Features * * * * * * * * * * * * * Single Supply Voltage, Range 3V to 3.6V 3-volt Only Read and Write Operation Software Protected Programming Fast Read Access Time - 120 ns Low Power Dissipation - 15 mA Active Current - 40 A CMOS Standby Current Sector Program Operation - Single Cycle Reprogram (Erase and Program) - 1024 Sectors (128 Bytes/Sector) - Internal Address and Data Latches for 128 Bytes Two 8K Bytes Boot Blocks with Lockout Fast Sector Program Cycle Time - 20 ms Internal Program Control and Timer DATA Polling for End of Program Detection Typical Endurance > 10,000 Cycles CMOS and TTL Compatible Inputs and Outputs Commercial and Industrial Temperature Ranges 1. Description The AT29LV010A is a 3-volt only in-system Flash programmable and erasable read only memory (Flash). Its 1 megabit of memory is organized as 131,072 bytes by 8 bits. Manufactured with Atmel's advanced nonvolatile CMOS technology, the device offers access times to 120 ns with power dissipation of just 54 mW over the commercial temperature range. When the device is deselected, the CMOS standby current is less than 40 A. The device endurance is such that any sector can typically be written to in excess of 10,000 times. 1-megabit (128K x 8) 3-volt Only Flash Memory AT29LV010A Not Recommended for New Design Use AT29BV010A Contact Atmel to discuss the latest design in trends and options To allow for simple in-system reprogrammability, the AT29LV010A does not require high input voltages for programming. Three-volt-only commands determine the operation of the device. Reading data out of the device is similar to reading from an EPROM. Reprogramming the AT29LV010A is performed on a sector basis; 128 bytes of data are loaded into the device and then simultaneously programmed. During a reprogram cycle, the address locations and 128 bytes of data are captured at microprocessor speed and internally latched, freeing the address and data bus for other operations. Following the initiation of a program cycle, the device will automatically erase the sector and then program the latched data using an internal control timer. The end of a program cycle can be detected by DATA polling of I/O7. Once the end of a program cycle has been detected, a new access for a read or program can begin. 0520F-FLASH-9/08 2. Pin Configurations Function A0 - A16 Addresses CE Chip Enable OE Output Enable WE Write Enable I/O0 - I/O7 Data Inputs/Outputs NC No Connect 32-lead PLCC Top View 29 28 27 26 25 24 23 22 21 14 15 16 17 18 19 20 5 6 7 8 9 10 11 12 13 A14 A13 A8 A9 A11 OE A10 CE I/O7 I/O1 I/O2 GND I/O3 I/O4 I/O5 I/O6 A7 A6 A5 A4 A3 A2 A1 A0 I/O0 4 3 2 1 32 31 30 A12 A15 A16 NC VCC WE NC 2.1 Pin Name 2.2 32-lead TSOP Top View - Type 1 A11 A9 A8 A13 A14 NC WE VCC NC A16 A15 A12 A7 A6 A5 A4 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 OE A10 CE I/O7 I/O6 I/O5 I/O4 I/O3 GND I/O2 I/O1 I/O0 A0 A1 A2 A3 AT29LV010A 0520F-FLASH-9/08 AT29LV010A 3. Block Diagram 4. Device Operation 4.1 Read The AT29LV010A is accessed like an EPROM. When CE and OE are low and WE is high, the data stored at the memory location determined by the address pins is asserted on the outputs. The outputs are put in the high impedance state whenever CE or OE is high. This dual-line control gives designers flexibility in preventing bus contention. 4.2 Software Data Protection Programming The AT29LV010A has 1024 individual sectors, each 128 bytes. Using the software data protection feature, byte loads are used to enter the 128 bytes of a sector to be programmed. The AT29LV010A can only be programmed or reprogrammed using the software data protection feature. The device is programmed on a sector basis. If a byte of data within the sector is to be changed, data for the entire 128-byte sector must be loaded into the device. The data in any byte that is not loaded during the programming of its sector will be indeterminate. The AT29LV010A automatically does a sector erase prior to loading the data into the sector. An erase command is not required. Software data protection protects the device from inadvertent programming. A series of three program commands to specific addresses with specific data must be presented to the device before programming may occur. The same three program commands must begin each program operation. All software program commands must obey the sector program timing specifications. Power transitions will not reset the software data protection feature; however, the software feature will guard against inadvertent program cycles during power transitions. Any attempt to write to the device without the 3-byte command sequence will start the internal write timers. No data will be written to the device; however, for the duration of tWC, a read operation will effectively be a polling operation. After the software data protection's 3-byte command code is given, a byte load is performed by applying a low pulse on the WE or CE input with CE or WE low (respectively) and OE high. The address is latched on the falling edge of CE or WE, whichever occurs last. The data is latched by the first rising edge of CE or WE. The 128 bytes of data must be loaded into each sector. Any byte that is not loaded during the programming of its sector will be erased to read FFh. Once the bytes of a sector are loaded into 3 0520F-FLASH-9/08 the device, they are simultaneously programmed during the internal programming period. After the first data byte has been loaded into the device, successive bytes are entered in the same manner. Each new byte to be programmed must have its high to low transition on WE (or CE) within 150 s of the low-to-high transition of WE (or CE) of the preceding byte. If a high to low transition is not detected within 150 s of the last low-to-high transition, the load period will end and the internal programming period will start. A7 to A16 specify the sector address. The sector address must be valid during each high to low transition of WE (or CE). A0 to A6 specify the byte address within the sector. The bytes may be loaded in any order; sequential loading is not required. Once a programming operation has been initiated, and for the duration of tWC, a read operation will effectively be a polling operation. 4.3 Hardware Data Protection Hardware features protect against inadvertent programs to the AT29LV010A in the following ways: (a) VCC sense - if VCC is below 1.8V (typical), the program function is inhibited; (b) VCC power on delay - once VCC has reached the VCC sense level, the device will automatically time out 10 ms (typical) before programming; (c) Program inhibit - holding any one of OE low, CE high or WE high inhibits program cycles; and (d) Noise filter - pulses of less than 15 ns (typical) on the WE or CE inputs will not initiate a program cycle. 4.4 Input Levels While operating with a 3.3V 0.3V power supply, the address inputs and control inputs (OE, CE and WE) may be driven from 0 to 5.5V without adversely affecting the operation of the device. The I/O lines can be driven from 0 to VCC + 0.6V. 4.5 Product Identification The product identification mode identifies the device and manufacturer as Atmel. It may be accessed by hardware or software operation. The hardware operation mode can be used by an external programmer to identify the correct programming algorithm for the Atmel product. In addition, users may wish to use the software product identification mode to identify the part (i.e. using the device code), and have the system software use the appropriate sector size for program operations. In this manner, the user can have a common board design for 256K to 4-megabit densities and, with each density's sector size in a memory map, have the system software apply the appropriate sector size. For details, see Operating Modes (for hardware operation) or Software Product Identification. The manufacturer and device code is the same for both modes. 4.6 DATA Polling The AT29LV010A features DATA polling to indicate the end of a program cycle. During a program cycle an attempted read of the last byte loaded will result in the complement of the loaded data on I/O7. Once the program cycle has been completed, true data is valid on all outputs and the next cycle may begin. DATA polling may begin at any time during the program cycle. 4.7 Toggle Bit In addition to DATA polling the AT29LV010A provides another method for determining the end of a program or erase cycle. During a program or erase operation, successive attempts to read data from the device will result in I/O6 toggling between one and zero. Once the program cycle has completed, I/O6 will stop toggling and valid data will be read. Examining the toggle bit may begin at any time during a program cycle. 4 AT29LV010A 0520F-FLASH-9/08 AT29LV010A 4.8 Optional Chip Erase Mode The entire device can be erased by using a 6-byte software code. Please see Software Chip Erase application note for details. 4.9 Boot Block Programming Lockout The AT29LV010A has two designated memory blocks that have a programming lockout feature. This feature prevents programming of data in the designated block once the feature has been enabled. Each of these blocks consists of 8K bytes; the programming lockout feature can be set independently for either block. While the lockout feature does not have to be activated, it can be activated for either or both blocks. These two 8K memory sections are referred to as boot blocks. Secure code which will bring up a system can be contained in a boot block. The AT29LV010A blocks are located in the first 8K bytes of memory and the last 8K bytes of memory. The boot block programming lockout feature can therefore support systems that boot from the lower addresses of memory or the higher addresses. Once the programming lockout feature has been activated, the data in that block can no longer be erased or programmed; data in other memory locations can still be changed through the regular programming methods. To activate the lockout feature, a series of seven program commands to specific addresses with specific data must be performed. Please see Boot Block Lockout Feature Enable Algorithm. If the boot block lockout feature has been activated on either block, the chip erase function will be disabled. 4.9.1 Boot Block Lockout Detection A software method is available to determine whether programming of either boot block section is locked out. See Software Product Identification Entry and Exit sections. When the device is in the software product identification mode, a read from location 00002H will show if programming the lower address boot block is locked out while reading location 1FFF2H will do so for the upper boot block. If the data is FE, the corresponding block can be programmed; if the data is FF, the program lockout feature has been activated and the corresponding block cannot be programmed. The software product identification exit mode should be used to return to standard operation. 5. Absolute Maximum Ratings* Temperature Under Bias............................... -55 C to +125 C Storage Temperature .................................... -65 C to +150 C All Input Voltages (including NC Pins) with Respect to Ground ...................................-0.6V to +6.25V All Output Voltages with Respect to Ground .............................-0.6V to VCC + 0.6V *NOTICE: Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Voltage on A9 (including NC Pins) with Respect to Ground ...................................-0.6V to +13.5V 5 0520F-FLASH-9/08 6. DC and AC Operating Range Com. AT29LV010A-12 AT29LV010A-15 AT29LV010A-20 AT29LV010A-25 0C - 70C 0C - 70C 0C - 70C 0C - 70C -40C - 85C -40C - 85C -40C - 85C -40C - 85C 3.3V 0.3V 3.3V 0.3V 3.3V 0.3V 3.3V 0.3V Operating Temperature (Case) Ind. (1) VCC Power Supply Notes: 1. After power is applied and VCC is at the minimum specified data sheet value, the system should wait 20 ms before an operational mode is started. .2 Not recommended for New Designs. 7. Operating Modes Mode Read Program (2) 5V Chip Erase CE OE WE Ai I/O VIL VIL VIH Ai DOUT VIL VIH VIL Ai DIN VIL VIH VIL Ai X (1) VIH X X Program Inhibit X X VIH Program Inhibit X VIL X Output Disable X VIH X VIL VIL VIH Standby/Write Inhibit High Z High Z Product Identification Hardware A1 - A16 = VIL, A9 = VH,(3) A0 = VIL Manufacturer Code(4) A1 - A16 = VIL, A9 = VH,(3) A0 = VIH Device Code(4) A0 = VIL, A1 - A16 =VIL Manufacturer Code(4) A0 = VIH, A1 - A16 =VIL Device Code(4) Software(5) Notes: 1. 2. 3. 4. 5. X can be VIL or VIH. Refer to AC Programming Waveforms. VH = 12.0V 0.5V. Manufacturer Code is 1F. The Device Code is 35. See details under Software Product Identification Entry/Exit. 8. DC Characteristics Symbol Parameter Condition ILI Input Load Current ILO Max Units VIN = 0V to VCC 1 A Output Leakage Current VI/O = 0V to VCC 1 A Com. 40 ISB1 VCC Standby Current CMOS CE = VCC - 0.3V to VCC A Ind. 50 A ISB2 VCC Standby Current TTL CE = 2.0V to VCC 1 mA ICC VCC Active Current f = 5 MHz; IOUT = 0 mA; VCC = 3.6V 15 mA VIL Input Low Voltage 0.6 V VIH Input High Voltage VOL Output Low Voltage IOL = 1.6 mA; VCC = 3.0V VOH Output High Voltage IOH = -100 A; VCC = 3.0V 6 Min 2.0 V 0.45 2.4 V V AT29LV010A 0520F-FLASH-9/08 AT29LV010A 9. AC Read Characteristics AT29LV010A-12 AT29LV010A-15 AT29LV010A-20 Symbol Parameter tACC Address to Output Delay 120 150 tCE(1) CE to Output Delay 120 150 tOE(2) OE to Output Delay 0 50 0 70 0 100 tDF(3)(4) CE or OE to Output Float 0 30 0 40 0 50 tOH Output Hold from OE, CE or Address, whichever occurred first 0 Note: Min Max Min 0 Max Min 0 Max AT29LV010A-25 Min Max Units 200 250 ns 200 250 ns 0 120 ns 0 60 ns 0 ns Not recommended for New Designs. 10. AC Read Waveforms(1)(2)(3)(4) Notes: 1. CE may be delayed up to tACC - tCE after the address transition without impact on tACC. 2. OE may be delayed up to tCE - tOE after the falling edge of CE without impact on tCE or by tACC - tOE after an address change without impact on tACC. 3. tDF is specified from OE or CE whichever occurs first (CL = 5 pF). 4. This parameter is characterized and is not 100% tested. 7 0520F-FLASH-9/08 11. Input Test Waveforms and Measurement Level tR, tF < 5 ns 12. Output Test Load 13. Pin Capacitance f = 1 MHz, T = 25C(1) Symbol CIN COUT Note: 8 Typ Max Units Conditions 4 6 pF VIN = 0V 8 12 pF VOUT = 0V 1. These parameters are characterized and not 100% tested. AT29LV010A 0520F-FLASH-9/08 AT29LV010A 14. AC Byte Load Characteristics Symbol Parameter Min Max Units tAS, tOES Address, OE Set-up Time 10 ns tAH Address Hold Time 100 ns tCS Chip Select Set-up Time 0 ns tCH Chip Select Hold Time 0 ns tWP Write Pulse Width (WE or CE) 200 ns tDS Data Set-up Time 100 ns tDH, tOEH Data, OE Hold Time 10 ns tWPH Write Pulse Width High 200 ns 15. AC Byte Load Waveforms(1)(2) 15.1 WE Controlled 15.2 CE Controlled 9 0520F-FLASH-9/08 16. Program Cycle Characteristics Symbol Parameter Min Max Units tWC Write Cycle Time 20 ms tAS Address Set-up Time 10 ns tAH Address Hold Time 100 ns tDS Data Set-up Time 100 ns tDH Data Hold Time 10 ns tWP Write Pulse Width 200 ns tBLC Byte Load Cycle Time tWPH Write Pulse Width High s 150 200 ns 17. Software Protected Program Waveform Notes: 1. OE must be high when WE and CE are both low. 2. A7 through A16 must specify the sector address during each high to low transition of WE (or CE) after the software code has been entered. 3. All bytes that are not loaded within the sector being programmed will be indeterminate. 18. Programming Algorithm(1) LOAD DATA AA TO ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA Notes: 10 LOAD DATA A0 TO ADDRESS 5555 WRITES ENABLED LOAD DATA TO SECTOR (128 BYTES)(3) ENTER DATA PROTECT STATE(2) 1. Data Format: I/O7 - I/O0 (Hex); Address Format: A14 - A0 (Hex). 2. Data Protect state will be re-activated at end of program cycle. 3. 128 bytes of data MUST BE loaded. AT29LV010A 0520F-FLASH-9/08 AT29LV010A 19. Data Polling Characteristics(1) Symbol Parameter tDH Data Hold Time tOEH OE Hold Time Typ Max ns 10 ns OE to Output Delay Write Recovery Time tWR Units 10 (2) tOE Notes: Min ns 0 ns 1. These parameters are characterized and not 100% tested. 2. See tOE spec in AC Read Characteristics. 20. Data Polling Waveforms 21. Toggle Bit Characteristics(1) Symbol Parameter Min tDH Data Hold Time 10 ns tOEH OE Hold Time 10 ns tOE OE to Output Delay(2) tOEHP OE High Pulse tWR Write Recovery Time Notes: Typ Max Units ns 150 ns 0 ns 1. These parameters are characterized and not 100% tested. 2. See tOE spec in AC Read Characteristics. 22. Toggle Bit Waveforms(1)(3) Notes: 1. Toggling either OE or CE or both OE and CE will operate toggle bit. 2. Beginning and ending state of I/O6 will vary. 3. Any address location may be used but the address should not vary. 11 0520F-FLASH-9/08 23. Software Product Identification Entry(1) 25. Boot Block Lockout Feature Enable Algorithm(1) LOAD DATA AA TO ADDRESS 5555 LOAD DATA AA TO ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA 90 TO ADDRESS 5555 LOAD DATA 80 TO ADDRESS 5555 PAUSE 20 mS LOAD DATA AA TO ADDRESS 5555 ENTER PRODUCT IDENTIFICATION MODE(2)(3)(5) LOAD DATA 55 TO ADDRESS 2AAA 24. Software Product Identification Exit(1) LOAD DATA AA TO ADDRESS 5555 LOAD DATA 40 TO ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA F0 TO ADDRESS 5555 Notes: PAUSE 20 mS Notes: 12 EXIT PRODUCT IDENTIFICATION MODE(4) LOAD DATA 00 TO ADDRESS 00000H(2) LOAD DATA FF TO ADDRESS 1FFFFH(3) PAUSE 20 mS PAUSE 20 mS 1. Data Format: I/O7 - I/O0 (Hex); Address Format: A14 - A0 (Hex). 2. Lockout feature set on lower address boot block. 3. Lockout feature set on higher address boot block. 1. Data Format: I/O7 - I/O0 (Hex); Address Format: A14 - A0 (Hex). 2. A1 - A16 = VIL. Manufacturer Code is read for A0 = VIL; Device Code is read for A0 = VIH. 3. The device does not remain in identification mode if powered down. 4. The device returns to standard operation mode. 5. Manufacturer Code is 1F. The Device Code is 35. AT29LV010A 0520F-FLASH-9/08 AT29LV010A 26. Ordering Information 26.1 Standard Package tACC (ns) ICC (mA) Active Standby Package 32J 32T Operation Range Commercial (0 to 70 C) 15 0.04 AT29LV010A-12JC AT29LV010A-12TC 15 0.05 AT29LV010A-12JI AT29LV010A-12TI 32J 32T Industrial (-40 to 85 C) 15 0.04 AT29LV010A-15JC AT29LV010A-15TC 32J 32T Commercial (0 to 70 C) 15 0.05 AT29LV010A-15JI AT29LV010A-15TI 32J 32T Industrial (-40 to 85 C) 15 0.04 AT29LV010A-20JC AT29LV010A-20TC 32J 32T Commercial (0 to 70 C) 15 0.05 AT29LV010A-20JI AT29LV010A-20TI 32J 32T Industrial (-40 to 85 C) 15 0.04 AT29LV010A-25JC AT29LV010A-25TC 32J 32T Commercial (0 to 70 C) 15 0.05 AT29LV010A-25JI AT29LV010A-25TI 32J 32T Industrial (-40 to 85 C) 120 150 200 250 Note: Ordering Code Not recommended for New Designs. Package Type 32J 32-Lead, Plastic J-Leaded Chip Carrier (PLCC) 32T 32-Lead, Thin Small Outline Package (TSOP) 13 0520F-FLASH-9/08 27. Packaging Information 27.1 32J - PLCC 1.14(0.045) X 45 PIN NO. 1 IDENTIFIER 1.14(0.045) X 45 0.318(0.0125) 0.191(0.0075) E1 E2 B1 E B e A2 D1 A1 D A 0.51(0.020)MAX 45 MAX (3X) COMMON DIMENSIONS (Unit of Measure = mm) D2 Notes: 1. This package conforms to JEDEC reference MS-016, Variation AE. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010"(0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102 mm) maximum. SYMBOL MIN NOM MAX A 3.175 - 3.556 A1 1.524 - 2.413 A2 0.381 - - D 12.319 - 12.573 D1 11.354 - 11.506 D2 9.906 - 10.922 E 14.859 - 15.113 E1 13.894 - 14.046 E2 12.471 - 13.487 B 0.660 - 0.813 B1 0.330 - 0.533 e NOTE Note 2 Note 2 1.270 TYP 10/04/01 R 14 2325 Orchard Parkway San Jose, CA 95131 TITLE 32J, 32-lead, Plastic J-leaded Chip Carrier (PLCC) DRAWING NO. REV. 32J B AT29LV010A 0520F-FLASH-9/08 AT29LV010A 27.2 32T - TSOP PIN 1 0 ~ 8 c Pin 1 Identifier D1 D L b e L1 A2 E A GAGE PLANE SEATING PLANE COMMON DIMENSIONS (Unit of Measure = mm) A1 MIN NOM MAX A - - 1.20 A1 0.05 - 0.15 A2 0.95 1.00 1.05 D 19.80 20.00 20.20 D1 18.30 18.40 18.50 Note 2 E 7.90 8.00 8.10 Note 2 L 0.50 0.60 0.70 SYMBOL Notes: 1. This package conforms to JEDEC reference MO-142, Variation BD. 2. Dimensions D1 and E do not include mold protrusion. Allowable protrusion on E is 0.15 mm per side and on D1 is 0.25 mm per side. 3. Lead coplanarity is 0.10 mm maximum. L1 0.25 BASIC b 0.17 0.22 0.27 c 0.10 - 0.21 e NOTE 0.50 BASIC 10/18/01 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 32T, 32-lead (8 x 20 mm Package) Plastic Thin Small Outline Package, Type I (TSOP) DRAWING NO. REV. 32T B 15 0520F-FLASH-9/08 Headquarters International Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309 78054 Saint-Quentin-enYvelines Cedex France Tel: (33) 1-30-60-70-00 Fax: (33) 1-30-60-71-11 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Technical Support Flash@atmel.com Sales Contact www.atmel.com/contacts Product Contact Web Site www.atmel.com Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL'S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL'S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel's products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. (c) 2008 Atmel Corporation. All rights reserved. Atmel (R), Atmel logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. 0520F-FLASH-9/08