Technical Document LCD Specification LCD Group LQ035Q3DG01 LCD Module Product Specification October 2007 QVGA LCD Module featuring 450 nits brightness with 500:1 contrast. Full Specifications Listing LCY-W-07X04-1 NOTICE This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. The application circuit examples in this publication are provided to explain the representative applications of SHARP's devices and are not intended to guarantee any circuit design or permit any industrial property right or other rights to be executed. SHARP takes no responsibility for any problems related to any industrial property right or a third party resulting from the use of SHARP's devices, except for those resulting directly from device manufacturing processes. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP's device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structures and other contents described herein at any time without notice in order to improve design or reliability. Contact SHARP in order to obtain the latest specification sheets before using any SHARP's device. Manufacturing locations are also subject to change without notice. Observe the following points when using any device in this publication. SHARP takes no responsibility for damage caused by improper use of the devices. The devices in this publication are designed for use in general electronic equipment designs, such as: Personal computers Office automation Telecommunication equipment Test and measurement equipment Industrial control Audio visual and multimedia equipment Consumer electronics Personal Digital Assistant The appropriate design measures should be taken to ensure reliability and safety when SHARP's devices are used for equipment such as: Transportation control and safety equipment(i.e. aircraft, trains, automobiles, etc.) Traffic signals Alarm equipment Gas leakage sensor breakers Various safety devices etc. SHARP's devices shall not be used for equipment that requires extremely high level of reliability, such as: Military and space applications Nuclear power control equipment Medical equipment for life support Contact a SHARP representative, in advance, when intending to use SHARP's devices for any "specific" applications other than those recommended by SHARP. Contact and consult with a SHARP representative if there are any questions about the contents of this publication. LCY-W-07X04-2 1. Applicable Scope This specification is applicable to TFT-LCD Module "LQ035Q3DG01". 2. General Description This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a color TFT-LCD panel, driver IC, Input FPC, a back light unit. Graphics and texts can be displayed on a 320 x RGB x 240 dots panel with about 262k colors by supplying 18bit data signals (6bit x RGB), four timing signals, 3wires 9bit serial interface signals, logic (Typ. +3.3V), analog (Typ. +3.3V) supply voltages for TFT-LCD panel driving and supply voltage for back light. 3. Mechanical (Physical) Specifications Item Specifications Unit Screen size 8.8 (3.5" type) diagonal cm Active area 70.56 (H) x 52.92 (V) mm 320 (H) x 240 (V) pixel 1 Pixel = R+G+B dots - Pixel pitch 0.2205 (H) x 0.2205 (V) mm Pixel configuration R,G,B vertical stripes - Display mode Normally white - Unit outline dimensions * 76.9 (W) x 63.9 (H) x 3.5 (D) mm Mass Approx.33 g Surface treatment Anti glare - Pixel format *The above-mentioned table indicates module sizes without some projections and FPC. For detailed measurements and tolerances, please refer to 17. Outline Dimensions. LCY-W-07X04-3 4. Input Terminal Names and Functions Recommendation CN[HIROSE] FH26G-67S-0.3SHBW(05) Pin No. Symbol I/O Description Remarks 1 LED_C (-) - Power supply for LED (Low voltage) 2 LED_A(+) - Power supply for LED (High voltage) 3 DGND1 - Digital Ground 4 NC - Not connected Note 1 5 NC - Not connected Note 1 6 NC - Not connected Note 1 7 NC - Not connected Note 1 8 AGND1 - Analog Ground 9 VGH - Connect to a Stabilizing capacitor Note 3 10 C2P - Connect a Booster capacitor to C2N Note 2 11 C2N - Connect a Booster capacitor to C2P 12 C1P - Connect a Booster capacitor to C1N 13 C1N - Connect a Booster capacitor to C1P 14 VGL - Connect a Stabilizing capacitor to GND Note 3 15 C3N - Connect a Booster capacitor to C3P Note 2 16 C3P - Connect a Booster capacitor to C3N 17 AGND2 - Analog Ground 18 VCIX2 - Connect a Stabilizing capacitor to GND Note 3 19 CYP - Connect a Booster capacitor to CYN Note 2 20 CYN - Connect a Booster capacitor to CYP 21 VCI - Booster input voltage pin Note 3 22 NC - Not connected Note 1 23 AGND3 - Analog Ground 24 VCIM - Connect a Stabilizing capacitor to GND Note 3 25 CXP - Connect a Booster capacitor to CXN Note 2 26 CXN - Connect a Booster capacitor to CXP 27 TEST O TEST 28 RESB I System reset 29 DGND2 - Digital Ground 30 VDDIO - Voltage input pin for logic I/O 31 VCORE - Connect a Stabilizing capacitor to GND 32 DGND3 - Digital Ground 33 SHUT I Sleep mode control 34 CSB I Chip select pin of serial interface 35 SDI I Data input pin in serial mode 36 SCK I Clock input pin in serial mode 37 VDROP - Connect a Stabilizing capacitor 38 DEN I Display enable 39 B5 I BLUE data signal(MSB) 40 B4 I BLUE data signal 41 B3 I BLUE data signal Note 1 Note 3 LCY-W-07X04-4 Pin No. Symbol I/O Description 42 B2 I BLUE data signal 43 B1 I BLUE data signal 44 B0 I BLUE data signal(LSB) 45 G5 I GREEN data signal(MSB) 46 G4 I GREEN data signal 47 G3 I GREEN data signal 48 G2 I GREEN data signal 49 G1 I GREEN data signal 50 G0 I GREEN data signal(LSB) 51 R5 I RED data signal(MSB) 52 R4 I RED data signal 53 R3 I RED data signal 54 R2 I RED data signal 55 R1 I RED data signal 56 R0 I RED data signal(LSB) 57 VSYNC I Frame synchronization signal 58 HSYNC I Line synchronization signal 59 DOTCLK I Dot-clock signal 60 CDUM0 - Connect a Stabilizing capacitor to GND 61 DGND4 - Digital Ground 62 VLCD63 - Connect a Stabilizing capacitor to GND 63 VCOMH - Connect a Stabilizing capacitor to GND 64 VCOML - Connect a Stabilizing capacitor to GND 65 DGND5 - Digital Ground 66 CSVCMP - Connect a Stabilizing capacitor to CSVCMN 67 CSVCMN - Connect a Stabilizing capacitor to CSVCMP Note 1) this pin should be opened. Note 2) Booster Capacitors Remarks Note 3 Note 3 Note 3 LCY-W-07X04-5 Note 3) Stabilization and charge sharing Capacitors Remark All capacitors 2.2uF (2.2uF is preferred for better display quality and power consumption) LCY-W-07X04-6 5. Absolute Maximum Ratings Symbol Conditions Item Rated value Unit Remarks Note 1 Input voltage VI Ta = 25C -0.3 ~ VDDIO+0.3 V Logic I/O power supply voltage VDDIO Ta = 25C -0.3 ~ +4.0 V Analog power supply voltage VCI Ta = 25C AGND-0.3 ~ +5.0 V Temperature for storage Tstg - -30 ~ +80 C Note 2 Temperature for operation Topp - -20 ~ +70 C Note 3 LED input electric current ILED 35 mA LED electricity consumption PLED 123 mW TaLED = 25C TaLED = 25C Note 1) RESB, SHUT, CSB, SDI, SCK, DEN, B5~B0, G5~G0, R5~R0, VSYNC, HSYNC, DOTCLK Note 2) Humidity: 95%RH Max. (Ta40C) Maximum bulb temperature under 39C (Ta>40C) See to it that no dew will be condensed. Note 3) Panel surface temperature prescribes. Note 4) Power consumption of one LED (Ta LED= 25C). (use 7 pieces LED) Ambient temperature and the maximum input are fulfilling the following operating conditions. Ambient temperature of LED and the maximum input LCY-W-07X04-7 6. Electrical Characteristics 6-1. TFT LCD Panel Driving Ta = 25C Item Symbol Min. Typ. Max. Unit Remarks Logic I/O power supply DC voltage VDDIO +3.0 +3.3 +3.6 V DC Current IVDDIO - 0.20 0.35 mA Analog DC voltage VCI +3.0 +3.3 +3.6 V power supply DC Current IVCI - 8.0 12.0 mA Note 1 VRFVDDIO - - 100 mVp-p Note 2 VRFVCI - - 100 mVp-p Note 2 Permissive input Ripple voltage Note 1 Logic High VIH 0.8 VDDIO - VDDIO V Note 3 Input Voltage Low VIL 0 - 0.2 VDDIO V Note 3 IIH / IIL -1 - 1 A Note 3 Logic input Current Note 1) VDDIO = VCI = +3.3V Current situation for IVDDIO: Black & White checker flag pattern Current situation for ICI: All black pattern Note 2) VDDIO = VCI = +3.3V Note 3) RESB, SHUT, CSB, SDI, SCK, DEN, B5~B0, G5~G0, R5~R0, VSYNC, HSYNC, DOTCLK LCY-W-07X04-8 6-2. Register Setting This register setting is for DOTCLK=5MHz. If LCD module is moved other frequency, please conform display quality. Reg. # Register Data (Gamma 2.2) Remark R01 h Driver output control 2xEF h Note1 R02 h LCD drive AC control 0300 h R03 h Power control (1) 787E h R0B h Frame cycle control DC00 h R0C h Power control (2) 0005 h R0D h Power control (3) 0002 h R0E h Power control (4) 2900 h R0F h Gate scan starting Position 0000 h R16 h Horizontal Porch 9F86 h Note2 R17 h Vertical Porch 0002 h Note3 R1E h Power control (5) 0000 h R2E h Gamma control(1) B945 h R30 h Gamma control (2) 0301 h R31 h Gamma control (3) 0107 h R32 h Gamma control (4) 0000 h R33 h Gamma control (5) 0100 h R34 h Gamma control (6) 0707 h R35 h Gamma control (7) 0006 h R36 h Gamma control (8) 0604 h R37 h Gamma control (9) 0103 h R3A h Gamma control (10) 0D0F h R3B h Gamma control (11) 0D04 h R28 h Power control (6) 0006 h R2C h Power control (7) C88C h LCY-W-07X04-9 Note 1) Driver Output Control (R01h)(POR=2xEFh) DC W IB15 1 POR IB14 IB13 IB12 IB11 IB10 IB9 IB8 IB7 IB6 IB5 IB4 IB3 IB2 IB1 IB0 0 0 1 0 1 0 TB RL 1 1 1 0 1 1 1 1 0 0 1 0 1 0 x x 1 1 1 0 1 1 1 1 Vertical and Horizontal inversion function(TBRL) Note 2) Horizontal Porch(R16h)(POR=9F86h) R/W DC IB15 IB14 IB13 IB12 IB11 IB10 IB9 IB8 IB7 IB6 IB5 IB4 IB3 IB2 IB1 IB0 W 1 1 0 0 1 1 1 1 1 1 0 HBP5 HBP4 HBP3 HBP2 HBP1 HBP0 1 0 0 1 1 1 1 1 1 0 0 0 0 1 1 0 POR HBP5-0: Set the delay period from falling edge of HSYNC to first valid line. HBP5 HBP4 HBP3 HBP2 HBP1 HBP0 No. of clock cycle of DOTCLK 0 0 0 0 0 0 2 0 0 0 0 0 1 3 0 0 0 0 1 0 4 0 0 0 0 1 1 5 0 0 0 1 0 0 6 Step = 1 1 1 1 1 1 0 64 1 1 1 1 1 1 65 LCY-W-07X04-10 THBP : Set by HBP5-0 tHFP HDISP=320 XL8XL8-0: 320 Note 3) Vertical Porch(R17h)(POR=0002h) R/W DC IB15 IB14 IB13 IB12 IB11 IB10 IB9 IB8 IB7 IB6 IB5 IB4 IB3 IB2 IB1 IB0 W 1 0 0 0 0 0 0 0 VBP8 VBP7 VBP6 VBP5 VBP4 VBP3 VBP2 VBP1 VBP0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 POR VBP8-0 : Set the delay period from falling edge of VSYNC to first valid line. VBP8 VBP7 VBP6 VBP5 VBP4 VBP3 VBP2 VBP1 VBP0 No. of clock cycle of HSYNC 0 0 0 0 0 0 0 0 0 0(CAD=0 ) 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0 0 1 0 2 1 1 Step = 1 1 0 0 1 1 1 0 319 1 0 0 1 1 1 1 1 1 320 1 0 1 Reserved 1 1 Reserved Vcycle TVBP:Set by VBP8-0 VDISP=240 tVFP LCY-W-07X04-11 6-3. Back light driving The back light system has 7 LEDs Used LED : NSSW008C[Nichia Corporation] Parameter Symbol Min. VBL Rated Voltage IL Rated Current Power consumption WL - Typ. 22.4 20 448 Max. 24.5 - Unit V mA mW Remark TaLED=25C 7. Timing characteristics of input signals 7-1. Pixel Clock Timing Characteristics DOTCLK Symbol Min Typ Max Unit Frequency fDOTCLK - 5.0 8.0 MHz Period tDOTCLK 125 200 - nSec High Period tCKH 62 - - nSec Low Period tCKL 62 - - nSec Setup Time tds 30 - - nSec Hold Time tdh 30 - - nSec Setup Time tvsys 20 - - nSec Hold Time tvsyh 20 - - nSec Setup Time thsys 20 - - nSec Hold Time thsyh 20 - - nSec thv 0 - 320 tDOTCLK Reset Pulse Width tRES 10 - - nSec Rise / Fall Time tr/tf 20 - 100 nSec Data Vsync Hsync Phase difference of Sync signal Falling edge Note: External clock source must be provided to DOTCLK pin. The module will not operate If absent of the clocking signal. LCY-W-07X04-12 7-2. Data Transaction Timing in Normal Operating Mode (262k color) Characteristics DOTCLK Symbol Min Typ Max Unit Frequency fDOTCLK - 5.0 8.0 MHz Period tDOTCLK 125 200 - ns Frequency fh - 14.9 18.18 kHz Cycle Hcycle - 336 - clock Frequency fv 50 60.1 65 Hz Cycle Vcycle - 244 - line Horizontal Back Porch tHBP - 8 - clock Horizontal Front Porch tHFP - 8 - clock Horizontal Data Start Point tHBP - 8 - clock Horizontal Blanking Period tHBP+tHFP - 16 - clock Horizontal Display Area HDISP - 320 - clock Vertical Back Porch tVBP - 2 - line Vertical Front Porch tVFP - 2 - line Vertical Data Start Point tVBP - 2 - line Vertical Blanking Period tHBP+tHFP - 4 - line Vertical Display Area VDISP - 240 - line HSYNC VSYNC LCY-W-07X04-13 The formula of setting for control signals: fDOTCLK, tHBP, tHFP, tVBP, tVFP fv=605Hz fv= fDOTCLK/( Vcyclex Hcycle) Vcycle=240+ tVBP + tVFP Hcycle=320+ tHBP+ tHFP 512 7-3. Synchronization Signals Timing in Power Save Mode (8 color) Characteristics Symbol Min Typ Max Unit Frequency fDOTCLK - 5.0 8.0 MHz Period tDOTCLK 125 200 - ns HSYNC Frequency fh - 14.9 18.18 kHz VSYNC Frequency fv 50 60.1 65 Hz Cycle Vcycle - 244 - line Vertical Partial Back Porch VPBP 0 - 239 line Vertical Active Area VPDSP 1 - 240 line Vertical Back Porch tVBP - 2 - line Vertical Front Porch tVFP - 2 - line Vertical Display Area VDISP - 240 - line DOTCLK Note : When entered to 8-color display mode, the RGB graphie data through the interface pin RR5,GG5 and BB5 are valid within the Vertical Active Area. Data "0" will be displayed the Vertical Active Area. The formula of setting for control signals: fDOTCLK, tHBP, tHFP, tVBP, tVFP fv=605Hz fv= fDOTCLK/( Vcyclex Hcycle) Vcycle=240+ tVBP + tVFP Hcycle=320+ tHBP+ tHFP 512 LCY-W-07X04-14 7-4. VGH Output against SHUT & RESB VCI CI/VDDIO V VDDIO RESB RESB RESB. LCY-W-07X04-15 7-5. Power Up Sequence VCI/VDDIO (The internal signal of LCD module) Note1: It is necessary to input DOTCLK before the falling edge of SHUT. Note2: Display starts at 10th falling edge of VSYNC after the falling edge of SHUT. LCY-W-07X04-16 7-6. Power Down Sequence VCI/VDDIO RESB (The internal signal of LCD module) Note1: DOTCLK must be maintained at least 2 frames after the rising edge of SHUT. Note2: Display become off at the 2nd falling of VSYNC after the falling edge of SHUT. Note3: IF RESET(RES) signal is necessary for power down,provide it after the 2-frames-cycle of the SHUT period. LCY-W-07X04-17 7-7. SPI Interface Timing Diagram & Transaction Example (9 bit) Min Typ Max Frequency fclk - - 20 MHz Cycle Time tclk 50 - - ns Low Width tsl 25 - - ns High Width tsh 25 - - ns Setup Time tcss 0 - - ns Hold time tcsh 10 - - ns High Delay Time tcsd 20 - - ns Setup Time tds 5 - - ns Hold Time tdh 10 - - ns Characteristics Serial Clock Chip Select Data The example transmit "0x2AEFh" to register R01h. LCY-W-07X04-18 7-8. Input Data Signals and Display Position on the screen Please refer to Input Terminal Names and Functions LCY-W-07X04-19 8. Input Signals, Basic Display Colors and Gray Scale of Each Color Date signal Colors & Basic Color Gray Scale of Red Gray Scale of Green Gray Scale of Blue Gray Gray R0 R1 R2 R3 R4 R5 Scale Scale LSB Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 Green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 Cyan 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Magenta 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 Yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GS1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Darker GS2 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Brighter GS61 1 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 GS62 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Red GS63 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GS1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 Darker GS2 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 Brighter GS61 0 0 0 0 0 0 1 0 1 1 1 1 0 0 0 0 0 0 GS62 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 Green GS63 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GS1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 Darker GS2 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 Brighter GS61 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1 GS62 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 Blue GS63 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 MSB G0 G1 G2 G3 G4 LSB G5 MSB B0 B1 B2 B3 B4 LSB B5 MSB 0: Low level voltage, 1: High level voltage Each basic color can be displayed in 64 gray scales from 6 bit data signals. According to the combination of 18 bit data signals, the 262k color display can be achieved on the screen. LCY-W-07X04-20 9. Optical Characteristics Ta = 25C, VDDIO = +3.3V, VCI = +3.3V Parameter Viewing angle Horizontal Min. Typ. Max. Unit Vertical Contrast ratio Condition - 70 - deg. - 70 - deg. 11 - 60 - deg. 12 - 65 - deg. 300 500 - - 8 20 ms - 20 40 ms 21 22 range (With Wide View) Symbol CR Response Rise r Time Decay d CR10 Optimum viewing angle =0 Remark Note1,4 Note2,4 Chromaticity of x 0.26 0.31 0.36 White y 0.29 0.34 0.39 Luminance of white XL1 350 450 - Note3,4 Note4 cd/m2 ILED=20mA * The optical characteristics measurements are operated under a stable luminescence (ILED = 20mA) and a dark condition. (Refer to Fig.9-1) Instrument luminance,contrast(BM-5A) chromaticity (SR-3) Instrument(EZ-CONTRAST mm Field=2 Center of display(=0 Center of display (=0) TFT-LCD module TFT-LCD module Fig 9-1 characteristics measurements Fig 9-2 characteristics measurements of luminance, of viewing angle/Response time contrast and chromaticity LCY-W-07X04-21 Note 1 Definitions of viewing angle range Normal line 22 11 12 21 6 o'clock Note 2 Definition of contrast ratio The contrast ratio is defined as the following Contrast ratio (CR) = Luminance (brightness) with all pixels white Luminance (brightness) with all pixels black Note 3 Definition of response time The response time is defined as the following figure and shall be measured by switching the input signal for "Black" and "White" White White Photo detector output (Relative value) Black Black Time Note 4 This shall be measured at center of the screen. LCY-W-07X04-22 10 Handling of modules 10-1. Inserting the FPC into its connector and pulling it out 1) Be sure to turn off the power supply and the signals when inserting or disconnecting the cable. 2) Please insert for too much stress not to join FPC in the case of insertion of FPC. 10-2. About handling of FPC 1) The bending radius of the FPC should be more than 1.4mm, and it should be bent evenly. 2) Do not dangle the LCD module by holding the FPC, or do not give any stress to it. 10-3. Mounting of the module 1) The module should be held on to the plain surface. Do not give any warping or twisting stress to the module. 2) Please consider that GND can ground a modular metal portion etc. so that static electricity is not charged to a module. 10-4. Cautions in assembly / Handling pre cautions As the polarizer can be easily scratched, be most careful in handling it. 1) Work environments in assembly. Since removing laminator may causes electrostatic charge that tends to attract dust, the following work environment would be desired. a) Floor: Conductive treatment having 1M resistance onto floor's tile b) The room free from dust coming from outdoor environment, and put an adhesive mat at entrances. c) Humidity from 50% to 70% and temperature from 15C to 27C are desirable. d) Worker should ware conductive shoes, conductive fatigue, conductive glove and earth wrist band. 2) Instruction for working Wind Flow Antistatic Blower The best distance of use blower cellophane tape LCD Module Input FPC side a) Wind direction of an antistatic blower should slightly downward to properly blow the module. The distance between the blower and the module should be the best distance of use blower. Also, pay attention to the direction of the module. b) To prevent polarizer from scratching, adhesive tape (cellophane tape) should be stuck at the part of laminator sheet, which is closed to blower. [See the above] c) Pull slowly adhesive tape to peel the laminator off, with spending more than 5 second. d) The module without laminator should be moved to the next process to prevent adhesion of dust. LCY-W-07X04-23 3) How the remove dust on the polarizer a) Blow out dust by the use of an N2 blower with antistatic measures taken. Use of an ionized air Gun is recommendable. b) When the panel surface is soiled, wipe it with soft cloth. 4) In the case of the module's metal part (shield case) is stained, wipe it with a piece of dry, soft cloth. If rather difficult, give a breath on the metal part to clean better. 5) If water dropped, etc. remains stuck on the polarizer for a long time, it is apt to get discolored or cause stains. Wipe it immediately. 6) As a glass substrate is used for the TFT-LCD panel, if it is dropped on the floor or hit by something hard, it may be broken or chipped off. 7) Since CMOS LSI is used in this module, take care of static electricity and take the human earth into consideration when handling. 10-5. Others 1) Regarding storage of LCD modules, avoid storing them at direct sunlight-situation. 2) If stored at temperatures below the rated values, the inner liquid crystal may freeze, causing cell destruction. At temperatures exceeding the rated values for storage, the liquid crystal may become isotropic liquid, making it no longer possible to come back to its original state in some cases. 3) If the LCD is broken, do not drink liquid crystal in the mouth. If the liquid crystal adheres to a hand or foot or to clothes, immediately cleanse it with soap. 4) If a water drop or dust adheres to the polarizer, it is apt to cause deterioration. Wipe it immediately. 5) Be sure to observe other caution items for ordinary electronic parts and components. LCY-W-07X04-24 11. Reliability test items No. Test item High temperature storage test 1 Low temperature storage test 2 High temperature 3 & high humidity operation test High temperature operation test 4 (Panel Surface) 5 Low temperature operation test 6 Vibration test (non- operating) 7 Shock test 8 Thermal shock test Conditions Ta = 80C 240h Ta = -30C 240h Ta = 40C ; 95%RH 240h (No condensation) Ta =70C 240h Tp = -20C 240h Frequency range: 10 to 55Hz Stroke: 1.5mm Sweep time: 1minutes Test period: 2 hours for each direction of X,Y,Z Direction: X, Y, Z, Time: Third for each direction. Impact value: 980m/s, Action time 6ms Ta=-20C to 70C /10 cycles (30 min) (30min) NoteTa = Ambient temperature, Tp = Panel temperature Check items In the standard condition, there shall be no practical problems that may affect the display function. 12. Display Grade The standard regarding the grade of color LCD displaying modules should be based on the delivery inspection standard. 13. Delivery Form 13-1. Carton storage conditions 1) Carton piling-up: Max 8 rows 2) Environments Temperature: 040C Humidity: 65% RH or less (at 40C) There should be no dew condensation even at a low temperature and high humidity. 3) Packing form: 15. LCD module packing carton Cartons are weak against damp, and they are apt to be smashed easily due to the compressive pressure applied when piled up. The above environmental conditions of temperature and humidity are set in consideration of reasonable pile-up for storage. LCY-W-07X04-25 14. Lot No. marking The lot No. will be printed on every module by ink-jet. The indication style is shown as below drawing. LQ035Q3DG01 Processing place code (Q, L, etc.) Lot No = Production year(07~) + mouth(A~L) + Serial No(000001~) Model No + Parts code ( - or A ) 15. LCD module packing carton 16. Others 1 Disassembling the module can cause permanent damage and you should be strictly avoided. 2 Please be careful that you don't keep the screen displayed fixed pattern image for a long time, since retention may occur. 3 If you pressed down a liquid crystal display screen with your finger and so on, the alignment disorder of liquid crystal will occur. And then It will become display fault. Therefore, be careful not to touch the screen directly, and to consider not stressing to it. 4 If any problem arises regarding the items mentioned in this specification sheet or otherwise, it should be discussed and settled mutually in a good faith for remedy and/or improvement. LCY-W-07X04-26 17. Outline Dimensions Technical Document LCD Specification LCD Group NORTH AMERICA Sharp Microelectronics of the Americas 5700 NW Pacific Rim Blvd. Camas, WA 98607, U.S.A. Phone: (1) 360-834-2500 Fax: (1) 360-834-8903 www.sharpsma.com TAIWAN Sharp Electronic Components (Taiwan) Corporation 8F-A, No. 16, Sec. 4, Nanking E. Rd. Taipei, Taiwan, Republic of China Phone: (886) 2-2577-7341 Fax: (886) 2-2577-7326/2-2577-7328 CHINA Sharp Microelectronics of China (Shanghai) Co., Ltd. 28 Xin Jin Qiao Road King Tower 16F Pudong Shanghai, 201206 P.R. China Phone: (86) 21-5854-7710/21-5834-6056 Fax: (86) 21-5854-4340/21-5834-6057 Head Office: No. 360, Bashen Road, Xin Development Bldg. 22 Waigaoqiao Free Trade Zone Shanghai 200131 P.R. China Email: smc@china.global.sharp.co.jp EUROPE Sharp Microelectronics Europe Division of Sharp Electronics (Europe) GmbH Sonninstrasse 3 20097 Hamburg, Germany Phone: (49) 40-2376-2286 Fax: (49) 40-2376-2232 www.sharpsme.com JAPAN Sharp Corporation Electronic Components & Devices 22-22 Nagaike-cho, Abeno-Ku Osaka 545-8522, Japan Phone: (81) 6-6621-1221 Fax: (81) 6117-725300/6117-725301 www.sharp-world.com SINGAPORE Sharp Electronics (Singapore) PTE., Ltd. 438A, Alexandra Road, #05-01/02 Alexandra Technopark, Singapore 119967 Phone: (65) 271-3566 Fax: (65) 271-3855 HONG KONG Sharp-Roxy (Hong Kong) Ltd. 3rd Business Division, 17/F, Admiralty Centre, Tower 1 18 Harcourt Road, Hong Kong Phone: (852) 28229311 Fax: (852) 28660779 www.sharp.com.hk Shenzhen Representative Office: Room 13B1, Tower C, Electronics Science & Technology Building Shen Nan Zhong Road Shenzhen, P.R. China Phone: (86) 755-3273731 Fax: (86) 755-3273735 KOREA Sharp Electronic Components (Korea) Corporation RM 501 Geosung B/D, 541 Dohwa-dong, Mapo-ku Seoul 121-701, Korea Phone: (82) 2-711-5813 ~ 8 Fax: (82) 2-711-5819 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited Warranty for SHARP's product warranty. The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or responsible in any way, for any incidental or consequential economic or property damage. LCY-W-07X04