HV860 Low Noise, Dimmable EL Lamp Driver Features The HV860 has two internal oscillators, a switching MOSFET, and a high voltage EL lamp driver H-bridge. The frequency for the switching MOSFET is set by an external resistor connected between the RSW-Osc pin and the supply pin VDD. The EL lamp driver frequency is set by an external resistor connected between REL-Osc pin and VDD pin. An external inductor is connected between the LX and VDD pins or VIN for split supply applications. A 3.0nF capacitor is connected between CS and ground. The EL lamp is connected between VA and VB. Adjustable output regulation for dimming 220VPP output voltage for higher brightness Single cell lithium ion compatible 150nA shutdown current Separately adjustable lamp and converter frequencies 3x3mm 12-Lead QFN package Split supply capability Applications The switching MOSFET charges the external inductor and discharges it into the capacitor at CS. The voltage at CS will start to increase. Once the voltage at CS reaches a nominal value of 110V, the switching MOSFET is turned OFF to conserve power. The outputs VA and VB are configured as an H bridge and are switching in opposite states to achieve 110V across the EL lamp. Mobile cellular phone keypads PDAs Handheld wireless communication products Global Positioning Systems (GPS) General Description EL lamp dimming can be accomplished by changing the input voltage to the VREG pin. The VREG pin allows an external voltage source to control the VCS amplitude. The VCS voltage is approximately 87 times the voltage seen on VREG. The Supertex HV860 is a high voltage driver designed for driving Electroluminescent, (EL), lamps of up to 5 square inches. The input supply voltage range is from 2.5 to 4.5V. The device uses a single inductor and a minimum number of passive components. Using the internal reference voltage, the regulated output voltage is at a nominal voltage of 110V. The EL lamp will therefore see 110V. An enable pin, (EN), is available to turn the device on and off via a logic signal. Typical Application Circuit VIN CIN LX D RREG VDD CDD 10 RSW 12 1 1.5V = On 0V = Off 2 3 VREG VREF 5 LX CS VDD RSW-Osc VA REL-Osc REL 11 EN GND 4 CS 7 9 VB 8 EL Lamp HV860 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com HV860 Pin Configuration Ordering Information RSW-Osc EN 12-Lead QFN Device 3.00x3.00mm body 0.80mm height (max) 0.50mm pitch HV860 HV860K7-G 12 1 9 VA VREG 2 8 VB VREF 3 7 CS Absolute Maximum Ratings -40C to +85C Storage temperature -65C to +150C Power dissipation: H860 YWLL -0.5V to +120V VREG External input voltage 6 GND LX NC Product Marking 1.6W VCS, Output voltage 5 (top view) Note: Pads are at the bottom of the package. Center heat slug is at ground potential. -0.5V to 6.0V Operating temperature 4 12-Lead QFN (K7) Value VDD, Supply voltage 10 REL-Osc -G indicates package is RoHS compliant (`Green') Parameter 11 VDD 1.33V Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. Continuous operation of the device at the absolute rating level may affect device reliability. All voltages are referenced to device ground. Y = Last Digit of Year Sealed W = Code for Week Sealed L = Lot Number = "Green" Packaging Package may or may not include the following marks: Si or 12-Lead QFN (K7) Thermal Resistance Package ja 12-Lead QFN (K7) 60 C/W Recommended Operating Conditions Sym Parameter Min Typ Max Units VDD Supply voltage 2.5 - 4.5 V --- fSW Switching frequency 40 - 200 kHz --- fEL EL output frequency 150 - 500 Hz --- 0 - 20 nF --- -40 - +85 C --- Min Typ Max Units CLOAD TA EL lamp capacitance load Operating temperature Conditions Electrical Characteristics (Over recommended operating conditions unless otherwise specified TA = 25C) Sym Parameter Conditions RDS(ON) On-resistance of switching transistor - - 6.0 I = 100mA VCS Maximum output regulation voltage 90 - 120 V VDD = 2.5V to 4.5V 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 2 HV860 Electrical Characteristics (cont.) Sym VCS Parameter Min Typ Max - 95 - - 75 - - 55 - 0 - 1.33 V VDD = 2.5 to 4.5V 1.18 1.26 1.33 V VDD = 2.5 to 4.5V Output regulation voltage VREG External input voltage range VREFH VREF output high voltage Units Conditions VDD = 2.5 to 4.5V, VREG = 1.092V V VDD = 2.5 to 4.5V, VREG = 0.862V VDD = 2.5 to 4.5V, VREG = 0.632V IDDQ Quiescent VDD supply current - - 150 nA EN = Low IDD Input current going into the VDD pin - - 250 A VDD = 2.5 to 4.5V, REL = 2.0M, RSW = 1.0M IIN Input current including inductor current - 16 30 mA VIN = 3.0V. See Figure 1. IINQ Quiescent VIN supply current - - 200 nA VIN = 4.2V. EN = Low. See Figure 1. fEL EL lamp frequency 160 200 240 Hz REL = 2.0M fSW Switching transistor frequency 76 90 104 kHz RSW = 1.0M D Switching transistor duty cycle - - 88 % --- VIH Enable input logic high voltage 1.5 - VDD V VDD = 2.5 to 4.5V VIL Enable input logic low voltage 0 - 0.2 V VDD = 2.5 to 4.5V IIH Enable input logic high current - - 100 A VIH = VDD = 2.5 to 4.5V IIL Enable input logic low current - - -1.0 A VIL = 0V, VDD = 2.5 to 4.5V CIN Enable input capacitance - - 15 pF --- Block Diagram LX VDD EN CS Device Enable 100k RSW-Osc PWM Switch Oscillator 0 to 88% + VREG - C 60pF VREF REL-Osc GND VSENSE 1.26V VREF 2x EL Freq. VA Output Drivers VCS VB EL Frequency 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 3 HV860 Figure 1: Typical Application / Test Circuit + - 220H (Cooper Inductor SD3814-221) 4.7F VIN 3.3M 3 2 10 VDD 1.0M 12 0.1F 2.0M 1 1.5V = ON 11 0V = Off VREG VDD 5 VREF BAS21 LX CS RSW-Osc VA REL-Osc EN GND 4 VB 7 3.3nF 200V 9 3.0in2 EL Lamp 8 HV860 Typical Performance VDD 3.0V Lamp Size 3.0in2 VIN IIN 3.3V 19.42mA 3.7V 17.95mA 4.2V 16.02mA VCS fEL Brightness 20.32cd/m2 110V 194Hz 21.40cd/m2 21.81cd/m2 Typical Waveform on VA, VB, and Differential Waveform VA - VB 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 4 HV860 Split Supply Configuration The HV860 can also be used for handheld devices operating from a battery where a regulated voltage is available. This is shown in Figure 2. The regulated voltage can be used to run the internal logic of the HV860. The amount of current necessary to run the internal logic is 250A max. Therefore, the regulated voltage could easily provide the current without being loaded down. Enable/Disable Configuration microprocessor signal is high the device is enabled, and when the signal is low, it is disabled. The HV860 can be easily enabled and disabled via a logic control signal on the EN pin as shown in Figure 2. The control signal can be from a microprocessor. When the Figure 2: Split Supply and Enable/Disable Configuration + - CIN VIN 2 Regulated Voltage = VDD RSW CDD 1 REL 11 On = 1.5V Off = 0V 3 VREG 10 VDD 12 LX RREG D 5 VREF LX CS RSW-Osc VA REL-Osc EN GND 4 Audible Noise Reduction The EL lamp, when lit, emits an audible noise. This is due to EL lamp construction. The audible noise generated by the EL lamp can be a major problem for applications where the EL lamp is held close to the ear, such as cellular phones. VB CS 7 9 EL Lamp 8 HV860 The HV860 employs a proprietary circuit to help minimize the EL lamp's audible noise by using a single resistor, RREG, as shown in Figure 3. Figure 3: Typical Application Circuit for Audible Noise Reduction VIN CIN 2 10 VDD CDD RSW 12 1 1.5V = On 0V = Off REL 11 LX RREG 3 VREG VDD VREF D 5 LX CS RSW-Osc VA REL-Osc EN GND 4 How to Minimize EL Lamp Audible Noise The audible noise from the EL lamp can be minimized with the proper selection of RREG. RREG is connected between the VREF and VREG pins. VREG has an internal 60pF capacitor VB 7 CS 9 8 EL Lamp HV860 to ground. EL lamp noise can be minimized without much loss in brightness by setting the RC time constant to be approximately 1/12 of the EL frequency's period. 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 5 HV860 EL Lamp Dimming using PWM This section describes the method of dimming the EL lamp. Reducing the voltage amplitude at the VREG pin will reduce the voltage on the CS pin, which will effectively reduce the peak to peak voltage the EL lamp sees. Figure 4 shows a circuit to dim the lamp by changing the duty cycle of a PWM signal. A 10k resistor is connected in series with a 3.3M resistor. An N-channel open drain PWM signal is used to pull the 10k resistor to ground. The effective voltage on the VREG pin will be proportional to the duty cycle of the PWM signal. The PWM operating frequency can be anywhere between 20kHz to 100kHz. Figure 4: PWM Dimming Circuit + - VIN 4.7F Open Drain n-channel PWM Signal 3.3M 10k 3 2 + - 10 VDD On = 1.5V Off = 0V 0.1F 220H (Cooper Inductor SD3814-221) VREG VDD 1.0M 12 RSW-Osc 2.0M 1 11 REL-Osc EN 5 VREF GND 4 LX CS VA VB BAS21 7 3.3nF 200V 9 8 EL Lamp HV860 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 6 HV860 Pin Configuration and External Component Description Pin # Name 1 REL-Osc 2 VREG Description External resistor from REL-Osc to VDD sets the EL frequency. The EL frequency is inversely proportional to the external REL resistor value. Reducing the resistor value by a factor of two will result in increasing the EL frequency by two. Input voltage to set VCS regulation voltage. This pin allows an external voltage source to control the VCS amplitude. EL lamp dimming can be accomplished by varying the input voltage at VREG. The VCS voltage is approximately 87 times the voltage seen on VREG. External resistor RREG, connected between VREG and VREF pins controls the VCS charging rate. The charging rate is inversely proportional to the RREG resistor value. 3 VREF Switched internal reference voltage. 4 GND Device ground. Drain of internal switching MOSFET. Connection for an external inductor. 5 LX The inductor LX is used to boost the low input voltage by inductive flyback. When the internal switch is on, the inductor is being charged. When the internal switch is off, the charge stored in the inductor will be transferred to the high voltage capacitor CS. The energy stored in the capacitor is transferred to the internal H-bridge, and therefore to the EL lamp. In general, smaller value inductors, which can handle more current, are more suitable to drive larger size lamps. As the inductor value decreases, the switching frequency of the inductor (controlled by RSW) should be increased to avoid saturation. A 220H Cooper (SD3814-221) inductor with 5.5 series DC resistance is typically recommended. For inductors with the same inductance value, but with lower series DC resistance, lower RSW resistor value is needed to prevent high current draw and inductor saturation. 6 NC No internal connections to the device. 7 CS High voltage regulated output. Connection for an external high voltage capacitor to ground 8 VB VB side of the EL lamp driver H-bridge. Connection for one of the EL lamp terminals. 9 VA VA side of the EL lamp driver H-bridge. Connection for one of the EL lamp terminals. 10 VDD 11 EN Logic input pin. Logic high will enable the device. This pin has an 100k internal pull-down resistor connected to GND. 12 RSW-Osc External resistor from RSW-Osc to VDD sets the switch converter frequency. The switch converter frequency is inversely proportional to the external RSW resistor value. Reducing the resistor value by a factor of two will result in increasing the switch converter frequency by two. Low voltage input supply pin. 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 7 HV860 12-Lead QFN Package Outline (K7) 3.00x3.00mm body, 0.80mm height (max), 0.50mm pitch D2 D 12 1 Note 1 (Index Area D/2 x E/2) 12 1 Note 1 (Index Area D/2 x E/2) e E E2 b View B Top View Bottom View Note 3 A A3 A1 L Seating Plane L1 Note 2 Side View View B Notes: 1. A Pin 1 identifier must be located in the index area indicated. The Pin 1 identifier can be: a molded mark/identifier; an embedded metal marker; or a printed indicator. 2. Depending on the method of manufacturing, a maximum of 0.15mm pullback (L1) may be present. 3. The inner tip of the lead may be either rounded or square. Symbol Dimension (mm) A A1 MIN 0.70 0.00 NOM 0.75 0.02 MAX 0.80 0.05 A3 0.20 REF b D D2 E E2 0.18 2.85* 1.25 2.85* 1.25 0.25 3.00 - 3.00 - 0.30 3.15* 1.65 3.15* 1.65 e 0.50 BSC L L1 0.30 0.00 0O 0.40 - - 0.50 0.15 14O JEDEC Registration MO-220, Variation WEED-5, Issue K, June 2006. * This dimension is not specified in the JEDEC drawing. Drawings not to scale. Supertex Doc. #: DSPD-12QFNK73X3P050, Version B041309. (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to http://www.supertex.com/packaging.html.) Supertex inc. does not recommend the use of its products in life support applications, and will not knowingly sell them for use in such applications unless it receives an adequate "product liability indemnification insurance agreement." Supertex inc. does not assume responsibility for use of devices described, and limits its liability to the replacement of the devices determined defective due to workmanship. No responsibility is assumed for possible omissions and inaccuracies. Circuitry and specifications are subject to change without notice. For the latest product specifications refer to the Supertex inc. website: http//www.supertex.com. (c)2009 All rights reserved. Unauthorized use or reproduction is prohibited. Doc.# DSFP-HV860 C081209 8 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com