Tektronix Probes, Tracker and Accessories AC Current Probes A6304XL Current Probe c 8 Meter Cable c 500 Amps c DC to 2 MHz The A6304XL is for use with the AM 503B Current Probe Amplifier and is an AC/DC probe with a bandwidth of DC to 2 MHz. The probe is rated for 500 amps continuous and 700 amps peak. It comes with an 8 meter cable and a carrying case. 700-6304. A6304XL ..............................................................................................................EACH 2595.00 1103 Active Probe CT-1 CT-2 c c c c c c c c c c c c c c 25 kHz to 1 GHz Maximum Pulse Current: 12 A Maximum CW Current: 450 mA For 50 1/2 Input AC Only Solid Core ESD Testing 700-6200. CT-1.............................EACH 395.00 1.2 kHz to 200 MHz Maximum Pulse Current: 36 A Maximum CW Current: 2.5 A For 50 1/2 Input AC Only Solid Core Disk Driver Read/Write Signals The 1103 TEKPROBE Power Supply provides power for up to two P6205 Probes or other compatible probes. Also powers ADA400A Active Differential Probe. 700-1103. 1103 .............................................EACH 1295.00 Tektronix TR 210 Huntron Tracker 700-6201. CT-2.............................EACH 389.00 TCP202 DC Coupled Current Probe c c c c c c Probe Connects Directly to TDS Scope through TEKPROBE Interface DC to 50 MHz Bandwidth 15 Amps DC + Peak AC Current 50 Amps Peak Pulse Current 500 106 Amp * Sec Product UL, CSA, CE Marking When combined with a Tektronix TDS oscilloscope, the TCP202 enables users to make direct readout DC and AC current measurements, resulting in accurate displayed and recorded measurements. The TCP202 is a general-purpose probe for displaying and measuring current in electronic circuits. It is ideal for power supply and motor drive design, and for device testing. 700-0202. TCP202 ................................................................................................................EACH 1595.00 Features c Test CMOS and MOS Circuits and PLCs c Ability to Test Components without Power N Ideal for Catastrophic Failures c Ability to Provide a Snapshot of a ComponentOs Overall Health, Including Intermittent Problems c Built-In Pulse Generator to Test Gate-Fired Devices c Non-Destructive Testing Now you can extend the power of your TDS series oscilloscope with the Tektronix TR 210 Huntron Tracker. This remarkable tracker simplifies the testing of newer technology components while giving you a unique current-voltage analog signature that represents the overall health of a tested device. Test Frequencies: 50-60 Hz, 200 Hz, 2 kHz. Functions: Range selection, high range lockout. CompareA-Trace: 0.5-10 Hz. Pulse Level: 0.5-5 V. DC Mode: +DC or DC. Pulse Mode: +Pulse, Pulse or both. Power Requirements: 100 VAC, 115 VAC, 230 VAC; 47-63 Hz. 700-0004. TR 210 ...............................................................................................................EACH 1050.00 Printer, Cart TekTools Accessories A621 1000 Amp AC Current Probe/BNC This industrial style clamp-on probe has a BNC connector and a shrouded banana plug adapter so it can be used on digital multimeters, TekMeter, and scopes. The A621 can measure AC currents from 100 milliamps to 2000 amps peak over a frequency range of 5 Hz to 50 kHz. It provides a 1 mV, 10 mV, or 100 mV output for each amp measured. 700-0640. Model A621 ....................................................................................................................................................................EACH 475.00 A622 100 Amp AC Current Probe/BNC This Olong noseO style clamp-on probe uses a Hall Effect current sensor to provide a voltage output to oscilloscopes. It has a BNC connector and a shrouded banana plug adapter so it can also be used on digital multimeters and TekMeter. The A622 can measure AC/DC currents from 50 mA to 100 amps peak over a frequency range of DC to 100 kHz. It provides 10 mV or 100 mV output for each amp measured. 700-0622. Model A622 ....................................................................................................................................................................EACH 495.00 P5102 High Voltage Probe 100 MHz, high voltage probe for TekScope. Safety certified for up to 1000 volts and with the TekScope, can be floated safely to 600 volts 700-0760. P5102 .............................................................................................................................................................................EACH 250.00 16 THS7CHG Battery Charger Battery charger for the THS7BAT. This will provide a complete recharge in the THS7BAT in less than 2 hours. Also included is an adapter to plug the charger into 12 volt cigarette lighter. 700-0730. THS7CHG........................................................................................................................................................................EACH 325.29 THS7BAT Battery Pack The rechargeable NiCad battery pack is specifically designed for the TekScope. Used with the battery included in the TekScope and the recharger (THS7CHG) the user will always have a charged battery for operation of the TekScope. The battery pack will provide power for TekScope for longer than it takes to recharge the second battery pack. 700-0725. THS7BAT ........................................................................................................................................................................EACH 90.00 THS7HCA Hard Case The hard case is designed for safe transport of the TekScope and has room to also include the HC411 printer, the THS7CHG charger, an extra battery, extra probes, both voltage and current. Safely transport your complete set-up. 700-0735. THS7HCA........................................................................................................................................................................EACH 295.00 ATLDX1 Deluxe Lead Set The deluxe lead set consists of a deluxe plug-on probe set and red and black silicon cables. 700-0400. Model ATLDX1................................................................................................................................................................EACH Same Day Shipments For Product In Stock 80.00 c c c c c c For All Portable Instruments Sturdy and Mobile Platform Enhances Sharing and Work Space Tiltable Top Tray Locking Front Casters Four Outlet U.S. Power Strip Option Low Cost Portability. The K212 column and trays are made from high-strength aluminum; the base is thermoset polyester. Physical Characteristics. Dimensions. Width: Overall Cart N 435 mm/17.0"; Shelf N 407 mm/16.0". Height: Overall Cart N 840 mm/33.0". Depth: Overall Cart N 550 mm/21.6"; Shelf N 352 mm/14.0". Weight: 9 kg; 20 lb. 700-0212. K212...........................................................EACH 479.00 ALLIED c 1013