 Flash and EEPROM Status Register (FSTAT) 7 R 6 5 4 FPVIOL FACCERR 0 0 FCCF FCBEF 3 2 1 0 0 FBLANK 0 0 0 0 0 0 W Reset 1 1 = Unimplemented or Reserved Figure 4-9. Flash and EEPROM Status Register (FSTAT) Table 4-15. FSTAT Register Field Descriptions Field Description 7 FCBEF Command Buffer Empty Flag -- The FCBEF bit is used to launch commands. It also indicates that the command buffer is empty so that a new command sequence can be executed when performing burst programming. The FCBEF bit is cleared by writing a 1 to it or when a burst program command is transferred to the array for programming. Only burst program commands can be buffered. 0 Command buffer is full (not ready for additional commands). 1 A new burst program command can be written to the command buffer. 6 FCCF Command Complete Flag -- FCCF is set automatically when the command buffer is empty and no command is being processed. FCCF is cleared automatically when a new command is started (by writing 1 to FCBEF to register a command). Writing to FCCF has no meaning or effect. 0 Command in progress 1 All commands complete 5 FPVIOL Protection Violation Flag -- FPVIOL is set automatically when a command that attempts to erase or program a location in a protected block is launched (the erroneous command is ignored). FPVIOL is cleared by writing a 1 to FPVIOL. 0 No protection violation. 1 An attempt was made to erase or program a protected location. MC9S08DZ60 Series Data Sheet, Rev. 4 66 Freescale Semiconductor Chapter 4 Memory Table 4-15. FSTAT Register Field Descriptions (continued) Field Description 4 FACCERR Access Error Flag -- FACCERR is set automatically when the proper command sequence is not obeyed exactly (the erroneous command is ignored), if a program or erase operation is attempted before the FCDIV register has been initialized, or if the MCU enters stop while a command was in progress. For a more detailed discussion of the exact actions that are considered access errors, see Section 4.5.6, "Access Errors." FACCERR is cleared by writing a 1 to FACCERR. Writing a 0 to FACCERR has no meaning or effect. 0 No access error. 1 An access error has occurred. 2 FBLANK Verified as All Blank (erased) Flag -- FBLANK is set automatically at the conclusion of a blank check command if the entire Flash or EEPROM array was verified to be erased. FBLANK is cleared by clearing FCBEF to write a new valid command. Writing to FBLANK has no meaning or effect. 0 After a blank check command is completed and FCCF = 1, FBLANK = 0 indicates the Flash or EEPROM array is not completely erased. 1 After a blank check command is completed and FCCF = 1, FBLANK = 1 indicates the Flash or EEPROM array is completely erased (all 0xFFFF). 4.5.11.6 Flash and EEPROM Command Register (FCMD) Only six command codes are recognized in normal user modes, as shown in Table 4-16. All other command codes are illegal and generate an access error. Refer to Section 4.5.3, "Program and Erase Command Execution," for a detailed discussion of Flash and EEPROM programming and erase operations. R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset FCMD 0 0 0 0 Figure 4-10. Flash and EEPROM Command Register (FCMD) Table 4-16. Flash and EEPROM Commands Command FCMD Equate File Label Blank check 0x05 mBlank Byte program 0x20 mByteProg Burst program 0x25 mBurstProg Sector erase 0x40 mSectorErase Mass erase 0x41 mMassErase Sector erase abort 0x47 mEraseAbort It is not necessary to perform a blank check command after a mass erase operation. Only blank check is required as part of the security unlocking mechanism. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 67 Chapter 4 Memory MC9S08DZ60 Series Data Sheet, Rev. 4 68 Freescale Semiconductor Chapter 5 Resets, Interrupts, and General System Control 5.1 Introduction This section discusses basic reset and interrupt mechanisms and their various sources in the MC9S08DZ60 Series. Some interrupt sources from peripheral modules are discussed in greater detail within other sections of this data sheet. This section gathers basic information about all reset and interrupt sources in one place for easy reference. A few reset and interrupt sources, including the computer operating properly (COP) watchdog, are not part of on-chip peripheral systems with their own chapters. 5.2 Features Reset and interrupt features include: * Multiple sources of reset for flexible system configuration and reliable operation * Reset status register (SRS) to indicate source of most recent reset * Separate interrupt vector for each module (reduces polling overhead); see Table 5-1 5.3 MCU Reset Resetting the MCU provides a way to start processing from a known set of initial conditions. During reset, most control and status registers are forced to initial values and the program counter is loaded from the reset vector (0xFFFE:0xFFFF). On-chip peripheral modules are disabled and I/O pins are initially configured as general-purpose high-impedance inputs with pull-up devices disabled. The I bit in the condition code register (CCR) is set to block maskable interrupts so the user program has a chance to initialize the stack pointer (SP) and system control settings. (See the CPU chapter for information on the Interrupt (I) bit.) SP is forced to 0x00FF at reset. The MC9S08DZ60 Series has eight sources for reset: * Power-on reset (POR) * External pin reset (PIN) * Computer operating properly (COP) timer * Illegal opcode detect (ILOP) * Illegal address detect (ILAD) * Low-voltage detect (LVD) * Loss of clock (LOC) * Background debug forced reset (BDFR) Each of these sources, with the exception of the background debug forced reset, has an associated bit in the system reset status register (SRS). MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 69 Chapter 5 Resets, Interrupts, and General System Control 5.4 Computer Operating Properly (COP) Watchdog The COP watchdog is intended to force a system reset when the application software fails to execute as expected. To prevent a system reset from the COP timer (when it is enabled), application software must reset the COP counter periodically. If the application program gets lost and fails to reset the COP counter before it times out, a system reset is generated to force the system back to a known starting point. After any reset, the COP watchdog is enabled (see Section 5.8.4, "System Options Register 1 (SOPT1)," for additional information). If the COP watchdog is not used in an application, it can be disabled by clearing COPT bits in SOPT1. The COP counter is reset by writing 0x55 and 0xAA (in this order) to the address of SRS during the selected timeout period. Writes do not affect the data in the read-only SRS. As soon as the write sequence is done, the COP timeout period is restarted. If the program fails to do this during the time-out period, the MCU will reset. Also, if any value other than 0x55 or 0xAA is written to SRS, the MCU is immediately reset. The COPCLKS bit in SOPT2 (see Section 5.8.5, "System Options Register 2 (SOPT2)," for additional information) selects the clock source used for the COP timer. The clock source options are either the bus clock or an internal 1-kHz clock source. With each clock source, there are three associated time-outs controlled by the COPT bits in SOPT1. Table 5-6 summaries the control functions of the COPCLKS and COPT bits. The COP watchdog defaults to operation from the 1-kHz clock source and the longest time-out (210 cycles). When the bus clock source is selected, windowed COP operation is available by setting COPW in the SOPT2 register. In this mode, writes to the SRS register to clear the COP timer must occur in the last 25% of the selected timeout period. A premature write immediately resets the MCU. When the 1-kHz clock source is selected, windowed COP operation is not available. The COP counter is initialized by the first writes to the SOPT1 and SOPT2 registers and after any system reset. Subsequent writes to SOPT1 and SOPT2 have no effect on COP operation. Even if the application will use the reset default settings of COPT, COPCLKS, and COPW bits, the user should write to the write-once SOPT1 and SOPT2 registers during reset initialization to lock in the settings. This will prevent accidental changes if the application program gets lost. The write to SRS that services (clears) the COP counter should not be placed in an interrupt service routine (ISR) because the ISR could continue to be executed periodically even if the main application program fails. If the bus clock source is selected, the COP counter does not increment while the MCU is in background debug mode or while the system is in stop mode. The COP counter resumes when the MCU exits background debug mode or stop mode. If the 1-kHz clock source is selected, the COP counter is re-initialized to zero upon entry to either background debug mode or stop mode and begins from zero upon exit from background debug mode or stop mode. MC9S08DZ60 Series Data Sheet, Rev. 4 70 Freescale Semiconductor Chapter 5 Resets, Interrupts, and General System Control 5.5 Interrupts Interrupts provide a way to save the current CPU status and registers, execute an interrupt service routine (ISR), and then restore the CPU status so processing resumes where it left off before the interrupt. Other than the software interrupt (SWI), which is a program instruction, interrupts are caused by hardware events such as an edge on the IRQ pin or a timer-overflow event. The debug module can also generate an SWI under certain circumstances. If an event occurs in an enabled interrupt source, an associated read-only status flag will become set. The CPU will not respond unless the local interrupt enable is a 1 to enable the interrupt and the I bit in the CCR is 0 to allow interrupts. The global interrupt mask (I bit) in the CCR is initially set after reset which prevents all maskable interrupt sources. The user program initializes the stack pointer and performs other system setup before clearing the I bit to allow the CPU to respond to interrupts. When the CPU receives a qualified interrupt request, it completes the current instruction before responding to the interrupt. The interrupt sequence obeys the same cycle-by-cycle sequence as the SWI instruction and consists of: * * * * Saving the CPU registers on the stack Setting the I bit in the CCR to mask further interrupts Fetching the interrupt vector for the highest-priority interrupt that is currently pending Filling the instruction queue with the first three bytes of program information starting from the address fetched from the interrupt vector locations While the CPU is responding to the interrupt, the I bit is automatically set to avoid the possibility of another interrupt interrupting the ISR itself (this is called nesting of interrupts). Normally, the I bit is restored to 0 when the CCR is restored from the value stacked on entry to the ISR. In rare cases, the I bit can be cleared inside an ISR (after clearing the status flag that generated the interrupt) so that other interrupts can be serviced without waiting for the first service routine to finish. This practice is not recommended for anyone other than the most experienced programmers because it can lead to subtle program errors that are difficult to debug. The interrupt service routine ends with a return-from-interrupt (RTI) instruction which restores the CCR, A, X, and PC registers to their pre-interrupt values by reading the previously saved information from the stack. NOTE For compatibility with M68HC08 devices, the H register is not automatically saved and restored. It is good programming practice to push H onto the stack at the start of the interrupt service routine (ISR) and restore it immediately before the RTI that is used to return from the ISR. If more than one interrupt is pending when the I bit is cleared, the highest priority source is serviced first (see Table 5-1). MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 71 Chapter 5 Resets, Interrupts, and General System Control 5.5.1 Interrupt Stack Frame Figure 5-1 shows the contents and organization of a stack frame. Before the interrupt, the stack pointer (SP) points at the next available byte location on the stack. The current values of CPU registers are stored on the stack starting with the low-order byte of the program counter (PCL) and ending with the CCR. After stacking, the SP points at the next available location on the stack which is the address that is one less than the address where the CCR was saved. The PC value that is stacked is the address of the instruction in the main program that would have executed next if the interrupt had not occurred. UNSTACKING ORDER TOWARD LOWER ADDRESSES 7 0 SP AFTER INTERRUPT STACKING 5 1 4 2 ACCUMULATOR 3 3 INDEX REGISTER (LOW BYTE X)* 2 4 PROGRAM COUNTER HIGH 1 5 PROGRAM COUNTER LOW CONDITION CODE REGISTER STACKING ORDER SP BEFORE THE INTERRUPT TOWARD HIGHER ADDRESSES * High byte (H) of index register is not automatically stacked. Figure 5-1. Interrupt Stack Frame When an RTI instruction is executed, these values are recovered from the stack in reverse order. As part of the RTI sequence, the CPU fills the instruction pipeline by reading three bytes of program information, starting from the PC address recovered from the stack. The status flag corresponding to the interrupt source must be acknowledged (cleared) before returning from the ISR. Typically, the flag is cleared at the beginning of the ISR so that if another interrupt is generated by this same source, it will be registered so it can be serviced after completion of the current ISR. 5.5.2 External Interrupt Request (IRQ) Pin External interrupts are managed by the IRQ status and control register, IRQSC. When the IRQ function is enabled, synchronous logic monitors the pin for edge-only or edge-and-level events. When the MCU is in stop mode and system clocks are shut down, a separate asynchronous path is used so the IRQ (if enabled) can wake the MCU. 5.5.2.1 Pin Configuration Options The IRQ pin enable (IRQPE) control bit in IRQSC must be 1 in order for the IRQ pin to act as the interrupt request (IRQ) input. As an IRQ input, the user can choose the polarity of edges or levels detected (IRQEDG), whether the pin detects edges-only or edges and levels (IRQMOD), and whether an event causes an interrupt or only sets the IRQF flag which can be polled by software. MC9S08DZ60 Series Data Sheet, Rev. 4 72 Freescale Semiconductor Chapter 5 Resets, Interrupts, and General System Control The IRQ pin, when enabled, defaults to use an internal pull device (IRQPDD = 0), the device is a pull-up or pull-down depending on the polarity chosen. If the user desires to use an external pull-up or pull-down, the IRQPDD can be written to a 1 to turn off the internal device. BIH and BIL instructions may be used to detect the level on the IRQ pin when the pin is configured to act as the IRQ input. 5.5.2.2 Edge and Level Sensitivity The IRQMOD control bit reconfigures the detection logic so it detects edge events and pin levels. In the edge and level detection mode, the IRQF status flag becomes set when an edge is detected (when the IRQ pin changes from the deasserted to the asserted level), but the flag is continuously set (and cannot be cleared) as long as the IRQ pin remains at the asserted level. 5.5.3 Interrupt Vectors, Sources, and Local Masks Table 5-1 provides a summary of all interrupt sources. Higher-priority sources are located toward the bottom of the table. The high-order byte of the address for the interrupt service routine is located at the first address in the vector address column, and the low-order byte of the address for the interrupt service routine is located at the next higher address. When an interrupt condition occurs, an associated flag bit becomes set. If the associated local interrupt enable is 1, an interrupt request is sent to the CPU. Within the CPU, if the global interrupt mask (I bit in the CCR) is 0, the CPU will finish the current instruction; stack the PCL, PCH, X, A, and CCR CPU registers; set the I bit; and then fetch the interrupt vector for the highest priority pending interrupt. Processing then continues in the interrupt service routine. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 73 Chapter 5 Resets, Interrupts, and General System Control Table 5-1. Vector Summary1 1 Vector No. Address (High/Low) Vector Name Module 31 30 29 28 27 26 25 24 23 22 0xFFC0/0xFFC1 0xFFC2/0xFFC3 0xFFC4/0xFFC5 0xFFC6/0xFFC7 0xFFC8/0xFFC9 0xFFCA/0xFFCB 0xFFCC/0xFFCD 0xFFCE/0xFFCF 0xFFD0/0xFFD1 0xFFD2/0xFFD3 Vacmp2 Vacmp1 Vcantx Vcanrx Vcanerr Vcanwu Vrtc Viic Vadc Vport ACMP2 ACMP1 MSCAN MSCAN MSCAN MSCAN RTC IIC ADC Port A,B,D 21 20 0xFFD4/0xFFD5 0xFFD6/0xFFD7 Vsci2tx Vsci2rx SCI2 SCI2 19 0xFFD8/0xFFD9 Vsci2err SCI2 18 17 0xFFDA/0xFFDB 0xFFDC/0xFFDD Vsci1tx Vsci1rx SCI1 SCI1 16 0xFFDE/0xFFDF Vsci1err SCI1 15 0xFFE0/0xFFE1 Vspi SPI 14 13 12 11 10 9 8 7 6 5 4 3 0xFFE2/0xFFE3 0xFFE4/0xFFE5 0xFFE6/0xFFE7 0xFFE8/0xFFE9 0xFFEA/0xFFEB 0xFFEC/0xFFED 0xFFEE/0xFFEF 0xFFF0/0xFFF1 0xFFF2/0xFFF3 0xFFF4/0xFFF5 0xFFF6/0xFFF7 0xFFF8/0xFFF9 Vtpm2ovf Vtpm2ch1 Vtpm2ch0 Vtpm1ovf Vtpm1ch5 Vtpm1ch4 Vtpm1ch3 Vtpm1ch2 Vtpm1ch1 Vtpm1ch0 Vlol Vlvd 2 1 0 0xFFFA/0xFFFB 0xFFFC/0xFFFD 0xFFFE/0xFFFF Virq Vswi Vreset TPM2 TPM2 TPM2 TPM1 TPM1 TPM1 TPM1 TPM1 TPM1 TPM1 MCG System control IRQ Core System control Source Enable Description ACF ACIE ACF ACIE TXE[2:0] TXEIE[2:0] RXF RXFIE CSCIF, OVRIF CSCIE, OVRIE WUPIF WUPIE RTIF RTIE IICIS IICIE COCO AIEN PTAIF, PTBIF, PTAIE, PTBIE, PTDIE PTDIF TDRE, TC TIE, TCIE IDLE, LBKDIF, ILIE, LBKDIE, RIE, RDRF, RXEDGIF RXEDGIE OR, NF ORIE, NFIE, FE, PF FEIE, PFIE TDRE, TC TIE, TCIE IDLE, LBKDIF, ILIE, LBKDIE, RIE, RDRF, RXEDGIF RXEDGIE OR, NF, ORIE, NFIE, FE, PF FEIE, PFIE SPIF, MODF, SPIE, SPIE, SPTIE SPTEF TOF TOIE CH1F CH1IE CH0F CH0IE TOF TOIE CH5F CH5IE CH4F CH4IE CH3F CH3IE CH2F CH2IE CH1F CH1IE CH0F CH0IE LOLS LOLIE LVWF LVWIE IRQF SWI Instruction COP, LOC, LVD, RESET, ILOP, ILAD, POR, BDFR IRQIE -- COPE CME LVDRE -- -- -- -- -- Analog comparator 2 Analog comparator 1 CAN transmit CAN receive CAN errors CAN wake-up Real-time interrupt IIC control ADC Port Pins SCI2 transmit SCI2 receive SCI2 error SCI1 transmit SCI1 receive SCI1 error SPI TPM2 overflow TPM2 channel 1 TPM2 channel 0 TPM1 overflow TPM1 channel 5 TPM1 channel 4 TPM1 channel 3 TPM1 channel 2 TPM1 channel 1 TPM1 channel 0 MCG loss of lock Low-voltage warning IRQ pin Software interrupt Watchdog timer Loss-of-clock Low-voltage detect External pin Illegal opcode Illegal address Power-on-reset BDM-forced reset Vector priority is shown from lowest (first row) to highest (last row). For example, Vreset is the highest priority vector. MC9S08DZ60 Series Data Sheet, Rev. 4 74 Freescale Semiconductor Chapter 5 Resets, Interrupts, and General System Control 5.6 Low-Voltage Detect (LVD) System The MC9S08DZ60 Series includes a system to protect against low-voltage conditions in order to protect memory contents and control MCU system states during supply voltage variations. The system is comprised of a power-on reset (POR) circuit and a LVD circuit with trip voltages for warning and detection. The LVD circuit is enabled when LVDE in SPMSC1 is set to 1. The LVD is disabled upon entering any of the stop modes unless LVDSE is set in SPMSC1. If LVDSE and LVDE are both set, then the MCU cannot enter stop2 (it will enter stop3 instead), and the current consumption in stop3 with the LVD enabled will be higher. 5.6.1 Power-On Reset Operation When power is initially applied to the MCU, or when the supply voltage drops below the power-on reset rearm voltage level, VPOR, the POR circuit will cause a reset condition. As the supply voltage rises, the LVD circuit will hold the MCU in reset until the supply has risen above the low-voltage detection low threshold, VLVDL. Both the POR bit and the LVD bit in SRS are set following a POR. 5.6.2 Low-Voltage Detection (LVD) Reset Operation The LVD can be configured to generate a reset upon detection of a low-voltage condition by setting LVDRE to 1. The low-voltage detection threshold is determined by the LVDV bit. After an LVD reset has occurred, the LVD system will hold the MCU in reset until the supply voltage has risen above the low-voltage detection threshold. The LVD bit in the SRS register is set following either an LVD reset or POR. 5.6.3 Low-Voltage Warning (LVW) Interrupt Operation The LVD system has a low-voltage warning flag to indicate to the user that the supply voltage is approaching the low-voltage condition. When a low-voltage warning condition is detected and is configured for interrupt operation (LVWIE set to 1), LVWF in SPMSC1 will be set and an LVW interrupt request will occur. 5.7 MCLK Output The PTA0 pin is shared with the MCLK clock output. If the MCSEL bits are all zeroes, the MCLK clock is disabled. Setting any of the MCSEL bits causes the PTA0 pin to output a divided version of the internal MCU bus clock regardless of the state of the port data direction control bit for the pin. The divide ratio is determined by the MCSEL bits. The slew rate and drive strength for the pin are controlled by PTASE0 and PTADS0, respectively. The maximum clock output frequency is limited if slew rate control is enabled, see the electrical specifications for the maximum frequency under different conditions. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 75 Chapter 5 Resets, Interrupts, and General System Control 5.8 Reset, Interrupt, and System Control Registers and Control Bits One 8-bit register in the direct page register space and eight 8-bit registers in the high-page register space are related to reset and interrupt systems. Refer to Table 4-2 and Table 4-3 in Chapter 4, "Memory," of this data sheet for the absolute address assignments for all registers. This section refers to registers and control bits only by their names. A Freescale-provided equate or header file is used to translate these names into the appropriate absolute addresses. Some control bits in the SOPT1 and SPMSC2 registers are related to modes of operation. Although brief descriptions of these bits are provided here, the related functions are discussed in greater detail in Chapter 3, "Modes of Operation." MC9S08DZ60 Series Data Sheet, Rev. 4 76 Freescale Semiconductor Chapter 5 Resets, Interrupts, and General System Control 5.8.1 Interrupt Pin Request Status and Control Register (IRQSC) This direct page register includes status and control bits which are used to configure the IRQ function, report status, and acknowledge IRQ events. 7 R 6 5 4 IRQPDD IRQEDG IRQPE 0 3 2 IRQF 0 W Reset 1 0 IRQIE IRQMOD 0 0 IRQACK 0 0 0 0 0 0 = Unimplemented or Reserved Figure 5-2. Interrupt Request Status and Control Register (IRQSC) Table 5-2. IRQSC Register Field Descriptions Field Description 6 IRQPDD Interrupt Request (IRQ) Pull Device Disable-- This read/write control bit is used to disable the internal pull-up/pull-down device when the IRQ pin is enabled (IRQPE = 1) allowing for an external device to be used. 0 IRQ pull device enabled if IRQPE = 1. 1 IRQ pull device disabled if IRQPE = 1. 5 IRQEDG Interrupt Request (IRQ) Edge Select -- This read/write control bit is used to select the polarity of edges or levels on the IRQ pin that cause IRQF to be set. The IRQMOD control bit determines whether the IRQ pin is sensitive to both edges and levels or only edges. When the IRQ pin is enabled as the IRQ input and is configured to detect rising edges, it has a pull-down. When the IRQ pin is enabled as the IRQ input and is configured to detect falling edges, it has a pull-up. 0 IRQ is falling edge or falling edge/low-level sensitive. 1 IRQ is rising edge or rising edge/high-level sensitive. 4 IRQPE IRQ Pin Enable -- This read/write control bit enables the IRQ pin function. When this bit is set the IRQ pin can be used as an interrupt request. 0 IRQ pin function is disabled. 1 IRQ pin function is enabled. 3 IRQF 2 IRQACK 1 IRQIE 0 IRQMOD IRQ Flag -- This read-only status bit indicates when an interrupt request event has occurred. 0 No IRQ request. 1 IRQ event detected. IRQ Acknowledge -- This write-only bit is used to acknowledge interrupt request events (write 1 to clear IRQF). Writing 0 has no meaning or effect. Reads always return 0. If edge-and-level detection is selected (IRQMOD = 1), IRQF cannot be cleared while the IRQ pin remains at its asserted level. IRQ Interrupt Enable -- This read/write control bit determines whether IRQ events generate an interrupt request. 0 Interrupt request when IRQF set is disabled (use polling). 1 Interrupt requested whenever IRQF = 1. IRQ Detection Mode -- This read/write control bit selects either edge-only detection or edge-and-level detection. The IRQEDG control bit determines the polarity of edges and levels that are detected as interrupt request events. See Section 5.5.2.2, "Edge and Level Sensitivity" for more details. 0 IRQ event on falling edges or rising edges only. 1 IRQ event on falling edges and low levels or on rising edges and high levels. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 77 Chapter 5 Resets, Interrupts, and General System Control 5.8.2 System Reset Status Register (SRS) This high page register includes read-only status flags to indicate the source of the most recent reset. When a debug host forces reset by writing 1 to BDFR in the SBDFR register, none of the status bits in SRS will be set. Writing any value to this register address causes a COP reset when the COP is enabled except the values 0x55 and 0xAA. Writing a 0x55-0xAA sequence to this address clears the COP watchdog timer without affecting the contents of this register. The reset state of these bits depends on what caused the MCU to reset. R 7 6 5 4 3 2 1 0 POR PIN COP ILOP ILAD LOC LVD 0 W Writing 0x55, 0xAA to SRS address clears COP watchdog timer. POR: 1 0 0 0 0 0 1 0 LVD: u 0 0 0 0 0 1 0 Any other reset: 0 Note(1) Note(1) Note(1) Note(1) 0 0 0 1 Any of these reset sources that are active at the time of reset entry will cause the corresponding bit(s) to be set; bits corresponding to sources that are not active at the time of reset entry will be cleared. Figure 5-3. System Reset Status (SRS) Table 5-3. SRS Register Field Descriptions Field Description 7 POR Power-On Reset -- Reset was caused by the power-on detection logic. Because the internal supply voltage was ramping up at the time, the low-voltage reset (LVD) status bit is also set to indicate that the reset occurred while the internal supply was below the LVD threshold. 0 Reset not caused by POR. 1 POR caused reset. 6 PIN External Reset Pin -- Reset was caused by an active-low level on the external reset pin. 0 Reset not caused by external reset pin. 1 Reset came from external reset pin. 5 COP Computer Operating Properly (COP) Watchdog -- Reset was caused by the COP watchdog timer timing out. This reset source can be blocked by COPE = 0. 0 Reset not caused by COP timeout. 1 Reset caused by COP timeout. 4 ILOP Illegal Opcode -- Reset was caused by an attempt to execute an unimplemented or illegal opcode. The STOP instruction is considered illegal if stop is disabled by STOPE = 0 in the SOPT register. The BGND instruction is considered illegal if active background mode is disabled by ENBDM = 0 in the BDCSC register. 0 Reset not caused by an illegal opcode. 1 Reset caused by an illegal opcode. 3 ILAD Illegal Address -- Reset was caused by an attempt to access either data or an instruction at an unimplemented memory address. 0 Reset not caused by an illegal address. 1 Reset caused by an illegal address. MC9S08DZ60 Series Data Sheet, Rev. 4 78 Freescale Semiconductor Chapter 5 Resets, Interrupts, and General System Control Table 5-3. SRS Register Field Descriptions Field Description 2 LOC Loss of Clock -- Reset was caused by a loss of external clock. 0 Reset not caused by loss of external clock 1 Reset caused by loss of external clock 1 LVD Low-Voltage Detect -- If the LVDRE bit is set and the supply drops below the LVD trip voltage, an LVD reset will occur. This bit is also set by POR. 0 Reset not caused by LVD trip or POR. 1 Reset caused by LVD trip or POR. 5.8.3 System Background Debug Force Reset Register (SBDFR) This high page register contains a single write-only control bit. A serial background command such as WRITE_BYTE must be used to write to SBDFR. Attempts to write this register from a user program are ignored. Reads always return 0x00. R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 BDFR1 W Reset: 0 0 0 0 0 0 0 0 = Unimplemented or Reserved 1 BDFR is writable only through serial background debug commands, not from user programs. Figure 5-4. System Background Debug Force Reset Register (SBDFR) Table 5-4. SBDFR Register Field Descriptions Field Description 0 BDFR Background Debug Force Reset -- A serial background command such as WRITE_BYTE can be used to allow an external debug host to force a target system reset. Writing 1 to this bit forces an MCU reset. This bit cannot be written from a user program. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 79 Chapter 5 Resets, Interrupts, and General System Control 5.8.4 System Options Register 1 (SOPT1) This high page register is a write-once register so only the first write after reset is honored. It can be read at any time. Any subsequent attempt to write to SOPT1 (intentionally or unintentionally) is ignored to avoid accidental changes to these sensitive settings. This register should be written during the user's reset initialization program to set the desired controls even if the desired settings are the same as the reset settings. 7 6 5 4 3 STOPE SCI2PS IICPS 0 0 0 R COPT 2 1 0 0 0 0 0 0 0 W Reset: 1 1 = Unimplemented or Reserved Figure 5-5. System Options Register 1 (SOPT1) Table 5-5. SOPT1 Register Field Descriptions Field Description 7:6 COPT[1:0] COP Watchdog Timeout -- These write-once bits select the timeout period of the COP. COPT along with COPCLKS in SOPT2 defines the COP timeout period. See Table 5-6. 5 STOPE Stop Mode Enable -- This write-once bit is used to enable stop mode. If stop mode is disabled and a user program attempts to execute a STOP instruction, an illegal opcode reset is forced. 0 Stop mode disabled. 1 Stop mode enabled. 4 SCI2PS SCI2 Pin Select-- This write-once bit selects the location of the RxD2 and TxD2 pins of the SCI2 module. 0 TxD2 on PTF0, RxD2 on PTF1. 1 TxD2 on PTE6, RxD2 on PTE7. 3 IICPS IIC Pin Select-- This write-once bit selects the location of the SCL and SDA pins of the IIC module. 0 SCL on PTF2, SDA on PTF3. 1 SCL on PTE4, SDA on PTE5. Table 5-6. COP Configuration Options Control Bits Clock Source COP Window1 Opens (COPW = 1) N/A N/A COP Overflow Count COPCLKS COPT[1:0] N/A 0:0 0 0:1 1 kHz N/A 25 0 1:0 1 kHz N/A 28 cycles (256 ms1) 0 1:1 1 kHz N/A 210 cycles (1.024 s1) 1 0:1 Bus 6144 cycles 213 cycles 1 1:0 Bus 49,152 cycles 216 cycles 1 1:1 Bus 196,608 cycles 218 cycles COP is disabled cycles (32 ms2) 1 Windowed COP operation requires the user to clear the COP timer in the last 25% of the selected timeout period. This column displays the minimum number of clock counts required before the COP timer can be reset when in windowed COP mode (COPW = 1). 2 Values shown in milliseconds based on t LPO = 1 ms. See tLPO in the appendix Section A.12.1, "Control Timing," for the tolerance of this value. MC9S08DZ60 Series Data Sheet, Rev. 4 80 Freescale Semiconductor Chapter 5 Resets, Interrupts, and General System Control 5.8.5 System Options Register 2 (SOPT2) This high page register contains bits to configure MCU specific features on the MC9S08DZ60 Series devices. R 7 6 5 COPCLKS1 COPW1 0 0 4 3 0 2 1 0 0 ADHTS MCSEL W Reset: 0 0 0 0 0 0 = Unimplemented or Reserved Figure 5-6. System Options Register 2 (SOPT2) 1 This bit can be written only one time after reset. Additional writes are ignored. Table 5-7. SOPT2 Register Field Descriptions Field 7 COPCLKS Description COP Watchdog Clock Select -- This write-once bit selects the clock source of the COP watchdog. See Table 5-6 for details. 0 Internal 1-kHz clock is source to COP. 1 Bus clock is source to COP. 6 COPW COP Window -- This write-once bit selects the COP operation mode. When set, the 0x55-0xAA write sequence to the SRS register must occur in the last 25% of the selected period. Any write to the SRS register during the first 75% of the selected period will reset the MCU. 0 Normal COP operation. 1 Window COP operation. 4 ADHTS ADC Hardware Trigger Select -- This bit selects which hardware trigger initiates conversion for the analog to digital converter when the ADC hardware trigger is enabled (ADCTRG is set in ADCSC2 register). 0 Real Time Counter (RTC) overflow. 1 External Interrupt Request (IRQ) pin. 2:0 MCSEL MCLK Divide Select-- These bits enable the MCLK output on PTA0 pin and select the divide ratio for the MCLK output according to the formula below when the MCSEL bits are not equal to all zeroes. In case that the MCSEL bits are all zeroes, the MCLK output is disabled. MCLK frequency = Bus Clock frequency / (2 * MCSEL) MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 81 Chapter 5 Resets, Interrupts, and General System Control 5.8.6 System Device Identification Register (SDIDH, SDIDL) These high page read-only registers are included so host development systems can identify the HCS08 derivative and revision number. This allows the development software to recognize where specific memory blocks, registers, and control bits are located in a target MCU. 7 6 R 5 4 Reserved 3 2 1 0 ID11 ID10 ID9 ID8 0 0 0 0 W Reset: 01 01 01 01 = Unimplemented or Reserved 1 The revision number that is hard coded into these bits reflects the current silicon revision level. Figure 5-7. System Device Identification Register -- High (SDIDH) Table 5-8. SDIDH Register Field Descriptions Field Description 3:0 ID[11:8] Part Identification Number -- MC9S08DZ60 Series MCUs are hard-coded to the value 0x00E. See also ID bits in Table 5-9. R 7 6 5 4 3 2 1 0 ID7 ID6 ID5 ID4 ID3 ID2 ID1 ID0 0 0 0 0 1 1 1 0 W Reset: = Unimplemented or Reserved Figure 5-8. System Device Identification Register -- Low (SDIDL) Table 5-9. SDIDL Register Field Descriptions Field Description 7:0 ID[7:0] Part Identification Number -- MC9S08DZ60 Series MCUs are hard-coded to the value 0x00E. See also ID bits in Table 5-8. MC9S08DZ60 Series Data Sheet, Rev. 4 82 Freescale Semiconductor Chapter 5 Resets, Interrupts, and General System Control 5.8.7 System Power Management Status and Control 1 Register (SPMSC1) This high page register contains status and control bits to support the low-voltage detect function, and to enable the bandgap voltage reference for use by the ADC and ACMP modules. This register should be written during the user's reset initialization program to set the desired controls even if the desired settings are the same as the reset settings. 7 R LVWF 6 1 4 3 2 LVWIE LVDRE2 LVDSE LVDE2 0 1 1 1 0 W Reset: 5 1 0 0 BGBE LVWACK 0 0 0 0 = Unimplemented or Reserved 1 2 LVWF will be set in the case when VSupply transitions below the trip point or after reset and VSupply is already below VLVW. This bit can be written only one time after reset. Additional writes are ignored. Figure 5-9. System Power Management Status and Control 1 Register (SPMSC1) Table 5-10. SPMSC1 Register Field Descriptions Field 7 LVWF 6 LVWACK Description Low-Voltage Warning Flag -- The LVWF bit indicates the low-voltage warning status. 0 low-voltage warning is not present. 1 low-voltage warning is present or was present. Low-Voltage Warning Acknowledge -- If LVWF = 1, a low-voltage condition has occurred. To acknowledge this low-voltage warning, write 1 to LVWACK, which will automatically clear LVWF to 0 if the low-voltage warning is no longer present. 5 LVWIE Low-Voltage Warning Interrupt Enable -- This bit enables hardware interrupt requests for LVWF. 0 Hardware interrupt disabled (use polling). 1 Request a hardware interrupt when LVWF = 1. 4 LVDRE Low-Voltage Detect Reset Enable -- This write-once bit enables LVD events to generate a hardware reset (provided LVDE = 1). 0 LVD events do not generate hardware resets. 1 Force an MCU reset when an enabled low-voltage detect event occurs. 3 LVDSE Low-Voltage Detect Stop Enable -- Provided LVDE = 1, this read/write bit determines whether the low-voltage detect function operates when the MCU is in stop mode. 0 Low-voltage detect disabled during stop mode. 1 Low-voltage detect enabled during stop mode. 2 LVDE Low-Voltage Detect Enable -- This write-once bit enables low-voltage detect logic and qualifies the operation of other bits in this register. 0 LVD logic disabled. 1 LVD logic enabled. 0 BGBE Bandgap Buffer Enable -- This bit enables an internal buffer for the bandgap voltage reference for use by the ADC and ACMP modules on one of its internal channels. 0 Bandgap buffer disabled. 1 Bandgap buffer enabled. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 83 Chapter 5 Resets, Interrupts, and General System Control 5.8.8 System Power Management Status and Control 2 Register (SPMSC2) This register is used to report the status of the low-voltage warning function, and to configure the stop mode behavior of the MCU. This register should be written during the user's reset initialization program to set the desired controls even if the desired settings are the same as the reset settings. R 7 6 0 0 5 4 LVDV1 LVWV 3 2 1 PPDF 0 0 W 0 PPDC2 PPDACK Power-on Reset: 0 0 0 0 0 0 0 0 LVD Reset: 0 0 u u 0 0 0 0 Any other Reset: 0 0 u u 0 0 0 0 = Unimplemented or Reserved 1 2 u = Unaffected by reset This bit can be written only one time after power-on reset. Additional writes are ignored. This bit can be written only one time after reset. Additional writes are ignored. Figure 5-10. System Power Management Status and Control 2 Register (SPMSC2) Table 5-11. SPMSC2 Register Field Descriptions Field Description 5 LVDV Low-Voltage Detect Voltage Select -- This write-once bit selects the low-voltage detect (LVD) trip point setting. It also selects the warning voltage range. See Table 5-12. 4 LVWV Low-Voltage Warning Voltage Select -- This bit selects the low-voltage warning (LVW) trip point voltage. See Table 5-12. 3 PPDF Partial Power Down Flag -- This read-only status bit indicates that the MCU has recovered from stop2 mode. 0 MCU has not recovered from stop2 mode. 1 MCU recovered from stop2 mode. 2 PPDACK 0 PPDC Partial Power Down Acknowledge -- Writing a 1 to PPDACK clears the PPDF bit. Partial Power Down Control -- This write-once bit controls whether stop2 or stop3 mode is selected. 0 Stop3 mode enabled. 1 Stop2, partial power down, mode enabled. Table 5-12. LVD and LVW Trip Point Typical Values1 1 LVDV:LVWV LVW Trip Point LVD Trip Point 0:0 VLVW0 = 2.74 V VLVD0 = 2.56 V 0:1 VLVW1 = 2.92 V 1:0 VLVW2 = 4.3 V 1:1 VLVW3 = 4.6 V VLVD1 = 4.0 V See Electrical Characteristics appendix for minimum and maximum values. MC9S08DZ60 Series Data Sheet, Rev. 4 84 Freescale Semiconductor Chapter 6 Parallel Input/Output Control This section explains software controls related to parallel input/output (I/O) and pin control. The MC9S08DZ60 Series has seven parallel I/O ports which include a total of up to 53 I/O pins and one input-only pin. See Chapter 2, "Pins and Connections," for more information about pin assignments and external hardware considerations of these pins. Many of these pins are shared with on-chip peripherals such as timer systems, communication systems, or pin interrupts as shown in Table 2-1. The peripheral modules have priority over the general-purpose I/O functions so that when a peripheral is enabled, the I/O functions associated with the shared pins are disabled. After reset, the shared peripheral functions are disabled and the pins are configured as inputs (PTxDDn = 0). The pin control functions for each pin are configured as follows: slew rate control enabled (PTxSEn = 1), low drive strength selected (PTxDSn = 0), and internal pull-ups disabled (PTxPEn = 0). * * 6.1 NOTE Not all general-purpose I/O pins are available on all packages. To avoid extra current drain from floating input pins, the user's reset initialization routine in the application program must either enable on-chip pull-up devices or change the direction of unconnected pins to outputs so the pins do not float. The PTE1 pin does not contain a clamp diode to VDD and should not be driven above VDD. The voltage measured on the internally pulled up PTE1 pin may be as low as VDD - 0.7 V. The internal gates connected to this pin are pulled all the way to VDD. Port Data and Data Direction Reading and writing of parallel I/Os are performed through the port data registers. The direction, either input or output, is controlled through the port data direction registers. The parallel I/O port function for an individual pin is illustrated in the block diagram shown in Figure 6-1. The data direction control bit (PTxDDn) determines whether the output buffer for the associated pin is enabled, and also controls the source for port data register reads. The input buffer for the associated pin is always enabled unless the pin is enabled as an analog function or is an output-only pin. When a shared digital function is enabled for a pin, the output buffer is controlled by the shared function. However, the data direction register bit will continue to control the source for reads of the port data register. When a shared analog function is enabled for a pin, both the input and output buffers are disabled. A value of 0 is read for any port data bit where the bit is an input (PTxDDn = 0) and the input buffer is disabled. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 85 Chapter 6 Parallel Input/Output Control In general, whenever a pin is shared with both an alternate digital function and an analog function, the analog function has priority such that if both the digital and analog functions are enabled, the analog function controls the pin. It is a good programming practice to write to the port data register before changing the direction of a port pin to become an output. This ensures that the pin will not be driven momentarily with an old data value that happened to be in the port data register. PTxDDn D Output Enable Q PTxDn D Output Data Q 1 Port Read Data 0 Input Data Synchronizer BUSCLK Figure 6-1. Parallel I/O Block Diagram 6.2 Pull-up, Slew Rate, and Drive Strength Associated with the parallel I/O ports is a set of registers located in the high page register space that operate independently of the parallel I/O registers. These registers are used to control pull-ups, slew rate, and drive strength for the pins. An internal pull-up device can be enabled for each port pin by setting the corresponding bit in the pull-up enable register (PTxPEn). The pull-up device is disabled if the pin is configured as an output by the parallel I/O control logic or any shared peripheral function regardless of the state of the corresponding pull-up enable register bit. The pull-up device is also disabled if the pin is controlled by an analog function. Slew rate control can be enabled for each port pin by setting the corresponding bit in the slew rate control register (PTxSEn). When enabled, slew control limits the rate at which an output can transition in order to reduce EMC emissions. Slew rate control has no effect on pins that are configured as inputs. NOTE Slew rate reset default values may differ between engineering samples and final production parts. Always initialize slew rate control to the desired value to ensure correct operation. MC9S08DZ60 Series Data Sheet, Rev. 4 86 Freescale Semiconductor Chapter 6 Parallel Input/Output Control An output pin can be selected to have high output drive strength by setting the corresponding bit in the drive strength select register (PTxDSn). When high drive is selected, a pin is capable of sourcing and sinking greater current. Even though every I/O pin can be selected as high drive, the user must ensure that the total current source and sink limits for the MCU are not exceeded. Drive strength selection is intended to affect the DC behavior of I/O pins. However, the AC behavior is also affected. High drive allows a pin to drive a greater load with the same switching speed as a low drive enabled pin into a smaller load. Because of this, the EMC emissions may be affected by enabling pins as high drive. 6.3 Pin Interrupts Port A, port B, and port D pins can be configured as external interrupt inputs and as an external means of waking the MCU from stop or wait low-power modes. The block diagram for each port interrupt logic is shown Figure 6-2. BUSCLK PTxACK VDD 1 PTxn 0 S RESET PTxIF D CLR Q PTxPS0 SYNCHRONIZER CK PTxES0 PORT INTERRUPT FF 1 PTxn 0 S STOP STOP BYPASS PTx INTERRUPT REQUEST PTxMOD PTxPSn PTxIE PTxESn Figure 6-2. Port Interrupt Block Diagram Writing to the PTxPSn bits in the port interrupt pin select register (PTxPS) independently enables or disables each port pin. Each port can be configured as edge sensitive or edge and level sensitive based on the PTxMOD bit in the port interrupt status and control register (PTxSC). Edge sensitivity can be software programmed to be either falling or rising; the level can be either low or high. The polarity of the edge or edge and level sensitivity is selected using the PTxESn bits in the port interrupt edge select register (PTxES). Synchronous logic is used to detect edges. Prior to detecting an edge, enabled port inputs must be at the deasserted logic level. A falling edge is detected when an enabled port input signal is seen as a logic 1 (the deasserted level) during one bus cycle and then a logic 0 (the asserted level) during the next cycle. A rising edge is detected when the input signal is seen as a logic 0 during one bus cycle and then a logic 1 during the next cycle. 6.3.1 Edge Only Sensitivity A valid edge on an enabled port pin will set PTxIF in PTxSC. If PTxIE in PTxSC is set, an interrupt request will be presented to the CPU. Clearing of PTxIF is accomplished by writing a 1 to PTxACK in PTxSC. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 87 Chapter 6 Parallel Input/Output Control 6.3.2 Edge and Level Sensitivity A valid edge or level on an enabled port pin will set PTxIF in PTxSC. If PTxIE in PTxSC is set, an interrupt request will be presented to the CPU. Clearing of PTxIF is accomplished by writing a 1 to PTxACK in PTxSC provided all enabled port inputs are at their deasserted levels. PTxIF will remain set if any enabled port pin is asserted while attempting to clear by writing a 1 to PTxACK. 6.3.3 Pull-up/Pull-down Resistors The port interrupt pins can be configured to use an internal pull-up/pull-down resistor using the associated I/O port pull-up enable register. If an internal resistor is enabled, the PTxES register is used to select whether the resistor is a pull-up (PTxESn = 0) or a pull-down (PTxESn = 1). 6.3.4 Pin Interrupt Initialization When an interrupt pin is first enabled, it is possible to get a false interrupt flag. To prevent a false interrupt request during pin interrupt initialization, the user should do the following: 1. Mask interrupts by clearing PTxIE in PTxSC. 2. Select the pin polarity by setting the appropriate PTxESn bits in PTxES. 3. If using internal pull-up/pull-down device, configure the associated pull enable bits in PTxPE. 4. Enable the interrupt pins by setting the appropriate PTxPSn bits in PTxPS. 5. Write to PTxACK in PTxSC to clear any false interrupts. 6. Set PTxIE in PTxSC to enable interrupts. 6.4 Pin Behavior in Stop Modes Pin behavior following execution of a STOP instruction depends on the stop mode that is entered. An explanation of pin behavior for the various stop modes follows: * Stop2 mode is a partial power-down mode, whereby I/O latches are maintained in their state as before the STOP instruction was executed. CPU register status and the state of I/O registers should be saved in RAM before the STOP instruction is executed to place the MCU in stop2 mode. Upon recovery from stop2 mode, before accessing any I/O, the user should examine the state of the PPDF bit in the SPMSC2 register. If the PPDF bit is 0, I/O must be initialized as if a power on reset had occurred. If the PPDF bit is 1, peripherals may require initialization to be restored to their pre-stop condition. This can be done using data previously stored in RAM if it was saved before the STOP instruction was executed. The user must then write a 1 to the PPDACK bit in the SPMSC2 register. Access to I/O is now permitted again in the user application program. * In stop3 mode, all I/O is maintained because internal logic circuity stays powered up. Upon recovery, normal I/O function is available to the user. MC9S08DZ60 Series Data Sheet, Rev. 4 88 Freescale Semiconductor Chapter 6 Parallel Input/Output Control 6.5 Parallel I/O and Pin Control Registers This section provides information about the registers associated with the parallel I/O ports. The data and data direction registers are located in page zero of the memory map. The pull up, slew rate, drive strength, and interrupt control registers are located in the high page section of the memory map. Refer to tables in Chapter 4, "Memory," for the absolute address assignments for all parallel I/O and their pin control registers. This section refers to registers and control bits only by their names. A Freescale Semiconductor-provided equate or header file normally is used to translate these names into the appropriate absolute addresses. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 89 Chapter 6 Parallel Input/Output Control 6.5.1 Port A Registers Port A is controlled by the registers listed below. 6.5.1.1 Port A Data Register (PTAD) 7 6 5 4 3 2 1 0 PTAD7 PTAD6 PTAD5 PTAD4 PTAD3 PTAD2 PTAD1 PTAD0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-3. Port A Data Register (PTAD) Table 6-1. PTAD Register Field Descriptions Field Description 7:0 PTAD[7:0] Port A Data Register Bits -- For port A pins that are inputs, reads return the logic level on the pin. For port A pins that are configured as outputs, reads return the last value written to this register. Writes are latched into all bits of this register. For port A pins that are configured as outputs, the logic level is driven out the corresponding MCU pin. Reset forces PTAD to all 0s, but these 0s are not driven out the corresponding pins because reset also configures all port pins as high-impedance inputs with pull-ups/pull-downs disabled. 6.5.1.2 Port A Data Direction Register (PTADD) 7 6 5 4 3 2 1 0 PTADD7 PTADD6 PTADD5 PTADD4 PTADD3 PTADD2 PTADD1 PTADD0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-4. Port A Data Direction Register (PTADD) Table 6-2. PTADD Register Field Descriptions Field Description 7:0 Data Direction for Port A Bits -- These read/write bits control the direction of port A pins and what is read for PTADD[7:0] PTAD reads. 0 Input (output driver disabled) and reads return the pin value. 1 Output driver enabled for port A bit n and PTAD reads return the contents of PTADn. MC9S08DZ60 Series Data Sheet, Rev. 4 90 Freescale Semiconductor Chapter 6 Parallel Input/Output Control 6.5.1.3 Port A Pull Enable Register (PTAPE) 7 6 5 4 3 2 1 0 PTAPE7 PTAPE6 PTAPE5 PTAPE4 PTAPE3 PTAPE2 PTAPE1 PTAPE0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-5. Internal Pull Enable for Port A Register (PTAPE) Table 6-3. PTAPE Register Field Descriptions Field Description 7:0 Internal Pull Enable for Port A Bits -- Each of these control bits determines if the internal pull-up or pull-down PTAPE[7:0] device is enabled for the associated PTA pin. For port A pins that are configured as outputs, these bits have no effect and the internal pull devices are disabled. 0 Internal pull-up/pull-down device disabled for port A bit n. 1 Internal pull-up/pull-down device enabled for port A bit n. NOTE Pull-down devices only apply when using pin interrupt functions, when corresponding edge select and pin select functions are configured. 6.5.1.4 Port A Slew Rate Enable Register (PTASE) 7 6 5 4 3 2 1 0 PTASE7 PTASE6 PTASE5 PTASE4 PTASE3 PTASE2 PTASE1 PTASE0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-6. Slew Rate Enable for Port A Register (PTASE) Table 6-4. PTASE Register Field Descriptions Field Description 7:0 Output Slew Rate Enable for Port A Bits -- Each of these control bits determines if the output slew rate control PTASE[7:0] is enabled for the associated PTA pin. For port A pins that are configured as inputs, these bits have no effect. 0 Output slew rate control disabled for port A bit n. 1 Output slew rate control enabled for port A bit n. Note: Slew rate reset default values may differ between engineering samples and final production parts. Always initialize slew rate control to the desired value to ensure correct operation. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 91 Chapter 6 Parallel Input/Output Control 6.5.1.5 Port A Drive Strength Selection Register (PTADS) 7 6 5 4 3 2 1 0 PTADS7 PTADS6 PTADS5 PTADS4 PTADS3 PTADS2 PTADS1 PTADS0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-7. Drive Strength Selection for Port A Register (PTADS) Table 6-5. PTADS Register Field Descriptions Field Description 7:0 Output Drive Strength Selection for Port A Bits -- Each of these control bits selects between low and high PTADS[7:0] output drive for the associated PTA pin. For port A pins that are configured as inputs, these bits have no effect. 0 Low output drive strength selected for port A bit n. 1 High output drive strength selected for port A bit n. 6.5.1.6 R Port A Interrupt Status and Control Register (PTASC) 7 6 5 4 3 2 0 0 0 0 PTAIF 0 W Reset: 1 0 PTAIE PTAMOD 0 0 PTAACK 0 0 0 0 0 0 = Unimplemented or Reserved Figure 6-8. Port A Interrupt Status and Control Register (PTASC) Table 6-6. PTASC Register Field Descriptions Field Description 3 PTAIF Port A Interrupt Flag -- PTAIF indicates when a port A interrupt is detected. Writes have no effect on PTAIF. 0 No port A interrupt detected. 1 Port A interrupt detected. 2 PTAACK 1 PTAIE 0 PTAMOD Port A Interrupt Acknowledge -- Writing a 1 to PTAACK is part of the flag clearing mechanism. PTAACK always reads as 0. Port A Interrupt Enable -- PTAIE determines whether a port A interrupt is requested. 0 Port A interrupt request not enabled. 1 Port A interrupt request enabled. Port A Detection Mode -- PTAMOD (along with the PTAES bits) controls the detection mode of the port A interrupt pins. 0 Port A pins detect edges only. 1 Port A pins detect both edges and levels. MC9S08DZ60 Series Data Sheet, Rev. 4 92 Freescale Semiconductor Chapter 6 Parallel Input/Output Control 6.5.1.7 Port A Interrupt Pin Select Register (PTAPS) 7 6 5 4 3 2 1 0 PTAPS7 PTAPS6 PTAPS5 PTAPS4 PTAPS3 PTAPS2 PTAPS1 PTAPS0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-9. Port A Interrupt Pin Select Register (PTAPS) Table 6-7. PTAPS Register Field Descriptions Field Description 7:0 Port A Interrupt Pin Selects -- Each of the PTAPSn bits enable the corresponding port A interrupt pin. PTAPS[7:0] 0 Pin not enabled as interrupt. 1 Pin enabled as interrupt. 6.5.1.8 Port A Interrupt Edge Select Register (PTAES) 7 6 5 4 3 2 1 0 PTAES7 PTAES6 PTAES5 PTAES4 PTAES3 PTAES2 PTAES1 PTAES0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-10. Port A Edge Select Register (PTAES) Table 6-8. PTAES Register Field Descriptions Field Description 7:0 Port A Edge Selects -- Each of the PTAESn bits serves a dual purpose by selecting the polarity of the active PTAES[7:0] interrupt edge as well as selecting a pull-up or pull-down device if enabled. 0 A pull-up device is connected to the associated pin and detects falling edge/low level for interrupt generation. 1 A pull-down device is connected to the associated pin and detects rising edge/high level for interrupt generation. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 93 Chapter 6 Parallel Input/Output Control 6.5.2 Port B Registers Port B is controlled by the registers listed below. 6.5.2.1 Port B Data Register (PTBD) 7 6 5 4 3 2 1 0 PTBD7 PTBD6 PTBD5 PTBD4 PTBD3 PTBD2 PTBD1 PTBD0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-11. Port B Data Register (PTBD) Table 6-9. PTBD Register Field Descriptions Field Description 7:0 PTBD[7:0] Port B Data Register Bits -- For port B pins that are inputs, reads return the logic level on the pin. For port B pins that are configured as outputs, reads return the last value written to this register. Writes are latched into all bits of this register. For port B pins that are configured as outputs, the logic level is driven out the corresponding MCU pin. Reset forces PTBD to all 0s, but these 0s are not driven out the corresponding pins because reset also configures all port pins as high-impedance inputs with pull-ups/pull-downs disabled. 6.5.2.2 Port B Data Direction Register (PTBDD) 7 6 5 4 3 2 1 0 PTBDD7 PTBDD6 PTBDD5 PTBDD4 PTBDD3 PTBDD2 PTBDD1 PTBDD0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-12. Port B Data Direction Register (PTBDD) Table 6-10. PTBDD Register Field Descriptions Field Description 7:0 Data Direction for Port B Bits -- These read/write bits control the direction of port B pins and what is read for PTBDD[7:0] PTBD reads. 0 Input (output driver disabled) and reads return the pin value. 1 Output driver enabled for port B bit n and PTBD reads return the contents of PTBDn. MC9S08DZ60 Series Data Sheet, Rev. 4 94 Freescale Semiconductor Chapter 6 Parallel Input/Output Control 6.5.2.3 Port B Pull Enable Register (PTBPE) 7 6 5 4 3 2 1 0 PTBPE7 PTBPE6 PTBPE5 PTBPE4 PTBPE3 PTBPE2 PTBPE1 PTBPE0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-13. Internal Pull Enable for Port B Register (PTBPE) Table 6-11. PTBPE Register Field Descriptions Field Description 7:0 Internal Pull Enable for Port B Bits -- Each of these control bits determines if the internal pull-up or pull-down PTBPE[7:0] device is enabled for the associated PTB pin. For port B pins that are configured as outputs, these bits have no effect and the internal pull devices are disabled. 0 Internal pull-up/pull-down device disabled for port B bit n. 1 Internal pull-up/pull-down device enabled for port B bit n. NOTE Pull-down devices only apply when using pin interrupt functions, when corresponding edge select and pin select functions are configured. 6.5.2.4 Port B Slew Rate Enable Register (PTBSE) 7 6 5 4 3 2 1 0 PTBSE7 PTBSE6 PTBSE5 PTBSE4 PTBSE3 PTBSE2 PTBSE1 PTBSE0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-14. Slew Rate Enable for Port B Register (PTBSE) Table 6-12. PTBSE Register Field Descriptions Field Description 7:0 Output Slew Rate Enable for Port B Bits -- Each of these control bits determines if the output slew rate control PTBSE[7:0] is enabled for the associated PTB pin. For port B pins that are configured as inputs, these bits have no effect. 0 Output slew rate control disabled for port B bit n. 1 Output slew rate control enabled for port B bit n. Note: Slew rate reset default values may differ between engineering samples and final production parts. Always initialize slew rate control to the desired value to ensure correct operation. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 95 Chapter 6 Parallel Input/Output Control 6.5.2.5 Port B Drive Strength Selection Register (PTBDS) 7 6 5 4 3 2 1 0 PTBDS7 PTBDS6 PTBDS5 PTBDS4 PTBDS3 PTBDS2 PTBDS1 PTBDS0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-15. Drive Strength Selection for Port B Register (PTBDS) Table 6-13. PTBDS Register Field Descriptions Field Description 7:0 Output Drive Strength Selection for Port B Bits -- Each of these control bits selects between low and high PTBDS[7:0] output drive for the associated PTB pin. For port B pins that are configured as inputs, these bits have no effect. 0 Low output drive strength selected for port B bit n. 1 High output drive strength selected for port B bit n. 6.5.2.6 R Port B Interrupt Status and Control Register (PTBSC) 7 6 5 4 3 2 0 0 0 0 PTBIF 0 W Reset: 1 0 PTBIE PTBMOD 0 0 PTBACK 0 0 0 0 0 0 = Unimplemented or Reserved Figure 6-16. Port B Interrupt Status and Control Register (PTBSC) Table 6-14. PTBSC Register Field Descriptions Field Description 3 PTBIF Port B Interrupt Flag -- PTBIF indicates when a Port B interrupt is detected. Writes have no effect on PTBIF. 0 No Port B interrupt detected. 1 Port B interrupt detected. 2 PTBACK 1 PTBIE 0 PTBMOD Port B Interrupt Acknowledge -- Writing a 1 to PTBACK is part of the flag clearing mechanism. PTBACK always reads as 0. Port B Interrupt Enable -- PTBIE determines whether a port B interrupt is requested. 0 Port B interrupt request not enabled. 1 Port B interrupt request enabled. Port B Detection Mode -- PTBMOD (along with the PTBES bits) controls the detection mode of the port B interrupt pins. 0 Port B pins detect edges only. 1 Port B pins detect both edges and levels. MC9S08DZ60 Series Data Sheet, Rev. 4 96 Freescale Semiconductor Chapter 6 Parallel Input/Output Control 6.5.2.7 Port B Interrupt Pin Select Register (PTBPS) 7 6 5 4 3 2 1 0 PTBPS7 PTBPS6 PTBPS5 PTBPS4 PTBPS3 PTBPS2 PTBPS1 PTBPS0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-17. Port B Interrupt Pin Select Register (PTBPS) Table 6-15. PTBPS Register Field Descriptions Field Description 7:0 Port B Interrupt Pin Selects -- Each of the PTBPSn bits enable the corresponding port B interrupt pin. PTBPS[7:0] 0 Pin not enabled as interrupt. 1 Pin enabled as interrupt. 6.5.2.8 Port B Interrupt Edge Select Register (PTBES) 7 6 5 4 3 2 1 0 PTBES7 PTBES6 PTBES5 PTBES4 PTBES3 PTBES2 PTBES1 PTBES0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-18. Port B Edge Select Register (PTBES) Table 6-16. PTBES Register Field Descriptions Field Description 7:0 Port B Edge Selects -- Each of the PTBESn bits serves a dual purpose by selecting the polarity of the active PTBES[7:0] interrupt edge as well as selecting a pull-up or pull-down device if enabled. 0 A pull-up device is connected to the associated pin and detects falling edge/low level for interrupt generation. 1 A pull-down device is connected to the associated pin and detects rising edge/high level for interrupt generation. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 97 Chapter 6 Parallel Input/Output Control 6.5.3 Port C Registers Port C is controlled by the registers listed below. 6.5.3.1 Port C Data Register (PTCD) 7 6 5 4 3 2 1 0 PTCD7 PTCD6 PTCD5 PTCD4 PTCD3 PTCD2 PTCD1 PTCD0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-19. Port C Data Register (PTCD) Table 6-17. PTCD Register Field Descriptions Field Description 7:0 PTCD[7:0] Port C Data Register Bits -- For port C pins that are inputs, reads return the logic level on the pin. For port C pins that are configured as outputs, reads return the last value written to this register. Writes are latched into all bits of this register. For port C pins that are configured as outputs, the logic level is driven out the corresponding MCU pin. Reset forces PTCD to all 0s, but these 0s are not driven out the corresponding pins because reset also configures all port pins as high-impedance inputs with pull-ups disabled. 6.5.3.2 Port C Data Direction Register (PTCDD) 7 6 5 4 3 2 1 0 PTCDD7 PTCDD6 PTCDD5 PTCDD4 PTCDD3 PTCDD2 PTCDD1 PTCDD0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-20. Port C Data Direction Register (PTCDD) Table 6-18. PTCDD Register Field Descriptions Field Description 7:0 Data Direction for Port C Bits -- These read/write bits control the direction of port C pins and what is read for PTCDD[7:0] PTCD reads. 0 Input (output driver disabled) and reads return the pin value. 1 Output driver enabled for port C bit n and PTCD reads return the contents of PTCDn. MC9S08DZ60 Series Data Sheet, Rev. 4 98 Freescale Semiconductor Chapter 6 Parallel Input/Output Control 6.5.3.3 Port C Pull Enable Register (PTCPE) 7 6 5 4 3 2 1 0 PTCPE7 PTCPE6 PTCPE5 PTCPE4 PTCPE3 PTCPE2 PTCPE1 PTCPE0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-21. Internal Pull Enable for Port C Register (PTCPE) Table 6-19. PTCPE Register Field Descriptions Field Description 7:0 Internal Pull Enable for Port C Bits -- Each of these control bits determines if the internal pull-up device is PTCPE[7:0] enabled for the associated PTC pin. For port C pins that are configured as outputs, these bits have no effect and the internal pull devices are disabled. 0 Internal pull-up device disabled for port C bit n. 1 Internal pull-up device enabled for port C bit n. NOTE Pull-down devices only apply when using pin interrupt functions, when corresponding edge select and pin select functions are configured. 6.5.3.4 Port C Slew Rate Enable Register (PTCSE) 7 6 5 4 3 2 1 0 PTCSE7 PTCSE6 PTCSE5 PTCSE4 PTCSE3 PTCSE2 PTCSE1 PTCSE0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-22. Slew Rate Enable for Port C Register (PTCSE) Table 6-20. PTCSE Register Field Descriptions Field Description 7:0 Output Slew Rate Enable for Port C Bits -- Each of these control bits determines if the output slew rate control PTCSE[7:0] is enabled for the associated PTC pin. For port C pins that are configured as inputs, these bits have no effect. 0 Output slew rate control disabled for port C bit n. 1 Output slew rate control enabled for port C bit n. Note: Slew rate reset default values may differ between engineering samples and final production parts. Always initialize slew rate control to the desired value to ensure correct operation. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 99 Chapter 6 Parallel Input/Output Control 6.5.3.5 Port C Drive Strength Selection Register (PTCDS) 7 6 5 4 3 2 1 0 PTCDS7 PTCDS6 PTCDS5 PTCDS4 PTCDS3 PTCDS2 PTCDS1 PTCDS0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-23. Drive Strength Selection for Port C Register (PTCDS) Table 6-21. PTCDS Register Field Descriptions Field Description 7:0 Output Drive Strength Selection for Port C Bits -- Each of these control bits selects between low and high PTCDS[7:0] output drive for the associated PTC pin. For port C pins that are configured as inputs, these bits have no effect. 0 Low output drive strength selected for port C bit n. 1 High output drive strength selected for port C bit n. MC9S08DZ60 Series Data Sheet, Rev. 4 100 Freescale Semiconductor Chapter 6 Parallel Input/Output Control 6.5.4 Port D Registers Port D is controlled by the registers listed below. 6.5.4.1 Port D Data Register (PTDD) 7 6 5 4 3 2 1 0 PTDD7 PTDD6 PTDD5 PTDD4 PTDD3 PTDD2 PTDD1 PTDD0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-24. Port D Data Register (PTDD) Table 6-22. PTDD Register Field Descriptions Field Description 7:0 PTDD[7:0] Port D Data Register Bits -- For port D pins that are inputs, reads return the logic level on the pin. For port D pins that are configured as outputs, reads return the last value written to this register. Writes are latched into all bits of this register. For port D pins that are configured as outputs, the logic level is driven out the corresponding MCU pin. Reset forces PTDD to all 0s, but these 0s are not driven out the corresponding pins because reset also configures all port pins as high-impedance inputs with pull-ups/pull-downs disabled. 6.5.4.2 Port D Data Direction Register (PTDDD) 7 6 5 4 3 2 1 0 PTDDD7 PTDDD6 PTDDD5 PTDDD4 PTDDD3 PTDDD2 PTDDD1 PTDDD0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-25. Port D Data Direction Register (PTDDD) Table 6-23. PTDDD Register Field Descriptions Field Description 7:0 Data Direction for Port D Bits -- These read/write bits control the direction of port D pins and what is read for PTDDD[7:0] PTDD reads. 0 Input (output driver disabled) and reads return the pin value. 1 Output driver enabled for port D bit n and PTDD reads return the contents of PTDDn. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 101 Chapter 6 Parallel Input/Output Control 6.5.4.3 Port D Pull Enable Register (PTDPE) 7 6 5 4 3 2 1 0 PTDPE7 PTDPE6 PTDPE5 PTDPE4 PTDPE3 PTDPE2 PTDPE1 PTDPE0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-26. Internal Pull Enable for Port D Register (PTDPE) Table 6-24. PTDPE Register Field Descriptions Field Description 7:0 Internal Pull Enable for Port D Bits -- Each of these control bits determines if the internal pull-up or pull-down PTDPE[7:0] device is enabled for the associated PTD pin. For port D pins that are configured as outputs, these bits have no effect and the internal pull devices are disabled. 0 Internal pull-up/pull-down device disabled for port D bit n. 1 Internal pull-up/pull-down device enabled for port D bit n. NOTE Pull-down devices only apply when using pin interrupt functions, when corresponding edge select and pin select functions are configured. 6.5.4.4 Port D Slew Rate Enable Register (PTDSE) 7 6 5 4 3 2 1 0 PTDSE7 PTDSE6 PTDSE5 PTDSE4 PTDSE3 PTDSE2 PTDSE1 PTDSE0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-27. Slew Rate Enable for Port D Register (PTDSE) Table 6-25. PTDSE Register Field Descriptions Field Description 7:0 Output Slew Rate Enable for Port D Bits -- Each of these control bits determines if the output slew rate control PTDSE[7:0] is enabled for the associated PTD pin. For port D pins that are configured as inputs, these bits have no effect. 0 Output slew rate control disabled for port D bit n. 1 Output slew rate control enabled for port D bit n. Note: Slew rate reset default values may differ between engineering samples and final production parts. Always initialize slew rate control to the desired value to ensure correct operation. MC9S08DZ60 Series Data Sheet, Rev. 4 102 Freescale Semiconductor Chapter 6 Parallel Input/Output Control 6.5.4.5 Port D Drive Strength Selection Register (PTDDS) 7 6 5 4 3 2 1 0 PTDDS7 PTDDS6 PTDDS5 PTDDS4 PTDDS3 PTDDS2 PTDDS1 PTDDS0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-28. Drive Strength Selection for Port D Register (PTDDS) Table 6-26. PTDDS Register Field Descriptions Field Description 7:0 Output Drive Strength Selection for Port D Bits -- Each of these control bits selects between low and high PTDDS[7:0] output drive for the associated PTD pin. For port D pins that are configured as inputs, these bits have no effect. 0 Low output drive strength selected for port D bit n. 1 High output drive strength selected for port D bit n. 6.5.4.6 R Port D Interrupt Status and Control Register (PTDSC) 7 6 5 4 3 2 0 0 0 0 PTDIF 0 W Reset: 1 0 PTDIE PTDMOD 0 0 PTDACK 0 0 0 0 0 0 = Unimplemented or Reserved Figure 6-29. Port D Interrupt Status and Control Register (PTDSC) Table 6-27. PTDSC Register Field Descriptions Field Description 3 PTDIF Port D Interrupt Flag -- PTDIF indicates when a port D interrupt is detected. Writes have no effect on PTDIF. 0 No port D interrupt detected. 1 Port D interrupt detected. 2 PTDACK 1 PTDIE 0 PTDMOD Port D Interrupt Acknowledge -- Writing a 1 to PTDACK is part of the flag clearing mechanism. PTDACK always reads as 0. Port D Interrupt Enable -- PTDIE determines whether a port D interrupt is requested. 0 Port D interrupt request not enabled. 1 Port D interrupt request enabled. Port A Detection Mode -- PTDMOD (along with the PTDES bits) controls the detection mode of the port D interrupt pins. 0 Port D pins detect edges only. 1 Port D pins detect both edges and levels. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 103 Chapter 6 Parallel Input/Output Control 6.5.4.7 Port D Interrupt Pin Select Register (PTDPS) 7 6 5 4 3 2 1 0 PTDPS7 PTDPS6 PTDPS5 PTDPS4 PTDPS3 PTDPS2 PTDPS1 PTDPS0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-30. Port D Interrupt Pin Select Register (PTDPS) Table 6-28. PTDPS Register Field Descriptions Field Description 7:0 Port D Interrupt Pin Selects -- Each of the PTDPSn bits enable the corresponding port D interrupt pin. PTDPS[7:0] 0 Pin not enabled as interrupt. 1 Pin enabled as interrupt. 6.5.4.8 Port D Interrupt Edge Select Register (PTDES) 7 6 5 4 3 2 1 0 PTDES7 PTDES6 PTDES5 PTDES4 PTDES3 PTDES2 PTDES1 PTDES0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-31. Port D Edge Select Register (PTDES) Table 6-29. PTDES Register Field Descriptions Field Description 7:0 Port D Edge Selects -- Each of the PTDESn bits serves a dual purpose by selecting the polarity of the active PTDES[7:0] interrupt edge as well as selecting a pull-up or pull-down device if enabled. 0 A pull-up device is connected to the associated pin and detects falling edge/low level for interrupt generation. 1 A pull-down device is connected to the associated pin and detects rising edge/high level for interrupt generation. MC9S08DZ60 Series Data Sheet, Rev. 4 104 Freescale Semiconductor Chapter 6 Parallel Input/Output Control 6.5.5 Port E Registers Port E is controlled by the registers listed below. 6.5.5.1 Port E Data Register (PTED) 7 6 5 4 3 2 1 0 PTED7 PTED6 PTED5 PTED4 PTED3 PTED2 PTED11 PTED0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-32. Port E Data Register (PTED) 1 Reads of this bit always return the pin value of the associated pin, regardless of the value stored in the port data direction bit. Table 6-30. PTED Register Field Descriptions Field Description 7:0 PTED[7:0] Port E Data Register Bits -- For port E pins that are inputs, reads return the logic level on the pin. For port E pins that are configured as outputs, reads return the last value written to this register. Writes are latched into all bits of this register. For port E pins that are configured as outputs, the logic level is driven out the corresponding MCU pin. Reset forces PTED to all 0s, but these 0s are not driven out the corresponding pins because reset also configures all port pins as high-impedance inputs with pull-ups disabled. 6.5.5.2 Port E Data Direction Register (PTEDD) 7 6 5 4 3 2 1 0 PTEDD7 PTEDD6 PTEDD5 PTEDD4 PTEDD3 PTEDD2 PTEDD11 PTEDD0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-33. Port E Data Direction Register (PTEDD) 1 PTEDD1 has no effect on the input-only PTE1 pin. Table 6-31. PTEDD Register Field Descriptions Field Description 7:0 Data Direction for Port E Bits -- These read/write bits control the direction of port E pins and what is read for PTEDD[7:0] PTED reads. 0 Input (output driver disabled) and reads return the pin value. 1 Output driver enabled for port E bit n and PTED reads return the contents of PTEDn. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 105 Chapter 6 Parallel Input/Output Control 6.5.5.3 Port E Pull Enable Register (PTEPE) 7 6 5 4 3 2 1 0 PTEPE7 PTEPE6 PTEPE5 PTEPE4 PTEPE3 PTEPE2 PTEPE1 PTEPE0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-34. Internal Pull Enable for Port E Register (PTEPE) Table 6-32. PTEPE Register Field Descriptions Field Description 7:0 Internal Pull Enable for Port E Bits -- Each of these control bits determines if the internal pull-up device is PTEPE[7:0] enabled for the associated PTE pin. For port E pins that are configured as outputs, these bits have no effect and the internal pull devices are disabled. 0 Internal pull-up device disabled for port E bit n. 1 Internal pull-up device enabled for port E bit n. NOTE Pull-down devices only apply when using pin interrupt functions, when corresponding edge select and pin select functions are configured. 6.5.5.4 Port E Slew Rate Enable Register (PTESE) 7 6 5 4 3 2 1 0 PTESE7 PTESE6 PTESE5 PTESE4 PTESE3 PTESE2 PTESE11 PTESE0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-35. Slew Rate Enable for Port E Register (PTESE) 1 PTESE1 has no effect on the input-only PTE1 pin. Table 6-33. PTESE Register Field Descriptions Field Description 7:0 Output Slew Rate Enable for Port E Bits -- Each of these control bits determines if the output slew rate control PTESE[7:0] is enabled for the associated PTE pin. For port E pins that are configured as inputs, these bits have no effect. 0 Output slew rate control disabled for port E bit n. 1 Output slew rate control enabled for port E bit n. Note: Slew rate reset default values may differ between engineering samples and final production parts. Always initialize slew rate control to the desired value to ensure correct operation. MC9S08DZ60 Series Data Sheet, Rev. 4 106 Freescale Semiconductor Chapter 6 Parallel Input/Output Control 6.5.5.5 Port E Drive Strength Selection Register (PTEDS) 7 6 5 4 3 2 1 0 PTEDS7 PTEDS6 PTEDS5 PTEDS4 PTEDS3 PTEDS2 PTEDS11 PTEDS0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-36. Drive Strength Selection for Port E Register (PTEDS) 1 PTEDS1 has no effect on the input-only PTE1 pin. Table 6-34. PTEDS Register Field Descriptions Field Description 7:0 Output Drive Strength Selection for Port E Bits -- Each of these control bits selects between low and high PTEDS[7:0] output drive for the associated PTE pin. For port E pins that are configured as inputs, these bits have no effect. 0 Low output drive strength selected for port E bit n. 1 High output drive strength selected for port E bit n. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 107 Chapter 6 Parallel Input/Output Control 6.5.6 Port F Registers Port F is controlled by the registers listed below. 6.5.6.1 Port F Data Register (PTFD) 7 6 5 4 3 2 1 0 PTFD7 PTFD6 PTFD5 PTFD4 PTFD3 PTFD2 PTFD1 PTFD0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-37. Port F Data Register (PTFD) Table 6-35. PTFD Register Field Descriptions Field Description 7:0 PTFD[7:0] Port F Data Register Bits -- For port F pins that are inputs, reads return the logic level on the pin. For port F pins that are configured as outputs, reads return the last value written to this register. Writes are latched into all bits of this register. For port F pins that are configured as outputs, the logic level is driven out the corresponding MCU pin. Reset forces PTFD to all 0s, but these 0s are not driven out the corresponding pins because reset also configures all port pins as high-impedance inputs with pull-ups disabled. 6.5.6.2 Port F Data Direction Register (PTFDD) 7 6 5 4 3 2 1 0 PTFDD7 PTFDD6 PTFDD5 PTFDD4 PTFDD3 PTFDD2 PTFDD1 PTFDD0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-38. Port F Data Direction Register (PTFDD) Table 6-36. PTFDD Register Field Descriptions Field Description 7:0 Data Direction for Port F Bits -- These read/write bits control the direction of port F pins and what is read for PTFDD[7:0] PTFD reads. 0 Input (output driver disabled) and reads return the pin value. 1 Output driver enabled for port F bit n and PTFD reads return the contents of PTFDn. MC9S08DZ60 Series Data Sheet, Rev. 4 108 Freescale Semiconductor Chapter 6 Parallel Input/Output Control 6.5.6.3 Port F Pull Enable Register (PTFPE) 7 6 5 4 3 2 1 0 PTFPE7 PTFPE6 PTFPE5 PTFPE4 PTFPE3 PTFPE2 PTFPE1 PTFPE0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-39. Internal Pull Enable for Port F Register (PTFPE) Table 6-37. PTFPE Register Field Descriptions Field Description 7:0 Internal Pull Enable for Port F Bits -- Each of these control bits determines if the internal pull-up device is PTFPE[7:0] enabled for the associated PTF pin. For port F pins that are configured as outputs, these bits have no effect and the internal pull devices are disabled. 0 Internal pull-up device disabled for port F bit n. 1 Internal pull-up device enabled for port F bit n. NOTE Pull-down devices only apply when using pin interrupt functions, when corresponding edge select and pin select functions are configured. 6.5.6.4 Port F Slew Rate Enable Register (PTFSE) 7 6 5 4 3 2 1 0 PTFSE7 PTFSE6 PTFSE5 PTFSE4 PTFSE3 PTFSE2 PTFSE1 PTFSE0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-40. Slew Rate Enable for Port F Register (PTFSE) Table 6-38. PTFSE Register Field Descriptions Field Description 7:0 Output Slew Rate Enable for Port F Bits -- Each of these control bits determines if the output slew rate control PTFSE[7:0] is enabled for the associated PTF pin. For port F pins that are configured as inputs, these bits have no effect. 0 Output slew rate control disabled for port F bit n. 1 Output slew rate control enabled for port F bit n. Note: Slew rate reset default values may differ between engineering samples and final production parts. Always initialize slew rate control to the desired value to ensure correct operation. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 109 Chapter 6 Parallel Input/Output Control 6.5.6.5 Port F Drive Strength Selection Register (PTFDS) 7 6 5 4 3 2 1 0 PTFDS7 PTFDS6 PTFDS5 PTFDS4 PTFDS3 PTFDS2 PTFDS1 PTFDS0 0 0 0 0 0 0 0 0 R W Reset: Figure 6-41. Drive Strength Selection for Port F Register (PTFDS) Table 6-39. PTFDS Register Field Descriptions Field Description 7:0 Output Drive Strength Selection for Port F Bits -- Each of these control bits selects between low and high PTFDS[7:0] output drive for the associated PTF pin. For port F pins that are configured as inputs, these bits have no effect. 0 Low output drive strength selected for port F bit n. 1 High output drive strength selected for port F bit n. MC9S08DZ60 Series Data Sheet, Rev. 4 110 Freescale Semiconductor Chapter 6 Parallel Input/Output Control 6.5.7 Port G Registers Port G is controlled by the registers listed below. 6.5.7.1 R Port G Data Register (PTGD) 7 6 0 0 5 4 3 2 1 0 PTGD5 PTGD4 PTGD3 PTGD2 PTGD1 PTGD0 0 0 0 0 0 0 W Reset: 0 0 = Unimplemented or Reserved Figure 6-42. Port G Data Register (PTGD) Table 6-40. PTGD Register Field Descriptions Field Description 5:0 PTGD[5:0] Port G Data Register Bits -- For port G pins that are inputs, reads return the logic level on the pin. For port G pins that are configured as outputs, reads return the last value written to this register. Writes are latched into all bits of this register. For port G pins that are configured as outputs, the logic level is driven out the corresponding MCU pin. Reset forces PTGD to all 0s, but these 0s are not driven out the corresponding pins because reset also configures all port pins as high-impedance inputs with pull-ups disabled. 6.5.7.2 R Port G Data Direction Register (PTGDD) 7 6 0 0 5 4 3 2 1 0 PTGDD5 PTGDD4 PTGDD3 PTGDD2 PTGDD1 PTGDD0 0 0 0 0 0 0 W Reset: 0 0 = Unimplemented or Reserved Figure 6-43. Port G Data Direction Register (PTGDD) Table 6-41. PTGDD Register Field Descriptions Field Description 5:0 Data Direction for Port G Bits -- These read/write bits control the direction of port G pins and what is read for PTGDD[5:0] PTGD reads. 0 Input (output driver disabled) and reads return the pin value. 1 Output driver enabled for port G bit n and PTGD reads return the contents of PTGDn. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 111 Chapter 6 Parallel Input/Output Control 6.5.7.3 R Port G Pull Enable Register (PTGPE) 7 6 0 0 5 4 3 2 1 0 PTGPE5 PTGPE4 PTGPE3 PTGPE2 PTGPE1 PTGPE0 0 0 0 0 0 0 W Reset: 0 0 = Unimplemented or Reserved Figure 6-44. Internal Pull Enable for Port G Register (PTGPE) Table 6-42. PTGPE Register Field Descriptions Field Description 5:0 Internal Pull Enable for Port G Bits -- Each of these control bits determines if the internal pull-up device is PTGPE[5:0] enabled for the associated PTG pin. For port G pins that are configured as outputs, these bits have no effect and the internal pull devices are disabled. 0 Internal pull-up device disabled for port G bit n. 1 Internal pull-up device enabled for port G bit n. NOTE Pull-down devices only apply when using pin interrupt functions, when corresponding edge select and pin select functions are configured. 6.5.7.4 R Port G Slew Rate Enable Register (PTGSE) 7 6 0 0 5 4 3 2 1 0 PTGSE5 PTGSE4 PTGSE3 PTGSE2 PTGSE1 PTGSE0 0 0 0 0 0 0 W Reset: 0 0 = Unimplemented or Reserved Figure 6-45. Slew Rate Enable for Port G Register (PTGSE) Table 6-43. PTGSE Register Field Descriptions Field Description 5:0 Output Slew Rate Enable for Port G Bits -- Each of these control bits determines if the output slew rate control PTGSE[5:0] is enabled for the associated PTG pin. For port G pins that are configured as inputs, these bits have no effect. 0 Output slew rate control disabled for port G bit n. 1 Output slew rate control enabled for port G bit n. Note: Slew rate reset default values may differ between engineering samples and final production parts. Always initialize slew rate control to the desired value to ensure correct operation. MC9S08DZ60 Series Data Sheet, Rev. 4 112 Freescale Semiconductor Chapter 6 Parallel Input/Output Control 6.5.7.5 R Port G Drive Strength Selection Register (PTGDS) 7 6 0 0 5 4 3 2 1 0 PTGDS5 PTGDS4 PTGDS3 PTGDS2 PTGDS1 PTGDS0 0 0 0 0 0 0 W Reset: 0 0 = Unimplemented or Reserved Figure 6-46. Drive Strength Selection for Port G Register (PTGDS) Table 6-44. PTGDS Register Field Descriptions Field Description 5:0 Output Drive Strength Selection for Port G Bits -- Each of these control bits selects between low and high PTGDS[5:0 output drive for the associated PTG pin. For port G pins that are configured as inputs, these bits have no effect. 0 Low output drive strength selected for port G bit n. 1 High output drive strength selected for port G bit n. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 113 Chapter 6 Parallel Input/Output Control MC9S08DZ60 Series Data Sheet, Rev. 4 114 Freescale Semiconductor Chapter 7 Central Processor Unit (S08CPUV3) 7.1 Introduction This section provides summary information about the registers, addressing modes, and instruction set of the CPU of the HCS08 Family. For a more detailed discussion, refer to the HCS08 Family Reference Manual, volume 1, Freescale Semiconductor document order number HCS08RMV1/D. The HCS08 CPU is fully source- and object-code-compatible with the M68HC08 CPU. Several instructions and enhanced addressing modes were added to improve C compiler efficiency and to support a new background debug system which replaces the monitor mode of earlier M68HC08 microcontrollers (MCU). 7.1.1 Features Features of the HCS08 CPU include: * Object code fully upward-compatible with M68HC05 and M68HC08 Families * All registers and memory are mapped to a single 64-Kbyte address space * 16-bit stack pointer (any size stack anywhere in 64-Kbyte address space) * 16-bit index register (H:X) with powerful indexed addressing modes * 8-bit accumulator (A) * Many instructions treat X as a second general-purpose 8-bit register * Seven addressing modes: -- Inherent -- Operands in internal registers -- Relative -- 8-bit signed offset to branch destination -- Immediate -- Operand in next object code byte(s) -- Direct -- Operand in memory at 0x0000-0x00FF -- Extended -- Operand anywhere in 64-Kbyte address space -- Indexed relative to H:X -- Five submodes including auto increment -- Indexed relative to SP -- Improves C efficiency dramatically * Memory-to-memory data move instructions with four address mode combinations * Overflow, half-carry, negative, zero, and carry condition codes support conditional branching on the results of signed, unsigned, and binary-coded decimal (BCD) operations * Efficient bit manipulation instructions * Fast 8-bit by 8-bit multiply and 16-bit by 8-bit divide instructions * STOP and WAIT instructions to invoke low-power operating modes MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 115 Chapter 7 Central Processor Unit (S08CPUV3) 7.2 Programmer's Model and CPU Registers Figure 7-1 shows the five CPU registers. CPU registers are not part of the memory map. 7 0 ACCUMULATOR A 16-BIT INDEX REGISTER H:X H INDEX REGISTER (HIGH) 8 15 INDEX REGISTER (LOW) 7 X 0 SP STACK POINTER 0 15 PROGRAM COUNTER 7 0 CONDITION CODE REGISTER V 1 1 H I N Z C PC CCR CARRY ZERO NEGATIVE INTERRUPT MASK HALF-CARRY (FROM BIT 3) TWO'S COMPLEMENT OVERFLOW Figure 7-1. CPU Registers 7.2.1 Accumulator (A) The A accumulator is a general-purpose 8-bit register. One operand input to the arithmetic logic unit (ALU) is connected to the accumulator and the ALU results are often stored into the A accumulator after arithmetic and logical operations. The accumulator can be loaded from memory using various addressing modes to specify the address where the loaded data comes from, or the contents of A can be stored to memory using various addressing modes to specify the address where data from A will be stored. Reset has no effect on the contents of the A accumulator. 7.2.2 Index Register (H:X) This 16-bit register is actually two separate 8-bit registers (H and X), which often work together as a 16-bit address pointer where H holds the upper byte of an address and X holds the lower byte of the address. All indexed addressing mode instructions use the full 16-bit value in H:X as an index reference pointer; however, for compatibility with the earlier M68HC05 Family, some instructions operate only on the low-order 8-bit half (X). Many instructions treat X as a second general-purpose 8-bit register that can be used to hold 8-bit data values. X can be cleared, incremented, decremented, complemented, negated, shifted, or rotated. Transfer instructions allow data to be transferred from A or transferred to A where arithmetic and logical operations can then be performed. For compatibility with the earlier M68HC05 Family, H is forced to 0x00 during reset. Reset has no effect on the contents of X. MC9S08DZ60 Series Data Sheet, Rev. 4 116 Freescale Semiconductor Chapter 7 Central Processor Unit (S08CPUV3) 7.2.3 Stack Pointer (SP) This 16-bit address pointer register points at the next available location on the automatic last-in-first-out (LIFO) stack. The stack may be located anywhere in the 64-Kbyte address space that has RAM and can be any size up to the amount of available RAM. The stack is used to automatically save the return address for subroutine calls, the return address and CPU registers during interrupts, and for local variables. The AIS (add immediate to stack pointer) instruction adds an 8-bit signed immediate value to SP. This is most often used to allocate or deallocate space for local variables on the stack. SP is forced to 0x00FF at reset for compatibility with the earlier M68HC05 Family. HCS08 programs normally change the value in SP to the address of the last location (highest address) in on-chip RAM during reset initialization to free up direct page RAM (from the end of the on-chip registers to 0x00FF). The RSP (reset stack pointer) instruction was included for compatibility with the M68HC05 Family and is seldom used in new HCS08 programs because it only affects the low-order half of the stack pointer. 7.2.4 Program Counter (PC) The program counter is a 16-bit register that contains the address of the next instruction or operand to be fetched. During normal program execution, the program counter automatically increments to the next sequential memory location every time an instruction or operand is fetched. Jump, branch, interrupt, and return operations load the program counter with an address other than that of the next sequential location. This is called a change-of-flow. During reset, the program counter is loaded with the reset vector that is located at 0xFFFE and 0xFFFF. The vector stored there is the address of the first instruction that will be executed after exiting the reset state. 7.2.5 Condition Code Register (CCR) The 8-bit condition code register contains the interrupt mask (I) and five flags that indicate the results of the instruction just executed. Bits 6 and 5 are set permanently to 1. The following paragraphs describe the functions of the condition code bits in general terms. For a more detailed explanation of how each instruction sets the CCR bits, refer to the HCS08 Family Reference Manual, volume 1, Freescale Semiconductor document order number HCS08RMv1. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 117 Chapter 7 Central Processor Unit (S08CPUV3) 7 0 CONDITION CODE REGISTER V 1 1 H I N Z C CCR CARRY ZERO NEGATIVE INTERRUPT MASK HALF-CARRY (FROM BIT 3) TWO'S COMPLEMENT OVERFLOW Figure 7-2. Condition Code Register Table 7-1. CCR Register Field Descriptions Field Description 7 V Two's Complement Overflow Flag -- The CPU sets the overflow flag when a two's complement overflow occurs. The signed branch instructions BGT, BGE, BLE, and BLT use the overflow flag. 0 No overflow 1 Overflow 4 H Half-Carry Flag -- The CPU sets the half-carry flag when a carry occurs between accumulator bits 3 and 4 during an add-without-carry (ADD) or add-with-carry (ADC) operation. The half-carry flag is required for binary-coded decimal (BCD) arithmetic operations. The DAA instruction uses the states of the H and C condition code bits to automatically add a correction value to the result from a previous ADD or ADC on BCD operands to correct the result to a valid BCD value. 0 No carry between bits 3 and 4 1 Carry between bits 3 and 4 3 I Interrupt Mask Bit -- When the interrupt mask is set, all maskable CPU interrupts are disabled. CPU interrupts are enabled when the interrupt mask is cleared. When a CPU interrupt occurs, the interrupt mask is set automatically after the CPU registers are saved on the stack, but before the first instruction of the interrupt service routine is executed. Interrupts are not recognized at the instruction boundary after any instruction that clears I (CLI or TAP). This ensures that the next instruction after a CLI or TAP will always be executed without the possibility of an intervening interrupt, provided I was set. 0 Interrupts enabled 1 Interrupts disabled 2 N Negative Flag -- The CPU sets the negative flag when an arithmetic operation, logic operation, or data manipulation produces a negative result, setting bit 7 of the result. Simply loading or storing an 8-bit or 16-bit value causes N to be set if the most significant bit of the loaded or stored value was 1. 0 Non-negative result 1 Negative result 1 Z Zero Flag -- The CPU sets the zero flag when an arithmetic operation, logic operation, or data manipulation produces a result of 0x00 or 0x0000. Simply loading or storing an 8-bit or 16-bit value causes Z to be set if the loaded or stored value was all 0s. 0 Non-zero result 1 Zero result 0 C Carry/Borrow Flag -- The CPU sets the carry/borrow flag when an addition operation produces a carry out of bit 7 of the accumulator or when a subtraction operation requires a borrow. Some instructions -- such as bit test and branch, shift, and rotate -- also clear or set the carry/borrow flag. 0 No carry out of bit 7 1 Carry out of bit 7 MC9S08DZ60 Series Data Sheet, Rev. 4 118 Freescale Semiconductor Chapter 7 Central Processor Unit (S08CPUV3) 7.3 Addressing Modes Addressing modes define the way the CPU accesses operands and data. In the HCS08, all memory, status and control registers, and input/output (I/O) ports share a single 64-Kbyte linear address space so a 16-bit binary address can uniquely identify any memory location. This arrangement means that the same instructions that access variables in RAM can also be used to access I/O and control registers or nonvolatile program space. Some instructions use more than one addressing mode. For instance, move instructions use one addressing mode to specify the source operand and a second addressing mode to specify the destination address. Instructions such as BRCLR, BRSET, CBEQ, and DBNZ use one addressing mode to specify the location of an operand for a test and then use relative addressing mode to specify the branch destination address when the tested condition is true. For BRCLR, BRSET, CBEQ, and DBNZ, the addressing mode listed in the instruction set tables is the addressing mode needed to access the operand to be tested, and relative addressing mode is implied for the branch destination. 7.3.1 Inherent Addressing Mode (INH) In this addressing mode, operands needed to complete the instruction (if any) are located within CPU registers so the CPU does not need to access memory to get any operands. 7.3.2 Relative Addressing Mode (REL) Relative addressing mode is used to specify the destination location for branch instructions. A signed 8-bit offset value is located in the memory location immediately following the opcode. During execution, if the branch condition is true, the signed offset is sign-extended to a 16-bit value and is added to the current contents of the program counter, which causes program execution to continue at the branch destination address. 7.3.3 Immediate Addressing Mode (IMM) In immediate addressing mode, the operand needed to complete the instruction is included in the object code immediately following the instruction opcode in memory. In the case of a 16-bit immediate operand, the high-order byte is located in the next memory location after the opcode, and the low-order byte is located in the next memory location after that. 7.3.4 Direct Addressing Mode (DIR) In direct addressing mode, the instruction includes the low-order eight bits of an address in the direct page (0x0000-0x00FF). During execution a 16-bit address is formed by concatenating an implied 0x00 for the high-order half of the address and the direct address from the instruction to get the 16-bit address where the desired operand is located. This is faster and more memory efficient than specifying a complete 16-bit address for the operand. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 119 Chapter 7 Central Processor Unit (S08CPUV3) 7.3.5 Extended Addressing Mode (EXT) In extended addressing mode, the full 16-bit address of the operand is located in the next two bytes of program memory after the opcode (high byte first). 7.3.6 Indexed Addressing Mode Indexed addressing mode has seven variations including five that use the 16-bit H:X index register pair and two that use the stack pointer as the base reference. 7.3.6.1 Indexed, No Offset (IX) This variation of indexed addressing uses the 16-bit value in the H:X index register pair as the address of the operand needed to complete the instruction. 7.3.6.2 Indexed, No Offset with Post Increment (IX+) This variation of indexed addressing uses the 16-bit value in the H:X index register pair as the address of the operand needed to complete the instruction. The index register pair is then incremented (H:X = H:X + 0x0001) after the operand has been fetched. This addressing mode is only used for MOV and CBEQ instructions. 7.3.6.3 Indexed, 8-Bit Offset (IX1) This variation of indexed addressing uses the 16-bit value in the H:X index register pair plus an unsigned 8-bit offset included in the instruction as the address of the operand needed to complete the instruction. 7.3.6.4 Indexed, 8-Bit Offset with Post Increment (IX1+) This variation of indexed addressing uses the 16-bit value in the H:X index register pair plus an unsigned 8-bit offset included in the instruction as the address of the operand needed to complete the instruction. The index register pair is then incremented (H:X = H:X + 0x0001) after the operand has been fetched. This addressing mode is used only for the CBEQ instruction. 7.3.6.5 Indexed, 16-Bit Offset (IX2) This variation of indexed addressing uses the 16-bit value in the H:X index register pair plus a 16-bit offset included in the instruction as the address of the operand needed to complete the instruction. 7.3.6.6 SP-Relative, 8-Bit Offset (SP1) This variation of indexed addressing uses the 16-bit value in the stack pointer (SP) plus an unsigned 8-bit offset included in the instruction as the address of the operand needed to complete the instruction. MC9S08DZ60 Series Data Sheet, Rev. 4 120 Freescale Semiconductor Chapter 7 Central Processor Unit (S08CPUV3) 7.3.6.7 SP-Relative, 16-Bit Offset (SP2) This variation of indexed addressing uses the 16-bit value in the stack pointer (SP) plus a 16-bit offset included in the instruction as the address of the operand needed to complete the instruction. 7.4 Special Operations The CPU performs a few special operations that are similar to instructions but do not have opcodes like other CPU instructions. In addition, a few instructions such as STOP and WAIT directly affect other MCU circuitry. This section provides additional information about these operations. 7.4.1 Reset Sequence Reset can be caused by a power-on-reset (POR) event, internal conditions such as the COP (computer operating properly) watchdog, or by assertion of an external active-low reset pin. When a reset event occurs, the CPU immediately stops whatever it is doing (the MCU does not wait for an instruction boundary before responding to a reset event). For a more detailed discussion about how the MCU recognizes resets and determines the source, refer to the Resets, Interrupts, and System Configuration chapter. The reset event is considered concluded when the sequence to determine whether the reset came from an internal source is done and when the reset pin is no longer asserted. At the conclusion of a reset event, the CPU performs a 6-cycle sequence to fetch the reset vector from 0xFFFE and 0xFFFF and to fill the instruction queue in preparation for execution of the first program instruction. 7.4.2 Interrupt Sequence When an interrupt is requested, the CPU completes the current instruction before responding to the interrupt. At this point, the program counter is pointing at the start of the next instruction, which is where the CPU should return after servicing the interrupt. The CPU responds to an interrupt by performing the same sequence of operations as for a software interrupt (SWI) instruction, except the address used for the vector fetch is determined by the highest priority interrupt that is pending when the interrupt sequence started. The CPU sequence for an interrupt is: 1. Store the contents of PCL, PCH, X, A, and CCR on the stack, in that order. 2. Set the I bit in the CCR. 3. Fetch the high-order half of the interrupt vector. 4. Fetch the low-order half of the interrupt vector. 5. Delay for one free bus cycle. 6. Fetch three bytes of program information starting at the address indicated by the interrupt vector to fill the instruction queue in preparation for execution of the first instruction in the interrupt service routine. After the CCR contents are pushed onto the stack, the I bit in the CCR is set to prevent other interrupts while in the interrupt service routine. Although it is possible to clear the I bit with an instruction in the MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 121 Chapter 7 Central Processor Unit (S08CPUV3) interrupt service routine, this would allow nesting of interrupts (which is not recommended because it leads to programs that are difficult to debug and maintain). For compatibility with the earlier M68HC05 MCUs, the high-order half of the H:X index register pair (H) is not saved on the stack as part of the interrupt sequence. The user must use a PSHH instruction at the beginning of the service routine to save H and then use a PULH instruction just before the RTI that ends the interrupt service routine. It is not necessary to save H if you are certain that the interrupt service routine does not use any instructions or auto-increment addressing modes that might change the value of H. The software interrupt (SWI) instruction is like a hardware interrupt except that it is not masked by the global I bit in the CCR and it is associated with an instruction opcode within the program so it is not asynchronous to program execution. 7.4.3 Wait Mode Operation The WAIT instruction enables interrupts by clearing the I bit in the CCR. It then halts the clocks to the CPU to reduce overall power consumption while the CPU is waiting for the interrupt or reset event that will wake the CPU from wait mode. When an interrupt or reset event occurs, the CPU clocks will resume and the interrupt or reset event will be processed normally. If a serial BACKGROUND command is issued to the MCU through the background debug interface while the CPU is in wait mode, CPU clocks will resume and the CPU will enter active background mode where other serial background commands can be processed. This ensures that a host development system can still gain access to a target MCU even if it is in wait mode. 7.4.4 Stop Mode Operation Usually, all system clocks, including the crystal oscillator (when used), are halted during stop mode to minimize power consumption. In such systems, external circuitry is needed to control the time spent in stop mode and to issue a signal to wake up the target MCU when it is time to resume processing. Unlike the earlier M68HC05 and M68HC08 MCUs, the HCS08 can be configured to keep a minimum set of clocks running in stop mode. This optionally allows an internal periodic signal to wake the target MCU from stop mode. When a host debug system is connected to the background debug pin (BKGD) and the ENBDM control bit has been set by a serial command through the background interface (or because the MCU was reset into active background mode), the oscillator is forced to remain active when the MCU enters stop mode. In this case, if a serial BACKGROUND command is issued to the MCU through the background debug interface while the CPU is in stop mode, CPU clocks will resume and the CPU will enter active background mode where other serial background commands can be processed. This ensures that a host development system can still gain access to a target MCU even if it is in stop mode. Recovery from stop mode depends on the particular HCS08 and whether the oscillator was stopped in stop mode. Refer to the Modes of Operation chapter for more details. MC9S08DZ60 Series Data Sheet, Rev. 4 122 Freescale Semiconductor Chapter 7 Central Processor Unit (S08CPUV3) 7.4.5 BGND Instruction The BGND instruction is new to the HCS08 compared to the M68HC08. BGND would not be used in normal user programs because it forces the CPU to stop processing user instructions and enter the active background mode. The only way to resume execution of the user program is through reset or by a host debug system issuing a GO, TRACE1, or TAGGO serial command through the background debug interface. Software-based breakpoints can be set by replacing an opcode at the desired breakpoint address with the BGND opcode. When the program reaches this breakpoint address, the CPU is forced to active background mode rather than continuing the user program. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 123 Chapter 7 Central Processor Unit (S08CPUV3) 7.5 HCS08 Instruction Set Summary Table 7-2 provides a summary of the HCS08 instruction set in all possible addressing modes. The table shows operand construction, execution time in internal bus clock cycles, and cycle-by-cycle details for each addressing mode variation of each instruction. ADC ADC ADC ADC ADC ADC ADC ADC #opr8i opr8a opr16a oprx16,X oprx8,X ,X oprx16,SP oprx8,SP ADD ADD ADD ADD ADD ADD ADD ADD #opr8i opr8a opr16a oprx16,X oprx8,X ,X oprx16,SP oprx8,SP Operation Add with Carry A (A) + (M) + (C) Add without Carry A (A) + (M) Object Code IMM DIR EXT IX2 IX1 IX SP2 SP1 A9 B9 C9 D9 E9 F9 9E D9 9E E9 ii dd hh ll ee ff ff IMM DIR EXT IX2 IX1 IX SP2 SP1 AB BB CB DB EB FB 9E DB 9E EB ii dd hh ll ee ff ff ee ff ff ee ff ff Cycles Source Form Address Mode Table 7-2. Instruction Set Summary (Sheet 1 of 9) Cyc-by-Cyc Details Affect on CCR V11H INZC 2 3 4 4 3 3 5 4 pp rpp prpp prpp rpp rfp pprpp prpp 1 1 - 2 3 4 4 3 3 5 4 pp rpp prpp prpp rpp rfp pprpp prpp 1 1 - AIS #opr8i Add Immediate Value (Signed) to Stack Pointer SP (SP) + (M) IMM A7 ii 2 pp - 1 1 - - - - - AIX #opr8i Add Immediate Value (Signed) to Index Register (H:X) H:X (H:X) + (M) IMM AF ii 2 pp - 1 1 - - - - - Logical AND A (A) & (M) IMM DIR EXT IX2 IX1 IX SP2 SP1 A4 B4 C4 D4 E4 F4 9E D4 9E E4 2 3 4 4 3 3 5 4 pp rpp prpp prpp rpp rfp pprpp prpp 0 1 1 - - - DIR INH INH IX1 IX SP1 38 dd 48 58 68 ff 78 9E 68 ff 5 1 1 5 4 6 rfwpp p p rfwpp rfwp prfwpp 1 1 - - DIR INH INH IX1 IX SP1 37 dd 47 57 67 ff 77 9E 67 ff 5 1 1 5 4 6 rfwpp p p rfwpp rfwp prfwpp 1 1 - - AND AND AND AND AND AND AND AND #opr8i opr8a opr16a oprx16,X oprx8,X ,X oprx16,SP oprx8,SP ASL opr8a ASLA ASLX ASL oprx8,X ASL ,X ASL oprx8,SP ASR opr8a ASRA ASRX ASR oprx8,X ASR ,X ASR oprx8,SP Arithmetic Shift Left C 0 b7 b0 (Same as LSL) Arithmetic Shift Right C b7 b0 ii dd hh ll ee ff ff ee ff ff MC9S08DZ60 Series Data Sheet, Rev. 4 124 Freescale Semiconductor Chapter 7 Central Processor Unit (S08CPUV3) Operation Object Code Cycles Source Form Address Mode Table 7-2. Instruction Set Summary (Sheet 2 of 9) Cyc-by-Cyc Details Affect on CCR V11H INZC Branch if Carry Bit Clear (if C = 0) REL 24 rr 3 ppp - 1 1 - - - - - BCLR n,opr8a Clear Bit n in Memory (Mn 0) DIR (b0) DIR (b1) DIR (b2) DIR (b3) DIR (b4) DIR (b5) DIR (b6) DIR (b7) 11 13 15 17 19 1B 1D 1F dd dd dd dd dd dd dd dd 5 5 5 5 5 5 5 5 rfwpp rfwpp rfwpp rfwpp rfwpp rfwpp rfwpp rfwpp - 1 1 - - - - - BCS rel Branch if Carry Bit Set (if C = 1) (Same as BLO) REL 25 rr 3 ppp - 1 1 - - - - - BEQ rel Branch if Equal (if Z = 1) REL 27 rr 3 ppp - 1 1 - - - - - BGE rel Branch if Greater Than or Equal To (if N V = 0) (Signed) REL 90 rr 3 ppp - 1 1 - - - - - BGND Enter active background if ENBDM=1 Waits for and processes BDM commands until GO, TRACE1, or TAGGO INH 82 5+ fp...ppp - 1 1 - - - - - BGT rel Branch if Greater Than (if Z | (N V) = 0) (Signed) REL 92 rr 3 ppp - 1 1 - - - - - BHCC rel Branch if Half Carry Bit Clear (if H = 0) REL 28 rr 3 ppp - 1 1 - - - - - BHCS rel Branch if Half Carry Bit Set (if H = 1) REL 29 rr 3 ppp - 1 1 - - - - - BHI rel Branch if Higher (if C | Z = 0) REL 22 rr 3 ppp - 1 1 - - - - - BHS rel Branch if Higher or Same (if C = 0) (Same as BCC) REL 24 rr 3 ppp - 1 1 - - - - - BIH rel Branch if IRQ Pin High (if IRQ pin = 1) REL 2F rr 3 ppp - 1 1 - - - - - BIL rel Branch if IRQ Pin Low (if IRQ pin = 0) REL 2E rr 3 ppp - 1 1 - - - - - Bit Test (A) & (M) (CCR Updated but Operands Not Changed) IMM DIR EXT IX2 IX1 IX SP2 SP1 2 3 4 4 3 3 5 4 pp rpp prpp prpp rpp rfp pprpp prpp 0 1 1 - - - BCC rel BIT BIT BIT BIT BIT BIT BIT BIT #opr8i opr8a opr16a oprx16,X oprx8,X ,X oprx16,SP oprx8,SP A5 B5 C5 D5 E5 F5 9E D5 9E E5 ii dd hh ll ee ff ff ee ff ff BLE rel Branch if Less Than or Equal To (if Z | (N V) = 1) (Signed) REL 93 rr 3 ppp - 1 1 - - - - - BLO rel Branch if Lower (if C = 1) (Same as BCS) REL 25 rr 3 ppp - 1 1 - - - - - BLS rel Branch if Lower or Same (if C | Z = 1) REL 23 rr 3 ppp - 1 1 - - - - - BLT rel Branch if Less Than (if N V = 1) (Signed) REL 91 rr 3 ppp - 1 1 - - - - - BMC rel Branch if Interrupt Mask Clear (if I = 0) REL 2C rr 3 ppp - 1 1 - - - - - BMI rel Branch if Minus (if N = 1) REL 2B rr 3 ppp - 1 1 - - - - - BMS rel Branch if Interrupt Mask Set (if I = 1) REL 2D rr 3 ppp - 1 1 - - - - - BNE rel Branch if Not Equal (if Z = 0) REL 26 rr 3 ppp - 1 1 - - - - - MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 125 Chapter 7 Central Processor Unit (S08CPUV3) Operation Object Code Cycles Source Form Address Mode Table 7-2. Instruction Set Summary (Sheet 3 of 9) Cyc-by-Cyc Details Affect on CCR V11H INZC BPL rel Branch if Plus (if N = 0) REL 2A rr 3 ppp - 1 1 - - - - - BRA rel Branch Always (if I = 1) REL 20 rr 3 ppp - 1 1 - - - - - BRCLR n,opr8a,rel Branch if Bit n in Memory Clear (if (Mn) = 0) DIR (b0) DIR (b1) DIR (b2) DIR (b3) DIR (b4) DIR (b5) DIR (b6) DIR (b7) 01 03 05 07 09 0B 0D 0F 5 5 5 5 5 5 5 5 rpppp rpppp rpppp rpppp rpppp rpppp rpppp rpppp - 1 1 - - - - BRN rel Branch Never (if I = 0) REL 21 rr 3 ppp - 1 1 - - - - - Branch if Bit n in Memory Set (if (Mn) = 1) DIR (b0) DIR (b1) DIR (b2) DIR (b3) DIR (b4) DIR (b5) DIR (b6) DIR (b7) 00 02 04 06 08 0A 0C 0E dd dd dd dd dd dd dd dd 5 5 5 5 5 5 5 5 rpppp rpppp rpppp rpppp rpppp rpppp rpppp rpppp - 1 1 - - - - BSET n,opr8a Set Bit n in Memory (Mn 1) DIR (b0) DIR (b1) DIR (b2) DIR (b3) DIR (b4) DIR (b5) DIR (b6) DIR (b7) 10 12 14 16 18 1A 1C 1E dd dd dd dd dd dd dd dd 5 5 5 5 5 5 5 5 rfwpp rfwpp rfwpp rfwpp rfwpp rfwpp rfwpp rfwpp - 1 1 - - - - - BSR rel Branch to Subroutine PC (PC) + $0002 push (PCL); SP (SP) - $0001 push (PCH); SP (SP) - $0001 PC (PC) + rel REL AD rr 5 ssppp - 1 1 - - - - - 5 4 4 5 5 6 rpppp pppp pppp rpppp rfppp prpppp - 1 1 - - - - - BRSET n,opr8a,rel Branch if (A) = (M) Branch if (A) = (M) Branch if (X) = (M) Branch if (A) = (M) Branch if (A) = (M) Branch if (A) = (M) rr rr rr rr rr rr rr rr rr rr rr rr rr rr rr rr CBEQ opr8a,rel CBEQA #opr8i,rel CBEQX #opr8i,rel CBEQ oprx8,X+,rel CBEQ ,X+,rel CBEQ oprx8,SP,rel Compare and... CLC Clear Carry Bit (C 0) INH 98 1 p - 1 1 - - - - 0 CLI Clear Interrupt Mask Bit (I 0) INH 9A 1 p - 1 1 - 0 - - - CLR opr8a CLRA CLRX CLRH CLR oprx8,X CLR ,X CLR oprx8,SP Clear DIR INH INH INH IX1 IX SP1 3F dd 4F 5F 8C 6F ff 7F 9E 6F ff 5 1 1 1 5 4 6 rfwpp p p p rfwpp rfwp prfwpp 0 1 1 - - 0 1 - M $00 A $00 X $00 H $00 M $00 M $00 M $00 DIR IMM IMM IX1+ IX+ SP1 dd dd dd dd dd dd dd dd 31 41 51 61 71 9E 61 dd ii ii ff rr ff rr rr rr rr rr MC9S08DZ60 Series Data Sheet, Rev. 4 126 Freescale Semiconductor Chapter 7 Central Processor Unit (S08CPUV3) CMP CMP CMP CMP CMP CMP CMP CMP #opr8i opr8a opr16a oprx16,X oprx8,X ,X oprx16,SP oprx8,SP Operation Compare Accumulator with Memory A-M (CCR Updated But Operands Not Changed) Object Code IMM DIR EXT IX2 IX1 IX SP2 SP1 A1 B1 C1 D1 E1 F1 9E D1 9E E1 ii dd hh ll ee ff ff ee ff ff Cycles Source Form Address Mode Table 7-2. Instruction Set Summary (Sheet 4 of 9) Cyc-by-Cyc Details Affect on CCR V11H INZC 2 3 4 4 3 3 5 4 pp rpp prpp prpp rpp rfp pprpp prpp 1 1 - - COM opr8a COMA COMX COM oprx8,X COM ,X COM oprx8,SP Complement M (M)= $FF - (M) (One's Complement) A (A) = $FF - (A) X (X) = $FF - (X) M (M) = $FF - (M) M (M) = $FF - (M) M (M) = $FF - (M) DIR INH INH IX1 IX SP1 33 dd 43 53 63 ff 73 9E 63 ff 5 1 1 5 4 6 rfwpp p p rfwpp rfwp prfwpp 0 1 1 - - 1 CPHX opr16a CPHX #opr16i CPHX opr8a CPHX oprx8,SP Compare Index Register (H:X) with Memory (H:X) - (M:M + $0001) (CCR Updated But Operands Not Changed) EXT IMM DIR SP1 3E 65 75 9E F3 hh ll jj kk dd ff 6 3 5 6 prrfpp ppp rrfpp prrfpp 1 1 - - Compare X (Index Register Low) with Memory X-M (CCR Updated But Operands Not Changed) IMM DIR EXT IX2 IX1 IX SP2 SP1 A3 B3 C3 D3 E3 F3 9E D3 9E E3 ii dd hh ll ee ff ff 2 3 4 4 3 3 5 4 pp rpp prpp prpp rpp rfp pprpp prpp 1 1 - - 1 p U 1 1 - - 7 4 4 7 6 8 rfwpppp fppp fppp rfwpppp rfwppp prfwpppp - 1 1 - - - - - CPX CPX CPX CPX CPX CPX CPX CPX #opr8i opr8a opr16a oprx16,X oprx8,X ,X oprx16,SP oprx8,SP DAA Decimal Adjust Accumulator After ADD or ADC of BCD Values INH 72 DBNZ opr8a,rel DBNZA rel DBNZX rel DBNZ oprx8,X,rel DBNZ ,X,rel DBNZ oprx8,SP,rel DIR INH Decrement A, X, or M and Branch if Not Zero INH (if (result) 0) IX1 DBNZX Affects X Not H IX SP1 3B 4B 5B 6B 7B 9E 6B DEC opr8a DECA DECX DEC oprx8,X DEC ,X DEC oprx8,SP Decrement Divide A (H:A)/(X); H Remainder DIV EOR EOR EOR EOR EOR EOR EOR EOR M (M) - $01 A (A) - $01 X (X) - $01 M (M) - $01 M (M) - $01 M (M) - $01 #opr8i opr8a opr16a oprx16,X oprx8,X ,X oprx16,SP oprx8,SP Exclusive OR Memory with Accumulator A (A M) ee ff ff dd rr rr rr ff rr rr ff rr DIR INH INH IX1 IX SP1 3A dd 4A 5A 6A ff 7A 9E 6A ff 5 1 1 5 4 6 rfwpp p p rfwpp rfwp prfwpp 1 1 - - - INH 52 6 fffffp - 1 1 - - - IMM DIR EXT IX2 IX1 IX SP2 SP1 A8 B8 C8 D8 E8 F8 9E D8 9E E8 2 3 4 4 3 3 5 4 pp rpp prpp prpp rpp rfp pprpp prpp 0 1 1 - - - ii dd hh ll ee ff ff ee ff ff MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 127 Chapter 7 Central Processor Unit (S08CPUV3) INC opr8a INCA INCX INC oprx8,X INC ,X INC oprx8,SP Operation Increment M (M) + $01 A (A) + $01 X (X) + $01 M (M) + $01 M (M) + $01 M (M) + $01 Object Code Cycles Source Form Address Mode Table 7-2. Instruction Set Summary (Sheet 5 of 9) Cyc-by-Cyc Details Affect on CCR V11H INZC DIR INH INH IX1 IX SP1 3C dd 4C 5C 6C ff 7C 9E 6C ff 5 1 1 5 4 6 rfwpp p p rfwpp rfwp prfwpp 1 1 - - - BC CC DC EC FC dd hh ll ee ff ff 3 4 4 3 3 ppp pppp pppp ppp ppp - 1 1 - - - - - JMP JMP JMP JMP JMP opr8a opr16a oprx16,X oprx8,X ,X Jump PC Jump Address DIR EXT IX2 IX1 IX JSR JSR JSR JSR JSR opr8a opr16a oprx16,X oprx8,X ,X Jump to Subroutine PC (PC) + n (n = 1, 2, or 3) Push (PCL); SP (SP) - $0001 Push (PCH); SP (SP) - $0001 PC Unconditional Address DIR EXT IX2 IX1 IX BD CD DD ED FD dd hh ll ee ff ff 5 6 6 5 5 ssppp pssppp pssppp ssppp ssppp - 1 1 - - - - - LDA LDA LDA LDA LDA LDA LDA LDA #opr8i opr8a opr16a oprx16,X oprx8,X ,X oprx16,SP oprx8,SP Load Accumulator from Memory A (M) IMM DIR EXT IX2 IX1 IX SP2 SP1 A6 B6 C6 D6 E6 F6 9E D6 9E E6 ii dd hh ll ee ff ff 2 3 4 4 3 3 5 4 pp rpp prpp prpp rpp rfp pprpp prpp 0 1 1 - - - Load Index Register (H:X) H:X (M:M + $0001) IMM DIR EXT IX IX2 IX1 SP1 jj kk dd hh ll 9E 9E 9E 9E 45 55 32 AE BE CE FE 3 4 5 5 6 5 5 ppp rrpp prrpp prrfp pprrpp prrpp prrpp 0 1 1 - - - Load X (Index Register Low) from Memory X (M) IMM DIR EXT IX2 IX1 IX SP2 SP1 AE BE CE DE EE FE 9E DE 9E EE ii dd hh ll ee ff ff 2 3 4 4 3 3 5 4 pp rpp prpp prpp rpp rfp pprpp prpp 0 1 1 - - - DIR INH INH IX1 IX SP1 38 dd 48 58 68 ff 78 9E 68 ff 5 1 1 5 4 6 rfwpp p p rfwpp rfwp prfwpp 1 1 - - DIR INH INH IX1 IX SP1 34 dd 44 54 64 ff 74 9E 64 ff 5 1 1 5 4 6 rfwpp p p rfwpp rfwp prfwpp 1 1 - - 0 LDHX LDHX LDHX LDHX LDHX LDHX LDHX LDX LDX LDX LDX LDX LDX LDX LDX #opr16i opr8a opr16a ,X oprx16,X oprx8,X oprx8,SP #opr8i opr8a opr16a oprx16,X oprx8,X ,X oprx16,SP oprx8,SP LSL opr8a LSLA LSLX LSL oprx8,X LSL ,X LSL oprx8,SP LSR opr8a LSRA LSRX LSR oprx8,X LSR ,X LSR oprx8,SP Logical Shift Left C 0 b7 b0 (Same as ASL) Logical Shift Right 0 C b7 b0 ee ff ff ee ff ff ff ee ff ff MC9S08DZ60 Series Data Sheet, Rev. 4 128 Freescale Semiconductor Chapter 7 Central Processor Unit (S08CPUV3) Operation Object Code MOV opr8a,opr8a MOV opr8a,X+ MOV #opr8i,opr8a MOV ,X+,opr8a Move (M)destination (M)source In IX+/DIR and DIR/IX+ Modes, H:X (H:X) + $0001 DIR/DIR DIR/IX+ IMM/DIR IX+/DIR 4E 5E 6E 7E MUL Unsigned multiply X:A (X) x (A) INH NEG opr8a NEGA NEGX NEG oprx8,X NEG ,X NEG oprx8,SP Negate M - (M) = $00 - (M) (Two's Complement) A - (A) = $00 - (A) X - (X) = $00 - (X) M - (M) = $00 - (M) M - (M) = $00 - (M) M - (M) = $00 - (M) NOP NSA ORA ORA ORA ORA ORA ORA ORA ORA #opr8i opr8a opr16a oprx16,X oprx8,X ,X oprx16,SP oprx8,SP Cycles Source Form Address Mode Table 7-2. Instruction Set Summary (Sheet 6 of 9) Cyc-by-Cyc Details Affect on CCR V11H INZC 5 5 4 5 rpwpp rfwpp pwpp rfwpp 0 1 1 - - - 42 5 ffffp - 1 1 0 - - - 0 DIR INH INH IX1 IX SP1 30 dd 40 50 60 ff 70 9E 60 ff 5 1 1 5 4 6 rfwpp p p rfwpp rfwp prfwpp 1 1 - - No Operation -- Uses 1 Bus Cycle INH 9D 1 p - 1 1 - - - - - Nibble Swap Accumulator A (A[3:0]:A[7:4]) INH 62 1 p - 1 1 - - - - - Inclusive OR Accumulator and Memory A (A) | (M) IMM DIR EXT IX2 IX1 IX SP2 SP1 AA BA CA DA EA FA 9E DA 9E EA 2 3 4 4 3 3 5 4 pp rpp prpp prpp rpp rfp pprpp prpp 0 1 1 - - - dd dd dd ii dd dd ii dd hh ll ee ff ff ee ff ff PSHA Push Accumulator onto Stack Push (A); SP (SP) - $0001 INH 87 2 sp - 1 1 - - - - - PSHH Push H (Index Register High) onto Stack Push (H); SP (SP) - $0001 INH 8B 2 sp - 1 1 - - - - - PSHX Push X (Index Register Low) onto Stack Push (X); SP (SP) - $0001 INH 89 2 sp - 1 1 - - - - - PULA Pull Accumulator from Stack SP (SP + $0001); Pull (A) INH 86 3 ufp - 1 1 - - - - - PULH Pull H (Index Register High) from Stack SP (SP + $0001); Pull (H) INH 8A 3 ufp - 1 1 - - - - - PULX Pull X (Index Register Low) from Stack SP (SP + $0001); Pull (X) INH 88 3 ufp - 1 1 - - - - - DIR INH INH IX1 IX SP1 39 dd 49 59 69 ff 79 9E 69 ff 5 1 1 5 4 6 rfwpp p p rfwpp rfwp prfwpp 1 1 - - DIR INH INH IX1 IX SP1 36 dd 46 56 66 ff 76 9E 66 ff 5 1 1 5 4 6 rfwpp p p rfwpp rfwp prfwpp 1 1 - - ROL opr8a ROLA ROLX ROL oprx8,X ROL ,X ROL oprx8,SP Rotate Left through Carry ROR opr8a RORA RORX ROR oprx8,X ROR ,X ROR oprx8,SP Rotate Right through Carry C b7 b0 C b7 b0 MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 129 Chapter 7 Central Processor Unit (S08CPUV3) Operation Object Code Cycles Source Form Address Mode Table 7-2. Instruction Set Summary (Sheet 7 of 9) Cyc-by-Cyc Details Affect on CCR V11H INZC RSP Reset Stack Pointer (Low Byte) SPL $FF (High Byte Not Affected) INH 9C 1 p - 1 1 - - - - - RTI Return from Interrupt SP (SP) + $0001; Pull (CCR) SP (SP) + $0001; Pull (A) SP (SP) + $0001; Pull (X) SP (SP) + $0001; Pull (PCH) SP (SP) + $0001; Pull (PCL) INH 80 9 uuuuufppp 1 1 RTS Return from Subroutine SP SP + $0001; Pull (PCH) SP SP + $0001; Pull (PCL) INH 81 5 ufppp - 1 1 - - - - - Subtract with Carry A (A) - (M) - (C) IMM DIR EXT IX2 IX1 IX SP2 SP1 A2 B2 C2 D2 E2 F2 9E D2 9E E2 2 3 4 4 3 3 5 4 pp rpp prpp prpp rpp rfp pprpp prpp 1 1 - - SBC SBC SBC SBC SBC SBC SBC SBC #opr8i opr8a opr16a oprx16,X oprx8,X ,X oprx16,SP oprx8,SP ii dd hh ll ee ff ff ee ff ff SEC Set Carry Bit (C 1) INH 99 1 p - 1 1 - - - - 1 SEI Set Interrupt Mask Bit (I 1) INH 9B 1 p - 1 1 - 1 - - - Store Accumulator in Memory M (A) DIR EXT IX2 IX1 IX SP2 SP1 B7 C7 D7 E7 F7 9E D7 9E E7 wpp pwpp pwpp wpp wp ppwpp pwpp 0 1 1 - - - ee ff ff 3 4 4 3 2 5 4 35 dd 96 hh ll 9E FF ff 4 5 5 wwpp pwwpp pwwpp 0 1 1 - - - 2 fp... - 1 1 - 0 - - - 3 4 4 3 2 5 4 wpp pwpp pwpp wpp wp ppwpp pwpp 0 1 1 - - - STA STA STA STA STA STA STA opr8a opr16a oprx16,X oprx8,X ,X oprx16,SP oprx8,SP STHX opr8a STHX opr16a STHX oprx8,SP Store H:X (Index Reg.) (M:M + $0001) (H:X) DIR EXT SP1 STOP Enable Interrupts: Stop Processing Refer to MCU Documentation I bit 0; Stop Processing INH 8E Store X (Low 8 Bits of Index Register) in Memory M (X) DIR EXT IX2 IX1 IX SP2 SP1 BF CF DF EF FF 9E DF 9E EF STX STX STX STX STX STX STX opr8a opr16a oprx16,X oprx8,X ,X oprx16,SP oprx8,SP dd hh ll ee ff ff dd hh ll ee ff ff ee ff ff MC9S08DZ60 Series Data Sheet, Rev. 4 130 Freescale Semiconductor Chapter 7 Central Processor Unit (S08CPUV3) SUB SUB SUB SUB SUB SUB SUB SUB #opr8i opr8a opr16a oprx16,X oprx8,X ,X oprx16,SP oprx8,SP Operation Object Code IMM DIR EXT IX2 IX1 IX SP2 SP1 A0 B0 C0 D0 E0 F0 9E D0 9E E0 SWI Software Interrupt PC (PC) + $0001 Push (PCL); SP (SP) - $0001 Push (PCH); SP (SP) - $0001 Push (X); SP (SP) - $0001 Push (A); SP (SP) - $0001 Push (CCR); SP (SP) - $0001 I 1; PCH Interrupt Vector High Byte PCL Interrupt Vector Low Byte INH TAP Transfer Accumulator to CCR CCR (A) TAX TPA TST opr8a TSTA TSTX TST oprx8,X TST ,X TST oprx8,SP Cycles Source Form Address Mode Table 7-2. Instruction Set Summary (Sheet 8 of 9) Cyc-by-Cyc Details Affect on CCR V11H INZC 2 3 4 4 3 3 5 4 pp rpp prpp prpp rpp rfp pprpp prpp 1 1 - - 83 11 sssssvvfppp - 1 1 - 1 - - - INH 84 1 p 1 1 Transfer Accumulator to X (Index Register Low) X (A) INH 97 1 p - 1 1 - - - - - Transfer CCR to Accumulator A (CCR) INH 85 1 p - 1 1 - - - - - DIR INH INH IX1 IX SP1 3D dd 4D 5D 6D ff 7D 9E 6D ff 4 1 1 4 3 5 rfpp p p rfpp rfp prfpp 0 1 1 - - - Subtract A (A) - (M) Test for Negative or Zero (M) - $00 (A) - $00 (X) - $00 (M) - $00 (M) - $00 (M) - $00 ii dd hh ll ee ff ff ee ff ff TSX Transfer SP to Index Reg. H:X (SP) + $0001 INH 95 2 fp - 1 1 - - - - - TXA Transfer X (Index Reg. Low) to Accumulator A (X) INH 9F 1 p - 1 1 - - - - - MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 131 Chapter 7 Central Processor Unit (S08CPUV3) Operation Object Code Cycles Source Form Address Mode Table 7-2. Instruction Set Summary (Sheet 9 of 9) Affect on CCR Cyc-by-Cyc Details V11H INZC TXS Transfer Index Reg. to SP SP (H:X) - $0001 INH 94 2 fp - 1 1 - - - - - WAIT Enable Interrupts; Wait for Interrupt I bit 0; Halt CPU INH 8F 2+ fp... - 1 1 - 0 - - - Source Form: Everything in the source forms columns, except expressions in italic characters, is literal information which must appear in the assembly source file exactly as shown. The initial 3- to 5-letter mnemonic and the characters (#, ( ) and +) are always a literal characters. n Any label or expression that evaluates to a single integer in the range 0-7. opr8i Any label or expression that evaluates to an 8-bit immediate value. opr16i Any label or expression that evaluates to a 16-bit immediate value. opr8a Any label or expression that evaluates to an 8-bit direct-page address ($00xx). opr16a Any label or expression that evaluates to a 16-bit address. oprx8 Any label or expression that evaluates to an unsigned 8-bit value, used for indexed addressing. oprx16 Any label or expression that evaluates to a 16-bit value, used for indexed addressing. rel Any label or expression that refers to an address that is within -128 to +127 locations from the start of the next instruction. Operation Symbols: A Accumulator CCR Condition code register H Index register high byte M Memory location n Any bit opr Operand (one or two bytes) PC Program counter PCH Program counter high byte PCL Program counter low byte rel Relative program counter offset byte SP Stack pointer SPL Stack pointer low byte X Index register low byte & Logical AND | Logical OR Logical EXCLUSIVE OR () Contents of + Add - Subtract, Negation (two's complement) x Multiply / Divide # Immediate value Loaded with : Concatenated with Addressing Modes: DIR Direct addressing mode EXT Extended addressing mode IMM Immediate addressing mode INH Inherent addressing mode IX Indexed, no offset addressing mode IX1 Indexed, 8-bit offset addressing mode IX2 Indexed, 16-bit offset addressing mode IX+ Indexed, no offset, post increment addressing mode IX1+ Indexed, 8-bit offset, post increment addressing mode REL Relative addressing mode SP1 Stack pointer, 8-bit offset addressing mode SP2 Stack pointer 16-bit offset addressing mode CCR Bits: V Overflow bit H Half-carry bit I Interrupt mask N Negative bit Z Zero bit C Carry/borrow bit CCR Effects: Set or cleared - Not affected U Undefined Cycle-by-Cycle Codes: f Free cycle. This indicates a cycle where the CPU does not require use of the system buses. An f cycle is always one cycle of the system bus clock and is always a read cycle. p Program fetch; read from next consecutive location in program memory r Read 8-bit operand s Push (write) one byte onto stack u Pop (read) one byte from stack v Read vector from $FFxx (high byte first) w Write 8-bit operand MC9S08DZ60 Series Data Sheet, Rev. 4 132 Freescale Semiconductor Chapter 7 Central Processor Unit (S08CPUV3) Table 7-3. Opcode Map (Sheet 1 of 2) Bit-Manipulation 00 5 10 5 BRSET0 3 01 BRCLR1 3 04 BRSET2 3 05 3 07 BRSET4 3 09 BRSET5 3 0B BRSET6 3 0D BRCLR6 3 0E BRSET7 3 0F BRCLR7 3 INH IMM DIR EXT DD IX+D INC DIR 2 5 2F TST REL 2 3 3E CPHX REL 3 3 3F BIH CLR DIR 1 ASR INH 2 1 68 INH 1 Relative Indexed, No Offset Indexed, 8-Bit Offset Indexed, 16-Bit Offset IMM to DIR DIR to IX+ ROL DEC ROL DEC DBNZ INH 3 1 6C DBNZ INC INH 2 1 6D INC IX1 1 4 7D TST INH 2 5 6E MOV CLRX IX1 1 CLR ADD INH 2 1 INH 1 2 BD BSR Page 2 WAIT 5 1 JSR REL 2 2 BE LDX 2 AF TXA INH 2 AIX LDX DIR 3 3 CF STX IMM 2 EXT 3 4 DF STX DIR 3 EXT 3 Opcode in Hexadecimal F0 EOR ADC IX2 2 IX 2 STA IX 3 EOR IX 3 ADC IX1 1 3 FA ORA IX 3 ORA IX1 1 3 FB ADD JSR LDX IX1 1 3 FF IX 5 JSR IX1 1 3 FE IX1 1 IX 3 JMP IX1 1 5 FD STX IX 3 ADD IX1 1 3 FC JMP IX2 2 4 EF STX IX 3 LDA IX1 1 3 F9 IX2 2 4 EE LDX BIT IX1 1 3 F8 IX2 2 6 ED JSR EXT 3 4 DE IX 3 STA IX2 2 4 EC JMP EXT 3 6 DD JSR DIR 3 3 CE LDX IMM 2 2 BF Stack Pointer, 8-Bit Offset Stack Pointer, 16-Bit Offset Indexed, No Offset with Post Increment Indexed, 1-Byte Offset with Post Increment JMP DIR 3 5 CD AND IX1 1 3 F7 IX2 2 4 EB ADD EXT 3 4 DC IX 3 LDA IX2 2 4 EA ORA EXT 3 4 DB ADD JMP INH 2 AE INH 2+ 9F ORA CPX IX1 1 3 F6 IX2 2 4 E9 ADC EXT 3 4 DA IX 3 BIT IX2 2 4 E8 EOR IX 3 SBC IX1 1 3 F5 STA ADC DIR 3 3 CC AND IX2 2 4 E7 EXT 3 4 D9 CMP IX1 1 3 F4 IX2 2 4 E6 EXT 3 4 D8 EOR DIR 3 3 CB ADD IMM 2 BC INH 1 AD NOP IX 1 IMM 2 2 BB CPX LDA STA IX 3 IX1 1 3 F3 IX2 2 4 E5 EXT 3 4 D7 DIR 3 3 CA ORA RSP 1 2+ 9E STOP ADC SBC BIT LDA DIR 3 3 C9 IMM 2 2 BA ORA SEI INH 1 9D IX 5 8E MOV ADC INH 2 1 AB INH 1 1 9C CLRH IX 1 3 IMD 2 IX+D 1 5 7F 4 8F CLR INH 2 INH 1 2 9B EOR AND 3 SUB IX1 1 3 F2 IX2 2 4 E4 EXT 3 4 D6 DIR 3 3 C8 IMM 2 2 B9 INH 2 1 AA CLI TST IX1 1 4 7E MOV SEC INH 1 3 9A PSHH IX 1 4 8C EOR CPX BIT STA CMP IX2 2 4 E3 EXT 3 4 D5 DIR 3 3 C7 IMM 2 2 B8 INH 2 1 A9 PULH IX 1 6 8B IX1 2 5 7C CLC INH 1 2 99 AND LDA AIS INH 2 1 A8 SBC F0 IX1 1 3 F1 IX2 2 4 E2 EXT 3 4 D4 DIR 3 3 C6 IMM 2 2 B7 TAX CPX BIT LDA CMP EXT 3 4 D3 DIR 3 3 C5 IMM 2 2 B6 EXT 2 1 A7 INH 1 3 98 PSHX IX 1 4 8A IX1 1 7 7B INH 3 2 97 PULX IX 1 4 89 IX1 1 5 7A INH 2 4 6B IX1+ LSL STHX PSHA IX 1 4 88 IX1 1 5 79 INH 2 1 6A SP1 SP2 IX+ ASR LSL INH 2 1 69 PULA IX 1 4 87 IX1 1 5 78 DD 2 DIX+ 3 1 5F 1 6F CLRA ROR AND BIT INH 2 5 A6 SBC 3 SUB IX2 2 4 E1 EXT 3 4 D2 DIR 3 3 C4 IMM 2 2 B5 TSX INH 1 3 96 CPX AND CMP E0 SUB EXT 3 4 D1 DIR 3 3 C3 IMM 2 2 B4 INH 2 2 A5 TPA DIR 1 4 86 IX1 1 5 77 TSTX INH 1 5 5E MOV EXT 3 5 4F REL 2 REL IX IX1 IX2 IMD DIX+ TSTA DIR 1 6 4E INH 2 1 67 INCX INH 1 1 5D CPHX TXS INH 1 1 95 SBC CPX SUB DIR 3 3 C2 IMM 2 2 B3 REL 2 2 A4 TAP IX 1 5 85 IMM 2 5 76 ROR DBNZX INH 2 1 5C INCA DIR 1 4 4D CPHX DIR 3 1 66 DECX INH 1 4 5B DBNZA DIR 2 5 4C REL 2 3 3D BIL DECA DIR 1 7 4B DBNZ BMS DIR 2 5 2E Inherent Immediate Direct Extended DIR to DIR IX+ to DIR DEC LSR CMP SBC BLE Register/Memory C0 4 D0 4 DIR 3 3 C1 IMM 2 2 B2 REL 2 3 A3 INH 2 1 94 3 SUB CMP BGT SWI B0 IMM 2 2 B1 REL 2 3 A2 INH 2 11 93 IX 1 4 84 2 SUB BLT INH 2 5+ 92 BGND COM A0 REL 2 3 A1 RTS INH 1 4 83 IX1 1 3 75 ROLX INH 1 1 5A DAA 3 BGE INH 2 6 91 IX+ 1 1 82 LSR LSLX INH 1 1 59 CBEQ IX1 1 5 74 INH 2 4 65 ASRX INH 1 1 58 ROLA DIR 1 5 4A BMC DIR 2 5 2D DIR 2 ROL REL 3 3 3C INH 1 1 57 LSLA DIR 1 5 49 REL 2 3 3B BMI DIR 2 5 2C BCLR7 DIR 2 LSL COM RTI IX 1 5 81 INH 1 5 73 INH 2 1 64 RORX ASRA DIR 1 5 48 REL 2 3 3A DIR 2 5 2B BSET7 DIR 2 5 1F ASR BHCS BPL RORA DIR 1 5 47 REL 2 3 39 DIR 2 5 2A BCLR6 DIR 2 5 1E ROR INH 1 1 63 Control 9 90 80 NEG NSA LDHX IMM 2 1 56 4 IX1+ 2 1 72 LSRX INH 1 3 55 LDHX DIR 3 5 46 BHCC DIR 2 5 29 BSET6 DIR 2 5 1D STHX CBEQ COMX INH 1 1 54 LSRA DIR 1 4 45 REL 2 3 38 BCLR5 DIR 2 5 1C LSR BEQ INH 1 1 53 70 IX1 1 5 71 IMM 3 6 62 DIV COMA DIR 1 5 44 REL 2 3 37 BSET5 DIR 2 5 1B BRCLR5 3 0C BNE DIR 2 5 28 BCLR4 DIR 2 5 1A COM REL 2 3 36 DIR 2 5 27 BSET4 DIR 2 5 19 BRCLR4 3 0A BCS MUL 5 NEG INH 2 4 61 CBEQX IMM 3 5 52 EXT 1 5 43 REL 2 3 35 DIR 2 5 26 CBEQA LDHX NEGX INH 1 4 51 DIR 3 5 42 BCC BCLR3 DIR 2 5 18 CBEQ REL 2 3 34 DIR 2 5 25 BSET3 DIR 2 5 17 BRCLR3 3 08 BLS NEGA DIR 1 5 41 REL 3 3 33 DIR 2 5 24 BCLR2 DIR 2 5 16 BRSET3 DIR 2 5 23 Read-Modify-Write 1 50 1 60 40 NEG REL 3 3 32 BHI BSET2 DIR 2 5 15 BRCLR2 3 06 BRN DIR 2 5 22 BCLR1 DIR 2 5 14 5 REL 2 3 31 BSET1 DIR 2 5 13 30 BRA DIR 2 5 21 BCLR0 DIR 2 5 12 BRSET1 3 03 BSET0 DIR 2 5 11 BRCLR0 3 02 Branch 20 3 IX 3 LDX IX 2 STX IX 3 HCS08 Cycles Instruction Mnemonic IX Addressing Mode SUB Number of Bytes 1 MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 133 Chapter 7 Central Processor Unit (S08CPUV3) Table 7-3. Opcode Map (Sheet 2 of 2) Bit-Manipulation Branch Read-Modify-Write 9E60 Control Register/Memory 9ED0 5 6 NEG CMP SP1 CMP 4 SP2 3 SP1 9ED2 5 9EE2 4 SBC 9E63 SBC 4 SP2 3 SP1 9ED3 5 9EE3 4 9EF3 6 COM CPX 3 SP1 9E64 6 CPX AND SP1 SP1 AND 4 SP2 3 SP1 9ED5 5 9EE5 4 BIT BIT 6 4 SP2 3 SP1 9ED6 5 9EE6 4 3 SP1 9E67 6 4 SP2 3 SP1 9ED7 5 9EE7 4 9E66 6 CPHX 4 SP2 3 SP1 3 9ED4 5 9EE4 4 LSR 3 4 SUB 4 SP2 3 SP1 9ED1 5 9EE1 4 CBEQ 4 9EE0 SUB 3 SP1 9E61 6 ROR LDA ASR LDA STA 3 SP1 9E68 6 STA 4 SP2 3 SP1 9ED8 5 9EE8 4 LSL EOR 3 SP1 9E69 6 EOR 4 SP2 3 SP1 9ED9 5 9EE9 4 ROL ADC 3 SP1 9E6A 6 ADC 4 SP2 3 SP1 9EDA 5 9EEA 4 DEC ORA 3 SP1 9E6B 8 ORA 4 SP2 3 SP1 9EDB 5 9EEB 4 DBNZ ADD 4 SP1 9E6C 6 4 ADD SP2 3 SP1 INC 3 SP1 9E6D 5 TST 3 SP1 9EAE 5 9EBE LDHX 2 9E6F IX 4 6 9ECE LDHX 5 9EDE LDHX IX2 3 6 CLR 3 INH IMM DIR EXT DD IX+D Inherent Immediate Direct Extended DIR to DIR IX+ to DIR REL IX IX1 IX2 IMD DIX+ Relative Indexed, No Offset Indexed, 8-Bit Offset Indexed, 16-Bit Offset IMM to DIR DIR to IX+ SP1 SP2 IX+ IX1+ Note: All Sheet 2 Opcodes are Preceded by the Page 2 Prebyte (9E) 5 9EEE LDX 4 9EFE LDX 5 LDHX IX1 4 SP2 3 SP1 3 SP1 9EDF 5 9EEF 4 9EFF 5 STX SP1 4 SP2 3 STX SP1 3 STHX SP1 Stack Pointer, 8-Bit Offset Stack Pointer, 16-Bit Offset Indexed, No Offset with Post Increment Indexed, 1-Byte Offset with Post Increment Prebyte (9E) and Opcode in Hexadecimal 9E60 6 HCS08 Cycles Instruction Mnemonic SP1 Addressing Mode NEG Number of Bytes 3 MC9S08DZ60 Series Data Sheet, Rev. 4 134 Freescale Semiconductor Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) 8.1 Introduction The multi-purpose clock generator (MCG) module provides several clock source choices for the MCU. The module contains a frequency-locked loop (FLL) and a phase-locked loop (PLL) that are controllable by either an internal or an external reference clock. The module can select either of the FLL or PLL clocks, or either of the internal or external reference clocks as a source for the MCU system clock. Whichever clock source is chosen, it is passed through a reduced bus divider which allows a lower output clock frequency to be derived. The MCG also controls an external oscillator (XOSC) for the use of a crystal or resonator as the external reference clock. All devices in the MC9S08DZ60 Series feature the MCG module. NOTE Refer to Section 1.3, "System Clock Distribution," for detailed view of the distribution clock sources throughout the chip. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 135 PORT A PTA7/PIA7/ADP7/IRQ PTA6/PIA6/ADP6 PTA5/PIA5/ADP5 PTA4/PIA4/ADP4 PTA3/PIA3/ADP3/ACMP1O PTA2/PIA2/ADP2/ACMP1PTA1/PIA1/ADP1/ACMP1+ PTA0/PIA0/ADP0/MCLK PORT B PTB7/PIB7/ADP15 PTB6/PIB6/ADP14 PTB5/PIB5/ADP13 PTB4/PIB4/ADP12 PTB3/PIB3/ADP11 PTB2/PIB2/ADP10 PTB1/PIB1/ADP9 PTB0/PIB0/ADP8 PORT C PTC7/ADP23 PTC6/ADP22 PTC5/ADP21 PTC4/ADP20 PTC3/ADP19 PTC2/ADP18 PTC1/ADP17 PTC0/ADP16 PORT D PTD7/PID7/TPM1CH5 PTD6/PID6/TPM1CH4 PTD5/PID5/TPM1CH3 PTD4/PID4/TPM1CH2 PTD3/PID3/TPM1CH1 PTD2/PID2/TPM1CH0 PTD1/PID1/TPM2CH1 PTD0/PID0/TPM2CH0 PORT E PTE7/RxD2/RXCAN PTE6/TxD2/TXCAN PTE5/SDA/MISO PTE4/SCL/MOSI PTE3/SPSCK PTE2/SS PTE1/RxD1 PTE0/TxD1 PORT F PTF7 PTF6/ACMP2O PTF5/ACMP2PTF4/ACMP2+ PTF3/TPM2CLK/SDA PTF2/TPM1CLK/SCL PTF1/RxD2 PTF0/TxD2 PORT G Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) PTG5 PTG4 PTG3 PTG2 PTG1/XTAL PTG0/EXTAL HCS08 CORE CPU BKGD/MS BDC ANALOG COMPARATOR (ACMP1) BKP ACMP1O ACMP1ACMP1+ HCS08 SYSTEM CONTROL RESETS AND INTERRUPTS MODES OF OPERATION POWER MANAGEMENT COP LVD INT IRQ ADP7-ADP0 24-CHANNEL,12-BIT ANALOG-TO-DIGITAL CONVERTER (ADC) VREFH VREFL VDDA VSSA USER FLASH MC9S0DZ60 = 60K MC9S0DZ48 = 48K MC9S0DZ32 = 32K MC9S0DZ16 = 16K USER EEPROM MC9S0DZ60 = 2K TPM1CH5 TPM1CH0 6 TPM1CLK 2-CHANNEL TIMER/PWM MODULE (TPM2) TPM2CH1, TPM2CH0 TPM2CLK CONTROLLER AREA NETWORK (MSCAN) SERIAL PERIPHERAL INTERFACE MODULE (SPI) DEBUG MODULE (DBG) SERIAL COMMUNICATIONS INTERFACE (SCI1) VOLTAGE REGULATOR ADP15-ADP8 ADP23-ADP16 6-CHANNEL TIMER/PWM MODULE (TPM1) USER RAM MC9S0DZ60 = 4K REAL-TIME COUNTER (RTC) VDD VDD VSS VSS 8 IRQ RESET ANALOG COMPARATOR (ACMP2) IIC MODULE (IIC) SERIAL COMMUNICATIONS INTERFACE (SCI2) RxCAN TxCAN MISO MOSI SPSCK SS RxD1 TxD1 ACMP2O ACMP2ACMP2+ SDA SCL RxD2 TxD2 MULTI-PURPOSE CLOCK GENERATOR (MCG) XTAL EXTAL OSCILLATOR (XOSC) - VREFH/VREFL internally connected to VDDA/VSSA in 48-pin and 32-pin packages - VDD and VSS pins are each internally connected to two pads in 32-pin package - Pin not connected in 48-pin and 32-pin packages - Pin not connected in 32-pin package Figure 8-1. MC9S08DZ60 Block Diagram MC9S08DZ60 Series Data Sheet, Rev. 4 136 Freescale Semiconductor Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) 8.1.1 Features Key features of the MCG module are: * Frequency-locked loop (FLL) -- 0.2% resolution using internal 32-kHz reference -- 2% deviation over voltage and temperature using internal 32-kHz reference -- Internal or external reference can be used to control the FLL * Phase-locked loop (PLL) -- Voltage-controlled oscillator (VCO) -- Modulo VCO frequency divider -- Phase/Frequency detector -- Integrated loop filter -- Lock detector with interrupt capability * Internal reference clock -- Nine trim bits for accuracy -- Can be selected as the clock source for the MCU * External reference clock -- Control for external oscillator -- Clock monitor with reset capability -- Can be selected as the clock source for the MCU * Reference divider is provided * Clock source selected can be divided down by 1, 2, 4, or 8 * BDC clock (MCGLCLK) is provided as a constant divide by 2 of the DCO output whether in an FLL or PLL mode. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 137 Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) External Oscillator (XOSC) RANGE EREFS ERCLKEN MCGERCLK HGO EREFSTEN IRCLKEN MCGIRCLK CME IREFSTEN CLKS Clock Monitor LOC BDIV / 2n Internal Reference Clock OSCINIT 9 IREFS MCGOUT n=0-3 LP DCO DCOOUT TRIM PLLS / 2n RDIV_CLK Lock Detector Filter n=0-7 FLL RDIV LOLS LOCK MCGFFCLK MCGFFCLKVALID MCGLCLK LP VCOOUT Phase Detector Charge Pump VDIV Internal Filter /2 VCO PLL /(4,8,12,...,40) Multi-purpose Clock Generator (MCG) Figure 8-2. Multi-Purpose Clock Generator (MCG) Block Diagram MC9S08DZ60 Series Data Sheet, Rev. 4 138 Freescale Semiconductor Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) 8.1.2 Modes of Operation There are nine modes of operation for the MCG: * FLL Engaged Internal (FEI) * FLL Engaged External (FEE) * FLL Bypassed Internal (FBI) * FLL Bypassed External (FBE) * PLL Engaged External (PEE) * PLL Bypassed External (PBE) * Bypassed Low Power Internal (BLPI) * Bypassed Low Power External (BLPE) * Stop For details see Section 8.4.1, "Operational Modes. 8.2 External Signal Description There are no MCG signals that connect off chip. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 139 Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) 8.3 Register Definition 8.3.1 MCG Control Register 1 (MCGC1) 7 6 5 4 3 2 1 0 IREFS IRCLKEN IREFSTEN 1 0 0 R CLKS RDIV W Reset: 0 0 0 0 0 Figure 8-3. MCG Control Register 1 (MCGC1) Table 8-1. MCG Control Register 1 Field Descriptions Field Description 7:6 CLKS Clock Source Select -- Selects the system clock source. 00 Encoding 0 -- Output of FLL or PLL is selected. 01 Encoding 1 -- Internal reference clock is selected. 10 Encoding 2 -- External reference clock is selected. 11 Encoding 3 -- Reserved, defaults to 00. 5:3 RDIV Reference Divider -- Selects the amount to divide down the reference clock selected by the IREFS bit. If the FLL is selected, the resulting frequency must be in the range 31.25 kHz to 39.0625 kHz. If the PLL is selected, the resulting frequency must be in the range 1 MHz to 2 MHz. 000 Encoding 0 -- Divides reference clock by 1 (reset default) 001 Encoding 1 -- Divides reference clock by 2 010 Encoding 2 -- Divides reference clock by 4 011 Encoding 3 -- Divides reference clock by 8 100 Encoding 4 -- Divides reference clock by 16 101 Encoding 5 -- Divides reference clock by 32 110 Encoding 6 -- Divides reference clock by 64 111 Encoding 7 -- Divides reference clock by 128 2 IREFS Internal Reference Select -- Selects the reference clock source. 1 Internal reference clock selected 0 External reference clock selected 1 IRCLKEN 0 IREFSTEN Internal Reference Clock Enable -- Enables the internal reference clock for use as MCGIRCLK. 1 MCGIRCLK active 0 MCGIRCLK inactive Internal Reference Stop Enable -- Controls whether or not the internal reference clock remains enabled when the MCG enters stop mode. 1 Internal reference clock stays enabled in stop if IRCLKEN is set or if MCG is in FEI, FBI, or BLPI mode before entering stop 0 Internal reference clock is disabled in stop MC9S08DZ60 Series Data Sheet, Rev. 4 140 Freescale Semiconductor Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) 8.3.2 MCG Control Register 2 (MCGC2) 7 6 5 4 3 2 RANGE HGO LP EREFS 0 0 0 0 1 0 R BDIV ERCLKEN EREFSTEN W Reset: 0 1 0 0 Figure 8-4. MCG Control Register 2 (MCGC2) Table 8-2. MCG Control Register 2 Field Descriptions Field Description 7:6 BDIV Bus Frequency Divider -- Selects the amount to divide down the clock source selected by the CLKS bits in the MCGC1 register. This controls the bus frequency. 00 Encoding 0 -- Divides selected clock by 1 01 Encoding 1 -- Divides selected clock by 2 (reset default) 10 Encoding 2 -- Divides selected clock by 4 11 Encoding 3 -- Divides selected clock by 8 5 RANGE Frequency Range Select -- Selects the frequency range for the external oscillator or external clock source. 1 High frequency range selected for the external oscillator of 1 MHz to 16 MHz (1 MHz to 40 MHz for external clock source) 0 Low frequency range selected for the external oscillator of 32 kHz to 100 kHz (32 kHz to 1 MHz for external clock source) 4 HGO 3 LP 2 EREFS 1 ERCLKEN High Gain Oscillator Select -- Controls the external oscillator mode of operation. 1 Configure external oscillator for high gain operation 0 Configure external oscillator for low power operation Low Power Select -- Controls whether the FLL (or PLL) is disabled in bypassed modes. 1 FLL (or PLL) is disabled in bypass modes (lower power). 0 FLL (or PLL) is not disabled in bypass modes. External Reference Select -- Selects the source for the external reference clock. 1 Oscillator requested 0 External Clock Source requested External Reference Enable -- Enables the external reference clock for use as MCGERCLK. 1 MCGERCLK active 0 MCGERCLK inactive 0 External Reference Stop Enable -- Controls whether or not the external reference clock remains enabled when EREFSTEN the MCG enters stop mode. 1 External reference clock stays enabled in stop if ERCLKEN is set or if MCG is in FEE, FBE, PEE, PBE, or BLPE mode before entering stop 0 External reference clock is disabled in stop MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 141 Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) 8.3.3 MCG Trim Register (MCGTRM) 7 6 5 4 3 2 1 0 R TRIM W POR: 1 0 0 0 0 0 0 0 Reset: U U U U U U U U Figure 8-5. MCG Trim Register (MCGTRM) Table 8-3. MCG Trim Register Field Descriptions Field Description 7:0 TRIM MCG Trim Setting -- Controls the internal reference clock frequency by controlling the internal reference clock period. The TRIM bits are binary weighted (i.e., bit 1 will adjust twice as much as bit 0). Increasing the binary value in TRIM will increase the period, and decreasing the value will decrease the period. An additional fine trim bit is available in MCGSC as the FTRIM bit. If a TRIM[7:0] value stored in nonvolatile memory is to be used, it's the user's responsibility to copy that value from the nonvolatile memory location to this register. MC9S08DZ60 Series Data Sheet, Rev. 4 142 Freescale Semiconductor Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) 8.3.4 MCG Status and Control Register (MCGSC) R 7 6 5 4 3 LOLS LOCK PLLST IREFST 2 CLKST 1 0 OSCINIT FTRIM W POR: Reset: 0 0 0 0 0 0 1 1 0 0 0 0 0 0 0 U Figure 8-6. MCG Status and Control Register (MCGSC) Table 8-4. MCG Status and Control Register Field Descriptions Field Description 7 LOLS Loss of Lock Status -- This bit is a sticky indication of lock status for the FLL or PLL. LOLS is set when lock detection is enabled and after acquiring lock, the FLL or PLL output frequency has fallen outside the lock exit frequency tolerance, Dunl. LOLIE determines whether an interrupt request is made when set. LOLS is cleared by reset or by writing a logic 1 to LOLS when LOLS is set. Writing a logic 0 to LOLS has no effect. 0 FLL or PLL has not lost lock since LOLS was last cleared. 1 FLL or PLL has lost lock since LOLS was last cleared. 6 LOCK Lock Status -- Indicates whether the FLL or PLL has acquired lock. Lock detection is disabled when both the FLL and PLL are disabled. If the lock status bit is set then changing the value of any of the following bits IREFS, PLLS, RDIV[2:0], TRIM[7:0] (if in FEI or FBI modes), or VDIV[3:0] (if in PBE or PEE modes), will cause the lock status bit to clear and stay cleared until the FLL or PLL has reacquired lock. Stop mode entry will also cause the lock status bit to clear and stay cleared until the FLL or PLL has reacquired lock. Entry into BLPI or BLPE mode will also cause the lock status bit to clear and stay cleared until the MCG has exited these modes and the FLL or PLL has reacquired lock. 0 FLL or PLL is currently unlocked. 1 FLL or PLL is currently locked. 5 PLLST PLL Select Status -- The PLLST bit indicates the current source for the PLLS clock. The PLLST bit does not update immediately after a write to the PLLS bit due to internal synchronization between clock domains. 0 Source of PLLS clock is FLL clock. 1 Source of PLLS clock is PLL clock. 4 IREFST Internal Reference Status -- The IREFST bit indicates the current source for the reference clock. The IREFST bit does not update immediately after a write to the IREFS bit due to internal synchronization between clock domains. 0 Source of reference clock is external reference clock (oscillator or external clock source as determined by the EREFS bit in the MCGC2 register). 1 Source of reference clock is internal reference clock. 3:2 CLKST Clock Mode Status -- The CLKST bits indicate the current clock mode. The CLKST bits do not update immediately after a write to the CLKS bits due to internal synchronization between clock domains. 00 Encoding 0 -- Output of FLL is selected. 01 Encoding 1 -- Internal reference clock is selected. 10 Encoding 2 -- External reference clock is selected. 11 Encoding 3 -- Output of PLL is selected. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 143 Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) Table 8-4. MCG Status and Control Register Field Descriptions (continued) Field Description 1 OSCINIT OSC Initialization -- If the external reference clock is selected by ERCLKEN or by the MCG being in FEE, FBE, PEE, PBE, or BLPE mode, and if EREFS is set, then this bit is set after the initialization cycles of the external oscillator clock have completed. This bit is only cleared when either EREFS is cleared or when the MCG is in either FEI, FBI, or BLPI mode and ERCLKEN is cleared. 0 FTRIM MCG Fine Trim -- Controls the smallest adjustment of the internal reference clock frequency. Setting FTRIM will increase the period and clearing FTRIM will decrease the period by the smallest amount possible. If an FTRIM value stored in nonvolatile memory is to be used, it's the user's responsibility to copy that value from the nonvolatile memory location to this register's FTRIM bit. 8.3.5 MCG Control Register 3 (MCGC3) 7 6 5 LOLIE PLLS CME 0 0 0 R 4 3 2 1 0 0 1 0 VDIV W Reset: 0 0 0 Figure 8-7. MCG PLL Register (MCGPLL) Table 8-5. MCG PLL Register Field Descriptions Field Description 7 LOLIE Loss of Lock Interrupt Enable -- Determines if an interrupt request is made following a loss of lock indication. The LOLIE bit only has an effect when LOLS is set. 0 No request on loss of lock. 1 Generate an interrupt request on loss of lock. 6 PLLS PLL Select -- Controls whether the PLL or FLL is selected. If the PLLS bit is clear, the PLL is disabled in all modes. If the PLLS is set, the FLL is disabled in all modes. 1 PLL is selected 0 FLL is selected MC9S08DZ60 Series Data Sheet, Rev. 4 144 Freescale Semiconductor Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) Table 8-5. MCG PLL Register Field Descriptions (continued) Field Description 5 CME Clock Monitor Enable -- Determines if a reset request is made following a loss of external clock indication. The CME bit should only be set to a logic 1 when either the MCG is in an operational mode that uses the external clock (FEE, FBE, PEE, PBE, or BLPE) or the external reference is enabled (ERCLKEN=1 in the MCGC2 register). Whenever the CME bit is set to a logic 1, the value of the RANGE bit in the MCGC2 register should not be changed. 0 Clock monitor is disabled. 1 Generate a reset request on loss of external clock. 3:0 VDIV VCO Divider -- Selects the amount to divide down the VCO output of PLL. The VDIV bits establish the multiplication factor (M) applied to the reference clock frequency. 0000 Encoding 0 -- Reserved. 0001 Encoding 1 -- Multiply by 4. 0010 Encoding 2 -- Multiply by 8. 0011 Encoding 3 -- Multiply by 12. 0100 Encoding 4 -- Multiply by 16. 0101 Encoding 5 -- Multiply by 20. 0110 Encoding 6 -- Multiply by 24. 0111 Encoding 7 -- Multiply by 28. 1000 Encoding 8 -- Multiply by 32. 1001 Encoding 9 -- Multiply by 36. 1010 Encoding 10 -- Multiply by 40. 1011 Encoding 11 -- Reserved (default to M=40). 11xx Encoding 12-15 -- Reserved (default to M=40). MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 145 Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) 8.4 Functional Description 8.4.1 Operational Modes IREFS=1 CLKS=00 PLLS=0 IREFS=1 CLKS=01 PLLS=0 BDM Enabled or LP=0 IREFS=1 CLKS=01 PLLS=0 BDM Disabled and LP=1 FLL Engaged Internal (FEI) FLL Engaged External (FEE) FLL Bypassed Internal (FBI) FLL Bypassed External (FBE) IREFS=0 CLKS=10 PLLS=0 BDM Enabled or LP=0 Bypassed IREFS=0 Low Power CLKS=10 External (BLPE) BDM Disabled and LP=1 Bypassed Low Power Internal (BLPI) Entered from any state when MCU enters stop IREFS=0 CLKS=00 PLLS=0 Stop PLL Bypassed External (PBE) IREFS=0 CLKS=10 PLLS=1 BDM Enabled or LP=0 PLL Engaged External (PEE) IREFS=0 CLKS=00 PLLS=1 Returns to state that was active before MCU entered stop, unless RESET occurs while in stop. Figure 8-8. Clock Switching Modes MC9S08DZ60 Series Data Sheet, Rev. 4 146 Freescale Semiconductor Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) The nine states of the MCG are shown as a state diagram and are described below. The arrows indicate the allowed movements between the states. 8.4.1.1 FLL Engaged Internal (FEI) FLL engaged internal (FEI) is the default mode of operation and is entered when all the following conditions occur: * CLKS bits are written to 00 * IREFS bit is written to 1 * PLLS bit is written to 0 * RDIV bits are written to 000. Since the internal reference clock frequency should already be in the range of 31.25 kHz to 39.0625 kHz after it is trimmed, no further frequency divide is necessary. In FLL engaged internal mode, the MCGOUT clock is derived from the FLL clock, which is controlled by the internal reference clock. The FLL clock frequency locks to 1024 times the reference frequency, as selected by the RDIV bits. The MCGLCLK is derived from the FLL and the PLL is disabled in a low power state. 8.4.1.2 FLL Engaged External (FEE) The FLL engaged external (FEE) mode is entered when all the following conditions occur: * * * * CLKS bits are written to 00 IREFS bit is written to 0 PLLS bit is written to 0 RDIV bits are written to divide reference clock to be within the range of 31.25 kHz to 39.0625 kHz In FLL engaged external mode, the MCGOUT clock is derived from the FLL clock which is controlled by the external reference clock. The external reference clock which is enabled can be an external crystal/resonator or it can be another external clock source.The FLL clock frequency locks to 1024 times the reference frequency, as selected by the RDIV bits. The MCGLCLK is derived from the FLL and the PLL is disabled in a low power state. 8.4.1.3 FLL Bypassed Internal (FBI) In FLL bypassed internal (FBI) mode, the MCGOUT clock is derived from the internal reference clock and the FLL is operational but its output clock is not used. This mode is useful to allow the FLL to acquire its target frequency while the MCGOUT clock is driven from the internal reference clock. The FLL bypassed internal mode is entered when all the following conditions occur: * CLKS bits are written to 01 * IREFS bit is written to 1 * PLLS bit is written to 0 * RDIV bits are written to 000. Since the internal reference clock frequency should already be in the range of 31.25 kHz to 39.0625 kHz after it is trimmed, no further frequency divide is necessary. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 147 Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) * LP bit is written to 0 In FLL bypassed internal mode, the MCGOUT clock is derived from the internal reference clock. The FLL clock is controlled by the internal reference clock, and the FLL clock frequency locks to 1024 times the reference frequency, as selected by the RDIV bits. The MCGLCLK is derived from the FLL and the PLL is disabled in a low power state. 8.4.1.4 FLL Bypassed External (FBE) In FLL bypassed external (FBE) mode, the MCGOUT clock is derived from the external reference clock and the FLL is operational but its output clock is not used. This mode is useful to allow the FLL to acquire its target frequency while the MCGOUT clock is driven from the external reference clock. The FLL bypassed external mode is entered when all the following conditions occur: * CLKS bits are written to 10 * IREFS bit is written to 0 * PLLS bit is written to 0 * RDIV bits are written to divide reference clock to be within the range of 31.25 kHz to 39.0625 kHz * LP bit is written to 0 In FLL bypassed external mode, the MCGOUT clock is derived from the external reference clock. The external reference clock which is enabled can be an external crystal/resonator or it can be another external clock source.The FLL clock is controlled by the external reference clock, and the FLL clock frequency locks to 1024 times the reference frequency, as selected by the RDIV bits. The MCGLCLK is derived from the FLL and the PLL is disabled in a low power state. NOTE It is possible to briefly operate in FBE mode with an FLL reference clock frequency that is greater than the specified maximum frequency. This can be necessary in applications that operate in PEE mode using an external crystal with a frequency above 5 MHz. Please see 8.5.2.4, "Example # 4: Moving from FEI to PEE Mode: External Crystal = 8 MHz, Bus Frequency = 8 MHz for a detailed example. 8.4.1.5 PLL Engaged External (PEE) The PLL engaged external (PEE) mode is entered when all the following conditions occur: * * * * CLKS bits are written to 00 IREFS bit is written to 0 PLLS bit is written to 1 RDIV bits are written to divide reference clock to be within the range of 1 MHz to 2 MHz In PLL engaged external mode, the MCGOUT clock is derived from the PLL clock which is controlled by the external reference clock. The external reference clock which is enabled can be an external crystal/resonator or it can be another external clock source The PLL clock frequency locks to a MC9S08DZ60 Series Data Sheet, Rev. 4 148 Freescale Semiconductor Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) multiplication factor, as selected by the VDIV bits, times the reference frequency, as selected by the RDIV bits. If BDM is enabled then the MCGLCLK is derived from the DCO (open-loop mode) divided by two. If BDM is not enabled then the FLL is disabled in a low power state. 8.4.1.6 PLL Bypassed External (PBE) In PLL bypassed external (PBE) mode, the MCGOUT clock is derived from the external reference clock and the PLL is operational but its output clock is not used. This mode is useful to allow the PLL to acquire its target frequency while the MCGOUT clock is driven from the external reference clock. The PLL bypassed external mode is entered when all the following conditions occur: * CLKS bits are written to 10 * IREFS bit is written to 0 * PLLS bit is written to 1 * RDIV bits are written to divide reference clock to be within the range of 1 MHz to 2 MHz * LP bit is written to 0 In PLL bypassed external mode, the MCGOUT clock is derived from the external reference clock. The external reference clock which is enabled can be an external crystal/resonator or it can be another external clock source. The PLL clock frequency locks to a multiplication factor, as selected by the VDIV bits, times the reference frequency, as selected by the RDIV bits. If BDM is enabled then the MCGLCLK is derived from the DCO (open-loop mode) divided by two. If BDM is not enabled then the FLL is disabled in a low power state. 8.4.1.7 Bypassed Low Power Internal (BLPI) The bypassed low power internal (BLPI) mode is entered when all the following conditions occur: * CLKS bits are written to 01 * IREFS bit is written to 1 * PLLS bit is written to 0 * LP bit is written to 1 * BDM mode is not active In bypassed low power internal mode, the MCGOUT clock is derived from the internal reference clock. The PLL and the FLL are disabled at all times in BLPI mode and the MCGLCLK will not be available for BDC communications If the BDM becomes active the mode will switch to FLL bypassed internal (FBI) mode. 8.4.1.8 Bypassed Low Power External (BLPE) The bypassed low power external (BLPE) mode is entered when all the following conditions occur: * CLKS bits are written to 10 * IREFS bit is written to 0 * PLLS bit is written to 0 or 1 MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 149 Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) * * LP bit is written to 1 BDM mode is not active In bypassed low power external mode, the MCGOUT clock is derived from the external reference clock. The external reference clock which is enabled can be an external crystal/resonator or it can be another external clock source. The PLL and the FLL are disabled at all times in BLPE mode and the MCGLCLK will not be available for BDC communications. If the BDM becomes active the mode will switch to one of the bypassed external modes as determined by the state of the PLLS bit. 8.4.1.9 Stop Stop mode is entered whenever the MCU enters a STOP state. In this mode, the FLL and PLL are disabled and all MCG clock signals are static except in the following cases: MCGIRCLK will be active in stop mode when all the following conditions occur: * IRCLKEN = 1 * IREFSTEN = 1 MCGERCLK will be active in stop mode when all the following conditions occur: * ERCLKEN = 1 * EREFSTEN = 1 8.4.2 Mode Switching When switching between engaged internal and engaged external modes the IREFS bit can be changed at anytime, but the RDIV bits must be changed simultaneously so that the reference frequency stays in the range required by the state of the PLLS bit (31.25 kHz to 39.0625 kHz if the FLL is selected, or 1 MHz to 2 MHz if the PLL is selected). After a change in the IREFS value the FLL or PLL will begin locking again after the switch is completed. The completion of the switch is shown by the IREFST bit . For the special case of entering stop mode immediately after switching to FBE mode, if the external clock and the internal clock are disabled in stop mode, (EREFSTEN = 0 and IREFSTEN = 0), it is necessary to allow 100us after the IREFST bit is cleared to allow the internal reference to shutdown. For most cases the delay due to instruction execution times will be sufficient. The CLKS bits can also be changed at anytime, but in order for the MCGLCLK to be configured correctly the RDIV bits must be changed simultaneously so that the reference frequency stays in the range required by the state of the PLLS bit (31.25 kHz to 39.0625 kHz if the FLL is selected, or 1 MHz to 2MHz if the PLL is selected). The actual switch to the newly selected clock will be shown by the CLKST bits. If the newly selected clock is not available, the previous clock will remain selected. For details see Figure 8-8. MC9S08DZ60 Series Data Sheet, Rev. 4 150 Freescale Semiconductor Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) 8.4.3 Bus Frequency Divider The BDIV bits can be changed at anytime and the actual switch to the new frequency will occur immediately. 8.4.4 Low Power Bit Usage The low power bit (LP) is provided to allow the FLL or PLL to be disabled and thus conserve power when these systems are not being used. However, in some applications it may be desirable to enable the FLL or PLL and allow it to lock for maximum accuracy before switching to an engaged mode. Do this by writing the LP bit to 0. 8.4.5 Internal Reference Clock When IRCLKEN is set the internal reference clock signal will be presented as MCGIRCLK, which can be used as an additional clock source. The MCGIRCLK frequency can be re-targeted by trimming the period of the internal reference clock. This can be done by writing a new value to the TRIM bits in the MCGTRM register. Writing a larger value will decrease the MCGIRCLK frequency, and writing a smaller value to the MCGTRM register will increase the MCGIRCLK frequency. The TRIM bits will effect the MCGOUT frequency if the MCG is in FLL engaged internal (FEI), FLL bypassed internal (FBI), or bypassed low power internal (BLPI) mode. The TRIM and FTRIM value is initialized by POR but is not affected by other resets. Until MCGIRCLK is trimmed, programming low reference divider (RDIV) factors may result in MCGOUT frequencies that exceed the maximum chip-level frequency and violate the chip-level clock timing specifications (see the Device Overview chapter). If IREFSTEN and IRCLKEN bits are both set, the internal reference clock will keep running during stop mode in order to provide a fast recovery upon exiting stop. 8.4.6 External Reference Clock The MCG module can support an external reference clock with frequencies between 31.25 kHz to 5 MHz in FEE and FBE modes, 1 MHz to 16 MHz in PEE and PBE modes, and 0 to 40 MHz in BLPE mode. When ERCLKEN is set, the external reference clock signal will be presented as MCGERCLK, which can be used as an additional clock source. When IREFS = 1, the external reference clock will not be used by the FLL or PLL and will only be used as MCGERCLK. In these modes, the frequency can be equal to the maximum frequency the chip-level timing specifications will support (see the Device Overview chapter). If EREFSTEN and ERCLKEN bits are both set or the MCG is in FEE, FBE, PEE, PBE or BLPE mode, the external reference clock will keep running during stop mode in order to provide a fast recovery upon exiting stop. If CME bit is written to 1, the clock monitor is enabled. If the external reference falls below a certain frequency (floc_high or floc_low depending on the RANGE bit in the MCGC2), the MCU will reset. The LOC bit in the System Reset Status (SRS) register will be set to indicate the error. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 151 Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) 8.4.7 Fixed Frequency Clock The MCG presents the divided reference clock as MCGFFCLK for use as an additional clock source. The MCGFFCLK frequency must be no more than 1/4 of the MCGOUT frequency to be valid. Because of this requirement, the MCGFFCLK is not valid in bypass modes for the following combinations of BDIV and RDIV values: * BDIV=00 (divide by 1), RDIV < 010 * BDIV=01 (divide by 2), RDIV < 011 When MCGFFCLK is valid then MCGFFCLKVALID is set to 1. When MCGFFCLK is not valid then MCGFFCLKVALID is set to 0. 8.5 Initialization / Application Information This section describes how to initialize and configure the MCG module in application. The following sections include examples on how to initialize the MCG and properly switch between the various available modes. 8.5.1 MCG Module Initialization Sequence The MCG comes out of reset configured for FEI mode with the BDIV set for divide-by-2. The internal reference will stabilize in tirefst microseconds before the FLL can acquire lock. As soon as the internal reference is stable, the FLL will acquire lock in tfll_lock milliseconds. Upon POR, the internal reference will require trimming to guarantee an accurate clock. Freescale recommends using FLASH location 0xFFAE for storing the fine trim bit, FTRIM in the MCGSC register, and 0xFFAF for storing the 8-bit trim value in the MCGTRM register. The MCU will not automatically copy the values in these FLASH locations to the respective registers. Therefore, user code must copy these values from FLASH to the registers. NOTE The BDIV value should not be changed to divide-by-1 without first trimming the internal reference. Failure to do so could result in the MCU running out of specification. 8.5.1.1 Initializing the MCG Because the MCG comes out of reset in FEI mode, the only MCG modes which can be directly switched to upon reset are FEE, FBE, and FBI modes (see Figure 8-8). Reaching any of the other modes requires first configuring the MCG for one of these three initial modes. Care must be taken to check relevant status bits in the MCGSC register reflecting all configuration changes within each mode. To change from FEI mode to FEE or FBE modes, follow this procedure: 1. Enable the external clock source by setting the appropriate bits in MCGC2. 2. Write to MCGC1 to select the clock mode. MC9S08DZ60 Series Data Sheet, Rev. 4 152 Freescale Semiconductor Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) -- If entering FEE, set RDIV appropriately, clear the IREFS bit to switch to the external reference, and leave the CLKS bits at %00 so that the output of the FLL is selected as the system clock source. -- If entering FBE, clear the IREFS bit to switch to the external reference and change the CLKS bits to %10 so that the external reference clock is selected as the system clock source. The RDIV bits should also be set appropriately here according to the external reference frequency because although the FLL is bypassed, it is still on in FBE mode. -- The internal reference can optionally be kept running by setting the IRCLKEN bit. This is useful if the application will switch back and forth between internal and external modes. For minimum power consumption, leave the internal reference disabled while in an external clock mode. 3. After the proper configuration bits have been set, wait for the affected bits in the MCGSC register to be changed appropriately, reflecting that the MCG has moved into the proper mode. -- If ERCLKEN was set in step 1 or the MCG is in FEE, FBE, PEE, PBE, or BLPE mode, and EREFS was also set in step 1, wait here for the OSCINIT bit to become set indicating that the external clock source has finished its initialization cycles and stabilized. Typical crystal startup times are given in Appendix A, "Electrical Characteristics". -- If in FEE mode, check to make sure the IREFST bit is cleared and the LOCK bit is set before moving on. -- If in FBE mode, check to make sure the IREFST bit is cleared, the LOCK bit is set, and the CLKST bits have changed to %10 indicating the external reference clock has been appropriately selected. Although the FLL is bypassed in FBE mode, it is still on and will lock in FBE mode. To change from FEI clock mode to FBI clock mode, follow this procedure: 1. Change the CLKS bits to %01 so that the internal reference clock is selected as the system clock source. 2. Wait for the CLKST bits in the MCGSC register to change to %01, indicating that the internal reference clock has been appropriately selected. 8.5.2 MCG Mode Switching When switching between operational modes of the MCG, certain configuration bits must be changed in order to properly move from one mode to another. Each time any of these bits are changed (PLLS, IREFS, CLKS, or EREFS), the corresponding bits in the MCGSC register (PLLST, IREFST, CLKST, or OSCINIT) must be checked before moving on in the application software. Additionally, care must be taken to ensure that the reference clock divider (RDIV) is set properly for the mode being switched to. For instance, in PEE mode, if using a 4 MHz crystal, RDIV must be set to %001 (divide-by-2) or %010 (divide -by-4) in order to divide the external reference down to the required frequency between 1 and 2 MHz. The RDIV and IREFS bits should always be set properly before changing the PLLS bit so that the FLL or PLL clock has an appropriate reference clock frequency to switch to. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 153 Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) The table below shows MCGOUT frequency calculations using RDIV, BDIV, and VDIV settings for each clock mode. The bus frequency is equal to MCGOUT divided by 2. Table 8-6. MCGOUT Frequency Calculation Options fMCGOUT1 Clock Mode Note FEI (FLL engaged internal) (fint * 1024) / B Typical fMCGOUT = 16 MHz immediately after reset. RDIV bits set to %000. FEE (FLL engaged external) (fext / R *1024) / B fext / R must be in the range of 31.25 kHz to 39.0625 kHz FBE (FLL bypassed external) fext / B fext / R must be in the range of 31.25 kHz to 39.0625 kHz FBI (FLL bypassed internal) fint / B Typical fint = 32 kHz PEE (PLL engaged external) [(fext / R) * M] / B fext / R must be in the range of 1 MHz to 2 MHz PBE (PLL bypassed external) fext / B fext / R must be in the range of 1 MHz to 2 MHz BLPI (Bypassed low power internal) fint / B BLPE (Bypassed low power external) fext / B 1 R is the reference divider selected by the RDIV bits, B is the bus frequency divider selected by the BDIV bits, and M is the multiplier selected by the VDIV bits. This section will include 3 mode switching examples using a 4 MHz external crystal. If using an external clock source less than 1 MHz, the MCG should not be configured for any of the PLL modes (PEE and PBE). 8.5.2.1 Example # 1: Moving from FEI to PEE Mode: External Crystal = 4 MHz, Bus Frequency = 8 MHz In this example, the MCG will move through the proper operational modes from FEI to PEE mode until the 4 MHz crystal reference frequency is set to achieve a bus frequency of 8 MHz. Because the MCG is in FEI mode out of reset, this example also shows how to initialize the MCG for PEE mode out of reset. First, the code sequence will be described. Then a flowchart will be included which illustrates the sequence. 1. First, FEI must transition to FBE mode: a) MCGC2 = 0x36 (%00110110) - BDIV (bits 7 and 6) set to %00, or divide-by-1 - RANGE (bit 5) set to 1 because the frequency of 4 MHz is within the high frequency range - HGO (bit 4) set to 1 to configure external oscillator for high gain operation - EREFS (bit 2) set to 1, because a crystal is being used - ERCLKEN (bit 1) set to 1 to ensure the external reference clock is active b) Loop until OSCINIT (bit 1) in MCGSC is 1, indicating the crystal selected by the EREFS bit has been initialized. MC9S08DZ60 Series Data Sheet, Rev. 4 154 Freescale Semiconductor Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) c) MCGC1 = 0xB8 (%10111000) - CLKS (bits 7 and 6) set to %10 in order to select external reference clock as system clock source - RDIV (bits 5-3) set to %111, or divide-by-128 because 4 MHz / 128 = 31.25 kHz which is in the 31.25 kHz to 39.0625 kHz range required by the FLL - IREFS (bit 2) cleared to 0, selecting the external reference clock d) Loop until IREFST (bit 4) in MCGSC is 0, indicating the external reference is the current source for the reference clock e) Loop until CLKST (bits 3 and 2) in MCGSC are %10, indicating that the external reference clock is selected to feed MCGOUT 2. Then, FBE must transition either directly to PBE mode or first through BLPE mode and then to PBE mode: a) BLPE: If a transition through BLPE mode is desired, first set LP (bit 3) in MCGC2 to 1. b) BLPE/PBE: MCGC1 = 0x90 (%10010000) - RDIV (bits 5-3) set to %010, or divide-by-4 because 4 MHz / 4 = 1 MHz which is in the 1 MHz to 2 MHz range required by the PLL. In BLPE mode, the configuration of the RDIV does not matter because both the FLL and PLL are disabled. Changing them only sets up the the dividers for PLL usage in PBE mode c) BLPE/PBE: MCGC3 = 0x44 (%01000100) - PLLS (bit 6) set to 1, selects the PLL. In BLPE mode, changing this bit only prepares the MCG for PLL usage in PBE mode - VDIV (bits 3-0) set to %0100, or multiply-by-16 because 1 MHz reference * 16 = 16 MHz. In BLPE mode, the configuration of the VDIV bits does not matter because the PLL is disabled. Changing them only sets up the multiply value for PLL usage in PBE mode d) BLPE: If transitioning through BLPE mode, clear LP (bit 3) in MCGC2 to 0 here to switch to PBE mode e) PBE: Loop until PLLST (bit 5) in MCGSC is set, indicating that the current source for the PLLS clock is the PLL f) PBE: Then loop until LOCK (bit 6) in MCGSC is set, indicating that the PLL has acquired lock 3. Last, PBE mode transitions into PEE mode: a) MCGC1 = 0x10 (%00010000) - CLKS (bits7 and 6) in MCGSC1 set to %00 in order to select the output of the PLL as the system clock source b) Loop until CLKST (bits 3 and 2) in MCGSC are %11, indicating that the PLL output is selected to feed MCGOUT in the current clock mode - Now, With an RDIV of divide-by-4, a BDIV of divide-by-1, and a VDIV of multiply-by-16, MCGOUT = [(4 MHz / 4) * 16] / 1 = 16 MHz, and the bus frequency is MCGOUT / 2, or 8 MHz MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 155 Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) START IN FEI MODE MCGC2 = $36 IN BLPE MODE ? (LP=1) CHECK NO NO YES OSCINIT = 1 ? MCGC2 = $36 (LP = 0) YES MCGC1 = $B8 CHECK PLLST = 1? CHECK NO NO YES IREFST = 0? YES CHECK LOCK = 1? CHECK CLKST = %10? NO NO YES MCGC1 = $10 YES ENTER BLPE MODE ? NO CHECK CLKST = %11? NO YES YES MCGC2 = $3E (LP = 1) CONTINUE IN PEE MODE MCGC1 = $90 MCGC3 = $44 Figure 8-9. Flowchart of FEI to PEE Mode Transition using a 4 MHz crystal MC9S08DZ60 Series Data Sheet, Rev. 4 156 Freescale Semiconductor Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) 8.5.2.2 Example # 2: Moving from PEE to BLPI Mode: External Crystal = 4 MHz, Bus Frequency =16 kHz In this example, the MCG will move through the proper operational modes from PEE mode with a 4 MHz crystal configured for an 8 MHz bus frequency (see previous example) to BLPI mode with a 16 kHz bus frequency.First, the code sequence will be described. Then a flowchart will be included which illustrates the sequence. 1. First, PEE must transition to PBE mode: a) MCGC1 = 0x90 (%10010000) - CLKS (bits 7 and 6) set to %10 in order to switch the system clock source to the external reference clock b) Loop until CLKST (bits 3 and 2) in MCGSC are %10, indicating that the external reference clock is selected to feed MCGOUT 2. Then, PBE must transition either directly to FBE mode or first through BLPE mode and then to FBE mode: a) BLPE: If a transition through BLPE mode is desired, first set LP (bit 3) in MCGC2 to 1 b) BLPE/FBE: MCGC1 = 0xB8 (%10111000) - RDIV (bits 5-3) set to %111, or divide-by-128 because 4 MHz / 128 = 31.25 kHz which is in the 31.25 kHz to 39.0625 kHz range required by the FLL. In BLPE mode, the configuration of the RDIV does not matter because both the FLL and PLL are disabled. Changing them only sets up the dividers for FLL usage in FBE mode c) BLPE/FBE: MCGC3 = 0x04 (%00000100) - PLLS (bit 6) clear to 0 to select the FLL. In BLPE mode, changing this bit only prepares the MCG for FLL usage in FBE mode. With PLLS = 0, the VDIV value does not matter. d) BLPE: If transitioning through BLPE mode, clear LP (bit 3) in MCGC2 to 0 here to switch to FBE mode e) FBE: Loop until PLLST (bit 5) in MCGSC is clear, indicating that the current source for the PLLS clock is the FLL f) FBE: Optionally, loop until LOCK (bit 6) in the MCGSC is set, indicating that the FLL has acquired lock. Although the FLL is bypassed in FBE mode, it is still enabled and running. 3. Next, FBE mode transitions into FBI mode: a) MCGC1 = 0x44 (%01000100) - CLKS (bits7 and 6) in MCGSC1 set to %01 in order to switch the system clock to the internal reference clock - IREFS (bit 2) set to 1 to select the internal reference clock as the reference clock source - RDIV (bits 5-3) set to %000, or divide-by-1 because the trimmed internal reference should be within the 31.25 kHz to 39.0625 kHz range required by the FLL b) Loop until IREFST (bit 4) in MCGSC is 1, indicating the internal reference clock has been selected as the reference clock source c) Loop until CLKST (bits 3 and 2) in MCGSC are %01, indicating that the internal reference clock is selected to feed MCGOUT MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 157 Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) 4. Lastly, FBI transitions into BLPI mode. a) MCGC2 = 0x08 (%00001000) - LP (bit 3) in MCGSC is 1 START IN PEE MODE MCGC1 = $90 CHECK PLLST = 0? CHECK NO CLKST = %10 ? YES YES OPTIONAL: CHECK LOCK = 1? ENTER NO NO NO BLPE MODE ? YES MCGC1 = $44 YES MCGC2 = $3E CHECK IREFST = 0? MCGC1 = $B8 MCGC3 = $04 IN BLPE MODE ? (LP=1) NO YES NO CHECK CLKST = %01? NO YES YES MCGC2 = $36 (LP = 0) MCGC2 = $08 CONTINUE IN BLPI MODE Figure 8-10. Flowchart of PEE to BLPI Mode Transition using a 4 MHz crystal MC9S08DZ60 Series Data Sheet, Rev. 4 158 Freescale Semiconductor Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) 8.5.2.3 Example #3: Moving from BLPI to FEE Mode: External Crystal = 4 MHz, Bus Frequency = 16 MHz In this example, the MCG will move through the proper operational modes from BLPI mode at a 16 kHz bus frequency running off of the internal reference clock (see previous example) to FEE mode using a 4 MHz crystal configured for a 16 MHz bus frequency. First, the code sequence will be described. Then a flowchart will be included which illustrates the sequence. 1. First, BLPI must transition to FBI mode. a) MCGC2 = 0x00 (%00000000) - LP (bit 3) in MCGSC is 0 b) Optionally, loop until LOCK (bit 6) in the MCGSC is set, indicating that the FLL has acquired lock. Although the FLL is bypassed in FBI mode, it is still enabled and running. 2. Next, FBI will transition to FEE mode. a) MCGC2 = 0x36 (%00110110) - RANGE (bit 5) set to 1 because the frequency of 4 MHz is within the high frequency range - HGO (bit 4) set to 1 to configure external oscillator for high gain operation - EREFS (bit 2) set to 1, because a crystal is being used - ERCLKEN (bit 1) set to 1 to ensure the external reference clock is active b) Loop until OSCINIT (bit 1) in MCGSC is 1, indicating the crystal selected by the EREFS bit has been initialized. c) MCGC1 = 0x38 (%00111000) - CLKS (bits 7 and 6) set to %00 in order to select the output of the FLL as system clock source - RDIV (bits 5-3) set to %111, or divide-by-128 because 4 MHz / 128 = 31.25 kHz which is in the 31.25 kHz to 39.0625 kHz range required by the FLL - IREFS (bit 1) cleared to 0, selecting the external reference clock d) Loop until IREFST (bit 4) in MCGSC is 0, indicating the external reference clock is the current source for the reference clock e) Optionally, loop until LOCK (bit 6) in the MCGSC is set, indicating that the FLL has reacquired lock. f) Loop until CLKST (bits 3 and 2) in MCGSC are %00, indicating that the output of the FLL is selected to feed MCGOUT MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 159 Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) START IN BLPI MODE CHECK NO IREFST = 0? MCGC2 = $00 YES OPTIONAL: CHECK LOCK = 1? NO OPTIONAL: CHECK LOCK = 1? NO YES YES MCGC2 = $36 CHECK CLKST = %00? CHECK NO NO YES OSCINIT = 1 ? CONTINUE YES IN FEE MODE MCGC1 = $38 Figure 8-11. Flowchart of BLPI to FEE Mode Transition using a 4 MHz crystal 8.5.2.4 Example # 4: Moving from FEI to PEE Mode: External Crystal = 8 MHz, Bus Frequency = 8 MHz In this example, the MCG will move through the proper operational modes from FEI to PEE mode until the 8 MHz crystal reference frequency is set to achieve a bus frequency of 8 MHz. This example is similar to example number one except that in this case the frequency of the external crystal is 8 MHz instead of 4 MHz. Special consideration must be taken with this case since there is a period of time along the way from FEI mode to PEE mode where the FLL operates based on a reference clock with a frequency that is greater than the maximum allowed for the FLL. This occurs because with an 8 MHz MC9S08DZ60 Series Data Sheet, Rev. 4 160 Freescale Semiconductor Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) external crystal and a maximum reference divider factor of 128, the resulting frequency of the reference clock for the FLL is 62.5 kHz (greater than the 39.0625 kHz maximum allowed). Care must be taken in the software to minimize the amount of time spent in this state where the FLL is operating in this condition. The following code sequence describes how to move from FEI mode to PEE mode until the 8 MHz crystal reference frequency is set to achieve a bus frequency of 8 MHz. Because the MCG is in FEI mode out of reset, this example also shows how to initialize the MCG for PEE mode out of reset. First, the code sequence will be described. Then a flowchart will be included which illustrates the sequence. 1. First, FEI must transition to FBE mode: a) MCGC2 = 0x36 (%00110110) - BDIV (bits 7 and 6) set to %00, or divide-by-1 - RANGE (bit 5) set to 1 because the frequency of 8 MHz is within the high frequency range - HGO (bit 4) set to 1 to configure external oscillator for high gain operation - EREFS (bit 2) set to 1, because a crystal is being used - ERCLKEN (bit 1) set to 1 to ensure the external reference clock is active b) Loop until OSCINIT (bit 1) in MCGSC is 1, indicating the crystal selected by the EREFS bit has been initialized. c) Block Interrupts (If applicable by setting the interrupt bit in the CCR). d) MCGC1 = 0xB8 (%10111000) - CLKS (bits 7 and 6) set to %10 in order to select external reference clock as system clock source - RDIV (bits 5-3) set to %111, or divide-by-128. NOTE 8 MHz / 128 = 62.5 kHz which is greater than the 31.25 kHz to 39.0625 kHz range required by the FLL. Therefore after the transition to FBE is complete, software must progress through to BLPE mode immediately by setting the LP bit in MCGC2. - IREFS (bit 2) cleared to 0, selecting the external reference clock e) Loop until IREFST (bit 4) in MCGSC is 0, indicating the external reference is the current source for the reference clock f) Loop until CLKST (bits 3 and 2) in MCGSC are %10, indicating that the external reference clock is selected to feed MCGOUT 2. Then, FBE mode transitions into BLPE mode: a) MCGC2 = 0x3E (%00111110) - LP (bit 3) in MCGC2 to 1 (BLPE mode entered) NOTE There must be no extra steps (including interrupts) between steps 1d and 2a. b) Enable Interrupts (if applicable by clearing the interrupt bit in the CCR). MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 161 Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) c) MCGC1 = 0x98 (%10011000) - RDIV (bits 5-3) set to %011, or divide-by-8 because 8 MHz / 8= 1 MHz which is in the 1 MHz to 2 MHz range required by the PLL. In BLPE mode, the configuration of the RDIV does not matter because both the FLL and PLL are disabled. Changing them only sets up the the dividers for PLL usage in PBE mode d) MCGC3 = 0x44 (%01000100) - PLLS (bit 6) set to 1, selects the PLL. In BLPE mode, changing this bit only prepares the MCG for PLL usage in PBE mode - VDIV (bits 3-0) set to %0100, or multiply-by-16 because 1 MHz reference * 16 = 16 MHz. In BLPE mode, the configuration of the VDIV bits does not matter because the PLL is disabled. Changing them only sets up the multiply value for PLL usage in PBE mode e) Loop until PLLST (bit 5) in MCGSC is set, indicating that the current source for the PLLS clock is the PLL 3. Then, BLPE mode transitions into PBE mode: a) Clear LP (bit 3) in MCGC2 to 0 here to switch to PBE mode b) Then loop until LOCK (bit 6) in MCGSC is set, indicating that the PLL has acquired lock 4. Last, PBE mode transitions into PEE mode: a) MCGC1 = 0x18 (%00011000) - CLKS (bits7 and 6) in MCGSC1 set to %00 in order to select the output of the PLL as the system clock source b) Loop until CLKST (bits 3 and 2) in MCGSC are %11, indicating that the PLL output is selected to feed MCGOUT in the current clock mode - Now, With an RDIV of divide-by-8, a BDIV of divide-by-1, and a VDIV of multiply-by-16, MCGOUT = [(8 MHz / 8) * 16] / 1 = 16 MHz, and the bus frequency is MCGOUT / 2, or 8 MHz MC9S08DZ60 Series Data Sheet, Rev. 4 162 Freescale Semiconductor Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) START IN FEI MODE MCGC2 = $36 CHECK NO CHECK PLLST = 1? NO OSCINIT = 1 ? YES YES MCGC2 = $36 (LP = 0) MCGC1 = $B8 CHECK NO IREFST = 0? CHECK LOCK = 1? NO YES YES CHECK CLKST = %10? NO MCGC1 = $18 YES CHECK CLKST = %11? MCGC2 = $3E (LP = 1) NO YES MCGC1 = $98 MCGC3 = $44 CONTINUE IN PEE MODE Figure 8-12. Flowchart of FEI to PEE Mode Transition using a 8 MHz crystal MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 163 Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) 8.5.3 Calibrating the Internal Reference Clock (IRC) The IRC is calibrated by writing to the MCGTRM register first, then using the FTRIM bit to "fine tune" the frequency. We will refer to this total 9-bit value as the trim value, ranging from 0x000 to 0x1FF, where the FTRIM bit is the LSB. The trim value after a POR is always 0x100 (MCGTRM = 0x80 and FTRIM = 0). Writing a larger value will decrease the frequency and smaller values will increase the frequency. The trim value is linear with the period, except that slight variations in wafer fab processing produce slight non-linearities between trim value and period. These non-linearities are why an iterative trimming approach to search for the best trim value is recommended. In Example #5: Internal Reference Clock Trim this approach will be demonstrated. After a trim value has been found for a device, this value can be stored in FLASH memory to save the value. If power is removed from the device, the IRC can easily be re-trimmed by copying the saved value from FLASH to the MCG registers. Freescale identifies recommended FLASH locations for storing the trim value for each MCU. Consult the memory map in the data sheet for these locations. On devices that are factory trimmed, the factory trim value will be stored in these locations. 8.5.3.1 Example #5: Internal Reference Clock Trim For applications that require a tight frequency tolerance, a trimming procedure is provided that will allow a very accurate internal clock source. This section outlines one example of trimming the internal oscillator. Many other possible trimming procedures are valid and can be used. In the example below, the MCG trim will be calibrated for the 9-bit MCGTRM and FTRIM collective value. This value will be referred to as TRMVAL. MC9S08DZ60 Series Data Sheet, Rev. 4 164 Freescale Semiconductor Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) Initial conditions: 1) Clock supplied from ATE has 500 s duty period 2) MCG configured for internal reference with 8MHz bus START TRIM PROCEDURE TRMVAL = $100 n=1 MEASURE INCOMING CLOCK WIDTH (COUNT = # OF BUS CLOCKS / 8) COUNT < EXPECTED = 500 (RUNNING TOO SLOW) . CASE STATEMENT COUNT = EXPECTED = 500 COUNT > EXPECTED = 500 (RUNNING TOO FAST) TRMVAL = TRMVAL - 256/ (2**n) (DECREASING TRMVAL INCREASES THE FREQUENCY) TRMVAL = TRMVAL + 256/ (2**n) (INCREASING TRMVAL DECREASES THE FREQUENCY) STORE MCGTRM AND FTRIM VALUES IN NON-VOLATILE MEMORY CONTINUE n = n+1 YES IS n > 9? NO Figure 8-13. Trim Procedure In this particular case, the MCU has been attached to a PCB and the entire assembly is undergoing final test with automated test equipment. A separate signal or message is provided to the MCU operating under user provided software control. The MCU initiates a trim procedure as outlined in Figure 8-13 while the tester supplies a precision reference signal. If the intended bus frequency is near the maximum allowed for the device, it is recommended to trim using a reference divider value (RDIV setting) of twice the final value. After the trim procedure is complete, the reference divider can be restored. This will prevent accidental overshoot of the maximum clock frequency. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 165 Chapter 8 Multi-Purpose Clock Generator (S08MCGV1) MC9S08DZ60 Series Data Sheet, Rev. 4 166 Freescale Semiconductor Chapter 9 Analog Comparator (S08ACMPV3) 9.1 Introduction The analog comparator module (ACMP) provides a circuit for comparing two analog input voltages or for comparing one analog input voltage to an internal reference voltage. The comparator circuit is designed to operate across the full range of the supply voltage (rail-to-rail operation). All MC9S08DZ60 Series MCUs have two full function ACMPs in a 64-pin package. MCUs in the 48-pin package have two ACMPs, but the output of ACMP2 is not accessible. MCUs in the 32-pin package contain one full function ACMP. NOTE MC9S08DZ60 Series devices operate at a higher voltage range (2.7 V to 5.5 V) and do not include stop1 mode. Please ignore references to stop1. 9.1.1 ACMP Configuration Information When using the bandgap reference voltage for input to ACMP+, the user must enable the bandgap buffer by setting BGBE =1 in SPMSC1 see Section 5.8.7, "System Power Management Status and Control 1 Register (SPMSC1)." For value of bandgap voltage reference see Section A.6, "DC Characteristics." MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 167 PORT A PTA7/PIA7/ADP7/IRQ PTA6/PIA6/ADP6 PTA5/PIA5/ADP5 PTA4/PIA4/ADP4 PTA3/PIA3/ADP3/ACMP1O PTA2/PIA2/ADP2/ACMP1PTA1/PIA1/ADP1/ACMP1+ PTA0/PIA0/ADP0/MCLK PORT B PTB7/PIB7/ADP15 PTB6/PIB6/ADP14 PTB5/PIB5/ADP13 PTB4/PIB4/ADP12 PTB3/PIB3/ADP11 PTB2/PIB2/ADP10 PTB1/PIB1/ADP9 PTB0/PIB0/ADP8 PORT C PTC7/ADP23 PTC6/ADP22 PTC5/ADP21 PTC4/ADP20 PTC3/ADP19 PTC2/ADP18 PTC1/ADP17 PTC0/ADP16 PORT D PTD7/PID7/TPM1CH5 PTD6/PID6/TPM1CH4 PTD5/PID5/TPM1CH3 PTD4/PID4/TPM1CH2 PTD3/PID3/TPM1CH1 PTD2/PID2/TPM1CH0 PTD1/PID1/TPM2CH1 PTD0/PID0/TPM2CH0 PORT E PTE7/RxD2/RXCAN PTE6/TxD2/TXCAN PTE5/SDA/MISO PTE4/SCL/MOSI PTE3/SPSCK PTE2/SS PTE1/RxD1 PTE0/TxD1 PORT F PTF7 PTF6/ACMP2O PTF5/ACMP2PTF4/ACMP2+ PTF3/TPM2CLK/SDA PTF2/TPM1CLK/SCL PTF1/RxD2 PTF0/TxD2 PORT G Chapter 9 Analog Comparator (S08ACMPV3) PTG5 PTG4 PTG3 PTG2 PTG1/XTAL PTG0/EXTAL HCS08 CORE CPU BKGD/MS BDC ANALOG COMPARATOR (ACMP1) BKP ACMP1O ACMP1ACMP1+ HCS08 SYSTEM CONTROL RESETS AND INTERRUPTS MODES OF OPERATION POWER MANAGEMENT COP LVD INT IRQ ADP7-ADP0 24-CHANNEL,12-BIT ANALOG-TO-DIGITAL CONVERTER (ADC) VREFH VREFL VDDA VSSA USER FLASH MC9S0DZ60 = 60K MC9S0DZ48 = 48K MC9S0DZ32 = 32K MC9S0DZ16 = 16K USER EEPROM MC9S0DZ60 = 2K TPM1CH5 TPM1CH0 6 TPM1CLK 2-CHANNEL TIMER/PWM MODULE (TPM2) TPM2CH1, TPM2CH0 TPM2CLK CONTROLLER AREA NETWORK (MSCAN) SERIAL PERIPHERAL INTERFACE MODULE (SPI) DEBUG MODULE (DBG) SERIAL COMMUNICATIONS INTERFACE (SCI1) VOLTAGE REGULATOR ADP15-ADP8 ADP23-ADP16 6-CHANNEL TIMER/PWM MODULE (TPM1) USER RAM MC9S0DZ60 = 4K REAL-TIME COUNTER (RTC) VDD VDD VSS VSS 8 IRQ RESET ANALOG COMPARATOR (ACMP2) IIC MODULE (IIC) SERIAL COMMUNICATIONS INTERFACE (SCI2) RxCAN TxCAN MISO MOSI SPSCK SS RxD1 TxD1 ACMP2O ACMP2ACMP2+ SDA SCL RxD2 TxD2 MULTI-PURPOSE CLOCK GENERATOR (MCG) XTAL EXTAL OSCILLATOR (XOSC) - VREFH/VREFL internally connected to VDDA/VSSA in 48-pin and 32-pin packages - VDD and VSS pins are each internally connected to two pads in 32-pin package - Pin not connected in 48-pin and 32-pin packages - Pin not connected in 32-pin package Figure 9-1. MC9S08DZ60 Block Diagram MC9S08DZ60 Series Data Sheet, Rev. 4 168 Freescale Semiconductor Chapter 9 Analog Comparator (S08ACMPV3) 9.1.2 Features The ACMP has the following features: * Full rail to rail supply operation. * Selectable interrupt on rising edge, falling edge, or either rising or falling edges of comparator output. * Option to compare to fixed internal bandgap reference voltage. * Option to allow comparator output to be visible on a pin, ACMPxO. 9.1.3 Modes of Operation This section defines the ACMP operation in wait, stop, and background debug modes. 9.1.3.1 ACMP in Wait Mode The ACMP continues to run in wait mode if enabled before executing the appropriate instruction. Therefore, the ACMP can be used to bring the MCU out of wait mode if the ACMP interrupt is enabled (ACIE is set). For lowest possible current consumption, the ACMP should be disabled by software if not required as an interrupt source during wait mode. 9.1.3.2 ACMP in Stop Modes The ACMP is disabled in all stop modes, regardless of the settings before executing the stop instruction. Therefore, the ACMP cannot be used as a wake up source from stop modes. During stop2 mode, the ACMP module is fully powered down. Upon wake-up from stop2 mode, the ACMP module is in the reset state. During stop3 mode, clocks to the ACMP module are halted. No registers are affected. In addition, the ACMP comparator circuit enters a low-power state. No compare operation occurs while in stop3. If stop3 is exited with a reset, the ACMP is put into its reset state. If stop3 is exited with an interrupt, the ACMP continues from the state it was in when stop3 was entered. 9.1.3.3 ACMP in Active Background Mode When the microcontroller is in active background mode, the ACMP continues to operate normally. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 169 Chapter 9 Analog Comparator (S08ACMPV3) 9.1.4 Block Diagram The block diagram for the analog comparator module is shown Figure 9-2. Internal Bus Internal Reference ACIE ACBGS ACME Status & Control Register ACMPx INTERRUPT REQUEST ACF ACMPx+ + set ACF ACMOD ACOPE Interrupt Control Comparator ACMPx- ACMPxO Figure 9-2. Analog Comparator (ACMP) Block Diagram 9.2 External Signal Description The ACMP has two analog input pins, ACMPx+ and ACMPx- and one digital output pin ACMPxO. Each of these pins can accept an input voltage that varies across the full operating voltage range of the MCU. As shown in Figure 9-2, the ACMPx- pin is connected to the inverting input of the comparator, and the ACMPx+ pin is connected to the comparator non-inverting input if ACBGS is a 0. As shown in Figure 9-2, the ACMPxO pin can be enabled to drive an external pin. The signal properties of ACMP are shown in Table 9-1. Table 9-1. Signal Properties Signal Function I/O ACMPx- Inverting analog input to the ACMP. (Minus input) I ACMPx+ Non-inverting analog input to the ACMP. (Positive input) I ACMPxO Digital output of the ACMP. O MC9S08DZ60 Series Data Sheet, Rev. 4 170 Freescale Semiconductor Chapter 9 Analog Comparator (S08ACMPV3) 9.3 Memory Map/Register Definition The ACMP includes one register: * An 8-bit status and control register Refer to the direct-page register summary in the memory section of this document for the absolute address assignments for the ACMP register.This section refers to register and control bits only by their names and relative address offsets. Some MCUs may have more than one ACMP, so register names include placeholder characters (x) to identify which ACMP is being referenced. Table 9-2. ACMP Register Summary Name 7 6 5 4 ACME ACBGS ACF ACIE R 3 2 1 0 ACO ACMPxSC ACOPE ACMOD W 9.3.1 ACMPx Status and Control Register (ACMPxSC) ACMPxSC contains the status flag and control bits used to enable and configure the ACMP. 7 6 5 4 3 ACME ACBGS ACF ACIE 0 0 0 0 R 2 1 0 ACO ACOPE ACMOD W Reset: 0 0 0 0 Figure 9-3. ACMPx Status and Control Register (ACMPxSC) Table 9-3. ACMPxSC Field Descriptions Field 7 ACME Description Analog Comparator Module Enable. Enables the ACMP module. 0 ACMP not enabled 1 ACMP is enabled 6 ACBGS Analog Comparator Bandgap Select. Selects between the bandgap reference voltage or the ACMPx+ pin as the input to the non-inverting input of the analog comparator. 0 External pin ACMPx+ selected as non-inverting input to comparator 1 Internal reference select as non-inverting input to comparator 5 ACF Analog Comparator Flag. ACF is set when a compare event occurs. Compare events are defined by ACMOD. ACF is cleared by writing a one to it. 0 Compare event has not occurred 1 Compare event has occurred 4 ACIE Analog Comparator Interrupt Enable. Enables the interrupt from the ACMP. When ACIE is set, an interrupt is asserted when ACF is set. 0 Interrupt disabled 1 Interrupt enabled MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 171 Chapter 9 Analog Comparator (S08ACMPV3) Table 9-3. ACMPxSC Field Descriptions (continued) Field 3 ACO Description Analog Comparator Output. Reading ACO returns the current value of the analog comparator output. ACO is reset to a 0 and reads as a 0 when the ACMP is disabled (ACME = 0). 2 ACOPE Analog Comparator Output Pin Enable. Enables the comparator output to be placed onto the external pin, ACMPxO. 0 Analog comparator output not available on ACMPxO 1 Analog comparator output is driven out on ACMPxO 1:0 ACMOD Analog Comparator Mode. ACMOD selects the type of compare event which sets ACF. 00 Encoding 0 -- Comparator output falling edge 01 Encoding 1 -- Comparator output rising edge 10 Encoding 2 -- Comparator output falling edge 11 Encoding 3 -- Comparator output rising or falling edge 9.4 Functional Description The analog comparator can compare two analog input voltages applied to ACMPx+ and ACMPx-, or it can compare an analog input voltage applied to ACMPx- with an internal bandgap reference voltage. ACBGS selects between the bandgap reference voltage or the ACMPx+ pin as the input to the non-inverting input of the analog comparator. The comparator output is high when the non-inverting input is greater than the inverting input, and is low when the non-inverting input is less than the inverting input. ACMOD selects the condition that causes ACF to be set. ACF can be set on a rising edge of the comparator output, a falling edge of the comparator output, or a rising or a falling edge (toggle). The comparator output can be read directly through ACO. The comparator output can be driven onto the ACMPxO pin using ACOPE. MC9S08DZ60 Series Data Sheet, Rev. 4 172 Freescale Semiconductor Chapter 10 Analog-to-Digital Converter (S08ADC12V1) 10.1 Introduction The 12-bit analog-to-digital converter (ADC) is a successive approximation ADC designed for operation within an integrated microcontroller system-on-chip. NOTE MC9S08DZ60 Series devices operate at a higher voltage range (2.7 V to 5.5 V) and do not include stop1 mode. Please ignore references to stop1. 10.1.1 Analog Power and Ground Signal Names References to VDDAD and VSSAD in this chapter correspond to signals VDDA and VSSA, respectively. 10.1.2 Channel Assignments NOTE The ADC channel assignments for the MC9S08DZ60 Series devices are shown in Table 10-1. Reserved channels convert to an unknown value. This chapter shows bits for all S08ADC12V1 channels. MC9S08DZ60 Series MCUs do not use all of these channels. All bits corresponding to channels that are not available on a device are reserved. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 173 Chapter 10 Analog-to-Digital Converter (S08ADC12V1) Table 10-1. ADC Channel Assignment ADCH Channel Input ADCH Channel Input 00000 AD0 PTA0/ADP0/MCLK 01111 AD15 PTB7/ADP15 AD16 PTC0/ADP16 00001 AD1 PTA1/ADP1/ACMP1+ 10000 00010 AD2 PTA2/ADP2/ACMP1P- 10001 AD17 PTC1/ADP17 00011 AD3 PTA3/ADP3/ACMP1O 10010 AD18 PTC2/ADP18 00100 AD4 PTA4/ADP4 10011 AD19 PTC3/ADP19 AD20 PTC4/ADP20 00101 AD5 PTA5/ADP5 10100 00110 AD6 PTA6/ADP6 10101 AD21 PTC5/ADP21 00111 AD7 PTA7/ADP7 10110 AD22 PTC6/ADP22 01000 AD8 PTB0/ADP8 10111 AD23 PTC7/ADP23 AD24 through AD25 Reserved 01001 AD9 PTB1/ADP9 11000- 01010 AD10 PTB2/ADP10 11001 01011 AD11 PTB3/ADP11 11010 AD26 Temperature Sensor1 01100 AD12 PTB4/ADP12 11011 AD27 Internal Bandgap2 01101 AD13 PTB5/ADP13 11100 Reserved Reserved 01110 AD14 PTB6/ADP14 11101 VREFH VREFH 11110 V V 10.1.3 Alternate Clock The ADC module is capable of performing conversions using the MCU bus clock, the bus clock divided by two, the local asynchronous clock (ADACK) within the module, or the alternate clock, ALTCLK. The alternate clock for the MC9S08DZ60 Series MCU devices is the external reference clock (MCGERCLK). The selected clock source must run at a frequency such that the ADC conversion clock (ADCK) runs at a frequency within its specified range (fADCK) after being divided down from the ALTCLK input as determined by the ADIV bits. ALTCLK is active while the MCU is in wait mode provided the conditions described above are met. This allows ALTCLK to be used as the conversion clock source for the ADC while the MCU is in wait mode. ALTCLK cannot be used as the ADC conversion clock source while the MCU is in either stop2 or stop3. 10.1.4 Hardware Trigger The ADC hardware trigger, ADHWT, is the output from the real time counter (RTC). The RTC counter can be clocked by either MCGERCLK or a nominal 1 kHz clock source. The period of the RTC is determined by the input clock frequency, the RTCPS bits, and the RTCMOD register. When the ADC hardware trigger is enabled, a conversion is initiated upon an RTC counter overflow. The RTC can be configured to cause a hardware trigger in MCU run, wait, and stop3. MC9S08DZ60 Series Data Sheet, Rev. 4 174 Freescale Semiconductor Chapter 10 Analog-to-Digital Converter (S08ADC12V1) 10.1.5 Temperature Sensor To use the on-chip temperature sensor, the user must perform the following: * Configure ADC for long sample with a maximum of 1 MHz clock * Convert the bandgap voltage reference channel (AD27) -- By converting the digital value of the bandgap voltage reference channel using the value of VBG the user can determine VDD. For value of bandgap voltage, see Section A.6, "DC Characteristics". * Convert the temperature sensor channel (AD26) -- By using the calculated value of VDD, convert the digital value of AD26 into a voltage, VTEMP Equation 10-1 provides an approximate transfer function of the temperature sensor. Temp = 25 - ((VTEMP -VTEMP25) / m) Eqn. 10-1 where: -- VTEMP is the voltage of the temperature sensor channel at the ambient temperature. -- VTEMP25 is the voltage of the temperature sensor channel at 25C. -- m is the hot or cold voltage versus temperature slope in V/C. For temperature calculations, use the VTEMP25 and m values from the ADC Electricals table. In application code, the user reads the temperature sensor channel, calculates VTEMP, and compares to VTEMP25. If VTEMP is greater than VTEMP25 the cold slope value is applied in Equation 10-1. If VTEMP is less than VTEMP25 the hot slope value is applied in Equation 10-1. To improve accuracy the user should calibrate the bandgap voltage reference and temperature sensor. Calibrating at 25C will improve accuracy to 4.5C. Calibration at three points, -40C, 25C, and 125C will improve accuracy to 2.5C. Once calibration has been completed, the user will need to calculate the slope for both hot and cold. In application code, the user would then calculate the temperature using Equation 10-1 as detailed above and then determine if the temperature is above or below 25C. Once determined if the temperature is above or below 25C, the user can recalculate the temperature using the hot or cold slope value obtained during calibration. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 175 PORT A PTA7/PIA7/ADP7/IRQ PTA6/PIA6/ADP6 PTA5/PIA5/ADP5 PTA4/PIA4/ADP4 PTA3/PIA3/ADP3/ACMP1O PTA2/PIA2/ADP2/ACMP1PTA1/PIA1/ADP1/ACMP1+ PTA0/PIA0/ADP0/MCLK PORT B PTB7/PIB7/ADP15 PTB6/PIB6/ADP14 PTB5/PIB5/ADP13 PTB4/PIB4/ADP12 PTB3/PIB3/ADP11 PTB2/PIB2/ADP10 PTB1/PIB1/ADP9 PTB0/PIB0/ADP8 PORT C PTC7/ADP23 PTC6/ADP22 PTC5/ADP21 PTC4/ADP20 PTC3/ADP19 PTC2/ADP18 PTC1/ADP17 PTC0/ADP16 PORT D PTD7/PID7/TPM1CH5 PTD6/PID6/TPM1CH4 PTD5/PID5/TPM1CH3 PTD4/PID4/TPM1CH2 PTD3/PID3/TPM1CH1 PTD2/PID2/TPM1CH0 PTD1/PID1/TPM2CH1 PTD0/PID0/TPM2CH0 PORT E PTE7/RxD2/RXCAN PTE6/TxD2/TXCAN PTE5/SDA/MISO PTE4/SCL/MOSI PTE3/SPSCK PTE2/SS PTE1/RxD1 PTE0/TxD1 PORT F PTF7 PTF6/ACMP2O PTF5/ACMP2PTF4/ACMP2+ PTF3/TPM2CLK/SDA PTF2/TPM1CLK/SCL PTF1/RxD2 PTF0/TxD2 PORT G Chapter 10 Analog-to-Digital Converter (S08ADC12V1) PTG5 PTG4 PTG3 PTG2 PTG1/XTAL PTG0/EXTAL HCS08 CORE CPU BKGD/MS BDC ANALOG COMPARATOR (ACMP1) BKP ACMP1O ACMP1ACMP1+ HCS08 SYSTEM CONTROL RESETS AND INTERRUPTS MODES OF OPERATION POWER MANAGEMENT COP LVD INT IRQ ADP7-ADP0 24-CHANNEL,12-BIT ANALOG-TO-DIGITAL CONVERTER (ADC) VREFH VREFL VDDA VSSA USER FLASH MC9S0DZ60 = 60K MC9S0DZ48 = 48K MC9S0DZ32 = 32K MC9S0DZ16 = 16K USER EEPROM MC9S0DZ60 = 2K TPM1CH5 TPM1CH0 6 TPM1CLK 2-CHANNEL TIMER/PWM MODULE (TPM2) TPM2CH1, TPM2CH0 TPM2CLK CONTROLLER AREA NETWORK (MSCAN) SERIAL PERIPHERAL INTERFACE MODULE (SPI) DEBUG MODULE (DBG) SERIAL COMMUNICATIONS INTERFACE (SCI1) VOLTAGE REGULATOR ADP15-ADP8 ADP23-ADP16 6-CHANNEL TIMER/PWM MODULE (TPM1) USER RAM MC9S0DZ60 = 4K REAL-TIME COUNTER (RTC) VDD VDD VSS VSS 8 IRQ RESET ANALOG COMPARATOR (ACMP2) IIC MODULE (IIC) SERIAL COMMUNICATIONS INTERFACE (SCI2) RxCAN TxCAN MISO MOSI SPSCK SS RxD1 TxD1 ACMP2O ACMP2ACMP2+ SDA SCL RxD2 TxD2 MULTI-PURPOSE CLOCK GENERATOR (MCG) XTAL EXTAL OSCILLATOR (XOSC) - VREFH/VREFL internally connected to VDDA/VSSA in 48-pin and 32-pin packages - VDD and VSS pins are each internally connected to two pads in 32-pin package - Pin not connected in 48-pin and 32-pin packages - Pin not connected in 32-pin package Figure 10-1. MC9S08DZ60 Block Diagram Emphasizing the ADC Module and Pins MC9S08DZ60 Series Data Sheet, Rev. 4 176 Freescale Semiconductor Chapter 10 Analog-to-Digital Converter (S08ADC12V1) 10.1.6 Features Features of the ADC module include: * Linear successive approximation algorithm with 12-bit resolution * Up to 28 analog inputs * Output formatted in 12-, 10-, or 8-bit right-justified unsigned format * Single or continuous conversion (automatic return to idle after single conversion) * Configurable sample time and conversion speed/power * Conversion complete flag and interrupt * Input clock selectable from up to four sources * Operation in wait or stop3 modes for lower noise operation * Asynchronous clock source for lower noise operation * Selectable asynchronous hardware conversion trigger * Automatic compare with interrupt for less-than, or greater-than or equal-to, programmable value * Temperature sensor 10.1.7 ADC Module Block Diagram Figure 10-2 provides a block diagram of the ADC module. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 177 Chapter 10 Analog-to-Digital Converter (S08ADC12V1) ADIV ADLPC MODE ADLSMP ADTRG 2 ADCO ADCH 1 ADCCFG complete COCO ADCSC1 ADICLK Compare true AIEN 3 Async Clock Gen ADACK MCU STOP ADCK /2 ALTCLK abort transfer sample initialize *** AD0 convert Control Sequencer ADHWT Bus Clock Clock Divide AIEN 1 Interrupt COCO 2 ADVIN SAR Converter AD27 VREFH Data Registers Sum VREFL Compare true 3 Compare Value Registers ACFGT Value Compare Logic ADCSC2 Figure 10-2. ADC Block Diagram 10.2 External Signal Description The ADC module supports up to 28 separate analog inputs. It also requires four supply/reference/ground connections. Table 10-2. Signal Properties Name Function AD27-AD0 Analog Channel inputs VREFH High reference voltage VREFL Low reference voltage VDDAD Analog power supply VSSAD Analog ground MC9S08DZ60 Series Data Sheet, Rev. 4 178 Freescale Semiconductor Chapter 10 Analog-to-Digital Converter (S08ADC12V1) 10.2.1 Analog Power (VDDAD) The ADC analog portion uses VDDAD as its power connection. In some packages, VDDAD is connected internally to VDD. If externally available, connect the VDDAD pin to the same voltage potential as VDD. External filtering may be necessary to ensure clean VDDAD for good results. 10.2.2 Analog Ground (VSSAD) The ADC analog portion uses VSSAD as its ground connection. In some packages, VSSAD is connected internally to VSS. If externally available, connect the VSSAD pin to the same voltage potential as VSS. 10.2.3 Voltage Reference High (VREFH) VREFH is the high reference voltage for the converter. In some packages, VREFH is connected internally to VDDAD. If externally available, VREFH may be connected to the same potential as VDDAD or may be driven by an external source between the minimum VDDAD spec and the VDDAD potential (VREFH must never exceed VDDAD). 10.2.4 Voltage Reference Low (VREFL) VREFL is the low-reference voltage for the converter. In some packages, VREFL is connected internally to VSSAD. If externally available, connect the VREFL pin to the same voltage potential as VSSAD. 10.2.5 Analog Channel Inputs (ADx) The ADC module supports up to 28 separate analog inputs. An input is selected for conversion through the ADCH channel select bits. 10.3 Register Definition These memory-mapped registers control and monitor operation of the ADC: * * * * * * Status and control register, ADCSC1 Status and control register, ADCSC2 Data result registers, ADCRH and ADCRL Compare value registers, ADCCVH and ADCCVL Configuration register, ADCCFG Pin control registers, APCTL1, APCTL2, APCTL3 10.3.1 Status and Control Register 1 (ADCSC1) This section describes the function of the ADC status and control register (ADCSC1). Writing ADCSC1 aborts the current conversion and initiates a new conversion (if the ADCH bits are equal to a value other than all 1s). MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 179 Chapter 10 Analog-to-Digital Converter (S08ADC12V1) 7 R 6 5 AIEN ADCO 0 0 4 3 2 1 0 1 1 COCO ADCH W Reset: 0 1 1 1 Figure 10-3. Status and Control Register (ADCSC1) Table 10-3. ADCSC1 Field Descriptions Field Description 7 COCO Conversion Complete Flag. The COCO flag is a read-only bit set each time a conversion is completed when the compare function is disabled (ACFE = 0). When the compare function is enabled (ACFE = 1), the COCO flag is set upon completion of a conversion only if the compare result is true. This bit is cleared when ADCSC1 is written or when ADCRL is read. 0 Conversion not completed 1 Conversion completed 6 AIEN Interrupt Enable AIEN enables conversion complete interrupts. When COCO becomes set while AIEN is high, an interrupt is asserted. 0 Conversion complete interrupt disabled 1 Conversion complete interrupt enabled 5 ADCO Continuous Conversion Enable. ADCO enables continuous conversions. 0 One conversion following a write to the ADCSC1 when software triggered operation is selected, or one conversion following assertion of ADHWT when hardware triggered operation is selected. 1 Continuous conversions initiated following a write to ADCSC1 when software triggered operation is selected. Continuous conversions are initiated by an ADHWT event when hardware triggered operation is selected. 4:0 ADCH Input Channel Select. The ADCH bits form a 5-bit field that selects one of the input channels. The input channels are detailed in Table 10-4. The successive approximation converter subsystem is turned off when the channel select bits are all set. This feature allows for explicit disabling of the ADC and isolation of the input channel from all sources. Terminating continuous conversions this way prevents an additional, single conversion from being performed. It is not necessary to set the channel select bits to all ones to place the ADC in a low-power state when continuous conversions are not enabled because the module automatically enters a low-power state when a conversion completes. Table 10-4. Input Channel Select ADCH Input Select 00000-01111 AD0-15 10000-11011 AD16-27 11100 Reserved 11101 VREFH 11110 VREFL 11111 Module disabled MC9S08DZ60 Series Data Sheet, Rev. 4 180 Freescale Semiconductor Chapter 10 Analog-to-Digital Converter (S08ADC12V1) 10.3.2 Status and Control Register 2 (ADCSC2) The ADCSC2 register controls the compare function, conversion trigger, and conversion active of the ADC module. Reset: 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 Figure 10-4. Status and Control Register 2 (ADCSC2) Table 10-5. ADCSC2 Register Field Descriptions Field Description 7 ADACT Conversion Active. Indicates that a conversion is in progress. ADACT is set when a conversion is initiated and cleared when a conversion is completed or aborted. 0 Conversion not in progress 1 Conversion in progress 6 ADTRG Conversion Trigger Select. Selects the type of trigger used for initiating a conversion. Two types of triggers are selectable: software trigger and hardware trigger. When software trigger is selected, a conversion is initiated following a write to ADCSC1. When hardware trigger is selected, a conversion is initiated following the assertion of the ADHWT input. 0 Software trigger selected 1 Hardware trigger selected 5 ACFE 4 ACFGT 10.3.3 Compare Function Enable. Enables the compare function. 0 Compare function disabled 1 Compare function enabled Compare Function Greater Than Enable. Configures the compare function to trigger when the result of the conversion of the input being monitored is greater than or equal to the compare value. The compare function defaults to triggering when the result of the compare of the input being monitored is less than the compare value. 0 Compare triggers when input is less than compare value 1 Compare triggers when input is greater than or equal to compare value Data Result High Register (ADCRH) In 12-bit operation, ADCRH contains the upper four bits of the result of a 12-bit conversion. In 10-bit mode, ADCRH contains the upper two bits of the result of a 10-bit conversion. When configured for 10-bit mode, ADR[11:10] are cleared. When configured for 8-bit mode, ADR[11:8] are cleared. In 12-bit and 10-bit mode, ADCRH is updated each time a conversion completes except when automatic compare is enabled and the compare condition is not met. When a compare event does occur, the value is the addition of the conversion result and the two's complement of the compare value. In 12-bit and 10-bit mode, reading ADCRH prevents the ADC from transferring subsequent conversion results into the result registers until ADCRL is read. If ADCRL is not read until after the next conversion is completed, the intermediate conversion result is lost. In 8-bit mode, there is no interlocking with ADCRL. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 181 Chapter 10 Analog-to-Digital Converter (S08ADC12V1) If the MODE bits are changed, any data in ADCRH becomes invalid. R 7 6 5 4 3 2 1 0 0 0 0 0 ADR11 ADR10 ADR9 ADR8 0 0 0 0 0 0 0 0 W Reset: Figure 10-5. Data Result High Register (ADCRH) 10.3.4 Data Result Low Register (ADCRL) ADCRL contains the lower eight bits of the result of a 12-bit or 10-bit conversion, and all eight bits of an 8-bit conversion. This register is updated each time a conversion completes except when automatic compare is enabled and the compare condition is not met. When a compare event does occur, the value is the addition of the conversion result and the two's complement of the compare value. In 12-bit and 10-bit mode, reading ADCRH prevents the ADC from transferring subsequent conversion results into the result registers until ADCRL is read. If ADCRL is not read until the after next conversion is completed, the intermediate conversion results are lost. In 8-bit mode, there is no interlocking with ADCRH. If the MODE bits are changed, any data in ADCRL becomes invalid. R 7 6 5 4 3 2 1 0 ADR7 ADR6 ADR5 ADR4 ADR3 ADR2 ADR1 ADR0 0 0 0 0 0 0 0 0 W Reset: Figure 10-6. Data Result Low Register (ADCRL) 10.3.5 Compare Value High Register (ADCCVH) In 12-bit mode, the ADCCVH register holds the upper four bits of the 12-bit compare value. When the compare function is enabled, these bits are compared to the upper four bits of the result following a conversion in 12-bit mode. R 7 6 5 4 0 0 0 0 3 2 1 0 ADCV11 ADCV10 ADCV9 ADCV8 0 0 0 0 W Reset: 0 0 0 0 Figure 10-7. Compare Value High Register (ADCCVH) MC9S08DZ60 Series Data Sheet, Rev. 4 182 Freescale Semiconductor Chapter 10 Analog-to-Digital Converter (S08ADC12V1) In 10-bit mode, the ADCCVH register holds the upper two bits of the 10-bit compare value (ADCV[9:8]). These bits are compared to the upper two bits of the result following a conversion in 10-bit mode when the compare function is enabled. In 8-bit mode, ADCCVH is not used during compare. 10.3.6 Compare Value Low Register (ADCCVL) This register holds the lower 8 bits of the 12-bit or 10-bit compare value or all 8 bits of the 8-bit compare value. When the compare function is enabled, bits ADCV[7:0] are compared to the lower 8 bits of the result following a conversion in 12-bit, 10-bit or 8-bit mode. 7 6 5 4 3 2 1 0 ADCV7 ADCV6 ADCV5 ADCV4 ADCV3 ADCV2 ADCV1 ADCV0 0 0 0 0 0 0 0 0 R W Reset: Figure 10-8. Compare Value Low Register (ADCCVL) 10.3.7 Configuration Register (ADCCFG) ADCCFG selects the mode of operation, clock source, clock divide, and configures for low power and long sample time. 7 6 5 4 3 2 1 0 R ADLPC ADIV ADLSMP MODE ADICLK W Reset: 0 0 0 0 0 0 0 0 Figure 10-9. Configuration Register (ADCCFG) Table 10-6. ADCCFG Register Field Descriptions Field Description 7 ADLPC Low-Power Configuration. ADLPC controls the speed and power configuration of the successive approximation converter. This optimizes power consumption when higher sample rates are not required. 0 High speed configuration 1 Low power configuration: The power is reduced at the expense of maximum clock speed. 6:5 ADIV 4 ADLSMP Clock Divide Select. ADIV selects the divide ratio used by the ADC to generate the internal clock ADCK. Table 10-7 shows the available clock configurations. Long Sample Time Configuration. ADLSMP selects between long and short sample time. This adjusts the sample period to allow higher impedance inputs to be accurately sampled or to maximize conversion speed for lower impedance inputs. Longer sample times can also be used to lower overall power consumption when continuous conversions are enabled if high conversion rates are not required. 0 Short sample time 1 Long sample time MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 183 Chapter 10 Analog-to-Digital Converter (S08ADC12V1) Table 10-6. ADCCFG Register Field Descriptions (continued) Field Description 3:2 MODE Conversion Mode Selection. MODE bits are used to select between 12-, 10-, or 8-bit operation. See Table 10-8. 1:0 ADICLK Input Clock Select. ADICLK bits select the input clock source to generate the internal clock ADCK. See Table 10-9. Table 10-7. Clock Divide Select ADIV Divide Ratio Clock Rate 00 1 Input clock 01 2 Input clock / 2 10 4 Input clock / 4 11 8 Input clock / 8 Table 10-8. Conversion Modes MODE Mode Description 00 8-bit conversion (N=8) 01 12-bit conversion (N=12) 10 10-bit conversion (N=10) 11 Reserved Table 10-9. Input Clock Select ADICLK 10.3.8 Selected Clock Source 00 Bus clock 01 Bus clock divided by 2 10 Alternate clock (ALTCLK) 11 Asynchronous clock (ADACK) Pin Control 1 Register (APCTL1) The pin control registers disable the I/O port control of MCU pins used as analog inputs. APCTL1 is MC9S08DZ60 Series Data Sheet, Rev. 4 184 Freescale Semiconductor Chapter 10 Analog-to-Digital Converter (S08ADC12V1) used to control the pins associated with channels 0-7 of the ADC module. 7 6 5 4 3 2 1 0 ADPC7 ADPC6 ADPC5 ADPC4 ADPC3 ADPC2 ADPC1 ADPC0 0 0 0 0 0 0 0 0 R W Reset: Figure 10-10. Pin Control 1 Register (APCTL1) Table 10-10. APCTL1 Register Field Descriptions Field Description 7 ADPC7 ADC Pin Control 7. ADPC7 controls the pin associated with channel AD7. 0 AD7 pin I/O control enabled 1 AD7 pin I/O control disabled 6 ADPC6 ADC Pin Control 6. ADPC6 controls the pin associated with channel AD6. 0 AD6 pin I/O control enabled 1 AD6 pin I/O control disabled 5 ADPC5 ADC Pin Control 5. ADPC5 controls the pin associated with channel AD5. 0 AD5 pin I/O control enabled 1 AD5 pin I/O control disabled 4 ADPC4 ADC Pin Control 4. ADPC4 controls the pin associated with channel AD4. 0 AD4 pin I/O control enabled 1 AD4 pin I/O control disabled 3 ADPC3 ADC Pin Control 3. ADPC3 controls the pin associated with channel AD3. 0 AD3 pin I/O control enabled 1 AD3 pin I/O control disabled 2 ADPC2 ADC Pin Control 2. ADPC2 controls the pin associated with channel AD2. 0 AD2 pin I/O control enabled 1 AD2 pin I/O control disabled 1 ADPC1 ADC Pin Control 1. ADPC1 controls the pin associated with channel AD1. 0 AD1 pin I/O control enabled 1 AD1 pin I/O control disabled 0 ADPC0 ADC Pin Control 0. ADPC0 controls the pin associated with channel AD0. 0 AD0 pin I/O control enabled 1 AD0 pin I/O control disabled 10.3.9 Pin Control 2 Register (APCTL2) APCTL2 controls channels 8-15 of the ADC module. 7 6 5 4 3 2 1 0 ADPC15 ADPC14 ADPC13 ADPC12 ADPC11 ADPC10 ADPC9 ADPC8 0 0 0 0 0 0 0 0 R W Reset: Figure 10-11. Pin Control 2 Register (APCTL2) MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 185 Chapter 10 Analog-to-Digital Converter (S08ADC12V1) Table 10-11. APCTL2 Register Field Descriptions Field Description 7 ADPC15 ADC Pin Control 15. ADPC15 controls the pin associated with channel AD15. 0 AD15 pin I/O control enabled 1 AD15 pin I/O control disabled 6 ADPC14 ADC Pin Control 14. ADPC14 controls the pin associated with channel AD14. 0 AD14 pin I/O control enabled 1 AD14 pin I/O control disabled 5 ADPC13 ADC Pin Control 13. ADPC13 controls the pin associated with channel AD13. 0 AD13 pin I/O control enabled 1 AD13 pin I/O control disabled 4 ADPC12 ADC Pin Control 12. ADPC12 controls the pin associated with channel AD12. 0 AD12 pin I/O control enabled 1 AD12 pin I/O control disabled 3 ADPC11 ADC Pin Control 11. ADPC11 controls the pin associated with channel AD11. 0 AD11 pin I/O control enabled 1 AD11 pin I/O control disabled 2 ADPC10 ADC Pin Control 10. ADPC10 controls the pin associated with channel AD10. 0 AD10 pin I/O control enabled 1 AD10 pin I/O control disabled 1 ADPC9 ADC Pin Control 9. ADPC9 controls the pin associated with channel AD9. 0 AD9 pin I/O control enabled 1 AD9 pin I/O control disabled 0 ADPC8 ADC Pin Control 8. ADPC8 controls the pin associated with channel AD8. 0 AD8 pin I/O control enabled 1 AD8 pin I/O control disabled 10.3.10 Pin Control 3 Register (APCTL3) APCTL3 controls channels 16-23 of the ADC module. 7 6 5 4 3 2 1 0 ADPC23 ADPC22 ADPC21 ADPC20 ADPC19 ADPC18 ADPC17 ADPC16 0 0 0 0 0 0 0 0 R W Reset: Figure 10-12. Pin Control 3 Register (APCTL3) MC9S08DZ60 Series Data Sheet, Rev. 4 186 Freescale Semiconductor Chapter 10 Analog-to-Digital Converter (S08ADC12V1) Table 10-12. APCTL3 Register Field Descriptions Field Description 7 ADPC23 ADC Pin Control 23. ADPC23 controls the pin associated with channel AD23. 0 AD23 pin I/O control enabled 1 AD23 pin I/O control disabled 6 ADPC22 ADC Pin Control 22. ADPC22 controls the pin associated with channel AD22. 0 AD22 pin I/O control enabled 1 AD22 pin I/O control disabled 5 ADPC21 ADC Pin Control 21. ADPC21 controls the pin associated with channel AD21. 0 AD21 pin I/O control enabled 1 AD21 pin I/O control disabled 4 ADPC20 ADC Pin Control 20. ADPC20 controls the pin associated with channel AD20. 0 AD20 pin I/O control enabled 1 AD20 pin I/O control disabled 3 ADPC19 ADC Pin Control 19. ADPC19 controls the pin associated with channel AD19. 0 AD19 pin I/O control enabled 1 AD19 pin I/O control disabled 2 ADPC18 ADC Pin Control 18. ADPC18 controls the pin associated with channel AD18. 0 AD18 pin I/O control enabled 1 AD18 pin I/O control disabled 1 ADPC17 ADC Pin Control 17. ADPC17 controls the pin associated with channel AD17. 0 AD17 pin I/O control enabled 1 AD17 pin I/O control disabled 0 ADPC16 ADC Pin Control 16. ADPC16 controls the pin associated with channel AD16. 0 AD16 pin I/O control enabled 1 AD16 pin I/O control disabled 10.4 Functional Description The ADC module is disabled during reset or when the ADCH bits are all high. The module is idle when a conversion has completed and another conversion has not been initiated. When idle, the module is in its lowest power state. The ADC can perform an analog-to-digital conversion on any of the software selectable channels. In 12-bit and 10-bit mode, the selected channel voltage is converted by a successive approximation algorithm into a 12-bit digital result. In 8-bit mode, the selected channel voltage is converted by a successive approximation algorithm into a 9-bit digital result. When the conversion is completed, the result is placed in the data registers (ADCRH and ADCRL). In 10-bit mode, the result is rounded to 10 bits and placed in the data registers (ADCRH and ADCRL). In 8-bit mode, the result is rounded to 8 bits and placed in ADCRL. The conversion complete flag (COCO) is then set and an interrupt is generated if the conversion complete interrupt has been enabled (AIEN = 1). The ADC module has the capability of automatically comparing the result of a conversion with the contents of its compare registers. The compare function is enabled by setting the ACFE bit and operates with any of the conversion modes and configurations. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 187 Chapter 10 Analog-to-Digital Converter (S08ADC12V1) 10.4.1 Clock Select and Divide Control One of four clock sources can be selected as the clock source for the ADC module. This clock source is then divided by a configurable value to generate the input clock to the converter (ADCK). The clock is selected from one of the following sources by means of the ADICLK bits. * The bus clock, which is equal to the frequency at which software is executed. This is the default selection following reset. * The bus clock divided by two. For higher bus clock rates, this allows a maximum divide by 16 of the bus clock. * ALTCLK, as defined for this MCU (See module section introduction). * The asynchronous clock (ADACK). This clock is generated from a clock source within the ADC module. When selected as the clock source, this clock remains active while the MCU is in wait or stop3 mode and allows conversions in these modes for lower noise operation. Whichever clock is selected, its frequency must fall within the specified frequency range for ADCK. If the available clocks are too slow, the ADC do not perform according to specifications. If the available clocks are too fast, the clock must be divided to the appropriate frequency. This divider is specified by the ADIV bits and can be divide-by 1, 2, 4, or 8. 10.4.2 Input Select and Pin Control The pin control registers (APCTL3, APCTL2, and APCTL1) disable the I/O port control of the pins used as analog inputs.When a pin control register bit is set, the following conditions are forced for the associated MCU pin: * The output buffer is forced to its high impedance state. * The input buffer is disabled. A read of the I/O port returns a zero for any pin with its input buffer disabled. * The pullup is disabled. 10.4.3 Hardware Trigger The ADC module has a selectable asynchronous hardware conversion trigger, ADHWT, that is enabled when the ADTRG bit is set. This source is not available on all MCUs. Consult the module introduction for information on the ADHWT source specific to this MCU. When ADHWT source is available and hardware trigger is enabled (ADTRG=1), a conversion is initiated on the rising edge of ADHWT. If a conversion is in progress when a rising edge occurs, the rising edge is ignored. In continuous convert configuration, only the initial rising edge to launch continuous conversions is observed. The hardware trigger function operates in conjunction with any of the conversion modes and configurations. 10.4.4 Conversion Control Conversions can be performed in 12-bit mode, 10-bit mode, or 8-bit mode as determined by the MODE bits. Conversions can be initiated by a software or hardware trigger. In addition, the ADC module can be MC9S08DZ60 Series Data Sheet, Rev. 4 188 Freescale Semiconductor Chapter 10 Analog-to-Digital Converter (S08ADC12V1) configured for low power operation, long sample time, continuous conversion, and automatic compare of the conversion result to a software determined compare value. 10.4.4.1 Initiating Conversions A conversion is initiated: * Following a write to ADCSC1 (with ADCH bits not all 1s) if software triggered operation is selected. * Following a hardware trigger (ADHWT) event if hardware triggered operation is selected. * Following the transfer of the result to the data registers when continuous conversion is enabled. If continuous conversions are enabled, a new conversion is automatically initiated after the completion of the current conversion. In software triggered operation, continuous conversions begin after ADCSC1 is written and continue until aborted. In hardware triggered operation, continuous conversions begin after a hardware trigger event and continue until aborted. 10.4.4.2 Completing Conversions A conversion is completed when the result of the conversion is transferred into the data result registers, ADCRH and ADCRL. This is indicated by the setting of COCO. An interrupt is generated if AIEN is high at the time that COCO is set. A blocking mechanism prevents a new result from overwriting previous data in ADCRH and ADCRL if the previous data is in the process of being read while in 12-bit or 10-bit MODE (the ADCRH register has been read but the ADCRL register has not). When blocking is active, the data transfer is blocked, COCO is not set, and the new result is lost. In the case of single conversions with the compare function enabled and the compare condition false, blocking has no effect and ADC operation is terminated. In all other cases of operation, when a data transfer is blocked, another conversion is initiated regardless of the state of ADCO (single or continuous conversions enabled). If single conversions are enabled, the blocking mechanism could result in several discarded conversions and excess power consumption. To avoid this issue, the data registers must not be read after initiating a single conversion until the conversion completes. 10.4.4.3 Aborting Conversions Any conversion in progress is aborted when: * A write to ADCSC1 occurs (the current conversion will be aborted and a new conversion will be initiated, if ADCH are not all 1s). * A write to ADCSC2, ADCCFG, ADCCVH, or ADCCVL occurs. This indicates a mode of operation change has occurred and the current conversion is therefore invalid. * The MCU is reset. * The MCU enters stop mode with ADACK not enabled. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 189 Chapter 10 Analog-to-Digital Converter (S08ADC12V1) When a conversion is aborted, the contents of the data registers, ADCRH and ADCRL, are not altered. However, they continue to be the values transferred after the completion of the last successful conversion. If the conversion was aborted by a reset, ADCRH and ADCRL return to their reset states. 10.4.4.4 Power Control The ADC module remains in its idle state until a conversion is initiated. If ADACK is selected as the conversion clock source, the ADACK clock generator is also enabled. Power consumption when active can be reduced by setting ADLPC. This results in a lower maximum value for fADCK (see the electrical specifications). 10.4.4.5 Sample Time and Total Conversion Time The total conversion time depends on the sample time (as determined by ADLSMP), the MCU bus frequency, the conversion mode (8-bit, 10-bit or 12-bit), and the frequency of the conversion clock (fADCK). After the module becomes active, sampling of the input begins. ADLSMP selects between short (3.5 ADCK cycles) and long (23.5 ADCK cycles) sample times.When sampling is complete, the converter is isolated from the input channel and a successive approximation algorithm is performed to determine the digital value of the analog signal. The result of the conversion is transferred to ADCRH and ADCRL upon completion of the conversion algorithm. If the bus frequency is less than the fADCK frequency, precise sample time for continuous conversions cannot be guaranteed when short sample is enabled (ADLSMP=0). If the bus frequency is less than 1/11th of the fADCK frequency, precise sample time for continuous conversions cannot be guaranteed when long sample is enabled (ADLSMP=1). The maximum total conversion time for different conditions is summarized in Table 10-13. Table 10-13. Total Conversion Time vs. Control Conditions Conversion Type ADICLK ADLSMP Max Total Conversion Time Single or first continuous 8-bit 0x, 10 0 20 ADCK cycles + 5 bus clock cycles Single or first continuous 10-bit or 12-bit 0x, 10 0 23 ADCK cycles + 5 bus clock cycles Single or first continuous 8-bit 0x, 10 1 40 ADCK cycles + 5 bus clock cycles Single or first continuous 10-bit or 12-bit 0x, 10 1 43 ADCK cycles + 5 bus clock cycles Single or first continuous 8-bit 11 0 5 s + 20 ADCK + 5 bus clock cycles Single or first continuous 10-bit or 12-bit 11 0 5 s + 23 ADCK + 5 bus clock cycles Single or first continuous 8-bit 11 1 5 s + 40 ADCK + 5 bus clock cycles Single or first continuous 10-bit or 12-bit 11 1 5 s + 43 ADCK + 5 bus clock cycles Subsequent continuous 8-bit; fBUS > fADCK xx 0 17 ADCK cycles Subsequent continuous 10-bit or 12-bit; fBUS > fADCK xx 0 20 ADCK cycles Subsequent continuous 8-bit; fBUS > fADCK/11 xx 1 37 ADCK cycles MC9S08DZ60 Series Data Sheet, Rev. 4 190 Freescale Semiconductor Chapter 10 Analog-to-Digital Converter (S08ADC12V1) Table 10-13. Total Conversion Time vs. Control Conditions Conversion Type ADICLK ADLSMP Max Total Conversion Time Subsequent continuous 10-bit or 12-bit; fBUS > fADCK/11 xx 1 40 ADCK cycles The maximum total conversion time is determined by the clock source chosen and the divide ratio selected. The clock source is selectable by the ADICLK bits, and the divide ratio is specified by the ADIV bits. For example, in 10-bit mode, with the bus clock selected as the input clock source, the input clock divide-by-1 ratio selected, and a bus frequency of 8 MHz, then the conversion time for a single conversion is: Conversion time = 23 ADCK Cyc 8 MHz/1 + 5 bus Cyc 8 MHz = 3.5 ms Number of bus cycles = 3.5 ms x 8 MHz = 28 cycles NOTE The ADCK frequency must be between fADCK minimum and fADCK maximum to meet ADC specifications. 10.4.5 Automatic Compare Function The compare function can be configured to check for an upper or lower limit. After the input is sampled and converted, the result is added to the two's complement of the compare value (ADCCVH and ADCCVL). When comparing to an upper limit (ACFGT = 1), if the result is greater-than or equal-to the compare value, COCO is set. When comparing to a lower limit (ACFGT = 0), if the result is less than the compare value, COCO is set. The value generated by the addition of the conversion result and the two's complement of the compare value is transferred to ADCRH and ADCRL. Upon completion of a conversion while the compare function is enabled, if the compare condition is not true, COCO is not set and no data is transferred to the result registers. An ADC interrupt is generated upon the setting of COCO if the ADC interrupt is enabled (AIEN = 1). NOTE The compare function can monitor the voltage on a channel while the MCU is in wait or stop3 mode. The ADC interrupt wakes the MCU when the compare condition is met. 10.4.6 MCU Wait Mode Operation Wait mode is a lower power-consumption standby mode from which recovery is fast because the clock sources remain active. If a conversion is in progress when the MCU enters wait mode, it continues until completion. Conversions can be initiated while the MCU is in wait mode by means of the hardware trigger or if continuous conversions are enabled. The bus clock, bus clock divided by two, and ADACK are available as conversion clock sources while in wait mode. The use of ALTCLK as the conversion clock source in wait is dependent on the definition of MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 191 Chapter 10 Analog-to-Digital Converter (S08ADC12V1) ALTCLK for this MCU. Consult the module introduction for information on ALTCLK specific to this MCU. A conversion complete event sets the COCO and generates an ADC interrupt to wake the MCU from wait mode if the ADC interrupt is enabled (AIEN = 1). 10.4.7 MCU Stop3 Mode Operation Stop mode is a low power-consumption standby mode during which most or all clock sources on the MCU are disabled. 10.4.7.1 Stop3 Mode With ADACK Disabled If the asynchronous clock, ADACK, is not selected as the conversion clock, executing a stop instruction aborts the current conversion and places the ADC in its idle state. The contents of ADCRH and ADCRL are unaffected by stop3 mode. After exiting from stop3 mode, a software or hardware trigger is required to resume conversions. 10.4.7.2 Stop3 Mode With ADACK Enabled If ADACK is selected as the conversion clock, the ADC continues operation during stop3 mode. For guaranteed ADC operation, the MCU's voltage regulator must remain active during stop3 mode. Consult the module introduction for configuration information for this MCU. If a conversion is in progress when the MCU enters stop3 mode, it continues until completion. Conversions can be initiated while the MCU is in stop3 mode by means of the hardware trigger or if continuous conversions are enabled. A conversion complete event sets the COCO and generates an ADC interrupt to wake the MCU from stop3 mode if the ADC interrupt is enabled (AIEN = 1). NOTE The ADC module can wake the system from low-power stop and cause the MCU to begin consuming run-level currents without generating a system level interrupt. To prevent this scenario, software should ensure the data transfer blocking mechanism (discussed in Section 10.4.4.2, "Completing Conversions) is cleared when entering stop3 and continuing ADC conversions. 10.4.8 MCU Stop2 Mode Operation The ADC module is automatically disabled when the MCU enters stop2 mode. All module registers contain their reset values following exit from stop2. Therefore, the module must be re-enabled and re-configured following exit from stop2. MC9S08DZ60 Series Data Sheet, Rev. 4 192 Freescale Semiconductor Chapter 10 Analog-to-Digital Converter (S08ADC12V1) 10.5 Initialization Information This section gives an example that provides some basic direction on how to initialize and configure the ADC module. You can configure the module for 8-, 10-, or 12-bit resolution, single or continuous conversion, and a polled or interrupt approach, among many other options. Refer to Table 10-7, Table 10-8, and Table 10-9 for information used in this example. NOTE Hexadecimal values designated by a preceding 0x, binary values designated by a preceding %, and decimal values have no preceding character. 10.5.1 ADC Module Initialization Example 10.5.1.1 Initialization Sequence Before the ADC module can be used to complete conversions, an initialization procedure must be performed. A typical sequence is as follows: 1. Update the configuration register (ADCCFG) to select the input clock source and the divide ratio used to generate the internal clock, ADCK. This register is also used for selecting sample time and low-power configuration. 2. Update status and control register 2 (ADCSC2) to select the conversion trigger (hardware or software) and compare function options, if enabled. 3. Update status and control register 1 (ADCSC1) to select whether conversions will be continuous or completed only once, and to enable or disable conversion complete interrupts. The input channel on which conversions will be performed is also selected here. 10.5.1.2 Pseudo-Code Example In this example, the ADC module is set up with interrupts enabled to perform a single 10-bit conversion at low power with a long sample time on input channel 1, where the internal ADCK clock is derived from the bus clock divided by 1. ADCCFG = 0x98 (%10011000) Bit Bit Bit Bit Bit 7 6:5 4 3:2 1:0 ADLPC ADIV ADLSMP MODE ADICLK 1 00 1 10 00 Configures for low power (lowers maximum clock speed) Sets the ADCK to the input clock / 1 Configures for long sample time Sets mode at 10-bit conversions Selects bus clock as input clock source ADCSC2 = 0x00 (%00000000) Bit Bit Bit Bit Bit Bit 7 6 5 4 3:2 1:0 ADACT ADTRG ACFE ACFGT 0 0 0 0 00 00 Flag indicates if a conversion is in progress Software trigger selected Compare function disabled Not used in this example Reserved, always reads zero Reserved for Freescale's internal use; always write zero MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 193 Chapter 10 Analog-to-Digital Converter (S08ADC12V1) ADCSC1 = 0x41 (%01000001) Bit Bit Bit Bit 7 6 5 4:0 COCO AIEN ADCO ADCH 0 1 0 00001 Read-only flag which is set when a conversion completes Conversion complete interrupt enabled One conversion only (continuous conversions disabled) Input channel 1 selected as ADC input channel ADCRH/L = 0xxx Holds results of conversion. Read high byte (ADCRH) before low byte (ADCRL) so that conversion data cannot be overwritten with data from the next conversion. ADCCVH/L = 0xxx Holds compare value when compare function enabled APCTL1=0x02 AD1 pin I/O control disabled. All other AD pins remain general purpose I/O pins APCTL2=0x00 All other AD pins remain general purpose I/O pins Reset Initialize ADC ADCCFG = 0x98 ADCSC2 = 0x00 ADCSC1 = 0x41 Check COCO=1? No Yes Read ADCRH Then ADCRL To Clear COCO Bit Continue Figure 10-13. Initialization Flowchart for Example MC9S08DZ60 Series Data Sheet, Rev. 4 194 Freescale Semiconductor Chapter 10 Analog-to-Digital Converter (S08ADC12V1) 10.6 Application Information This section contains information for using the ADC module in applications. The ADC has been designed to be integrated into a microcontroller for use in embedded control applications requiring an A/D converter. 10.6.1 External Pins and Routing The following sections discuss the external pins associated with the ADC module and how they should be used for best results. 10.6.1.1 Analog Supply Pins The ADC module has analog power and ground supplies (VDDAD and VSSAD) available as separate pins on some devices. VSSAD is shared on the same pin as the MCU digital VSS on some devices. On other devices, VSSAD and VDDAD are shared with the MCU digital supply pins. In these cases, there are separate pads for the analog supplies bonded to the same pin as the corresponding digital supply so that some degree of isolation between the supplies is maintained. When available on a separate pin, both VDDAD and VSSAD must be connected to the same voltage potential as their corresponding MCU digital supply (VDD and VSS) and must be routed carefully for maximum noise immunity and bypass capacitors placed as near as possible to the package. If separate power supplies are used for analog and digital power, the ground connection between these supplies must be at the VSSAD pin. This should be the only ground connection between these supplies if possible. The VSSAD pin makes a good single point ground location. 10.6.1.2 Analog Reference Pins In addition to the analog supplies, the ADC module has connections for two reference voltage inputs. The high reference is VREFH, which may be shared on the same pin as VDDAD on some devices. The low reference is VREFL, which may be shared on the same pin as VSSAD on some devices. When available on a separate pin, VREFH may be connected to the same potential as VDDAD, or may be driven by an external source between the minimum VDDAD spec and the VDDAD potential (VREFH must never exceed VDDAD). When available on a separate pin, VREFL must be connected to the same voltage potential as VSSAD. VREFH and VREFL must be routed carefully for maximum noise immunity and bypass capacitors placed as near as possible to the package. AC current in the form of current spikes required to supply charge to the capacitor array at each successive approximation step is drawn through the VREFH and VREFL loop. The best external component to meet this current demand is a 0.1 F capacitor with good high frequency characteristics. This capacitor is connected between VREFH and VREFL and must be placed as near as possible to the package pins. Resistance in the path is not recommended because the current causes a voltage drop that could result in conversion errors. Inductance in this path must be minimum (parasitic only). MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 195 Chapter 10 Analog-to-Digital Converter (S08ADC12V1) 10.6.1.3 Analog Input Pins The external analog inputs are typically shared with digital I/O pins on MCU devices. The pin I/O control is disabled by setting the appropriate control bit in one of the pin control registers. Conversions can be performed on inputs without the associated pin control register bit set. It is recommended that the pin control register bit always be set when using a pin as an analog input. This avoids problems with contention because the output buffer is in its high impedance state and the pullup is disabled. Also, the input buffer draws DC current when its input is not at VDD or VSS. Setting the pin control register bits for all pins used as analog inputs should be done to achieve lowest operating current. Empirical data shows that capacitors on the analog inputs improve performance in the presence of noise or when the source impedance is high. Use of 0.01 F capacitors with good high-frequency characteristics is sufficient. These capacitors are not necessary in all cases, but when used they must be placed as near as possible to the package pins and be referenced to VSSA. For proper conversion, the input voltage must fall between VREFH and VREFL. If the input is equal to or exceeds VREFH, the converter circuit converts the signal to 0xFFF (full scale 12-bit representation), 0x3FF (full scale 10-bit representation) or 0xFF (full scale 8-bit representation). If the input is equal to or less than VREFL, the converter circuit converts it to 0x000. Input voltages between VREFH and VREFL are straight-line linear conversions. There is a brief current associated with VREFL when the sampling capacitor is charging. The input is sampled for 3.5 cycles of the ADCK source when ADLSMP is low, or 23.5 cycles when ADLSMP is high. For minimal loss of accuracy due to current injection, pins adjacent to the analog input pins should not be transitioning during conversions. 10.6.2 Sources of Error Several sources of error exist for A/D conversions. These are discussed in the following sections. 10.6.2.1 Sampling Error For proper conversions, the input must be sampled long enough to achieve the proper accuracy. Given the maximum input resistance of approximately 7k and input capacitance of approximately 5.5 pF, sampling to within 1/4LSB (at 12-bit resolution) can be achieved within the minimum sample window (3.5 cycles @ 8 MHz maximum ADCK frequency) provided the resistance of the external analog source (RAS) is kept below 2 k. Higher source resistances or higher-accuracy sampling is possible by setting ADLSMP (to increase the sample window to 23.5 cycles) or decreasing ADCK frequency to increase sample time. 10.6.2.2 Pin Leakage Error Leakage on the I/O pins can cause conversion error if the external analog source resistance (RAS) is high. If this error cannot be tolerated by the application, keep RAS lower than VDDAD / (2N*ILEAK) for less than 1/4LSB leakage error (N = 8 in 8-bit, 10 in 10-bit or 12 in 12-bit mode). MC9S08DZ60 Series Data Sheet, Rev. 4 196 Freescale Semiconductor Chapter 10 Analog-to-Digital Converter (S08ADC12V1) 10.6.2.3 Noise-Induced Errors System noise that occurs during the sample or conversion process can affect the accuracy of the conversion. The ADC accuracy numbers are guaranteed as specified only if the following conditions are met: * There is a 0.1 F low-ESR capacitor from VREFH to VREFL. * There is a 0.1 F low-ESR capacitor from VDDAD to VSSAD. * If inductive isolation is used from the primary supply, an additional 1 F capacitor is placed from VDDAD to VSSAD. * VSSAD (and VREFL, if connected) is connected to VSS at a quiet point in the ground plane. * Operate the MCU in wait or stop3 mode before initiating (hardware triggered conversions) or immediately after initiating (hardware or software triggered conversions) the ADC conversion. -- For software triggered conversions, immediately follow the write to ADCSC1 with a wait instruction or stop instruction. -- For stop3 mode operation, select ADACK as the clock source. Operation in stop3 reduces VDD noise but increases effective conversion time due to stop recovery. * There is no I/O switching, input or output, on the MCU during the conversion. There are some situations where external system activity causes radiated or conducted noise emissions or excessive VDD noise is coupled into the ADC. In these situations, or when the MCU cannot be placed in wait or stop3 or I/O activity cannot be halted, these recommended actions may reduce the effect of noise on the accuracy: * Place a 0.01 F capacitor (CAS) on the selected input channel to VREFL or VSSAD (this improves noise issues, but affects the sample rate based on the external analog source resistance). * Average the result by converting the analog input many times in succession and dividing the sum of the results. Four samples are required to eliminate the effect of a 1LSB, one-time error. * Reduce the effect of synchronous noise by operating off the asynchronous clock (ADACK) and averaging. Noise that is synchronous to ADCK cannot be averaged out. 10.6.2.4 Code Width and Quantization Error The ADC quantizes the ideal straight-line transfer function into 4096 steps (in 12-bit mode). Each step ideally has the same height (1 code) and width. The width is defined as the delta between the transition points to one code and the next. The ideal code width for an N bit converter (in this case N can be 8, 10 or 12), defined as 1LSB, is: 1 lsb = (VREFH - VREFL) / 2N Eqn. 10-2 There is an inherent quantization error due to the digitization of the result. For 8-bit or 10-bit conversions the code transitions when the voltage is at the midpoint between the points where the straight line transfer function is exactly represented by the actual transfer function. Therefore, the quantization error will be 1/2 lsb in 8- or 10-bit mode. As a consequence, however, the code width of the first (0x000) conversion is only 1/2 lsb and the code width of the last (0xFF or 0x3FF) is 1.5 lsb. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 197 Chapter 10 Analog-to-Digital Converter (S08ADC12V1) For 12-bit conversions the code transitions only after the full code width is present, so the quantization error is -1 lsb to 0 lsb and the code width of each step is 1 lsb. 10.6.2.5 Linearity Errors The ADC may also exhibit non-linearity of several forms. Every effort has been made to reduce these errors but the system should be aware of them because they affect overall accuracy. These errors are: * Zero-scale error (EZS) (sometimes called offset) -- This error is defined as the difference between the actual code width of the first conversion and the ideal code width (1/2 lsb in 8-bit or 10-bit modes and 1 lsb in 12-bit mode). If the first conversion is 0x001, the difference between the actual 0x001 code width and its ideal (1 lsb) is used. * Full-scale error (EFS) -- This error is defined as the difference between the actual code width of the last conversion and the ideal code width (1.5 lsb in 8-bit or 10-bit modes and 1LSB in 12-bit mode). If the last conversion is 0x3FE, the difference between the actual 0x3FE code width and its ideal (1LSB) is used. * Differential non-linearity (DNL) -- This error is defined as the worst-case difference between the actual code width and the ideal code width for all conversions. * Integral non-linearity (INL) -- This error is defined as the highest-value the (absolute value of the) running sum of DNL achieves. More simply, this is the worst-case difference of the actual transition voltage to a given code and its corresponding ideal transition voltage, for all codes. * Total unadjusted error (TUE) -- This error is defined as the difference between the actual transfer function and the ideal straight-line transfer function and includes all forms of error. 10.6.2.6 Code Jitter, Non-Monotonicity, and Missing Codes Analog-to-digital converters are susceptible to three special forms of error. These are code jitter, non-monotonicity, and missing codes. Code jitter is when, at certain points, a given input voltage converts to one of two values when sampled repeatedly. Ideally, when the input voltage is infinitesimally smaller than the transition voltage, the converter yields the lower code (and vice-versa). However, even small amounts of system noise can cause the converter to be indeterminate (between two codes) for a range of input voltages around the transition voltage. This range is normally around 1/2lsb in 8-bit or 10-bit mode, or around 2 lsb in 12-bit mode, and increases with noise. This error may be reduced by repeatedly sampling the input and averaging the result. Additionally the techniques discussed in Section 10.6.2.3 reduces this error. Non-monotonicity is defined as when, except for code jitter, the converter converts to a lower code for a higher input voltage. Missing codes are those values never converted for any input value. In 8-bit or 10-bit mode, the ADC is guaranteed to be monotonic and have no missing codes. MC9S08DZ60 Series Data Sheet, Rev. 4 198 Freescale Semiconductor Chapter 11 Inter-Integrated Circuit (S08IICV2) 11.1 Introduction The inter-integrated circuit (IIC) provides a method of communication between a number of devices. The interface is designed to operate up to 100 kbps with maximum bus loading and timing. The device is capable of operating at higher baud rates, up to a maximum of clock/20, with reduced bus loading. The maximum communication length and the number of devices that can be connected are limited by a maximum bus capacitance of 400 pF. All MC9S08DZ60 Series MCUs feature the IIC, as shown in the following block diagram. NOTE Drive strength must be disabled (DSE=0) for the IIC pins when using the IIC module for correct operation. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 199 PORT A PTA7/PIA7/ADP7/IRQ PTA6/PIA6/ADP6 PTA5/PIA5/ADP5 PTA4/PIA4/ADP4 PTA3/PIA3/ADP3/ACMP1O PTA2/PIA2/ADP2/ACMP1PTA1/PIA1/ADP1/ACMP1+ PTA0/PIA0/ADP0/MCLK PORT B PTB7/PIB7/ADP15 PTB6/PIB6/ADP14 PTB5/PIB5/ADP13 PTB4/PIB4/ADP12 PTB3/PIB3/ADP11 PTB2/PIB2/ADP10 PTB1/PIB1/ADP9 PTB0/PIB0/ADP8 PORT C PTC7/ADP23 PTC6/ADP22 PTC5/ADP21 PTC4/ADP20 PTC3/ADP19 PTC2/ADP18 PTC1/ADP17 PTC0/ADP16 PORT D PTD7/PID7/TPM1CH5 PTD6/PID6/TPM1CH4 PTD5/PID5/TPM1CH3 PTD4/PID4/TPM1CH2 PTD3/PID3/TPM1CH1 PTD2/PID2/TPM1CH0 PTD1/PID1/TPM2CH1 PTD0/PID0/TPM2CH0 PORT E PTE7/RxD2/RXCAN PTE6/TxD2/TXCAN PTE5/SDA/MISO PTE4/SCL/MOSI PTE3/SPSCK PTE2/SS PTE1/RxD1 PTE0/TxD1 PORT F PTF7 PTF6/ACMP2O PTF5/ACMP2PTF4/ACMP2+ PTF3/TPM2CLK/SDA PTF2/TPM1CLK/SCL PTF1/RxD2 PTF0/TxD2 PORT G Chapter 11 Inter-Integrated Circuit (S08IICV2) PTG5 PTG4 PTG3 PTG2 PTG1/XTAL PTG0/EXTAL HCS08 CORE CPU BKGD/MS BDC ANALOG COMPARATOR (ACMP1) BKP ACMP1O ACMP1ACMP1+ HCS08 SYSTEM CONTROL RESETS AND INTERRUPTS MODES OF OPERATION POWER MANAGEMENT COP LVD INT IRQ ADP7-ADP0 24-CHANNEL,12-BIT ANALOG-TO-DIGITAL CONVERTER (ADC) VREFH VREFL VDDA VSSA USER FLASH MC9S0DZ60 = 60K MC9S0DZ48 = 48K MC9S0DZ32 = 32K MC9S0DZ16 = 16K USER EEPROM MC9S0DZ60 = 2K TPM1CH5 TPM1CH0 6 TPM1CLK 2-CHANNEL TIMER/PWM MODULE (TPM2) TPM2CH1, TPM2CH0 TPM2CLK CONTROLLER AREA NETWORK (MSCAN) SERIAL PERIPHERAL INTERFACE MODULE (SPI) DEBUG MODULE (DBG) SERIAL COMMUNICATIONS INTERFACE (SCI1) VOLTAGE REGULATOR ADP15-ADP8 ADP23-ADP16 6-CHANNEL TIMER/PWM MODULE (TPM1) USER RAM MC9S0DZ60 = 4K REAL-TIME COUNTER (RTC) VDD VDD VSS VSS 8 IRQ RESET ANALOG COMPARATOR (ACMP2) IIC MODULE (IIC) SERIAL COMMUNICATIONS INTERFACE (SCI2) RxCAN TxCAN MISO MOSI SPSCK SS RxD1 TxD1 ACMP2O ACMP2ACMP2+ SDA SCL RxD2 TxD2 MULTI-PURPOSE CLOCK GENERATOR (MCG) XTAL EXTAL OSCILLATOR (XOSC) - VREFH/VREFL internally connected to VDDA/VSSA in 48-pin and 32-pin packages - VDD and VSS pins are each internally connected to two pads in 32-pin package - Pin not connected in 48-pin and 32-pin packages - Pin not connected in 32-pin package Figure 11-1. MC9S08DZ60 Block Diagram MC9S08DZ60 Series Data Sheet, Rev. 4 200 Freescale Semiconductor Chapter 11 Inter-Integrated Circuit (S08IICV2) 11.1.1 Features The IIC includes these distinctive features: * Compatible with IIC bus standard * Multi-master operation * Software programmable for one of 64 different serial clock frequencies * Software selectable acknowledge bit * Interrupt driven byte-by-byte data transfer * Arbitration lost interrupt with automatic mode switching from master to slave * Calling address identification interrupt * Start and stop signal generation/detection * Repeated start signal generation * Acknowledge bit generation/detection * Bus busy detection * General call recognition * 10-bit address extension 11.1.2 Modes of Operation A brief description of the IIC in the various MCU modes is given here. * Run mode -- This is the basic mode of operation. To conserve power in this mode, disable the module. * Wait mode -- The module continues to operate while the MCU is in wait mode and can provide a wake-up interrupt. * Stop mode -- The IIC is inactive in stop3 mode for reduced power consumption. The stop instruction does not affect IIC register states. Stop2 resets the register contents. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 201 Chapter 11 Inter-Integrated Circuit (S08IICV2) 11.1.3 Block Diagram Figure 11-2 is a block diagram of the IIC. Address Data Bus Interrupt ADDR_DECODE CTRL_REG DATA_MUX FREQ_REG ADDR_REG STATUS_REG DATA_REG Input Sync Start Stop Arbitration Control Clock Control In/Out Data Shift Register Address Compare SCL SDA Figure 11-2. IIC Functional Block Diagram 11.2 External Signal Description This section describes each user-accessible pin signal. 11.2.1 SCL -- Serial Clock Line The bidirectional SCL is the serial clock line of the IIC system. 11.2.2 SDA -- Serial Data Line The bidirectional SDA is the serial data line of the IIC system. 11.3 Register Definition This section consists of the IIC register descriptions in address order. MC9S08DZ60 Series Data Sheet, Rev. 4 202 Freescale Semiconductor Chapter 11 Inter-Integrated Circuit (S08IICV2) Refer to the direct-page register summary in the memory chapter of this document for the absolute address assignments for all IIC registers. This section refers to registers and control bits only by their names. A Freescale-provided equate or header file is used to translate these names into the appropriate absolute addresses. 11.3.1 IIC Address Register (IICA) 7 6 5 4 3 2 1 AD7 AD6 AD5 AD4 AD3 AD2 AD1 0 0 0 0 0 0 0 R 0 0 W Reset 0 = Unimplemented or Reserved Figure 11-3. IIC Address Register (IICA) Table 11-1. IICA Field Descriptions Field Description 7-1 AD[7:1] Slave Address. The AD[7:1] field contains the slave address to be used by the IIC module. This field is used on the 7-bit address scheme and the lower seven bits of the 10-bit address scheme. 11.3.2 IIC Frequency Divider Register (IICF) 7 6 5 4 3 2 1 0 0 0 0 R MULT ICR W Reset 0 0 0 0 0 Figure 11-4. IIC Frequency Divider Register (IICF) MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 203 Chapter 11 Inter-Integrated Circuit (S08IICV2) Table 11-2. IICF Field Descriptions Field 7-6 MULT 5-0 ICR Description IIC Multiplier Factor. The MULT bits define the multiplier factor, mul. This factor, along with the SCL divider, generates the IIC baud rate. The multiplier factor mul as defined by the MULT bits is provided below. 00 mul = 01 01 mul = 02 10 mul = 04 11 Reserved IIC Clock Rate. The ICR bits are used to prescale the bus clock for bit rate selection. These bits and the MULT bits determine the IIC baud rate, the SDA hold time, the SCL Start hold time, and the SCL Stop hold time. Table 11-4 provides the SCL divider and hold values for corresponding values of the ICR. The SCL divider multiplied by multiplier factor mul generates IIC baud rate. bus speed (Hz) IIC baud rate = --------------------------------------------mul x SCLdivider Eqn. 11-1 SDA hold time is the delay from the falling edge of SCL (IIC clock) to the changing of SDA (IIC data). SDA hold time = bus period (s) x mul x SDA hold value Eqn. 11-2 SCL start hold time is the delay from the falling edge of SDA (IIC data) while SCL is high (Start condition) to the falling edge of SCL (IIC clock). SCL Start hold time = bus period (s) x mul x SCL Start hold value Eqn. 11-3 SCL stop hold time is the delay from the rising edge of SCL (IIC clock) to the rising edge of SDA SDA (IIC data) while SCL is high (Stop condition). SCL Stop hold time = bus period (s) x mul x SCL Stop hold value Eqn. 11-4 For example, if the bus speed is 8 MHz, the table below shows the possible hold time values with different ICR and MULT selections to achieve an IIC baud rate of 100kbps. Table 11-3. Hold Time Values for 8 MHz Bus Speed Hold Times (s) MULT ICR SDA SCL Start SCL Stop 0x2 0x00 3.500 3.000 5.500 0x1 0x07 2.500 4.000 5.250 0x1 0x0B 2.250 4.000 5.250 0x0 0x14 2.125 4.250 5.125 0x0 0x18 1.125 4.750 5.125 MC9S08DZ60 Series Data Sheet, Rev. 4 204 Freescale Semiconductor Chapter 11 Inter-Integrated Circuit (S08IICV2) Table 11-4. IIC Divider and Hold Values ICR (hex) SCL Divider SDA Hold Value SCL Hold (Start) Value SDA Hold (Stop) Value ICR (hex) SCL Divider SDA Hold Value SCL Hold (Start) Value SCL Hold (Stop) Value 00 20 7 6 11 20 160 17 78 81 01 22 7 7 12 21 192 17 94 97 02 24 8 8 13 22 224 33 110 113 03 26 8 9 14 23 256 33 126 129 04 28 9 10 15 24 288 49 142 145 05 30 9 11 16 25 320 49 158 161 06 34 10 13 18 26 384 65 190 193 07 40 10 16 21 27 480 65 238 241 08 28 7 10 15 28 320 33 158 161 09 32 7 12 17 29 384 33 190 193 0A 36 9 14 19 2A 448 65 222 225 0B 40 9 16 21 2B 512 65 254 257 0C 44 11 18 23 2C 576 97 286 289 0D 48 11 20 25 2D 640 97 318 321 0E 56 13 24 29 2E 768 129 382 385 0F 68 13 30 35 2F 960 129 478 481 10 48 9 18 25 30 640 65 318 321 11 56 9 22 29 31 768 65 382 385 12 64 13 26 33 32 896 129 446 449 13 72 13 30 37 33 1024 129 510 513 14 80 17 34 41 34 1152 193 574 577 15 88 17 38 45 35 1280 193 638 641 16 104 21 46 53 36 1536 257 766 769 17 128 21 58 65 37 1920 257 958 961 18 80 9 38 41 38 1280 129 638 641 19 96 9 46 49 39 1536 129 766 769 1A 112 17 54 57 3A 1792 257 894 897 1B 128 17 62 65 3B 2048 257 1022 1025 1C 144 25 70 73 3C 2304 385 1150 1153 1D 160 25 78 81 3D 2560 385 1278 1281 1E 192 33 94 97 3E 3072 513 1534 1537 1F 240 33 118 121 3F 3840 513 1918 1921 MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 205 Chapter 11 Inter-Integrated Circuit (S08IICV2) 11.3.3 IIC Control Register (IICC1) 7 6 5 4 3 IICEN IICIE MST TX TXAK R W Reset 2 1 0 0 0 0 0 0 RSTA 0 0 0 0 0 0 = Unimplemented or Reserved Figure 11-5. IIC Control Register (IICC1) Table 11-5. IICC1 Field Descriptions Field Description 7 IICEN IIC Enable. The IICEN bit determines whether the IIC module is enabled. 0 IIC is not enabled 1 IIC is enabled 6 IICIE IIC Interrupt Enable. The IICIE bit determines whether an IIC interrupt is requested. 0 IIC interrupt request not enabled 1 IIC interrupt request enabled 5 MST Master Mode Select. The MST bit changes from a 0 to a 1 when a start signal is generated on the bus and master mode is selected. When this bit changes from a 1 to a 0 a stop signal is generated and the mode of operation changes from master to slave. 0 Slave mode 1 Master mode 4 TX Transmit Mode Select. The TX bit selects the direction of master and slave transfers. In master mode, this bit should be set according to the type of transfer required. Therefore, for address cycles, this bit is always high. When addressed as a slave, this bit should be set by software according to the SRW bit in the status register. 0 Receive 1 Transmit 3 TXAK Transmit Acknowledge Enable. This bit specifies the value driven onto the SDA during data acknowledge cycles for master and slave receivers. 0 An acknowledge signal is sent out to the bus after receiving one data byte 1 No acknowledge signal response is sent 2 RSTA Repeat start. Writing a 1 to this bit generates a repeated start condition provided it is the current master. This bit is always read as cleared. Attempting a repeat at the wrong time results in loss of arbitration. MC9S08DZ60 Series Data Sheet, Rev. 4 206 Freescale Semiconductor Chapter 11 Inter-Integrated Circuit (S08IICV2) 11.3.4 IIC Status Register (IICS) 7 R 6 TCF 5 4 BUSY IAAS 3 2 0 SRW ARBL 1 0 RXAK IICIF W Reset 1 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 11-6. IIC Status Register (IICS) Table 11-6. IICS Field Descriptions Field Description 7 TCF Transfer Complete Flag. This bit is set on the completion of a byte transfer. This bit is only valid during or immediately following a transfer to the IIC module or from the IIC module.The TCF bit is cleared by reading the IICD register in receive mode or writing to the IICD in transmit mode. 0 Transfer in progress 1 Transfer complete 6 IAAS Addressed as a Slave. The IAAS bit is set when the calling address matches the programmed slave address or when the GCAEN bit is set and a general call is received. Writing the IICC register clears this bit. 0 Not addressed 1 Addressed as a slave 5 BUSY Bus Busy. The BUSY bit indicates the status of the bus regardless of slave or master mode. The BUSY bit is set when a start signal is detected and cleared when a stop signal is detected. 0 Bus is idle 1 Bus is busy 4 ARBL Arbitration Lost. This bit is set by hardware when the arbitration procedure is lost. The ARBL bit must be cleared by software by writing a 1 to it. 0 Standard bus operation 1 Loss of arbitration 2 SRW Slave Read/Write. When addressed as a slave, the SRW bit indicates the value of the R/W command bit of the calling address sent to the master. 0 Slave receive, master writing to slave 1 Slave transmit, master reading from slave 1 IICIF IIC Interrupt Flag. The IICIF bit is set when an interrupt is pending. This bit must be cleared by software, by writing a 1 to it in the interrupt routine. One of the following events can set the IICIF bit: * One byte transfer completes * Match of slave address to calling address * Arbitration lost 0 No interrupt pending 1 Interrupt pending 0 RXAK Receive Acknowledge. When the RXAK bit is low, it indicates an acknowledge signal has been received after the completion of one byte of data transmission on the bus. If the RXAK bit is high it means that no acknowledge signal is detected. 0 Acknowledge received 1 No acknowledge received MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 207 Chapter 11 Inter-Integrated Circuit (S08IICV2) 11.3.5 IIC Data I/O Register (IICD) 7 6 5 4 3 2 1 0 0 0 0 0 R DATA W Reset 0 0 0 0 Figure 11-7. IIC Data I/O Register (IICD) Table 11-7. IICD Field Descriptions Field Description 7-0 DATA Data -- In master transmit mode, when data is written to the IICD, a data transfer is initiated. The most significant bit is sent first. In master receive mode, reading this register initiates receiving of the next byte of data. NOTE When transitioning out of master receive mode, the IIC mode should be switched before reading the IICD register to prevent an inadvertent initiation of a master receive data transfer. In slave mode, the same functions are available after an address match has occurred. The TX bit in IICC must correctly reflect the desired direction of transfer in master and slave modes for the transmission to begin. For instance, if the IIC is configured for master transmit but a master receive is desired, reading the IICD does not initiate the receive. Reading the IICD returns the last byte received while the IIC is configured in master receive or slave receive modes. The IICD does not reflect every byte transmitted on the IIC bus, nor can software verify that a byte has been written to the IICD correctly by reading it back. In master transmit mode, the first byte of data written to IICD following assertion of MST is used for the address transfer and should comprise of the calling address (in bit 7 to bit 1) concatenated with the required R/W bit (in position bit 0). 11.3.6 IIC Control Register 2 (IICC2) 7 6 GCAEN ADEXT 0 0 R 5 4 3 0 0 0 2 1 0 AD10 AD9 AD8 0 0 0 W Reset 0 0 0 = Unimplemented or Reserved Figure 11-8. IIC Control Register (IICC2) MC9S08DZ60 Series Data Sheet, Rev. 4 208 Freescale Semiconductor Chapter 11 Inter-Integrated Circuit (S08IICV2) Table 11-8. IICC2 Field Descriptions Field Description 7 GCAEN General Call Address Enable. The GCAEN bit enables or disables general call address. 0 General call address is disabled 1 General call address is enabled 6 ADEXT Address Extension. The ADEXT bit controls the number of bits used for the slave address. 0 7-bit address scheme 1 10-bit address scheme 2-0 AD[10:8] Slave Address. The AD[10:8] field contains the upper three bits of the slave address in the 10-bit address scheme. This field is only valid when the ADEXT bit is set. 11.4 Functional Description This section provides a complete functional description of the IIC module. 11.4.1 IIC Protocol The IIC bus system uses a serial data line (SDA) and a serial clock line (SCL) for data transfer. All devices connected to it must have open drain or open collector outputs. A logic AND function is exercised on both lines with external pull-up resistors. The value of these resistors is system dependent. Normally, a standard communication is composed of four parts: * Start signal * Slave address transmission * Data transfer * Stop signal The stop signal should not be confused with the CPU stop instruction. The IIC bus system communication is described briefly in the following sections and illustrated in Figure 11-9. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 209 Chapter 11 Inter-Integrated Circuit (S08IICV2) msb SCL 1 SDA lsb 2 3 4 5 6 7 8 msb 9 AD7 AD6 AD5 AD4 AD3 AD2 AD1 R/W Start Signal 1 SDA 3 4 5 6 7 8 Calling Address 3 4 5 6 7 8 D7 D6 D5 D4 D3 D2 D1 D0 1 XX Read/ Ack Write Bit Repeated Start Signal 9 No Ack Bit msb 9 AD7 AD6 AD5 AD4 AD3 AD2 AD1 R/W Start Signal 2 Data Byte lsb 2 1 Read/ Ack Write Bit Calling Address msb SCL XXX lsb Stop Signal lsb 2 3 4 5 6 7 8 9 AD7 AD6 AD5 AD4 AD3 AD2 AD1 R/W New Calling Address Read/ Write No Ack Bit Stop Signal Figure 11-9. IIC Bus Transmission Signals 11.4.1.1 Start Signal When the bus is free, no master device is engaging the bus (SCL and SDA lines are at logical high), a master may initiate communication by sending a start signal. As shown in Figure 11-9, a start signal is defined as a high-to-low transition of SDA while SCL is high. This signal denotes the beginning of a new data transfer (each data transfer may contain several bytes of data) and brings all slaves out of their idle states. 11.4.1.2 Slave Address Transmission The first byte of data transferred immediately after the start signal is the slave address transmitted by the master. This is a seven-bit calling address followed by a R/W bit. The R/W bit tells the slave the desired direction of data transfer. 1 = Read transfer, the slave transmits data to the master. 0 = Write transfer, the master transmits data to the slave. Only the slave with a calling address that matches the one transmitted by the master responds by sending back an acknowledge bit. This is done by pulling the SDA low at the ninth clock (see Figure 11-9). No two slaves in the system may have the same address. If the IIC module is the master, it must not transmit an address equal to its own slave address. The IIC cannot be master and slave at the same time. However, if arbitration is lost during an address cycle, the IIC reverts to slave mode and operates correctly even if it is being addressed by another master. MC9S08DZ60 Series Data Sheet, Rev. 4 210 Freescale Semiconductor Chapter 11 Inter-Integrated Circuit (S08IICV2) 11.4.1.3 Data Transfer Before successful slave addressing is achieved, the data transfer can proceed byte-by-byte in a direction specified by the R/W bit sent by the calling master. All transfers that come after an address cycle are referred to as data transfers, even if they carry sub-address information for the slave device Each data byte is 8 bits long. Data may be changed only while SCL is low and must be held stable while SCL is high as shown in Figure 11-9. There is one clock pulse on SCL for each data bit, the msb being transferred first. Each data byte is followed by a 9th (acknowledge) bit, which is signalled from the receiving device. An acknowledge is signalled by pulling the SDA low at the ninth clock. In summary, one complete data transfer needs nine clock pulses. If the slave receiver does not acknowledge the master in the ninth bit time, the SDA line must be left high by the slave. The master interprets the failed acknowledge as an unsuccessful data transfer. If the master receiver does not acknowledge the slave transmitter after a data byte transmission, the slave interprets this as an end of data transfer and releases the SDA line. In either case, the data transfer is aborted and the master does one of two things: * Relinquishes the bus by generating a stop signal. * Commences a new calling by generating a repeated start signal. 11.4.1.4 Stop Signal The master can terminate the communication by generating a stop signal to free the bus. However, the master may generate a start signal followed by a calling command without generating a stop signal first. This is called repeated start. A stop signal is defined as a low-to-high transition of SDA while SCL at logical 1 (see Figure 11-9). The master can generate a stop even if the slave has generated an acknowledge at which point the slave must release the bus. 11.4.1.5 Repeated Start Signal As shown in Figure 11-9, a repeated start signal is a start signal generated without first generating a stop signal to terminate the communication. This is used by the master to communicate with another slave or with the same slave in different mode (transmit/receive mode) without releasing the bus. 11.4.1.6 Arbitration Procedure The IIC bus is a true multi-master bus that allows more than one master to be connected on it. If two or more masters try to control the bus at the same time, a clock synchronization procedure determines the bus clock, for which the low period is equal to the longest clock low period and the high is equal to the shortest one among the masters. The relative priority of the contending masters is determined by a data arbitration procedure, a bus master loses arbitration if it transmits logic 1 while another master transmits logic 0. The losing masters immediately switch over to slave receive mode and stop driving SDA output. In this case, MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 211 Chapter 11 Inter-Integrated Circuit (S08IICV2) the transition from master to slave mode does not generate a stop condition. Meanwhile, a status bit is set by hardware to indicate loss of arbitration. 11.4.1.7 Clock Synchronization Because wire-AND logic is performed on the SCL line, a high-to-low transition on the SCL line affects all the devices connected on the bus. The devices start counting their low period and after a device's clock has gone low, it holds the SCL line low until the clock high state is reached. However, the change of low to high in this device clock may not change the state of the SCL line if another device clock is still within its low period. Therefore, synchronized clock SCL is held low by the device with the longest low period. Devices with shorter low periods enter a high wait state during this time (see Figure 11-10). When all devices concerned have counted off their low period, the synchronized clock SCL line is released and pulled high. There is then no difference between the device clocks and the state of the SCL line and all the devices start counting their high periods. The first device to complete its high period pulls the SCL line low again. Delay Start Counting High Period SCL1 SCL2 SCL Internal Counter Reset Figure 11-10. IIC Clock Synchronization 11.4.1.8 Handshaking The clock synchronization mechanism can be used as a handshake in data transfer. Slave devices may hold the SCL low after completion of one byte transfer (9 bits). In such a case, it halts the bus clock and forces the master clock into wait states until the slave releases the SCL line. 11.4.1.9 Clock Stretching The clock synchronization mechanism can be used by slaves to slow down the bit rate of a transfer. After the master has driven SCL low the slave can drive SCL low for the required period and then release it. If the slave SCL low period is greater than the master SCL low period then the resulting SCL bus signal low period is stretched. MC9S08DZ60 Series Data Sheet, Rev. 4 212 Freescale Semiconductor Chapter 11 Inter-Integrated Circuit (S08IICV2) 11.4.2 10-bit Address For 10-bit addressing, 0x11110 is used for the first 5 bits of the first address byte. Various combinations of read/write formats are possible within a transfer that includes 10-bit addressing. 11.4.2.1 Master-Transmitter Addresses a Slave-Receiver The transfer direction is not changed (see Table 11-9). When a 10-bit address follows a start condition, each slave compares the first seven bits of the first byte of the slave address (11110XX) with its own address and tests whether the eighth bit (R/W direction bit) is 0. More than one device can find a match and generate an acknowledge (A1). Then, each slave that finds a match compares the eight bits of the second byte of the slave address with its own address. Only one slave finds a match and generates an acknowledge (A2). The matching slave remains addressed by the master until it receives a stop condition (P) or a repeated start condition (Sr) followed by a different slave address. S Slave Address 1st 7 bits R/W 11110 + AD10 + AD9 0 A1 Slave Address 2nd byte AD[8:1] A2 Data A ... Data A/A P Table 11-9. Master-Transmitter Addresses Slave-Receiver with a 10-bit Address After the master-transmitter has sent the first byte of the 10-bit address, the slave-receiver sees an IIC interrupt. Software must ensure the contents of IICD are ignored and not treated as valid data for this interrupt. 11.4.2.2 Master-Receiver Addresses a Slave-Transmitter The transfer direction is changed after the second R/W bit (see Table 11-10). Up to and including acknowledge bit A2, the procedure is the same as that described for a master-transmitter addressing a slave-receiver. After the repeated start condition (Sr), a matching slave remembers that it was addressed before. This slave then checks whether the first seven bits of the first byte of the slave address following Sr are the same as they were after the start condition (S) and tests whether the eighth (R/W) bit is 1. If there is a match, the slave considers that it has been addressed as a transmitter and generates acknowledge A3. The slave-transmitter remains addressed until it receives a stop condition (P) or a repeated start condition (Sr) followed by a different slave address. After a repeated start condition (Sr), all other slave devices also compare the first seven bits of the first byte of the slave address with their own addresses and test the eighth (R/W) bit. However, none of them are addressed because R/W = 1 (for 10-bit devices) or the 11110XX slave address (for 7-bit devices) does not match. S Slave Address 1st 7 bits R/W 11110 + AD10 + AD9 0 A1 Slave Address 2nd byte AD[8:1] A2 Sr Slave Address 1st 7 bits R/W 11110 + AD10 + AD9 1 A3 Data A ... Data A P Table 11-10. Master-Receiver Addresses a Slave-Transmitter with a 10-bit Address After the master-receiver has sent the first byte of the 10-bit address, the slave-transmitter sees an IIC interrupt. Software must ensure the contents of IICD are ignored and not treated as valid data for this interrupt. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 213 Chapter 11 Inter-Integrated Circuit (S08IICV2) 11.4.3 General Call Address General calls can be requested in 7-bit address or 10-bit address. If the GCAEN bit is set, the IIC matches the general call address as well as its own slave address. When the IIC responds to a general call, it acts as a slave-receiver and the IAAS bit is set after the address cycle. Software must read the IICD register after the first byte transfer to determine whether the address matches is its own slave address or a general call. If the value is 00, the match is a general call. If the GCAEN bit is clear, the IIC ignores any data supplied from a general call address by not issuing an acknowledgement. 11.5 Resets The IIC is disabled after reset. The IIC cannot cause an MCU reset. 11.6 Interrupts The IIC generates a single interrupt. An interrupt from the IIC is generated when any of the events in Table 11-11 occur, provided the IICIE bit is set. The interrupt is driven by bit IICIF (of the IIC status register) and masked with bit IICIE (of the IIC control register). The IICIF bit must be cleared by software by writing a 1 to it in the interrupt routine. You can determine the interrupt type by reading the status register. Table 11-11. Interrupt Summary 11.6.1 Interrupt Source Status Flag Local Enable Complete 1-byte transfer TCF IICIF IICIE Match of received calling address IAAS IICIF IICIE Arbitration Lost ARBL IICIF IICIE Byte Transfer Interrupt The TCF (transfer complete flag) bit is set at the falling edge of the ninth clock to indicate the completion of byte transfer. 11.6.2 Address Detect Interrupt When the calling address matches the programmed slave address (IIC address register) or when the GCAEN bit is set and a general call is received, the IAAS bit in the status register is set. The CPU is interrupted, provided the IICIE is set. The CPU must check the SRW bit and set its Tx mode accordingly. 11.6.3 Arbitration Lost Interrupt The IIC is a true multi-master bus that allows more than one master to be connected on it. If two or more masters try to control the bus at the same time, the relative priority of the contending masters is determined by a data arbitration procedure. The IIC module asserts this interrupt when it loses the data arbitration process and the ARBL bit in the status register is set. MC9S08DZ60 Series Data Sheet, Rev. 4 214 Freescale Semiconductor Chapter 11 Inter-Integrated Circuit (S08IICV2) Arbitration is lost in the following circumstances: * SDA sampled as a low when the master drives a high during an address or data transmit cycle. * SDA sampled as a low when the master drives a high during the acknowledge bit of a data receive cycle. * A start cycle is attempted when the bus is busy. * A repeated start cycle is requested in slave mode. * A stop condition is detected when the master did not request it. This bit must be cleared by software writing a 1 to it. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 215 Chapter 11 Inter-Integrated Circuit (S08IICV2) 11.7 1. 2. 3. 4. 5. 1. 2. 3. 4. 5. 6. 7. Initialization/Application Information Module Initialization (Slave) Write: IICC2 -- to enable or disable general call -- to select 10-bit or 7-bit addressing mode Write: IICA -- to set the slave address Write: IICC1 -- to enable IIC and interrupts Initialize RAM variables (IICEN = 1 and IICIE = 1) for transmit data Initialize RAM variables used to achieve the routine shown in Figure 11-12 Module Initialization (Master) Write: IICF -- to set the IIC baud rate (example provided in this chapter) Write: IICC1 -- to enable IIC and interrupts Initialize RAM variables (IICEN = 1 and IICIE = 1) for transmit data Initialize RAM variables used to achieve the routine shown in Figure 11-12 Write: IICC1 -- to enable TX Write: IICC1 -- to enable MST (master mode) Write: IICD -- with the address of the target slave. (The lsb of this byte determines whether the communication is master receive or transmit.) Module Use The routine shown in Figure 11-12 can handle both master and slave IIC operations. For slave operation, an incoming IIC message that contains the proper address begins IIC communication. For master operation, communication must be initiated by writing to the IICD register. Register Model 0 AD[7:1] IICA When addressed as a slave (in slave mode), the module responds to this address MULT IICF ICR Baud rate = BUSCLK / (2 x MULT x (SCL DIVIDER)) IICC1 IICEN IICIE MST TX TXAK RSTA 0 0 BUSY ARBL 0 SRW IICIF RXAK AD9 AD8 Module configuration IICS TCF IAAS Module status flags DATA IICD Data register; Write to transmit IIC data read to read IIC data IICC2 GCAEN ADEXT 0 0 0 AD10 Address configuration Figure 11-11. IIC Module Quick Start MC9S08DZ60 Series Data Sheet, Rev. 4 216 Freescale Semiconductor Chapter 11 Inter-Integrated Circuit (S08IICV2) Clear IICIF Master Mode ? Y TX N Y RX Tx/Rx ? Arbitration Lost ? N Last Byte Transmitted ? N Clear ARBL Y RXAK=0 ? Last Byte to Be Read ? N N N Y Y IAAS=1 ? Y IAAS=1 ? Y Address Transfer See Note 1 Y End of Addr Cycle (Master Rx) ? Y Y (Read) 2nd Last Byte to Be Read ? N SRW=1 ? Write Next Byte to IICD Set TXACK =1 Generate Stop Signal (MST = 0) Switch to Rx Mode Generate Stop Signal (MST = 0) Read Data from IICD and Store ACK from Receiver ? N Read Data from IICD and Store Tx Next Byte Write Data to IICD Dummy Read from IICD TX Y Set TX Mode RX TX/RX ? N (Write) N N Data Transfer See Note 2 Set RX Mode Switch to Rx Mode Dummy Read from IICD Dummy Read from IICD RTI NOTES: 1. If general call is enabled, a check must be done to determine whether the received address was a general call address (0x00). If the received address was a general call address, then the general call must be handled by user software. 2. When 10-bit addressing is used to address a slave, the slave sees an interrupt following the first byte of the extended address. User software must ensure that for this interrupt, the contents of IICD are ignored and not treated as a valid data transfer Figure 11-12. Typical IIC Interrupt Routine MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 217 Chapter 11 Inter-Integrated Circuit (S08IICV2) MC9S08DZ60 Series Data Sheet, Rev. 4 218 Freescale Semiconductor Chapter 12 Freescale Controller Area Network (S08MSCANV1) 12.1 Introduction The Freescale controller area network (MSCAN) is a communication controller implementing the CAN 2.0A/B protocol as defined in the Bosch specification dated September 1991. To fully understand the MSCAN specification, it is recommended that the Bosch specification be read first to gain familiarity with the terms and concepts contained within this document. Though not exclusively intended for automotive applications, CAN protocol is designed to meet the specific requirements of a vehicle serial data bus: real-time processing, reliable operation in the EMI environment of a vehicle, cost-effectiveness, and required bandwidth. MSCAN uses an advanced buffer arrangement resulting in predictable real-time behavior and simplified application software. The MSCAN module is available in all devices in the MC9S08DZ60 Series. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 219 PORT A PTA7/PIA7/ADP7/IRQ PTA6/PIA6/ADP6 PTA5/PIA5/ADP5 PTA4/PIA4/ADP4 PTA3/PIA3/ADP3/ACMP1O PTA2/PIA2/ADP2/ACMP1PTA1/PIA1/ADP1/ACMP1+ PTA0/PIA0/ADP0/MCLK PORT B PTB7/PIB7/ADP15 PTB6/PIB6/ADP14 PTB5/PIB5/ADP13 PTB4/PIB4/ADP12 PTB3/PIB3/ADP11 PTB2/PIB2/ADP10 PTB1/PIB1/ADP9 PTB0/PIB0/ADP8 PORT C PTC7/ADP23 PTC6/ADP22 PTC5/ADP21 PTC4/ADP20 PTC3/ADP19 PTC2/ADP18 PTC1/ADP17 PTC0/ADP16 PORT D PTD7/PID7/TPM1CH5 PTD6/PID6/TPM1CH4 PTD5/PID5/TPM1CH3 PTD4/PID4/TPM1CH2 PTD3/PID3/TPM1CH1 PTD2/PID2/TPM1CH0 PTD1/PID1/TPM2CH1 PTD0/PID0/TPM2CH0 PORT E PTE7/RxD2/RXCAN PTE6/TxD2/TXCAN PTE5/SDA/MISO PTE4/SCL/MOSI PTE3/SPSCK PTE2/SS PTE1/RxD1 PTE0/TxD1 PORT F PTF7 PTF6/ACMP2O PTF5/ACMP2PTF4/ACMP2+ PTF3/TPM2CLK/SDA PTF2/TPM1CLK/SCL PTF1/RxD2 PTF0/TxD2 PORT G Chapter 12 Freescale Controller Area Network (S08MSCANV1) PTG5 PTG4 PTG3 PTG2 PTG1/XTAL PTG0/EXTAL HCS08 CORE CPU BKGD/MS BDC ANALOG COMPARATOR (ACMP1) BKP ACMP1O ACMP1ACMP1+ HCS08 SYSTEM CONTROL RESETS AND INTERRUPTS MODES OF OPERATION POWER MANAGEMENT COP LVD INT IRQ ADP7-ADP0 24-CHANNEL,12-BIT ANALOG-TO-DIGITAL CONVERTER (ADC) VREFH VREFL VDDA VSSA USER FLASH MC9S0DZ60 = 60K MC9S0DZ48 = 48K MC9S0DZ32 = 32K MC9S0DZ16 = 16K USER EEPROM MC9S0DZ60 = 2K TPM1CH5 TPM1CH0 6 TPM1CLK 2-CHANNEL TIMER/PWM MODULE (TPM2) TPM2CH1, TPM2CH0 TPM2CLK CONTROLLER AREA NETWORK (MSCAN) SERIAL PERIPHERAL INTERFACE MODULE (SPI) DEBUG MODULE (DBG) SERIAL COMMUNICATIONS INTERFACE (SCI1) VOLTAGE REGULATOR ADP15-ADP8 ADP23-ADP16 6-CHANNEL TIMER/PWM MODULE (TPM1) USER RAM MC9S0DZ60 = 4K REAL-TIME COUNTER (RTC) VDD VDD VSS VSS 8 IRQ RESET ANALOG COMPARATOR (ACMP2) IIC MODULE (IIC) SERIAL COMMUNICATIONS INTERFACE (SCI2) RxCAN TxCAN MISO MOSI SPSCK SS RxD1 TxD1 ACMP2O ACMP2ACMP2+ SDA SCL RxD2 TxD2 MULTI-PURPOSE CLOCK GENERATOR (MCG) XTAL EXTAL OSCILLATOR (XOSC) - VREFH/VREFL internally connected to VDDA/VSSA in 48-pin and 32-pin packages - VDD and VSS pins are each internally connected to two pads in 32-pin package - Pin not connected in 48-pin and 32-pin packages - Pin not connected in 32-pin package Figure 12-1. MC9S08DZ60 Block Diagram MC9S08DZ60 Series Data Sheet, Rev. 4 220 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) 12.1.1 Features The basic features of the MSCAN are as follows: * Implementation of the CAN protocol -- Version 2.0A/B -- Standard and extended data frames -- Zero to eight bytes data length -- Programmable bit rate up to 1 Mbps1 -- Support for remote frames * Five receive buffers with FIFO storage scheme * Three transmit buffers with internal prioritization using a "local priority" concept * Flexible maskable identifier filter supports two full-size (32-bit) extended identifier filters, or four 16-bit filters, or eight 8-bit filters * Programmable wakeup functionality with integrated low-pass filter * Programmable loopback mode supports self-test operation * Programmable listen-only mode for monitoring of CAN bus * Programmable bus-off recovery functionality * Separate signalling and interrupt capabilities for all CAN receiver and transmitter error states (warning, error passive, bus-off) * Programmable MSCAN clock source either bus clock or oscillator clock * Internal timer for time-stamping of received and transmitted messages * Three low-power modes: sleep, power down, and MSCAN enable * Global initialization of configuration registers 12.1.2 Modes of Operation The following modes of operation are specific to the MSCAN. See Section 12.5, "Functional Description," for details. * Listen-Only Mode * MSCAN Sleep Mode * MSCAN Initialization Mode * MSCAN Power Down Mode * Loopback Self Test Mode 1. Depending on the actual bit timing and the clock jitter of the PLL. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 221 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) 12.1.3 Block Diagram MSCAN Oscillator Clock Bus Clock CANCLK MUX Presc. Tq Clk Receive/ Transmit Engine RXCAN TXCAN Transmit Interrupt Req. Receive Interrupt Req. Message Filtering and Buffering Control and Status Errors Interrupt Req. Wake-Up Interrupt Req. Configuration Registers Wake-Up Low Pass Filter Figure 12-2. MSCAN Block Diagram 12.2 External Signal Description The MSCAN uses two external pins: 12.2.1 RXCAN -- CAN Receiver Input Pin RXCAN is the MSCAN receiver input pin. 12.2.2 TXCAN -- CAN Transmitter Output Pin TXCAN is the MSCAN transmitter output pin. The TXCAN output pin represents the logic level on the CAN bus: 0 = Dominant state 1 = Recessive state 12.2.3 CAN System A typical CAN system with MSCAN is shown in Figure 12-3. Each CAN node is connected physically to the CAN bus lines through a transceiver device. The transceiver is capable of driving the large current needed for the CAN bus and has current protection against defective CAN or defective nodes. MC9S08DZ60 Series Data Sheet, Rev. 4 222 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) CAN node 2 CAN node 1 CAN node n MCU CAN Controller (MSCAN) TXCAN RXCAN Transceiver CAN_H CAN_L CAN Bus Figure 12-3. CAN System 12.3 Register Definition This section describes in detail all the registers and register bits in the MSCAN module. Each description includes a standard register diagram with an associated figure number. Details of register bit and field function follow the register diagrams, in bit order. All bits of all registers in this module are completely synchronous to internal clocks during a register read. 12.3.1 MSCAN Control Register 0 (CANCTL0) The CANCTL0 register provides various control bits of the MSCAN module as described below. R 7 6 RXFRM RXACT 5 4 3 2 1 0 TIME WUPE SLPRQ INITRQ 0 0 0 1 SYNCH CSWAI W Reset: 0 0 0 0 = Unimplemented Figure 12-4. MSCAN Control Register 0 (CANCTL0) NOTE The CANCTL0 register, except WUPE, INITRQ, and SLPRQ, is held in the reset state when the initialization mode is active (INITRQ = 1 and INITAK = 1). This register is writable again as soon as the initialization mode is exited (INITRQ = 0 and INITAK = 0). Read: Anytime Write: Anytime when out of initialization mode; exceptions are read-only RXACT and SYNCH, RXFRM (which is set by the module only), and INITRQ (which is also writable in initialization mode). MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 223 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) Table 12-1. CANCTL0 Register Field Descriptions Field Description 7 RXFRM1 Received Frame Flag -- This bit is read and clear only. It is set when a receiver has received a valid message correctly, independently of the filter configuration. After it is set, it remains set until cleared by software or reset. Clearing is done by writing a 1. Writing a 0 is ignored. This bit is not valid in loopback mode. 0 No valid message was received since last clearing this flag 1 A valid message was received since last clearing of this flag 6 RXACT Receiver Active Status -- This read-only flag indicates the MSCAN is receiving a message. The flag is controlled by the receiver front end. This bit is not valid in loopback mode. 0 MSCAN is transmitting or idle2 1 MSCAN is receiving a message (including when arbitration is lost)2 5 CSWAI3 CAN Stops in Wait Mode -- Enabling this bit allows for lower power consumption in wait mode by disabling all the clocks at the CPU bus interface to the MSCAN module. 0 The module is not affected during wait mode 1 The module ceases to be clocked during wait mode 4 SYNCH Synchronized Status -- This read-only flag indicates whether the MSCAN is synchronized to the CAN bus and able to participate in the communication process. It is set and cleared by the MSCAN. 0 MSCAN is not synchronized to the CAN bus 1 MSCAN is synchronized to the CAN bus 3 TIME Timer Enable -- This bit activates an internal 16-bit wide free running timer which is clocked by the bit clock rate. If the timer is enabled, a 16-bit time stamp will be assigned to each transmitted/received message within the active TX/RX buffer. As soon as a message is acknowledged on the CAN bus, the time stamp will be written to the highest bytes (0x000E, 0x000F) in the appropriate buffer (see Section 12.4, "Programmer's Model of Message Storage"). The internal timer is reset (all bits set to 0) when disabled. This bit is held low in initialization mode. 0 Disable internal MSCAN timer 1 Enable internal MSCAN timer 2 WUPE4 Wake-Up Enable -- This configuration bit allows the MSCAN to restart from sleep mode when traffic on CAN is detected (see Section 12.5.5.4, "MSCAN Sleep Mode"). This bit must be configured before sleep mode entry for the selected function to take effect. 0 Wake-up disabled -- The MSCAN ignores traffic on CAN 1 Wake-up enabled -- The MSCAN is able to restart MC9S08DZ60 Series Data Sheet, Rev. 4 224 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) Table 12-1. CANCTL0 Register Field Descriptions (continued) Field Description 1 SLPRQ5 Sleep Mode Request -- This bit requests the MSCAN to enter sleep mode, which is an internal power saving mode (see Section 12.5.5.4, "MSCAN Sleep Mode"). The sleep mode request is serviced when the CAN bus is idle, i.e., the module is not receiving a message and all transmit buffers are empty. The module indicates entry to sleep mode by setting SLPAK = 1 (see Section 12.3.2, "MSCAN Control Register 1 (CANCTL1)"). SLPRQ cannot be set while the WUPIF flag is set (see Section 12.3.4.1, "MSCAN Receiver Flag Register (CANRFLG)"). Sleep mode will be active until SLPRQ is cleared by the CPU or, depending on the setting of WUPE, the MSCAN detects activity on the CAN bus and clears SLPRQ itself. 0 Running -- The MSCAN functions normally 1 Sleep mode request -- The MSCAN enters sleep mode when CAN bus idle 0 INITRQ6,7 Initialization Mode Request -- When this bit is set by the CPU, the MSCAN skips to initialization mode (see Section 12.5.5.5, "MSCAN Initialization Mode"). Any ongoing transmission or reception is aborted and synchronization to the CAN bus is lost. The module indicates entry to initialization mode by setting INITAK = 1 (Section 12.3.2, "MSCAN Control Register 1 (CANCTL1)"). The following registers enter their hard reset state and restore their default values: CANCTL08, CANRFLG9, CANRIER10, CANTFLG, CANTIER, CANTARQ, CANTAAK, and CANTBSEL. The registers CANCTL1, CANBTR0, CANBTR1, CANIDAC, CANIDAR0-7, and CANIDMR0-7 can only be written by the CPU when the MSCAN is in initialization mode (INITRQ = 1 and INITAK = 1). The values of the error counters are not affected by initialization mode. When this bit is cleared by the CPU, the MSCAN restarts and then tries to synchronize to the CAN bus. If the MSCAN is not in bus-off state, it synchronizes after 11 consecutive recessive bits on the CAN bus; if the MSCAN is in bus-off state, it continues to wait for 128 occurrences of 11 consecutive recessive bits. Writing to other bits in CANCTL0, CANRFLG, CANRIER, CANTFLG, or CANTIER must be done only after initialization mode is exited, which is INITRQ = 0 and INITAK = 0. 0 Normal operation 1 MSCAN in initialization mode 1 The MSCAN must be in normal mode for this bit to become set. See the Bosch CAN 2.0A/B specification for a detailed definition of transmitter and receiver states. 3 In order to protect from accidentally violating the CAN protocol, the TXCAN pin is immediately forced to a recessive state when the CPU enters wait (CSWAI = 1) or stop mode (see Section 12.5.5.2, "Operation in Wait Mode" and Section 12.5.5.3, "Operation in Stop Mode"). 4 The CPU has to make sure that the WUPE bit and the WUPIE wake-up interrupt enable bit (see Section 12.3.5, "MSCAN Receiver Interrupt Enable Register (CANRIER)) is enabled, if the recovery mechanism from stop or wait is required. 5 The CPU cannot clear SLPRQ before the MSCAN has entered sleep mode (SLPRQ = 1 and SLPAK = 1). 6 The CPU cannot clear INITRQ before the MSCAN has entered initialization mode (INITRQ = 1 and INITAK = 1). 7 In order to protect from accidentally violating the CAN protocol, the TXCAN pin is immediately forced to a recessive state when the initialization mode is requested by the CPU. Thus, the recommended procedure is to bring the MSCAN into sleep mode (SLPRQ = 1 and SLPAK = 1) before requesting initialization mode. 8 Not including WUPE, INITRQ, and SLPRQ. 9 TSTAT1 and TSTAT0 are not affected by initialization mode. 10 RSTAT1 and RSTAT0 are not affected by initialization mode. 2 MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 225 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) 12.3.2 MSCAN Control Register 1 (CANCTL1) The CANCTL1 register provides various control bits and handshake status information of the MSCAN module as described below. 7 6 5 4 3 2 CANE CLKSRC LOOPB LISTEN BORM WUPM 0 0 0 1 0 0 R 1 0 SLPAK INITAK 0 1 W Reset: = Unimplemented Figure 12-5. MSCAN Control Register 1(CANCTL1) Read: Anytime Write: Anytime when INITRQ = 1 and INITAK = 1, except CANE which is write once in normal and anytime in special system operation modes when the MSCAN is in initialization mode (INITRQ = 1 and INITAK = 1). Table 12-2. CANCTL1 Register Field Descriptions Field 7 CANE Description MSCAN Enable 0 MSCAN module is disabled 1 MSCAN module is enabled 6 CLKSRC MSCAN Clock Source -- This bit defines the clock source for the MSCAN module (only for systems with a clock generation module; Section 12.5.3.3, "Clock System," and Section Figure 12-42., "MSCAN Clocking Scheme,"). 0 MSCAN clock source is the oscillator clock 1 MSCAN clock source is the bus clock 5 LOOPB Loopback Self Test Mode -- When this bit is set, the MSCAN performs an internal loopback which can be used for self test operation. The bit stream output of the transmitter is fed back to the receiver internally.Section 12.5.4.6, "Loopback Self Test Mode. 0 Loopback self test disabled 1 Loopback self test enabled 4 LISTEN Listen Only Mode -- This bit configures the MSCAN as a CAN bus monitor. When LISTEN is set, all valid CAN messages with matching ID are received, but no acknowledgement or error frames are sent out (see Section 12.5.4.4, "Listen-Only Mode"). In addition, the error counters are frozen. Listen only mode supports applications which require "hot plugging" or throughput analysis. The MSCAN is unable to transmit any messages when listen only mode is active. 0 Normal operation 1 Listen only mode activated 3 BORM Bus-Off Recovery Mode -- This bits configures the bus-off state recovery mode of the MSCAN. Refer to Section 12.6.2, "Bus-Off Recovery," for details. 0 Automatic bus-off recovery (see Bosch CAN 2.0A/B protocol specification) 1 Bus-off recovery upon user request 2 WUPM Wake-Up Mode -- If WUPE in CANCTL0 is enabled, this bit defines whether the integrated low-pass filter is applied to protect the MSCAN from spurious wake-up (see Section 12.5.5.4, "MSCAN Sleep Mode"). 0 MSCAN wakes up on any dominant level on the CAN bus 1 MSCAN wakes up only in case of a dominant pulse on the CAN bus that has a length of Twup MC9S08DZ60 Series Data Sheet, Rev. 4 226 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) Table 12-2. CANCTL1 Register Field Descriptions (continued) Field Description 1 SLPAK Sleep Mode Acknowledge -- This flag indicates whether the MSCAN module has entered sleep mode (see Section 12.5.5.4, "MSCAN Sleep Mode"). It is used as a handshake flag for the SLPRQ sleep mode request. Sleep mode is active when SLPRQ = 1 and SLPAK = 1. Depending on the setting of WUPE, the MSCAN will clear the flag if it detects activity on the CAN bus while in sleep mode.CPU clearing the SLPRQ bit will also reset the SLPAK bit. 0 Running -- The MSCAN operates normally 1 Sleep mode active -- The MSCAN has entered sleep mode 0 INITAK Initialization Mode Acknowledge -- This flag indicates whether the MSCAN module is in initialization mode (see Section 12.5.5.5, "MSCAN Initialization Mode"). It is used as a handshake flag for the INITRQ initialization mode request. Initialization mode is active when INITRQ = 1 and INITAK = 1. The registers CANCTL1, CANBTR0, CANBTR1, CANIDAC, CANIDAR0-CANIDAR7, and CANIDMR0-CANIDMR7 can be written only by the CPU when the MSCAN is in initialization mode. 0 Running -- The MSCAN operates normally 1 Initialization mode active -- The MSCAN is in initialization mode 12.3.3 MSCAN Bus Timing Register 0 (CANBTR0) The CANBTR0 register configures various CAN bus timing parameters of the MSCAN module. 7 6 5 4 3 2 1 0 SJW1 SJW0 BRP5 BRP4 BRP3 BRP2 BRP1 BRP0 0 0 0 0 0 0 0 0 R W Reset: Figure 12-6. MSCAN Bus Timing Register 0 (CANBTR0) Read: Anytime Write: Anytime in initialization mode (INITRQ = 1 and INITAK = 1) Table 12-3. CANBTR0 Register Field Descriptions Field Description 7:6 SJW[1:0] Synchronization Jump Width -- The synchronization jump width defines the maximum number of time quanta (Tq) clock cycles a bit can be shortened or lengthened to achieve resynchronization to data transitions on the CAN bus (see Table 12-4). 5:0 BRP[5:0] Baud Rate Prescaler -- These bits determine the time quanta (Tq) clock which is used to build up the bit timing (see Table 12-5). Table 12-4. Synchronization Jump Width SJW1 SJW0 Synchronization Jump Width 0 0 1 Tq clock cycle 0 1 2 Tq clock cycles 1 0 3 Tq clock cycles 1 1 4 Tq clock cycles MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 227 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) Table 12-5. Baud Rate Prescaler 12.3.4 BRP5 BRP4 BRP3 BRP2 BRP1 BRP0 Prescaler value (P) 0 0 0 0 0 0 1 0 0 0 0 0 1 2 0 0 0 0 1 0 3 0 0 0 0 1 1 4 : : : : : : : 1 1 1 1 1 1 64 MSCAN Bus Timing Register 1 (CANBTR1) The CANBTR1 register configures various CAN bus timing parameters of the MSCAN module. 7 6 5 4 3 2 1 0 SAMP TSEG22 TSEG21 TSEG20 TSEG13 TSEG12 TSEG11 TSEG10 0 0 0 0 0 0 0 0 R W Reset: Figure 12-7. MSCAN Bus Timing Register 1 (CANBTR1) Read: Anytime Write: Anytime in initialization mode (INITRQ = 1 and INITAK = 1) Table 12-6. CANBTR1 Register Field Descriptions Field Description 7 SAMP Sampling -- This bit determines the number of CAN bus samples taken per bit time. 0 One sample per bit. 1 Three samples per bit1. If SAMP = 0, the resulting bit value is equal to the value of the single bit positioned at the sample point. If SAMP = 1, the resulting bit value is determined by using majority rule on the three total samples. For higher bit rates, it is recommended that only one sample is taken per bit time (SAMP = 0). 6:4 Time Segment 2 -- Time segments within the bit time fix the number of clock cycles per bit time and the location TSEG2[2:0] of the sample point (see Figure 12-43). Time segment 2 (TSEG2) values are programmable as shown in Table 12-7. 3:0 Time Segment 1 -- Time segments within the bit time fix the number of clock cycles per bit time and the location TSEG1[3:0] of the sample point (see Figure 12-43). Time segment 1 (TSEG1) values are programmable as shown in Table 12-8. 1 In this case, PHASE_SEG1 must be at least 2 time quanta (Tq). MC9S08DZ60 Series Data Sheet, Rev. 4 228 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) Table 12-7. Time Segment 2 Values 1 TSEG22 TSEG21 TSEG20 Time Segment 2 0 0 0 1 Tq clock cycle1 0 0 1 2 Tq clock cycles : : : : 1 1 0 7 Tq clock cycles 1 1 1 8 Tq clock cycles This setting is not valid. Please refer to Table 12-35 for valid settings. Table 12-8. Time Segment 1 Values 1 TSEG13 TSEG12 TSEG11 TSEG10 Time segment 1 0 0 0 0 1 Tq clock cycle1 0 0 0 1 2 Tq clock cycles1 0 0 1 0 3 Tq clock cycles1 0 0 1 1 4 Tq clock cycles : : : : : 1 1 1 0 15 Tq clock cycles 1 1 1 1 16 Tq clock cycles This setting is not valid. Please refer to Table 12-35 for valid settings. The bit time is determined by the oscillator frequency, the baud rate prescaler, and the number of time quanta (Tq) clock cycles per bit (as shown in Table 12-7 and Table 12-8). Eqn. 12-1 ( Prescaler value ) Bit Time = ------------------------------------------------------ * ( 1 + TimeSegment1 + TimeSegment2 ) f CANCLK 12.3.4.1 MSCAN Receiver Flag Register (CANRFLG) A flag can be cleared only by software (writing a 1 to the corresponding bit position) when the condition which caused the setting is no longer valid. Every flag has an associated interrupt enable bit in the CANRIER register. 7 6 WUPIF CSCIF 0 0 R 5 4 3 2 RSTAT1 RSTAT0 TSTAT1 TSTAT0 1 0 OVRIF RXF 0 0 W Reset: 0 0 0 0 = Unimplemented Figure 12-8. MSCAN Receiver Flag Register (CANRFLG) MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 229 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) NOTE The CANRFLG register is held in the reset state1 when the initialization mode is active (INITRQ = 1 and INITAK = 1). This register is writable again as soon as the initialization mode is exited (INITRQ = 0 and INITAK = 0). Read: Anytime Write: Anytime when out of initialization mode, except RSTAT[1:0] and TSTAT[1:0] flags which are read-only; write of 1 clears flag; write of 0 is ignored. Table 12-9. CANRFLG Register Field Descriptions Field Description 7 WUPIF Wake-Up Interrupt Flag -- If the MSCAN detects CAN bus activity while in sleep mode (see Section 12.5.5.4, "MSCAN Sleep Mode,") and WUPE = 1 in CANTCTL0 (see Section 12.3.1, "MSCAN Control Register 0 (CANCTL0)"), the module will set WUPIF. If not masked, a wake-up interrupt is pending while this flag is set. 0 No wake-up activity observed while in sleep mode 1 MSCAN detected activity on the CAN bus and requested wake-up 6 CSCIF CAN Status Change Interrupt Flag -- This flag is set when the MSCAN changes its current CAN bus status due to the actual value of the transmit error counter (TEC) and the receive error counter (REC). An additional 4-bit (RSTAT[1:0], TSTAT[1:0]) status register, which is split into separate sections for TEC/REC, informs the system on the actual CAN bus status (see Section 12.3.5, "MSCAN Receiver Interrupt Enable Register (CANRIER)"). If not masked, an error interrupt is pending while this flag is set. CSCIF provides a blocking interrupt. That guarantees that the receiver/transmitter status bits (RSTAT/TSTAT) are only updated when no CAN status change interrupt is pending. If the TECs/RECs change their current value after the CSCIF is asserted, which would cause an additional state change in the RSTAT/TSTAT bits, these bits keep their status until the current CSCIF interrupt is cleared again. 0 No change in CAN bus status occurred since last interrupt 1 MSCAN changed current CAN bus status 5:4 Receiver Status Bits -- The values of the error counters control the actual CAN bus status of the MSCAN. As RSTAT[1:0] soon as the status change interrupt flag (CSCIF) is set, these bits indicate the appropriate receiver related CAN bus status of the MSCAN. The coding for the bits RSTAT1, RSTAT0 is: 00 RxOK: 0 receive error counter 96 01 RxWRN: 96 < receive error counter 127 10 RxERR: 127 < receive error counter 11 Bus-off1: transmit error counter > 255 3:2 Transmitter Status Bits -- The values of the error counters control the actual CAN bus status of the MSCAN. TSTAT[1:0] As soon as the status change interrupt flag (CSCIF) is set, these bits indicate the appropriate transmitter related CAN bus status of the MSCAN. The coding for the bits TSTAT1, TSTAT0 is: 00 TxOK: 0 transmit error counter 96 01 TxWRN: 96 < transmit error counter 127 10 TxERR: 127 < transmit error counter 255 11 Bus-Off: transmit error counter > 255 1. The RSTAT[1:0], TSTAT[1:0] bits are not affected by initialization mode. MC9S08DZ60 Series Data Sheet, Rev. 4 230 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) Table 12-9. CANRFLG Register Field Descriptions (continued) Field Description 1 OVRIF Overrun Interrupt Flag -- This flag is set when a data overrun condition occurs. If not masked, an error interrupt is pending while this flag is set. 0 No data overrun condition 1 A data overrun detected 0 RXF2 Receive Buffer Full Flag -- RXF is set by the MSCAN when a new message is shifted in the receiver FIFO. This flag indicates whether the shifted buffer is loaded with a correctly received message (matching identifier, matching cyclic redundancy code (CRC) and no other errors detected). After the CPU has read that message from the RxFG buffer in the receiver FIFO, the RXF flag must be cleared to release the buffer. A set RXF flag prohibits the shifting of the next FIFO entry into the foreground buffer (RxFG). If not masked, a receive interrupt is pending while this flag is set. 0 No new message available within the RxFG 1 The receiver FIFO is not empty. A new message is available in the RxFG 1 Redundant Information for the most critical CAN bus status which is "bus-off". This only occurs if the Tx error counter exceeds a number of 255 errors. Bus-off affects the receiver state. As soon as the transmitter leaves its bus-off state the receiver state skips to RxOK too. Refer also to TSTAT[1:0] coding in this register. 2 To ensure data integrity, do not read the receive buffer registers while the RXF flag is cleared. For MCUs with dual CPUs, reading the receive buffer registers while the RXF flag is cleared may result in a CPU fault condition. 12.3.5 MSCAN Receiver Interrupt Enable Register (CANRIER) This register contains the interrupt enable bits for the interrupt flags described in the CANRFLG register. 7 6 5 4 3 2 1 0 WUPIE CSCIE RSTATE1 RSTATE0 TSTATE1 TSTATE0 OVRIE RXFIE 0 0 0 0 0 0 0 0 R W Reset: Figure 12-9. MSCAN Receiver Interrupt Enable Register (CANRIER) NOTE The CANRIER register is held in the reset state when the initialization mode is active (INITRQ=1 and INITAK=1). This register is writable when not in initialization mode (INITRQ=0 and INITAK=0). The RSTATE[1:0], TSTATE[1:0] bits are not affected by initialization mode. Read: Anytime Write: Anytime when not in initialization mode MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 231 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) Table 12-10. CANRIER Register Field Descriptions Field 7 WUPIE1 6 CSCIE Description Wake-Up Interrupt Enable 0 No interrupt request is generated from this event. 1 A wake-up event causes a Wake-Up interrupt request. CAN Status Change Interrupt Enable 0 No interrupt request is generated from this event. 1 A CAN Status Change event causes an error interrupt request. 5:4 Receiver Status Change Enable -- These RSTAT enable bits control the sensitivity level in which receiver state RSTATE[1:0] changes are causing CSCIF interrupts. Independent of the chosen sensitivity level the RSTAT flags continue to indicate the actual receiver state and are only updated if no CSCIF interrupt is pending. 00 Do not generate any CSCIF interrupt caused by receiver state changes. 01 Generate CSCIF interrupt only if the receiver enters or leaves "bus-off" state. Discard other receiver state changes for generating CSCIF interrupt. 10 Generate CSCIF interrupt only if the receiver enters or leaves "RxErr" or "bus-off"2 state. Discard other receiver state changes for generating CSCIF interrupt. 11 Generate CSCIF interrupt on all state changes. 3:2 Transmitter Status Change Enable -- These TSTAT enable bits control the sensitivity level in which transmitter TSTATE[1:0] state changes are causing CSCIF interrupts. Independent of the chosen sensitivity level, the TSTAT flags continue to indicate the actual transmitter state and are only updated if no CSCIF interrupt is pending. 00 Do not generate any CSCIF interrupt caused by transmitter state changes. 01 Generate CSCIF interrupt only if the transmitter enters or leaves "bus-off" state. Discard other transmitter state changes for generating CSCIF interrupt. 10 Generate CSCIF interrupt only if the transmitter enters or leaves "TxErr" or "bus-off" state. Discard other transmitter state changes for generating CSCIF interrupt. 11 Generate CSCIF interrupt on all state changes. 1 OVRIE Overrun Interrupt Enable 0 No interrupt request is generated from this event. 1 An overrun event causes an error interrupt request. 0 RXFIE Receiver Full Interrupt Enable 0 No interrupt request is generated from this event. 1 A receive buffer full (successful message reception) event causes a receiver interrupt request. 1 WUPIE and WUPE (see Section 12.3.1, "MSCAN Control Register 0 (CANCTL0)") must both be enabled if the recovery mechanism from stop or wait is required. 2 Bus-off state is defined by the CAN standard (see Bosch CAN 2.0A/B protocol specification: for only transmitters. Because the only possible state change for the transmitter from bus-off to TxOK also forces the receiver to skip its current state to RxOK, the coding of the RXSTAT[1:0] flags define an additional bus-off state for the receiver (see Section 12.3.4.1, "MSCAN Receiver Flag Register (CANRFLG)"). 12.3.6 MSCAN Transmitter Flag Register (CANTFLG) The transmit buffer empty flags each have an associated interrupt enable bit in the CANTIER register. MC9S08DZ60 Series Data Sheet, Rev. 4 232 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) R 7 6 5 4 3 0 0 0 0 0 2 1 0 TXE2 TXE1 TXE0 1 1 1 W Reset: 0 0 0 0 0 = Unimplemented Figure 12-10. MSCAN Transmitter Flag Register (CANTFLG) NOTE The CANTFLG register is held in the reset state when the initialization mode is active (INITRQ = 1 and INITAK = 1). This register is writable when not in initialization mode (INITRQ = 0 and INITAK = 0). Read: Anytime Write: Anytime for TXEx flags when not in initialization mode; write of 1 clears flag, write of 0 is ignored Table 12-11. CANTFLG Register Field Descriptions Field Description 2:0 TXE[2:0] Transmitter Buffer Empty -- This flag indicates that the associated transmit message buffer is empty, and thus not scheduled for transmission. The CPU must clear the flag after a message is set up in the transmit buffer and is due for transmission. The MSCAN sets the flag after the message is sent successfully. The flag is also set by the MSCAN when the transmission request is successfully aborted due to a pending abort request (see Section 12.3.8, "MSCAN Transmitter Message Abort Request Register (CANTARQ)"). If not masked, a transmit interrupt is pending while this flag is set. Clearing a TXEx flag also clears the corresponding ABTAKx (see Section 12.3.9, "MSCAN Transmitter Message Abort Acknowledge Register (CANTAAK)"). When a TXEx flag is set, the corresponding ABTRQx bit is cleared (see Section 12.3.8, "MSCAN Transmitter Message Abort Request Register (CANTARQ)"). When listen-mode is active (see Section 12.3.2, "MSCAN Control Register 1 (CANCTL1)") the TXEx flags cannot be cleared and no transmission is started. Read and write accesses to the transmit buffer are blocked, if the corresponding TXEx bit is cleared (TXEx = 0) and the buffer is scheduled for transmission. 0 The associated message buffer is full (loaded with a message due for transmission) 1 The associated message buffer is empty (not scheduled) 12.3.7 MSCAN Transmitter Interrupt Enable Register (CANTIER) This register contains the interrupt enable bits for the transmit buffer empty interrupt flags. R 7 6 5 4 3 0 0 0 0 0 2 1 0 TXEIE2 TXEIE1 TXEIE0 0 0 0 W Reset: 0 0 0 0 0 = Unimplemented Figure 12-11. MSCAN Transmitter Interrupt Enable Register (CANTIER) MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 233 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) NOTE The CANTIER register is held in the reset state when the initialization mode is active (INITRQ = 1 and INITAK = 1). This register is writable when not in initialization mode (INITRQ = 0 and INITAK = 0). Read: Anytime Write: Anytime when not in initialization mode Table 12-12. CANTIER Register Field Descriptions Field Description 2:0 TXEIE[2:0] 12.3.8 Transmitter Empty Interrupt Enable 0 No interrupt request is generated from this event. 1 A transmitter empty (transmit buffer available for transmission) event causes a transmitter empty interrupt request. See Section 12.5.2.2, "Transmit Structures" for details. MSCAN Transmitter Message Abort Request Register (CANTARQ) The CANTARQ register allows abort request of messages queued for transmission. R 7 6 5 4 3 0 0 0 0 0 2 1 0 ABTRQ2 ABTRQ1 ABTRQ0 0 0 0 W Reset: 0 0 0 0 0 = Unimplemented Figure 12-12. MSCAN Transmitter Message Abort Request Register (CANTARQ) NOTE The CANTARQ register is held in the reset state when the initialization mode is active (INITRQ = 1 and INITAK = 1). This register is writable when not in initialization mode (INITRQ = 0 and INITAK = 0). Read: Anytime Write: Anytime when not in initialization mode Table 12-13. CANTARQ Register Field Descriptions Field Description 2:0 Abort Request -- The CPU sets the ABTRQx bit to request that a scheduled message buffer (TXEx = 0) be ABTRQ[2:0] aborted. The MSCAN grants the request if the message has not already started transmission, or if the transmission is not successful (lost arbitration or error). When a message is aborted, the associated TXE (see Section 12.3.6, "MSCAN Transmitter Flag Register (CANTFLG)") and abort acknowledge flags (ABTAK, see Section 12.3.9, "MSCAN Transmitter Message Abort Acknowledge Register (CANTAAK)") are set and a transmit interrupt occurs if enabled. The CPU cannot reset ABTRQx. ABTRQx is reset whenever the associated TXE flag is set. 0 No abort request 1 Abort request pending MC9S08DZ60 Series Data Sheet, Rev. 4 234 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) 12.3.9 MSCAN Transmitter Message Abort Acknowledge Register (CANTAAK) The CANTAAK register indicates the successful abort of messages queued for transmission, if requested by the appropriate bits in the CANTARQ register. R 7 6 5 4 3 2 1 0 0 0 0 0 0 ABTAK2 ABTAK1 ABTAK0 0 0 0 0 0 0 0 0 W Reset: = Unimplemented Figure 12-13. MSCAN Transmitter Message Abort Acknowledge Register (CANTAAK) NOTE The CANTAAK register is held in the reset state when the initialization mode is active (INITRQ = 1 and INITAK = 1). Read: Anytime Write: Unimplemented for ABTAKx flags Table 12-14. CANTAAK Register Field Descriptions Field Description 2:0 Abort Acknowledge -- This flag acknowledges that a message was aborted due to a pending transmission ABTAK[2:0] abort request from the CPU. After a particular message buffer is flagged empty, this flag can be used by the application software to identify whether the message was aborted successfully or was sent anyway. The ABTAKx flag is cleared whenever the corresponding TXE flag is cleared. 0 The message was not aborted. 1 The message was aborted. 12.3.10 MSCAN Transmit Buffer Selection Register (CANTBSEL) The CANTBSEL selections of the actual transmit message buffer, which is accessible in the CANTXFG register space. R 7 6 5 4 3 0 0 0 0 0 2 1 0 TX2 TX1 TX0 0 0 0 W Reset: 0 0 0 0 0 = Unimplemented Figure 12-14. MSCAN Transmit Buffer Selection Register (CANTBSEL) MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 235 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) NOTE The CANTBSEL register is held in the reset state when the initialization mode is active (INITRQ = 1 and INITAK=1). This register is writable when not in initialization mode (INITRQ = 0 and INITAK = 0). Read: Find the lowest ordered bit set to 1, all other bits will be read as 0 Write: Anytime when not in initialization mode Table 12-15. CANTBSEL Register Field Descriptions Field Description 2:0 TX[2:0] Transmit Buffer Select -- The lowest numbered bit places the respective transmit buffer in the CANTXFG register space (e.g., TX1 = 1 and TX0 = 1 selects transmit buffer TX0; TX1 = 1 and TX0 = 0 selects transmit buffer TX1). Read and write accesses to the selected transmit buffer will be blocked, if the corresponding TXEx bit is cleared and the buffer is scheduled for transmission (see Section 12.3.6, "MSCAN Transmitter Flag Register (CANTFLG)"). 0 The associated message buffer is deselected 1 The associated message buffer is selected, if lowest numbered bit The following gives a short programming example of the usage of the CANTBSEL register: To get the next available transmit buffer, application software must read the CANTFLG register and write this value back into the CANTBSEL register. In this example Tx buffers TX1 and TX2 are available. The value read from CANTFLG is therefore 0b0000_0110. When writing this value back to CANTBSEL, the Tx buffer TX1 is selected in the CANTXFG because the lowest numbered bit set to 1 is at bit position 1. Reading back this value out of CANTBSEL results in 0b0000_0010, because only the lowest numbered bit position set to 1 is presented. This mechanism eases the application software the selection of the next available Tx buffer. * LDD CANTFLG; value read is 0b0000_0110 * STD CANTBSEL; value written is 0b0000_0110 * LDD CANTBSEL; value read is 0b0000_0010 If all transmit message buffers are deselected, no accesses are allowed to the CANTXFG buffer register. 12.3.11 MSCAN Identifier Acceptance Control Register (CANIDAC) The CANIDAC register is used for identifier filter acceptance control as described below. R 7 6 0 0 5 4 IDAM1 IDAM0 0 0 3 2 1 0 0 IDHIT2 IDHIT1 IDHIT0 0 0 0 0 W Reset: 0 0 = Unimplemented Figure 12-15. MSCAN Identifier Acceptance Control Register (CANIDAC) MC9S08DZ60 Series Data Sheet, Rev. 4 236 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) Read: Anytime Write: Anytime in initialization mode (INITRQ = 1 and INITAK = 1), except bits IDHITx, which are read-only Table 12-16. CANIDAC Register Field Descriptions Field Description 5:4 IDAM[1:0] Identifier Acceptance Mode -- The CPU sets these flags to define the identifier acceptance filter organization (see Section 12.5.3, "Identifier Acceptance Filter"). Table 12-17 summarizes the different settings. In filter closed mode, no message is accepted such that the foreground buffer is never reloaded. 2:0 IDHIT[2:0] Identifier Acceptance Hit Indicator -- The MSCAN sets these flags to indicate an identifier acceptance hit (see Section 12.5.3, "Identifier Acceptance Filter"). Table 12-18 summarizes the different settings. Table 12-17. Identifier Acceptance Mode Settings IDAM1 IDAM0 Identifier Acceptance Mode 0 0 Two 32-bit acceptance filters 0 1 Four 16-bit acceptance filters 1 0 Eight 8-bit acceptance filters 1 1 Filter closed Table 12-18. Identifier Acceptance Hit Indication IDHIT2 IDHIT1 IDHIT0 Identifier Acceptance Hit 0 0 0 Filter 0 hit 0 0 1 Filter 1 hit 0 1 0 Filter 2 hit 0 1 1 Filter 3 hit 1 0 0 Filter 4 hit 1 0 1 Filter 5 hit 1 1 0 Filter 6 hit 1 1 1 Filter 7 hit The IDHITx indicators are always related to the message in the foreground buffer (RxFG). When a message gets shifted into the foreground buffer of the receiver FIFO the indicators are updated as well. 12.3.12 MSCAN Miscellaneous Register (CANMISC) This register provides additional features. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 237 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 BOHOLD W Reset: 0 0 0 0 0 0 0 0 = Unimplemented Figure 12-16. MSCAN Miscellaneous Register (CANMISC) Read: Anytime Write: Anytime; write of `1' clears flag; write of `0' ignored Table 12-19. CANMISC Register Field Descriptions Field Description 0 BOHOLD Bus-off State Hold Until User Request -- If BORM is set in Section 12.3.2, "MSCAN Control Register 1 (CANCTL1), this bit indicates whether the module has entered the bus-off state. Clearing this bit requests the recovery from bus-off. Refer to Section 12.6.2, "Bus-Off Recovery," for details. 0 Module is not bus-off or recovery has been requested by user in bus-off state 1 Module is bus-off and holds this state until user request 12.3.13 MSCAN Receive Error Counter (CANRXERR) This register reflects the status of the MSCAN receive error counter. R 7 6 5 4 3 2 1 0 RXERR7 RXERR6 RXERR5 RXERR4 RXERR3 RXERR2 RXERR1 RXERR0 0 0 0 0 0 0 0 0 W Reset: = Unimplemented Figure 12-17. MSCAN Receive Error Counter (CANRXERR) Read: Only when in sleep mode (SLPRQ = 1 and SLPAK = 1) or initialization mode (INITRQ = 1 and INITAK = 1) Write: Unimplemented NOTE Reading this register when in any other mode other than sleep or initialization mode may return an incorrect value. For MCUs with dual CPUs, this may result in a CPU fault condition. Writing to this register when in special modes can alter the MSCAN functionality. MC9S08DZ60 Series Data Sheet, Rev. 4 238 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) 12.3.14 MSCAN Transmit Error Counter (CANTXERR) This register reflects the status of the MSCAN transmit error counter. R 7 6 5 4 3 2 1 0 TXERR7 TXERR6 TXERR5 TXERR4 TXERR3 TXERR2 TXERR1 TXERR0 0 0 0 0 0 0 0 0 W Reset: = Unimplemented Figure 12-18. MSCAN Transmit Error Counter (CANTXERR) Read: Only when in sleep mode (SLPRQ = 1 and SLPAK = 1) or initialization mode (INITRQ = 1 and INITAK = 1) Write: Unimplemented NOTE Reading this register when in any other mode other than sleep or initialization mode, may return an incorrect value. For MCUs with dual CPUs, this may result in a CPU fault condition. Writing to this register when in special modes can alter the MSCAN functionality. 12.3.15 MSCAN Identifier Acceptance Registers (CANIDAR0-7) On reception, each message is written into the background receive buffer. The CPU is only signalled to read the message if it passes the criteria in the identifier acceptance and identifier mask registers (accepted); otherwise, the message is overwritten by the next message (dropped). The acceptance registers of the MSCAN are applied on the IDR0-IDR3 registers (see Section 12.4.1, "Identifier Registers (IDR0-IDR3)") of incoming messages in a bit by bit manner (see Section 12.5.3, "Identifier Acceptance Filter"). For extended identifiers, all four acceptance and mask registers are applied. For standard identifiers, only the first two (CANIDAR0/1, CANIDMR0/1) are applied. R W Reset 7 6 5 4 3 2 1 0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 0 0 0 0 0 0 0 0 Figure 12-19. MSCAN Identifier Acceptance Registers (First Bank) -- CANIDAR0-CANIDAR3 Read: Anytime Write: Anytime in initialization mode (INITRQ = 1 and INITAK = 1) MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 239 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) Table 12-20. CANIDAR0-CANIDAR3 Register Field Descriptions Field Description 7:0 AC[7:0] Acceptance Code Bits -- AC[7:0] comprise a user-defined sequence of bits with which the corresponding bits of the related identifier register (IDRn) of the receive message buffer are compared. The result of this comparison is then masked with the corresponding identifier mask register. R W Reset 7 6 5 4 3 2 1 0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 0 0 0 0 0 0 0 0 Figure 12-20. MSCAN Identifier Acceptance Registers (Second Bank) -- CANIDAR4-CANIDAR7 Read: Anytime Write: Anytime in initialization mode (INITRQ = 1 and INITAK = 1) Table 12-21. CANIDAR4-CANIDAR7 Register Field Descriptions Field Description 7:0 AC[7:0] Acceptance Code Bits -- AC[7:0] comprise a user-defined sequence of bits with which the corresponding bits of the related identifier register (IDRn) of the receive message buffer are compared. The result of this comparison is then masked with the corresponding identifier mask register. 12.3.16 MSCAN Identifier Mask Registers (CANIDMR0-CANIDMR7) The identifier mask register specifies which of the corresponding bits in the identifier acceptance register are relevant for acceptance filtering. To receive standard identifiers in 32 bit filter mode, it is required to program the last three bits (AM[2:0]) in the mask registers CANIDMR1 and CANIDMR5 to "don't care." To receive standard identifiers in 16 bit filter mode, it is required to program the last three bits (AM[2:0]) in the mask registers CANIDMR1, CANIDMR3, CANIDMR5, and CANIDMR7 to "don't care." R W Reset 7 6 5 4 3 2 1 0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 0 0 0 0 0 0 0 0 Figure 12-21. MSCAN Identifier Mask Registers (First Bank) -- CANIDMR0-CANIDMR3 Read: Anytime Write: Anytime in initialization mode (INITRQ = 1 and INITAK = 1) MC9S08DZ60 Series Data Sheet, Rev. 4 240 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) Table 12-22. CANIDMR0-CANIDMR3 Register Field Descriptions Field Description 7:0 AM[7:0] Acceptance Mask Bits -- If a particular bit in this register is cleared, this indicates that the corresponding bit in the identifier acceptance register must be the same as its identifier bit before a match is detected. The message is accepted if all such bits match. If a bit is set, it indicates that the state of the corresponding bit in the identifier acceptance register does not affect whether or not the message is accepted. 0 Match corresponding acceptance code register and identifier bits 1 Ignore corresponding acceptance code register bit (don't care) R W Reset 7 6 5 4 3 2 1 0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 0 0 0 0 0 0 0 0 Figure 12-22. MSCAN Identifier Mask Registers (Second Bank) -- CANIDMR4-CANIDMR7 Read: Anytime Write: Anytime in initialization mode (INITRQ = 1 and INITAK = 1) Table 12-23. CANIDMR4-CANIDMR7 Register Field Descriptions Field Description 7:0 AM[7:0] Acceptance Mask Bits -- If a particular bit in this register is cleared, this indicates that the corresponding bit in the identifier acceptance register must be the same as its identifier bit before a match is detected. The message is accepted if all such bits match. If a bit is set, it indicates that the state of the corresponding bit in the identifier acceptance register does not affect whether or not the message is accepted. 0 Match corresponding acceptance code register and identifier bits 1 Ignore corresponding acceptance code register bit (don't care) 12.4 Programmer's Model of Message Storage The following section details the organization of the receive and transmit message buffers and the associated control registers. To simplify the programmer interface, the receive and transmit message buffers have the same outline. Each message buffer allocates 16 bytes in the memory map containing a 13 byte data structure. An additional transmit buffer priority register (TBPR) is defined for the transmit buffers. Within the last two bytes of this memory map, the MSCAN stores a special 16-bit time stamp, which is sampled from an internal timer after successful transmission or reception of a message. This feature is only available for transmit and receiver buffers if the TIME bit is set (see Section 12.3.1, "MSCAN Control Register 0 (CANCTL0)"). The time stamp register is written by the MSCAN. The CPU can only read these registers. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 241 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) Table 12-24. Message Buffer Organization Offset Address Register 0x00X0 Identifier Register 0 0x00X1 Identifier Register 1 0x00X2 Identifier Register 2 0x00X3 Identifier Register 3 0x00X4 Data Segment Register 0 0x00X5 Data Segment Register 1 0x00X6 Data Segment Register 2 0x00X7 Data Segment Register 3 0x00X8 Data Segment Register 4 0x00X9 Data Segment Register 5 0x00XA Data Segment Register 6 0x00XB Data Segment Register 7 0x00XC Data Length Register 0x00XD Transmit Buffer Priority Register1 0x00XE Time Stamp Register (High Byte)2 0x00XF Time Stamp Register (Low Byte)3 Access 1 Not applicable for receive buffers Read-only for CPU 3 Read-only for CPU 2 Figure 12-23 shows the common 13-byte data structure of receive and transmit buffers for extended identifiers. The mapping of standard identifiers into the IDR registers is shown in Figure 12-24. All bits of the receive and transmit buffers are `x' out of reset because of RAM-based implementation1. All reserved or unused bits of the receive and transmit buffers always read `x'. 1. Exception: The transmit priority registers are 0 out of reset. MC9S08DZ60 Series Data Sheet, Rev. 4 242 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) Register Name IDR0 IDR1 R W R W R IDR2 W IDR3 W R R DSR0 W R DSR1 W R DSR2 W DSR3 W R R DSR4 W R DSR5 W DSR6 W R R DSR7 W Bit 7 6 5 4 3 2 1 Bit0 ID28 ID27 ID26 ID25 ID24 ID23 ID22 ID21 ID20 ID19 ID18 SRR(1) IDE(1) ID17 ID16 ID15 ID14 ID13 ID12 ID11 ID10 ID9 ID8 ID7 ID6 ID5 ID4 ID3 ID2 ID1 ID0 RTR2 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DLC3 DLC2 DLC1 DLC0 R DLR W = Unused, always read `x' Figure 12-23. Receive/Transmit Message Buffer -- Extended Identifier Mapping 1 2 SRR and IDE are both 1s. The position of RTR differs between extended and standard indentifier mapping. Read: For transmit buffers, anytime when TXEx flag is set (see Section 12.3.6, "MSCAN Transmitter Flag Register (CANTFLG)") and the corresponding transmit buffer is selected in CANTBSEL (see MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 243 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) Section 12.3.10, "MSCAN Transmit Buffer Selection Register (CANTBSEL)"). For receive buffers, only when RXF flag is set (see Section 12.3.4.1, "MSCAN Receiver Flag Register (CANRFLG)"). Write: For transmit buffers, anytime when TXEx flag is set (see Section 12.3.6, "MSCAN Transmitter Flag Register (CANTFLG)") and the corresponding transmit buffer is selected in CANTBSEL (see Section 12.3.10, "MSCAN Transmit Buffer Selection Register (CANTBSEL)"). Unimplemented for receive buffers. Reset: Undefined (0x00XX) because of RAM-based implementation Register Name R IDR0 W R IDR1 W Bit 7 6 5 4 3 2 1 Bit 0 ID10 ID9 ID8 ID7 ID6 ID5 ID4 ID3 ID2 ID1 ID0 RTR1 IDE2 R IDR2 W R IDR3 W = Unused, always read `x' Figure 12-24. Receive/Transmit Message Buffer -- Standard Identifier Mapping 1 2 The position of RTR differs between extended and standard indentifier mapping. IDE is 0. 12.4.1 Identifier Registers (IDR0-IDR3) The identifier registers for an extended format identifier consist of a total of 32 bits; ID[28:0], SRR, IDE, and RTR bits. The identifier registers for a standard format identifier consist of a total of 13 bits; ID[10:0], RTR, and IDE bits. 12.4.1.1 IDR0-IDR3 for Extended Identifier Mapping 7 6 5 4 3 2 1 0 ID28 ID27 ID26 ID25 ID24 ID23 ID22 ID21 x x x x x x x x R W Reset: Figure 12-25. Identifier Register 0 (IDR0) -- Extended Identifier Mapping MC9S08DZ60 Series Data Sheet, Rev. 4 244 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) Table 12-25. IDR0 Register Field Descriptions -- Extended Field Description 7:0 ID[28:21] Extended Format Identifier -- The identifiers consist of 29 bits (ID[28:0]) for the extended format. ID28 is the most significant bit and is transmitted first on the CAN bus during the arbitration procedure. The priority of an identifier is defined to be highest for the smallest binary number. 7 6 5 4 3 2 1 0 ID20 ID19 ID18 SRR(1) IDE(1) ID17 ID16 ID15 x x x x x x x x R W Reset: Figure 12-26. Identifier Register 1 (IDR1) -- Extended Identifier Mapping 1 SRR and IDE are both 1s. Table 12-26. IDR1 Register Field Descriptions -- Extended Field Description 7:5 ID[20:18] Extended Format Identifier -- The identifiers consist of 29 bits (ID[28:0]) for the extended format. ID28 is the most significant bit and is transmitted first on the CAN bus during the arbitration procedure. The priority of an identifier is defined to be highest for the smallest binary number. 4 SRR Substitute Remote Request -- This fixed recessive bit is used only in extended format. It must be set to 1 by the user for transmission buffers and is stored as received on the CAN bus for receive buffers. 3 IDE ID Extended -- This flag indicates whether the extended or standard identifier format is applied in this buffer. In the case of a receive buffer, the flag is set as received and indicates to the CPU how to process the buffer identifier registers. In the case of a transmit buffer, the flag indicates to the MSCAN what type of identifier to send. 0 Standard format (11 bit) 1 Extended format (29 bit) 2:0 ID[17:15] Extended Format Identifier -- The identifiers consist of 29 bits (ID[28:0]) for the extended format. ID28 is the most significant bit and is transmitted first on the CAN bus during the arbitration procedure. The priority of an identifier is defined to be highest for the smallest binary number. 7 6 5 4 3 2 1 0 ID14 ID13 ID12 ID11 ID10 ID9 ID8 ID7 x x x x x x x x R W Reset: Figure 12-27. Identifier Register 2 (IDR2) -- Extended Identifier Mapping Table 12-27. IDR2 Register Field Descriptions -- Extended Field Description 7:0 ID[14:7] Extended Format Identifier -- The identifiers consist of 29 bits (ID[28:0]) for the extended format. ID28 is the most significant bit and is transmitted first on the CAN bus during the arbitration procedure. The priority of an identifier is defined to be highest for the smallest binary number. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 245 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) 7 6 5 4 3 2 1 0 ID6 ID5 ID4 ID3 ID2 ID1 ID0 RTR x x x x x x x x R W Reset: Figure 12-28. Identifier Register 3 (IDR3) -- Extended Identifier Mapping Table 12-28. IDR3 Register Field Descriptions -- Extended Field Description 7:1 ID[6:0] Extended Format Identifier -- The identifiers consist of 29 bits (ID[28:0]) for the extended format. ID28 is the most significant bit and is transmitted first on the CAN bus during the arbithation procedure. The priority of an identifier is defined to be highest for the smallest binary number. 0 RTR Remote Transmission Request -- This flag reflects the status of the remote transmission request bit in the CAN frame. In the case of a receive buffer, it indicates the status of the received frame and supports the transmission of an answering frame in software. In the case of a transmit buffer, this flag defines the setting of the RTR bit to be sent. 0 Data frame 1 Remote frame 12.4.2 IDR0-IDR3 for Standard Identifier Mapping 7 6 5 4 3 2 1 0 ID10 ID9 ID8 ID7 ID6 ID5 ID4 ID3 x x x x x x x x R W Reset: Figure 12-29. Identifier Register 0 -- Standard Mapping Table 12-29. IDR0 Register Field Descriptions -- Standard Field Description 7:0 ID[10:3] Standard Format Identifier -- The identifiers consist of 11 bits (ID[10:0]) for the standard format. ID10 is the most significant bit and is transmitted first on the CAN bus during the arbitration procedure. The priority of an identifier is defined to be highest for the smallest binary number. See also ID bits in Table 12-30. 7 6 5 4 3 ID2 ID1 ID0 RTR IDE(1) x x x x x R 2 1 0 x x x W Reset: = Unused; always read `x' Figure 12-30. Identifier Register 1 -- Standard Mapping 1 IDE is 0. MC9S08DZ60 Series Data Sheet, Rev. 4 246 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) Table 12-30. IDR1 Register Field Descriptions Field Description 7:5 ID[2:0] Standard Format Identifier -- The identifiers consist of 11 bits (ID[10:0]) for the standard format. ID10 is the most significant bit and is transmitted first on the CAN bus during the arbitration procedure. The priority of an identifier is defined to be highest for the smallest binary number. See also ID bits in Table 12-29. 4 RTR Remote Transmission Request -- This flag reflects the status of the Remote Transmission Request bit in the CAN frame. In the case of a receive buffer, it indicates the status of the received frame and supports the transmission of an answering frame in software. In the case of a transmit buffer, this flag defines the setting of the RTR bit to be sent. 0 Data frame 1 Remote frame 3 IDE ID Extended -- This flag indicates whether the extended or standard identifier format is applied in this buffer. In the case of a receive buffer, the flag is set as received and indicates to the CPU how to process the buffer identifier registers. In the case of a transmit buffer, the flag indicates to the MSCAN what type of identifier to send. 0 Standard format (11 bit) 1 Extended format (29 bit) 7 6 5 4 3 2 1 0 x x x x x x x x R W Reset: = Unused; always read `x' Figure 12-31. Identifier Register 2 -- Standard Mapping 7 6 5 4 3 2 1 0 x x x x x x x x R W Reset: = Unused; always read `x' Figure 12-32. Identifier Register 3 -- Standard Mapping 12.4.3 Data Segment Registers (DSR0-7) The eight data segment registers, each with bits DB[7:0], contain the data to be transmitted or received. The number of bytes to be transmitted or received is determined by the data length code in the corresponding DLR register. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 247 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) 7 6 5 4 3 2 1 0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 x x x x x x x x R W Reset: Figure 12-33. Data Segment Registers (DSR0-DSR7) -- Extended Identifier Mapping Table 12-31. DSR0-DSR7 Register Field Descriptions Field Description 7:0 DB[7:0] Data bits 7:0 12.4.4 Data Length Register (DLR) This register keeps the data length field of the CAN frame. 7 6 5 4 3 2 1 0 DLC3 DLC2 DLC1 DLC0 x x x x R W Reset: x x x x = Unused; always read "x" Figure 12-34. Data Length Register (DLR) -- Extended Identifier Mapping Table 12-32. DLR Register Field Descriptions Field Description 3:0 DLC[3:0] Data Length Code Bits -- The data length code contains the number of bytes (data byte count) of the respective message. During the transmission of a remote frame, the data length code is transmitted as programmed while the number of transmitted data bytes is always 0. The data byte count ranges from 0 to 8 for a data frame. Table 12-33 shows the effect of setting the DLC bits. MC9S08DZ60 Series Data Sheet, Rev. 4 248 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) Table 12-33. Data Length Codes Data Length Code 12.4.5 DLC3 DLC2 DLC1 DLC0 Data Byte Count 0 0 0 0 0 0 0 0 1 1 0 0 1 0 2 0 0 1 1 3 0 1 0 0 4 0 1 0 1 5 0 1 1 0 6 0 1 1 1 7 1 0 0 0 8 Transmit Buffer Priority Register (TBPR) This register defines the local priority of the associated message transmit buffer. The local priority is used for the internal prioritization process of the MSCAN and is defined to be highest for the smallest binary number. The MSCAN implements the following internal prioritization mechanisms: * All transmission buffers with a cleared TXEx flag participate in the prioritization immediately before the SOF (start of frame) is sent. * The transmission buffer with the lowest local priority field wins the prioritization. In cases of more than one buffer having the same lowest priority, the message buffer with the lower index number wins. 7 6 5 4 3 2 1 0 PRIO7 PRIO6 PRIO5 PRIO4 PRIO3 PRIO2 PRIO1 PRIO0 0 0 0 0 0 0 0 0 R W Reset: Figure 12-35. Transmit Buffer Priority Register (TBPR) Read: Anytime when TXEx flag is set (see Section 12.3.6, "MSCAN Transmitter Flag Register (CANTFLG)") and the corresponding transmit buffer is selected in CANTBSEL (see Section 12.3.10, "MSCAN Transmit Buffer Selection Register (CANTBSEL)"). Write: Anytime when TXEx flag is set (see Section 12.3.6, "MSCAN Transmitter Flag Register (CANTFLG)") and the corresponding transmit buffer is selected in CANTBSEL (see Section 12.3.10, "MSCAN Transmit Buffer Selection Register (CANTBSEL)"). 12.4.6 Time Stamp Register (TSRH-TSRL) If the TIME bit is enabled, the MSCAN will write a time stamp to the respective registers in the active transmit or receive buffer as soon as a message has been acknowledged on the CAN bus (see MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 249 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) Section 12.3.1, "MSCAN Control Register 0 (CANCTL0)"). In case of a transmission, the CPU can only read the time stamp after the respective transmit buffer has been flagged empty. The timer value, which is used for stamping, is taken from a free running internal CAN bit clock. A timer overrun is not indicated by the MSCAN. The timer is reset (all bits set to 0) during initialization mode. The CPU can only read the time stamp registers. R 7 6 5 4 3 2 1 0 TSR15 TSR14 TSR13 TSR12 TSR11 TSR10 TSR9 TSR8 x x x x x x x x W Reset: Figure 12-36. Time Stamp Register -- High Byte (TSRH) R 7 6 5 4 3 2 1 0 TSR7 TSR6 TSR5 TSR4 TSR3 TSR2 TSR1 TSR0 x x x x x x x x W Reset: Figure 12-37. Time Stamp Register -- Low Byte (TSRL) Read: Anytime when TXEx flag is set (see Section 12.3.6, "MSCAN Transmitter Flag Register (CANTFLG)") and the corresponding transmit buffer is selected in CANTBSEL (see Section 12.3.10, "MSCAN Transmit Buffer Selection Register (CANTBSEL)"). Write: Unimplemented 12.5 12.5.1 Functional Description General This section provides a complete functional description of the MSCAN. It describes each of the features and modes listed in the introduction. MC9S08DZ60 Series Data Sheet, Rev. 4 250 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) 12.5.2 Message Storage CAN Receive / Transmit Engine CPU12 Memory Mapped I/O Rx0 RXF CPU bus RxFG RxBG MSCAN Rx1 Rx2 Rx3 Rx4 Receiver TxBG Tx0 MSCAN TxFG Tx1 Transmitter TxBG Tx2 TXE0 PRIO TXE1 CPU bus PRIO TXE2 PRIO Figure 12-38. User Model for Message Buffer Organization MSCAN facilitates a sophisticated message storage system which addresses the requirements of a broad range of network applications. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 251 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) 12.5.2.1 Message Transmit Background Modern application layer software is built upon two fundamental assumptions: * Any CAN node is able to send out a stream of scheduled messages without releasing the CAN bus between the two messages. Such nodes arbitrate for the CAN bus immediately after sending the previous message and only release the CAN bus in case of lost arbitration. * The internal message queue within any CAN node is organized such that the highest priority message is sent out first, if more than one message is ready to be sent. The behavior described in the bullets above cannot be achieved with a single transmit buffer. That buffer must be reloaded immediately after the previous message is sent. This loading process lasts a finite amount of time and must be completed within the inter-frame sequence (IFS) to be able to send an uninterrupted stream of messages. Even if this is feasible for limited CAN bus speeds, it requires that the CPU reacts with short latencies to the transmit interrupt. A double buffer scheme de-couples the reloading of the transmit buffer from the actual message sending and, therefore, reduces the reactiveness requirements of the CPU. Problems can arise if the sending of a message is finished while the CPU re-loads the second buffer. No buffer would then be ready for transmission, and the CAN bus would be released. At least three transmit buffers are required to meet the first of the above requirements under all circumstances. The MSCAN has three transmit buffers. The second requirement calls for some sort of internal prioritization which the MSCAN implements with the "local priority" concept described in Section 12.5.2.2, "Transmit Structures." 12.5.2.2 Transmit Structures The MSCAN triple transmit buffer scheme optimizes real-time performance by allowing multiple messages to be set up in advance. The three buffers are arranged as shown in Figure 12-38. All three buffers have a 13-byte data structure similar to the outline of the receive buffers (see Section 12.4, "Programmer's Model of Message Storage"). An additional Section 12.4.5, "Transmit Buffer Priority Register (TBPR) contains an 8-bit local priority field (PRIO) (see Section 12.4.5, "Transmit Buffer Priority Register (TBPR)"). The remaining two bytes are used for time stamping of a message, if required (see Section 12.4.6, "Time Stamp Register (TSRH-TSRL)"). To transmit a message, the CPU must identify an available transmit buffer, which is indicated by a set transmitter buffer empty (TXEx) flag (see Section 12.3.6, "MSCAN Transmitter Flag Register (CANTFLG)"). If a transmit buffer is available, the CPU must set a pointer to this buffer by writing to the CANTBSEL register (see Section 12.3.10, "MSCAN Transmit Buffer Selection Register (CANTBSEL)"). This makes the respective buffer accessible within the CANTXFG address space (see Section 12.4, "Programmer's Model of Message Storage"). The algorithmic feature associated with the CANTBSEL register simplifies the transmit buffer selection. In addition, this scheme makes the handler software simpler because only one address area is applicable for the transmit process, and the required address space is minimized. The CPU then stores the identifier, the control bits, and the data content into one of the transmit buffers. Finally, the buffer is flagged as ready for transmission by clearing the associated TXE flag. MC9S08DZ60 Series Data Sheet, Rev. 4 252 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) The MSCAN then schedules the message for transmission and signals the successful transmission of the buffer by setting the associated TXE flag. A transmit interrupt (see Section 12.5.7.2, "Transmit Interrupt") is generated1 when TXEx is set and can be used to drive the application software to re-load the buffer. If more than one buffer is scheduled for transmission when the CAN bus becomes available for arbitration, the MSCAN uses the local priority setting of the three buffers to determine the prioritization. For this purpose, every transmit buffer has an 8-bit local priority field (PRIO). The application software programs this field when the message is set up. The local priority reflects the priority of this particular message relative to the set of messages being transmitted from this node. The lowest binary value of the PRIO field is defined to be the highest priority. The internal scheduling process takes place whenever the MSCAN arbitrates for the CAN bus. This is also the case after the occurrence of a transmission error. When a high priority message is scheduled by the application software, it may become necessary to abort a lower priority message in one of the three transmit buffers. Because messages that are already in transmission cannot be aborted, the user must request the abort by setting the corresponding abort request bit (ABTRQ) (see Section 12.3.8, "MSCAN Transmitter Message Abort Request Register (CANTARQ)".) The MSCAN then grants the request, if possible, by: 1. Setting the corresponding abort acknowledge flag (ABTAK) in the CANTAAK register. 2. Setting the associated TXE flag to release the buffer. 3. Generating a transmit interrupt. The transmit interrupt handler software can determine from the setting of the ABTAK flag whether the message was aborted (ABTAK = 1) or sent (ABTAK = 0). 12.5.2.3 Receive Structures The received messages are stored in a five stage input FIFO. The five message buffers are alternately mapped into a single memory area (see Figure 12-38). The background receive buffer (RxBG) is exclusively associated with the MSCAN, but the foreground receive buffer (RxFG) is addressable by the CPU (see Figure 12-38). This scheme simplifies the handler software because only one address area is applicable for the receive process. All receive buffers have a size of 15 bytes to store the CAN control bits, the identifier (standard or extended), the data contents, and a time stamp, if enabled (see Section 12.4, "Programmer's Model of Message Storage"). The receiver full flag (RXF) (see Section 12.3.4.1, "MSCAN Receiver Flag Register (CANRFLG)") signals the status of the foreground receive buffer. When the buffer contains a correctly received message with a matching identifier, this flag is set. On reception, each message is checked to see whether it passes the filter (see Section 12.5.3, "Identifier Acceptance Filter") and simultaneously is written into the active RxBG. After successful reception of a valid message, the MSCAN shifts the content of RxBG into the receiver FIFO2, sets the RXF flag, and generates a receive interrupt (see Section 12.5.7.3, "Receive Interrupt") to the CPU3. The user's receive handler must read the received message from the RxFG and then reset the RXF flag to acknowledge the interrupt and to release the foreground buffer. A new message, which can follow immediately after the IFS 1. The transmit interrupt occurs only if not masked. A polling scheme can be applied on TXEx also. 2. Only if the RXF flag is not set. 3. The receive interrupt occurs only if not masked. A polling scheme can be applied on RXF also. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 253 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) field of the CAN frame, is received into the next available RxBG. If the MSCAN receives an invalid message in its RxBG (wrong identifier, transmission errors, etc.) the actual contents of the buffer will be over-written by the next message. The buffer will then not be shifted into the FIFO. When the MSCAN module is transmitting, the MSCAN receives its own transmitted messages into the background receive buffer, RxBG, but does not shift it into the receiver FIFO, generate a receive interrupt, or acknowledge its own messages on the CAN bus. The exception to this rule is in loopback mode (see Section 12.3.2, "MSCAN Control Register 1 (CANCTL1)") where the MSCAN treats its own messages exactly like all other incoming messages. The MSCAN receives its own transmitted messages in the event that it loses arbitration. If arbitration is lost, the MSCAN must be prepared to become a receiver. An overrun condition occurs when all receive message buffers in the FIFO are filled with correctly received messages with accepted identifiers and another message is correctly received from the CAN bus with an accepted identifier. The latter message is discarded and an error interrupt with overrun indication is generated if enabled (see Section 12.5.7.5, "Error Interrupt"). The MSCAN remains able to transmit messages while the receiver FIFO is full, but all incoming messages are discarded. As soon as a receive buffer in the FIFO is available again, new valid messages will be accepted. 12.5.3 Identifier Acceptance Filter The MSCAN identifier acceptance registers (see Section 12.3.11, "MSCAN Identifier Acceptance Control Register (CANIDAC)") define the acceptable patterns of the standard or extended identifier (ID[10:0] or ID[28:0]). Any of these bits can be marked `don't care' in the MSCAN identifier mask registers (see Section 12.3.16, "MSCAN Identifier Mask Registers (CANIDMR0-CANIDMR7)"). A filter hit is indicated to the application software by a set receive buffer full flag (RXF = 1) and three bits in the CANIDAC register (see Section 12.3.11, "MSCAN Identifier Acceptance Control Register (CANIDAC)"). These identifier hit flags (IDHIT[2:0]) clearly identify the filter section that caused the acceptance. They simplify the application software's task to identify the cause of the receiver interrupt. If more than one hit occurs (two or more filters match), the lower hit has priority. A very flexible programmable generic identifier acceptance filter has been introduced to reduce the CPU interrupt loading. The filter is programmable to operate in four different modes (see Bosch CAN 2.0A/B protocol specification): * Two identifier acceptance filters, each to be applied to: -- The full 29 bits of the extended identifier and to the following bits of the CAN 2.0B frame: - Remote transmission request (RTR) - Identifier extension (IDE) - Substitute remote request (SRR) -- The 11 bits of the standard identifier plus the RTR and IDE bits of the CAN 2.0A/B messages1. This mode implements two filters for a full length CAN 2.0B compliant extended identifier. Figure 12-39 shows how the first 32-bit filter bank (CANIDAR0-CANIDAR3, CANIDMR0-CANIDMR3) produces a filter 0 hit. Similarly, the second filter bank (CANIDAR4-CANIDAR7, CANIDMR4-CANIDMR7) produces a filter 1 hit. 1.Although this mode can be used for standard identifiers, it is recommended to use the four or eight identifier acceptance filters for standard identifiers MC9S08DZ60 Series Data Sheet, Rev. 4 254 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) * * * Four identifier acceptance filters, each to be applied to -- a) the 14 most significant bits of the extended identifier plus the SRR and IDE bits of CAN 2.0B messages or -- b) the 11 bits of the standard identifier, the RTR and IDE bits of CAN 2.0A/B messages. Figure 12-40 shows how the first 32-bit filter bank (CANIDAR0-CANIDA3, CANIDMR0-3CANIDMR) produces filter 0 and 1 hits. Similarly, the second filter bank (CANIDAR4-CANIDAR7, CANIDMR4-CANIDMR7) produces filter 2 and 3 hits. Eight identifier acceptance filters, each to be applied to the first 8 bits of the identifier. This mode implements eight independent filters for the first 8 bits of a CAN 2.0A/B compliant standard identifier or a CAN 2.0B compliant extended identifier. Figure 12-41 shows how the first 32-bit filter bank (CANIDAR0-CANIDAR3, CANIDMR0-CANIDMR3) produces filter 0 to 3 hits. Similarly, the second filter bank (CANIDAR4-CANIDAR7, CANIDMR4-CANIDMR7) produces filter 4 to 7 hits. Closed filter. No CAN message is copied into the foreground buffer RxFG, and the RXF flag is never set. CAN 2.0B Extended Identifier ID28 IDR0 ID21 ID20 IDR1 CAN 2.0A/B Standard Identifier ID10 IDR0 ID3 ID2 IDR1 ID15 IDE ID14 IDR2 ID7 ID6 IDR3 RTR ID10 IDR2 ID3 ID10 IDR3 ID3 AM7 CANIDMR0 AM0 AM7 CANIDMR1 AM0 AM7 CANIDMR2 AM0 AM7 CANIDMR3 AM0 AC7 CANIDAR0 AC0 AC7 CANIDAR1 AC0 AC7 CANIDAR2 AC0 AC7 CANIDAR3 AC0 ID Accepted (Filter 0 Hit) Figure 12-39. 32-bit Maskable Identifier Acceptance Filter MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 255 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) CAN 2.0B Extended Identifier ID28 IDR0 ID21 ID20 IDR1 CAN 2.0A/B Standard Identifier ID10 IDR0 ID3 ID2 IDR1 AM7 CANIDMR0 AM0 AM7 CANIDMR1 AM0 AC7 CANIDAR0 AC0 AC7 CANIDAR1 AC0 ID15 IDE ID14 IDR2 ID7 ID6 IDR3 RTR ID10 IDR2 ID3 ID10 IDR3 ID3 ID Accepted (Filter 0 Hit) AM7 CANIDMR2 AM0 AM7 CANIDMR3 AM0 AC7 CANIDAR2 AC0 AC7 CANIDAR3 AC0 ID Accepted (Filter 1 Hit) Figure 12-40. 16-bit Maskable Identifier Acceptance Filters MC9S08DZ60 Series Data Sheet, Rev. 4 256 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) CAN 2.0B Extended Identifier ID28 IDR0 ID21 ID20 IDR1 CAN 2.0A/B Standard Identifier ID10 IDR0 ID3 ID2 IDR1 AM7 CIDMR0 AM0 AC7 CIDAR0 AC0 ID15 IDE ID14 IDR2 ID7 ID6 IDR3 RTR ID10 IDR2 ID3 ID10 IDR3 ID3 ID Accepted (Filter 0 Hit) AM7 CIDMR1 AM0 AC7 CIDAR1 AC0 ID Accepted (Filter 1 Hit) AM7 CIDMR2 AM0 AC7 CIDAR2 AC0 ID Accepted (Filter 2 Hit) AM7 CIDMR3 AM0 AC7 CIDAR3 AC0 ID Accepted (Filter 3 Hit) Figure 12-41. 8-bit Maskable Identifier Acceptance Filters MSCAN filter uses three sets of registers to provide the filter configuration. Firstly, the CANIDAC register determines the configuration of the banks into filter sizes and number of filters. Secondly, registers CANIDMR0/1/2/3 determine those bits on which the filter will operate by placing a `0' at the appropriate MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 257 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) bit position in the filter register. Finally, registers CANIDAR0/1/2/3 determine the value of those bits determined by CANIDMR0/1/2/3. For instance in the case of the filter value of: 0001x1001x0 The CANIDMR0/1/2/3 register would be configured as: 00001000010 and so all message identifier bits except bit 1 and bit 6 would be compared against the CANIDAR0/1/2/3 registers. These would be configured as: 00010100100 In this case bits 1 and 6 are set to `0', but since they are ignored it is equally valid to set them to `1'. 12.5.3.1 Identifier Acceptance Filters example As described above, filters work by comparisons to individual bits in the CAN message identifier field. The filter will check each one of the eleven bits of a standard CAN message identifier. Suppose a filter value of 0001x1001x0. In this simple example, there are only three possible CAN messages. Filter value: 0001x1001x0 Message 1: 00011100110 Message 2: 00110100110 Message 3: 00010100100 Message 2 will be rejected since its third most significant bit is not `0' - 001. The filter is simply a convenient way of defining the set of messages that the CPU must receive. For full 29-bits of an extended CAN message identifier, the filter identifies two sets of messages: one set that it receives and one set that it rejects. Alternatively, the filter may be split into two. This allows the MSCAN to examine only the first 16 bits of a message identifier, but allows two separate filters to perform the checking. See the example below: Filter value A: 0001x1001x0 Filter value B: 00x101x01x0 Message 1: 00011100110 Message 2: 00110100110 Message 3: 00010100100 MSCAN will accept all three messages. Filter A will accept messages 1 and 3 as before and filter B will accept message 2. In practice, it is unimportant which filter accepts the message - messages accepted by either will be placed in the input buffer. A message may be accepted by more than one filter. MC9S08DZ60 Series Data Sheet, Rev. 4 258 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) 12.5.3.2 Protocol Violation Protection The MSCAN protects the user from accidentally violating the CAN protocol through programming errors. The protection logic implements the following features: * The receive and transmit error counters cannot be written or otherwise manipulated. * All registers which control the configuration of the MSCAN cannot be modified while the MSCAN is on-line. The MSCAN has to be in Initialization Mode. The corresponding INITRQ/INITAK handshake bits in the CANCTL0/CANCTL1 registers (see Section 12.3.1, "MSCAN Control Register 0 (CANCTL0)") serve as a lock to protect the following registers: -- MSCAN control 1 register (CANCTL1) -- MSCAN bus timing registers 0 and 1 (CANBTR0, CANBTR1) -- MSCAN identifier acceptance control register (CANIDAC) -- MSCAN identifier acceptance registers (CANIDAR0-CANIDAR7) -- MSCAN identifier mask registers (CANIDMR0-CANIDMR7) * The TXCAN pin is immediately forced to a recessive state when the MSCAN goes into the power down mode or initialization mode (see Section 12.5.5.6, "MSCAN Power Down Mode," and Section 12.5.5.5, "MSCAN Initialization Mode"). * The MSCAN enable bit (CANE) is writable only once in normal system operation modes, which provides further protection against inadvertently disabling the MSCAN. 12.5.3.3 Clock System Figure 12-42 shows the structure of the MSCAN clock generation circuitry. MSCAN Bus Clock CANCLK CLKSRC Prescaler (1 .. 64) Time quanta clock (Tq) CLKSRC Oscillator Clock Figure 12-42. MSCAN Clocking Scheme The clock source bit (CLKSRC) in the CANCTL1 register (12.3.2/-226) defines whether the internal CANCLK is connected to the output of a crystal oscillator (oscillator clock) or to the bus clock. The clock source has to be chosen such that the tight oscillator tolerance requirements (up to 0.4%) of the CAN protocol are met. Additionally, for high CAN bus rates (1 Mbps), a 45% to 55% duty cycle of the clock is required. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 259 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) If the bus clock is generated from a PLL, it is recommended to select the oscillator clock rather than the bus clock due to jitter considerations, especially at the faster CAN bus rates. PLL lock may also be too wide to ensure adequate clock tolerance. For microcontrollers without a clock and reset generator (CRG), CANCLK is driven from the crystal oscillator (oscillator clock). A programmable prescaler generates the time quanta (Tq) clock from CANCLK. A time quantum is the atomic unit of time handled by the MSCAN. Eqn. 12-2 f CANCLK = ----------------------------------------------------Tq ( Prescaler value -) A bit time is subdivided into three segments as described in the Bosch CAN specification. (see Figure 12-43): * SYNC_SEG: This segment has a fixed length of one time quantum. Signal edges are expected to happen within this section. * Time Segment 1: This segment includes the PROP_SEG and the PHASE_SEG1 of the CAN standard. It can be programmed by setting the parameter TSEG1 to consist of 4 to 16 time quanta. * Time Segment 2: This segment represents the PHASE_SEG2 of the CAN standard. It can be programmed by setting the TSEG2 parameter to be 2 to 8 time quanta long. Eqn. 12-3 f Tq Bit Rate = --------------------------------------------------------------------------------( number of Time Quanta ) NRZ Signal SYNC_SEG Time Segment 1 (PROP_SEG + PHASE_SEG1) Time Segment 2 (PHASE_SEG2) 1 4 ... 16 2 ... 8 8 ... 25 Time Quanta = 1 Bit Time Transmit Point Sample Point (single or triple sampling) Figure 12-43. Segments within the Bit Time MC9S08DZ60 Series Data Sheet, Rev. 4 260 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) Table 12-34. Time Segment Syntax Syntax Description System expects transitions to occur on the CAN bus during this period. SYNC_SEG Transmit Point A node in transmit mode transfers a new value to the CAN bus at this point. Sample Point A node in receive mode samples the CAN bus at this point. If the three samples per bit option is selected, then this point marks the position of the third sample. The synchronization jump width (see the Bosch CAN specification for details) can be programmed in a range of 1 to 4 time quanta by setting the SJW parameter. The SYNC_SEG, TSEG1, TSEG2, and SJW parameters are set by programming the MSCAN bus timing registers (CANBTR0, CANBTR1) (see Section 12.3.3, "MSCAN Bus Timing Register 0 (CANBTR0)" and Section 12.3.4, "MSCAN Bus Timing Register 1 (CANBTR1)"). Table 12-35 gives an overview of the CAN compliant segment settings and the related parameter values. NOTE It is the user's responsibility to ensure the bit time settings are in compliance with the CAN standard. Table 12-35. CAN Standard Compliant Bit Time Segment Settings Synchronization Jump Width Time Segment 1 TSEG1 Time Segment 2 TSEG2 5 .. 10 4 .. 9 2 1 1 .. 2 0 .. 1 4 .. 11 3 .. 10 3 2 1 .. 3 0 .. 2 5 .. 12 4 .. 11 4 3 1 .. 4 0 .. 3 6 .. 13 5 .. 12 5 4 1 .. 4 0 .. 3 7 .. 14 6 .. 13 6 5 1 .. 4 0 .. 3 8 .. 15 7 .. 14 7 6 1 .. 4 0 .. 3 9 .. 16 8 .. 15 8 7 1 .. 4 0 .. 3 12.5.4 12.5.4.1 SJW Modes of Operation Normal Modes The MSCAN module behaves as described within this specification in all normal system operation modes. 12.5.4.2 Special Modes The MSCAN module behaves as described within this specification in all special system operation modes. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 261 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) 12.5.4.3 Emulation Modes In all emulation modes, the MSCAN module behaves just like normal system operation modes as described within this specification. 12.5.4.4 Listen-Only Mode In an optional CAN bus monitoring mode (listen-only), the CAN node is able to receive valid data frames and valid remote frames, but it sends only "recessive" bits on the CAN bus. In addition, it cannot start a transmision. If the MAC sub-layer is required to send a "dominant" bit (ACK bit, overload flag, or active error flag), the bit is rerouted internally so that the MAC sub-layer monitors this "dominant" bit, although the CAN bus may remain in recessive state externally. 12.5.4.5 Security Modes The MSCAN module has no security features. 12.5.4.6 Loopback Self Test Mode Loopback self test mode is sometimes used to check software, independent of connections in the external system, to help isolate system problems. In this mode, the transmitter output is internally connected to the receiver input. The RXCAN input pin is ignored and the TXCAN output goes to the recessive state (logic 1). The MSCAN behaves as it does normally when transmitting and treats its own transmitted message as a message received from a remote node. In this state, the MSCAN ignores the bit sent during the ACK slot in the CAN frame acknowledge field to ensure proper reception of its own message. Both transmit and receive interrupts are generated. 12.5.5 Low-Power Options If the MSCAN is disabled (CANE = 0), the MSCAN clocks are stopped for power saving. If the MSCAN is enabled (CANE = 1), the MSCAN has two additional modes with reduced power consumption, compared to normal mode: sleep and power down mode. In sleep mode, power consumption is reduced by stopping all clocks except those to access the registers from the CPU side. In power down mode, all clocks are stopped and no power is consumed. Table 12-36 summarizes the combinations of MSCAN and CPU modes. A particular combination of modes is entered by the given settings on the CSWAI and SLPRQ/SLPAK bits. For all modes, an MSCAN wake-up interrupt can occur only if the MSCAN is in sleep mode (SLPRQ = 1 and SLPAK = 1), wake-up functionality is enabled (WUPE = 1), and the wake-up interrupt is enabled (WUPIE = 1). MC9S08DZ60 Series Data Sheet, Rev. 4 262 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) Table 12-36. CPU vs. MSCAN Operating Modes MSCAN Mode Reduced Power Consumption CPU Mode Normal Sleep Run CSWAI = X SLPRQ = 1 SLPAK = 1 Wait CSWAI = 0 SLPRQ = 0 SLPAK = 0 CSWAI = 0 SLPRQ = 1 SLPAK = 1 CSWAI = 1 SLPRQ = X SLPAK = X CSWAI = X SLPRQ = X SLPAK = X CSWAI = X2 SLPRQ = 1 SLPAK = 1 CSWAI = X SLPRQ = 0 SLPAK = 0 CSWAI = X SLPRQ = X SLPAK = X CSWAI = X SLPRQ = X SLPAK = X CSWAI = X SLPRQ = X SLPAK = X Stop1 or 2 2 Disabled (CANE=0) CSWAI = X1 SLPRQ = 0 SLPAK = 0 Stop3 1 Power Down CSWAI = X SLPRQ = X SLPAK = X `X' means don't care. For a safe wake up from Sleep mode, SLPRQ and SLPAK must be set to 1 before going into Stop3 mode. 12.5.5.1 Operation in Run Mode As shown in Table 12-36, only MSCAN sleep mode is available as low power option when the CPU is in run mode. 12.5.5.2 Operation in Wait Mode The WAIT instruction puts the MCU in a low power consumption stand-by mode. If the CSWAI bit is set, additional power can be saved in power down mode because the CPU clocks are stopped. After leaving this power down mode, the MSCAN restarts its internal controllers and enters normal mode again. While the CPU is in wait mode, the MSCAN can be operated in normal mode and generate interrupts (registers can be accessed via background debug mode). The MSCAN can also operate in any of the low-power modes depending on the values of the SLPRQ/SLPAK and CSWAI bits as seen in Table 12-36. 12.5.5.3 Operation in Stop Mode The STOP instruction puts the MCU in a low power consumption stand-by mode. In stop1 or stop2 modes, the MSCAN is set in power down mode regardless of the value of the SLPRQ/SLPAK. In stop3 mode, power down or sleep modes are determined by the SLPRQ/SLPAK values set prior to entering stop3. CSWAI bit has no function in any of the stop modes.Table 12-36. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 263 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) 12.5.5.4 MSCAN Sleep Mode The CPU can request the MSCAN to enter this low power mode by asserting the SLPRQ bit in the CANCTL0 register. The time when the MSCAN enters sleep mode depends on a fixed synchronization delay and its current activity: * If there are one or more message buffers scheduled for transmission (TXEx = 0), the MSCAN will continue to transmit until all transmit message buffers are empty (TXEx = 1, transmitted successfully or aborted) and then goes into sleep mode. * If the MSCAN is receiving, it continues to receive and goes into sleep mode as soon as the CAN bus next becomes idle. * If the MSCAN is neither transmitting nor receiving, it immediately goes into sleep mode. Bus Clock Domain CAN Clock Domain SLPRQ SYNC sync. SLPRQ sync. SYNC SLPAK CPU Sleep Request SLPAK Flag SLPAK SLPRQ Flag MSCAN in Sleep Mode Figure 12-44. Sleep Request / Acknowledge Cycle NOTE The application software must avoid setting up a transmission (by clearing one or more TXEx flag(s)) and immediately request sleep mode (by setting SLPRQ). Whether the MSCAN starts transmitting or goes into sleep mode directly depends on the exact sequence of operations. If sleep mode is active, the SLPRQ and SLPAK bits are set (Figure 12-44). The application software must use SLPAK as a handshake indication for the request (SLPRQ) to go into sleep mode. When in sleep mode (SLPRQ = 1 and SLPAK = 1), the MSCAN stops its internal clocks. However, clocks that allow register accesses from the CPU side continue to run. If the MSCAN is in bus-off state, it stops counting the 128 occurrences of 11 consecutive recessive bits due to the stopped clocks. The TXCAN pin remains in a recessive state. If RXF = 1, the message can be read and RXF can be cleared. Shifting a new message into the foreground buffer of the receiver FIFO (RxFG) does not take place while in sleep mode. It is possible to access the transmit buffers and to clear the associated TXE flags. No message abort takes place while in sleep mode. MC9S08DZ60 Series Data Sheet, Rev. 4 264 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) If the WUPE bit in CANCLT0 is not asserted, the MSCAN will mask any activity it detects on CAN. The RXCAN pin is therefore held internally in a recessive state. This locks the MSCAN in sleep mode (Figure 12-45). WUPE must be set before entering sleep mode to take effect. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 265 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) The MSCAN is able to leave sleep mode (wake up) only when: * CAN bus activity occurs and WUPE = 1 or * the CPU clears the SLPRQ bit NOTE The CPU cannot clear the SLPRQ bit before sleep mode (SLPRQ = 1 and SLPAK = 1) is active. After wake-up, the MSCAN waits for 11 consecutive recessive bits to synchronize to the CAN bus. As a consequence, if the MSCAN is woken-up by a CAN frame, this frame is not received. The receive message buffers (RxFG and RxBG) contain messages if they were received before sleep mode was entered. All pending actions will be executed upon wake-up; copying of RxBG into RxFG, message aborts and message transmissions. If the MSCAN remains in bus-off state after sleep mode was exited, it continues counting the 128 occurrences of 11 consecutive recessive bits. CAN Activity (CAN Activity & WUPE) | SLPRQ Wait for Idle StartUp CAN Activity SLPRQ CAN Activity & SLPRQ Sleep Idle (CAN Activity & WUPE) | CAN Activity CAN Activity & SLPRQ CAN Activity Tx/Rx Message Active CAN Activity Figure 12-45. Simplified State Transitions for Entering/Leaving Sleep Mode MC9S08DZ60 Series Data Sheet, Rev. 4 266 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) 12.5.5.5 MSCAN Initialization Mode In initialization mode, any on-going transmission or reception is immediately aborted and synchronization to the CAN bus is lost, potentially causing CAN protocol violations. To protect the CAN bus system from fatal consequences of violations, the MSCAN immediately drives the TXCAN pin into a recessive state. NOTE The user is responsible for ensuring that the MSCAN is not active when initialization mode is entered. The recommended procedure is to bring the MSCAN into sleep mode (SLPRQ = 1 and SLPAK = 1) before setting the INITRQ bit in the CANCTL0 register. Otherwise, the abort of an on-going message can cause an error condition and can impact other CAN bus devices. In initialization mode, the MSCAN is stopped. However, interface registers remain accessible. This mode is used to reset the CANCTL0, CANRFLG, CANRIER, CANTFLG, CANTIER, CANTARQ, CANTAAK, and CANTBSEL registers to their default values. In addition, the MSCAN enables the configuration of the CANBTR0, CANBTR1 bit timing registers; CANIDAC; and the CANIDAR, CANIDMR message filters. See Section 12.3.1, "MSCAN Control Register 0 (CANCTL0)," for a detailed description of the initialization mode. Bus Clock Domain CAN Clock Domain INITRQ SYNC sync. INITRQ sync. SYNC INITAK CPU Init Request INITAK Flag INITAK INIT Flag Figure 12-46. Initialization Request/Acknowledge Cycle Due to independent clock domains within the MSCAN, INITRQ must be synchronized to all domains by using a special handshake mechanism. This handshake causes additional synchronization delay (see Section Figure 12-46., "Initialization Request/Acknowledge Cycle"). If there is no message transfer ongoing on the CAN bus, the minimum delay will be two additional bus clocks and three additional CAN clocks. When all parts of the MSCAN are in initialization mode, the INITAK flag is set. The application software must use INITAK as a handshake indication for the request (INITRQ) to go into initialization mode. NOTE The CPU cannot clear INITRQ before initialization mode (INITRQ = 1 and INITAK = 1) is active. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 267 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) 12.5.5.6 MSCAN Power Down Mode The MSCAN is in power down mode (Table 12-36) when * CPU is in stop mode or * CPU is in wait mode and the CSWAI bit is set When entering the power down mode, the MSCAN immediately stops all ongoing transmissions and receptions, potentially causing CAN protocol violations. To protect the CAN bus system from fatal consequences of violations to the above rule, the MSCAN immediately drives the TXCAN pin into a recessive state. NOTE The user is responsible for ensuring that the MSCAN is not active when power down mode is entered. The recommended procedure is to bring the MSCAN into Sleep mode before the STOP or WAIT instruction (if CSWAI is set) is executed. Otherwise, the abort of an ongoing message can cause an error condition and impact other CAN bus devices. In power down mode, all clocks are stopped and no registers can be accessed. If the MSCAN was not in sleep mode before power down mode became active, the module performs an internal recovery cycle after powering up. This causes some fixed delay before the module enters normal mode again. 12.5.5.7 Programmable Wake-Up Function The MSCAN can be programmed to wake up the MSCAN as soon as CAN bus activity is detected (see control bit WUPE in Section 12.3.1, "MSCAN Control Register 0 (CANCTL0)"). The sensitivity to existing CAN bus action can be modified by applying a low-pass filter function to the RXCAN input line while in sleep mode (see control bit WUPM in Section 12.3.2, "MSCAN Control Register 1 (CANCTL1)"). This feature can be used to protect the MSCAN from wake-up due to short glitches on the CAN bus lines. Such glitches can result from--for example--electromagnetic interference within noisy environments. 12.5.6 Reset Initialization The reset state of each individual bit is listed in Section 12.3, "Register Definition," which details all the registers and their bit-fields. 12.5.7 Interrupts This section describes all interrupts originated by the MSCAN. It documents the enable bits and generated flags. Each interrupt is listed and described separately. MC9S08DZ60 Series Data Sheet, Rev. 4 268 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) 12.5.7.1 Description of Interrupt Operation The MSCAN supports four interrupt vectors (see Table 12-37), any of which can be individually masked (for details see sections from Section 12.3.5, "MSCAN Receiver Interrupt Enable Register (CANRIER)," to Section 12.3.7, "MSCAN Transmitter Interrupt Enable Register (CANTIER)"). NOTE The dedicated interrupt vector addresses are defined in the Resets and Interrupts chapter. Table 12-37. Interrupt Vectors Interrupt Source Wake-Up Interrupt (WUPIF) 12.5.7.2 CCR Mask I bit Local Enable CANRIER (WUPIE) Error Interrupts Interrupt (CSCIF, OVRIF) I bit CANRIER (CSCIE, OVRIE) Receive Interrupt (RXF) I bit CANRIER (RXFIE) Transmit Interrupts (TXE[2:0]) I bit CANTIER (TXEIE[2:0]) Transmit Interrupt At least one of the three transmit buffers is empty (not scheduled) and can be loaded to schedule a message for transmission. The TXEx flag of the empty message buffer is set. 12.5.7.3 Receive Interrupt A message is successfully received and shifted into the foreground buffer (RxFG) of the receiver FIFO. This interrupt is generated immediately after receiving the EOF symbol. The RXF flag is set. If there are multiple messages in the receiver FIFO, the RXF flag is set as soon as the next message is shifted to the foreground buffer. 12.5.7.4 Wake-Up Interrupt A wake-up interrupt is generated if activity on the CAN bus occurs during MSCAN internal sleep mode. WUPE (see Section 12.3.1, "MSCAN Control Register 0 (CANCTL0)") must be enabled. 12.5.7.5 Error Interrupt An error interrupt is generated if an overrun of the receiver FIFO, error, warning, or bus-off condition occurrs. Section 12.3.4.1, "MSCAN Receiver Flag Register (CANRFLG) indicates one of the following conditions: * Overrun -- An overrun condition of the receiver FIFO as described in Section 12.5.2.3, "Receive Structures," occurred. * CAN Status Change -- The actual value of the transmit and receive error counters control the CAN bus state of the MSCAN. As soon as the error counters skip into a critical range (Tx/Rx-warning, Tx/Rx-error, bus-off) the MSCAN flags an error condition. The status change, which caused the error condition, is indicated by the TSTAT and RSTAT flags (see MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 269 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) Section 12.3.4.1, "MSCAN Receiver Flag Register (CANRFLG)" and Section 12.3.5, "MSCAN Receiver Interrupt Enable Register (CANRIER)"). 12.5.7.6 Interrupt Acknowledge Interrupts are directly associated with one or more status flags in either the Section 12.3.4.1, "MSCAN Receiver Flag Register (CANRFLG)" or the Section 12.3.6, "MSCAN Transmitter Flag Register (CANTFLG)." Interrupts are pending as long as one of the corresponding flags is set. The flags in CANRFLG and CANTFLG must be reset within the interrupt handler to handshake the interrupt. The flags are reset by writing a 1 to the corresponding bit position. A flag cannot be cleared if the respective condition prevails. NOTE It must be guaranteed that the CPU clears only the bit causing the current interrupt. For this reason, bit manipulation instructions (BSET) must not be used to clear interrupt flags. These instructions may cause accidental clearing of interrupt flags which are set after entering the current interrupt service routine. 12.5.7.7 Recovery from Stop or Wait The MSCAN can recover from stop or wait via the wake-up interrupt. This interrupt can only occur if the MSCAN was in sleep mode (SLPRQ = 1 and SLPAK = 1) before entering power down mode, the wake-up option is enabled (WUPE = 1), and the wake-up interrupt is enabled (WUPIE = 1). 12.6 12.6.1 Initialization/Application Information MSCAN initialization The procedure to initially start up the MSCAN module out of reset is as follows: 1. Assert CANE 2. Write to the configuration registers in initialization mode 3. Clear INITRQ to leave initialization mode and enter normal mode If the configuration of registers which are writable in initialization mode needs to be changed only when the MSCAN module is in normal mode: 1. Bring the module into sleep mode by setting SLPRQ and awaiting SLPAK to assert after the CAN bus becomes idle. 2. Enter initialization mode: assert INITRQ and await INITAK 3. Write to the configuration registers in initialization mode 4. Clear INITRQ to leave initialization mode and continue in normal mode MC9S08DZ60 Series Data Sheet, Rev. 4 270 Freescale Semiconductor Chapter 12 Freescale's Controller Area Network (S08MSCANV1) 12.6.2 Bus-Off Recovery The bus-off recovery is user configurable. The bus-off state can either be exited automatically or on user request. For reasons of backwards compatibility, the MSCAN defaults to automatic recovery after reset. In this case, the MSCAN will become error active again after counting 128 occurrences of 11 consecutive recessive bits on the CAN bus (See the Bosch CAN specification for details). If the MSCAN is configured for user request (BORM set in Section 12.3.2, "MSCAN Control Register 1 (CANCTL1)"), the recovery from bus-off starts after both independent events have become true: * 128 occurrences of 11 consecutive recessive bits on the CAN bus have been monitored * BOHOLD in Section 12.3.12, "MSCAN Miscellaneous Register (CANMISC) has been cleared by the user These two events may occur in any order. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 271 Chapter 12 Freescale's Controller Area Network (S08MSCANV1) MC9S08DZ60 Series Data Sheet, Rev. 4 272 Freescale Semiconductor Chapter 13 Serial Peripheral Interface (S08SPIV3) 13.1 Introduction The serial peripheral interface (SPI) module provides for full-duplex, synchronous, serial communication between the MCU and peripheral devices. These peripheral devices can include other microcontrollers, analog-to-digital converters, shift registers, sensors, memories, etc. The SPI runs at a baud rate up to the bus clock divided by two in master mode and bus clock divided by four in slave mode. All devices in the MC9S08DZ60 Series MCUs contain one SPI module, as shown in the following block diagram. NOTE Ensure that the SPI should not be disabled (SPE=0) at the same time as a bit change to the CPHA bit. These changes should be performed as separate operations or unexpected behavior may occur. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 273 PORT A PTA7/PIA7/ADP7/IRQ PTA6/PIA6/ADP6 PTA5/PIA5/ADP5 PTA4/PIA4/ADP4 PTA3/PIA3/ADP3/ACMP1O PTA2/PIA2/ADP2/ACMP1PTA1/PIA1/ADP1/ACMP1+ PTA0/PIA0/ADP0/MCLK PORT B PTB7/PIB7/ADP15 PTB6/PIB6/ADP14 PTB5/PIB5/ADP13 PTB4/PIB4/ADP12 PTB3/PIB3/ADP11 PTB2/PIB2/ADP10 PTB1/PIB1/ADP9 PTB0/PIB0/ADP8 PORT C PTC7/ADP23 PTC6/ADP22 PTC5/ADP21 PTC4/ADP20 PTC3/ADP19 PTC2/ADP18 PTC1/ADP17 PTC0/ADP16 PORT D PTD7/PID7/TPM1CH5 PTD6/PID6/TPM1CH4 PTD5/PID5/TPM1CH3 PTD4/PID4/TPM1CH2 PTD3/PID3/TPM1CH1 PTD2/PID2/TPM1CH0 PTD1/PID1/TPM2CH1 PTD0/PID0/TPM2CH0 PORT E PTE7/RxD2/RXCAN PTE6/TxD2/TXCAN PTE5/SDA/MISO PTE4/SCL/MOSI PTE3/SPSCK PTE2/SS PTE1/RxD1 PTE0/TxD1 PORT F PTF7 PTF6/ACMP2O PTF5/ACMP2PTF4/ACMP2+ PTF3/TPM2CLK/SDA PTF2/TPM1CLK/SCL PTF1/RxD2 PTF0/TxD2 PORT G Chapter 13 Serial Peripheral Interface (S08SPIV3) PTG5 PTG4 PTG3 PTG2 PTG1/XTAL PTG0/EXTAL HCS08 CORE CPU BKGD/MS BDC ANALOG COMPARATOR (ACMP1) BKP ACMP1O ACMP1ACMP1+ HCS08 SYSTEM CONTROL RESETS AND INTERRUPTS MODES OF OPERATION POWER MANAGEMENT COP LVD INT IRQ ADP7-ADP0 24-CHANNEL,12-BIT ANALOG-TO-DIGITAL CONVERTER (ADC) VREFH VREFL VDDA VSSA USER FLASH MC9S0DZ60 = 60K MC9S0DZ48 = 48K MC9S0DZ32 = 32K MC9S0DZ16 = 16K USER EEPROM MC9S0DZ60 = 2K TPM1CH5 TPM1CH0 6 TPM1CLK 2-CHANNEL TIMER/PWM MODULE (TPM2) TPM2CH1, TPM2CH0 TPM2CLK CONTROLLER AREA NETWORK (MSCAN) SERIAL PERIPHERAL INTERFACE MODULE (SPI) DEBUG MODULE (DBG) SERIAL COMMUNICATIONS INTERFACE (SCI1) VOLTAGE REGULATOR ADP15-ADP8 ADP23-ADP16 6-CHANNEL TIMER/PWM MODULE (TPM1) USER RAM MC9S0DZ60 = 4K REAL-TIME COUNTER (RTC) VDD VDD VSS VSS 8 IRQ RESET ANALOG COMPARATOR (ACMP2) IIC MODULE (IIC) SERIAL COMMUNICATIONS INTERFACE (SCI2) RxCAN TxCAN MISO MOSI SPSCK SS RxD1 TxD1 ACMP2O ACMP2ACMP2+ SDA SCL RxD2 TxD2 MULTI-PURPOSE CLOCK GENERATOR (MCG) XTAL EXTAL OSCILLATOR (XOSC) - VREFH/VREFL internally connected to VDDA/VSSA in 48-pin and 32-pin packages - VDD and VSS pins are each internally connected to two pads in 32-pin package - Pin not connected in 48-pin and 32-pin packages - Pin not connected in 32-pin package Figure 13-1. MC9S08DZ60 Block Diagram MC9S08DZ60 Series Data Sheet, Rev. 4 274 Freescale Semiconductor Chapter 13 Serial Peripheral Interface (S08SPIV3) 13.1.1 Features Features of the SPI module include: * Master or slave mode operation * Full-duplex or single-wire bidirectional option * Programmable transmit bit rate * Double-buffered transmit and receive * Serial clock phase and polarity options * Slave select output * Selectable MSB-first or LSB-first shifting 13.1.2 Block Diagrams This section includes block diagrams showing SPI system connections, the internal organization of the SPI module, and the SPI clock dividers that control the master mode bit rate. 13.1.2.1 SPI System Block Diagram Figure 13-2 shows the SPI modules of two MCUs connected in a master-slave arrangement. The master device initiates all SPI data transfers. During a transfer, the master shifts data out (on the MOSI pin) to the slave while simultaneously shifting data in (on the MISO pin) from the slave. The transfer effectively exchanges the data that was in the SPI shift registers of the two SPI systems. The SPSCK signal is a clock output from the master and an input to the slave. The slave device must be selected by a low level on the slave select input (SS pin). In this system, the master device has configured its SS pin as an optional slave select output. SLAVE MASTER MOSI MOSI SPI SHIFTER 7 6 5 4 3 2 SPI SHIFTER 1 0 MISO SPSCK CLOCK GENERATOR SS MISO 7 6 5 4 3 2 1 0 SPSCK SS Figure 13-2. SPI System Connections MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 275 Chapter 13 Serial Peripheral Interface (S08SPIV3) The most common uses of the SPI system include connecting simple shift registers for adding input or output ports or connecting small peripheral devices such as serial A/D or D/A converters. Although Figure 13-2 shows a system where data is exchanged between two MCUs, many practical systems involve simpler connections where data is unidirectionally transferred from the master MCU to a slave or from a slave to the master MCU. 13.1.2.2 SPI Module Block Diagram Figure 13-3 is a block diagram of the SPI module. The central element of the SPI is the SPI shift register. Data is written to the double-buffered transmitter (write to SPID) and gets transferred to the SPI shift register at the start of a data transfer. After shifting in a byte of data, the data is transferred into the double-buffered receiver where it can be read (read from SPID). Pin multiplexing logic controls connections between MCU pins and the SPI module. When the SPI is configured as a master, the clock output is routed to the SPSCK pin, the shifter output is routed to MOSI, and the shifter input is routed from the MISO pin. When the SPI is configured as a slave, the SPSCK pin is routed to the clock input of the SPI, the shifter output is routed to MISO, and the shifter input is routed from the MOSI pin. In the external SPI system, simply connect all SPSCK pins to each other, all MISO pins together, and all MOSI pins together. Peripheral devices often use slightly different names for these pins. MC9S08DZ60 Series Data Sheet, Rev. 4 276 Freescale Semiconductor Chapter 13 Serial Peripheral Interface (S08SPIV3) PIN CONTROL M SPE MOSI (MOMI) S Tx BUFFER (WRITE SPID) ENABLE SPI SYSTEM M SHIFT OUT SPI SHIFT REGISTER SHIFT IN MISO (SISO) S SPC0 Rx BUFFER (READ SPID) BIDIROE SHIFT DIRECTION LSBFE SHIFT CLOCK Rx BUFFER FULL Tx BUFFER EMPTY MASTER CLOCK BUS RATE CLOCK SPIBR CLOCK GENERATOR MSTR CLOCK LOGIC SLAVE CLOCK MASTER/SLAVE M SPSCK S MASTER/ SLAVE MODE SELECT MODFEN SSOE MODE FAULT DETECTION SS SPRF SPTEF SPTIE MODF SPIE SPI INTERRUPT REQUEST Figure 13-3. SPI Module Block Diagram 13.1.3 SPI Baud Rate Generation As shown in Figure 13-4, the clock source for the SPI baud rate generator is the bus clock. The three prescale bits (SPPR2:SPPR1:SPPR0) choose a prescale divisor of 1, 2, 3, 4, 5, 6, 7, or 8. The three rate select bits (SPR2:SPR1:SPR0) divide the output of the prescaler stage by 2, 4, 8, 16, 32, 64, 128, or 256 to get the internal SPI master mode bit-rate clock. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 277 Chapter 13 Serial Peripheral Interface (S08SPIV3) BUS CLOCK PRESCALER CLOCK RATE DIVIDER DIVIDE BY 1, 2, 3, 4, 5, 6, 7, or 8 DIVIDE BY 2, 4, 8, 16, 32, 64, 128, or 256 SPPR2:SPPR1:SPPR0 SPR2:SPR1:SPR0 MASTER SPI BIT RATE Figure 13-4. SPI Baud Rate Generation 13.2 External Signal Description The SPI optionally shares four port pins. The function of these pins depends on the settings of SPI control bits. When the SPI is disabled (SPE = 0), these four pins revert to being general-purpose port I/O pins that are not controlled by the SPI. 13.2.1 SPSCK -- SPI Serial Clock When the SPI is enabled as a slave, this pin is the serial clock input. When the SPI is enabled as a master, this pin is the serial clock output. 13.2.2 MOSI -- Master Data Out, Slave Data In When the SPI is enabled as a master and SPI pin control zero (SPC0) is 0 (not bidirectional mode), this pin is the serial data output. When the SPI is enabled as a slave and SPC0 = 0, this pin is the serial data input. If SPC0 = 1 to select single-wire bidirectional mode, and master mode is selected, this pin becomes the bidirectional data I/O pin (MOMI). Also, the bidirectional mode output enable bit determines whether the pin acts as an input (BIDIROE = 0) or an output (BIDIROE = 1). If SPC0 = 1 and slave mode is selected, this pin is not used by the SPI and reverts to being a general-purpose port I/O pin. 13.2.3 MISO -- Master Data In, Slave Data Out When the SPI is enabled as a master and SPI pin control zero (SPC0) is 0 (not bidirectional mode), this pin is the serial data input. When the SPI is enabled as a slave and SPC0 = 0, this pin is the serial data output. If SPC0 = 1 to select single-wire bidirectional mode, and slave mode is selected, this pin becomes the bidirectional data I/O pin (SISO) and the bidirectional mode output enable bit determines whether the pin acts as an input (BIDIROE = 0) or an output (BIDIROE = 1). If SPC0 = 1 and master mode is selected, this pin is not used by the SPI and reverts to being a general-purpose port I/O pin. 13.2.4 SS -- Slave Select When the SPI is enabled as a slave, this pin is the low-true slave select input. When the SPI is enabled as a master and mode fault enable is off (MODFEN = 0), this pin is not used by the SPI and reverts to being a general-purpose port I/O pin. When the SPI is enabled as a master and MODFEN = 1, the slave select output enable bit determines whether this pin acts as the mode fault input (SSOE = 0) or as the slave select output (SSOE = 1). MC9S08DZ60 Series Data Sheet, Rev. 4 278 Freescale Semiconductor Chapter 13 Serial Peripheral Interface (S08SPIV3) 13.3 Modes of Operation 13.3.1 SPI in Stop Modes The SPI is disabled in all stop modes, regardless of the settings before executing the STOP instruction. During either stop1 or stop2 mode, the SPI module will be fully powered down. Upon wake-up from stop1 or stop2 mode, the SPI module will be in the reset state. During stop3 mode, clocks to the SPI module are halted. No registers are affected. If stop3 is exited with a reset, the SPI will be put into its reset state. If stop3 is exited with an interrupt, the SPI continues from the state it was in when stop3 was entered. 13.4 Register Definition The SPI has five 8-bit registers to select SPI options, control baud rate, report SPI status, and for transmit/receive data. Refer to the direct-page register summary in the Memory chapter of this data sheet for the absolute address assignments for all SPI registers. This section refers to registers and control bits only by their names, and a Freescale-provided equate or header file is used to translate these names into the appropriate absolute addresses. 13.4.1 SPI Control Register 1 (SPIC1) This read/write register includes the SPI enable control, interrupt enables, and configuration options. 7 6 5 4 3 2 1 0 SPIE SPE SPTIE MSTR CPOL CPHA SSOE LSBFE 0 0 0 0 0 1 0 0 R W Reset Figure 13-5. SPI Control Register 1 (SPIC1) Table 13-1. SPIC1 Field Descriptions Field Description 7 SPIE SPI Interrupt Enable (for SPRF and MODF) -- This is the interrupt enable for SPI receive buffer full (SPRF) and mode fault (MODF) events. 0 Interrupts from SPRF and MODF inhibited (use polling) 1 When SPRF or MODF is 1, request a hardware interrupt 6 SPE SPI System Enable -- Disabling the SPI halts any transfer that is in progress, clears data buffers, and initializes internal state machines. SPRF is cleared and SPTEF is set to indicate the SPI transmit data buffer is empty. 0 SPI system inactive 1 SPI system enabled 5 SPTIE SPI Transmit Interrupt Enable -- This is the interrupt enable bit for SPI transmit buffer empty (SPTEF). 0 Interrupts from SPTEF inhibited (use polling) 1 When SPTEF is 1, hardware interrupt requested MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 279 Chapter 13 Serial Peripheral Interface (S08SPIV3) Table 13-1. SPIC1 Field Descriptions (continued) Field Description 4 MSTR Master/Slave Mode Select 0 SPI module configured as a slave SPI device 1 SPI module configured as a master SPI device 3 CPOL Clock Polarity -- This bit effectively places an inverter in series with the clock signal from a master SPI or to a slave SPI device. Refer to Section 13.5.1, "SPI Clock Formats" for more details. 0 Active-high SPI clock (idles low) 1 Active-low SPI clock (idles high) 2 CPHA Clock Phase -- This bit selects one of two clock formats for different kinds of synchronous serial peripheral devices. Refer to Section 13.5.1, "SPI Clock Formats" for more details. 0 First edge on SPSCK occurs at the middle of the first cycle of an 8-cycle data transfer 1 First edge on SPSCK occurs at the start of the first cycle of an 8-cycle data transfer 1 SSOE Slave Select Output Enable -- This bit is used in combination with the mode fault enable (MODFEN) bit in SPCR2 and the master/slave (MSTR) control bit to determine the function of the SS pin as shown in Table 13-2. 0 LSBFE LSB First (Shifter Direction) 0 SPI serial data transfers start with most significant bit 1 SPI serial data transfers start with least significant bit Table 13-2. SS Pin Function MODFEN SSOE Master Mode Slave Mode 0 0 General-purpose I/O (not SPI) Slave select input 0 1 General-purpose I/O (not SPI) Slave select input 1 0 SS input for mode fault Slave select input 1 1 Automatic SS output Slave select input NOTE Ensure that the SPI should not be disabled (SPE=0) at the same time as a bit change to the CPHA bit. These changes should be performed as separate operations or unexpected behavior may occur. 13.4.2 SPI Control Register 2 (SPIC2) This read/write register is used to control optional features of the SPI system. Bits 7, 6, 5, and 2 are not implemented and always read 0. R 7 6 5 0 0 0 4 3 MODFEN BIDIROE 0 0 2 1 0 SPISWAI SPC0 0 0 0 W Reset 0 0 0 0 = Unimplemented or Reserved Figure 13-6. SPI Control Register 2 (SPIC2) MC9S08DZ60 Series Data Sheet, Rev. 4 280 Freescale Semiconductor Chapter 13 Serial Peripheral Interface (S08SPIV3) Table 13-3. SPIC2 Register Field Descriptions Field Description 4 MODFEN Master Mode-Fault Function Enable -- When the SPI is configured for slave mode, this bit has no meaning or effect. (The SS pin is the slave select input.) In master mode, this bit determines how the SS pin is used (refer to Table 13-2 for more details). 0 Mode fault function disabled, master SS pin reverts to general-purpose I/O not controlled by SPI 1 Mode fault function enabled, master SS pin acts as the mode fault input or the slave select output 3 BIDIROE Bidirectional Mode Output Enable -- When bidirectional mode is enabled by SPI pin control 0 (SPC0) = 1, BIDIROE determines whether the SPI data output driver is enabled to the single bidirectional SPI I/O pin. Depending on whether the SPI is configured as a master or a slave, it uses either the MOSI (MOMI) or MISO (SISO) pin, respectively, as the single SPI data I/O pin. When SPC0 = 0, BIDIROE has no meaning or effect. 0 Output driver disabled so SPI data I/O pin acts as an input 1 SPI I/O pin enabled as an output 1 SPISWAI SPI Stop in Wait Mode 0 SPI clocks continue to operate in wait mode 1 SPI clocks stop when the MCU enters wait mode 0 SPC0 13.4.3 SPI Pin Control 0 -- The SPC0 bit chooses single-wire bidirectional mode. If MSTR = 0 (slave mode), the SPI uses the MISO (SISO) pin for bidirectional SPI data transfers. If MSTR = 1 (master mode), the SPI uses the MOSI (MOMI) pin for bidirectional SPI data transfers. When SPC0 = 1, BIDIROE is used to enable or disable the output driver for the single bidirectional SPI I/O pin. 0 SPI uses separate pins for data input and data output 1 SPI configured for single-wire bidirectional operation SPI Baud Rate Register (SPIBR) This register is used to set the prescaler and bit rate divisor for an SPI master. This register may be read or written at any time. 7 R 6 5 4 3 SPPR2 SPPR1 SPPR0 0 0 0 0 2 1 0 SPR2 SPR1 SPR0 0 0 0 0 W Reset 0 0 = Unimplemented or Reserved Figure 13-7. SPI Baud Rate Register (SPIBR) Table 13-4. SPIBR Register Field Descriptions Field Description 6:4 SPPR[2:0] SPI Baud Rate Prescale Divisor -- This 3-bit field selects one of eight divisors for the SPI baud rate prescaler as shown in Table 13-5. The input to this prescaler is the bus rate clock (BUSCLK). The output of this prescaler drives the input of the SPI baud rate divider (see Figure 13-4). 2:0 SPR[2:0] SPI Baud Rate Divisor -- This 3-bit field selects one of eight divisors for the SPI baud rate divider as shown in Table 13-6. The input to this divider comes from the SPI baud rate prescaler (see Figure 13-4). The output of this divider is the SPI bit rate clock for master mode. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 281 Chapter 13 Serial Peripheral Interface (S08SPIV3) Table 13-5. SPI Baud Rate Prescaler Divisor SPPR2:SPPR1:SPPR0 Prescaler Divisor 0:0:0 1 0:0:1 2 0:1:0 3 0:1:1 4 1:0:0 5 1:0:1 6 1:1:0 7 1:1:1 8 Table 13-6. SPI Baud Rate Divisor 13.4.4 SPR2:SPR1:SPR0 Rate Divisor 0:0:0 2 0:0:1 4 0:1:0 8 0:1:1 16 1:0:0 32 1:0:1 64 1:1:0 128 1:1:1 256 SPI Status Register (SPIS) This register has three read-only status bits. Bits 6, 3, 2, 1, and 0 are not implemented and always read 0. Writes have no meaning or effect. R 7 6 5 4 3 2 1 0 SPRF 0 SPTEF MODF 0 0 0 0 0 0 1 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 13-8. SPI Status Register (SPIS) MC9S08DZ60 Series Data Sheet, Rev. 4 282 Freescale Semiconductor Chapter 13 Serial Peripheral Interface (S08SPIV3) Table 13-7. SPIS Register Field Descriptions Field Description 7 SPRF SPI Read Buffer Full Flag -- SPRF is set at the completion of an SPI transfer to indicate that received data may be read from the SPI data register (SPID). SPRF is cleared by reading SPRF while it is set, then reading the SPI data register. 0 No data available in the receive data buffer 1 Data available in the receive data buffer 5 SPTEF SPI Transmit Buffer Empty Flag -- This bit is set when there is room in the transmit data buffer. It is cleared by reading SPIS with SPTEF set, followed by writing a data value to the transmit buffer at SPID. SPIS must be read with SPTEF = 1 before writing data to SPID or the SPID write will be ignored. SPTEF generates an SPTEF CPU interrupt request if the SPTIE bit in the SPIC1 is also set. SPTEF is automatically set when a data byte transfers from the transmit buffer into the transmit shift register. For an idle SPI (no data in the transmit buffer or the shift register and no transfer in progress), data written to SPID is transferred to the shifter almost immediately so SPTEF is set within two bus cycles allowing a second 8-bit data value to be queued into the transmit buffer. After completion of the transfer of the value in the shift register, the queued value from the transmit buffer will automatically move to the shifter and SPTEF will be set to indicate there is room for new data in the transmit buffer. If no new data is waiting in the transmit buffer, SPTEF simply remains set and no data moves from the buffer to the shifter. 0 SPI transmit buffer not empty 1 SPI transmit buffer empty 4 MODF Master Mode Fault Flag -- MODF is set if the SPI is configured as a master and the slave select input goes low, indicating some other SPI device is also configured as a master. The SS pin acts as a mode fault error input only when MSTR = 1, MODFEN = 1, and SSOE = 0; otherwise, MODF will never be set. MODF is cleared by reading MODF while it is 1, then writing to SPI control register 1 (SPIC1). 0 No mode fault error 1 Mode fault error detected 13.4.5 SPI Data Register (SPID) 7 6 5 4 3 2 1 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 R W Reset Figure 13-9. SPI Data Register (SPID) Reads of this register return the data read from the receive data buffer. Writes to this register write data to the transmit data buffer. When the SPI is configured as a master, writing data to the transmit data buffer initiates an SPI transfer. Data should not be written to the transmit data buffer unless the SPI transmit buffer empty flag (SPTEF) is set, indicating there is room in the transmit buffer to queue a new transmit byte. Data may be read from SPID any time after SPRF is set and before another transfer is finished. Failure to read the data out of the receive data buffer before a new transfer ends causes a receive overrun condition and the data from the new transfer is lost. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 283 Chapter 13 Serial Peripheral Interface (S08SPIV3) 13.5 Functional Description An SPI transfer is initiated by checking for the SPI transmit buffer empty flag (SPTEF = 1) and then writing a byte of data to the SPI data register (SPID) in the master SPI device. When the SPI shift register is available, this byte of data is moved from the transmit data buffer to the shifter, SPTEF is set to indicate there is room in the buffer to queue another transmit character if desired, and the SPI serial transfer starts. During the SPI transfer, data is sampled (read) on the MISO pin at one SPSCK edge and shifted, changing the bit value on the MOSI pin, one-half SPSCK cycle later. After eight SPSCK cycles, the data that was in the shift register of the master has been shifted out the MOSI pin to the slave while eight bits of data were shifted in the MISO pin into the master's shift register. At the end of this transfer, the received data byte is moved from the shifter into the receive data buffer and SPRF is set to indicate the data can be read by reading SPID. If another byte of data is waiting in the transmit buffer at the end of a transfer, it is moved into the shifter, SPTEF is set, and a new transfer is started. Normally, SPI data is transferred most significant bit (MSB) first. If the least significant bit first enable (LSBFE) bit is set, SPI data is shifted LSB first. When the SPI is configured as a slave, its SS pin must be driven low before a transfer starts and SS must stay low throughout the transfer. If a clock format where CPHA = 0 is selected, SS must be driven to a logic 1 between successive transfers. If CPHA = 1, SS may remain low between successive transfers. See Section 13.5.1, "SPI Clock Formats" for more details. Because the transmitter and receiver are double buffered, a second byte, in addition to the byte currently being shifted out, can be queued into the transmit data buffer, and a previously received character can be in the receive data buffer while a new character is being shifted in. The SPTEF flag indicates when the transmit buffer has room for a new character. The SPRF flag indicates when a received character is available in the receive data buffer. The received character must be read out of the receive buffer (read SPID) before the next transfer is finished or a receive overrun error results. In the case of a receive overrun, the new data is lost because the receive buffer still held the previous character and was not ready to accept the new data. There is no indication for such an overrun condition so the application system designer must ensure that previous data has been read from the receive buffer before a new transfer is initiated. 13.5.1 SPI Clock Formats To accommodate a wide variety of synchronous serial peripherals from different manufacturers, the SPI system has a clock polarity (CPOL) bit and a clock phase (CPHA) control bit to select one of four clock formats for data transfers. CPOL selectively inserts an inverter in series with the clock. CPHA chooses between two different clock phase relationships between the clock and data. Figure 13-10 shows the clock formats when CPHA = 1. At the top of the figure, the eight bit times are shown for reference with bit 1 starting at the first SPSCK edge and bit 8 ending one-half SPSCK cycle after the sixteenth SPSCK edge. The MSB first and LSB first lines show the order of SPI data bits depending on the setting in LSBFE. Both variations of SPSCK polarity are shown, but only one of these waveforms applies for a specific transfer, depending on the value in CPOL. The SAMPLE IN waveform applies to the MOSI input of a slave or the MISO input of a master. The MOSI waveform applies to the MOSI output MC9S08DZ60 Series Data Sheet, Rev. 4 284 Freescale Semiconductor Chapter 13 Serial Peripheral Interface (S08SPIV3) pin from a master and the MISO waveform applies to the MISO output from a slave. The SS OUT waveform applies to the slave select output from a master (provided MODFEN and SSOE = 1). The master SS output goes to active low one-half SPSCK cycle before the start of the transfer and goes back high at the end of the eighth bit time of the transfer. The SS IN waveform applies to the slave select input of a slave. BIT TIME # (REFERENCE) 1 2 ... 6 7 8 BIT 7 BIT 0 BIT 6 BIT 1 ... ... BIT 2 BIT 5 BIT 1 BIT 6 BIT 0 BIT 7 SPSCK (CPOL = 0) SPSCK (CPOL = 1) SAMPLE IN (MISO OR MOSI) MOSI (MASTER OUT) MSB FIRST LSB FIRST MISO (SLAVE OUT) SS OUT (MASTER) SS IN (SLAVE) Figure 13-10. SPI Clock Formats (CPHA = 1) When CPHA = 1, the slave begins to drive its MISO output when SS goes to active low, but the data is not defined until the first SPSCK edge. The first SPSCK edge shifts the first bit of data from the shifter onto the MOSI output of the master and the MISO output of the slave. The next SPSCK edge causes both the master and the slave to sample the data bit values on their MISO and MOSI inputs, respectively. At the third SPSCK edge, the SPI shifter shifts one bit position which shifts in the bit value that was just sampled, and shifts the second data bit value out the other end of the shifter to the MOSI and MISO outputs of the master and slave, respectively. When CHPA = 1, the slave's SS input is not required to go to its inactive high level between transfers. Figure 13-11 shows the clock formats when CPHA = 0. At the top of the figure, the eight bit times are shown for reference with bit 1 starting as the slave is selected (SS IN goes low), and bit 8 ends at the last SPSCK edge. The MSB first and LSB first lines show the order of SPI data bits depending on the setting MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 285 Chapter 13 Serial Peripheral Interface (S08SPIV3) in LSBFE. Both variations of SPSCK polarity are shown, but only one of these waveforms applies for a specific transfer, depending on the value in CPOL. The SAMPLE IN waveform applies to the MOSI input of a slave or the MISO input of a master. The MOSI waveform applies to the MOSI output pin from a master and the MISO waveform applies to the MISO output from a slave. The SS OUT waveform applies to the slave select output from a master (provided MODFEN and SSOE = 1). The master SS output goes to active low at the start of the first bit time of the transfer and goes back high one-half SPSCK cycle after the end of the eighth bit time of the transfer. The SS IN waveform applies to the slave select input of a slave. BIT TIME # (REFERENCE) 1 2 BIT 7 BIT 0 BIT 6 BIT 1 ... 6 7 8 BIT 2 BIT 5 BIT 1 BIT 6 BIT 0 BIT 7 SPSCK (CPOL = 0) SPSCK (CPOL = 1) SAMPLE IN (MISO OR MOSI) MOSI (MASTER OUT) MSB FIRST LSB FIRST ... ... MISO (SLAVE OUT) SS OUT (MASTER) SS IN (SLAVE) Figure 13-11. SPI Clock Formats (CPHA = 0) When CPHA = 0, the slave begins to drive its MISO output with the first data bit value (MSB or LSB depending on LSBFE) when SS goes to active low. The first SPSCK edge causes both the master and the slave to sample the data bit values on their MISO and MOSI inputs, respectively. At the second SPSCK edge, the SPI shifter shifts one bit position which shifts in the bit value that was just sampled and shifts the second data bit value out the other end of the shifter to the MOSI and MISO outputs of the master and slave, respectively. When CPHA = 0, the slave's SS input must go to its inactive high level between transfers. MC9S08DZ60 Series Data Sheet, Rev. 4 286 Freescale Semiconductor Chapter 13 Serial Peripheral Interface (S08SPIV3) 13.5.2 SPI Interrupts There are three flag bits, two interrupt mask bits, and one interrupt vector associated with the SPI system. The SPI interrupt enable mask (SPIE) enables interrupts from the SPI receiver full flag (SPRF) and mode fault flag (MODF). The SPI transmit interrupt enable mask (SPTIE) enables interrupts from the SPI transmit buffer empty flag (SPTEF). When one of the flag bits is set, and the associated interrupt mask bit is set, a hardware interrupt request is sent to the CPU. If the interrupt mask bits are cleared, software can poll the associated flag bits instead of using interrupts. The SPI interrupt service routine (ISR) should check the flag bits to determine what event caused the interrupt. The service routine should also clear the flag bit(s) before returning from the ISR (usually near the beginning of the ISR). 13.5.3 Mode Fault Detection A mode fault occurs and the mode fault flag (MODF) becomes set when a master SPI device detects an error on the SS pin (provided the SS pin is configured as the mode fault input signal). The SS pin is configured to be the mode fault input signal when MSTR = 1, mode fault enable is set (MODFEN = 1), and slave select output enable is clear (SSOE = 0). The mode fault detection feature can be used in a system where more than one SPI device might become a master at the same time. The error is detected when a master's SS pin is low, indicating that some other SPI device is trying to address this master as if it were a slave. This could indicate a harmful output driver conflict, so the mode fault logic is designed to disable all SPI output drivers when such an error is detected. When a mode fault is detected, MODF is set and MSTR is cleared to change the SPI configuration back to slave mode. The output drivers on the SPSCK, MOSI, and MISO (if not bidirectional mode) are disabled. MODF is cleared by reading it while it is set, then writing to the SPI control register 1 (SPIC1). User software should verify the error condition has been corrected before changing the SPI back to master mode. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 287 Chapter 13 Serial Peripheral Interface (S08SPIV3) MC9S08DZ60 Series Data Sheet, Rev. 4 288 Freescale Semiconductor Chapter 14 Serial Communications Interface (S08SCIV4) 14.1 Introduction All MCUs in the MC9S08DZ60 Series include SCI1 and SCI2. * * 14.1.1 NOTE MC9S08DZ60 Series devices operate at a higher voltage range (2.7 V to 5.5 V) and do not include stop1 mode. Please ignore references to stop1. The RxD1 pin does not contain a clamp diode to VDD and should not be driven above VDD. The voltage measured on the internally pulled up RxD1 pin may be as low as VDD - 0.7 V. The internal gates connected to this pin are pulled all the way to VDD. SCI2 Configuration Information The SCI2 module pins, TxD2 and RxD2 can be repositioned under software control using SCI2PS in SOPT1 as shown in Table 14-1. SCI2PS in SOPT1 selects which general-purpose I/O ports are associated with SCI2 operation. Table 14-1. SCI2 Position Options SCI2PS in SOPT1 Port Pin for TxD2 Port Pin for RxD2 0 (default) PTF0 PTF1 1 PTE6 PTE7 MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 289 PORT A PTA7/PIA7/ADP7/IRQ PTA6/PIA6/ADP6 PTA5/PIA5/ADP5 PTA4/PIA4/ADP4 PTA3/PIA3/ADP3/ACMP1O PTA2/PIA2/ADP2/ACMP1PTA1/PIA1/ADP1/ACMP1+ PTA0/PIA0/ADP0/MCLK PORT B PTB7/PIB7/ADP15 PTB6/PIB6/ADP14 PTB5/PIB5/ADP13 PTB4/PIB4/ADP12 PTB3/PIB3/ADP11 PTB2/PIB2/ADP10 PTB1/PIB1/ADP9 PTB0/PIB0/ADP8 PORT C PTC7/ADP23 PTC6/ADP22 PTC5/ADP21 PTC4/ADP20 PTC3/ADP19 PTC2/ADP18 PTC1/ADP17 PTC0/ADP16 PORT D PTD7/PID7/TPM1CH5 PTD6/PID6/TPM1CH4 PTD5/PID5/TPM1CH3 PTD4/PID4/TPM1CH2 PTD3/PID3/TPM1CH1 PTD2/PID2/TPM1CH0 PTD1/PID1/TPM2CH1 PTD0/PID0/TPM2CH0 PORT E PTE7/RxD2/RXCAN PTE6/TxD2/TXCAN PTE5/SDA/MISO PTE4/SCL/MOSI PTE3/SPSCK PTE2/SS PTE1/RxD1 PTE0/TxD1 PORT F PTF7 PTF6/ACMP2O PTF5/ACMP2PTF4/ACMP2+ PTF3/TPM2CLK/SDA PTF2/TPM1CLK/SCL PTF1/RxD2 PTF0/TxD2 PORT G Chapter 14 Serial Communications Interface (S08SCIV4) PTG5 PTG4 PTG3 PTG2 PTG1/XTAL PTG0/EXTAL HCS08 CORE CPU BKGD/MS BDC ANALOG COMPARATOR (ACMP1) BKP ACMP1O ACMP1ACMP1+ HCS08 SYSTEM CONTROL RESETS AND INTERRUPTS MODES OF OPERATION POWER MANAGEMENT COP LVD INT IRQ ADP7-ADP0 24-CHANNEL,12-BIT ANALOG-TO-DIGITAL CONVERTER (ADC) VREFH VREFL VDDA VSSA USER FLASH MC9S0DZ60 = 60K MC9S0DZ48 = 48K MC9S0DZ32 = 32K MC9S0DZ16 = 16K USER EEPROM MC9S0DZ60 = 2K TPM1CH5 TPM1CH0 6 TPM1CLK 2-CHANNEL TIMER/PWM MODULE (TPM2) TPM2CH1, TPM2CH0 TPM2CLK CONTROLLER AREA NETWORK (MSCAN) SERIAL PERIPHERAL INTERFACE MODULE (SPI) DEBUG MODULE (DBG) SERIAL COMMUNICATIONS INTERFACE (SCI1) VOLTAGE REGULATOR ADP15-ADP8 ADP23-ADP16 6-CHANNEL TIMER/PWM MODULE (TPM1) USER RAM MC9S0DZ60 = 4K REAL-TIME COUNTER (RTC) VDD VDD VSS VSS 8 IRQ RESET ANALOG COMPARATOR (ACMP2) IIC MODULE (IIC) SERIAL COMMUNICATIONS INTERFACE (SCI2) RxCAN TxCAN MISO MOSI SPSCK SS RxD1 TxD1 ACMP2O ACMP2ACMP2+ SDA SCL RxD2 TxD2 MULTI-PURPOSE CLOCK GENERATOR (MCG) XTAL EXTAL OSCILLATOR (XOSC) - VREFH/VREFL internally connected to VDDA/VSSA in 48-pin and 32-pin packages - VDD and VSS pins are each internally connected to two pads in 32-pin package - Pin not connected in 48-pin and 32-pin packages - Pin not connected in 32-pin package Figure 14-1. MC9S08DZ60 Block Diagram MC9S08DZ60 Series Data Sheet, Rev. 4 290 Freescale Semiconductor Chapter 14 Serial Communications Interface (S08SCIV4) 14.1.2 Features Features of SCI module include: * Full-duplex, standard non-return-to-zero (NRZ) format * Double-buffered transmitter and receiver with separate enables * Programmable baud rates (13-bit modulo divider) * Interrupt-driven or polled operation: -- Transmit data register empty and transmission complete -- Receive data register full -- Receive overrun, parity error, framing error, and noise error -- Idle receiver detect -- Active edge on receive pin -- Break detect supporting LIN * Hardware parity generation and checking * Programmable 8-bit or 9-bit character length * Receiver wakeup by idle-line or address-mark * Optional 13-bit break character generation / 11-bit break character detection * Selectable transmitter output polarity 14.1.3 Modes of Operation See Section 14.3, "Functional Description," For details concerning SCI operation in these modes: * 8- and 9-bit data modes * Stop mode operation * Loop mode * Single-wire mode MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 291 Chapter 14 Serial Communications Interface (S08SCIV4) 14.1.4 Block Diagram Figure 14-2 shows the transmitter portion of the SCI. INTERNAL BUS (WRITE-ONLY) LOOPS SCID - Tx BUFFER RSRC LOOP CONTROL STOP M START 11-BIT TRANSMIT SHIFT REGISTER 8 7 6 5 4 3 2 1 0 TO TxD PIN L LSB H 1 x BAUD RATE CLOCK TO RECEIVE DATA IN SHIFT DIRECTION PT BREAK (ALL 0s) PARITY GENERATION PREAMBLE (ALL 1s) PE SHIFT ENABLE T8 LOAD FROM SCIxD TXINV SCI CONTROLS TxD TE SBK TRANSMIT CONTROL TXDIR TxD DIRECTION TO TxD PIN LOGIC BRK13 TDRE TIE TC Tx INTERRUPT REQUEST TCIE Figure 14-2. SCI Transmitter Block Diagram MC9S08DZ60 Series Data Sheet, Rev. 4 292 Freescale Semiconductor Chapter 14 Serial Communications Interface (S08SCIV4) Figure 14-3 shows the receiver portion of the SCI. INTERNAL BUS (READ-ONLY) 16 x BAUD RATE CLOCK DIVIDE BY 16 SCID - Rx BUFFER FROM RxD PIN RXINV LBKDE H DATA RECOVERY WAKE ILT 8 7 6 5 4 3 2 1 START M LSB RSRC 11-BIT RECEIVE SHIFT REGISTER MSB SINGLE-WIRE LOOP CONTROL ALL 1s LOOPS STOP FROM TRANSMITTER 0 L SHIFT DIRECTION WAKEUP LOGIC RWU RWUID ACTIVE EDGE DETECT RDRF RIE IDLE ILIE LBKDIF Rx INTERRUPT REQUEST LBKDIE RXEDGIF RXEDGIE OR ORIE FE FEIE ERROR INTERRUPT REQUEST NF NEIE PE PT PARITY CHECKING PF PEIE Figure 14-3. SCI Receiver Block Diagram MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 293 Chapter 14 Serial Communications Interface (S08SCIV4) 14.2 Register Definition The SCI has eight 8-bit registers to control baud rate, select SCI options, report SCI status, and for transmit/receive data. Refer to the direct-page register summary in the Memory chapter of this data sheet for the absolute address assignments for all SCI registers. This section refers to registers and control bits only by their names. A Freescale-provided equate or header file is used to translate these names into the appropriate absolute addresses. 14.2.1 SCI Baud Rate Registers (SCIxBDH, SCIxBDL) This pair of registers controls the prescale divisor for SCI baud rate generation. To update the 13-bit baud rate setting [SBR12:SBR0], first write to SCIxBDH to buffer the high half of the new value and then write to SCIxBDL. The working value in SCIxBDH does not change until SCIxBDL is written. SCIxBDL is reset to a non-zero value, so after reset the baud rate generator remains disabled until the first time the receiver or transmitter is enabled (RE or TE bits in SCIxC2 are written to 1). 7 6 5 LBKDIE RXEDGIE 0 0 R 4 3 2 1 0 SBR12 SBR11 SBR10 SBR9 SBR8 0 0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 14-4. SCI Baud Rate Register (SCIxBDH) Table 14-2. SCIxBDH Field Descriptions Field 7 LBKDIE Description LIN Break Detect Interrupt Enable (for LBKDIF) 0 Hardware interrupts from LBKDIF disabled (use polling). 1 Hardware interrupt requested when LBKDIF flag is 1. 6 RXEDGIE RxD Input Active Edge Interrupt Enable (for RXEDGIF) 0 Hardware interrupts from RXEDGIF disabled (use polling). 1 Hardware interrupt requested when RXEDGIF flag is 1. 4:0 SBR[12:8] Baud Rate Modulo Divisor -- The 13 bits in SBR[12:0] are referred to collectively as BR, and they set the modulo divide rate for the SCI baud rate generator. When BR = 0, the SCI baud rate generator is disabled to reduce supply current. When BR = 1 to 8191, the SCI baud rate = BUSCLK/(16xBR). See also BR bits in Table 14-3. MC9S08DZ60 Series Data Sheet, Rev. 4 294 Freescale Semiconductor Chapter 14 Serial Communications Interface (S08SCIV4) 7 6 5 4 3 2 1 0 SBR7 SBR6 SBR5 SBR4 SBR3 SBR2 SBR1 SBR0 0 0 0 0 0 1 0 0 R W Reset Figure 14-5. SCI Baud Rate Register (SCIxBDL) Table 14-3. SCIxBDL Field Descriptions Field 7:0 SBR[7:0] 14.2.2 Description Baud Rate Modulo Divisor -- These 13 bits in SBR[12:0] are referred to collectively as BR, and they set the modulo divide rate for the SCI baud rate generator. When BR = 0, the SCI baud rate generator is disabled to reduce supply current. When BR = 1 to 8191, the SCI baud rate = BUSCLK/(16xBR). See also BR bits in Table 14-2. SCI Control Register 1 (SCIxC1) This read/write register is used to control various optional features of the SCI system. 7 6 5 4 3 2 1 0 LOOPS SCISWAI RSRC M WAKE ILT PE PT 0 0 0 0 0 0 0 0 R W Reset Figure 14-6. SCI Control Register 1 (SCIxC1) Table 14-4. SCIxC1 Field Descriptions Field 7 LOOPS 6 SCISWAI 5 RSRC 4 M Description Loop Mode Select -- Selects between loop back modes and normal 2-pin full-duplex modes. When LOOPS = 1, the transmitter output is internally connected to the receiver input. 0 Normal operation -- RxD and TxD use separate pins. 1 Loop mode or single-wire mode where transmitter outputs are internally connected to receiver input. (See RSRC bit.) RxD pin is not used by SCI. SCI Stops in Wait Mode 0 SCI clocks continue to run in wait mode so the SCI can be the source of an interrupt that wakes up the CPU. 1 SCI clocks freeze while CPU is in wait mode. Receiver Source Select -- This bit has no meaning or effect unless the LOOPS bit is set to 1. When LOOPS = 1, the receiver input is internally connected to the TxD pin and RSRC determines whether this connection is also connected to the transmitter output. 0 Provided LOOPS = 1, RSRC = 0 selects internal loop back mode and the SCI does not use the RxD pins. 1 Single-wire SCI mode where the TxD pin is connected to the transmitter output and receiver input. 9-Bit or 8-Bit Mode Select 0 Normal -- start + 8 data bits (LSB first) + stop. 1 Receiver and transmitter use 9-bit data characters start + 8 data bits (LSB first) + 9th data bit + stop. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 295 Chapter 14 Serial Communications Interface (S08SCIV4) Table 14-4. SCIxC1 Field Descriptions (continued) Field 3 WAKE Description Receiver Wakeup Method Select -- Refer to Section 14.3.3.2, "Receiver Wakeup Operation" for more information. 0 Idle-line wakeup. 1 Address-mark wakeup. 2 ILT Idle Line Type Select -- Setting this bit to 1 ensures that the stop bit and logic 1 bits at the end of a character do not count toward the 10 or 11 bit times of logic high level needed by the idle line detection logic. Refer to Section 14.3.3.2.1, "Idle-Line Wakeup" for more information. 0 Idle character bit count starts after start bit. 1 Idle character bit count starts after stop bit. 1 PE Parity Enable -- Enables hardware parity generation and checking. When parity is enabled, the most significant bit (MSB) of the data character (eighth or ninth data bit) is treated as the parity bit. 0 No hardware parity generation or checking. 1 Parity enabled. 0 PT Parity Type -- Provided parity is enabled (PE = 1), this bit selects even or odd parity. Odd parity means the total number of 1s in the data character, including the parity bit, is odd. Even parity means the total number of 1s in the data character, including the parity bit, is even. 0 Even parity. 1 Odd parity. 14.2.3 SCI Control Register 2 (SCIxC2) This register can be read or written at any time. 7 6 5 4 3 2 1 0 TIE TCIE RIE ILIE TE RE RWU SBK 0 0 0 0 0 0 0 0 R W Reset Figure 14-7. SCI Control Register 2 (SCIxC2) Table 14-5. SCIxC2 Field Descriptions Field 7 TIE 6 TCIE Description Transmit Interrupt Enable (for TDRE) 0 Hardware interrupts from TDRE disabled (use polling). 1 Hardware interrupt requested when TDRE flag is 1. Transmission Complete Interrupt Enable (for TC) 0 Hardware interrupts from TC disabled (use polling). 1 Hardware interrupt requested when TC flag is 1. 5 RIE Receiver Interrupt Enable (for RDRF) 0 Hardware interrupts from RDRF disabled (use polling). 1 Hardware interrupt requested when RDRF flag is 1. 4 ILIE Idle Line Interrupt Enable (for IDLE) 0 Hardware interrupts from IDLE disabled (use polling). 1 Hardware interrupt requested when IDLE flag is 1. MC9S08DZ60 Series Data Sheet, Rev. 4 296 Freescale Semiconductor Chapter 14 Serial Communications Interface (S08SCIV4) Table 14-5. SCIxC2 Field Descriptions (continued) Field Description 3 TE Transmitter Enable 0 Transmitter off. 1 Transmitter on. TE must be 1 in order to use the SCI transmitter. When TE = 1, the SCI forces the TxD pin to act as an output for the SCI system. When the SCI is configured for single-wire operation (LOOPS = RSRC = 1), TXDIR controls the direction of traffic on the single SCI communication line (TxD pin). TE also can be used to queue an idle character by writing TE = 0 then TE = 1 while a transmission is in progress. Refer to Section 14.3.2.1, "Send Break and Queued Idle" for more details. When TE is written to 0, the transmitter keeps control of the port TxD pin until any data, queued idle, or queued break character finishes transmitting before allowing the pin to revert to a general-purpose I/O pin. 2 RE Receiver Enable -- When the SCI receiver is off, the RxD pin reverts to being a general-purpose port I/O pin. If LOOPS = 1 the RxD pin reverts to being a general-purpose I/O pin even if RE = 1. 0 Receiver off. 1 Receiver on. 1 RWU Receiver Wakeup Control -- This bit can be written to 1 to place the SCI receiver in a standby state where it waits for automatic hardware detection of a selected wakeup condition. The wakeup condition is either an idle line between messages (WAKE = 0, idle-line wakeup), or a logic 1 in the most significant data bit in a character (WAKE = 1, address-mark wakeup). Application software sets RWU and (normally) a selected hardware condition automatically clears RWU. Refer to Section 14.3.3.2, "Receiver Wakeup Operation" for more details. 0 Normal SCI receiver operation. 1 SCI receiver in standby waiting for wakeup condition. 0 SBK Send Break -- Writing a 1 and then a 0 to SBK queues a break character in the transmit data stream. Additional break characters of 10 or 11 (13 or 14 if BRK13 = 1) bit times of logic 0 are queued as long as SBK = 1. Depending on the timing of the set and clear of SBK relative to the information currently being transmitted, a second break character may be queued before software clears SBK. Refer to Section 14.3.2.1, "Send Break and Queued Idle" for more details. 0 Normal transmitter operation. 1 Queue break character(s) to be sent. 14.2.4 SCI Status Register 1 (SCIxS1) This register has eight read-only status flags. Writes have no effect. Special software sequences (which do not involve writing to this register) are used to clear these status flags. R 7 6 5 4 3 2 1 0 TDRE TC RDRF IDLE OR NF FE PF 1 1 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 14-8. SCI Status Register 1 (SCIxS1) MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 297 Chapter 14 Serial Communications Interface (S08SCIV4) Table 14-6. SCIxS1 Field Descriptions Field Description 7 TDRE Transmit Data Register Empty Flag -- TDRE is set out of reset and when a transmit data value transfers from the transmit data buffer to the transmit shifter, leaving room for a new character in the buffer. To clear TDRE, read SCIxS1 with TDRE = 1 and then write to the SCI data register (SCIxD). 0 Transmit data register (buffer) full. 1 Transmit data register (buffer) empty. 6 TC Transmission Complete Flag -- TC is set out of reset and when TDRE = 1 and no data, preamble, or break character is being transmitted. 0 Transmitter active (sending data, a preamble, or a break). 1 Transmitter idle (transmission activity complete). TC is cleared automatically by reading SCIxS1 with TC = 1 and then doing one of the following three things: * Write to the SCI data register (SCIxD) to transmit new data * Queue a preamble by changing TE from 0 to 1 * Queue a break character by writing 1 to SBK in SCIxC2 5 RDRF Receive Data Register Full Flag -- RDRF becomes set when a character transfers from the receive shifter into the receive data register (SCIxD). To clear RDRF, read SCIxS1 with RDRF = 1 and then read the SCI data register (SCIxD). 0 Receive data register empty. 1 Receive data register full. 4 IDLE Idle Line Flag -- IDLE is set when the SCI receive line becomes idle for a full character time after a period of activity. When ILT = 0, the receiver starts counting idle bit times after the start bit. So if the receive character is all 1s, these bit times and the stop bit time count toward the full character time of logic high (10 or 11 bit times depending on the M control bit) needed for the receiver to detect an idle line. When ILT = 1, the receiver doesn't start counting idle bit times until after the stop bit. So the stop bit and any logic high bit times at the end of the previous character do not count toward the full character time of logic high needed for the receiver to detect an idle line. To clear IDLE, read SCIxS1 with IDLE = 1 and then read the SCI data register (SCIxD). After IDLE has been cleared, it cannot become set again until after a new character has been received and RDRF has been set. IDLE will get set only once even if the receive line remains idle for an extended period. 0 No idle line detected. 1 Idle line was detected. 3 OR Receiver Overrun Flag -- OR is set when a new serial character is ready to be transferred to the receive data register (buffer), but the previously received character has not been read from SCIxD yet. In this case, the new character (and all associated error information) is lost because there is no room to move it into SCIxD. To clear OR, read SCIxS1 with OR = 1 and then read the SCI data register (SCIxD). 0 No overrun. 1 Receive overrun (new SCI data lost). 2 NF Noise Flag -- The advanced sampling technique used in the receiver takes seven samples during the start bit and three samples in each data bit and the stop bit. If any of these samples disagrees with the rest of the samples within any bit time in the frame, the flag NF will be set at the same time as the flag RDRF gets set for the character. To clear NF, read SCIxS1 and then read the SCI data register (SCIxD). 0 No noise detected. 1 Noise detected in the received character in SCIxD. MC9S08DZ60 Series Data Sheet, Rev. 4 298 Freescale Semiconductor Chapter 14 Serial Communications Interface (S08SCIV4) Table 14-6. SCIxS1 Field Descriptions (continued) Field Description 1 FE Framing Error Flag -- FE is set at the same time as RDRF when the receiver detects a logic 0 where the stop bit was expected. This suggests the receiver was not properly aligned to a character frame. To clear FE, read SCIxS1 with FE = 1 and then read the SCI data register (SCIxD). 0 No framing error detected. This does not guarantee the framing is correct. 1 Framing error. 0 PF Parity Error Flag -- PF is set at the same time as RDRF when parity is enabled (PE = 1) and the parity bit in the received character does not agree with the expected parity value. To clear PF, read SCIxS1 and then read the SCI data register (SCIxD). 0 No parity error. 1 Parity error. 14.2.5 SCI Status Register 2 (SCIxS2) This register has one read-only status flag. 7 6 LBKDIF RXEDGIF 0 0 R 5 4 3 2 1 RXINV RWUID BRK13 LBKDE 0 0 0 0 0 0 RAF W Reset 0 0 = Unimplemented or Reserved Figure 14-9. SCI Status Register 2 (SCIxS2) Table 14-7. SCIxS2 Field Descriptions Field Description 7 LBKDIF LIN Break Detect Interrupt Flag -- LBKDIF is set when the LIN break detect circuitry is enabled and a LIN break character is detected. LBKDIF is cleared by writing a "1" to it. 0 No LIN break character has been detected. 1 LIN break character has been detected. 6 RXEDGIF RxD Pin Active Edge Interrupt Flag -- RXEDGIF is set when an active edge (falling if RXINV = 0, rising if RXINV=1) on the RxD pin occurs. RXEDGIF is cleared by writing a "1" to it. 0 No active edge on the receive pin has occurred. 1 An active edge on the receive pin has occurred. 4 RXINV1 Receive Data Inversion -- Setting this bit reverses the polarity of the received data input. 0 Receive data not inverted 1 Receive data inverted 3 RWUID Receive Wake Up Idle Detect-- RWUID controls whether the idle character that wakes up the receiver sets the IDLE bit. 0 During receive standby state (RWU = 1), the IDLE bit does not get set upon detection of an idle character. 1 During receive standby state (RWU = 1), the IDLE bit gets set upon detection of an idle character. 2 BRK13 Break Character Generation Length -- BRK13 is used to select a longer transmitted break character length. Detection of a framing error is not affected by the state of this bit. 0 Break character is transmitted with length of 10 bit times (11 if M = 1) 1 Break character is transmitted with length of 13 bit times (14 if M = 1) MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 299 Chapter 14 Serial Communications Interface (S08SCIV4) Table 14-7. SCIxS2 Field Descriptions (continued) Field 1 LBKDE 0 RAF 1 Description LIN Break Detection Enable-- LBKDE is used to select a longer break character detection length. While LBKDE is set, framing error (FE) and receive data register full (RDRF) flags are prevented from setting. 0 Break character is detected at length of 10 bit times (11 if M = 1). 1 Break character is detected at length of 11 bit times (12 if M = 1). Receiver Active Flag -- RAF is set when the SCI receiver detects the beginning of a valid start bit, and RAF is cleared automatically when the receiver detects an idle line. This status flag can be used to check whether an SCI character is being received before instructing the MCU to go to stop mode. 0 SCI receiver idle waiting for a start bit. 1 SCI receiver active (RxD input not idle). Setting RXINV inverts the RxD input for all cases: data bits, start and stop bits, break, and idle. When using an internal oscillator in a LIN system, it is necessary to raise the break detection threshold by one bit time. Under the worst case timing conditions allowed in LIN, it is possible that a 0x00 data character can appear to be 10.26 bit times long at a slave which is running 14% faster than the master. This would trigger normal break detection circuitry which is designed to detect a 10 bit break symbol. When the LBKDE bit is set, framing errors are inhibited and the break detection threshold changes from 10 bits to 11 bits, preventing false detection of a 0x00 data character as a LIN break symbol. 14.2.6 SCI Control Register 3 (SCIxC3) 7 R 6 5 4 3 2 1 0 T8 TXDIR TXINV ORIE NEIE FEIE PEIE 0 0 0 0 0 0 0 R8 W Reset 0 = Unimplemented or Reserved Figure 14-10. SCI Control Register 3 (SCIxC3) Table 14-8. SCIxC3 Field Descriptions Field Description 7 R8 Ninth Data Bit for Receiver -- When the SCI is configured for 9-bit data (M = 1), R8 can be thought of as a ninth receive data bit to the left of the MSB of the buffered data in the SCIxD register. When reading 9-bit data, read R8 before reading SCIxD because reading SCIxD completes automatic flag clearing sequences which could allow R8 and SCIxD to be overwritten with new data. 6 T8 Ninth Data Bit for Transmitter -- When the SCI is configured for 9-bit data (M = 1), T8 may be thought of as a ninth transmit data bit to the left of the MSB of the data in the SCIxD register. When writing 9-bit data, the entire 9-bit value is transferred to the SCI shift register after SCIxD is written so T8 should be written (if it needs to change from its previous value) before SCIxD is written. If T8 does not need to change in the new value (such as when it is used to generate mark or space parity), it need not be written each time SCIxD is written. 5 TXDIR TxD Pin Direction in Single-Wire Mode -- When the SCI is configured for single-wire half-duplex operation (LOOPS = RSRC = 1), this bit determines the direction of data at the TxD pin. 0 TxD pin is an input in single-wire mode. 1 TxD pin is an output in single-wire mode. MC9S08DZ60 Series Data Sheet, Rev. 4 300 Freescale Semiconductor Chapter 14 Serial Communications Interface (S08SCIV4) Table 14-8. SCIxC3 Field Descriptions (continued) Field 4 TXINV1 1 Description Transmit Data Inversion -- Setting this bit reverses the polarity of the transmitted data output. 0 Transmit data not inverted 1 Transmit data inverted 3 ORIE Overrun Interrupt Enable -- This bit enables the overrun flag (OR) to generate hardware interrupt requests. 0 OR interrupts disabled (use polling). 1 Hardware interrupt requested when OR = 1. 2 NEIE Noise Error Interrupt Enable -- This bit enables the noise flag (NF) to generate hardware interrupt requests. 0 NF interrupts disabled (use polling). 1 Hardware interrupt requested when NF = 1. 1 FEIE Framing Error Interrupt Enable -- This bit enables the framing error flag (FE) to generate hardware interrupt requests. 0 FE interrupts disabled (use polling). 1 Hardware interrupt requested when FE = 1. 0 PEIE Parity Error Interrupt Enable -- This bit enables the parity error flag (PF) to generate hardware interrupt requests. 0 PF interrupts disabled (use polling). 1 Hardware interrupt requested when PF = 1. Setting TXINV inverts the TxD output for all cases: data bits, start and stop bits, break, and idle. 14.2.7 SCI Data Register (SCIxD) This register is actually two separate registers. Reads return the contents of the read-only receive data buffer and writes go to the write-only transmit data buffer. Reads and writes of this register are also involved in the automatic flag clearing mechanisms for the SCI status flags. 7 6 5 4 3 2 1 0 R R7 R6 R5 R4 R3 R2 R1 R0 W T7 T6 T5 T4 T3 T2 T1 T0 0 0 0 0 0 0 0 0 Reset Figure 14-11. SCI Data Register (SCIxD) 14.3 Functional Description The SCI allows full-duplex, asynchronous, NRZ serial communication among the MCU and remote devices, including other MCUs. The SCI comprises a baud rate generator, transmitter, and receiver block. The transmitter and receiver operate independently, although they use the same baud rate generator. During normal operation, the MCU monitors the status of the SCI, writes the data to be transmitted, and processes received data. The following describes each of the blocks of the SCI. 14.3.1 Baud Rate Generation As shown in Figure 14-12, the clock source for the SCI baud rate generator is the bus-rate clock. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 301 Chapter 14 Serial Communications Interface (S08SCIV4) MODULO DIVIDE BY (1 THROUGH 8191) BUSCLK SBR12:SBR0 BAUD RATE GENERATOR OFF IF [SBR12:SBR0] = 0 DIVIDE BY 16 Tx BAUD RATE Rx SAMPLING CLOCK (16 x BAUD RATE) BAUD RATE = BUSCLK [SBR12:SBR0] x 16 Figure 14-12. SCI Baud Rate Generation SCI communications require the transmitter and receiver (which typically derive baud rates from independent clock sources) to use the same baud rate. Allowed tolerance on this baud frequency depends on the details of how the receiver synchronizes to the leading edge of the start bit and how bit sampling is performed. The MCU resynchronizes to bit boundaries on every high-to-low transition, but in the worst case, there are no such transitions in the full 10- or 11-bit time character frame so any mismatch in baud rate is accumulated for the whole character time. For a Freescale Semiconductor SCI system whose bus frequency is driven by a crystal, the allowed baud rate mismatch is about 4.5percent for 8-bit data format and about 4 percent for 9-bit data format. Although baud rate modulo divider settings do not always produce baud rates that exactly match standard rates, it is normally possible to get within a few percent, which is acceptable for reliable communications. 14.3.2 Transmitter Functional Description This section describes the overall block diagram for the SCI transmitter, as well as specialized functions for sending break and idle characters. The transmitter block diagram is shown in Figure 14-2. The transmitter output (TxD) idle state defaults to logic high (TXINV = 0 following reset). The transmitter output is inverted by setting TXINV = 1. The transmitter is enabled by setting the TE bit in SCIxC2. This queues a preamble character that is one full character frame of the idle state. The transmitter then remains idle until data is available in the transmit data buffer. Programs store data into the transmit data buffer by writing to the SCI data register (SCIxD). The central element of the SCI transmitter is the transmit shift register that is either 10 or 11 bits long depending on the setting in the M control bit. For the remainder of this section, we will assume M = 0, selecting the normal 8-bit data mode. In 8-bit data mode, the shift register holds a start bit, eight data bits, and a stop bit. When the transmit shift register is available for a new SCI character, the value waiting in the transmit data register is transferred to the shift register (synchronized with the baud rate clock) and the transmit data register empty (TDRE) status flag is set to indicate another character may be written to the transmit data buffer at SCIxD. If no new character is waiting in the transmit data buffer after a stop bit is shifted out the TxD pin, the transmitter sets the transmit complete flag and enters an idle mode, with TxD high, waiting for more characters to transmit. MC9S08DZ60 Series Data Sheet, Rev. 4 302 Freescale Semiconductor Chapter 14 Serial Communications Interface (S08SCIV4) Writing 0 to TE does not immediately release the pin to be a general-purpose I/O pin. Any transmit activity that is in progress must first be completed. This includes data characters in progress, queued idle characters, and queued break characters. 14.3.2.1 Send Break and Queued Idle The SBK control bit in SCIxC2 is used to send break characters which were originally used to gain the attention of old teletype receivers. Break characters are a full character time of logic 0 (10 bit times including the start and stop bits). A longer break of 13 bit times can be enabled by setting BRK13 = 1. Normally, a program would wait for TDRE to become set to indicate the last character of a message has moved to the transmit shifter, then write 1 and then write 0 to the SBK bit. This action queues a break character to be sent as soon as the shifter is available. If SBK is still 1 when the queued break moves into the shifter (synchronized to the baud rate clock), an additional break character is queued. If the receiving device is another Freescale Semiconductor SCI, the break characters will be received as 0s in all eight data bits and a framing error (FE = 1) occurs. When idle-line wakeup is used, a full character time of idle (logic 1) is needed between messages to wake up any sleeping receivers. Normally, a program would wait for TDRE to become set to indicate the last character of a message has moved to the transmit shifter, then write 0 and then write 1 to the TE bit. This action queues an idle character to be sent as soon as the shifter is available. As long as the character in the shifter does not finish while TE = 0, the SCI transmitter never actually releases control of the TxD pin. If there is a possibility of the shifter finishing while TE = 0, set the general-purpose I/O controls so the pin that is shared with TxD is an output driving a logic 1. This ensures that the TxD line will look like a normal idle line even if the SCI loses control of the port pin between writing 0 and then 1 to TE. The length of the break character is affected by the BRK13 and M bits as shown below. Table 14-9. Break Character Length 14.3.3 BRK13 M Break Character Length 0 0 10 bit times 0 1 11 bit times 1 0 13 bit times 1 1 14 bit times Receiver Functional Description In this section, the receiver block diagram (Figure 14-3) is used as a guide for the overall receiver functional description. Next, the data sampling technique used to reconstruct receiver data is described in more detail. Finally, two variations of the receiver wakeup function are explained. The receiver input is inverted by setting RXINV = 1. The receiver is enabled by setting the RE bit in SCIxC2. Character frames consist of a start bit of logic 0, eight (or nine) data bits (LSB first), and a stop bit of logic 1. For information about 9-bit data mode, refer to Section 14.3.5.1, "8- and 9-Bit Data Modes." For the remainder of this discussion, we assume the SCI is configured for normal 8-bit data mode. After receiving the stop bit into the receive shifter, and provided the receive data register is not already full, the data character is transferred to the receive data register and the receive data register full (RDRF) status MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 303 Chapter 14 Serial Communications Interface (S08SCIV4) flag is set. If RDRF was already set indicating the receive data register (buffer) was already full, the overrun (OR) status flag is set and the new data is lost. Because the SCI receiver is double-buffered, the program has one full character time after RDRF is set before the data in the receive data buffer must be read to avoid a receiver overrun. When a program detects that the receive data register is full (RDRF = 1), it gets the data from the receive data register by reading SCIxD. The RDRF flag is cleared automatically by a 2-step sequence which is normally satisfied in the course of the user's program that handles receive data. Refer to Section 14.3.4, "Interrupts and Status Flags" for more details about flag clearing. 14.3.3.1 Data Sampling Technique The SCI receiver uses a 16x baud rate clock for sampling. The receiver starts by taking logic level samples at 16 times the baud rate to search for a falling edge on the RxD serial data input pin. A falling edge is defined as a logic 0 sample after three consecutive logic 1 samples. The 16x baud rate clock is used to divide the bit time into 16 segments labeled RT1 through RT16. When a falling edge is located, three more samples are taken at RT3, RT5, and RT7 to make sure this was a real start bit and not merely noise. If at least two of these three samples are 0, the receiver assumes it is synchronized to a receive character. The receiver then samples each bit time, including the start and stop bits, at RT8, RT9, and RT10 to determine the logic level for that bit. The logic level is interpreted to be that of the majority of the samples taken during the bit time. In the case of the start bit, the bit is assumed to be 0 if at least two of the samples at RT3, RT5, and RT7 are 0 even if one or all of the samples taken at RT8, RT9, and RT10 are 1s. If any sample in any bit time (including the start and stop bits) in a character frame fails to agree with the logic level for that bit, the noise flag (NF) will be set when the received character is transferred to the receive data buffer. The falling edge detection logic continuously looks for falling edges, and if an edge is detected, the sample clock is resynchronized to bit times. This improves the reliability of the receiver in the presence of noise or mismatched baud rates. It does not improve worst case analysis because some characters do not have any extra falling edges anywhere in the character frame. In the case of a framing error, provided the received character was not a break character, the sampling logic that searches for a falling edge is filled with three logic 1 samples so that a new start bit can be detected almost immediately. In the case of a framing error, the receiver is inhibited from receiving any new characters until the framing error flag is cleared. The receive shift register continues to function, but a complete character cannot transfer to the receive data buffer if FE is still set. 14.3.3.2 Receiver Wakeup Operation Receiver wakeup is a hardware mechanism that allows an SCI receiver to ignore the characters in a message that is intended for a different SCI receiver. In such a system, all receivers evaluate the first character(s) of each message, and as soon as they determine the message is intended for a different receiver, they write logic 1 to the receiver wake up (RWU) control bit in SCIxC2. When RWU bit is set, the status flags associated with the receiver (with the exception of the idle bit, IDLE, when RWUID bit is set) are inhibited from setting, thus eliminating the software overhead for handling the unimportant MC9S08DZ60 Series Data Sheet, Rev. 4 304 Freescale Semiconductor Chapter 14 Serial Communications Interface (S08SCIV4) message characters. At the end of a message, or at the beginning of the next message, all receivers automatically force RWU to 0 so all receivers wake up in time to look at the first character(s) of the next message. 14.3.3.2.1 Idle-Line Wakeup When WAKE = 0, the receiver is configured for idle-line wakeup. In this mode, RWU is cleared automatically when the receiver detects a full character time of the idle-line level. The M control bit selects 8-bit or 9-bit data mode that determines how many bit times of idle are needed to constitute a full character time (10 or 11 bit times because of the start and stop bits). When RWU is one and RWUID is zero, the idle condition that wakes up the receiver does not set the IDLE flag. The receiver wakes up and waits for the first data character of the next message which will set the RDRF flag and generate an interrupt if enabled. When RWUID is one, any idle condition sets the IDLE flag and generates an interrupt if enabled, regardless of whether RWU is zero or one. The idle-line type (ILT) control bit selects one of two ways to detect an idle line. When ILT = 0, the idle bit counter starts after the start bit so the stop bit and any logic 1s at the end of a character count toward the full character time of idle. When ILT = 1, the idle bit counter does not start until after a stop bit time, so the idle detection is not affected by the data in the last character of the previous message. 14.3.3.2.2 Address-Mark Wakeup When WAKE = 1, the receiver is configured for address-mark wakeup. In this mode, RWU is cleared automatically when the receiver detects a logic 1 in the most significant bit of a received character (eighth bit in M = 0 mode and ninth bit in M = 1 mode). Address-mark wakeup allows messages to contain idle characters but requires that the MSB be reserved for use in address frames. The logic 1 MSB of an address frame clears the RWU bit before the stop bit is received and sets the RDRF flag. In this case the character with the MSB set is received even though the receiver was sleeping during most of this character time. 14.3.4 Interrupts and Status Flags The SCI system has three separate interrupt vectors to reduce the amount of software needed to isolate the cause of the interrupt. One interrupt vector is associated with the transmitter for TDRE and TC events. Another interrupt vector is associated with the receiver for RDRF, IDLE, RXEDGIF and LBKDIF events, and a third vector is used for OR, NF, FE, and PF error conditions. Each of these ten interrupt sources can be separately masked by local interrupt enable masks. The flags can still be polled by software when the local masks are cleared to disable generation of hardware interrupt requests. The SCI transmitter has two status flags that optionally can generate hardware interrupt requests. Transmit data register empty (TDRE) indicates when there is room in the transmit data buffer to write another transmit character to SCIxD. If the transmit interrupt enable (TIE) bit is set, a hardware interrupt will be requested whenever TDRE = 1. Transmit complete (TC) indicates that the transmitter is finished transmitting all data, preamble, and break characters and is idle with TxD at the inactive level. This flag is often used in systems with modems to determine when it is safe to turn off the modem. If the transmit complete interrupt enable (TCIE) bit is set, a hardware interrupt will be requested whenever TC = 1. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 305 Chapter 14 Serial Communications Interface (S08SCIV4) Instead of hardware interrupts, software polling may be used to monitor the TDRE and TC status flags if the corresponding TIE or TCIE local interrupt masks are 0s. When a program detects that the receive data register is full (RDRF = 1), it gets the data from the receive data register by reading SCIxD. The RDRF flag is cleared by reading SCIxS1 while RDRF = 1 and then reading SCIxD. When polling is used, this sequence is naturally satisfied in the normal course of the user program. If hardware interrupts are used, SCIxS1 must be read in the interrupt service routine (ISR). Normally, this is done in the ISR anyway to check for receive errors, so the sequence is automatically satisfied. The IDLE status flag includes logic that prevents it from getting set repeatedly when the RxD line remains idle for an extended period of time. IDLE is cleared by reading SCIxS1 while IDLE = 1 and then reading SCIxD. After IDLE has been cleared, it cannot become set again until the receiver has received at least one new character and has set RDRF. If the associated error was detected in the received character that caused RDRF to be set, the error flags -- noise flag (NF), framing error (FE), and parity error flag (PF) -- get set at the same time as RDRF. These flags are not set in overrun cases. If RDRF was already set when a new character is ready to be transferred from the receive shifter to the receive data buffer, the overrun (OR) flag gets set instead the data along with any associated NF, FE, or PF condition is lost. At any time, an active edge on the RxD serial data input pin causes the RXEDGIF flag to set. The RXEDGIF flag is cleared by writing a "1" to it. This function does depend on the receiver being enabled (RE = 1). 14.3.5 Additional SCI Functions The following sections describe additional SCI functions. 14.3.5.1 8- and 9-Bit Data Modes The SCI system (transmitter and receiver) can be configured to operate in 9-bit data mode by setting the M control bit in SCIxC1. In 9-bit mode, there is a ninth data bit to the left of the MSB of the SCI data register. For the transmit data buffer, this bit is stored in T8 in SCIxC3. For the receiver, the ninth bit is held in R8 in SCIxC3. For coherent writes to the transmit data buffer, write to the T8 bit before writing to SCIxD. If the bit value to be transmitted as the ninth bit of a new character is the same as for the previous character, it is not necessary to write to T8 again. When data is transferred from the transmit data buffer to the transmit shifter, the value in T8 is copied at the same time data is transferred from SCIxD to the shifter. 9-bit data mode typically is used in conjunction with parity to allow eight bits of data plus the parity in the ninth bit. Or it is used with address-mark wakeup so the ninth data bit can serve as the wakeup bit. In custom protocols, the ninth bit can also serve as a software-controlled marker. MC9S08DZ60 Series Data Sheet, Rev. 4 306 Freescale Semiconductor Chapter 14 Serial Communications Interface (S08SCIV4) 14.3.5.2 Stop Mode Operation During all stop modes, clocks to the SCI module are halted. In stop1 and stop2 modes, all SCI register data is lost and must be re-initialized upon recovery from these two stop modes. No SCI module registers are affected in stop3 mode. The receive input active edge detect circuit is still active in stop3 mode, but not in stop2.. An active edge on the receive input brings the CPU out of stop3 mode if the interrupt is not masked (RXEDGIE = 1). Note, because the clocks are halted, the SCI module will resume operation upon exit from stop (only in stop3 mode). Software should ensure stop mode is not entered while there is a character being transmitted out of or received into the SCI module. 14.3.5.3 Loop Mode When LOOPS = 1, the RSRC bit in the same register chooses between loop mode (RSRC = 0) or single-wire mode (RSRC = 1). Loop mode is sometimes used to check software, independent of connections in the external system, to help isolate system problems. In this mode, the transmitter output is internally connected to the receiver input and the RxD pin is not used by the SCI, so it reverts to a general-purpose port I/O pin. 14.3.5.4 Single-Wire Operation When LOOPS = 1, the RSRC bit in the same register chooses between loop mode (RSRC = 0) or single-wire mode (RSRC = 1). Single-wire mode is used to implement a half-duplex serial connection. The receiver is internally connected to the transmitter output and to the TxD pin. The RxD pin is not used and reverts to a general-purpose port I/O pin. In single-wire mode, the TXDIR bit in SCIxC3 controls the direction of serial data on the TxD pin. When TXDIR = 0, the TxD pin is an input to the SCI receiver and the transmitter is temporarily disconnected from the TxD pin so an external device can send serial data to the receiver. When TXDIR = 1, the TxD pin is an output driven by the transmitter. In single-wire mode, the internal loop back connection from the transmitter to the receiver causes the receiver to receive characters that are sent out by the transmitter. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 307 Chapter 14 Serial Communications Interface (S08SCIV4) MC9S08DZ60 Series Data Sheet, Rev. 4 308 Freescale Semiconductor Chapter 15 Real-Time Counter (S08RTCV1) 15.1 Introduction The RTC module consists of one 8-bit counter, one 8-bit comparator, several binary-based and decimal-based prescaler dividers, three clock sources, and one programmable periodic interrupt. This module can be used for time-of-day, calendar or any task scheduling functions. It can also serve as a cyclic wake up from low power modes without the need of external components. All devices in the MC9S08DZ60 Series feature the RTC. 15.1.1 RTC Clock Signal Names References to ERCLK and IRCLK in this chapter correspond to signals MCGERCLK and MCGIRCLK, respectively. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 309 PORT A PTA7/PIA7/ADP7/IRQ PTA6/PIA6/ADP6 PTA5/PIA5/ADP5 PTA4/PIA4/ADP4 PTA3/PIA3/ADP3/ACMP1O PTA2/PIA2/ADP2/ACMP1PTA1/PIA1/ADP1/ACMP1+ PTA0/PIA0/ADP0/MCLK PORT B PTB7/PIB7/ADP15 PTB6/PIB6/ADP14 PTB5/PIB5/ADP13 PTB4/PIB4/ADP12 PTB3/PIB3/ADP11 PTB2/PIB2/ADP10 PTB1/PIB1/ADP9 PTB0/PIB0/ADP8 PORT C PTC7/ADP23 PTC6/ADP22 PTC5/ADP21 PTC4/ADP20 PTC3/ADP19 PTC2/ADP18 PTC1/ADP17 PTC0/ADP16 PORT D PTD7/PID7/TPM1CH5 PTD6/PID6/TPM1CH4 PTD5/PID5/TPM1CH3 PTD4/PID4/TPM1CH2 PTD3/PID3/TPM1CH1 PTD2/PID2/TPM1CH0 PTD1/PID1/TPM2CH1 PTD0/PID0/TPM2CH0 PORT E PTE7/RxD2/RXCAN PTE6/TxD2/TXCAN PTE5/SDA/MISO PTE4/SCL/MOSI PTE3/SPSCK PTE2/SS PTE1/RxD1 PTE0/TxD1 PORT F PTF7 PTF6/ACMP2O PTF5/ACMP2PTF4/ACMP2+ PTF3/TPM2CLK/SDA PTF2/TPM1CLK/SCL PTF1/RxD2 PTF0/TxD2 PORT G Chapter 15 Real-Time Counter (S08RTCV1) PTG5 PTG4 PTG3 PTG2 PTG1/XTAL PTG0/EXTAL HCS08 CORE CPU BKGD/MS BDC ANALOG COMPARATOR (ACMP1) BKP ACMP1O ACMP1ACMP1+ HCS08 SYSTEM CONTROL RESETS AND INTERRUPTS MODES OF OPERATION POWER MANAGEMENT COP LVD INT IRQ ADP7-ADP0 24-CHANNEL,12-BIT ANALOG-TO-DIGITAL CONVERTER (ADC) VREFH VREFL VDDA VSSA USER FLASH MC9S0DZ60 = 60K MC9S0DZ48 = 48K MC9S0DZ32 = 32K MC9S0DZ16 = 16K USER EEPROM MC9S0DZ60 = 2K TPM1CH5 TPM1CH0 6 TPM1CLK 2-CHANNEL TIMER/PWM MODULE (TPM2) TPM2CH1, TPM2CH0 TPM2CLK CONTROLLER AREA NETWORK (MSCAN) SERIAL PERIPHERAL INTERFACE MODULE (SPI) DEBUG MODULE (DBG) SERIAL COMMUNICATIONS INTERFACE (SCI1) VOLTAGE REGULATOR ADP15-ADP8 ADP23-ADP16 6-CHANNEL TIMER/PWM MODULE (TPM1) USER RAM MC9S0DZ60 = 4K REAL-TIME COUNTER (RTC) VDD VDD VSS VSS 8 IRQ RESET ANALOG COMPARATOR (ACMP2) IIC MODULE (IIC) SERIAL COMMUNICATIONS INTERFACE (SCI2) RxCAN TxCAN MISO MOSI SPSCK SS RxD1 TxD1 ACMP2O ACMP2ACMP2+ SDA SCL RxD2 TxD2 MULTI-PURPOSE CLOCK GENERATOR (MCG) XTAL EXTAL OSCILLATOR (XOSC) - VREFH/VREFL internally connected to VDDA/VSSA in 48-pin and 32-pin packages - VDD and VSS pins are each internally connected to two pads in 32-pin package - Pin not connected in 48-pin and 32-pin packages - Pin not connected in 32-pin package Figure 15-1. MC9S08DZ60 Block Diagram MC9S08DZ60 Series Data Sheet, Rev. 4 310 Freescale Semiconductor Chapter 15 Real-Time Counter (S08RTCV1) 15.1.2 Features Features of the RTC module include: * 8-bit up-counter -- 8-bit modulo match limit -- Software controllable periodic interrupt on match * Three software selectable clock sources for input to prescaler with selectable binary-based and decimal-based divider values -- 1-kHz internal low-power oscillator (LPO) -- External clock (ERCLK) -- 32-kHz internal clock (IRCLK) 15.1.3 Modes of Operation This section defines the operation in stop, wait and background debug modes. 15.1.3.1 Wait Mode The RTC continues to run in wait mode if enabled before executing the appropriate instruction. Therefore, the RTC can bring the MCU out of wait mode if the real-time interrupt is enabled. For lowest possible current consumption, the RTC should be stopped by software if not needed as an interrupt source during wait mode. 15.1.3.2 Stop Modes The RTC continues to run in stop2 or stop3 mode if the RTC is enabled before executing the STOP instruction. Therefore, the RTC can bring the MCU out of stop modes with no external components, if the real-time interrupt is enabled. The LPO clock can be used in stop2 and stop3 modes. ERCLK and IRCLK clocks are only available in stop3 mode. Power consumption is lower when all clock sources are disabled, but in that case, the real-time interrupt cannot wake up the MCU from stop modes. 15.1.3.3 Active Background Mode The RTC suspends all counting during active background mode until the microcontroller returns to normal user operating mode. Counting resumes from the suspended value as long as the RTCMOD register is not written and the RTCPS and RTCLKS bits are not altered. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 311 Chapter 15 Real-Time Counter (S08RTCV1) 15.1.4 Block Diagram The block diagram for the RTC module is shown in Figure 15-2. LPO Clock Source Select ERCLK IRCLK 8-Bit Modulo (RTCMOD) RTCLKS VDD RTCLKS[0] RTCPS Prescaler Divide-By Q D Background Mode E 8-Bit Comparator RTC Clock RTC Interrupt Request RTIF R Write 1 to RTIF 8-Bit Counter (RTCCNT) RTIE Figure 15-2. Real-Time Counter (RTC) Block Diagram 15.2 External Signal Description The RTC does not include any off-chip signals. 15.3 Register Definition The RTC includes a status and control register, an 8-bit counter register, and an 8-bit modulo register. Refer to the direct-page register summary in the memory section of this document for the absolute address assignments for all RTC registers.This section refers to registers and control bits only by their names and relative address offsets. Table 15-1 is a summary of RTC registers. Table 15-1. RTC Register Summary Name 7 6 5 4 3 2 1 0 R RTCSC RTIF RTCLKS RTIE RTCPS W R RTCCNT RTCCNT W R RTCMOD RTCMOD W MC9S08DZ60 Series Data Sheet, Rev. 4 312 Freescale Semiconductor Chapter 15 Real-Time Counter (S08RTCV1) 15.3.1 RTC Status and Control Register (RTCSC) RTCSC contains the real-time interrupt status flag (RTIF), the clock select bits (RTCLKS), the real-time interrupt enable bit (RTIE), and the prescaler select bits (RTCPS). 7 6 5 4 3 2 1 0 0 0 R RTIF RTCLKS RTIE RTCPS W Reset: 0 0 0 0 0 0 Figure 15-3. RTC Status and Control Register (RTCSC) Table 15-2. RTCSC Field Descriptions Field Description 7 RTIF Real-Time Interrupt Flag This status bit indicates the RTC counter register reached the value in the RTC modulo register. Writing a logic 0 has no effect. Writing a logic 1 clears the bit and the real-time interrupt request. Reset clears RTIF. 0 RTC counter has not reached the value in the RTC modulo register. 1 RTC counter has reached the value in the RTC modulo register. 6-5 RTCLKS Real-Time Clock Source Select. These two read/write bits select the clock source input to the RTC prescaler. Changing the clock source clears the prescaler and RTCCNT counters. When selecting a clock source, ensure that the clock source is properly enabled (if applicable) to ensure correct operation of the RTC. Reset clears RTCLKS. 00 Real-time clock source is the 1-kHz low power oscillator (LPO) 01 Real-time clock source is the external clock (ERCLK) 1x Real-time clock source is the internal clock (IRCLK) 4 RTIE Real-Time Interrupt Enable. This read/write bit enables real-time interrupts. If RTIE is set, then an interrupt is generated when RTIF is set. Reset clears RTIE. 0 Real-time interrupt requests are disabled. Use software polling. 1 Real-time interrupt requests are enabled. 3-0 RTCPS Real-Time Clock Prescaler Select. These four read/write bits select binary-based or decimal-based divide-by values for the clock source. See Table 15-3. Changing the prescaler value clears the prescaler and RTCCNT counters. Reset clears RTCPS. Table 15-3. RTC Prescaler Divide-by values RTCPS RTCLKS[0] 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0 Off 23 25 26 27 28 29 210 1 2 22 10 24 102 5x102 103 1 Off 210 211 212 213 214 215 216 103 105 2x105 2x103 5x103 104 2x104 5x104 MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 313 Chapter 15 Real-Time Counter (S08RTCV1) 15.3.2 RTC Counter Register (RTCCNT) RTCCNT is the read-only value of the current RTC count of the 8-bit counter. 7 6 5 4 R 3 2 1 0 0 0 0 0 RTCCNT W Reset: 0 0 0 0 Figure 15-4. RTC Counter Register (RTCCNT) Table 15-4. RTCCNT Field Descriptions Field Description 7:0 RTCCNT RTC Count. These eight read-only bits contain the current value of the 8-bit counter. Writes have no effect to this register. Reset, writing to RTCMOD, or writing different values to RTCLKS and RTCPS clear the count to 0x00. 15.3.3 RTC Modulo Register (RTCMOD) 7 6 5 4 3 2 1 0 0 0 0 0 R RTCMOD W Reset: 0 0 0 0 Figure 15-5. RTC Modulo Register (RTCMOD) Table 15-5. RTCMOD Field Descriptions Field Description 7:0 RTC Modulo. These eight read/write bits contain the modulo value used to reset the count to 0x00 upon a compare RTCMOD match and set the RTIF status bit. A value of 0x00 sets the RTIF bit on each rising edge of the prescaler output. Writing to RTCMOD resets the prescaler and the RTCCNT counters to 0x00. Reset sets the modulo to 0x00. 15.4 Functional Description The RTC is composed of a main 8-bit up-counter with an 8-bit modulo register, a clock source selector, and a prescaler block with binary-based and decimal-based selectable values. The module also contains software selectable interrupt logic. After any MCU reset, the counter is stopped and reset to 0x00, the modulus register is set to 0x00, and the prescaler is off. The 1-kHz internal oscillator clock is selected as the default clock source. To start the prescaler, write any value other than zero to the prescaler select bits (RTCPS). Three clock sources are software selectable: the low power oscillator clock (LPO), the external clock (ERCLK), and the internal clock (IRCLK). The RTC clock select bits (RTCLKS) select the desired clock source. If a different value is written to RTCLKS, the prescaler and RTCCNT counters are reset to 0x00. MC9S08DZ60 Series Data Sheet, Rev. 4 314 Freescale Semiconductor Chapter 15 Real-Time Counter (S08RTCV1) RTCPS and the RTCLKS[0] bit select the desired divide-by value. If a different value is written to RTCPS, the prescaler and RTCCNT counters are reset to 0x00. Table 15-6 shows different prescaler period values. Table 15-6. Prescaler Period RTCPS 1-kHz Internal Clock (RTCLKS = 00) 1-MHz External Clock 32-kHz Internal Clock 32-kHz Internal Clock (RTCLKS = 01) (RTCLKS = 10) (RTCLKS = 11) 0000 Off Off Off Off 0001 8 ms 1.024 ms 250 s 32 ms 0010 32 ms 2.048 ms 1 ms 64 ms 0011 64 ms 4.096 ms 2 ms 128 ms 0100 128 ms 8.192 ms 4 ms 256 ms 0101 256 ms 16.4 ms 8 ms 512 ms 0110 512 ms 32.8 ms 16 ms 1.024 s 0111 1.024 s 65.5 ms 32 ms 2.048 s 1000 1 ms 1 ms 31.25 s 31.25 ms 1001 2 ms 2 ms 62.5 s 62.5 ms 1010 4 ms 5 ms 125 s 156.25 ms 1011 10 ms 10 ms 312.5 s 312.5 ms 1100 16 ms 20 ms 0.5 ms 0.625 s 1101 0.1 s 50 ms 3.125 ms 1.5625 s 1110 0.5 s 0.1 s 15.625 ms 3.125 s 1111 1s 0.2 s 31.25 ms 6.25 s The RTC modulo register (RTCMOD) allows the compare value to be set to any value from 0x00 to 0xFF. When the counter is active, the counter increments at the selected rate until the count matches the modulo value. When these values match, the counter resets to 0x00 and continues counting. The real-time interrupt flag (RTIF) is set when a match occurs. The flag sets on the transition from the modulo value to 0x00. Writing to RTCMOD resets the prescaler and the RTCCNT counters to 0x00. The RTC allows for an interrupt to be generated when RTIF is set. To enable the real-time interrupt, set the real-time interrupt enable bit (RTIE) in RTCSC. RTIF is cleared by writing a 1 to RTIF. 15.4.1 RTC Operation Example This section shows an example of the RTC operation as the counter reaches a matching value from the modulo register. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 315 Chapter 15 Real-Time Counter (S08RTCV1) Internal 1-kHz Clock Source RTC Clock (RTCPS = 0xA) RTCCNT 0x52 0x53 0x54 0x55 0x00 0x01 RTIF RTCMOD 0x55 Figure 15-6. RTC Counter Overflow Example In the example of Figure 15-6, the selected clock source is the 1-kHz internal oscillator clock source. The prescaler (RTCPS) is set to 0xA or divide-by-4. The modulo value in the RTCMOD register is set to 0x55. When the counter, RTCCNT, reaches the modulo value of 0x55, the counter overflows to 0x00 and continues counting. The real-time interrupt flag, RTIF, sets when the counter value changes from 0x55 to 0x00. A real-time interrupt is generated when RTIF is set, if RTIE is set. 15.5 Initialization/Application Information This section provides example code to give some basic direction to a user on how to initialize and configure the RTC module. The example software is implemented in C language. The example below shows how to implement time of day with the RTC using the 1-kHz clock source to achieve the lowest possible power consumption. Because the 1-kHz clock source is not as accurate as a crystal, software can be added for any adjustments. For accuracy without adjustments at the expense of additional power consumption, the external clock (ERCLK) or the internal clock (IRCLK) can be selected with appropriate prescaler and modulo values. /* Initialize the elapsed time counters */ Seconds = 0; Minutes = 0; Hours = 0; Days=0; /* Configure RTC to interrupt every 1 second from 1-kHz clock source */ RTCMOD.byte = 0x00; RTCSC.byte = 0x1F; /********************************************************************** Function Name : RTC_ISR Notes : Interrupt service routine for RTC module. **********************************************************************/ MC9S08DZ60 Series Data Sheet, Rev. 4 316 Freescale Semiconductor Chapter 15 Real-Time Counter (S08RTCV1) #pragma TRAP_PROC void RTC_ISR(void) { /* Clear the interrupt flag */ RTCSC.byte = RTCSC.byte | 0x80; /* RTC interrupts every 1 Second */ Seconds++; /* 60 seconds in a minute */ if (Seconds > 59){ Minutes++; Seconds = 0; } /* 60 minutes in an hour */ if (Minutes > 59){ Hours++; Minutes = 0; } /* 24 hours in a day */ if (Hours > 23){ Days ++; Hours = 0; } MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 317 Chapter 15 Real-Time Counter (S08RTCV1) MC9S08DZ60 Series Data Sheet, Rev. 4 318 Freescale Semiconductor Chapter 16 Timer Pulse-Width Modulator (S08TPMV3) NOTE This chapter refers to S08TPM version 3, which applies to the 0M74K and newer mask sets of this device. 3M05C and older mask set devices use S08TPM version 2. If your device uses mask 3M05C or older, please refer to Appendix B, "Timer Pulse-Width Modulator (TPMV2) on page 391 for information pertaining to that module. 16.1 Introduction The TPM is a one-to-eight-channel timer system which supports traditional input capture, output compare, or edge-aligned PWM on each channel. A control bit allows the TPM to be configured such that all channels may be used for center-aligned PWM functions. Timing functions are based on a 16-bit counter with prescaler and modulo features to control frequency and range (period between overflows) of the time reference. This timing system is ideally suited for a wide range of control applications, and the center-aligned PWM capability extends the field of application to motor control in small appliances. The TPM uses one input/output (I/O) pin per channel, TPMxCHn, where x is the TPM number (for example, 1 or 2) and n is the channel number (for example, 0-5). The TPM shares its I/O pins with general-purpose I/O port pins (refer to the Pins and Connections chapter for more information). MC9S08DZ60 Series MCUs have two TPM modules. In all packages, TPM2 is 2-channel. The number of channels available on external pins in TPM1 depends on the package: * Six channels in 64-pin and 48-pin packages * Four channels in 32-pin packages. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 319 PORT A PTA7/PIA7/ADP7/IRQ PTA6/PIA6/ADP6 PTA5/PIA5/ADP5 PTA4/PIA4/ADP4 PTA3/PIA3/ADP3/ACMP1O PTA2/PIA2/ADP2/ACMP1PTA1/PIA1/ADP1/ACMP1+ PTA0/PIA0/ADP0/MCLK PORT B PTB7/PIB7/ADP15 PTB6/PIB6/ADP14 PTB5/PIB5/ADP13 PTB4/PIB4/ADP12 PTB3/PIB3/ADP11 PTB2/PIB2/ADP10 PTB1/PIB1/ADP9 PTB0/PIB0/ADP8 PORT C PTC7/ADP23 PTC6/ADP22 PTC5/ADP21 PTC4/ADP20 PTC3/ADP19 PTC2/ADP18 PTC1/ADP17 PTC0/ADP16 PORT D PTD7/PID7/TPM1CH5 PTD6/PID6/TPM1CH4 PTD5/PID5/TPM1CH3 PTD4/PID4/TPM1CH2 PTD3/PID3/TPM1CH1 PTD2/PID2/TPM1CH0 PTD1/PID1/TPM2CH1 PTD0/PID0/TPM2CH0 PORT E PTE7/RxD2/RXCAN PTE6/TxD2/TXCAN PTE5/SDA/MISO PTE4/SCL/MOSI PTE3/SPSCK PTE2/SS PTE1/RxD1 PTE0/TxD1 PORT F PTF7 PTF6/ACMP2O PTF5/ACMP2PTF4/ACMP2+ PTF3/TPM2CLK/SDA PTF2/TPM1CLK/SCL PTF1/RxD2 PTF0/TxD2 PORT G Chapter 16 Timer Pulse-Width Modulator (S08TPMV3) PTG5 PTG4 PTG3 PTG2 PTG1/XTAL PTG0/EXTAL HCS08 CORE CPU BKGD/MS BDC ANALOG COMPARATOR (ACMP1) BKP ACMP1O ACMP1ACMP1+ HCS08 SYSTEM CONTROL RESETS AND INTERRUPTS MODES OF OPERATION POWER MANAGEMENT COP LVD INT IRQ ADP7-ADP0 24-CHANNEL,12--BIT ANALOG-TO-DIGITAL CONVERTER (ADC) VREFH VREFL VDDA VSSA USER FLASH MC9S0DZ60 = 60K MC9S0DZ48 = 48K MC9S0DZ32 = 32K MC9S0DZ16 = 16K USER EEPROM MC9S0DZ60 = 2K TPM1CH5 TPM1CH0 6 TPM1CLK 2-CHANNEL TIMER/PWM MODULE (TPM2) TPM2CH1, TPM2CH0 TPM2CLK CONTROLLER AREA NETWORK (MSCAN) SERIAL PERIPHERAL INTERFACE MODULE (SPI) DEBUG MODULE (DBG) SERIAL COMMUNICATIONS INTERFACE (SCI1) VOLTAGE REGULATOR ADP15-ADP8 ADP23-ADP16 6-CHANNEL TIMER/PWM MODULE (TPM1) USER RAM MC9S0DZ60 = 4K REAL-TIME COUNTER (RTC) VDD VDD VSS VSS 8 IRQ RESET ANALOG COMPARATOR (ACMP2) IIC MODULE (IIC) SERIAL COMMUNICATIONS INTERFACE (SCI2) RxCAN TxCAN MISO MOSI SPSCK SS RxD1 TxD1 ACMP2O ACMP2ACMP2+ SDA SCL RxD2 TxD2 MULTI-PURPOSE CLOCK GENERATOR (MCG) XTAL EXTAL OSCILLATOR (XOSC) - VREFH/VREFL internally connected to VDDA/VSSA in 48-pin and 32-pin packages - VDD and VSS pins are each internally connected to two pads in 32-pin package - Pin not connected in 48-pin and 32-pin packages - Pin not connected in 32-pin package Figure 16-1. MC9S08DZ60 Block Diagram MC9S08DZ60 Series Data Sheet, Rev. 4 320 Freescale Semiconductor Chapter 16 Timer/PWM Module (S08TPMV3) 16.1.1 Features The TPM includes these distinctive features: * One to eight channels: -- Each channel may be input capture, output compare, or edge-aligned PWM -- Rising-Edge, falling-edge, or any-edge input capture trigger -- Set, clear, or toggle output compare action -- Selectable polarity on PWM outputs * Module may be configured for buffered, center-aligned pulse-width-modulation (CPWM) on all channels * Timer clock source selectable as prescaled bus clock, fixed system clock, or an external clock pin -- Prescale taps for divide-by 1, 2, 4, 8, 16, 32, 64, or 128 -- Fixed system clock source are synchronized to the bus clock by an on-chip synchronization circuit -- External clock pin may be shared with any timer channel pin or a separated input pin * 16-bit free-running or modulo up/down count operation * Timer system enable * One interrupt per channel plus terminal count interrupt 16.1.2 Modes of Operation In general, TPM channels may be independently configured to operate in input capture, output compare, or edge-aligned PWM modes. A control bit allows the whole TPM (all channels) to switch to center-aligned PWM mode. When center-aligned PWM mode is selected, input capture, output compare, and edge-aligned PWM functions are not available on any channels of this TPM module. When the microcontroller is in active BDM background or BDM foreground mode, the TPM temporarily suspends all counting until the microcontroller returns to normal user operating mode. During stop mode, all system clocks, including the main oscillator, are stopped; therefore, the TPM is effectively disabled until clocks resume. During wait mode, the TPM continues to operate normally. Provided the TPM does not need to produce a real time reference or provide the interrupt source(s) needed to wake the MCU from wait mode, the user can save power by disabling TPM functions before entering wait mode. * Input capture mode When a selected edge event occurs on the associated MCU pin, the current value of the 16-bit timer counter is captured into the channel value register and an interrupt flag bit is set. Rising edges, falling edges, any edge, or no edge (disable channel) may be selected as the active edge which triggers the input capture. * Output compare mode When the value in the timer counter register matches the channel value register, an interrupt flag bit is set, and a selected output action is forced on the associated MCU pin. The output compare action may be selected to force the pin to zero, force the pin to one, toggle the pin, or ignore the pin (used for software timing functions). MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 321 Chapter 16 Timer/PWM Module (S08TPMV3) * * Edge-aligned PWM mode The value of a 16-bit modulo register plus 1 sets the period of the PWM output signal. The channel value register sets the duty cycle of the PWM output signal. The user may also choose the polarity of the PWM output signal. Interrupts are available at the end of the period and at the duty-cycle transition point. This type of PWM signal is called edge-aligned because the leading edges of all PWM signals are aligned with the beginning of the period, which is the same for all channels within a TPM. Center-aligned PWM mode Twice the value of a 16-bit modulo register sets the period of the PWM output, and the channel-value register sets the half-duty-cycle duration. The timer counter counts up until it reaches the modulo value and then counts down until it reaches zero. As the count matches the channel value register while counting down, the PWM output becomes active. When the count matches the channel value register while counting up, the PWM output becomes inactive. This type of PWM signal is called center-aligned because the centers of the active duty cycle periods for all channels are aligned with a count value of zero. This type of PWM is required for types of motors used in small appliances. This is a high-level description only. Detailed descriptions of operating modes are in later sections. 16.1.3 Block Diagram The TPM uses one input/output (I/O) pin per channel, TPMxCHn (timer channel n) where n is the channel number (1-8). The TPM shares its I/O pins with general purpose I/O port pins (refer to I/O pin descriptions in full-chip specification for the specific chip implementation). Figure 16-2 shows the TPM structure. The central component of the TPM is the 16-bit counter that can operate as a free-running counter or a modulo up/down counter. The TPM counter (when operating in normal up-counting mode) provides the timing reference for the input capture, output compare, and edge-aligned PWM functions. The timer counter modulo registers, TPMxMODH:TPMxMODL, control the modulo value of the counter (the values 0x0000 or 0xFFFF effectively make the counter free running). Software can read the counter value at any time without affecting the counting sequence. Any write to either half of the TPMxCNT counter resets the counter, regardless of the data value written. MC9S08DZ60 Series Data Sheet, Rev. 4 322 Freescale Semiconductor Chapter 16 Timer/PWM Module (S08TPMV3) BUS CLOCK FIXED SYSTEM CLOCK SYNC EXTERNAL CLOCK CLOCK SOURCE SELECT OFF, BUS, FIXED SYSTEM CLOCK, EXT PRESCALE AND SELECT 1, 2, 4, 8, 16, 32, 64, or 128 CLKSB:CLKSA PS2:PS1:PS0 CPWMS 16-BIT COUNTER TOF COUNTER RESET TOIE INTERRUPT LOGIC 16-BIT COMPARATOR TPMxMODH:TPMxMODL CHANNEL 0 ELS0B ELS0A PORT LOGIC TPMxCH0 16-BIT COMPARATOR TPMxC0VH:TPMxC0VL CH0F INTERNAL BUS 16-BIT LATCH CHANNEL 1 MS0B MS0A ELS1B ELS1A CH0IE INTERRUPT LOGIC PORT LOGIC TPMxCH1 16-BIT COMPARATOR TPMxC1VH:TPMxC1VL CH1F 16-BIT LATCH MS1B CH1IE MS1A INTERRUPT LOGIC Up to 8 channels CHANNEL 7 ELS7B ELS7A PORT LOGIC TPMxCH7 16-BIT COMPARATOR TPMxC7VH:TPMxC7VL CH7F 16-BIT LATCH MS7B MS7A CH7IE INTERRUPT LOGIC Figure 16-2. TPM Block Diagram MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 323 Chapter 16 Timer/PWM Module (S08TPMV3) The TPM channels are programmable independently as input capture, output compare, or edge-aligned PWM channels. Alternately, the TPM can be configured to produce CPWM outputs on all channels. When the TPM is configured for CPWMs, the counter operates as an up/down counter; input capture, output compare, and EPWM functions are not practical. If a channel is configured as input capture, an internal pullup device may be enabled for that channel. The details of how a module interacts with pin controls depends upon the chip implementation because the I/O pins and associated general purpose I/O controls are not part of the module. Refer to the discussion of the I/O port logic in a full-chip specification. Because center-aligned PWMs are usually used to drive 3-phase AC-induction motors and brushless DC motors, they are typically used in sets of three or six channels. 16.2 Signal Description Table 16-1 shows the user-accessible signals for the TPM. The number of channels may be varied from one to eight. When an external clock is included, it can be shared with the same pin as any TPM channel; however, it could be connected to a separate input pin. Refer to the I/O pin descriptions in full-chip specification for the specific chip implementation. Table 16-1. Signal Properties Name Function EXTCLK1 2 TPMxCHn External clock source which may be selected to drive the TPM counter. I/O pin associated with TPM channel n 1 When preset, this signal can share any channel pin; however depending upon full-chip implementation, this signal could be connected to a separate external pin. 2 n=channel number (1 to 8) Refer to documentation for the full-chip for details about reset states, port connections, and whether there is any pullup device on these pins. TPM channel pins can be associated with general purpose I/O pins and have passive pullup devices which can be enabled with a control bit when the TPM or general purpose I/O controls have configured the associated pin as an input. When no TPM function is enabled to use a corresponding pin, the pin reverts to being controlled by general purpose I/O controls, including the port-data and data-direction registers. Immediately after reset, no TPM functions are enabled, so all associated pins revert to general purpose I/O control. 16.2.1 Detailed Signal Descriptions This section describes each user-accessible pin signal in detail. Although Table 16-1 grouped all channel pins together, any TPM pin can be shared with the external clock source signal. Since I/O pin logic is not part of the TPM, refer to full-chip documentation for a specific derivative for more details about the interaction of TPM pin functions and general purpose I/O controls including port data, data direction, and pullup controls. MC9S08DZ60 Series Data Sheet, Rev. 4 324 Freescale Semiconductor Chapter 16 Timer/PWM Module (S08TPMV3) 16.2.1.1 EXTCLK -- External Clock Source Control bits in the timer status and control register allow the user to select nothing (timer disable), the bus-rate clock (the normal default source), a crystal-related clock, or an external clock as the clock which drives the TPM prescaler and subsequently the 16-bit TPM counter. The external clock source is synchronized in the TPM. The bus clock clocks the synchronizer; the frequency of the external source must be no more than one-fourth the frequency of the bus-rate clock, to meet Nyquist criteria and allowing for jitter. The external clock signal shares the same pin as a channel I/O pin, so the channel pin will not be usable for channel I/O function when selected as the external clock source. It is the user's responsibility to avoid such settings. If this pin is used as an external clock source (CLKSB:CLKSA = 1:1), the channel can still be used in output compare mode as a software timer (ELSnB:ELSnA = 0:0). 16.2.1.2 TPMxCHn -- TPM Channel n I/O Pin(s) Each TPM channel is associated with an I/O pin on the MCU. The function of this pin depends on the channel configuration. The TPM pins share with general purpose I/O pins, where each pin has a port data register bit, and a data direction control bit, and the port has optional passive pullups which may be enabled whenever a port pin is acting as an input. The TPM channel does not control the I/O pin when (ELSnB:ELSnA = 0:0) or when (CLKSB:CLKSA = 0:0) so it normally reverts to general purpose I/O control. When CPWMS = 1 (and ELSnB:ELSnA not = 0:0), all channels within the TPM are configured for center-aligned PWM and the TPMxCHn pins are all controlled by the TPM system. When CPWMS=0, the MSnB:MSnA control bits determine whether the channel is configured for input capture, output compare, or edge-aligned PWM. When a channel is configured for input capture (CPWMS=0, MSnB:MSnA = 0:0 and ELSnB:ELSnA not = 0:0), the TPMxCHn pin is forced to act as an edge-sensitive input to the TPM. ELSnB:ELSnA control bits determine what polarity edge or edges will trigger input-capture events. A synchronizer based on the bus clock is used to synchronize input edges to the bus clock. This implies the minimum pulse width--that can be reliably detected--on an input capture pin is four bus clock periods (with ideal clock pulses as near as two bus clocks can be detected). TPM uses this pin as an input capture input to override the port data and data direction controls for the same pin. When a channel is configured for output compare (CPWMS=0, MSnB:MSnA = 0:1 and ELSnB:ELSnA not = 0:0), the associated data direction control is overridden, the TPMxCHn pin is considered an output controlled by the TPM, and the ELSnB:ELSnA control bits determine how the pin is controlled. The remaining three combinations of ELSnB:ELSnA determine whether the TPMxCHn pin is toggled, cleared, or set each time the 16-bit channel value register matches the timer counter. When the output compare toggle mode is initially selected, the previous value on the pin is driven out until the next output compare event--then the pin is toggled. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 325 Chapter 16 Timer/PWM Module (S08TPMV3) When a channel is configured for edge-aligned PWM (CPWMS=0, MSnB=1 and ELSnB:ELSnA not = 0:0), the data direction is overridden, the TPMxCHn pin is forced to be an output controlled by the TPM, and ELSnA controls the polarity of the PWM output signal on the pin. When ELSnB:ELSnA=1:0, the TPMxCHn pin is forced high at the start of each new period (TPMxCNT=0x0000), and the pin is forced low when the channel value register matches the timer counter. When ELSnA=1, the TPMxCHn pin is forced low at the start of each new period (TPMxCNT=0x0000), and the pin is forced high when the channel value register matches the timer counter. TPMxMODH:TPMxMODL = 0x0008 TPMxCnVH:TPMxCnVL = 0x0005 TPMxCNTH:TPMxCNTL ... 0 1 2 3 4 5 6 7 8 0 1 2 ... 2 ... TPMxCHn CHnF BIT TOF BIT Figure 16-3. High-True Pulse of an Edge-Aligned PWM TPMxMODH:TPMxMODL = 0x0008 TPMxCnVH:TPMxCnVL = 0x0005 TPMxCNTH:TPMxCNTL ... 0 1 2 3 4 5 6 7 8 0 1 TPMxCHn CHnF BIT TOF BIT Figure 16-4. Low-True Pulse of an Edge-Aligned PWM MC9S08DZ60 Series Data Sheet, Rev. 4 326 Freescale Semiconductor Chapter 16 Timer/PWM Module (S08TPMV3) When the TPM is configured for center-aligned PWM (and ELSnB:ELSnA not = 0:0), the data direction for all channels in this TPM are overridden, the TPMxCHn pins are forced to be outputs controlled by the TPM, and the ELSnA bits control the polarity of each TPMxCHn output. If ELSnB:ELSnA=1:0, the corresponding TPMxCHn pin is cleared when the timer counter is counting up, and the channel value register matches the timer counter; the TPMxCHn pin is set when the timer counter is counting down, and the channel value register matches the timer counter. If ELSnA=1, the corresponding TPMxCHn pin is set when the timer counter is counting up and the channel value register matches the timer counter; the TPMxCHn pin is cleared when the timer counter is counting down and the channel value register matches the timer counter. TPMxMODH:TPMxMODL = 0x0008 TPMxCnVH:TPMxCnVL = 0x0005 TPMxCNTH:TPMxCNTL ... 7 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 7 6 5 ... 7 8 7 6 5 ... TPMxCHn CHnF BIT TOF BIT Figure 16-5. High-True Pulse of a Center-Aligned PWM TPMxMODH:TPMxMODL = 0x0008 TPMxCnVH:TPMxCnVL = 0x0005 TPMxCNTH:TPMxCNTL ... 7 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 TPMxCHn CHnF BIT TOF BIT Figure 16-6. Low-True Pulse of a Center-Aligned PWM MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 327 Chapter 16 Timer/PWM Module (S08TPMV3) 16.3 Register Definition This section consists of register descriptions in address order. A typical MCU system may contain multiple TPMs, and each TPM may have one to eight channels, so register names include placeholder characters to identify which TPM and which channel is being referenced. For example, TPMxCnSC refers to timer (TPM) x, channel n. TPM1C2SC would be the status and control register for channel 2 of timer 1. 16.3.1 TPM Status and Control Register (TPMxSC) TPMxSC contains the overflow status flag and control bits used to configure the interrupt enable, TPM configuration, clock source, and prescale factor. These controls relate to all channels within this timer module. 7 R TOF W 0 Reset 0 6 5 4 3 2 1 0 TOIE CPWMS CLKSB CLKSA PS2 PS1 PS0 0 0 0 0 0 0 0 Figure 16-7. TPM Status and Control Register (TPMxSC) Table 16-2. TPMxSC Field Descriptions Field Description 7 TOF Timer overflow flag. This read/write flag is set when the TPM counter resets to 0x0000 after reaching the modulo value programmed in the TPM counter modulo registers. Clear TOF by reading the TPM status and control register when TOF is set and then writing a logic 0 to TOF. If another TPM overflow occurs before the clearing sequence is complete, the sequence is reset so TOF would remain set after the clear sequence was completed for the earlier TOF. This is done so a TOF interrupt request cannot be lost during the clearing sequence for a previous TOF. Reset clears TOF. Writing a logic 1 to TOF has no effect. 0 TPM counter has not reached modulo value or overflow 1 TPM counter has overflowed 6 TOIE Timer overflow interrupt enable. This read/write bit enables TPM overflow interrupts. If TOIE is set, an interrupt is generated when TOF equals one. Reset clears TOIE. 0 TOF interrupts inhibited (use for software polling) 1 TOF interrupts enabled 5 CPWMS Center-aligned PWM select. When present, this read/write bit selects CPWM operating mode. By default, the TPM operates in up-counting mode for input capture, output compare, and edge-aligned PWM functions. Setting CPWMS reconfigures the TPM to operate in up/down counting mode for CPWM functions. Reset clears CPWMS. 0 All channels operate as input capture, output compare, or edge-aligned PWM mode as selected by the MSnB:MSnA control bits in each channel's status and control register. 1 All channels operate in center-aligned PWM mode. MC9S08DZ60 Series Data Sheet, Rev. 4 328 Freescale Semiconductor Chapter 16 Timer/PWM Module (S08TPMV3) Table 16-2. TPMxSC Field Descriptions (continued) Field Description 4-3 Clock source selects. As shown in Table 16-3, this 2-bit field is used to disable the TPM system or select one of CLKS[B:A] three clock sources to drive the counter prescaler. The fixed system clock source is only meaningful in systems with a PLL-based or FLL-based system clock. When there is no PLL or FLL, the fixed-system clock source is the same as the bus rate clock. The external source is synchronized to the bus clock by TPM module, and the fixed system clock source (when a PLL or FLL is present) is synchronized to the bus clock by an on-chip synchronization circuit. When a PLL or FLL is present but not enabled, the fixed-system clock source is the same as the bus-rate clock. 2-0 PS[2:0] Prescale factor select. This 3-bit field selects one of 8 division factors for the TPM clock input as shown in Table 16-4. This prescaler is located after any clock source synchronization or clock source selection so it affects the clock source selected to drive the TPM system. The new prescale factor will affect the clock source on the next system clock cycle after the new value is updated into the register bits. Table 16-3. TPM-Clock-Source Selection CLKSB:CLKSA TPM Clock Source to Prescaler Input 00 No clock selected (TPM counter disable) 01 Bus rate clock 10 Fixed system clock 11 External source Table 16-4. Prescale Factor Selection 16.3.2 PS2:PS1:PS0 TPM Clock Source Divided-by 000 1 001 2 010 4 011 8 100 16 101 32 110 64 111 128 TPM-Counter Registers (TPMxCNTH:TPMxCNTL) The two read-only TPM counter registers contain the high and low bytes of the value in the TPM counter. Reading either byte (TPMxCNTH or TPMxCNTL) latches the contents of both bytes into a buffer where they remain latched until the other half is read. This allows coherent 16-bit reads in either big-endian or little-endian order which makes this more friendly to various compiler implementations. The coherency mechanism is automatically restarted by an MCU reset or any write to the timer status/control register (TPMxSC). MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 329 Chapter 16 Timer/PWM Module (S08TPMV3) Reset clears the TPM counter registers. Writing any value to TPMxCNTH or TPMxCNTL also clears the TPM counter (TPMxCNTH:TPMxCNTL) and resets the coherency mechanism, regardless of the data involved in the write. R 7 6 5 4 3 2 1 0 Bit 15 14 13 12 11 10 9 Bit 8 0 0 W Reset Any write to TPMxCNTH clears the 16-bit counter 0 0 0 0 0 0 Figure 16-8. TPM Counter Register High (TPMxCNTH) R 7 6 5 4 3 2 1 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 W Reset Any write to TPMxCNTL clears the 16-bit counter 0 0 0 0 0 0 Figure 16-9. TPM Counter Register Low (TPMxCNTL) When BDM is active, the timer counter is frozen (this is the value that will be read by user); the coherency mechanism is frozen such that the buffer latches remain in the state they were in when the BDM became active, even if one or both counter halves are read while BDM is active. This assures that if the user was in the middle of reading a 16-bit register when BDM became active, it will read the appropriate value from the other half of the 16-bit value after returning to normal execution. In BDM mode, writing any value to TPMxSC, TPMxCNTH or TPMxCNTL registers resets the read coherency mechanism of the TPMxCNTH:L registers, regardless of the data involved in the write. 16.3.3 TPM Counter Modulo Registers (TPMxMODH:TPMxMODL) The read/write TPM modulo registers contain the modulo value for the TPM counter. After the TPM counter reaches the modulo value, the TPM counter resumes counting from 0x0000 at the next clock, and the overflow flag (TOF) becomes set. Writing to TPMxMODH or TPMxMODL inhibits the TOF bit and overflow interrupts until the other byte is written. Reset sets the TPM counter modulo registers to 0x0000 which results in a free running timer counter (modulo disabled). Writing to either byte (TPMxMODH or TPMxMODL) latches the value into a buffer and the registers are updated with the value of their write buffer according to the value of CLKSB:CLKSA bits, so: * If (CLKSB:CLKSA = 0:0), then the registers are updated when the second byte is written * If (CLKSB:CLKSA not = 0:0), then the registers are updated after both bytes were written, and the TPM counter changes from (TPMxMODH:TPMxMODL - 1) to (TPMxMODH:TPMxMODL). If the TPM counter is a free-running counter, the update is made when the TPM counter changes from 0xFFFE to 0xFFFF The latching mechanism may be manually reset by writing to the TPMxSC address (whether BDM is active or not). MC9S08DZ60 Series Data Sheet, Rev. 4 330 Freescale Semiconductor Chapter 16 Timer/PWM Module (S08TPMV3) When BDM is active, the coherency mechanism is frozen (unless reset by writing to TPMxSC register) such that the buffer latches remain in the state they were in when the BDM became active, even if one or both halves of the modulo register are written while BDM is active. Any write to the modulo registers bypasses the buffer latches and directly writes to the modulo register while BDM is active. 7 6 5 4 3 2 1 0 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 R W Reset Figure 16-10. TPM Counter Modulo Register High (TPMxMODH) 7 6 5 4 3 2 1 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 R W Reset Figure 16-11. TPM Counter Modulo Register Low (TPMxMODL) Reset the TPM counter before writing to the TPM modulo registers to avoid confusion about when the first counter overflow will occur. 16.3.4 TPM Channel n Status and Control Register (TPMxCnSC) TPMxCnSC contains the channel-interrupt-status flag and control bits used to configure the interrupt enable, channel configuration, and pin function. 7 R 6 5 4 3 2 CHnIE MSnB MSnA ELSnB ELSnA 0 0 0 0 0 CHnF W 0 Reset 0 1 0 0 0 0 0 = Unimplemented or Reserved Figure 16-12. TPM Channel n Status and Control Register (TPMxCnSC) MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 331 Chapter 16 Timer/PWM Module (S08TPMV3) Table 16-5. TPMxCnSC Field Descriptions Field Description 7 CHnF Channel n flag. When channel n is an input-capture channel, this read/write bit is set when an active edge occurs on the channel n pin. When channel n is an output compare or edge-aligned/center-aligned PWM channel, CHnF is set when the value in the TPM counter registers matches the value in the TPM channel n value registers. When channel n is an edge-aligned/center-aligned PWM channel and the duty cycle is set to 0% or 100%, CHnF will not be set even when the value in the TPM counter registers matches the value in the TPM channel n value registers. A corresponding interrupt is requested when CHnF is set and interrupts are enabled (CHnIE = 1). Clear CHnF by reading TPMxCnSC while CHnF is set and then writing a logic 0 to CHnF. If another interrupt request occurs before the clearing sequence is complete, the sequence is reset so CHnF remains set after the clear sequence completed for the earlier CHnF. This is done so a CHnF interrupt request cannot be lost due to clearing a previous CHnF. Reset clears the CHnF bit. Writing a logic 1 to CHnF has no effect. 0 No input capture or output compare event occurred on channel n 1 Input capture or output compare event on channel n 6 CHnIE Channel n interrupt enable. This read/write bit enables interrupts from channel n. Reset clears CHnIE. 0 Channel n interrupt requests disabled (use for software polling) 1 Channel n interrupt requests enabled 5 MSnB Mode select B for TPM channel n. When CPWMS=0, MSnB=1 configures TPM channel n for edge-aligned PWM mode. Refer to the summary of channel mode and setup controls in Table 16-6. 4 MSnA Mode select A for TPM channel n. When CPWMS=0 and MSnB=0, MSnA configures TPM channel n for input-capture mode or output compare mode. Refer to Table 16-6 for a summary of channel mode and setup controls. Note: If the associated port pin is not stable for at least two bus clock cycles before changing to input capture mode, it is possible to get an unexpected indication of an edge trigger. 3-2 ELSnB ELSnA Edge/level select bits. Depending upon the operating mode for the timer channel as set by CPWMS:MSnB:MSnA and shown in Table 16-6, these bits select the polarity of the input edge that triggers an input capture event, select the level that will be driven in response to an output compare match, or select the polarity of the PWM output. Setting ELSnB:ELSnA to 0:0 configures the related timer pin as a general purpose I/O pin not related to any timer functions. This function is typically used to temporarily disable an input capture channel or to make the timer pin available as a general purpose I/O pin when the associated timer channel is set up as a software timer that does not require the use of a pin. Table 16-6. Mode, Edge, and Level Selection CPWMS MSnB:MSnA ELSnB:ELSnA X XX 00 Mode Configuration Pin not used for TPM - revert to general purpose I/O or other peripheral control MC9S08DZ60 Series Data Sheet, Rev. 4 332 Freescale Semiconductor Chapter 16 Timer/PWM Module (S08TPMV3) Table 16-6. Mode, Edge, and Level Selection CPWMS MSnB:MSnA ELSnB:ELSnA Mode Configuration 0 00 01 Input capture Capture on rising edge only 01 10 Capture on falling edge only 11 Capture on rising or falling edge 01 1X Output compare 10 Clear output on compare 11 Set output on compare 10 Edge-aligned PWM X1 1 XX High-true pulses (clear output on compare) Low-true pulses (set output on compare) 10 Center-aligned PWM X1 16.3.5 Toggle output on compare High-true pulses (clear output on compare-up) Low-true pulses (set output on compare-up) TPM Channel Value Registers (TPMxCnVH:TPMxCnVL) These read/write registers contain the captured TPM counter value of the input capture function or the output compare value for the output compare or PWM functions. The channel registers are cleared by reset. 7 6 5 4 3 2 1 0 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 R W Reset Figure 16-13. TPM Channel Value Register High (TPMxCnVH) 7 6 5 4 3 2 1 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 R W Reset Figure 16-14. TPM Channel Value Register Low (TPMxCnVL) In input capture mode, reading either byte (TPMxCnVH or TPMxCnVL) latches the contents of both bytes into a buffer where they remain latched until the other half is read. This latching mechanism also resets MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 333 Chapter 16 Timer/PWM Module (S08TPMV3) (becomes unlatched) when the TPMxCnSC register is written (whether BDM mode is active or not). Any write to the channel registers will be ignored during the input capture mode. When BDM is active, the coherency mechanism is frozen (unless reset by writing to TPMxCnSC register) such that the buffer latches remain in the state they were in when the BDM became active, even if one or both halves of the channel register are read while BDM is active. This assures that if the user was in the middle of reading a 16-bit register when BDM became active, it will read the appropriate value from the other half of the 16-bit value after returning to normal execution. The value read from the TPMxCnVH and TPMxCnVL registers in BDM mode is the value of these registers and not the value of their read buffer. In output compare or PWM modes, writing to either byte (TPMxCnVH or TPMxCnVL) latches the value into a buffer. After both bytes are written, they are transferred as a coherent 16-bit value into the timer-channel registers according to the value of CLKSB:CLKSA bits and the selected mode, so: * If (CLKSB:CLKSA = 0:0), then the registers are updated when the second byte is written. * If (CLKSB:CLKSA not = 0:0 and in output compare mode) then the registers are updated after the second byte is written and on the next change of the TPM counter (end of the prescaler counting). * If (CLKSB:CLKSA not = 0:0 and in EPWM or CPWM modes), then the registers are updated after the both bytes were written, and the TPM counter changes from (TPMxMODH:TPMxMODL - 1) to (TPMxMODH:TPMxMODL). If the TPM counter is a free-running counter then the update is made when the TPM counter changes from 0xFFFE to 0xFFFF. The latching mechanism may be manually reset by writing to the TPMxCnSC register (whether BDM mode is active or not). This latching mechanism allows coherent 16-bit writes in either big-endian or little-endian order which is friendly to various compiler implementations. When BDM is active, the coherency mechanism is frozen such that the buffer latches remain in the state they were in when the BDM became active even if one or both halves of the channel register are written while BDM is active. Any write to the channel registers bypasses the buffer latches and directly write to the channel register while BDM is active. The values written to the channel register while BDM is active are used for PWM & output compare operation once normal execution resumes. Writes to the channel registers while BDM is active do not interfere with partial completion of a coherency sequence. After the coherency mechanism has been fully exercised, the channel registers are updated using the buffered values written (while BDM was not active) by the user. 16.4 Functional Description All TPM functions are associated with a central 16-bit counter which allows flexible selection of the clock source and prescale factor. There is also a 16-bit modulo register associated with the main counter. The CPWMS control bit chooses between center-aligned PWM operation for all channels in the TPM (CPWMS=1) or general purpose timing functions (CPWMS=0) where each channel can independently be configured to operate in input capture, output compare, or edge-aligned PWM mode. The CPWMS control bit is located in the main TPM status and control register because it affects all channels within the TPM and influences the way the main counter operates. (In CPWM mode, the counter changes to an up/down mode rather than the up-counting mode used for general purpose timer functions.) MC9S08DZ60 Series Data Sheet, Rev. 4 334 Freescale Semiconductor Chapter 16 Timer/PWM Module (S08TPMV3) The following sections describe the main counter and each of the timer operating modes (input capture, output compare, edge-aligned PWM, and center-aligned PWM). Because details of pin operation and interrupt activity depend upon the operating mode, these topics will be covered in the associated mode explanation sections. 16.4.1 Counter All timer functions are based on the main 16-bit counter (TPMxCNTH:TPMxCNTL). This section discusses selection of the clock source, end-of-count overflow, up-counting vs. up/down counting, and manual counter reset. 16.4.1.1 Counter Clock Source The 2-bit field, CLKSB:CLKSA, in the timer status and control register (TPMxSC) selects one of three possible clock sources or OFF (which effectively disables the TPM). See Table 16-3. After any MCU reset, CLKSB:CLKSA=0:0 so no clock source is selected, and the TPM is in a very low power state. These control bits may be read or written at any time and disabling the timer (writing 00 to the CLKSB:CLKSA field) does not affect the values in the counter or other timer registers. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 335 Chapter 16 Timer/PWM Module (S08TPMV3) Table 16-7. TPM Clock Source Selection CLKSB:CLKSA TPM Clock Source to Prescaler Input 00 No clock selected (TPM counter disabled) 01 Bus rate clock 10 Fixed system clock 11 External source The bus rate clock is the main system bus clock for the MCU. This clock source requires no synchronization because it is the clock that is used for all internal MCU activities including operation of the CPU and buses. In MCUs that have no PLL and FLL or the PLL and FLL are not engaged, the fixed system clock source is the same as the bus-rate-clock source, and it does not go through a synchronizer. When a PLL or FLL is present and engaged, a synchronizer is required between the crystal divided-by two clock source and the timer counter so counter transitions will be properly aligned to bus-clock transitions. A synchronizer will be used at chip level to synchronize the crystal-related source clock to the bus clock. The external clock source may be connected to any TPM channel pin. This clock source always has to pass through a synchronizer to assure that counter transitions are properly aligned to bus clock transitions. The bus-rate clock drives the synchronizer; therefore, to meet Nyquist criteria even with jitter, the frequency of the external clock source must not be faster than the bus rate divided-by four. With ideal clocks the external clock can be as fast as bus clock divided by four. When the external clock source shares the TPM channel pin, this pin should not be used for other channel timing functions. For example, it would be ambiguous to configure channel 0 for input capture when the TPM channel 0 pin was also being used as the timer external clock source. (It is the user's responsibility to avoid such settings.) The TPM channel could still be used in output compare mode for software timing functions (pin controls set not to affect the TPM channel pin). 16.4.1.2 Counter Overflow and Modulo Reset An interrupt flag and enable are associated with the 16-bit main counter. The flag (TOF) is a software-accessible indication that the timer counter has overflowed. The enable signal selects between software polling (TOIE=0) where no hardware interrupt is generated, or interrupt-driven operation (TOIE=1) where a static hardware interrupt is generated whenever the TOF flag is equal to one. The conditions causing TOF to become set depend on whether the TPM is configured for center-aligned PWM (CPWMS=1). In the simplest mode, there is no modulus limit and the TPM is not in CPWMS=1 mode. In this case, the 16-bit timer counter counts from 0x0000 through 0xFFFF and overflows to 0x0000 on the next counting clock. TOF becomes set at the transition from 0xFFFF to 0x0000. When a modulus limit is set, TOF becomes set at the transition from the value set in the modulus register to 0x0000. When the TPM is in center-aligned PWM mode (CPWMS=1), the TOF flag gets set as the counter changes direction at the end of the count value set in the modulus register (that is, at the transition from the value set in the modulus register to the next lower count value). This corresponds to the end of a PWM period (the 0x0000 count value corresponds to the center of a period). MC9S08DZ60 Series Data Sheet, Rev. 4 336 Freescale Semiconductor Chapter 16 Timer/PWM Module (S08TPMV3) 16.4.1.3 Counting Modes The main timer counter has two counting modes. When center-aligned PWM is selected (CPWMS=1), the counter operates in up/down counting mode. Otherwise, the counter operates as a simple up counter. As an up counter, the timer counter counts from 0x0000 through its terminal count and then continues with 0x0000. The terminal count is 0xFFFF or a modulus value in TPMxMODH:TPMxMODL. When center-aligned PWM operation is specified, the counter counts up from 0x0000 through its terminal count and then down to 0x0000 where it changes back to up counting. Both 0x0000 and the terminal count value are normal length counts (one timer clock period long). In this mode, the timer overflow flag (TOF) becomes set at the end of the terminal-count period (as the count changes to the next lower count value). 16.4.1.4 Manual Counter Reset The main timer counter can be manually reset at any time by writing any value to either half of TPMxCNTH or TPMxCNTL. Resetting the counter in this manner also resets the coherency mechanism in case only half of the counter was read before resetting the count. 16.4.2 Channel Mode Selection Provided CPWMS=0, the MSnB and MSnA control bits in the channel n status and control registers determine the basic mode of operation for the corresponding channel. Choices include input capture, output compare, and edge-aligned PWM. 16.4.2.1 Input Capture Mode With the input-capture function, the TPM can capture the time at which an external event occurs. When an active edge occurs on the pin of an input-capture channel, the TPM latches the contents of the TPM counter into the channel-value registers (TPMxCnVH:TPMxCnVL). Rising edges, falling edges, or any edge may be chosen as the active edge that triggers an input capture. In input capture mode, the TPMxCnVH and TPMxCnVL registers are read only. When either half of the 16-bit capture register is read, the other half is latched into a buffer to support coherent 16-bit accesses in big-endian or little-endian order. The coherency sequence can be manually reset by writing to the channel status/control register (TPMxCnSC). An input capture event sets a flag bit (CHnF) which may optionally generate a CPU interrupt request. While in BDM, the input capture function works as configured by the user. When an external event occurs, the TPM latches the contents of the TPM counter (which is frozen because of the BDM mode) into the channel value registers and sets the flag bit. 16.4.2.2 Output Compare Mode With the output-compare function, the TPM can generate timed pulses with programmable position, polarity, duration, and frequency. When the counter reaches the value in the channel-value registers of an output-compare channel, the TPM can set, clear, or toggle the channel pin. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 337 Chapter 16 Timer/PWM Module (S08TPMV3) In output compare mode, values are transferred to the corresponding timer channel registers only after both 8-bit halves of a 16-bit register have been written and according to the value of CLKSB:CLKSA bits, so: * If (CLKSB:CLKSA = 0:0), the registers are updated when the second byte is written * If (CLKSB:CLKSA not = 0:0), the registers are updated at the next change of the TPM counter (end of the prescaler counting) after the second byte is written. The coherency sequence can be manually reset by writing to the channel status/control register (TPMxCnSC). An output compare event sets a flag bit (CHnF) which may optionally generate a CPU-interrupt request. 16.4.2.3 Edge-Aligned PWM Mode This type of PWM output uses the normal up-counting mode of the timer counter (CPWMS=0) and can be used when other channels in the same TPM are configured for input capture or output compare functions. The period of this PWM signal is determined by the value of the modulus register (TPMxMODH:TPMxMODL) plus 1. The duty cycle is determined by the setting in the timer channel register (TPMxCnVH:TPMxCnVL). The polarity of this PWM signal is determined by the setting in the ELSnA control bit. 0% and 100% duty cycle cases are possible. The output compare value in the TPM channel registers determines the pulse width (duty cycle) of the PWM signal (Figure 16-15). The time between the modulus overflow and the output compare is the pulse width. If ELSnA=0, the counter overflow forces the PWM signal high, and the output compare forces the PWM signal low. If ELSnA=1, the counter overflow forces the PWM signal low, and the output compare forces the PWM signal high. OVERFLOW OVERFLOW OVERFLOW PERIOD PULSE WIDTH TPMxCHn OUTPUT COMPARE OUTPUT COMPARE OUTPUT COMPARE Figure 16-15. PWM Period and Pulse Width (ELSnA=0) When the channel value register is set to 0x0000, the duty cycle is 0%. 100% duty cycle can be achieved by setting the timer-channel register (TPMxCnVH:TPMxCnVL) to a value greater than the modulus setting. This implies that the modulus setting must be less than 0xFFFF in order to get 100% duty cycle. Because the TPM may be used in an 8-bit MCU, the settings in the timer channel registers are buffered to ensure coherent 16-bit updates and to avoid unexpected PWM pulse widths. Writes to any of the registers TPMxCnVH and TPMxCnVL, actually write to buffer registers. In edge-aligned PWM mode, values are transferred to the corresponding timer-channel registers according to the value of CLKSB:CLKSA bits, so: * If (CLKSB:CLKSA = 0:0), the registers are updated when the second byte is written * If (CLKSB:CLKSA not = 0:0), the registers are updated after the both bytes were written, and the TPM counter changes from (TPMxMODH:TPMxMODL - 1) to (TPMxMODH:TPMxMODL). If MC9S08DZ60 Series Data Sheet, Rev. 4 338 Freescale Semiconductor Chapter 16 Timer/PWM Module (S08TPMV3) the TPM counter is a free-running counter then the update is made when the TPM counter changes from 0xFFFE to 0xFFFF. 16.4.2.4 Center-Aligned PWM Mode This type of PWM output uses the up/down counting mode of the timer counter (CPWMS=1). The output compare value in TPMxCnVH:TPMxCnVL determines the pulse width (duty cycle) of the PWM signal while the period is determined by the value in TPMxMODH:TPMxMODL. TPMxMODH:TPMxMODL should be kept in the range of 0x0001 to 0x7FFF because values outside this range can produce ambiguous results. ELSnA will determine the polarity of the CPWM output. pulse width = 2 x (TPMxCnVH:TPMxCnVL) period = 2 x (TPMxMODH:TPMxMODL); TPMxMODH:TPMxMODL=0x0001-0x7FFF If the channel-value register TPMxCnVH:TPMxCnVL is zero or negative (bit 15 set), the duty cycle will be 0%. If TPMxCnVH:TPMxCnVL is a positive value (bit 15 clear) and is greater than the (non-zero) modulus setting, the duty cycle will be 100% because the duty cycle compare will never occur. This implies the usable range of periods set by the modulus register is 0x0001 through 0x7FFE (0x7FFF if you do not need to generate 100% duty cycle). This is not a significant limitation. The resulting period would be much longer than required for normal applications. TPMxMODH:TPMxMODL=0x0000 is a special case that should not be used with center-aligned PWM mode. When CPWMS=0, this case corresponds to the counter running free from 0x0000 through 0xFFFF, but when CPWMS=1 the counter needs a valid match to the modulus register somewhere other than at 0x0000 in order to change directions from up-counting to down-counting. The output compare value in the TPM channel registers (times 2) determines the pulse width (duty cycle) of the CPWM signal (Figure 16-16). If ELSnA=0, a compare occurred while counting up forces the CPWM output signal low and a compare occurred while counting down forces the output high. The counter counts up until it reaches the modulo setting in TPMxMODH:TPMxMODL, then counts down until it reaches zero. This sets the period equal to two times TPMxMODH:TPMxMODL. COUNT= 0 OUTPUT COUNT= COMPARE TPMxMODH:TPMxMODL (COUNT DOWN) OUTPUT COMPARE (COUNT UP) COUNT= TPMxMODH:TPMxMODL TPMxCHn PULSE WIDTH 2 x TPMxCnVH:TPMxCnVL PERIOD 2 x TPMxMODH:TPMxMODL Figure 16-16. CPWM Period and Pulse Width (ELSnA=0) Center-aligned PWM outputs typically produce less noise than edge-aligned PWMs because fewer I/O pin transitions are lined up at the same system clock edge. This type of PWM is also required for some types of motor drives. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 339 Chapter 16 Timer/PWM Module (S08TPMV3) Input capture, output compare, and edge-aligned PWM functions do not make sense when the counter is operating in up/down counting mode so this implies that all active channels within a TPM must be used in CPWM mode when CPWMS=1. The TPM may be used in an 8-bit MCU. The settings in the timer channel registers are buffered to ensure coherent 16-bit updates and to avoid unexpected PWM pulse widths. Writes to any of the registers TPMxMODH, TPMxMODL, TPMxCnVH, and TPMxCnVL, actually write to buffer registers. In center-aligned PWM mode, the TPMxCnVH:L registers are updated with the value of their write buffer according to the value of CLKSB:CLKSA bits, so: * If (CLKSB:CLKSA = 0:0), the registers are updated when the second byte is written * If (CLKSB:CLKSA not = 0:0), the registers are updated after the both bytes were written, and the TPM counter changes from (TPMxMODH:TPMxMODL - 1) to (TPMxMODH:TPMxMODL). If the TPM counter is a free-running counter, the update is made when the TPM counter changes from 0xFFFE to 0xFFFF. When TPMxCNTH:TPMxCNTL=TPMxMODH:TPMxMODL, the TPM can optionally generate a TOF interrupt (at the end of this count). Writing to TPMxSC cancels any values written to TPMxMODH and/or TPMxMODL and resets the coherency mechanism for the modulo registers. Writing to TPMxCnSC cancels any values written to the channel value registers and resets the coherency mechanism for TPMxCnVH:TPMxCnVL. 16.5 16.5.1 Reset Overview General The TPM is reset whenever any MCU reset occurs. 16.5.2 Description of Reset Operation Reset clears the TPMxSC register which disables clocks to the TPM and disables timer overflow interrupts (TOIE=0). CPWMS, MSnB, MSnA, ELSnB, and ELSnA are all cleared which configures all TPM channels for input-capture operation with the associated pins disconnected from I/O pin logic (so all MCU pins related to the TPM revert to general purpose I/O pins). 16.6 16.6.1 Interrupts General The TPM generates an optional interrupt for the main counter overflow and an interrupt for each channel. The meaning of channel interrupts depends on each channel's mode of operation. If the channel is configured for input capture, the interrupt flag is set each time the selected input capture edge is recognized. If the channel is configured for output compare or PWM modes, the interrupt flag is set each time the main timer counter matches the value in the 16-bit channel value register. MC9S08DZ60 Series Data Sheet, Rev. 4 340 Freescale Semiconductor Chapter 16 Timer/PWM Module (S08TPMV3) All TPM interrupts are listed in Table 16-8 which shows the interrupt name, the name of any local enable that can block the interrupt request from leaving the TPM and getting recognized by the separate interrupt processing logic. Table 16-8. Interrupt Summary Interrupt Local Enable Source Description TOF TOIE Counter overflow Set each time the timer counter reaches its terminal count (at transition to next count value which is usually 0x0000) CHnF CHnIE Channel event An input capture or output compare event took place on channel n The TPM module will provide a high-true interrupt signal. Vectors and priorities are determined at chip integration time in the interrupt module so refer to the user's guide for the interrupt module or to the chip's complete documentation for details. 16.6.2 Description of Interrupt Operation For each interrupt source in the TPM, a flag bit is set upon recognition of the interrupt condition such as timer overflow, channel-input capture, or output-compare events. This flag may be read (polled) by software to determine that the action has occurred, or an associated enable bit (TOIE or CHnIE) can be set to enable hardware interrupt generation. While the interrupt enable bit is set, a static interrupt will generate whenever the associated interrupt flag equals one. The user's software must perform a sequence of steps to clear the interrupt flag before returning from the interrupt-service routine. TPM interrupt flags are cleared by a two-step process including a read of the flag bit while it is set (1) followed by a write of zero (0) to the bit. If a new event is detected between these two steps, the sequence is reset and the interrupt flag remains set after the second step to avoid the possibility of missing the new event. 16.6.2.1 Timer Overflow Interrupt (TOF) Description The meaning and details of operation for TOF interrupts varies slightly depending upon the mode of operation of the TPM system (general purpose timing functions versus center-aligned PWM operation). The flag is cleared by the two step sequence described above. 16.6.2.1.1 Normal Case Normally TOF is set when the timer counter changes from 0xFFFF to 0x0000. When the TPM is not configured for center-aligned PWM (CPWMS=0), TOF gets set when the timer counter changes from the terminal count (the value in the modulo register) to 0x0000. This case corresponds to the normal meaning of counter overflow. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 341 Chapter 16 Timer/PWM Module (S08TPMV3) 16.6.2.1.2 Center-Aligned PWM Case When CPWMS=1, TOF gets set when the timer counter changes direction from up-counting to down-counting at the end of the terminal count (the value in the modulo register). In this case the TOF corresponds to the end of a PWM period. 16.6.2.2 Channel Event Interrupt Description The meaning of channel interrupts depends on the channel's current mode (input-capture, output-compare, edge-aligned PWM, or center-aligned PWM). 16.6.2.2.1 Input Capture Events When a channel is configured as an input capture channel, the ELSnB:ELSnA control bits select no edge (off), rising edges, falling edges or any edge as the edge which triggers an input capture event. When the selected edge is detected, the interrupt flag is set. The flag is cleared by the two-step sequence described in Section 16.6.2, "Description of Interrupt Operation." 16.6.2.2.2 Output Compare Events When a channel is configured as an output compare channel, the interrupt flag is set each time the main timer counter matches the 16-bit value in the channel value register. The flag is cleared by the two-step sequence described Section 16.6.2, "Description of Interrupt Operation." 16.6.2.2.3 PWM End-of-Duty-Cycle Events For channels configured for PWM operation there are two possibilities. When the channel is configured for edge-aligned PWM, the channel flag gets set when the timer counter matches the channel value register which marks the end of the active duty cycle period. When the channel is configured for center-aligned PWM, the timer count matches the channel value register twice during each PWM cycle. In this CPWM case, the channel flag is set at the start and at the end of the active duty cycle period which are the times when the timer counter matches the channel value register. The flag is cleared by the two-step sequence described Section 16.6.2, "Description of Interrupt Operation." 16.7 The Differences from TPM v2 to TPM v3 1. Write to TPMxCNTH:L registers (Section 16.3.2, "TPM-Counter Registers (TPMxCNTH:TPMxCNTL)) [SE110-TPM case 7] Any write to TPMxCNTH or TPMxCNTL registers in TPM v3 clears the TPM counter (TPMxCNTH:L) and the prescaler counter. Instead, in the TPM v2 only the TPM counter is cleared in this case. 2. Read of TPMxCNTH:L registers (Section 16.3.2, "TPM-Counter Registers (TPMxCNTH:TPMxCNTL)) -- In TPM v3, any read of TPMxCNTH:L registers during BDM mode returns the value of the TPM counter that is frozen. In TPM v2, if only one byte of the TPMxCNTH:L registers was read before the BDM mode became active, then any read of TPMxCNTH:L registers during MC9S08DZ60 Series Data Sheet, Rev. 4 342 Freescale Semiconductor Chapter 16 Timer/PWM Module (S08TPMV3) BDM mode returns the latched value of TPMxCNTH:L from the read buffer instead of the frozen TPM counter value. -- This read coherency mechanism is cleared in TPM v3 in BDM mode if there is a write to TPMxSC, TPMxCNTH or TPMxCNTL. Instead, in these conditions the TPM v2 does not clear this read coherency mechanism. 3. Read of TPMxCnVH:L registers (Section 16.3.5, "TPM Channel Value Registers (TPMxCnVH:TPMxCnVL)) -- In TPM v3, any read of TPMxCnVH:L registers during BDM mode returns the value of the TPMxCnVH:L register. In TPM v2, if only one byte of the TPMxCnVH:L registers was read before the BDM mode became active, then any read of TPMxCnVH:L registers during BDM mode returns the latched value of TPMxCNTH:L from the read buffer instead of the value in the TPMxCnVH:L registers. -- This read coherency mechanism is cleared in TPM v3 in BDM mode if there is a write to TPMxCnSC. Instead, in this condition the TPM v2 does not clear this read coherency mechanism. 4. Write to TPMxCnVH:L registers -- Input Capture Mode (Section 16.4.2.1, "Input Capture Mode) In this mode the TPM v3 does not allow the writes to TPMxCnVH:L registers. Instead, the TPM v2 allows these writes. -- Output Compare Mode (Section 16.4.2.2, "Output Compare Mode) In this mode and if (CLKSB:CLKSA not = 0:0), the TPM v3 updates the TPMxCnVH:L registers with the value of their write buffer at the next change of the TPM counter (end of the prescaler counting) after the second byte is written. Instead, the TPM v2 always updates these registers when their second byte is written. The following procedure can be used in the TPM v3 to verify if the TPMxCnVH:L registers were updated with the new value that was written to these registers (value in their write buffer). ... write the new value to TPMxCnVH:L; read TPMxCnVH and TPMxCnVL registers; while (the read value of TPMxCnVH:L is different from the new value written to TPMxCnVH:L) begin read again TPMxCnVH and TPMxCnVL; end ... In this point, the TPMxCnVH:L registers were updated, so the program can continue and, for example, write to TPMxC0SC without cancelling the previous write to TPMxCnVH:L registers. -- Edge-Aligned PWM (Section 16.4.2.3, "Edge-Aligned PWM Mode) In this mode and if (CLKSB:CLKSA not = 00), the TPM v3 updates the TPMxCnVH:L registers with the value of their write buffer after that the both bytes were written and when the MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 343 Chapter 16 Timer/PWM Module (S08TPMV3) TPM counter changes from (TPMxMODH:L - 1) to (TPMxMODH:L). If the TPM counter is a free-running counter, then this update is made when the TPM counter changes from $FFFE to $FFFF. Instead, the TPM v2 makes this update after that the both bytes were written and when the TPM counter changes from TPMxMODH:L to $0000. -- Center-Aligned PWM (Section 16.4.2.4, "Center-Aligned PWM Mode) In this mode and if (CLKSB:CLKSA not = 00), the TPM v3 updates the TPMxCnVH:L registers with the value of their write buffer after that the both bytes were written and when the TPM counter changes from (TPMxMODH:L - 1) to (TPMxMODH:L). If the TPM counter is a free-running counter, then this update is made when the TPM counter changes from $FFFE to $FFFF. Instead, the TPM v2 makes this update after that the both bytes were written and when the TPM counter changes from TPMxMODH:L to (TPMxMODH:L - 1). 5. Center-Aligned PWM (Section 16.4.2.4, "Center-Aligned PWM Mode) -- TPMxCnVH:L = TPMxMODH:L [SE110-TPM case 1] In this case, the TPM v3 produces 100% duty cycle. Instead, the TPM v2 produces 0% duty cycle. -- TPMxCnVH:L = (TPMxMODH:L - 1) [SE110-TPM case 2] In this case, the TPM v3 produces almost 100% duty cycle. Instead, the TPM v2 produces 0% duty cycle. -- TPMxCnVH:L is changed from 0x0000 to a non-zero value [SE110-TPM case 3 and 5] In this case, the TPM v3 waits for the start of a new PWM period to begin using the new duty cycle setting. Instead, the TPM v2 changes the channel output at the middle of the current PWM period (when the count reaches 0x0000). -- TPMxCnVH:L is changed from a non-zero value to 0x0000 [SE110-TPM case 4] In this case, the TPM v3 finishes the current PWM period using the old duty cycle setting. Instead, the TPM v2 finishes the current PWM period using the new duty cycle setting. 6. Write to TPMxMODH:L registers in BDM mode (Section 16.3.3, "TPM Counter Modulo Registers (TPMxMODH:TPMxMODL)) In the TPM v3 a write to TPMxSC register in BDM mode clears the write coherency mechanism of TPMxMODH:L registers. Instead, in the TPM v2 this coherency mechanism is not cleared when there is a write to TPMxSC register. 7. Update of EPWM signal when CLKSB:CLKSA = 00 In the TPM v3 if CLKSB:CLKSA = 00, then the EPWM signal in the channel output is not update (it is frozen while CLKSB:CLKSA = 00). Instead, in the TPM v2 the EPWM signal is updated at the next rising edge of bus clock after a write to TPMxCnSC register. The Figure 0-1 and Figure 0-2 show when the EPWM signals generated by TPM v2 and TPM v3 after the reset (CLKSB:CLKSA = 00) and if there is a write to TPMxCnSC register. MC9S08DZ60 Series Data Sheet, Rev. 4 344 Freescale Semiconductor Chapter 16 Timer/PWM Module (S08TPMV3) EPWM mode TPMxMODH:TPMxMODL = 0x0007 TPMxCnVH:TPMxCnVL = 0x0005 RESET (active low) BUS CLOCK TPMxCNTH:TPMxCNTL 0 1 2 3 4 5 00 CLKSB:CLKSA BITS 6 7 0 1 2 ... 01 MSnB:MSnA BITS 00 10 ELSnB:ELSnA BITS 00 10 TPMv2 TPMxCHn TPMv3 TPMxCHn CHnF BIT (in TPMv2 and TPMv3) Figure 0-1. Generation of high-true EPWM signal by TPM v2 and v3 after the reset EPWM mode TPMxMODH:TPMxMODL = 0x0007 TPMxCnVH:TPMxCnVL = 0x0005 RESET (active low) BUS CLOCK TPMxCNTH:TPMxCNTL 0 1 3 4 5 6 7 0 1 2 ... 01 00 CLKSB:CLKSA BITS 2 MSnB:MSnA BITS 00 10 ELSnB:ELSnA BITS 00 01 TPMv2 TPMxCHn TPMv3 TPMxCHn CHnF BIT (in TPMv2 and TPMv3) Figure 0-2. Generation of low-true EPWM signal by TPM v2 and v3 after the reset The following procedure can be used in TPM v3 (when the channel pin is also a port pin) to emulate the high-true EPWM generated by TPM v2 after the reset. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 345 Chapter 16 Timer/PWM Module (S08TPMV3) ... configure the channel pin as output port pin and set the output pin; configure the channel to generate the EPWM signal but keep ELSnB:ELSnA as 00; configure the other registers (TPMxMODH, TPMxMODL, TPMxCnVH, TPMxCnVL, ...); configure CLKSB:CLKSA bits (TPM v3 starts to generate the high-true EPWM signal, however TPM does not control the channel pin, so the EPWM signal is not available); wait until the TOF is set (or use the TOF interrupt); enable the channel output by configuring ELSnB:ELSnA bits (now EPWM signal is available); ... MC9S08DZ60 Series Data Sheet, Rev. 4 346 Freescale Semiconductor Chapter 17 Development Support 17.1 Introduction Development support systems in the HCS08 include the background debug controller (BDC) and the on-chip debug module (DBG). The BDC provides a single-wire debug interface to the target MCU that provides a convenient interface for programming the on-chip Flash and other nonvolatile memories. The BDC is also the primary debug interface for development and allows non-intrusive access to memory data and traditional debug features such as CPU register modify, breakpoints, and single instruction trace commands. In the HCS08 Family, address and data bus signals are not available on external pins (not even in test modes). Debug is done through commands fed into the target MCU via the single-wire background debug interface. The debug module provides a means to selectively trigger and capture bus information so an external development system can reconstruct what happened inside the MCU on a cycle-by-cycle basis without having external access to the address and data signals. 17.1.1 Forcing Active Background The method for forcing active background mode depends on the specific HCS08 derivative. For the MC9S08DZ60, you can force active background after a power-on reset by holding the BKGD pin low as the device exits the reset condition. You can also force active background by driving BKGD low immediately after a serial background command that writes a one to the BDFR bit in the SBDFR register. If no debug pod is connected to the BKGD pin, the MCU will always reset into normal operating mode. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 347 Chapter 17 Development Support 17.1.2 Features Features of the BDC module include: * Single pin for mode selection and background communications * BDC registers are not located in the memory map * SYNC command to determine target communications rate * Non-intrusive commands for memory access * Active background mode commands for CPU register access * GO and TRACE1 commands * BACKGROUND command can wake CPU from stop or wait modes * One hardware address breakpoint built into BDC * Oscillator runs in stop mode, if BDC enabled * COP watchdog disabled while in active background mode Features of the ICE system include: * * * * 17.2 Two trigger comparators: Two address + read/write (R/W) or one full address + data + R/W Flexible 8-word by 16-bit FIFO (first-in, first-out) buffer for capture information: -- Change-of-flow addresses or -- Event-only data Two types of breakpoints: -- Tag breakpoints for instruction opcodes -- Force breakpoints for any address access Nine trigger modes: -- Basic: A-only, A OR B -- Sequence: A then B -- Full: A AND B data, A AND NOT B data -- Event (store data): Event-only B, A then event-only B -- Range: Inside range (A address B), outside range (address < A or address > B) Background Debug Controller (BDC) All MCUs in the HCS08 Family contain a single-wire background debug interface that supports in-circuit programming of on-chip nonvolatile memory and sophisticated non-intrusive debug capabilities. Unlike debug interfaces on earlier 8-bit MCUs, this system does not interfere with normal application resources. It does not use any user memory or locations in the memory map and does not share any on-chip peripherals. BDC commands are divided into two groups: * Active background mode commands require that the target MCU is in active background mode (the user program is not running). Active background mode commands allow the CPU registers to be read or written, and allow the user to trace one user instruction at a time, or GO to the user program from active background mode. MC9S08DZ60 Series Data Sheet, Rev. 4 348 Freescale Semiconductor Chapter 17 Development Support * Non-intrusive commands can be executed at any time even while the user's program is running. Non-intrusive commands allow a user to read or write MCU memory locations or access status and control registers within the background debug controller. Typically, a relatively simple interface pod is used to translate commands from a host computer into commands for the custom serial interface to the single-wire background debug system. Depending on the development tool vendor, this interface pod may use a standard RS-232 serial port, a parallel printer port, or some other type of communications such as a universal serial bus (USB) to communicate between the host PC and the pod. The pod typically connects to the target system with ground, the BKGD pin, RESET, and sometimes VDD. An open-drain connection to reset allows the host to force a target system reset, which is useful to regain control of a lost target system or to control startup of a target system before the on-chip nonvolatile memory has been programmed. Sometimes VDD can be used to allow the pod to use power from the target system to avoid the need for a separate power supply. However, if the pod is powered separately, it can be connected to a running target system without forcing a target system reset or otherwise disturbing the running application program. BKGD 1 2 GND NO CONNECT 3 4 RESET NO CONNECT 5 6 VDD Figure 17-1. BDM Tool Connector 17.2.1 BKGD Pin Description BKGD is the single-wire background debug interface pin. The primary function of this pin is for bidirectional serial communication of active background mode commands and data. During reset, this pin is used to select between starting in active background mode or starting the user's application program. This pin is also used to request a timed sync response pulse to allow a host development tool to determine the correct clock frequency for background debug serial communications. BDC serial communications use a custom serial protocol first introduced on the M68HC12 Family of microcontrollers. This protocol assumes the host knows the communication clock rate that is determined by the target BDC clock rate. All communication is initiated and controlled by the host that drives a high-to-low edge to signal the beginning of each bit time. Commands and data are sent most significant bit first (MSB first). For a detailed description of the communications protocol, refer to Section 17.2.2, "Communication Details." If a host is attempting to communicate with a target MCU that has an unknown BDC clock rate, a SYNC command may be sent to the target MCU to request a timed sync response signal from which the host can determine the correct communication speed. BKGD is a pseudo-open-drain pin and there is an on-chip pullup so no external pullup resistor is required. Unlike typical open-drain pins, the external RC time constant on this pin, which is influenced by external capacitance, plays almost no role in signal rise time. The custom protocol provides for brief, actively driven speedup pulses to force rapid rise times on this pin without risking harmful drive level conflicts. Refer to Section 17.2.2, "Communication Details," for more detail. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 349 Chapter 17 Development Support When no debugger pod is connected to the 6-pin BDM interface connector, the internal pullup on BKGD chooses normal operating mode. When a debug pod is connected to BKGD it is possible to force the MCU into active background mode after reset. The specific conditions for forcing active background depend upon the HCS08 derivative (refer to the introduction to this Development Support section). It is not necessary to reset the target MCU to communicate with it through the background debug interface. 17.2.2 Communication Details The BDC serial interface requires the external controller to generate a falling edge on the BKGD pin to indicate the start of each bit time. The external controller provides this falling edge whether data is transmitted or received. BKGD is a pseudo-open-drain pin that can be driven either by an external controller or by the MCU. Data is transferred MSB first at 16 BDC clock cycles per bit (nominal speed). The interface times out if 512 BDC clock cycles occur between falling edges from the host. Any BDC command that was in progress when this timeout occurs is aborted without affecting the memory or operating mode of the target MCU system. The custom serial protocol requires the debug pod to know the target BDC communication clock speed. The clock switch (CLKSW) control bit in the BDC status and control register allows the user to select the BDC clock source. The BDC clock source can either be the bus or the alternate BDC clock source. The BKGD pin can receive a high or low level or transmit a high or low level. The following diagrams show timing for each of these cases. Interface timing is synchronous to clocks in the target BDC, but asynchronous to the external host. The internal BDC clock signal is shown for reference in counting cycles. MC9S08DZ60 Series Data Sheet, Rev. 4 350 Freescale Semiconductor Chapter 17 Development Support Figure 17-2 shows an external host transmitting a logic 1 or 0 to the BKGD pin of a target HCS08 MCU. The host is asynchronous to the target so there is a 0-to-1 cycle delay from the host-generated falling edge to where the target perceives the beginning of the bit time. Ten target BDC clock cycles later, the target senses the bit level on the BKGD pin. Typically, the host actively drives the pseudo-open-drain BKGD pin during host-to-target transmissions to speed up rising edges. Because the target does not drive the BKGD pin during the host-to-target transmission period, there is no need to treat the line as an open-drain signal during this period. BDC CLOCK (TARGET MCU) HOST TRANSMIT 1 HOST TRANSMIT 0 10 CYCLES SYNCHRONIZATION UNCERTAINTY EARLIEST START OF NEXT BIT TARGET SENSES BIT LEVEL PERCEIVED START OF BIT TIME Figure 17-2. BDC Host-to-Target Serial Bit Timing MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 351 Chapter 17 Development Support Figure 17-3 shows the host receiving a logic 1 from the target HCS08 MCU. Because the host is asynchronous to the target MCU, there is a 0-to-1 cycle delay from the host-generated falling edge on BKGD to the perceived start of the bit time in the target MCU. The host holds the BKGD pin low long enough for the target to recognize it (at least two target BDC cycles). The host must release the low drive before the target MCU drives a brief active-high speedup pulse seven cycles after the perceived start of the bit time. The host should sample the bit level about 10 cycles after it started the bit time. BDC CLOCK (TARGET MCU) HOST DRIVE TO BKGD PIN HIGH-IMPEDANCE TARGET MCU SPEEDUP PULSE HIGH-IMPEDANCE HIGH-IMPEDANCE PERCEIVED START OF BIT TIME R-C RISE BKGD PIN 10 CYCLES 10 CYCLES EARLIEST START OF NEXT BIT HOST SAMPLES BKGD PIN Figure 17-3. BDC Target-to-Host Serial Bit Timing (Logic 1) MC9S08DZ60 Series Data Sheet, Rev. 4 352 Freescale Semiconductor Chapter 17 Development Support Figure 17-4 shows the host receiving a logic 0 from the target HCS08 MCU. Because the host is asynchronous to the target MCU, there is a 0-to-1 cycle delay from the host-generated falling edge on BKGD to the start of the bit time as perceived by the target MCU. The host initiates the bit time but the target HCS08 finishes it. Because the target wants the host to receive a logic 0, it drives the BKGD pin low for 13 BDC clock cycles, then briefly drives it high to speed up the rising edge. The host samples the bit level about 10 cycles after starting the bit time. BDC CLOCK (TARGET MCU) HOST DRIVE TO BKGD PIN HIGH-IMPEDANCE SPEEDUP PULSE TARGET MCU DRIVE AND SPEED-UP PULSE PERCEIVED START OF BIT TIME BKGD PIN 10 CYCLES 10 CYCLES EARLIEST START OF NEXT BIT HOST SAMPLES BKGD PIN Figure 17-4. BDM Target-to-Host Serial Bit Timing (Logic 0) MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 353 Chapter 17 Development Support 17.2.3 BDC Commands BDC commands are sent serially from a host computer to the BKGD pin of the target HCS08 MCU. All commands and data are sent MSB-first using a custom BDC communications protocol. Active background mode commands require that the target MCU is currently in the active background mode while non-intrusive commands may be issued at any time whether the target MCU is in active background mode or running a user application program. Table 17-1 shows all HCS08 BDC commands, a shorthand description of their coding structure, and the meaning of each command. Coding Structure Nomenclature This nomenclature is used in Table 17-1 to describe the coding structure of the BDC commands. Commands begin with an 8-bit hexadecimal command code in the host-to-target direction (most significant bit first) / = separates parts of the command d = delay 16 target BDC clock cycles AAAA = a 16-bit address in the host-to-target direction RD = 8 bits of read data in the target-to-host direction WD = 8 bits of write data in the host-to-target direction RD16 = 16 bits of read data in the target-to-host direction WD16 = 16 bits of write data in the host-to-target direction SS = the contents of BDCSCR in the target-to-host direction (STATUS) CC = 8 bits of write data for BDCSCR in the host-to-target direction (CONTROL) RBKP = 16 bits of read data in the target-to-host direction (from BDCBKPT breakpoint register) WBKP = 16 bits of write data in the host-to-target direction (for BDCBKPT breakpoint register) MC9S08DZ60 Series Data Sheet, Rev. 4 354 Freescale Semiconductor Chapter 17 Development Support Table 17-1. BDC Command Summary Command Mnemonic 1 Active BDM/ Non-intrusive Coding Structure Description SYNC Non-intrusive n/a1 Request a timed reference pulse to determine target BDC communication speed ACK_ENABLE Non-intrusive D5/d Enable acknowledge protocol. Refer to Freescale document order no. HCS08RMv1/D. ACK_DISABLE Non-intrusive D6/d Disable acknowledge protocol. Refer to Freescale document order no. HCS08RMv1/D. BACKGROUND Non-intrusive 90/d Enter active background mode if enabled (ignore if ENBDM bit equals 0) READ_STATUS Non-intrusive E4/SS Read BDC status from BDCSCR WRITE_CONTROL Non-intrusive C4/CC Write BDC controls in BDCSCR READ_BYTE Non-intrusive E0/AAAA/d/RD Read a byte from target memory READ_BYTE_WS Non-intrusive E1/AAAA/d/SS/RD Read a byte and report status READ_LAST Non-intrusive E8/SS/RD Re-read byte from address just read and report status WRITE_BYTE Non-intrusive C0/AAAA/WD/d Write a byte to target memory WRITE_BYTE_WS Non-intrusive C1/AAAA/WD/d/SS Write a byte and report status READ_BKPT Non-intrusive E2/RBKP Read BDCBKPT breakpoint register WRITE_BKPT Non-intrusive C2/WBKP Write BDCBKPT breakpoint register GO Active BDM 08/d Go to execute the user application program starting at the address currently in the PC TRACE1 Active BDM 10/d Trace 1 user instruction at the address in the PC, then return to active background mode TAGGO Active BDM 18/d Same as GO but enable external tagging (HCS08 devices have no external tagging pin) READ_A Active BDM 68/d/RD Read accumulator (A) READ_CCR Active BDM 69/d/RD Read condition code register (CCR) READ_PC Active BDM 6B/d/RD16 Read program counter (PC) READ_HX Active BDM 6C/d/RD16 Read H and X register pair (H:X) READ_SP Active BDM 6F/d/RD16 Read stack pointer (SP) READ_NEXT Active BDM 70/d/RD Increment H:X by one then read memory byte located at H:X READ_NEXT_WS Active BDM 71/d/SS/RD Increment H:X by one then read memory byte located at H:X. Report status and data. WRITE_A Active BDM 48/WD/d Write accumulator (A) WRITE_CCR Active BDM 49/WD/d Write condition code register (CCR) WRITE_PC Active BDM 4B/WD16/d Write program counter (PC) WRITE_HX Active BDM 4C/WD16/d Write H and X register pair (H:X) WRITE_SP Active BDM 4F/WD16/d Write stack pointer (SP) WRITE_NEXT Active BDM 50/WD/d Increment H:X by one, then write memory byte located at H:X WRITE_NEXT_WS Active BDM 51/WD/d/SS Increment H:X by one, then write memory byte located at H:X. Also report status. The SYNC command is a special operation that does not have a command code. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 355 Chapter 17 Development Support The SYNC command is unlike other BDC commands because the host does not necessarily know the correct communications speed to use for BDC communications until after it has analyzed the response to the SYNC command. To issue a SYNC command, the host: * Drives the BKGD pin low for at least 128 cycles of the slowest possible BDC clock (The slowest clock is normally the reference oscillator/64 or the self-clocked rate/64.) * Drives BKGD high for a brief speedup pulse to get a fast rise time (This speedup pulse is typically one cycle of the fastest clock in the system.) * Removes all drive to the BKGD pin so it reverts to high impedance * Monitors the BKGD pin for the sync response pulse The target, upon detecting the SYNC request from the host (which is a much longer low time than would ever occur during normal BDC communications): * Waits for BKGD to return to a logic high * Delays 16 cycles to allow the host to stop driving the high speedup pulse * Drives BKGD low for 128 BDC clock cycles * Drives a 1-cycle high speedup pulse to force a fast rise time on BKGD * Removes all drive to the BKGD pin so it reverts to high impedance The host measures the low time of this 128-cycle sync response pulse and determines the correct speed for subsequent BDC communications. Typically, the host can determine the correct communication speed within a few percent of the actual target speed and the communication protocol can easily tolerate speed errors of several percent. 17.2.4 BDC Hardware Breakpoint The BDC includes one relatively simple hardware breakpoint that compares the CPU address bus to a 16-bit match value in the BDCBKPT register. This breakpoint can generate a forced breakpoint or a tagged breakpoint. A forced breakpoint causes the CPU to enter active background mode at the first instruction boundary following any access to the breakpoint address. The tagged breakpoint causes the instruction opcode at the breakpoint address to be tagged so that the CPU will enter active background mode rather than executing that instruction if and when it reaches the end of the instruction queue. This implies that tagged breakpoints can only be placed at the address of an instruction opcode while forced breakpoints can be set at any address. The breakpoint enable (BKPTEN) control bit in the BDC status and control register (BDCSCR) is used to enable the breakpoint logic (BKPTEN = 1). When BKPTEN = 0, its default value after reset, the breakpoint logic is disabled and no BDC breakpoints are requested regardless of the values in other BDC breakpoint registers and control bits. The force/tag select (FTS) control bit in BDCSCR is used to select forced (FTS = 1) or tagged (FTS = 0) type breakpoints. The on-chip debug module (DBG) includes circuitry for two additional hardware breakpoints that are more flexible than the simple breakpoint in the BDC module. MC9S08DZ60 Series Data Sheet, Rev. 4 356 Freescale Semiconductor Chapter 17 Development Support 17.3 On-Chip Debug System (DBG) Because HCS08 devices do not have external address and data buses, the most important functions of an in-circuit emulator have been built onto the chip with the MCU. The debug system consists of an 8-stage FIFO that can store address or data bus information, and a flexible trigger system to decide when to capture bus information and what information to capture. The system relies on the single-wire background debug system to access debug control registers and to read results out of the eight stage FIFO. The debug module includes control and status registers that are accessible in the user's memory map. These registers are located in the high register space to avoid using valuable direct page memory space. Most of the debug module's functions are used during development, and user programs rarely access any of the control and status registers for the debug module. The one exception is that the debug system can provide the means to implement a form of ROM patching. This topic is discussed in greater detail in Section 17.3.6, "Hardware Breakpoints." 17.3.1 Comparators A and B Two 16-bit comparators (A and B) can optionally be qualified with the R/W signal and an opcode tracking circuit. Separate control bits allow you to ignore R/W for each comparator. The opcode tracking circuitry optionally allows you to specify that a trigger will occur only if the opcode at the specified address is actually executed as opposed to only being read from memory into the instruction queue. The comparators are also capable of magnitude comparisons to support the inside range and outside range trigger modes. Comparators are disabled temporarily during all BDC accesses. The A comparator is always associated with the 16-bit CPU address. The B comparator compares to the CPU address or the 8-bit CPU data bus, depending on the trigger mode selected. Because the CPU data bus is separated into a read data bus and a write data bus, the RWAEN and RWA control bits have an additional purpose, in full address plus data comparisons they are used to decide which of these buses to use in the comparator B data bus comparisons. If RWAEN = 1 (enabled) and RWA = 0 (write), the CPU's write data bus is used. Otherwise, the CPU's read data bus is used. The currently selected trigger mode determines what the debugger logic does when a comparator detects a qualified match condition. A match can cause: * Generation of a breakpoint to the CPU * Storage of data bus values into the FIFO * Starting to store change-of-flow addresses into the FIFO (begin type trace) * Stopping the storage of change-of-flow addresses into the FIFO (end type trace) 17.3.2 Bus Capture Information and FIFO Operation The usual way to use the FIFO is to setup the trigger mode and other control options, then arm the debugger. When the FIFO has filled or the debugger has stopped storing data into the FIFO, you would read the information out of it in the order it was stored into the FIFO. Status bits indicate the number of words of valid information that are in the FIFO as data is stored into it. If a trace run is manually halted by writing 0 to ARM before the FIFO is full (CNT = 1:0:0:0), the information is shifted by one position and MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 357 Chapter 17 Development Support the host must perform ((8 - CNT) - 1) dummy reads of the FIFO to advance it to the first significant entry in the FIFO. In most trigger modes, the information stored in the FIFO consists of 16-bit change-of-flow addresses. In these cases, read DBGFH then DBGFL to get one coherent word of information out of the FIFO. Reading DBGFL (the low-order byte of the FIFO data port) causes the FIFO to shift so the next word of information is available at the FIFO data port. In the event-only trigger modes (see Section 17.3.5, "Trigger Modes"), 8-bit data information is stored into the FIFO. In these cases, the high-order half of the FIFO (DBGFH) is not used and data is read out of the FIFO by simply reading DBGFL. Each time DBGFL is read, the FIFO is shifted so the next data value is available through the FIFO data port at DBGFL. In trigger modes where the FIFO is storing change-of-flow addresses, there is a delay between CPU addresses and the input side of the FIFO. Because of this delay, if the trigger event itself is a change-of-flow address or a change-of-flow address appears during the next two bus cycles after a trigger event starts the FIFO, it will not be saved into the FIFO. In the case of an end-trace, if the trigger event is a change-of-flow, it will be saved as the last change-of-flow entry for that debug run. The FIFO can also be used to generate a profile of executed instruction addresses when the debugger is not armed. When ARM = 0, reading DBGFL causes the address of the most-recently fetched opcode to be saved in the FIFO. To use the profiling feature, a host debugger would read addresses out of the FIFO by reading DBGFH then DBGFL at regular periodic intervals. The first eight values would be discarded because they correspond to the eight DBGFL reads needed to initially fill the FIFO. Additional periodic reads of DBGFH and DBGFL return delayed information about executed instructions so the host debugger can develop a profile of executed instruction addresses. 17.3.3 Change-of-Flow Information To minimize the amount of information stored in the FIFO, only information related to instructions that cause a change to the normal sequential execution of instructions is stored. With knowledge of the source and object code program stored in the target system, an external debugger system can reconstruct the path of execution through many instructions from the change-of-flow information stored in the FIFO. For conditional branch instructions where the branch is taken (branch condition was true), the source address is stored (the address of the conditional branch opcode). Because BRA and BRN instructions are not conditional, these events do not cause change-of-flow information to be stored in the FIFO. Indirect JMP and JSR instructions use the current contents of the H:X index register pair to determine the destination address, so the debug system stores the run-time destination address for any indirect JMP or JSR. For interrupts, RTI, or RTS, the destination address is stored in the FIFO as change-of-flow information. 17.3.4 Tag vs. Force Breakpoints and Triggers Tagging is a term that refers to identifying an instruction opcode as it is fetched into the instruction queue, but not taking any other action until and unless that instruction is actually executed by the CPU. This distinction is important because any change-of-flow from a jump, branch, subroutine call, or interrupt causes some instructions that have been fetched into the instruction queue to be thrown away without being executed. MC9S08DZ60 Series Data Sheet, Rev. 4 358 Freescale Semiconductor Chapter 17 Development Support A force-type breakpoint waits for the current instruction to finish and then acts upon the breakpoint request. The usual action in response to a breakpoint is to go to active background mode rather than continuing to the next instruction in the user application program. The tag vs. force terminology is used in two contexts within the debug module. The first context refers to breakpoint requests from the debug module to the CPU. The second refers to match signals from the comparators to the debugger control logic. When a tag-type break request is sent to the CPU, a signal is entered into the instruction queue along with the opcode so that if/when this opcode ever executes, the CPU will effectively replace the tagged opcode with a BGND opcode so the CPU goes to active background mode rather than executing the tagged instruction. When the TRGSEL control bit in the DBGT register is set to select tag-type operation, the output from comparator A or B is qualified by a block of logic in the debug module that tracks opcodes and only produces a trigger to the debugger if the opcode at the compare address is actually executed. There is separate opcode tracking logic for each comparator so more than one compare event can be tracked through the instruction queue at a time. 17.3.5 Trigger Modes The trigger mode controls the overall behavior of a debug run. The 4-bit TRG field in the DBGT register selects one of nine trigger modes. When TRGSEL = 1 in the DBGT register, the output of the comparator must propagate through an opcode tracking circuit before triggering FIFO actions. The BEGIN bit in DBGT chooses whether the FIFO begins storing data when the qualified trigger is detected (begin trace), or the FIFO stores data in a circular fashion from the time it is armed until the qualified trigger is detected (end trigger). A debug run is started by writing a 1 to the ARM bit in the DBGC register, which sets the ARMF flag and clears the AF and BF flags and the CNT bits in DBGS. A begin-trace debug run ends when the FIFO gets full. An end-trace run ends when the selected trigger event occurs. Any debug run can be stopped manually by writing a 0 to ARM or DBGEN in DBGC. In all trigger modes except event-only modes, the FIFO stores change-of-flow addresses. In event-only trigger modes, the FIFO stores data in the low-order eight bits of the FIFO. The BEGIN control bit is ignored in event-only trigger modes and all such debug runs are begin type traces. When TRGSEL = 1 to select opcode fetch triggers, it is not necessary to use R/W in comparisons because opcode tags would only apply to opcode fetches that are always read cycles. It would also be unusual to specify TRGSEL = 1 while using a full mode trigger because the opcode value is normally known at a particular address. The following trigger mode descriptions only state the primary comparator conditions that lead to a trigger. Either comparator can usually be further qualified with R/W by setting RWAEN (RWBEN) and the corresponding RWA (RWB) value to be matched against R/W. The signal from the comparator with optional R/W qualification is used to request a CPU breakpoint if BRKEN = 1 and TAG determines whether the CPU request will be a tag request or a force request. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 359 Chapter 17 Development Support A-Only -- Trigger when the address matches the value in comparator A A OR B -- Trigger when the address matches either the value in comparator A or the value in comparator B A Then B -- Trigger when the address matches the value in comparator B but only after the address for another cycle matched the value in comparator A. There can be any number of cycles after the A match and before the B match. A AND B Data (Full Mode) -- This is called a full mode because address, data, and R/W (optionally) must match within the same bus cycle to cause a trigger event. Comparator A checks address, the low byte of comparator B checks data, and R/W is checked against RWA if RWAEN = 1. The high-order half of comparator B is not used. In full trigger modes it is not useful to specify a tag-type CPU breakpoint (BRKEN = TAG = 1), but if you do, the comparator B data match is ignored for the purpose of issuing the tag request to the CPU and the CPU breakpoint is issued when the comparator A address matches. A AND NOT B Data (Full Mode) -- Address must match comparator A, data must not match the low half of comparator B, and R/W must match RWA if RWAEN = 1. All three conditions must be met within the same bus cycle to cause a trigger. In full trigger modes it is not useful to specify a tag-type CPU breakpoint (BRKEN = TAG = 1), but if you do, the comparator B data match is ignored for the purpose of issuing the tag request to the CPU and the CPU breakpoint is issued when the comparator A address matches. Event-Only B (Store Data) -- Trigger events occur each time the address matches the value in comparator B. Trigger events cause the data to be captured into the FIFO. The debug run ends when the FIFO becomes full. A Then Event-Only B (Store Data) -- After the address has matched the value in comparator A, a trigger event occurs each time the address matches the value in comparator B. Trigger events cause the data to be captured into the FIFO. The debug run ends when the FIFO becomes full. Inside Range (A Address B) -- A trigger occurs when the address is greater than or equal to the value in comparator A and less than or equal to the value in comparator B at the same time. Outside Range (Address < A or Address > B) -- A trigger occurs when the address is either less than the value in comparator A or greater than the value in comparator B. MC9S08DZ60 Series Data Sheet, Rev. 4 360 Freescale Semiconductor Chapter 17 Development Support 17.3.6 Hardware Breakpoints The BRKEN control bit in the DBGC register may be set to 1 to allow any of the trigger conditions described in Section 17.3.5, "Trigger Modes," to be used to generate a hardware breakpoint request to the CPU. TAG in DBGC controls whether the breakpoint request will be treated as a tag-type breakpoint or a force-type breakpoint. A tag breakpoint causes the current opcode to be marked as it enters the instruction queue. If a tagged opcode reaches the end of the pipe, the CPU executes a BGND instruction to go to active background mode rather than executing the tagged opcode. A force-type breakpoint causes the CPU to finish the current instruction and then go to active background mode. If the background mode has not been enabled (ENBDM = 1) by a serial WRITE_CONTROL command through the BKGD pin, the CPU will execute an SWI instruction instead of going to active background mode. 17.4 Register Definition This section contains the descriptions of the BDC and DBG registers and control bits. Refer to the high-page register summary in the device overview chapter of this data sheet for the absolute address assignments for all DBG registers. This section refers to registers and control bits only by their names. A Freescale-provided equate or header file is used to translate these names into the appropriate absolute addresses. 17.4.1 BDC Registers and Control Bits The BDC has two registers: * The BDC status and control register (BDCSCR) is an 8-bit register containing control and status bits for the background debug controller. * The BDC breakpoint match register (BDCBKPT) holds a 16-bit breakpoint match address. These registers are accessed with dedicated serial BDC commands and are not located in the memory space of the target MCU (so they do not have addresses and cannot be accessed by user programs). Some of the bits in the BDCSCR have write limitations; otherwise, these registers may be read or written at any time. For example, the ENBDM control bit may not be written while the MCU is in active background mode. (This prevents the ambiguous condition of the control bit forbidding active background mode while the MCU is already in active background mode.) Also, the four status bits (BDMACT, WS, WSF, and DVF) are read-only status indicators and can never be written by the WRITE_CONTROL serial BDC command. The clock switch (CLKSW) control bit may be read or written at any time. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 361 Chapter 17 Development Support 17.4.1.1 BDC Status and Control Register (BDCSCR) This register can be read or written by serial BDC commands (READ_STATUS and WRITE_CONTROL) but is not accessible to user programs because it is not located in the normal memory map of the MCU. 7 R 6 5 4 3 BKPTEN FTS CLKSW BDMACT ENBDM 2 1 0 WS WSF DVF W Normal Reset 0 0 0 0 0 0 0 0 Reset in Active BDM: 1 1 0 0 1 0 0 0 = Unimplemented or Reserved Figure 17-5. BDC Status and Control Register (BDCSCR) Table 17-2. BDCSCR Register Field Descriptions Field Description 7 ENBDM Enable BDM (Permit Active Background Mode) -- Typically, this bit is written to 1 by the debug host shortly after the beginning of a debug session or whenever the debug host resets the target and remains 1 until a normal reset clears it. 0 BDM cannot be made active (non-intrusive commands still allowed) 1 BDM can be made active to allow active background mode commands 6 BDMACT Background Mode Active Status -- This is a read-only status bit. 0 BDM not active (user application program running) 1 BDM active and waiting for serial commands 5 BKPTEN BDC Breakpoint Enable -- If this bit is clear, the BDC breakpoint is disabled and the FTS (force tag select) control bit and BDCBKPT match register are ignored. 0 BDC breakpoint disabled 1 BDC breakpoint enabled 4 FTS 3 CLKSW Force/Tag Select -- When FTS = 1, a breakpoint is requested whenever the CPU address bus matches the BDCBKPT match register. When FTS = 0, a match between the CPU address bus and the BDCBKPT register causes the fetched opcode to be tagged. If this tagged opcode ever reaches the end of the instruction queue, the CPU enters active background mode rather than executing the tagged opcode. 0 Tag opcode at breakpoint address and enter active background mode if CPU attempts to execute that instruction 1 Breakpoint match forces active background mode at next instruction boundary (address need not be an opcode) Select Source for BDC Communications Clock -- CLKSW defaults to 0, which selects the alternate BDC clock source. 0 Alternate BDC clock source 1 MCU bus clock MC9S08DZ60 Series Data Sheet, Rev. 4 362 Freescale Semiconductor Chapter 17 Development Support Table 17-2. BDCSCR Register Field Descriptions (continued) Field Description 2 WS Wait or Stop Status -- When the target CPU is in wait or stop mode, most BDC commands cannot function. However, the BACKGROUND command can be used to force the target CPU out of wait or stop and into active background mode where all BDC commands work. Whenever the host forces the target MCU into active background mode, the host should issue a READ_STATUS command to check that BDMACT = 1 before attempting other BDC commands. 0 Target CPU is running user application code or in active background mode (was not in wait or stop mode when background became active) 1 Target CPU is in wait or stop mode, or a BACKGROUND command was used to change from wait or stop to active background mode 1 WSF Wait or Stop Failure Status -- This status bit is set if a memory access command failed due to the target CPU executing a wait or stop instruction at or about the same time. The usual recovery strategy is to issue a BACKGROUND command to get out of wait or stop mode into active background mode, repeat the command that failed, then return to the user program. (Typically, the host would restore CPU registers and stack values and re-execute the wait or stop instruction.) 0 Memory access did not conflict with a wait or stop instruction 1 Memory access command failed because the CPU entered wait or stop mode 0 DVF Data Valid Failure Status -- This status bit is not used in the MC9S08DZ60 Series because it does not have any slow access memory. 0 Memory access did not conflict with a slow memory access 1 Memory access command failed because CPU was not finished with a slow memory access 17.4.1.2 BDC Breakpoint Match Register (BDCBKPT) This 16-bit register holds the address for the hardware breakpoint in the BDC. The BKPTEN and FTS control bits in BDCSCR are used to enable and configure the breakpoint logic. Dedicated serial BDC commands (READ_BKPT and WRITE_BKPT) are used to read and write the BDCBKPT register but is not accessible to user programs because it is not located in the normal memory map of the MCU. Breakpoints are normally set while the target MCU is in active background mode before running the user application program. For additional information about setup and use of the hardware breakpoint logic in the BDC, refer to Section 17.2.4, "BDC Hardware Breakpoint." 17.4.2 System Background Debug Force Reset Register (SBDFR) This register contains a single write-only control bit. A serial background mode command such as WRITE_BYTE must be used to write to SBDFR. Attempts to write this register from a user program are ignored. Reads always return 0x00. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 363 Chapter 17 Development Support R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 BDFR1 W Reset 0 0 0 0 0 0 0 0 = Unimplemented or Reserved 1 BDFR is writable only through serial background mode debug commands, not from user programs. Figure 17-6. System Background Debug Force Reset Register (SBDFR) Table 17-3. SBDFR Register Field Description Field Description 0 BDFR Background Debug Force Reset -- A serial active background mode command such as WRITE_BYTE allows an external debug host to force a target system reset. Writing 1 to this bit forces an MCU reset. This bit cannot be written from a user program. 17.4.3 DBG Registers and Control Bits The debug module includes nine bytes of register space for three 16-bit registers and three 8-bit control and status registers. These registers are located in the high register space of the normal memory map so they are accessible to normal application programs. These registers are rarely if ever accessed by normal user application programs with the possible exception of a ROM patching mechanism that uses the breakpoint logic. 17.4.3.1 Debug Comparator A High Register (DBGCAH) This register contains compare value bits for the high-order eight bits of comparator A. This register is forced to 0x00 at reset and can be read at any time or written at any time unless ARM = 1. 17.4.3.2 Debug Comparator A Low Register (DBGCAL) This register contains compare value bits for the low-order eight bits of comparator A. This register is forced to 0x00 at reset and can be read at any time or written at any time unless ARM = 1. 17.4.3.3 Debug Comparator B High Register (DBGCBH) This register contains compare value bits for the high-order eight bits of comparator B. This register is forced to 0x00 at reset and can be read at any time or written at any time unless ARM = 1. 17.4.3.4 Debug Comparator B Low Register (DBGCBL) This register contains compare value bits for the low-order eight bits of comparator B. This register is forced to 0x00 at reset and can be read at any time or written at any time unless ARM = 1. MC9S08DZ60 Series Data Sheet, Rev. 4 364 Freescale Semiconductor Chapter 17 Development Support 17.4.3.5 Debug FIFO High Register (DBGFH) This register provides read-only access to the high-order eight bits of the FIFO. Writes to this register have no meaning or effect. In the event-only trigger modes, the FIFO only stores data into the low-order byte of each FIFO word, so this register is not used and will read 0x00. Reading DBGFH does not cause the FIFO to shift to the next word. When reading 16-bit words out of the FIFO, read DBGFH before reading DBGFL because reading DBGFL causes the FIFO to advance to the next word of information. 17.4.3.6 Debug FIFO Low Register (DBGFL) This register provides read-only access to the low-order eight bits of the FIFO. Writes to this register have no meaning or effect. Reading DBGFL causes the FIFO to shift to the next available word of information. When the debug module is operating in event-only modes, only 8-bit data is stored into the FIFO (high-order half of each FIFO word is unused). When reading 8-bit words out of the FIFO, simply read DBGFL repeatedly to get successive bytes of data from the FIFO. It isn't necessary to read DBGFH in this case. Do not attempt to read data from the FIFO while it is still armed (after arming but before the FIFO is filled or ARMF is cleared) because the FIFO is prevented from advancing during reads of DBGFL. This can interfere with normal sequencing of reads from the FIFO. Reading DBGFL while the debugger is not armed causes the address of the most-recently fetched opcode to be stored to the last location in the FIFO. By reading DBGFH then DBGFL periodically, external host software can develop a profile of program execution. After eight reads from the FIFO, the ninth read will return the information that was stored as a result of the first read. To use the profiling feature, read the FIFO eight times without using the data to prime the sequence and then begin using the data to get a delayed picture of what addresses were being executed. The information stored into the FIFO on reads of DBGFL (while the FIFO is not armed) is the address of the most-recently fetched opcode. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 365 Chapter 17 Development Support 17.4.3.7 Debug Control Register (DBGC) This register can be read or written at any time. 7 6 5 4 3 2 1 0 DBGEN ARM TAG BRKEN RWA RWAEN RWB RWBEN 0 0 0 0 0 0 0 0 R W Reset Figure 17-7. Debug Control Register (DBGC) Table 17-4. DBGC Register Field Descriptions Field Description 7 DBGEN Debug Module Enable -- Used to enable the debug module. DBGEN cannot be set to 1 if the MCU is secure. 0 DBG disabled 1 DBG enabled 6 ARM Arm Control -- Controls whether the debugger is comparing and storing information in the FIFO. A write is used to set this bit (and ARMF) and completion of a debug run automatically clears it. Any debug run can be manually stopped by writing 0 to ARM or to DBGEN. 0 Debugger not armed 1 Debugger armed 5 TAG Tag/Force Select -- Controls whether break requests to the CPU will be tag or force type requests. If BRKEN = 0, this bit has no meaning or effect. 0 CPU breaks requested as force type requests 1 CPU breaks requested as tag type requests 4 BRKEN Break Enable -- Controls whether a trigger event will generate a break request to the CPU. Trigger events can cause information to be stored in the FIFO without generating a break request to the CPU. For an end trace, CPU break requests are issued to the CPU when the comparator(s) and R/W meet the trigger requirements. For a begin trace, CPU break requests are issued when the FIFO becomes full. TRGSEL does not affect the timing of CPU break requests. 0 CPU break requests not enabled 1 Triggers cause a break request to the CPU 3 RWA R/W Comparison Value for Comparator A -- When RWAEN = 1, this bit determines whether a read or a write access qualifies comparator A. When RWAEN = 0, RWA and the R/W signal do not affect comparator A. 0 Comparator A can only match on a write cycle 1 Comparator A can only match on a read cycle 2 RWAEN Enable R/W for Comparator A -- Controls whether the level of R/W is considered for a comparator A match. 0 R/W is not used in comparison A 1 R/W is used in comparison A 1 RWB R/W Comparison Value for Comparator B -- When RWBEN = 1, this bit determines whether a read or a write access qualifies comparator B. When RWBEN = 0, RWB and the R/W signal do not affect comparator B. 0 Comparator B can match only on a write cycle 1 Comparator B can match only on a read cycle 0 RWBEN Enable R/W for Comparator B -- Controls whether the level of R/W is considered for a comparator B match. 0 R/W is not used in comparison B 1 R/W is used in comparison B MC9S08DZ60 Series Data Sheet, Rev. 4 366 Freescale Semiconductor Chapter 17 Development Support 17.4.3.8 Debug Trigger Register (DBGT) This register can be read any time, but may be written only if ARM = 0, except bits 4 and 5 are hard-wired to 0s. 7 6 TRGSEL BEGIN 0 0 R 5 4 0 0 3 2 1 0 TRG3 TRG2 TRG1 TRG0 0 0 0 0 W Reset 0 0 = Unimplemented or Reserved Figure 17-8. Debug Trigger Register (DBGT) Table 17-5. DBGT Register Field Descriptions Field Description 7 TRGSEL Trigger Type -- Controls whether the match outputs from comparators A and B are qualified with the opcode tracking logic in the debug module. If TRGSEL is set, a match signal from comparator A or B must propagate through the opcode tracking logic and a trigger event is only signalled to the FIFO logic if the opcode at the match address is actually executed. 0 Trigger on access to compare address (force) 1 Trigger if opcode at compare address is executed (tag) 6 BEGIN Begin/End Trigger Select -- Controls whether the FIFO starts filling at a trigger or fills in a circular manner until a trigger ends the capture of information. In event-only trigger modes, this bit is ignored and all debug runs are assumed to be begin traces. 0 Data stored in FIFO until trigger (end trace) 1 Trigger initiates data storage (begin trace) 3:0 TRG[3:0] Select Trigger Mode -- Selects one of nine triggering modes, as described below. 0000 A-only 0001 A OR B 0010 A Then B 0011 Event-only B (store data) 0100 A then event-only B (store data) 0101 A AND B data (full mode) 0110 A AND NOT B data (full mode) 0111 Inside range: A address B 1000 Outside range: address < A or address > B 1001 - 1111 (No trigger) MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 367 Chapter 17 Development Support 17.4.3.9 Debug Status Register (DBGS) This is a read-only status register. R 7 6 5 4 3 2 1 0 AF BF ARMF 0 CNT3 CNT2 CNT1 CNT0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 17-9. Debug Status Register (DBGS) Table 17-6. DBGS Register Field Descriptions Field Description 7 AF Trigger Match A Flag -- AF is cleared at the start of a debug run and indicates whether a trigger match A condition was met since arming. 0 Comparator A has not matched 1 Comparator A match 6 BF Trigger Match B Flag -- BF is cleared at the start of a debug run and indicates whether a trigger match B condition was met since arming. 0 Comparator B has not matched 1 Comparator B match 5 ARMF Arm Flag -- While DBGEN = 1, this status bit is a read-only image of ARM in DBGC. This bit is set by writing 1 to the ARM control bit in DBGC (while DBGEN = 1) and is automatically cleared at the end of a debug run. A debug run is completed when the FIFO is full (begin trace) or when a trigger event is detected (end trace). A debug run can also be ended manually by writing 0 to ARM or DBGEN in DBGC. 0 Debugger not armed 1 Debugger armed 3:0 CNT[3:0] FIFO Valid Count -- These bits are cleared at the start of a debug run and indicate the number of words of valid data in the FIFO at the end of a debug run. The value in CNT does not decrement as data is read out of the FIFO. The external debug host is responsible for keeping track of the count as information is read out of the FIFO. 0000 Number of valid words in FIFO = No valid data 0001 Number of valid words in FIFO = 1 0010 Number of valid words in FIFO = 2 0011 Number of valid words in FIFO = 3 0100 Number of valid words in FIFO = 4 0101 Number of valid words in FIFO = 5 0110 Number of valid words in FIFO = 6 0111 Number of valid words in FIFO = 7 1000 Number of valid words in FIFO = 8 MC9S08DZ60 Series Data Sheet, Rev. 4 368 Freescale Semiconductor Appendix A Electrical Characteristics A.1 Introduction This section contains the most accurate electrical and timing information for the MC9S08DZ60 Series of microcontrollers available at the time of publication. A.2 Parameter Classification The electrical parameters shown in this supplement are guaranteed by various methods. To give the customer a better understanding the following classification is used and the parameters are tagged accordingly in the tables where appropriate: Table A-1. Parameter Classifications P Those parameters are guaranteed during production testing on each individual device. C Those parameters are achieved by the design characterization by measuring a statistically relevant sample size across process variations. T Those parameters are achieved by design characterization on a small sample size from typical devices under typical conditions unless otherwise noted. All values shown in the typical column are within this category. D Those parameters are derived mainly from simulations. NOTE The classification is shown in the column labeled "C" in the parameter tables where appropriate. A.3 Absolute Maximum Ratings Absolute maximum ratings are stress ratings only, and functional operation at the maxima is not guaranteed. Stress beyond the limits specified in Table A-2 may affect device reliability or cause permanent damage to the device. For functional operating conditions, refer to the remaining tables in this section. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 369 Appendix A Electrical Characteristics This device contains circuitry protecting against damage due to high static voltage or electrical fields; however, it is advised that normal precautions be taken to avoid application of any voltages higher than maximum-rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused inputs are tied to an appropriate logic voltage level (for instance, either VSS or VDD). Table A-2. Absolute Maximum Ratings Num Rating Symbol Value Unit 1 Supply voltage VDD -0.3 to + 5.8 V 2 Input voltage VIn - 0.3 to VDD + 0.3 V 3 Instantaneous maximum current (applies to all port pins)1, 2, 3 ID 25 mA 4 Maximum current into VDD IDD 120 mA 5 Storage temperature Tstg -55 to +150 C Single pin limit 1 Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate resistance values for positive (VDD) and negative (VSS) clamp voltages, then use the larger of the two resistance values. 2 All functional non-supply pins are internally clamped to V SS and VDD. 3 Power supply must maintain regulation within operating V DD range during instantaneous and operating maximum current conditions. If positive injection current (VIn > VDD) is greater than IDD, the injection current may flow out of VDD and could result in external power supply going out of regulation. Ensure external VDD load will shunt current greater than maximum injection current. This will be the greatest risk when the MCU is not consuming power. Examples are: if no system clock is present, or if the clock rate is very low which would reduce overall power consumption. A.4 Thermal Characteristics This section provides information about operating temperature range, power dissipation, and package thermal resistance. Power dissipation on I/O pins is usually small compared to the power dissipation in on-chip logic and it is user-determined rather than being controlled by the MCU design. In order to take PI/O into account in power calculations, determine the difference between actual pin voltage and VSS or VDD and multiply by the pin current for each I/O pin. Except in cases of unusually high pin current (heavy loads), the difference between pin voltage and VSS or VDD will be very small. MC9S08DZ60 Series Data Sheet, Rev. 4 370 Freescale Semiconductor Appendix A Electrical Characteristics Table A-3. Thermal Characteristics Num C 1 D Symbol Value Unit Temp. Code Operating temperature range (packaged) TA -40 to 125 -40 to 105 -40 to 85 C M V C TJ 135 C -- 64-pin LQFP JA 69 C/W 48-pin LQFP JA 75 C/W 32-pin LQFP JA 80 C/W 64-pin LQFP JA 51 C/W 48-pin LQFP JA 51 C/W 32-pin LQFP JA 52 C/W Rating 2 T Maximum Junction Temperature1 3 D Thermal resistance2 Single-layer board Four-Layer board 1 Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance. 2 Junction to Ambient Natural Convection The average chip-junction temperature (TJ) in C can be obtained from: TJ = TA + (PD x JA) Eqn. A-1 where: TA = Ambient temperature, C JA = Package thermal resistance, junction-to-ambient, C/W PD = Pint + PI/O Pint = IDD x VDD, Watts -- chip internal power PI/O = Power dissipation on input and output pins -- user determined For most applications, PI/O << Pint and can be neglected. An approximate relationship between PD and TJ (if PI/O is neglected) is: PD = K / (TJ + 273C) Eqn. A-2 Solving equations 1 and 2 for K gives: K = PD x (TA + 273C) + JA x (PD)2 Eqn. A-3 MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 371 Appendix A Electrical Characteristics where K is a constant pertaining to the particular part. K can be determined from equation 3 by measuring PD (at equilibrium) for a known TA. Using this value of K, the values of PD and TJ can be obtained by solving equations 1 and 2 iteratively for any value of TA. A.5 ESD Protection and Latch-Up Immunity Although damage from electrostatic discharge (ESD) is much less common on these devices than on early CMOS circuits, normal handling precautions should be used to avoid exposure to static discharge. Qualification tests are performed to ensure that these devices can withstand exposure to reasonable levels of static without suffering any permanent damage. All ESD testing is in conformity with AEC-Q100 Stress Test Qualification for Automotive Grade Integrated Circuits. During the device qualification ESD stresses were performed for the Human Body Model (HBM) and the Charge Device Model (CDM). A device is defined as a failure if after exposure to ESD pulses the device no longer meets the device specification. Complete DC parametric and functional testing is performed per the applicable device specification at room temperature followed by hot temperature, unless specified otherwise in the device specification. Table A-4. ESD and Latch-up Test Conditions Model Human Body Description Symbol Value Unit Series Resistance R1 1500 Storage Capacitance C 100 pF Number of Pulse per pin - 3 Minimum input voltage limit -2.5 V Maximum input voltage limit 7.5 V Latch-up Table A-5. ESD and Latch-Up Protection Characteristics Num Rating Symbol Min Max Unit 1 Human Body Model (HBM) VHBM +/- 2000 - V 2 Charge Device Model (CDM) VCDM +/- 500 - V 3 Latch-up Current at TA = 125C ILAT +/- 100 - mA MC9S08DZ60 Series Data Sheet, Rev. 4 372 Freescale Semiconductor Appendix A Electrical Characteristics A.6 DC Characteristics This section includes information about power supply requirements, I/O pin characteristics, and power supply current in various operating modes. Table A-6. DC Characteristics Num 1 C Typ1 Max Unit 2.7 V -- 5.5 -- -- C 3 V, ILoad = -0.6 mA VDD - 1.5 -- -- C Output high C voltage 5 V, ILoad = -0.4 mA VDD - 0.8 -- -- 3 V, ILoad = -0.24 mA VDD - 0.8 5 V, ILoad = -10 mA VDD - 1.5 -- -- -- -- C 3 V, ILoad = -3 mA VDD - 1.5 -- -- C 5 V, ILoad = -2 mA VDD - 0.8 -- -- C 3 V, ILoad = -0.4 mA VDD - 0.8 -- -- VDD All I/O pins, low-drive strength VOH All I/O pins, high-drive strength 5V 0 -- -100 3V 0 -- -60 5 V, ILoad = 2 mA -- -- 1.5 C 3 V, ILoad = 0.6 mA -- -- 1.5 C Output low C voltage 5 V, ILoad = 0.4 mA -- -- 0.8 3 V, ILoad = 0.24 mA -- -- 0.8 C Output high current Max total IOH for all ports IOHT All I/O pins, low-drive strength VOL 5 V, ILoad = 10 mA -- -- 1.5 C 3 V, ILoad = 3 mA -- -- 1.5 C 5 V, ILoad = 2 mA -- -- 0.8 C 3 V, ILoad = 0.4 mA -- -- 0.8 P 5 Min VDD - 1.5 P 4 Condition 5 V, ILoad = -2 mA P 3 Symbol -- Operating Voltage P 2 Characteristic All I/O pins, high-drive strength C Output low current Max total IOL for all ports IOLT 5V 0 -- 100 3V 0 -- 60 6 C Input high voltage; all digital inputs VIH 5V 0.65 x VDD -- -- 7 C Input low voltage; all digital inputs VIL 5V -- -- 0.35 x VDD 8 C Input hysteresis Vhys 9 Input leakage P current (Per pin) all input only pins 10 11 P P Hi-Z (off-state) leakage current (per pin) all input/output Pullup resistors (or Pulldown2 resistors when enabled) 0.06 x VDD V mA V mA V mV |IIn| VIn = VDD or VSS -- 0.1 1 A |IOZ| VIn = VDD or VSS -- 0.1 1 A RPU, RPD 5V 20 45 65 C k 3V 20 45 65 Input Capacitance, all pins 12 T 13 D RAM retention voltage CIn -- -- 8 pF VRAM -- 0.6 1.0 V MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 373 Appendix A Electrical Characteristics Table A-6. DC Characteristics (continued) Num 14 C Min Typ1 Max Unit VPOR 0.9 1.4 2.0 V tPOR 10 -- -- s 3.9 4.0 4.0 4.1 4.1 4.2 V 2.48 2.54 2.56 2.62 2.64 2.70 V 4.5 4.6 4.6 4.7 4.7 4.8 V 4.2 4.3 4.3 4.4 4.4 4.5 V 2.84 2.90 2.92 2.98 3.00 3.06 V 2.66 2.72 2.74 2.80 2.82 2.88 V 5V -- 100 -- 3V -- 60 -- VIN > VDD 0 -- 2 VIN < VSS 0 -- -0.2 VIN > VDD 0 -- 25 VIN < VSS 0 -- -5 1.19 1.20 1.21 Characteristic Symbol 3 D POR re-arm voltage 4 15 D POR re-arm time 16 Low-voltage detection threshold -- high range P VDD falling VDD rising 17 Low-voltage detection threshold -- low range P VDD falling VDD rising 18 Low-voltage warning threshold -- high range 1 C VDD falling VDD rising 19 Low-voltage warning threshold -- high range 0 P VDD falling VDD rising 20 Low-voltage warning threshold low range 1 P VDD falling VDD rising 21 Low-voltage warning threshold -- low range 0 C VDD falling VDD rising 22 Low-voltage inhibit reset/recover T hysteresis Condition VLVD1 VLVD0 VLVW3 VLVW2 VLVW1 VLVW0 Vhys mV dc injection current 5, 6, 7, 8 Single pin limit 23 D IIC Total MCU limit, includes sum of all stressed pins 24 1 2 3 4 5 6 Bandgap Voltage Reference C Factory trimmed at VDD = 5.0 V, Temp = 25C mA VBG V Typical values are measured at 25C. Characterized, not tested When a pin interrupt is configured to detect rising edges, pulldown resistors are used in place of pullup resistors. Maximum is highest voltage that POR is guaranteed. Simulated, not tested Power supply must maintain regulation within operating VDD range during instantaneous and operating maximum current conditions. If positive injection current (VIn > VDD) is greater than IDD, the injection current may flow out of VDD and could result in external power supply going out of regulation. Ensure external VDD load will shunt current greater than maximum injection current. This will be the greatest risk when the MCU is not consuming power. Examples are: if no system clock is present, or if clock rate is very low which (would reduce overall power consumption). All functional non-supply pins are internally clamped to VSS and VDD. MC9S08DZ60 Series Data Sheet, Rev. 4 374 Freescale Semiconductor Appendix A Electrical Characteristics 7 Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate resistance values for positive and negative clamp voltages, then use the larger of the two values. 8 PTE1 does not have a clamp diode to VDD. Do not drive PTE1 above VDD. A.7 Supply Current Characteristics Table A-7. Supply Current Characteristics Num C C 1 C P 2 C P 3 C P4 4 Run supply current3 measured at (CPU clock = 2 MHz, fBus = 1 MHz) Symbol RIDD 3 Run supply current measured at (CPU clock = 16 MHz, fBus = 8 MHz) RIDD Run supply current3 measured at (CPU clock = 40 MHz, fBus = 20 MHz) RIDD Stop3 mode supply current VDD (V) Typical1 Max2 5 3 7.5 3 2.8 7.4 5 7.7 11.4 3 7.4 11.2 5 15 24 3 14 23 0.9 -- 1.0 -- 26 39 62 90 0.8 -- 0.9 -- mA mA -40 C (C, V, & M suffix) 25 C (All parts) P 105 C (V suffix only) P 125 C (M suffix only) C -40 C (C, V, & M suffix) C 25 C (All parts) C 105 C (V suffix only) 21 32 C 125 C (M suffix only) 52 80 -40 C (C, V, & M suffix) 0.8 -- 0.9 -- 25 37 46 70 0.7 -- 0.8 -- Stop2 mode supply current Unit mA P4 P4 5 Parameter 5 S3IDD 3 P4 25 C (All parts) P 105 C (V suffix only) P 125 C (M suffix only) C -40 C (C, V, & M suffix) C 25 C (All parts) C 105 C (V suffix only) 20 30 C 125 C (M suffix only) 40 60 5 S2IDD 3 A A MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 375 Appendix A Electrical Characteristics Table A-7. Supply Current Characteristics (continued) Num C 6 C Parameter Symbol VDD (V) Typical1 Max2 Unit 5 300 -- nA 3 300 -- nA 5 110 -- A 3 90 -- A 5 5 -- A 3 5 -- A RTC adder to stop2 or stop35, 25C LVD adder to stop3 (LVDE = LVDSE = 1) 7 C 8 1 2 3 4 5 6 A.8 C Adder to stop3 for oscillator enabled6 (IRCLKEN = 1 and IREFSTEN = 1 or ERCLKEN = 1 and EREFSTEN = 1) Typicals are measured at 25C, unless otherwise noted. Maximum values in this column apply for the full operating temperature range of the device unless otherwise noted. All modules except ADC active, MCG configured for FBE, and does not include any dc loads on port pins Stop currents are tested in production for 25C on all parts. Tests at other temperatures depend upon the part number suffix and maturity of the product. Freescale may eliminate a test insertion at a particular temperature from the production test flow once sufficient data has been collected and is approved. Most customers are expected to find that auto-wakeup from stop2 or stop3 can be used instead of the higher current wait mode. Values given under the following conditions: low range operation (RANGE = 0), low power mode (HGO = 0). Analog Comparator (ACMP) Electricals Table A-8. Analog Comparator Electrical Specifications Num C Symbol Min Typical Max Unit 1 -- Supply voltage VDD 2.7 -- 5.5 V 2 D Supply current (active) IDDAC -- 20 35 A 3 D Analog input voltage VAIN VSS - 0.3 -- VDD V 4 D Analog input offset voltage VAIO 20 40 mV 5 D Analog Comparator hysteresis 6 D 7 D A.9 Rating VH 3.0 6.0 20.0 mV Analog input leakage current IALKG -- -- 1.0 A Analog Comparator initialization delay tAINIT -- -- 1.0 s ADC Characteristics Table A-9. 12-bit ADC Operating Conditions Characteristic Supply voltage Ground voltage Symb Min Typ1 Max Unit Absolute VDDAD 2.7 -- 5.5 V Delta to VDD (VDD-VDDAD)2 VDDAD -100 0 +100 mV Delta to VSS (VSS-VSSAD)2 VSSAD -100 0 +100 mV Conditions Comment MC9S08DZ60 Series Data Sheet, Rev. 4 376 Freescale Semiconductor Appendix A Electrical Characteristics Table A-9. 12-bit ADC Operating Conditions (continued) Symb Min Typ1 Max Unit Comment Ref Voltage High VREFH 2.7 VDDAD VDDAD V Applicable in only 64-pin packages {VREFH < VDDAD characterized but not production test} Ref Voltage Low VREFL VSSAD VSSAD VSSAD V Not Applicable in 64-pin packages (only 32- and 48-pin packages) Input Voltage VADIN VREFL -- VREFH V Input Capacitance CADIN -- 4.5 5.5 pF Input Resistance RADIN -- 3 5 k -- -- -- -- 2 5 10 bit mode fADCK > 4MHz fADCK < 4MHz -- -- -- -- 5 10 8 bit mode (all valid fADCK) -- -- 10 0.4 -- 8.0 0.4 -- 4.0 Characteristic Analog Source Resistance ADC Conversion Clock Freq. Conditions 12 bit mode fADCK > 4MHz fADCK < 4MHz k RAS High Speed (ADLPC=0) Low Power (ADLPC=1) fADCK External to MCU MHz 1 Typical values assume VDDAD = 5.0V, Temp = 25C, fADCK=1.0MHz unless otherwise stated. Typical values are for reference only and are not tested in production. 2 DC potential difference. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 377 Appendix A Electrical Characteristics SIMPLIFIED INPUT PIN EQUIVALENT CIRCUIT ZADIN SIMPLIFIED CHANNEL SELECT CIRCUIT Pad leakage due to input protection ZAS RAS ADC SAR ENGINE RADIN + VADIN VAS - CAS + - RADIN INPUT PIN RADIN INPUT PIN RADIN INPUT PIN CADIN Figure A-1. ADC Input Impedance Equivalency Diagram Table A-10. 12-bit ADC Characteristics (VREFH = VDDAD, VREFL = VSSAD) Characteristic Conditions C Symb Min Typ1 Max Unit Comment Supply Current ADLPC=1 ADLSMP=1 ADCO=1 T IDD + IDDAD -- 133 -- A ADC current only Supply Current ADLPC=1 ADLSMP=0 ADCO=1 T IDD + IDDAD -- 218 -- A ADC current only Supply Current ADLPC=0 ADLSMP=1 ADCO=1 T IDD + IDDAD -- 327 -- A ADC current only Supply Current ADLPC=0 ADLSMP=0 ADCO=1 D IDD + IDDAD -- 0.582 1 mA ADC current only Supply Current Stop, Reset, Module Off IDD + IDDAD -- 0.011 1 A ADC current only ADC Asynchronous Clock Source High Speed (ADLPC=0) fADACK 2 3.3 5 MHz 1.25 2 3.3 tADACK = 1/fADACK Low Power (ADLPC=1) P MC9S08DZ60 Series Data Sheet, Rev. 4 378 Freescale Semiconductor Appendix A Electrical Characteristics Table A-10. 12-bit ADC Characteristics (VREFH = VDDAD, VREFL = VSSAD) (continued) Characteristic Conditions C Symb Min Typ1 Max Unit Comment Conversion Time (Including sample time) Short Sample (ADLSMP=0) D tADC -- 20 -- -- 40 -- ADCK cycles Sample Time Short Sample (ADLSMP=0) -- 3.5 -- See Table 10-13 for conversion time variances -- 23.5 -- -- 3.0 10 Long Sample (ADLSMP=1) D tADS Long Sample (ADLSMP=1) Total Unadjusted Error Differential Non-Linearity Integral Non-Linearity Zero-Scale Error Full-Scale Error Quantization Error Input Leakage Error 12 bit mode T 10 bit mode P -- 1 2.5 8 bit mode T -- 0.5 1.0 12 bit mode T -- 1.75 4.0 10 bit mode3 P -- 0.5 1.0 8 bit mode3 T -- 0.3 0.5 12 bit mode T -- 1.5 4.0 10 bit mode T -- 0.5 1.0 8 bit mode T -- 0.3 0.5 12 bit mode T -- 1.5 6.0 10 bit mode P -- 0.5 1.5 8 bit mode T -- 0.5 0.5 12 bit mode T -- 1 4.0 10 bit mode T -- 0.5 1 8 bit mode T -- 0.5 0.5 12 bit mode D -- -1 to 0 -1 to 0 10 bit mode -- -- 0.5 8 bit mode -- -- 0.5 -- 1 10.0 10 bit mode -- 0.2 2.5 8 bit mode -- 0.1 1 -- 3.266 -- -- 3.638 -- -- 1.396 -- 12 bit mode Temp Sensor Slope -40C- 25C Temp Sensor Voltage 25C D D ETUE DNL INL EZS EFS EQ EIL m 25C- 125C D VTEMP25 ADCK cycles LSB2 Includes quantization LSB2 LSB2 LSB2 VADIN = VSSAD LSB2 VADIN = VDDAD LSB2 LSB2 Pad leakage4 * RAS mV/C V 1 Typical values assume VDDAD = 5.0V, Temp = 25C, fADCK=1.0MHz unless otherwise stated. Typical values are for reference only and are not tested in production. 2 1 LSB = (V N REFH - VREFL)/2 MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 379 Appendix A Electrical Characteristics 3 4 Monotonicity and No-Missing-Codes guaranteed in 10 bit and 8 bit modes Based on input pad leakage current. Refer to pad electricals. A.10 External Oscillator (XOSC) Characteristics Table A-11. Oscillator Electrical Specifications (Temperature Range = -40 to 125C Ambient) Num C Rating Symbol Min Typ1 Max Unit Oscillator crystal or resonator (EREFS = 1, ERCLKEN = 1 Low range (RANGE = 0) C 1 flo 32 -- 38.4 kHz High range (RANGE = 1) FEE or FBE mode 2 fhi-fll 1 -- 5 MHz High range (RANGE = 1) PEE or PBE mode 3 fhi-pll 1 -- 16 MHz High range (RANGE = 1, HGO = 1) BLPE mode fhi-hgo 1 -- 16 MHz High range (RANGE = 1, HGO = 0) BLPE mode fhi-lp 1 -- 8 MHz 2 -- Load capacitors 3 -- C1 C2 See crystal or resonator manufacturer's recommendation. Feedback resistor Low range (32 kHz to 100 kHz) RF High range (1 MHz to 16 MHz) -- 10 -- M -- 1 -- M -- 0 -- Series resistor Low range, low gain (RANGE = 0, HGO = 0) Low range, high gain (RANGE = 0, HGO = 1) 4 -- -- 100 -- -- 0 -- 8 MHz -- 0 0 4 MHz -- 0 10 1 MHz -- 0 20 t CSTL-LP -- 200 -- CSTL-HGO -- 400 -- t CSTH-LP -- 5 -- CSTH-HGO -- 15 -- 0.03125 -- 5 1 -- 16 0 -- 40 High range, low gain (RANGE = 1, HGO = 0) High range, high gain (RANGE = 1, HGO = 1) Crystal start-up time RS 4 Low range, low gain (RANGE = 0, HGO = 0) 5 T k Low range, high gain (RANGE = 0, HGO = 1) t High range, low gain (RANGE = 1, HGO = 0)5 High range, high gain (RANGE = 1, HGO = 1)4 t ms Square wave input clock frequency (EREFS = 0, ERCLKEN = 1) 6 T FEE or FBE mode 2 3 PEE or PBE mode fextal BLPE mode MHz 1 Typical data was characterized at 3.0 V, 25C or is recommended value. When MCG is configured for FEE or FBE mode, the input clock source must be divisible using RDIV to within the range of 31.25 kHz to 39.0625 kHz. 3 When MCG is configured for PEE or PBE mode, input clock source must be divisible using RDIV to within the range of 1 MHz to 2 MHz. 4 This parameter is characterized and not tested on each device. Proper PC board layout procedures must be followed to achieve specifications. This data will vary based upon the crystal manufacturer and board design. The crystal should be characterized by the crystal manufacturer. 5 4 MHz crystal. 2 MC9S08DZ60 Series Data Sheet, Rev. 4 380 Freescale Semiconductor Appendix A Electrical Characteristics MCU EXTAL XTAL RS RF C1 A.11 Crystal or Resonator C2 MCG Specifications Table A-12. MCG Frequency Specifications (Temperature Range = -40 to 125C Ambient) Num C Rating Symbol Min Typical Max Unit 1 P Internal reference frequency - factory trimmed at VDD = 5 V and temperature = 25 C fint_ft -- 31.25 -- kHz 2 P Average internal reference frequency untrimmed 1 fint_ut 25 32.7 41.66 kHz 3 P Average internal reference frequency - user trimmed fint_t 31.25 -- 39.0625 kHz 4 D Internal reference startup time tirefst -- 60 100 us 1 5 DCO output frequency range - untrimmed -- value provided for reference: fdco_ut = 1024 X fint_ut fdco_ut 25.6 33.48 42.66 MHz 6 P DCO output frequency range - trimmed fdco_t 32 -- 40 MHz 7 C Resolution of trimmed DCO output frequency at fixed voltage and temperature (using FTRIM) fdco_res_t -- 0.1 0.2 %fdco 8 C Resolution of trimmed DCO output frequency at fixed voltage and temperature (not using FTRIM) fdco_res_t -- 0.2 0.4 %fdco 9 P Total deviation of trimmed DCO output frequency over voltage and temperature fdco_t -- + 0.5 -1.0 2 %fdco 10 Total deviation of trimmed DCO output frequency C over fixed voltage and temperature range of 0 - 70 C fdco_t -- 0.5 1 %fdco 11 C FLL acquisition time 2 tfll_acquire -- -- 1 ms 12 D PLL acquisition time 3 tpll_acquire -- -- 1 ms 13 C CJitter -- 0.02 0.2 %fdco 14 D VCO operating frequency fvco 7.0 -- 55.0 MHz 15 D PLL reference frequency range fpll_ref 1.0 -- 2.0 MHz 16 T RMS frequency variation of a single clock cycle measured 2 ms after reference edge.5 fpll_cycjit_2ms -- 0.5904 -- %fpll 17 T Maximum frequency variation averaged over 2 ms window. fpll_maxjit_2ms -- 0.001 -- %fpll Long term Jitter of DCO output clock (averaged over 2ms interval) 4 MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 381 Appendix A Electrical Characteristics Table A-12. MCG Frequency Specifications (Temperature Range = -40 to 125C Ambient) (continued) Num C 1 2 3 4 5 6 7 8 Rating Symbol Min Typical Max Unit 18 T RMS frequency variation of a single clock cycle measured 625 ns after reference edge.6 fpll_cycjit_625ns -- 0.5664 -- %fpll 19 T Maximum frequency variation averaged over 625 ns window. fpll_maxjit_625ns -- 0.113 -- %fpll 20 D Lock entry frequency tolerance 7 Dlock 1.49 -- 2.98 % 21 D Lock exit frequency tolerance 8 Dunl 4.47 -- 5.97 % 22 D Lock time - FLL tfll_lock -- -- tfll_acquire+ 1075(1/fint_t) s 23 D Lock time - PLL tpll_lock -- -- tpll_acquire+ 1075(1/fpll_ref) s 24 Loss of external clock minimum frequency D RANGE = 0 floc_low (3/5) x fint -- -- kHz 25 Loss of external clock minimum frequency D RANGE = 1 floc_high (16/5) x fint -- -- kHz TRIM register at default value (0x80) and FTRIM control bit at default value (0x0). This specification applies to any time the FLL reference source or reference divider is changed, trim value changed or changing from FLL disabled (BLPE, BLPI) to FLL enabled (FEI, FEE, FBE, FBI). If a crystal/resonator is being used as the reference, this specification assumes it is already running. This specification applies to any time the PLL VCO divider or reference divider is changed, or changing from PLL disabled (BLPE, BLPI) to PLL enabled (PBE, PEE). If a crystal/resonator is being used as the reference, this specification assumes it is already running. Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum fBUS. Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise injected into the FLL circuitry via VDD and VSS and variation in crystal oscillator frequency increase the CJitter percentage for a given interval. Jitter measurements are based upon a 40MHz MCGOUT clock frequency. In some specifications, this value is described as "long term accuracy of PLL output clock (averaged over 2 ms)" with symbol "fpll_jitter_2ms." The parameter is unchanged, but the description has been changed for clarification purposes. In some specifications, this value is described as "Jitter of PLL output clock measured over 625 ns" with symbol "fpll_jitter_625ns." The parameter is unchanged, but the description has been changed for clarification purposes. Below Dlock minimum, the MCG is guaranteed to enter lock. Above Dlock maximum, the MCG will not enter lock. But if the MCG is already in lock, then the MCG may stay in lock. Below Dunl minimum, the MCG will not exit lock if already in lock. Above Dunl maximum, the MCG is guaranteed to exit lock. MC9S08DZ60 Series Data Sheet, Rev. 4 382 Freescale Semiconductor Appendix A Electrical Characteristics A.12 AC Characteristics This section describes ac timing characteristics for each peripheral system. A.12.1 Control Timing Table A-13. Control Timing Nu m C 1 D/ P 2 Symbol Min Typical1 Max Unit Bus frequency (tcyc = 1/fBus) fBus dc -- 20 MHz T Internal low-power oscillator period tLPO -- 1500 -- s 3 D External reset pulse width2 textrst 1.5 x tcyc -- ns 4 D Reset low drive3 trstdrv 34 x tcyc -- ns 5 D Active background debug mode latch setup time tMSSU 25 -- ns 6 D Active background debug mode latch hold time tMSH 25 -- ns 7 D IRQ/PIAx/ PIBx/PIDx pulse width Asynchronous path2 Synchronous path3 tILIH, tIHIL 100 1.5 tcyc -- -- ns Port rise and fall time -- Low output drive (PTxDS = 0) (load = 50 pF)4 Slew rate control disabled (PTxSE = 0) Slew rate control enabled (PTxSE = 1) tRise, tFall -- -- 40 75 Port rise and fall time -- High output drive (PTxDS = 1) (load = 50 pF)4 Slew rate control disabled (PTxSE = 0) Slew rate control enabled (PTxSE = 1) tRise, tFall -- -- 11 35 8 T Rating ns ns 1 Typical data was characterized at 5.0 V, 25C unless otherwise stated. This is the shortest pulse that is guaranteed to be recognized as a reset pin request. Shorter pulses are not guaranteed to override reset requests from internal sources. 3 When any reset is initiated, internal circuitry drives the RESET pin low for about 34 cycles of t . After POR reset, the bus cyc clock frequency changes to the untrimmed DCO frequency (freset = (fdco_ut)/4) because TRIM is reset to 0x80 and FTRIM is reset to 0; and there is an extra divide-by-two because BDIV is reset to 0:1. After other resets, trim stays at the pre-reset value. 4 Timing is shown with respect to 20% V DD and 80% VDD levels. Temperature range -40C to 125C. 2 textrst RESET PIN Figure A-2. Reset Timing MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 383 Appendix A Electrical Characteristics BKGD/MS RESET tMSH tMSSU Figure A-3. Active Background Debug Mode Latch Timing tIHIL PIAx/PIBx/PIDx IRQ/PIAx/PIBx/PIDx tILIH Figure A-4. Pin Interrupt Timing A.12.2 Timer/PWM Synchronizer circuits determine the shortest input pulses that can be recognized or the fastest clock that can be used as the optional external source to the timer counter. These synchronizers operate from the current bus rate clock. Table A-14. TPM Input Timing Num C 1 -- 2 Rating Symbol Min Max Unit External clock frequency fTCLK dc fBus/4 MHz -- External clock period tTCLK 4 -- tcyc 3 D External clock high time tclkh 1.5 -- tcyc 4 D External clock low time tclkl 1.5 -- tcyc 5 D Input capture pulse width tICPW 1.5 -- tcyc MC9S08DZ60 Series Data Sheet, Rev. 4 384 Freescale Semiconductor Appendix A Electrical Characteristics tTCLK tclkh TPMxCHn tclkl Figure A-5. Timer External Clock tICPW TPMxCHn TPMxCHn tICPW Figure A-6. Timer Input Capture Pulse A.12.3 MSCAN Table A-15. MSCAN Wake-up Pulse Characteristics Num C Rating Symbol Min Typ Max Unit 1 D MSCAN Wake-up dominant pulse filtered tWUP -- -- 2 s 2 D MSCAN Wake-up dominant pulse pass tWUP 5 -- -- s MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 385 Appendix A Electrical Characteristics A.12.4 SPI Table A-16 and Figure A-7 through Figure A-10 describe the timing requirements for the SPI system. Table A-16. SPI Electrical Characteristic Num1 C 1 D Rating2 Symbol Min Max Unit Master Slave tSCK tSCK 2 4 2048 -- tcyc tcyc Master Slave tLead tLead -- 1/2 1/2 -- tSCK tSCK tLag tLag -- 1/2 1/2 -- tSCK tSCK Cycle time Enable lead time 2 D Enable lag time 3 D Master Slave 4 D Clock (SPSCK) high time Master and Slave tSCKH (1/2 tSCK)- 25 -- ns 5 D Clock (SPSCK) low time Master and Slave tSCKL (1/2 tSCK) - 25 -- ns 6 D Master Slave tSI(M) tSI(S) 30 30 -- -- ns ns 7 D Master Slave tHI(M) tHI(S) 30 30 -- -- ns ns 8 D Access time, slave3 tA 0 40 ns 9 D Disable time, slave4 tdis -- 40 ns 10 D Data setup time (outputs) Master Slave tSO tSO 25 25 -- -- ns ns 11 D Master Slave tHO tHO -10 -10 -- -- ns ns Master Slave fop fop fBus/2048 dc 5 MHz Data setup time (inputs) Data hold time (inputs) Data hold time (outputs) Operating frequency5 12 D fBus/4 1 Refer to Figure A-7 through Figure A-10. All timing is shown with respect to 20% VDD and 70% VDD, unless noted; 100 pF load on all SPI pins. All timing assumes slew rate control disabled and high drive strength enabled for SPI output pins. 3 Time to data active from high-impedance state. 4 Hold time to high-impedance state. 5 Maximum baud rate must be limited to 5 MHz due to pad input characteristics. 2 MC9S08DZ60 Series Data Sheet, Rev. 4 386 Freescale Semiconductor Appendix A Electrical Characteristics SS1 (OUTPUT) 1 2 SCK (CPOL = 0) (OUTPUT) 3 5 4 SCK (CPOL = 1) (OUTPUT) 5 4 6 MISO (INPUT) 7 MSB IN2 BIT 6 . . . 1 10 MOSI (OUTPUT) LSB IN 10 MSB OUT2 11 BIT 6 . . . 1 LSB OUT NOTES: 1. SS output mode (MODFEN = 1, SSOE = 1). 2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB. Figure A-7. SPI Master Timing (CPHA = 0) SS(1) (OUTPUT) 1 2 SCK (CPOL = 0) (OUTPUT) 3 5 4 SCK (CPOL = 1) (OUTPUT) 5 4 6 MISO (INPUT) 7 MSB IN(2) 10 MOSI (OUTPUT) BIT 6 . . . 1 LSB IN 11 MSB OUT(2) BIT 6 . . . 1 LSB OUT NOTES: 1. SS output mode (MODFEN = 1, SSOE = 1). 2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB. Figure A-8. SPI Master Timing (CPHA = 1) MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 387 Appendix A Electrical Characteristics SS (INPUT) 3 1 SCK (CPOL = 0) (INPUT) 5 4 2 SCK (CPOL = 1) (INPUT) 5 4 8 MISO (OUTPUT) 11 10 BIT 6 . . . 1 MSB OUT SLAVE SEE NOTE SLAVE LSB OUT 7 6 MOSI (INPUT) 9 BIT 6 . . . 1 MSB IN LSB IN NOTE: 1. Not defined but normally MSB of character just received Figure A-9. SPI Slave Timing (CPHA = 0) SS (INPUT) 1 3 2 SCK (CPOL = 0) (INPUT) 5 4 SCK (CPOL = 1) (INPUT) 5 4 10 MISO (OUTPUT) SEE NOTE 8 MOSI (INPUT) SLAVE 11 MSB OUT 6 BIT 6 . . . 1 9 SLAVE LSB OUT 7 MSB IN BIT 6 . . . 1 LSB IN NOTE: 1. Not defined but normally LSB of character just received Figure A-10. SPI Slave Timing (CPHA = 1) MC9S08DZ60 Series Data Sheet, Rev. 4 388 Freescale Semiconductor Appendix A Electrical Characteristics A.13 Flash and EEPROM This section provides details about program/erase times and program-erase endurance for the Flash and EEPROM memory. Program and erase operations do not require any special power sources other than the normal VDD supply. For more detailed information about program/erase operations, see Chapter 4, "Memory." Table A-17. Flash and EEPROM Characteristics Num C 1 -- 2 Symbol Min Max Unit Supply voltage for program/erase Vprog/erase 2.7 5.5 V -- Supply voltage for read operation 0 < fBus < 8 MHz 0 < fBus < 20 MHz VRead 2.7 5.5 V 3 -- Internal FCLK frequency1 fFCLK 150 200 kHz 4 -- Internal FCLK period (1/FCLK) tFcyc 5 6.67 s 5 -- Byte program time (random location)(2) tprog 9 tFcyc 6 -- Byte program time (burst mode)(2) tBurst 4 tFcyc 7 -- Page erase time2 tPage 4000 tFcyc 8 -- Mass erase time(2) tMass 20,000 tFcyc C Flash Program/erase endurance3 TL to TH = -40C to + 125C T = 25C nFLPE 10 C EEPROM Program/erase endurance3 TL to TH = -40C to + 0C TL to TH = 0C to + 125C T = 25C 11 C Data retention4 9 Rating 10,000 -- Typical -- 100,000 -- -- cycles nEEPE 10,000 50,000 -- -- -- 100,000 -- -- -- cycles tD_ret 15 100 -- years 1 The frequency of this clock is controlled by a software setting. These values are hardware state machine controlled. User code does not need to count cycles. This information supplied for calculating approximate time to program and erase. 3 Typical endurance for Flash and EEPROM is based on the intrinsic bit cell performance. For additional information on how Freescale Semiconductor defines typical endurance, please refer to Engineering Bulletin EB619, Typical Endurance for Nonvolatile Memory. 4 Typical data retention values are based on intrinsic capability of the technology measured at high temperature and de-rated to 25C using the Arrhenius equation. For additional information on how Freescale Semiconductor defines typical data retention, please refer to Engineering Bulletin EB618, Typical Data Retention for Nonvolatile Memory. 2 MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 389 Appendix A Electrical Characteristics A.14 EMC Performance Electromagnetic compatibility (EMC) performance is highly dependant on the environment in which the MCU resides. Board design and layout, circuit topology choices, location and characteristics of external components as well as MCU software operation all play a significant role in EMC performance. The system designer should consult Freescale applications notes such as AN2321, AN1050, AN1263, AN2764, and AN1259 for advice and guidance specifically targeted at optimizing EMC performance. A.14.1 Radiated Emissions Microcontroller radiated RF emissions are measured from 150 kHz to 1 GHz using the TEM/GTEM Cell method in accordance with the IEC 61967-2 and SAE J1752/3 standards. The measurement is performed with the microcontroller installed on a custom EMC evaluation board while running specialized EMC test software. The radiated emissions from the microcontroller are measured in a TEM cell in two package orientations (North and East). For more detailed information concerning the evaluation results, conditions and setup, please refer to the EMC Evaluation Report for this device. The maximum radiated RF emissions of the tested configuration in all orientations are less than or equal to the reported emissions levels. Table A-18. Radiated Emissions for 3M05C Mask Set Parameter Symbol Conditions Frequency VRE_TEM VDD = 5 TA = +25oC 64 LQFP 0.15 - 50 MHz Radiated emissions, electric field -- Conditions - 1 fosc/fCPU 50 - 150 MHz 150 - 500 MHz 500 - 1000 MHz Level1 (Max) Unit 18 dBV 18 16 MHz Crystal 20 MHz Bus 13 7 IEC Level L -- SAE Level 2 -- Data based on qualification test results. MC9S08DZ60 Series Data Sheet, Rev. 4 390 Freescale Semiconductor Appendix B Timer Pulse-Width Modulator (TPMV2) NOTE This chapter refers to S08TPM version 2, which applies to the 3M05C and older mask sets of this device. )M74K and newer mask set devices use S08TPM version 3. If your device uses mask 0M74K or newer, please refer to Chapter 16, "Timer Pulse-Width Modulator (S08TPMV3) for information pertaining to that module. The TPM uses one input/output (I/O) pin per channel, TPMxCHn where x is the TPM number (for example, 1 or 2) and n is the channel number (for example, 0-4). The TPM shares its I/O pins with general-purpose I/O port pins (refer to the Pins and Connections chapter for more information). B.0.1 Features The TPM has the following features: * Each TPM may be configured for buffered, center-aligned pulse-width modulation (CPWM) on all channels * Clock sources independently selectable per TPM (multiple TPMs device) * Selectable clock sources (device dependent): bus clock, fixed system clock, external pin * Clock prescaler taps for divide by 1, 2, 4, 8, 16, 32, 64, or 128 * 16-bit free-running or up/down (CPWM) count operation * 16-bit modulus register to control counter range * Timer system enable * One interrupt per channel plus a terminal count interrupt for each TPM module (multiple TPMs device) * Channel features: -- Each channel may be input capture, output compare, or buffered edge-aligned PWM -- Rising-edge, falling-edge, or any-edge input capture trigger -- Set, clear, or toggle output compare action -- Selectable polarity on PWM outputs B.0.2 Block Diagram Figure B-1 shows the structure of a TPM. Some MCUs include more than one TPM, with various numbers of channels. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 391 Appendix B Timer Pulse-Width Modulator (TPMV2) BUSCLK XCLK TPMxCLK SYNC CLOCK SOURCE SELECT OFF, BUS, XCLK, EXT CLKSB PRESCALE AND SELECT DIVIDE BY 1, 2, 4, 8, 16, 32, 64, or 128 PS2 CLKSA PS1 PS0 CPWMS MAIN 16-BIT COUNTER TOF COUNTER RESET INTERRUPT LOGIC TOIE 16-BIT COMPARATOR TPMxMODH:TPMxMODL CHANNEL 0 ELS0B ELS0A PORT LOGIC 16-BIT COMPARATOR TPMxC0VH:TPMxC0VL CH0F INTERRUPT LOGIC 16-BIT LATCH INTERNAL BUS CHANNEL 1 MS0B MS0A ELS1B ELS1A CH0IE TPMxCH1 PORT LOGIC 16-BIT COMPARATOR CH1F TPMxC1VH:TPMxC1VL INTERRUPT LOGIC 16-BIT LATCH MS1A ELSnB ELSnA ... ... MS1B CH1IE ... CHANNEL n TPMxCH0 TPMxCHn PORT LOGIC 16-BIT COMPARATOR TPMxCnVH:TPMxCnVL CHnF 16-BIT LATCH MSnB MSnA CHnIE INTERRUPT LOGIC Figure B-1. TPM Block Diagram The central component of the TPM is the 16-bit counter that can operate as a free-running counter, a modulo counter, or an up-/down-counter when the TPM is configured for center-aligned PWM. The TPM counter (when operating in normal up-counting mode) provides the timing reference for the input capture, output compare, and edge-aligned PWM functions. The timer counter modulo registers, TPMxMODH:TPMxMODL, control the modulo value of the counter. (The values 0x0000 or 0xFFFF effectively make the counter free running.) Software can read the counter value at any time without affecting the counting sequence. Any write to either byte of the TPMxCNT counter resets the counter regardless of the data value written. MC9S08DZ60 Series Data Sheet, Rev. 4 392 Freescale Semiconductor Appendix B Timer Pulse-Width Modulator (TPMV2) All TPM channels are programmable independently as input capture, output compare, or buffered edge-aligned PWM channels. B.1 External Signal Description When any pin associated with the timer is configured as a timer input, a passive pullup can be enabled. After reset, the TPM modules are disabled and all pins default to general-purpose inputs with the passive pullups disabled. B.1.1 External TPM Clock Sources When control bits CLKSB:CLKSA in the timer status and control register are set to 1:1, the prescaler and consequently the 16-bit counter for TPMx are driven by an external clock source, TPMxCLK, connected to an I/O pin. A synchronizer is needed between the external clock and the rest of the TPM. This synchronizer is clocked by the bus clock so the frequency of the external source must be less than one-half the frequency of the bus rate clock. The upper frequency limit for this external clock source is specified to be one-fourth the bus frequency to conservatively accommodate duty cycle and phase-locked loop (PLL) or frequency-locked loop (FLL) frequency jitter effects. On some devices the external clock input is shared with one of the TPM channels. When a TPM channel is shared as the external clock input, the associated TPM channel cannot use the pin. (The channel can still be used in output compare mode as a software timer.) Also, if one of the TPM channels is used as the external clock input, the corresponding ELSnB:ELSnA control bits must be set to 0:0 so the channel is not trying to use the same pin. B.1.2 TPMxCHn -- TPMx Channel n I/O Pins Each TPM channel is associated with an I/O pin on the MCU. The function of this pin depends on the configuration of the channel. In some cases, no pin function is needed so the pin reverts to being controlled by general-purpose I/O controls. When a timer has control of a port pin, the port data and data direction registers do not affect the related pin(s). See the Pins and Connections chapter for additional information about shared pin functions. B.2 Register Definition The TPM includes: * An 8-bit status and control register (TPMxSC) * A 16-bit counter (TPMxCNTH:TPMxCNTL) * A 16-bit modulo register (TPMxMODH:TPMxMODL) Each timer channel has: * An 8-bit status and control register (TPMxCnSC) * A 16-bit channel value register (TPMxCnVH:TPMxCnVL) Refer to the direct-page register summary in the Memory chapter of this data sheet for the absolute address assignments for all TPM registers. This section refers to registers and control bits only by their names. A MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 393 Appendix B Timer Pulse-Width Modulator (TPMV2) Freescale-provided equate or header file is used to translate these names into the appropriate absolute addresses. B.2.1 Timer Status and Control Register (TPMxSC) TPMxSC contains the overflow status flag and control bits that are used to configure the interrupt enable, TPM configuration, clock source, and prescale divisor. These controls relate to all channels within this timer module. 7 R 6 5 4 3 2 1 0 TOIE CPWMS CLKSB CLKSA PS2 PS1 PS0 0 0 0 0 0 0 0 TOF W Reset 0 = Unimplemented or Reserved Figure B-2. Timer Status and Control Register (TPMxSC) Table B-1. TPMxSC Register Field Descriptions Field Description 7 TOF Timer Overflow Flag -- This flag is set when the TPM counter changes to 0x0000 after reaching the modulo value programmed in the TPM counter modulo registers. When the TPM is configured for CPWM, TOF is set after the counter has reached the value in the modulo register, at the transition to the next lower count value. Clear TOF by reading the TPM status and control register when TOF is set and then writing a 0 to TOF. If another TPM overflow occurs before the clearing sequence is complete, the sequence is reset so TOF would remain set after the clear sequence was completed for the earlier TOF. Reset clears TOF. Writing a 1 to TOF has no effect. 0 TPM counter has not reached modulo value or overflow 1 TPM counter has overflowed 6 TOIE Timer Overflow Interrupt Enable -- This read/write bit enables TPM overflow interrupts. If TOIE is set, an interrupt is generated when TOF equals 1. Reset clears TOIE. 0 TOF interrupts inhibited (use software polling) 1 TOF interrupts enabled 5 CPWMS Center-Aligned PWM Select -- This read/write bit selects CPWM operating mode. Reset clears this bit so the TPM operates in up-counting mode for input capture, output compare, and edge-aligned PWM functions. Setting CPWMS reconfigures the TPM to operate in up-/down-counting mode for CPWM functions. Reset clears CPWMS. 0 All TPMx channels operate as input capture, output compare, or edge-aligned PWM mode as selected by the MSnB:MSnA control bits in each channel's status and control register 1 All TPMx channels operate in center-aligned PWM mode 4:3 CLKS[B:A] Clock Source Select -- As shown in Table B-2, this 2-bit field is used to disable the TPM system or select one of three clock sources to drive the counter prescaler. The external source and the XCLK are synchronized to the bus clock by an on-chip synchronization circuit. 2:0 PS[2:0] Prescale Divisor Select -- This 3-bit field selects one of eight divisors for the TPM clock input as shown in Table B-3. This prescaler is located after any clock source synchronization or clock source selection, so it affects whatever clock source is selected to drive the TPM system. MC9S08DZ60 Series Data Sheet, Rev. 4 394 Freescale Semiconductor Appendix B Timer Pulse-Width Modulator (TPMV2) Table B-2. TPM Clock Source Selection CLKSB:CLKSA TPM Clock Source to Prescaler Input 0:0 No clock selected (TPMx disabled) 0:1 Bus rate clock (BUSCLK) 1:0 Fixed system clock (XCLK) 1:1 External source (TPMxCLK)1,2 1 The maximum frequency that is allowed as an external clock is one-fourth of the bus frequency. 2 If the external clock input is shared with channel n and is selected as the TPM clock source, the corresponding ELSnB:ELSnA control bits should be set to 0:0 so channel n does not try to use the same pin for a conflicting function. Table B-3. Prescale Divisor Selection B.2.2 PS2:PS1:PS0 TPM Clock Source Divided-By 0:0:0 1 0:0:1 2 0:1:0 4 0:1:1 8 1:0:0 16 1:0:1 32 1:1:0 64 1:1:1 128 Timer Counter Registers (TPMxCNTH:TPMxCNTL) The two read-only TPM counter registers contain the high and low bytes of the value in the TPM counter. Reading either byte (TPMxCNTH or TPMxCNTL) latches the contents of both bytes into a buffer where they remain latched until the other byte is read. This allows coherent 16-bit reads in either order. The coherency mechanism is automatically restarted by an MCU reset, a write of any value to TPMxCNTH or TPMxCNTL, or any write to the timer status/control register (TPMxSC). Reset clears the TPM counter registers. R 7 6 5 4 3 2 1 0 Bit 15 14 13 12 11 10 9 Bit 8 0 0 W Reset Any write to TPMxCNTH clears the 16-bit counter. 0 0 0 0 0 0 Figure B-3. Timer Counter Register High (TPMxCNTH) MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 395 Appendix B Timer Pulse-Width Modulator (TPMV2) R 7 6 5 4 3 2 1 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 W Reset Any write to TPMxCNTL clears the 16-bit counter. 0 0 0 0 0 0 Figure B-4. Timer Counter Register Low (TPMxCNTL) When background mode is active, the timer counter and the coherency mechanism are frozen such that the buffer latches remain in the state they were in when the background mode became active even if one or both bytes of the counter are read while background mode is active. B.2.3 Timer Counter Modulo Registers (TPMxMODH:TPMxMODL) The read/write TPM modulo registers contain the modulo value for the TPM counter. After the TPM counter reaches the modulo value, the TPM counter resumes counting from 0x0000 at the next clock (CPWMS = 0) or starts counting down (CPWMS = 1), and the overflow flag (TOF) becomes set. Writing to TPMxMODH or TPMxMODL inhibits TOF and overflow interrupts until the other byte is written. Reset sets the TPM counter modulo registers to 0x0000, which results in a free-running timer counter (modulo disabled). 7 6 5 4 3 2 1 0 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 R W Reset Figure B-5. Timer Counter Modulo Register High (TPMxMODH) 7 6 5 4 3 2 1 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 R W Reset Figure B-6. Timer Counter Modulo Register Low (TPMxMODL) It is good practice to wait for an overflow interrupt so both bytes of the modulo register can be written well before a new overflow. An alternative approach is to reset the TPM counter before writing to the TPM modulo registers to avoid confusion about when the first counter overflow will occur. MC9S08DZ60 Series Data Sheet, Rev. 4 396 Freescale Semiconductor Appendix B Timer Pulse-Width Modulator (TPMV2) B.2.4 Timer Channel n Status and Control Register (TPMxCnSC) TPMxCnSC contains the channel interrupt status flag and control bits that are used to configure the interrupt enable, channel configuration, and pin function. 7 6 5 4 3 2 CHnF CHnIE MSnB MSnA ELSnB ELSnA 0 0 0 0 0 0 R 1 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure B-7. Timer Channel n Status and Control Register (TPMxCnSC) Table B-4. TPMxCnSC Register Field Descriptions Field Description 7 CHnF Channel n Flag -- When channel n is configured for input capture, this flag bit is set when an active edge occurs on the channel n pin. When channel n is an output compare or edge-aligned PWM channel, CHnF is set when the value in the TPM counter registers matches the value in the TPM channel n value registers. This flag is seldom used with center-aligned PWMs because it is set every time the counter matches the channel value register, which correspond to both edges of the active duty cycle period. A corresponding interrupt is requested when CHnF is set and interrupts are enabled (CHnIE = 1). Clear CHnF by reading TPMxCnSC while CHnF is set and then writing a 0 to CHnF. If another interrupt request occurs before the clearing sequence is complete, the sequence is reset so CHnF would remain set after the clear sequence was completed for the earlier CHnF. This is done so a CHnF interrupt request cannot be lost by clearing a previous CHnF. Reset clears CHnF. Writing a 1 to CHnF has no effect. 0 No input capture or output compare event occurred on channel n 1 Input capture or output compare event occurred on channel n 6 CHnIE Channel n Interrupt Enable -- This read/write bit enables interrupts from channel n. Reset clears CHnIE. 0 Channel n interrupt requests disabled (use software polling) 1 Channel n interrupt requests enabled 5 MSnB Mode Select B for TPM Channel n -- When CPWMS = 0, MSnB = 1 configures TPM channel n for edge-aligned PWM mode. For a summary of channel mode and setup controls, refer to Table B-5. 4 MSnA Mode Select A for TPM Channel n -- When CPWMS = 0 and MSnB = 0, MSnA configures TPM channel n for input capture mode or output compare mode. Refer to Table B-5 for a summary of channel mode and setup controls. 3:2 ELSn[B:A] Edge/Level Select Bits -- Depending on the operating mode for the timer channel as set by CPWMS:MSnB:MSnA and shown in Table B-5, these bits select the polarity of the input edge that triggers an input capture event, select the level that will be driven in response to an output compare match, or select the polarity of the PWM output. Setting ELSnB:ELSnA to 0:0 configures the related timer pin as a general-purpose I/O pin unrelated to any timer channel functions. This function is typically used to temporarily disable an input capture channel or to make the timer pin available as a general-purpose I/O pin when the associated timer channel is set up as a software timer that does not require the use of a pin. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 397 Appendix B Timer Pulse-Width Modulator (TPMV2) Table B-5. Mode, Edge, and Level Selection CPWMS MSnB:MSnA ELSnB:ELSnA X XX 00 0 00 01 01 Input capture Capture on falling edge only 11 Capture on rising or falling edge Output compare Software compare only Toggle output on compare 10 Clear output on compare 11 Set output on compare 10 Edge-aligned PWM X1 XX Capture on rising edge only 10 01 1 Configuration Pin not used for TPM channel; use as an external clock for the TPM or revert to general-purpose I/O 00 1X Mode 10 Center-aligned PWM X1 High-true pulses (clear output on compare) Low-true pulses (set output on compare) High-true pulses (clear output on compare-up) Low-true pulses (set output on compare-up) If the associated port pin is not stable for at least two bus clock cycles before changing to input capture mode, it is possible to get an unexpected indication of an edge trigger. Typically, a program would clear status flags after changing channel configuration bits and before enabling channel interrupts or using the status flags to avoid any unexpected behavior. B.2.5 Timer Channel Value Registers (TPMxCnVH:TPMxCnVL) These read/write registers contain the captured TPM counter value of the input capture function or the output compare value for the output compare or PWM functions. The channel value registers are cleared by reset. 7 6 5 4 3 2 1 0 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 R W Reset Figure B-8. Timer Channel Value Register High (TPMxCnVH) 7 6 5 4 3 2 1 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 R W Reset Figure B-9. Timer Channel Value Register Low (TPMxCnVL) MC9S08DZ60 Series Data Sheet, Rev. 4 398 Freescale Semiconductor Appendix B Timer Pulse-Width Modulator (TPMV2) In input capture mode, reading either byte (TPMxCnVH or TPMxCnVL) latches the contents of both bytes into a buffer where they remain latched until the other byte is read. This latching mechanism also resets (becomes unlatched) when the TPMxCnSC register is written. In output compare or PWM modes, writing to either byte (TPMxCnVH or TPMxCnVL) latches the value into a buffer. When both bytes have been written, they are transferred as a coherent 16-bit value into the timer channel value registers. This latching mechanism may be manually reset by writing to the TPMxCnSC register. This latching mechanism allows coherent 16-bit writes in either order, which is friendly to various compiler implementations. B.3 Functional Description All TPM functions are associated with a main 16-bit counter that allows flexible selection of the clock source and prescale divisor. A 16-bit modulo register also is associated with the main 16-bit counter in the TPM. Each TPM channel is optionally associated with an MCU pin and a maskable interrupt function. The TPM has center-aligned PWM capabilities controlled by the CPWMS control bit in TPMxSC. When CPWMS is set to 1, timer counter TPMxCNT changes to an up-/down-counter and all channels in the associated TPM act as center-aligned PWM channels. When CPWMS = 0, each channel can independently be configured to operate in input capture, output compare, or buffered edge-aligned PWM mode. The following sections describe the main 16-bit counter and each of the timer operating modes (input capture, output compare, edge-aligned PWM, and center-aligned PWM). Because details of pin operation and interrupt activity depend on the operating mode, these topics are covered in the associated mode sections. B.3.1 Counter All timer functions are based on the main 16-bit counter (TPMxCNTH:TPMxCNTL). This section discusses selection of the clock source, up-counting vs. up-/down-counting, end-of-count overflow, and manual counter reset. After any MCU reset, CLKSB:CLKSA = 0:0 so no clock source is selected and the TPM is inactive. Normally, CLKSB:CLKSA would be set to 0:1 so the bus clock drives the timer counter. The clock source for the TPM can be selected to be off, the bus clock (BUSCLK), the fixed system clock (XCLK), or an external input. The maximum frequency allowed for the external clock option is one-fourth the bus rate. Refer to Section B.2.1, "Timer Status and Control Register (TPMxSC)" and Table B-2 for more information about clock source selection. When the microcontroller is in active background mode, the TPM temporarily suspends all counting until the microcontroller returns to normal user operating mode. During stop mode, all TPM clocks are stopped; therefore, the TPM is effectively disabled until clocks resume. During wait mode, the TPM continues to operate normally. The main 16-bit counter has two counting modes. When center-aligned PWM is selected (CPWMS = 1), the counter operates in up-/down-counting mode. Otherwise, the counter operates as a simple up-counter. MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 399 Appendix B Timer Pulse-Width Modulator (TPMV2) As an up-counter, the main 16-bit counter counts from 0x0000 through its terminal count and then continues with 0x0000. The terminal count is 0xFFFF or a modulus value in TPMxMODH:TPMxMODL. When center-aligned PWM operation is specified, the counter counts upward from 0x0000 through its terminal count and then counts downward to 0x0000 where it returns to up-counting. Both 0x0000 and the terminal count value (value in TPMxMODH:TPMxMODL) are normal length counts (one timer clock period long). An interrupt flag and enable are associated with the main 16-bit counter. The timer overflow flag (TOF) is a software-accessible indication that the timer counter has overflowed. The enable signal selects between software polling (TOIE = 0) where no hardware interrupt is generated, or interrupt-driven operation (TOIE = 1) where a static hardware interrupt is automatically generated whenever the TOF flag is 1. The conditions that cause TOF to become set depend on the counting mode (up or up/down). In up-counting mode, the main 16-bit counter counts from 0x0000 through 0xFFFF and overflows to 0x0000 on the next counting clock. TOF becomes set at the transition from 0xFFFF to 0x0000. When a modulus limit is set, TOF becomes set at the transition from the value set in the modulus register to 0x0000. When the main 16-bit counter is operating in up-/down-counting mode, the TOF flag gets set as the counter changes direction at the transition from the value set in the modulus register and the next lower count value. This corresponds to the end of a PWM period. (The 0x0000 count value corresponds to the center of a period.) Because the HCS08 MCU is an 8-bit architecture, a coherency mechanism is built into the timer counter for read operations. Whenever either byte of the counter is read (TPMxCNTH or TPMxCNTL), both bytes are captured into a buffer so when the other byte is read, the value will represent the other byte of the count at the time the first byte was read. The counter continues to count normally, but no new value can be read from either byte until both bytes of the old count have been read. The main timer counter can be reset manually at any time by writing any value to either byte of the timer count TPMxCNTH or TPMxCNTL. Resetting the counter in this manner also resets the coherency mechanism in case only one byte of the counter was read before resetting the count. B.3.2 Channel Mode Selection Provided CPWMS = 0 (center-aligned PWM operation is not specified), the MSnB and MSnA control bits in the channel n status and control registers determine the basic mode of operation for the corresponding channel. Choices include input capture, output compare, and buffered edge-aligned PWM. B.3.2.1 Input Capture Mode With the input capture function, the TPM can capture the time at which an external event occurs. When an active edge occurs on the pin of an input capture channel, the TPM latches the contents of the TPM counter into the channel value registers (TPMxCnVH:TPMxCnVL). Rising edges, falling edges, or any edge may be chosen as the active edge that triggers an input capture. When either byte of the 16-bit capture register is read, both bytes are latched into a buffer to support coherent 16-bit accesses regardless of order. The coherency sequence can be manually reset by writing to the channel status/control register (TPMxCnSC). MC9S08DZ60 Series Data Sheet, Rev. 4 400 Freescale Semiconductor Appendix B Timer Pulse-Width Modulator (TPMV2) An input capture event sets a flag bit (CHnF) that can optionally generate a CPU interrupt request. B.3.2.2 Output Compare Mode With the output compare function, the TPM can generate timed pulses with programmable position, polarity, duration, and frequency. When the counter reaches the value in the channel value registers of an output compare channel, the TPM can set, clear, or toggle the channel pin. In output compare mode, values are transferred to the corresponding timer channel value registers only after both 8-bit bytes of a 16-bit register have been written. This coherency sequence can be manually reset by writing to the channel status/control register (TPMxCnSC). An output compare event sets a flag bit (CHnF) that can optionally generate a CPU interrupt request. B.3.2.3 Edge-Aligned PWM Mode This type of PWM output uses the normal up-counting mode of the timer counter (CPWMS = 0) and can be used when other channels in the same TPM are configured for input capture or output compare functions. The period of this PWM signal is determined by the setting in the modulus register (TPMxMODH:TPMxMODL). The duty cycle is determined by the setting in the timer channel value register (TPMxCnVH:TPMxCnVL). The polarity of this PWM signal is determined by the setting in the ELSnA control bit. Duty cycle cases of 0 percent and 100 percent are possible. As Figure B-10 shows, the output compare value in the TPM channel registers determines the pulse width (duty cycle) of the PWM signal. The time between the modulus overflow and the output compare is the pulse width. If ELSnA = 0, the counter overflow forces the PWM signal high and the output compare forces the PWM signal low. If ELSnA = 1, the counter overflow forces the PWM signal low and the output compare forces the PWM signal high. OVERFLOW OVERFLOW OVERFLOW PERIOD PULSE WIDTH TPMxC OUTPUT COMPARE OUTPUT COMPARE OUTPUT COMPARE Figure B-10. PWM Period and Pulse Width (ELSnA = 0) When the channel value register is set to 0x0000, the duty cycle is 0 percent. By setting the timer channel value register (TPMxCnVH:TPMxCnVL) to a value greater than the modulus setting, 100% duty cycle can be achieved. This implies that the modulus setting must be less than 0xFFFF to get 100% duty cycle. Because the HCS08 is a family of 8-bit MCUs, the settings in the timer channel registers are buffered to ensure coherent 16-bit updates and to avoid unexpected PWM pulse widths. Writes to either register, TPMxCnVH or TPMxCnVL, write to buffer registers. In edge-PWM mode, values are transferred to the corresponding timer channel registers only after both 8-bit bytes of a 16-bit register have been written and MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 401 Appendix B Timer Pulse-Width Modulator (TPMV2) the value in the TPMxCNTH:TPMxCNTL counter is 0x0000. (The new duty cycle does not take effect until the next full period.) B.3.3 Center-Aligned PWM Mode This type of PWM output uses the up-/down-counting mode of the timer counter (CPWMS = 1). The output compare value in TPMxCnVH:TPMxCnVL determines the pulse width (duty cycle) of the PWM signal and the period is determined by the value in TPMxMODH:TPMxMODL. TPMxMODH:TPMxMODL should be kept in the range of 0x0001 to 0x7FFF because values outside this range can produce ambiguous results. ELSnA will determine the polarity of the CPWM output. pulse width = 2 x (TPMxCnVH:TPMxCnVL) Eqn. 17-1 period = 2 x (TPMxMODH:TPMxMODL); for TPMxMODH:TPMxMODL = 0x0001-0x7FFF Eqn. 17-2 If the channel value register TPMxCnVH:TPMxCnVL is zero or negative (bit 15 set), the duty cycle will be 0%. If TPMxCnVH:TPMxCnVL is a positive value (bit 15 clear) and is greater than the (nonzero) modulus setting, the duty cycle will be 100% because the duty cycle compare will never occur. This implies the usable range of periods set by the modulus register is 0x0001 through 0x7FFE (0x7FFF if generation of 100% duty cycle is not necessary). This is not a significant limitation because the resulting period is much longer than required for normal applications. TPMxMODH:TPMxMODL = 0x0000 is a special case that should not be used with center-aligned PWM mode. When CPWMS = 0, this case corresponds to the counter running free from 0x0000 through 0xFFFF, but when CPWMS = 1 the counter needs a valid match to the modulus register somewhere other than at 0x0000 in order to change directions from up-counting to down-counting. Figure B-11 shows the output compare value in the TPM channel registers (multiplied by 2), which determines the pulse width (duty cycle) of the CPWM signal. If ELSnA = 0, the compare match while counting up forces the CPWM output signal low and a compare match while counting down forces the output high. The counter counts up until it reaches the modulo setting in TPMxMODH:TPMxMODL, then counts down until it reaches zero. This sets the period equal to two times TPMxMODH:TPMxMODL. COUNT = 0 COUNT = TPMxMODH:TPMx OUTPUT COMPARE (COUNT UP) OUTPUT COMPARE (COUNT DOWN) COUNT = TPMxMODH:TPMx TPM1C PULSE WIDTH 2x 2x PERIOD Figure B-11. CPWM Period and Pulse Width (ELSnA = 0) Center-aligned PWM outputs typically produce less noise than edge-aligned PWMs because fewer I/O pin transitions are lined up at the same system clock edge. This type of PWM is also required for some types of motor drives. MC9S08DZ60 Series Data Sheet, Rev. 4 402 Freescale Semiconductor Appendix B Timer Pulse-Width Modulator (TPMV2) Because the HCS08 is a family of 8-bit MCUs, the settings in the timer channel registers are buffered to ensure coherent 16-bit updates and to avoid unexpected PWM pulse widths. Writes to any of the registers, TPMxMODH, TPMxMODL, TPMxCnVH, and TPMxCnVL, actually write to buffer registers. Values are transferred to the corresponding timer channel registers only after both 8-bit bytes of a 16-bit register have been written and the timer counter overflows (reverses direction from up-counting to down-counting at the end of the terminal count in the modulus register). This TPMxCNT overflow requirement only applies to PWM channels, not output compares. Optionally, when TPMxCNTH:TPMxCNTL = TPMxMODH:TPMxMODL, the TPM can generate a TOF interrupt at the end of this count. The user can choose to reload any number of the PWM buffers, and they will all update simultaneously at the start of a new period. Writing to TPMxSC cancels any values written to TPMxMODH and/or TPMxMODL and resets the coherency mechanism for the modulo registers. Writing to TPMxCnSC cancels any values written to the channel value registers and resets the coherency mechanism for TPMxCnVH:TPMxCnVL. B.4 TPM Interrupts The TPM generates an optional interrupt for the main counter overflow and an interrupt for each channel. The meaning of channel interrupts depends on the mode of operation for each channel. If the channel is configured for input capture, the interrupt flag is set each time the selected input capture edge is recognized. If the channel is configured for output compare or PWM modes, the interrupt flag is set each time the main timer counter matches the value in the 16-bit channel value register. See the Resets, Interrupts, and System Configuration chapter for absolute interrupt vector addresses, priority, and local interrupt mask control bits. For each interrupt source in the TPM, a flag bit is set on recognition of the interrupt condition such as timer overflow, channel input capture, or output compare events. This flag may be read (polled) by software to verify that the action has occurred, or an associated enable bit (TOIE or CHnIE) can be set to enable hardware interrupt generation. While the interrupt enable bit is set, a static interrupt will be generated whenever the associated interrupt flag equals 1. It is the responsibility of user software to perform a sequence of steps to clear the interrupt flag before returning from the interrupt service routine. B.4.1 Clearing Timer Interrupt Flags TPM interrupt flags are cleared by a 2-step process that includes a read of the flag bit while it is set (1) followed by a write of 0 to the bit. If a new event is detected between these two steps, the sequence is reset and the interrupt flag remains set after the second step to avoid the possibility of missing the new event. B.4.2 Timer Overflow Interrupt Description The conditions that cause TOF to become set depend on the counting mode (up or up/down). In up-counting mode, the 16-bit timer counter counts from 0x0000 through 0xFFFF and overflows to 0x0000 on the next counting clock. TOF becomes set at the transition from 0xFFFF to 0x0000. When a modulus limit is set, TOF becomes set at the transition from the value set in the modulus register to 0x0000. When the counter is operating in up-/down-counting mode, the TOF flag gets set as the counter changes direction MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 403 Appendix B Timer Pulse-Width Modulator (TPMV2) at the transition from the value set in the modulus register and the next lower count value. This corresponds to the end of a PWM period. (The 0x0000 count value corresponds to the center of a period.) B.4.3 Channel Event Interrupt Description The meaning of channel interrupts depends on the current mode of the channel (input capture, output compare, edge-aligned PWM, or center-aligned PWM). When a channel is configured as an input capture channel, the ELSnB:ELSnA control bits select rising edges, falling edges, any edge, or no edge (off) as the edge that triggers an input capture event. When the selected edge is detected, the interrupt flag is set. The flag is cleared by the 2-step sequence described in Section B.4.1, "Clearing Timer Interrupt Flags." When a channel is configured as an output compare channel, the interrupt flag is set each time the main timer counter matches the 16-bit value in the channel value register. The flag is cleared by the 2-step sequence described in Section B.4.1, "Clearing Timer Interrupt Flags." B.4.4 PWM End-of-Duty-Cycle Events For channels that are configured for PWM operation, there are two possibilities: * When the channel is configured for edge-aligned PWM, the channel flag is set when the timer counter matches the channel value register that marks the end of the active duty cycle period. * When the channel is configured for center-aligned PWM, the timer count matches the channel value register twice during each PWM cycle. In this CPWM case, the channel flag is set at the start and at the end of the active duty cycle, which are the times when the timer counter matches the channel value register. The flag is cleared by the 2-step sequence described in Section B.4.1, "Clearing Timer Interrupt Flags." MC9S08DZ60 Series Data Sheet, Rev. 4 404 Freescale Semiconductor Appendix C Ordering Information and Mechanical Drawings C.1 Ordering Information This section contains ordering information for MC9S08DZ60 Series devices. Example of the device numbering system: MC 9 S08 DZ 60 F1 M XX Status (MC = Fully Qualified) (S = Auto Qualified) Memory (9 = Flash-based) Core Package designator (see Table C-2) Temperature range (C = -40C to 85C) (V = -40C to 105C) (M = -40C to 125C) Family Mast Set Identifier Only appears for "Auto Qualified" part numbers beginning with "S" F1 = 1M74K mask set Approximate Flash size in KB C.1.1 MC9S08DZ60 Series Devices Table C-1. Devices in the MC9S08DZ60 Series Memory Available Packages1 Device Number 1 C.2 FLASH RAM EEPROM MC9S08DZ60 60,032 4096 2048 MC9S08DZ48 49,152 3072 1536 MC9S08DZ32 33,792 2048 1024 MC9S08DZ16 16,896 1024 512 64-LQFP, 48-LQFP, 32-LQFP 48-LQFP, 32-LQFP See Table C-2 for package information. Mechanical Drawings The following pages are mechanical drawings for the packages described in the following table: MC9S08DZ60 Series Data Sheet, Rev. 4 Freescale Semiconductor 405 Appendix C Ordering Information and Mechanical Drawings Table C-2. Package Descriptions Pin Count 64 Type Low Quad Flat Package Abbreviation Designator Document No. LQFP LH 98ASS23234W 48 Low Quad Flat Package LQFP LF 98ASH00962A 32 Low Quad Flat Package LQFP LC 98ASH70029A MC9S08DZ60 Series Data Sheet, Rev. 4 406 Freescale Semiconductor How to Reach Us: Home Page: www.freescale.com E-mail: support@freescale.com USA/Europe or Locations Not Listed: Freescale Semiconductor Technical Information Center, CH370 1300 N. Alma School Road Chandler, Arizona 85224 +1-800-521-6274 or +1-480-768-2130 support@freescale.com Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) support@freescale.com Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor China Ltd. Exchange Building 23F No. 118 Jianguo Road Chaoyang District Beijing 100022 China +86 10 5879 8000 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or 1-303-675-2140 Fax: 1-303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com MC9S08DZ60 Rev. 4, 6/2008 Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals", must be validated for each customer application by customer's technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. RoHS-compliant and/or Pb-free versions of Freescale products have the functionality and electrical characteristics as their non-RoHS-compliant and/or non-Pb-free counterparts. For further information, see http://www.freescale.com or contact your Freescale sales representative. For information on Freescale's Environmental Products program, go to http://www.freescale.com/epp. FreescaleTM and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. (c) Freescale Semiconductor, Inc. 2007-2008. All rights reserved.