1
MS type Lower Profile Plug
H/MS Series
NEW
2004.6
Features
1. 20% Height Reduction
When compared with existing H/MS Series connectors
the overall height of plug assemblies is lower, allowing it
to be used in space constrained applications.
2. Cable Exit in 360° Directions
The cable can exit in any of the 8 fixed direction, in 45°
increments.
3. Simple Assembly
The 2-piece design consisting of the contact/insulator
assembly and the back-shell assembly allows termination
without the use of any specialized tools.
4. Water and Dust Protection
IP 67 rating when fully terminated and mated with
corresponding part.
5. TUV Certification
Provided with a protective circuit function for TUV
certification. The (D) pin is directly connected to the
outside metal case.
Applications
Factory automation equipment, robotic equipment, servo
motors, and a wide variety of industrial and measuring
instruments.
Plug
(45°)
Can be changed
in 45 degree increments
Connector Height Comparison
Existing MS Connector Lower-profile Plug
22-22 Size
Cable Exit Direction of 360°
Circular connector conforming to MIL-C-5015
PAT.P
50.1mm
54.5mm
70mm
3057-10
18
45.5mm
41mm
56.5mm
3057-10
48.2mm
60.7mm
78.7mm
3057-12
22
53.2mm
63.8mm
45.8mm
3057-12
Existing MS Connector Lower-profile Plug
18-10 Size
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
2
3 m ohms max. 1 m ohms max.
5000 M ohms min.
No flashover or insulation breakdown.
Contact resistance: Contact resistance:
4.5 m ohms max. 1.5 m ohms max.
Insulation resistance: 5000 M ohms min.
Insulation resistance: 50 M ohms min. (Humidity state)
500 M ohms min. (Dry state)
When mated with corresponding connector.
1A DC
500 V DC
2250V AC/one minute.
Frequency: 10 to 500 Hz, single amplitude of 0.75 mm,
acceleration of 98 m/s2for 3 hours in 3 axis.
Acceleration of 490 m/s2, 11ms duration, sine half-wave
waveform, 3 cycles in each of the 3 axis.
500 cycles
Temperature: -55ç Room temperature to +125ç Room
temperature Time: 30 10 to 15 30 10 to 15 (Minutes)
5 cycles.
96 hours at temperature of 71ç and humidity of 95% .
No dust penetration.
No water penetration when submerged for 0.5 hour at the depth of 1 meter.
1. Contact resistance
2.
Insulation resistance
3.
Withstanding voltage
4. Vibration
5. Shock
6. Durability
(insertion/ withdrawal)
7. Temperature cycle
8. Humidity
9. Water/dust
protection
Rating
Voltage rating 250VAC, 250V DC (pollution degree: 3, overvoltage category: 3)
500V AC, 500V DC (pollution degree: 2, overvoltage category: 2)
Current rating 23A Max. (18-10 size)
46A Max. (22-22 size)
Operating temperature range
-25ç to +125ç
Storage temperature range
-25ç to +125ç
Product Specifications
Materials
Item Specification
18-10 size 22-22 size Conditions
Body
Insulator
Socket Contacts
Gasket
Bushing
Aluminum alloy
PPS
Copper alloy
Silicone Rubber
Chloroprene rubber
Black chromate
Color: Black
Silver plating
Color: Black
Color: Black
-------------------
UL94V-0
-------------------
-------------------
-------------------
Item Material Finish Remarks
Additional Product Information
1. Product number suffixes
(10) Supplied with a wire hole in the locking ring (to prevent loosening of the ring).
(11) Supplied without the wire hole in the locking ring.
2. Corresponding receptacles.
18-10 Size: Part number H/MS3102A18-10P-D-T1(10)
22-22 Size: Part number H/MS3102A22-22P-D-T(10)
No electrical discontinuity for 10 ms max.
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
3
Plug
A
BC
18-10S
X
3057-10
D
41
31
Ø33.5
45.5
Part Number CL No.
Number of Contacts
H/MS08A18-10S-DT10D(10)
H/MS08A18-10S-DT10D(11)
H/MS08A18-10S-DT10D1(10)
H/MS08A18-10S-DT10D1(11)
120-0476-3-10
4
Weight
89g
Applicable Cable Diameter
Ø12~Ø14.3mm
Ø10~Ø12.5mm
Contact solder pot inner diameter
2.5mm
120-0476-3-11
120-0481-3-10
120-0481-3-10
Part Number CL No.
Number of Contacts
H/MS08A18-10S-DT10C(10)
H/MS08A18-10S-DT10C(11)
120-0480-0-10 4
Weight
77.6g
Applicable Cable Diameter
Ø13~Ø14.3mm
Contact solder pot inner diameter
2.5mm
120-0480-0-11
Part Number CL No.
Number of Contacts
H/MS08A22-22S-DT12D(10)
H/MS08A22-22S-DT12D(11)
H/MS08A22-22S-DT12D1(10)
H/MS08A22-22S-DT12D1(11)
120-0477-6-10
4
Weight
127g
Applicable Cable Diameter
Ø13~Ø15.9mm
Ø10~Ø13.5mm
Contact solder pot inner diameter
4.5mm
120-0477-6-11
120-0482-6-10
120-0482-6-11
Shown one type.
Shown one type.
Shown one type.
A
BC
18-10S
X
D
41
35.5
Ø30
Ø33.5
X
BC
22-22S
D
A
H/MS08A18-10S-DT10D(10)
H/MS08A18-10S-DT10C(10)
H/MS08A22-22S-DT12D(10)
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
3057-10
A
B
Bushing
Back-shell
Cable
Contacts
Strain relief clamp
Washer
Solder
Insulator/contact assembly
Pre-solder
Conductor portion
B
BA
4
BAssembly Procedures Outline of assemblyProcess
1
2
a. Pass the strain relief clamp, washer, bushing, and hood over the cable, in this order.
b. Prepare the cable and conductors per the dimensions in Table 1.
c. Bend the exposed conductor to the B dimension as indicated in Table 1.
d. Pre-solder the exposed conductor and solder it as shown to the exposed contact.
Note: Use care not to damage the conductor’s insulation.
a. Place over the contact/insulator assembly (in the following order:Back shell, bushing, washer, strain relief clamp).
b. Tighten the Locking ring and Cable clamp to the torque values per Table 2.
c. Tighten the set screw to a torque value of 0.3-0.4 N-m
HRS recommended tool: PB205/1.27 (CL150-0066-3)or equivalent.
d. Using screwdriver tighten the two strain relief clamp screws until both sides of the moveable part are in contact with the cable clamp.
A B
18-10 Size
Table 1
22-22 Size
24mm 13mm
33mm 15mm
The contents of this catalog are current as of date of publication. Contents are subject to change without notice for the purpose of improvements.
5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN
PHONE: 81-3-3491-9741, FAX: 81-3-3493-2933
http://www.hirose.com
®
Locking Ring Cable Clamp
Table 2
3 to 3.5N m 5 to 6N m
3057-10
4.5 mm min.
Cable
Strain relief clamp
Back-shell
Locking ring
Screw
Clamp
Washer
Bushing
Set screw
(Hexagonal hole opposite side 1.27 mm)
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.