PI74AVC164245 PI74AVC164245A 16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs Features Description IIPI74AVC164245 is designed for low voltage operation: Pericom Semiconductor's PI74AVC164245, a 16-bit (dual-octal) noninverting bus transceiver, contains two separate supply rails: B port (VCCB), set at 3.3V, and A port (VCCA), set to operate at 1.2-2.5V. This arrangement permits translation from a 1.2-2.5V to 3.3V environment and vice versa. 1.2V - 2.5V to 3.3V IIIndustrial operation at -40C to +85C II* Packaging (Pb-free & Green available): - 48-pin plastic 300-mil SSOP (V) - 48-pin plastic 240-mil TSSOP (A) - 48-pin plastic 173-mil TVSOP (K) The PI74AVC164245 is designed for asynchronous communication between data buses. To ensure the high impedance state during power up or power down, the output-enable (OE) input should be tied to VCC through a pullup resistor: the minimum value of the resistor is determined by the current-sinking capability of the driver. Truth Table (each 8-bit section) Inputs Operation OE DIR L L H L H X B data to A bus A data to B bus Isolation Pin Configuration (28-Pin TQFN) Block Diagram 1DIR 1 48 1A1 1OE 47 2 1B1 To Seven Other Channels 2DIR 24 25 2A1 2OE 36 13 2B1 To Seven Other Channels 10-0148 1 (3.3V LVTTL) 1DIR 1 48 1OE (3.3V LVTTL) 1B1 2 47 1A1 1B2 3 46 1A2 GND 4 45 GND 1B3 5 44 1A3 1B4 6 43 1A4 (3.3V) VCCB 7 42 VCCA (1.8V-2.5V) 1B5 8 41 1A5 1B6 9 40 1A6 GND 10 39 GND 1B7 11 38 1A7 1B8 12 37 1A8 2B1 13 36 2A1 2B2 14 35 2A2 GND 15 34 GND 2B3 16 33 2A3 2B4 17 32 2A4 (3.3V) VCCB 18 31 VCCA (1.8V-2.5V) 2B5 19 30 2A5 2B6 20 29 2A6 GND 21 28 GND 2B7 22 27 2A7 2B8 23 26 2A8 (3.3V LVTTL) 2DIR 24 25 2OE (3.3V LVTTL) www.pericom.com P-0.1 04/16/10 PI74AVC164245 16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs Maximum Ratings (Absolute maximum ratings over operating free-air temperature range from VCCB at 3.3V & VCCA at 1.5 - 2.5V, unless otherwise Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Supply Voltage Range VCCA. ...................... -0.5V to 3.8V VCCB....................... -0.5V to 4.6V Continuous output current, IO. ....................................... 50mA Continuous current through each VCC or GND............ 100mA Package thermal impedance, 0JA(3): A package.............. 89C/W K package............................. 58C/W V package............................. 94C/W Storage temperature range, TSTG. ..................... -65C to 150C Input Voltage Range, VI Except I/O ports(1).. -0.5V to 4.6V I/O port A(2)... -0.5V to VCCA+0.5V I/O port B(1)... -0.5V to VCCB+0.5V Input Clamp Current IIK(V1<0)................................. -50mA Ouput Clamp Current IOK(VO<0). ............................ -50mA Recommended Operating Conditions for VCCB at 3.3V(4) Min. Max. 3.0 3.6 Units VCCB Supply voltage VIH High-level voltage VIL Low-level voltage VIB Input Voltage 0 VCCB VOB Output Voltage 0 VCCB IOH High-level output current -12 IOL Low-level output current 12 Dt/Dv Input transition rise or fall rate 10 ns/V TA Operating free-air temperature 85 C 10-0148 2 V 0.8 -40 2 www.pericom.com mA P-0.1 04/16/10 PI74AVC164245 16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs Recommended Operating Conditions for VCCA at 2.5V(4) Min. Max. 2.3 2.7 VCCA Supply voltage VIH High-level voltage VCCA = 2.3V to 2.7V VIL Low-level voltage VCCA = 2.3V to 2.7V VIA Input Voltage 0 VCCA VOA Output Voltage 0 VCCA IOH High-level output current IOL Low-level output current Dt/Dv Input transition rise or fall rate TA Operating free-air temperature Units 1.7 V 0.7 VCCA = 2.3V -8 VCCA = 2.7V -12 VCCA = 2.3V 8 VCCA = 2.7V 12 -40 mA 10 ns/V 85 C Notes: 1. This value is limited to 4.6V maximum. 2. This value is limited to 3.8V maximum. 3. The package thermal impedance is calculated in accordance with JESD 51. 4. To ensure proper device operation, all unused device inputs must be held at the associated VCC or GND. Recommended Operating Conditions for VCCA at 1.8V(4) Min. Max. 1.65 1.95 VCCA Supply voltage VIH High-level voltage VCCA = 1.65V to 1.95V VIL Low-level voltage VCCA = 1.65V to 1.95V VIB Input Voltage 0 VCCA VOA Output Voltage 0 VCCA IOH High-level output current IOL Low-level output current Dt/Dv Input transition rise or fall rate TA Operating free-air temperature Units 0.65 x VCCA 0.35 x VCCA VCCA = 1.65V -4 VCCA = 1.95V -8 VCCA = 1.65V 4 VCCA = 1.95V 8 -40 V mA 10 ns/V 85 C Notes: 1. To ensure proper device operation, all unused device inputs must be held at the associated VCC or GND. 10-0148 3 www.pericom.com P-0.1 04/16/10 PI74AVC164245 16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs Electrical Characteristics (VCCB) (Over recommended operating free-air temperature range for VCCB = 3.3V) Parameter Test Conditions VCCB IOH = -100mA VOH (A to B) IOH = -12mA IOL = -100mA VOL (A to B) IOL = -12mA Min. 3.0V 2.8 3.6V 3.4 3.0V 2.2 3.6V 2.8 Typ. Max. 3.0V 0.2 3.6V 0.2 3.0V 0.5 3.6V 0.5 II Control Inputs VI = VCCB or GND 3.6V 5 IOZ A or B ports VO = VCCB or GND 3.6V 10 ICC VI = VCCB or GND, IO = 0 3.6V 20 DICC* One input at VCCB -0.6V, Other inputs at VCCB or GND 3.0V to 3.6V 500 CI Control Inputs VI = VCCB or GND 3.3V 4.5 CIO A or B ports 3.3V 6.5 VO = VCCB or GND Units V A pF Notes: Typical values are measured at VCC = 3.3V, TA = 25C For I/O ports, the parameter IOZ includes the input leakage current. * This is the increase in supply current for each input that is at one of the specified TTL voltage levels rather than at 0 or the associated VCC. 10-0148 4 www.pericom.com P-0.1 04/16/10 PI74AVC164245 16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs Electrical Characteristics (VCCA) (Over recommended operating free-air temperature range for VCCA = 2.5V) Parameter Test Conditions VCCA VOL (B to A) Typ. Max. Units 2.3V to 2.7V VCC - 0.1 IOH = -100mA VOH (B to A) Min. 2.3V 1.7 IOH = -8mA 2.7V 2.0 IOH = -12mA 2.7V 1.8 IOL = -100mA 2.3V to 2.7V 0.2 IOL = -8mA 2.3V 0.4 IOL = -12mA 2.7V 0.5 V II Control Inputs VI = VCCA or GND 2.7V 5 IOZ A or B ports VO = VCCB or GND 2.7V 10 ICC VI = VCCA or GND, IO = 0 2.7V 30 DICC* One input at VCCA-0.6V, Other inputs at VCCA or GND 2.3V to 2.7V 500 CI Control Inputs VI = VCCA or GND 2.5V 4.5 CIO A or B ports 2.5V 6.5 VO = VCCA or GND A pF Notes: Typical values are measured at VCC = 3.3V, TA = 25C For I/O ports, the parameter IOZ includes the input leakage current. * This is the increase in supply current for each input that is at one of the specified TTL voltage levels rather than at 0 or the associated VCC. 10-0148 5 www.pericom.com P-0.1 04/16/10 PI74AVC164245 16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs Electrical Characteristics (VCCA) (Over recommended operating free-air temperature range for VCCA = 1.8V) Parameter Test Conditions VCCA Min. Typ.** Max. 1.65V to 1.95V VCC - 0.1 1.65V 1.3 1.95V 1.4 IOH = -8mA 1.95V 1.3 IOL = 100mA 1.65V 0.2 IOL = 4mA 1.95V 0.3 IOL = 8mA 1.95V 0.4 VO = VCCA or GND 1.95V 5 ICC VI = VCCA or GND, IO = 0 1.95V 20 DICC* One input at VCCA- 6V, Other inputs at VCCA or GND 1.65V to 1.95V 300 IOH = -100mA VOH (B to A) IOH = -4mA VOL (B to A) IOZ*** A or B ports V CI Control Inputs VI = VCCA or GND 1.8V 4.5 CIO A or B ports 1.8V 6.5 VO = VCCA or GND Units A pF Notes: * The increase in supply current for each input at one of the specified TTL voltage levels rather than at the associated VCC. ** Typical values are measured at VCC = 2.5V or 1.8V, TA = 25C *** For I/O ports, the parameter IOZ includes the input leakage current. 10-0148 6 www.pericom.com P-0.1 04/16/10 PI74AVC164245 16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs Recommended Operating Conditions for VCCA at 1.2V Min. Typ. Max. Units 0.35 x VCCA V VCCA Supply voltage 1.2V VIH High-level voltage VCCA = 1.2V VIL Low-level voltage VCCA = 1.2V VIB Input Voltage 0 VCCA VOA Output Voltage 0 VCCA IOH High-level output current VCCA = 1.2V -2 IOL Low-level output current VCCA = 1.2V 2 Dt/Dv Input transition rise or fall rate TA Operating free-air temperature 0.65 x VCCA -40 mA 10 ns/V 85 C Notes: 1. To ensure proper device operation, all unused device inputs must be held at the associated VCC or GND. Electrical Characteristics (VCCA) (Over recommended operating free-air temperature range for VCCA = 1.2V) Parameter Test Conditions VOH (B to A) VOL (B to A) IOZ** A or B ports ICC VCCA Min. Typ. Max. IOH = -2mA 1.2V 1.1V IOL = 100mA 1.2V 0.1 IOL = 2mA 1.2V 0.1 VO = VCCA or GND 1.2V 5 VI = VCCA or GND, IO = 0 1.2V 10 CI Control Inputs VI = VCCA or GND 1.2V 4.5 CIO A or B ports 1.2V 6.5 VO = VCCA or GND Units A pF Notes: * The increase in supply current for each input at one of the specified TTL voltage levels rather than at the associated VCC. ** For I/O ports, the parameter IOZ includes the input leakage current. 10-0148 7 www.pericom.com P-0.1 04/16/10 PI74AVC164245 16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs Switching Characteristics (CL = see Figures 1,2,3) PI74AVC164245A VCCA = 3.3V 0.3V VCCA = 3.3V 0.3V VCCA = 1.8V 0.15V VCCA = 2.5V 0.2V VCCA = 1.2V VCCA = 1.8V 0.15V VCCA = 2.5V Units 0.2V From (Input) To (Output) Min. Max. Min. Max. Typ. Min. Max. A B 1.5 4.6 1.5 4.2 3.5 1.5 3.5 1.0 3.0 B A 1.5 4.4 1.5 4.0 3.0 1.5 3.5 1.0 2.8 tEN OE B 1.7 5.5 1.7 4.5 2.8 1.7 4.5 1.2 3.5 tDIS OE B 1.5 5.5 1.5 4.5 2.2 1.5 4.5 1.0 3.5 tEN OE A 1.7 5.5 1.7 4.5 4.2 1.7 4.5 1.2 3.5 tDIS OE A 2.0 5.5 2.0 4.5 3.3 2.0 4.5 1.5 3.5 Parameter tPD t PI74AVC164245 (1) SK(O) t (1) SK(b) Min. Max. 0.5 0.3 0.3 0.25 ns Notes: 1. This is the skew between any two outputs of the same package, and switching in the same direction. For tSK(O) ,Output 1 and Output 2 are any two outputs. For tSK(b), Output 1 and Output 2 are on the same bank. Operating Conditions for TA = 25 C VCCA = 2.5V VCCB = 3.3V Test Conditions Typical Outputs Enabled (A or B) CL = 30pF 56 Outputs Disabled F = 10MHz 6 Parameters CPD Power Dissipation Capacitance 10-0148 8 www.pericom.com Units pF P-0.1 04/16/10 PI74AVC164245 16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs Parameter Measurement Information, VCCO = 1.2V VIN From Output Under Test 2 x VCC 2000 Open GND CL = 15pF 2000 Test S1 tPD tPLZ/ tPZL tPHZ/ tPZH Open 2 x VCCO Output Control (low-level enabling) Input tPHL tPLH Output 0V tPZH VOH Output Waveform 2 S1 at GND VCCO/2 VOL VCCO/2 VCCI/2 Output tPZL Waveform 1 S1 at 2xVCCO VCCI VCCI/2 VCCI/2 GND VCCI/2 tPLZ VCCO/2 tPHZ VCCO/2 VCCI 0V VCCO VOL+0.1V VOL VOH VOH -0.1V 0V Voltage Waveforms Enable and Disable Times Figure 1. Load Circuit and Voltage Waveforms Notes: CL includes probe and jig capacitance. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. All input pulses are supplied by generators having the following characteristics: PRR 10Mz, ZO = 50, tR 2.5ns, tF 2.5ns. The outputs are measured one at a time with one transition per measurement. tPLZ and tPHZ are the same as tDIS. tPZL and tPZH are the same as tEN. tPLH and tPHL are the same as tPD. 10-0148 9 www.pericom.com P-0.1 04/16/10 PI74AVC164245 16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs Parameter Measurement Information, VCCO = 1.8V 0.15V VIN From Output Under Test 2 x VCC 1000 Open Test S1 tPD tPLZ/ tPZL tPHZ/ tPZH Open 2 x VCCO GND CL = 30pF 1000 Output Control (low-level enabling) VCCI Input VCCI/2 VCCI/2 tPHL tPLH Output VCCI/2 VCCO/2 tPZH tPHZ Output Waveform 2 S1 at GND VCCO/2 VOL VCCO/2 VCCI VCCI/2 Output tPZL Waveform 1 S1 at 2xVCCO 0V VOH GND tPLZ VCCO/2 0V VCCO VOL+0.15V VOL VOH VOH -0.15V 0V Voltage Waveforms Enable and Disable Times Figure 1. Load Circuit and Voltage Waveforms Notes: CL includes probe and jig capacitance. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. All input pulses are supplied by generators having the following characteristics: PRR 10Mz, ZO = 50, tR 2.5ns, tF 2.5ns. The outputs are measured one at a time with one transition per measurement. tPLZ and tPHZ are the same as tDIS. tPZL and tPZH are the same as tEN. tPLH and tPHL are the same as tPD. 10-0148 10 www.pericom.com P-0.1 04/16/10 PI74AVC164245 16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs Parameter Measurement Information, VCCO = 2.5V 0.2V VIN From Output Under Test 2 x VCC 500 Open Test S1 tPD tPLZ/ tPZL tPHZ/ tPZH Open 2 x VCCO GND CL = 30pF 500 Output Control (low-level enabling) VCCI/2 VCCI/2 tPHL tPLH Output 0V tPZH VOH Output Waveform 2 S1 at GND VCCO/2 VOL VCCO/2 VCCI VCCI/2 VCCI/2 Output tPZL Waveform 1 S1 at 6V VCCI Input GND tPLZ VCCO/2 tPHZ VCCO/2 0V VCCO VOL+0.2V VOL VOH VOH -0.2V 0V Voltage Waveforms Enable and Disable Times Figure 1. Load Circuit and Voltage Waveforms Notes: CL includes probe and jig capacitance. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. All input pulses are supplied by generators having the following characteristics: PRR 10Mz, ZO = 50, tR 2.5ns, tF 2.5ns. The outputs are measured one at a time with one transition per measurement. tPLZ and tPHZ are the same as tDIS. tPZL and tPZH are the same as tEN. tPLH and tPHL are the same as tPD. 10-0148 11 www.pericom.com P-0.1 04/16/10 PI74AVC164245 16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs Parameter Measurement Information, VCCO = 3.3V 0.3V VIN From Output Under Test 500 S1 6V Open Test S1 tPD tPLZ/ tPZL tPHZ/ tPZH Open 2 x VCCO GND CL = 30pF 500 Output Control (low-level enabling) VCCI/2 VCCI/2 tPHL tPLH Output VCCO/2 VCCI VCCI/2 Output tPZL Waveform 1 S1 2 x VCCO VCCA Input 0V tPZH VOH Output Waveform 2 S1 at GND VCCO/2 VOL GND VCCI/2 tPLZ VCCO/2 tPHZ VCCO/2 0V VCCI VOL+0.3V VOL VOH VOH -0.3V 0V Voltage Waveforms Enable and Disable Times Figure 1. Load Circuit and Voltage Waveforms Notes: CL includes probe and jig capacitance. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. All input pulses are supplied by generators having the following characteristics: PRR 10Mz, ZO = 50, tR 2.5ns, tF 2.5ns. The outputs are measured one at a time with one transition per measurement. tPLZ and tPHZ are the same as tDIS. tPZL and tPZH are the same as tEN. tPLH and tPHL are the same as tPD. 10-0148 12 www.pericom.com P-0.1 04/16/10 PI74AVC164245 16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs Packaging Mechanical: 48-Pin TSSOP (A) DOCUMENT CONTROL NO. PD - 1501 48 REVISION: G DATE: 03/09/05 .236 .244 6.0 6.2 See Note 4 1 .488 12.4 .496 12.6 See Note 3 .047 1.20 Max SEATING PLANE 1 .004 0.09 .008 0.20 X.XX X.XX DENOTES DIMENSIONS IN MILLIMETERS .0197 BSC 0.50 .002 .006 0.05 0.15 .007 .010 0.17 0.27 Note: 1. Controlling dimensions in millimeters. 2. Ref: JEDEC MO-153F/ED 3. Dimension does not include mold flash, protrusions or gate burrs. Mold flash, protrusions and gate burrs shall not exceed 0.15mm per side. 4. Dimension does not include interlead flash or protrusion. Interlead flash or protrusion shall not exceed 0.25mm per side. 0.45 .018 0.75 .030 .319 BSC 8.1 Pericom Semiconductor Corporation 3545 N. 1st Street, San Jose, CA 95134 1-800-435-2335 * www.pericom.com DESCRIPTION: 48-Pin 240-Mil Wide TSSOP PACKAGE CODE: A Pericom Semiconductor Corporation * 1-800-435-2336 10-0148 13 www.pericom.com P-0.1 04/16/10 PI74AVC164245 16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs Packaging Mechanical: 48-Pin TSSOP (V) DOCUMENT CONTROL NO. PD - 1401 48 REVISION: E DATE: 03/09/05 .291 .299 7.39 7.59 .395 .420 10.03 10.67 Gauge Plane .010 0.25 .02 0.51 .04 1.01 1 .015 0.381 x 45 .025 0.635 .008 0.20 Nom. 1 .620 .630 15.75 16.00 .110 2.79 Max .008 0.20 .016 0.40 0-8 .025 BSC 0.635 .008 0.20 .0135 0.34 X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS Pericom Semiconductor Corporation 3545 N. 1st Street, San Jose, CA 95134 1-800-435-2335 * www.pericom.com Notes: 1) Controlling dimensions in inches. 2) Ref: JEDEC MO-118B/AA DESCRIPTION: 48-Pin, 300-Mil Wide, SSOP PACKAGE CODE: V 10-0148 14 www.pericom.com P-0.1 04/16/10 PI74AVC164245 16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs Packaging Mechanical: 48-Pin TSSOP (K) 1 DATE: 08/29/08 DESCRIPTION: 48-Pin, 173mil wide TVSOP (TSSOP) PACKAGE CODE: K48 REVISION: D DOCUMENT CONTROL #: PD-1324 08-0442 Ordering Information Ordering Code Package Code Speed Grade Package Description PI74AVC164245VE V Blank Pb-free & Green, 48-pin 300-mil wide plastic SSOP PI74AVC164245AE A Blank Pb-free & Green, 48-pin 240-mil wide plastic TSSOP PI74AVC164245KE K Blank Pb-free & Green, 48-pin 173-mil wide plastic TVSOP PI74AVC164245AVE V A Pb-free & Green, 48-pin 300-mil wide plastic SSOP PI74AVC164245AAE A A Pb-free & Green, 48-pin 240-mil wide plastic TSSOP Notes: 1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ 2. E = Pb-free and Green 3. X Suffix =Tape/Reel 10-0148 15 www.pericom.com P-0.1 04/16/10