INCH-POUND
MIL-DTL-55181/1D
10 March 2008
SUPERSEDING
MIL-C-55181/1C
23 June 1986
DETAIL SPECIFICATION SHEET
CONNECTOR, PLUG, ELECTRICAL, WATERPROOF,
4 SOCKET CONTACTS, SOLDER TURRET, 35 AMP
This specification is approved for use by all Departments and Agencies of the Department of Defense.
The requirements for acquiring the product described herein shall consist of this specification sheet and
MIL-DTL-55181.
CONNECTOR
FIGURE 1. Dimensions and configuration.
AMSC N/A FSC 5935
MIL-DTL-55181/1D
2
CONTACT
Inches mm Inches mm Inches mm Inches mm
.015
.028
.038
.040
.041
.042
.044
.048
.052
.062
0.38
0.71
0.96
1.01
1.04
1.06
1.12
1.22
1.32
1.57
.076
.080
.082
.086
.089
.092
.094
.099
.110
.125
1.93
2.03
2.08
2.18
2.26
2.34
2.38
2.51
2.79
3.17
.184
.190
.233
.235
.250
.275
.375
.406
.466
FIGURE 1. Dimensions and configuration - Continued.
.074 1.88 .176 4.47 .470
.513
4.67
4.82
5.92
5.97
6.35
6.99
9.52
10.31
11.83
11.93
13.03
.519
.625
.925
.995
1.000
1.095
1.103
1.470
1.585
2.125
2.500
13.18
15.87
23.49
25.27
25.40
27.81
28.01
37.34
40.26
53.97
63.50
MIL-DTL-55181/1D
3
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for information only.
3. Unless otherwise specified tolerances are ±.005 inch (0.13 mm) for three place decimals and
±.01 inch (0.3 mm) for two place decimals.
4. Angular tolerances are ±30 minutes unless otherwise specified.
5. See table l for cable size accommodations.
FIGURE 1 Dimensions and configuration - Continued.
REQUIREMENTS:
Dimensions and configuration: See figure 1 and table I.
Contacts: 35 ampere current rating, 12 AWG.
Part or Identifying Number (PIN): M55181/1 - (dash number as specified in table I).
TABLE I. Dash number, cross reference and mating connector.
Cable size accommodation Mating connector
PIN
Type designator 1/ MIN MAX PIN Type designator
1/
M55181/1-01
M55181/1-02
M55181/1-03
M55181/1-04
M55181/1-05
MW10F(M)A11
MW10F(M)A13
MW10F(M)A17
MW10F(M)A19
MW10F(M)A15
.292 (7.42)
.323 (8.20)
.448 (11.38)
.511 (12.98)
.386 (9.80)
.343 (8.71)
.406 (10.31)
.531 (13.48)
.593 (15.06)
.468 (11.88)
M55181/2-01
M55181/2-01
M55181/2-01
M55181/2-01
M55181/2-01
MW20M(M)A00
MW20M(M)A00
MW20M(M)A00
MW20M(M)A00
MW20M(M)A00
1/ This type designator shall not be referenced for procurement purposes.
Changes from previous issue. The margins of this specification are marked with vertical lines to indicate
where changes from the previous issue were made. This was done as a convenience only and the
Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and
contractors are cautioned to evaluate the requirements of this document based on the entire content
irrespective of the marginal notations and relationship to the last previous issue.
MIL-DTL-55181/1D
4
CONCLUDING MATERIAL
Custodians: Preparing activity:
Army - CR DLA - CC
Navy - EC
Air Force - 11
DLA - CC (Project 5935-2007-121)
Review activity:
Air Force - 99
NOTE: The activities listed above were interested in this document as of the date of this document. Since
organizations and responsibilities can change, you should verify the currency of the information above
using the ASSIST Online database at http://assist.daps.dla.mil.
