PUB03CW24 - Carlo Gavazzi Group - Datasheet.Directory

Specifications are subject to change without notice (12.10.06) 1

Monitoring Relays

Product Description Ordering Key

Housing

Function

Type

Item number

Output

Power supply

• TRMS AC/DC over or under voltage

monitoring relays

• Selection of measuring range by DIP-switches

• Adjustable voltage on relative scale

• Adjustable hysteresis on relative scale

• Adjustable delay function (0.1 to 30 s)

•Programmable latching or inhibit at set level

•Output: 8 A SPDT relay N.D. or N.E. selectable

•For mounting on DIN-rail in accordance with

DIN/EN 50 022 (DUB03) or plug-in module (PUB03)

• 22.5 mm Euronorm housing (DUB03)

or 36 mm plug-in module (PUB03)

• LED indication for relay, alarm and power supply ON

Input (voltage level)

DUB03 Terminals A1, A2

PUB03 Terminals 2, 10

Measures on own power

supply

Measuring ranges

Direct Level

Selectable by DIP-switch

24 VAC/DC 10 to 26 V 50 to 110%

48 VAC/DC 10 to 53 V 20 to 110%

115 VAC/DC 12 to 127 V 10 to 110%

240 VAC/DC 24 to 264 V 10 to 110%

The input voltage cannot

raise over 300 VAC/DC

with respect to ground

(PUB03 only)

1-Phase True RMS AC/DC Over or Under Voltage

Types DUB03, PUB03

Input Specifications

DUB 03 C W24

DUB03 and PUB03 are pre-

cise TRMS AC/DC over or

under voltage (selectable by

DIP-switch) monitoring

relays.

Owing to the built-in latch

function, the ON-position of

the relay output can be

maintained. Inhibit function

can be used to avoid relay

operation when not desired

(maintenance, transitions).

The LED's indicate the state

of the alarm and the output

relay.

DUB03 PUB03

Output SPDT relay

Rated insulation voltage 250 VAC

Contact ratings (AgSnO2)µ

Resistive loads AC 1 8A@250 VAC

DC 12 5 A @ 24 VDC

Small inductive loads AC 15 2.5 A @ 250 VAC

DC 13 2.5 A @ 24 VDC

Mechanical life ≥30 x 106operations

Electrical life ≥105operations

(at 8 A, 250 V, cos ϕ=1)

Operating frequency ≤7200 operations/h

Dielectric strength

Dielectric voltage

≥2kVAC (rms)

Rated impulse withstand volt. 4kV (1.2/50 µs)

Output Specifications

Type Selection

Mounting Output Frequency Supply: 12 to 240V AC/DC

DIN-rail SPDT 50 - 400 Hz DUB 03 C W24

Plug-in SPDT 50 - 400 Hz PUB 03 C W24

Power supply Overvoltage cat. III

Rated operational voltage (IEC 60664, IEC 60038)

through terminals:

A1 and A2 (DUB03) or 12 to 240 V AC/DC

2and 10 (PUB03) +10% -15%; 45 to 440 Hz

Dielectric voltage None

Rated operational power 4 VA(AC)

1.5W (DC)

Supply Specifications

2Specifications are subject to change without notice (12.10.06)

DUB03, PUB03

Mode of Operation

DUB03 and PUB03 monitor

both AC and DC over or

under voltage.

Example 1

(latch function disabled, ND

relay)

The relay operates when the

measured value exceeds (or

drops below) the set level for

more than the set delay time.

It releases when the voltage

drops below (or exceeds) the

set level (see hysteresis set-

ting), or when power supply is

interrupted.

Note

If the voltage drops below the

minimum power supply volt-

age and the relay is set for

undervoltage the output con-

tact isn’t necessarily ON.

Example 2

(latch function enabled, NE

relay)

The relay operates and latch-

es in operating position when

the measured value exceeds

(or drops below) the set level

for morethan the set delay

time.

The relay releases when

power supply is interrupted.

The red LED flashes until the

delay time has expired or the

measured value has dropped

below the set point (see hys-

teresis setting).

Power ON delay 1 s ± 0.5 s or 6 s ± 0.5 s

Reaction time (input signal variation from

-20% to +20% or from

+20% to -20% of set value)

Alarm ON delay < 100 ms

Alarm OFF delay < 100 ms

Accuracy (15 min warm-up time)

Temperature drift ± 1000 ppm/°C

Delay ON alarm ± 10% on set value ± 50 ms

Repeatability ± 0.5% on full-scale

Indication for

Power supply ON LED, green

Alarm ON LED, red (flashing 2 Hz

during delay time)

Output relay ON LED, yellow

Environment

Degree of protection IP 20

Pollution degree 3 (DUB03), 2 (PUB03)

Operating temperature -20 to 60°C, R.H. < 95%

Storage temperature -30 to 80°C, R.H. < 95%

General Specifications

Housing

Dimensions DUB03 22.5 x 80 x 99.5 mm

PUB03 36 x 80 x 94 mm

Weight Approx. 150 g

Screw terminals

Tightening torque Max. 0.5 Nm

acc. to IEC 60947

CE Marking Yes

EMC

Electromagnetic Compatibillity

Immunity According to EN 61000-6-2

Emission According to EN 61000-6-3

Adjust the input range set-

ting the DIP switches 1 and

2 as shown below.

Select the desired function

setting the DIP switches 3 to

6as shown below.

To access the DIP switches

open the grey plastic cover

as shown below.

Selection of level and time

delay:

Upper knob:

Setting of hysteresis on rela-

tive scale: 0 to 30% on set

value.

Centre knob:

Voltage level setting on rela-

tive scale: 10 to 110% on

full scale.

Lower knob:

Setting of delay on alarm

time on absolute scale (0.1

to 30 s).

Function/Range/Level and Time Delay Setting

Relay working mode

ON: Normally De-Energized

OFF: Normally Energized

Measuring range

ON OFF 24 V

OFF OFF 48 V

ON ON 115 V

OFF ON 240 V

Power ON delay

ON: 6 s ± 0.5 s

OFF: 1 s ±0.5 s

Contact input

ON: Latching

OFF: Not latching

Monitoring function

ON: Over voltage

OFF: Under voltage

Specifications are subject to change without notice (12.10.06) 3

DUB03, PUB03

N(-)

A2 15

16 18

12-240V

AC/DC(+)

N(-)

10 1

12 - 240V

AC/DC(+)

Wiring Diagrams

DUB03 PUB03

Operation Diagrams

Over voltage - N.D. relay

Under voltage - N.D. relay

Power supply

Set level

Relay ON

Hysteresis

Red LED ON

Power supply

Set level

Relay ON

Hysteresis

Red LED ON

Over voltage - N.E. relay

Under voltage - N.E. relay

Power supply

Set level

Relay ON

Hysteresis

Red LED ON

Power supply

Set level

Relay ON

Hysteresis

Red LED ON

22.5

83.5

99.5

28.5

Dimensions

DIN-rail Plug-in