Data Sheet 100VAC Input/12VDC (100mA) Output Non-Isolated AC/DC Converter BP5034D12 Absolute Maximum Ratings Unit Vi Io Vsurge Topr Tstg 195 100 2 -25 to +80 -25 to +105 V mApk kV C C 28.2MAX. 10.0MAX. Mark Side Limits 15.7MAX. Symbol 1 41.0 Parameter Input voltage Output current ESD endurance Operating temperature range Storage temperature range Dimensions (Unit : mm) 2 3 4 5 6 7 8 10 0.25 0.05 0 . 5 0 . 1 1 . 3 0 . 2 P = 2 . 5 4 0 . 2 3.25MAX. 3.5MAX. 6.5MAX. 2.549=22.86 Electrical Characteristics Derating curve Conditions DC(80 to 138VAC level) Vi=141V, Io=50mA Vi=141V Vi=113 to 195V, Io=50mA Vi=141V, Io=0 to 50mA Vi=141V, Io=50mA Vi=141V, Io=100mA 1 The max output is changed due to the ambient temperature. Please refer to note regarding derating curve. 2 Please refer to Conversion efficiency. Application Circuit Pin No. 1 2 3 4 5 6 7 8 9 10 BP5034D12 Please note that pin No.10 side is input. 10 Input AC100V 50Hz/60Hz ZNR + 220V - 8 7 6 5 4 3 2 1 FUSE 0.5A R1 D1 1SR35-400A 101/4W C1 10F/250V Output +12V C2 + 0.1F - Terminal definition Output terminal Vo(12V) N.C. N.C. N.C. COMMON COMMON N.C. N.C. Skipping Pin Input terminal Vi(141VDC) C3 100F/50V Be sure to use fuse for safety. Please verify operation and characteristics in the customer's circuit before actual usage and ensure that the load current does not exceed 0.1A. FUSE: Fuse Use a fuse of 0.5A C1 : Input smoothing capacitor Capacitance : 3.3 to 22F Ripple current is 0.13Arms or above. Rated voltage : 200V or higher C2 : Noise reduction capacitor Capacitance : 0.1 to 0.22F Rated voltage : 200V or higher Use a film or ceramic capacitor. Evaluate under actual operating conditions. C3 : Output smoothing capacitor Capacitance : 100 to 470F Rated voltage : 25V or higher, low impedance Impedance is 0.39 max at high frequencies. Ripple current is 0.1Arms or above. Capacitance impedance affects the output ripple voltage. In the absolute maximum ratings, the reverse surge voltage should be 400V or higher, the average rectifying current should be 0.5A or higher, and the forward surge current should be 20A or higher. R1 : Noise reduction resistor ZNR : Varistor 10 to 22 1/4W Determine the ideal value through actual testing. A varistor must be used to protect against lightning surges and static electricity. www.rohm.com (c)2010 ROHM Co., Ltd. All rights reserved. 1 100 80 60 20 0 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 Ambient Temperature Ta(C) 2 2 Operation Range 40 Switching Frequency 100 90 80 70 60 50 40 30 20 10 0 Switching Frequency (Ta=25C, Vi=141V) 0 20 40 60 80 Output Current Io(mA) 100 Conversion Efficiency 80 70 60 50 40 30 20 10 0 Conversion Efficiency (Ta=25C, Vi=141V) 60% Min-Line 0 20 40 60 80 Output Current Io(mA) 100 Load Regulation External Component Specifications D1 : Rectifier diode Derating Curve 120 Output Current Io(mA) Unit V V mA V V Vp-p % Switching Frequency fsw(kHz) Max. 195 12.8 100 0.1 0.15 0.15 - Conversion Efficiency (%) Typ. 141 12 - 0.02 0.05 0.05 68 1/1 Output Voltage Vo(V) Min. 113 11 0 - - - 60 13.0 12.8 12.6 12.4 12.2 12.0 11.8 11.6 11.4 11.2 11.0 Load Regulation (Ta=25C, Vi=141V) 0 20 40 60 80 Output Current Io(mA) 100 Surface Temperature Increase Temperature Rising T(C) Symbol Parameter Input voltage range Vi Output voltage Vo Output current Io Line regulation Vr Load regulation Vl Output ripple voltage Vp Power conversion efficiency Surface Temperature Increase (Ta=25C, Vi=141V) 40 30 20 10 0 0 20 40 60 80 Output Current Io(mA) 100 2010.01 - Rev.A Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com (c) 2010 ROHM Co., Ltd. All rights reserved. R1010A