Motor driver ICs 3-phase motor driver for CD-ROMs BA6849FP / BA6849FP-Y / BA6849FM / BA6849FS The BA6849 series are ICs developed for CD-ROM spindle motor drives. These ICs possess a short brake and reverserotation brake for two types of brake functions, and also contain FG output and rotation direction detection (FR) circuits, making them high-functionality and high-performance ICs. Applications CD-ROM, CD-R, CD-RW, DVD-ROM, and DVD-RAM Features 1) Three-phase, full-wave, pseudo-linear drive system. 2) Built-in power save and thermal shutdown functions. 3) Built-in current limiter and Hall bias circuits. 4) Built-in FG output. 5) Built-in rotation direction detector. 6) Built-in reverse rotation prevention circuit. 7) Built-in short brake pin. Absolute maximum ratings (Ta = 25C) 863 Motor driver ICs BA6849FP / BA6849FP-Y / BA6849FM / BA6849FS Recommended operating conditions (Ta = 25C) Block diagram 864 Motor driver ICs Pin descriptions BA6849FP / BA6849FM BA6849FP / BA6849FP-Y / BA6849FM / BA6849FS BA6849FP-Y 865 Motor driver ICs MA6849FS 866 BA6849FP / BA6849FP-Y / BA6849FM / BA6849FS Motor driver ICs BA6849FP / BA6849FP-Y / BA6849FM / BA6849FS Input / output circuits (1) Power save (3) Torque output (A1, A2, and A3) (4) Hall input (H1, H1-, H2, H2-, H3, H3-) (2) Torque command input 867 Motor driver ICs BA6849FP / BA6849FP-Y / BA6849FM / BA6849FS (5) Hall bias (7) FR Output (6) FG output (8) Short brake Note: Resistance values are typical values. 868 Motor driver ICs BA6849FP / BA6849FP-Y / BA6849FM / BA6849FS Electrical characteristics (unless otherwise noted, Ta = 25C, VCC = 5V, VM1 = 12V, VM2 = 12V) 869 Motor driver ICs BA6849FP / BA6849FP-Y / BA6849FM / BA6849FS Circuit operation (1) Hall input to coil output The phase relationship between the Hall input signals and the output current and voltage is shown in Fig.9. The motor position data input via the Hall pins is amplified by the Hall amplifier, and formed into waveforms by the matrix block.These signals are input to the output driver that supplies the drive current to the motor coils. 870 Motor driver ICs BA6849FP / BA6849FP-Y / BA6849FM / BA6849FS (2) Torque command The RNF pin voltage with respect to the torque command (EC) is as follows: The I / O gain (GEC) from the EC pin to the RNF pin (output current) is determined by the RNF detector resistor. GEC = 0.255 / RNF [A / V] The torque limit current ITL is given by: ITL = 0.35 / RNF [A] (3) Reverse rotation detection function The reverse detection circuit construction is shown in Fig.11. (1) Forward (EC < ECR) The phase relationship between the Hall input signals H2 and H3 becomes as shown in Fig.9, and the reverse rotation detection circuit does not operate. (2) Reverse (EC > ECR) The phase relationship between the signals H2 and H3 is opposite that for forward operation, and the reverse rotation detection circuit operates. The output goes OFF, and becomes open circuit. 871 Motor driver ICs BA6849FP / BA6849FP-Y / BA6849FM / BA6849FS (4) Short brake When 3.5V or more is applied to the short brake pin, the upper-side output transistors of all go off, and the lowerside output transistors go on. Short braking operates regardless of the torque command signal. Application example 872 (5) Other circuits When 3.5V or more is applied to the power save pin, all circuits are on. When 1.5V or less is applied, the IC enters power save mode. Also, the Hall bias pins turn on and off with the power save pin. Motor driver ICs BA6849FP / BA6849FP-Y / BA6849FM / BA6849FS Operation notes (1) Power save The power save input is an I / O circuit like the own shown in Fig.1. The thermal derating characteristics of the power save pin is -8mV / C, and the resistance will fluctuate between 30% so be careful of the input voltage range. (2) Hall input The input circuit shown in Fig.4 is used for the Hall inputs. The Hall elements can be connected either in series or in parallel. (3) Thermal shutdown (TSD) When the junction temperature reaches 175C, the A1, A2, and A3 coil outputs go open circuit. The thermal shutdown has approximately 15C of hysteresis. Electrical characteristics curves 873 Motor driver ICs External dimensions (Units: mm) 874 BA6849FP / BA6849FP-Y / BA6849FM / BA6849FS Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document use silicon as a basic material. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.0