LM4929
www.ti.com
SNAS293B DECEMBER 2004REVISED APRIL 2013
LM4929 Boomer™ Audio Power Amplifier Series Stereo 40mW Low Noise Headphone
Amplifier with OCL Output
Check for Samples: LM4929
1FEATURES DESCRIPTION
The LM4929 is an stereo audio power amplifier
23 OCL outputs No DC Blocking Capacitors capable of delivering 40mW per channel of
External Gain-Setting Capability continuous average power into a 16load or 25mW
Available in Space-Saving VSSOP Package per channel into a 32load at 1% THD+N from a 3V
power supply.
Ultra Low Current Shutdown Mode
2V - 5.5V Operation Boomer audio power amplifiers were designed
specifically to provide high quality output power with a
Ultra Low Noise minimal amount of external components. Since the
LM4929 does not require bootstrap capacitors or
APPLICATIONS snubber networks, it is optimally suited for low-power
Portable CD players portable systems. The LM4929 is configured for OCL
(Output Capacitor-Less) outputs, operating with no
PDAs DC blocking capacitors on the outputs.
Portable Electronics Devices The LM4929 features a low-power consumption
shutdown mode with a faster turn on time.
KEY SPECIFICATIONS Additionally, the LM4929 features an internal thermal
PSRR at 217Hz and 1kHz shutdown protection mechanism.
Output Power at 1kHz with VDD = 2.4V, The LM4929 is unity gain stable and may be
1% THD+N into a 16load, 65dB (Typ) configured with external gain-setting resistors.
Output Power at 1kHz with VDD = 3V,
1% THD+N into a 16load, 25 mW (Typ)
Shutdown current, 40 mW (Typ), 2.0µA (Max)
Output Voltage change on release
from Shutdown VDD = 2.4V, RL= 16, 1mV
(Max)
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2Boomer is a trademark of Texas Instruments.
3All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 2004–2013, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
OUT A
OUT C
OUT B
+
-
Bias
Generator
Click-Pop
and
SD Control
Logic
+
-
+
-
IN A
IN B
CBYPASS
SD
LM4929
SNAS293B DECEMBER 2004REVISED APRIL 2013
www.ti.com
Block Diagram
Figure 1. Block Diagram
Typical Application
Figure 2. Typical OCL Output Configuration Circuit
2Submit Documentation Feedback Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM4929
1
2
3
4
56
7
8
9
10
IN A
SD
NC
BYP
IN B
VDD
VoA
VoC
VoB
GND
LM4929
www.ti.com
SNAS293B DECEMBER 2004REVISED APRIL 2013
Connection Diagram
Figure 3. VSSOP Package
Top View
See NS Package Number DGS
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings(1)(2)(3)
Supply Voltage 6.0V
Storage Temperature 65°C to +150°C
Input Voltage(4) -0.3V to VDD + 0.3V
Power Dissipation(5) Internally Limited
ESD Susceptibility(6) 2000V
ESD Susceptibility(7) 200V
Junction Temperature 150°C
θJC (VSSOP) 56°C/W
Thermal Resistance θJA (VSSOP) 190°C/W
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication
of device performance.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
(3) Datasheet min/max specification limits are ensured by design, test, or statistical analysis.
(4) 10Terminated input.
(5) The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, θJA, and the ambient
temperature, TA. The maximum allowable power dissipation is PDMAX = (TJMAX - TA)/ θJA or the number given in Absolute Maximum
Ratings, whichever is lower. For the LM4929, see power derating currents for more information.
(6) Human body model, 100pF discharged through a 1.5kresistor.
(7) Machine Model, 220pF-240pF discharged through all pins.
Operating Ratings
Temperature Range TMIN TATMAX 40°C TA85°C
Supply Voltage 2V VDD 5.5V
Copyright © 2004–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM4929
LM4929
SNAS293B DECEMBER 2004REVISED APRIL 2013
www.ti.com
Electrical Characteristics VDD = 5V(1)(2)
The following specifications apply for VDD = 5V, RL= 16, and CB= 4.7µF unless otherwise specified. Limits apply to TA=
25°C. Pin 3 connected to GND(3).
Symbol Parameter Conditions LM4929 Units
(Limits)
Typ(4) Limit(5)
IDD Quiescent Power Supply Current VIN = 0V, IO= 0A 2 5 mA (max)
ISD Shutdown Current VSHUTDOWN = GND 0.1 2.0 µA(max)
VSDIH Shutdown Voltage Input High 1.8 V
VSDIL Shutdown Voltage Input Low 0.4 V
THD = 1%; f = 1 kHZ
POOutput Power RL= 1680 mW
RL= 3280
VNO Output Noise Voltage BW = 20Hz to 20kHz, A-weighted 10 µV
PSRR Power Supply Rejection Ratio VRIPPLE = 200mV sine p-p 65 dB
(1) All voltages are measured with respect to the GND pin unless otherwise specified.
(2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication
of device performance.
(3) Pin 3 (NC) should be connected to GND for proper part operation.
(4) Typicals are measured at 25°C and represent the parametric norm.
(5) Limits are specified to Texas Instruments' AOQL (Average Outgoing Quality Level).
Electrical Characteristics VDD = 3.0V(1)(2)
The following specifications apply for VDD = 3.0V, RL= 16, and CB= 4.7µF unless otherwise specified. Limits apply to TA=
25°C. Pin 3 connected to GND(3).
Symbol Parameter Conditions LM4929 Units
(Limits)
Typ(4) Limit(5)
IDD Quiescent Power Supply Current VIN = 0V, IO= 0A 1.5 3.5 mA (max)
ISD Shutdown Current VSHUTDOWN = GND 0.1 2.0 µA(max)
THD = 1%; f = 1kHz
POOutput Power R = 1640 mW
R = 3225
VNO Output Noise Voltage BW = 20 Hz to 20kHz, A-weighted 10 µV
PSRR Power Supply Rejection Ratio VRIPPLE = 200mV sine p-p 65 dB
(1) All voltages are measured with respect to the GND pin unless otherwise specified.
(2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication
of device performance.
(3) Pin 3 (NC) should be connected to GND for proper part operation.
(4) Typicals are measured at 25°C and represent the parametric norm.
(5) Limits are specified to Texas Instruments' AOQL (Average Outgoing Quality Level).
4Submit Documentation Feedback Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM4929
LM4929
www.ti.com
SNAS293B DECEMBER 2004REVISED APRIL 2013
Electrical Characteristics VDD = 2.4V(1)(2)
The following specifications apply for VDD = 2.4V, RL= 16, and CB= 4.7µF unless otherwise specified. Limits apply to TA=
25°C. Pin 3 connected to GND(3).
Symbol Parameter Conditions LM4929 Units
(Limits)
Typ(4) Limit(5)
IDD Quiescent Power Supply Current VIN = 0V, IO= 0A 1.5 3 mA (max)
ISD Shutdown Current VSHUTDOWN = GND 0.1 2.0 µA(max)
THD = 1%; f = 1kHz
POOutput Power R = 1625 mW
R = 3212
VNO Output Noise Voltage BW = 20 Hz to 20kHz, A-weighted 10 µV
PSRR Power Supply Rejection Ratio VRIPPLE = 200mV sine p-p 65 dB
TWU Wake Up Time from Shutdown OCL 0.5 s
(1) All voltages are measured with respect to the GND pin unless otherwise specified.
(2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication
of device performance.
(3) Pin 3 (NC) should be connected to GND for proper part operation.
(4) Typicals are measured at 25°C and represent the parametric norm.
(5) Limits are specified to Texas Instruments' AOQL (Average Outgoing Quality Level).
External Components Description
See Figure 2
Components Functional Description
1. RIInverting input resistance which sets the closed-loop gain in conjunction with Rf. This resistor also forms a high-pass
filter with Ciat fc= 1/(2πRiCi).
2. CIInput coupling capacitor which blocks the DC voltage at the amplifier's input terminals. Also creates a high-pass filter
with Riat fc= 1/(2πRiCi). Refer to the section PROPER SELECTION OF EXTERNAL COMPONENTS for an
explanation of how to determine the value of Ci.
3. RfFeedback resistance which sets the closed-loop gain in conjunction with Ri.
4. CSSupply bypass capacitor which provides power supply filtering. Refer to the POWER SUPPLY BYPASSING section for
information concerning proper placement and selection of the supply bypass capacitor.
5. CBBypass pin capacitor which provides half-supply filtering. Refer to the section, PROPER SELECTION OF EXTERNAL
COMPONENTS, for information concerning proper placement and selection of CB
Copyright © 2004–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM4929
LM4929
SNAS293B DECEMBER 2004REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics
THD+N vs Frequency THD+N vs Frequency
Figure 4. Figure 5.
THD+N vs Frequency THD+N vs Frequency
Figure 6. Figure 7.
THD+N vs Frequency THD+N vs Frequency
Figure 8. Figure 9.
6Submit Documentation Feedback Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM4929
LM4929
www.ti.com
SNAS293B DECEMBER 2004REVISED APRIL 2013
Typical Performance Characteristics (continued)
THD+N vs Output Power THD+N vs Output Power
Figure 10. Figure 11.
Output Power vs Load Resistance Output Power vs Supply Voltage
Figure 12. Figure 13.
Output Power vs Supply Voltage Output Power vs Load Resistance
Figure 14. Figure 15.
Copyright © 2004–2013, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM4929
LM4929
SNAS293B DECEMBER 2004REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics (continued)
Power Supply Rejection Ratio Power Supply Rejection Ratio
Figure 16. Figure 17.
Frequency Response vs
Input Capacitor Size Open Loop Frequency Response
Figure 18. Figure 19.
Supply Voltage vs Clipping Voltage vs
Supply Current Supply Voltage
Figure 20. Figure 21.
8Submit Documentation Feedback Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM4929
0 10 30 60
0
40
140
POWER DISSIPATION (mW)
OUTPUT POWER (mW)
RL = 16:
RL = 32:
60
100
120
4020 50
20
80
1m 10m 20m 100m
0.001
0.01
0.1
10
THD+N (%)
OUTPUT POWER (W)
1
1 kHz
20 Hz
20 kHz
0 50 100 200
0
50
100
500
POWER DISSIPATION (mW)
OUTPUT POWER (mW)
150
RL = 16:
RL = 32:
200
250
300
350
400
450
150
0 10 30 90
0
40
200
POWER DISSIPATION (mW)
OUTPUT POWER (mW)
RL = 16:
RL = 32:
80
120
160
4020 50 60 70 80
LM4929
www.ti.com
SNAS293B DECEMBER 2004REVISED APRIL 2013
Typical Performance Characteristics (continued)
Shutdown Hysteresis Voltage, VDD = 5V Shutdown Hysteresis Voltage, VDD = 3V
Figure 22. Figure 23.
Power Dissipation vs Output Power Power Dissipation vs Output Power
VDD = 5V VDD = 3V
Figure 24. Figure 25.
Power Dissipation vs Output Power THD+N vs Output Power
VDD = 2.4V VDD = 3V, RL= 32
Figure 26. Figure 27.
Copyright © 2004–2013, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM4929
0 20 60 160
0
0.2
0.6
POWER DISSIPATION (W)
AMBIENT TEMPERATURE (°C)
0.3
0.5
8040 100
0.1
0.4
120 140
1m 10m 20m 100m
0.001
0.01
0.1
10
THD+N (%)
OUTPUT POWER (W)
1
1 kHz
20 Hz
20 kHz
1m 10m 20m 100m
0.001
0.01
0.1
10
THD+N (%)
OUTPUT POWER (W)
1
1 kHz
20 Hz
20 kHz
1m 10m 20m 100m
0.001
0.01
0.1
10
THD+N (%)
OUTPUT POWER (W)
1
1 kHz
20 Hz
20 kHz
LM4929
SNAS293B DECEMBER 2004REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics (continued)
THD+N vs Output Power THD+N vs Output Power
VDD = 2.4V, RL= 32VDD = 3V, RL= 16
Figure 28. Figure 29.
THD+N vs Output Power
VDD = 2.4V, RL= 16Power Derating Curve
Figure 30. Figure 31.
10 Submit Documentation Feedback Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM4929
LM4929
www.ti.com
SNAS293B DECEMBER 2004REVISED APRIL 2013
APPLICATION INFORMATION
AMPLIFIER CONFIGURATION EXPLANATION
As shown in Figure 1, the LM4929 has three operational amplifiers internally. Two of the amplifier's have
externally configurable gain while the other amplifier is internally fixed at the bias point acting as a unity-gain
buffer. The closed-loop gain of the two configurable amplifiers is set by selecting the ratio of Rfto Ri.
Consequently, the gain for each channel of the IC is
AVD = -(Rf/ Ri) (1)
By driving the loads through outputs VoA and VoB with VoC acting as a buffered bias voltage the LM4929 does
not require output coupling capacitors. The classical single-ended amplifier configuration where one side of the
load is connected to ground requires large, expensive output coupling capacitors.
A configuration such as the one used in the LM4929 has a major advantage over single supply, single-ended
amplifiers. Since the outputs VoA, VoB, and VoC are all biased at 1/2 VDD, no net DC voltage exists across each
load. This eliminates the need for output coupling capacitors which are required in a single-supply, single-ended
amplifier configuration. Without output coupling capacitors in a typical single-supply, single-ended amplifier, the
bias voltage is placed across the load resulting in both increased internal IC power dissipation and possible
loudspeaker damage.
The LM4929 eliminates these output coupling capacitors by running in OCL mode. Unless shorted to ground,
VoC is internally configured to apply a 1/2 VDD bias voltage to a stereo headphone jack's sleeve. This voltage
matches the bias voltage present on VoA and VoB outputs that drive the headphones. The headphones operate
in a manner similar to a bridge-tied load (BTL). Because the same DC voltage is applied to both headphone
speaker terminals this results in no net DC current flow through the speaker. AC current flows through a
headphone speaker as an audio signal's output amplitude increases on the speaker's terminal.
The headphone jack's sleeve is not connected to circuit ground when used in OCL mode. Using the headphone
output jack as a line-level output will place the LM4929's 1/2 VDD bias voltage on a plug's sleeve connection. This
presents no difficulty when the external equipment uses capacitively coupled inputs. For the very small minority
of equipment that is DC coupled, the LM4929 monitors the current supplied by the amplifier that drives the
headphone jack's sleeve. If this current exceeds 500mAPK, the amplifier is shutdown, protecting the LM4929 and
the external equipment.
POWER DISSIPATION
Power dissipation is a major concern when using any power amplifier and must be thoroughly understood to
ensure a successful design. When operating in capacitor-coupled mode, Equation 2 states the maximum power
dissipation point for a single-ended amplifier operating at a given supply voltage and driving a specified output
load. PDMAX = (VDD)2/ (2π2RL) (2)
Since the LM4929 has three operational amplifiers in one package, the maximum power dissipation increases
due to the use of the third amplifier as a buffer and is given in Equation 3:
PDMAX = 4(VDD)2/ (2π2RL) (3)
The maximum power dissipation point obtained from Equation 3 must not be greater than the power dissipation
that results from Equation 4:
PDMAX = (TJMAX - TA) / θJA (4)
For package DGS, θJA = 190°C/W. TJMAX = 150°C for the LM4929. Depending on the ambient temperature, TA,
of the system surroundings, Equation 4 can be used to find the maximum internal power dissipation supported by
the IC packaging. If the result of Equation 3 is greater than that of Equation 4, then either the supply voltage
must be decreased, the load impedance increased or TAreduced. For the typical application of a 3V power
supply, with a 32load, the maximum ambient temperature possible without violating the maximum junction
temperature is approximately 144°C provided that device operation is around the maximum power dissipation
point. Thus, for typical applications, power dissipation is not an issue. Power dissipation is a function of output
power and thus, if typical operation is not around the maximum power dissipation point, the ambient temperature
may be increased accordingly. Refer to the Typical Performance Characteristics for power dissipation information
for lower output powers.
Copyright © 2004–2013, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM4929
LM4929
SNAS293B DECEMBER 2004REVISED APRIL 2013
www.ti.com
POWER SUPPLY BYPASSING
As with any amplifier, proper supply bypassing is important for low noise performance and high power supply
rejection. The capacitor location on the power supply pins should be as close to the device as possible.
Typical applications employ a 3V regulator with 10mF tantalum or electrolytic capacitor and a ceramic bypass
capacitor which aid in supply stability. This does not eliminate the need for bypassing the supply nodes of the
LM4929. A bypass capacitor value in the range of 0.1µF to F is recommended for CS.
MICRO POWER SHUTDOWN
The voltage applied to the SHUTDOWN pin controls the LM4929's shutdown function. Activate micro-power
shutdown by applying a logic-low voltage to the SHUTDOWN pin. When active, the LM4929's micro-power
shutdown feature turns off the amplifier's bias circuitry, reducing the supply current. The trigger point varies
depending on supply voltage and is shown in the Shutdown Hysteresis Voltage graphs in the Typical
Performance Characteristics section. The low 0.1µA(typ) shutdown current is achieved by applying a voltage that
is as near as ground as possible to the SHUTDOWN pin. A voltage that is higher than ground may increase the
shutdown current. There are a few ways to control the micro-power shutdown. These include using a single-pole,
single-throw switch, a microprocessor, or a microcontroller. When using a switch, connect an external 100k
pull-up resistor between the SHUTDOWN pin and VDD. Connect the switch between the SHUTDOWN pin and
ground. Select normal amplifier operation by opening the switch. Closing the switch connects the SHUTDOWN
pin to ground, activating micro-power shutdown.
The switch and resistor ensure that the SHUTDOWN pin will not float. This prevents unwanted state changes. In
a system with a microprocessor or microcontroller, use a digital output to apply the control voltage to the
SHUTDOWN pin. Driving the SHUTDOWN pin with active circuitry eliminates the pull-up resistor.
Shutdown enable/disable times are controlled by a combination of CBand VDD. Larger values of CBresults in
longer turn on/off times from Shutdown. Smaller VDD values also increase turn on/off time for a given value of CB.
Longer shutdown times also improve the LM4929's resistance to click and pop upon entering or returning from
shutdown. For a 2.4V supply and CB= 4.7µF, the LM4929 requires about 2 seconds to enter or return from
shutdown. This longer shutdown time enables the LM4929 to have virtually zero pop and click transients upon
entering or release from shutdown.
Smaller values of CBwill decrease turn-on time, but at the cost of increased pop and click and reduced PSRR.
Since shutdown enable/disable times increase dramatically as supply voltage gets below 2.2V, this reduced turn-
on time may be desirable if extreme low supply voltage levels are used as this would offset increases in turn-on
time caused by the lower supply voltage. This technique is not recommended for OCL mode since shutdown
enable/disable times are very fast (0.5s) independent of supply voltage.
PROPER SELECTION OF EXTERNAL COMPONENTS
Proper selection of external components in applications using integrated power amplifiers is critical to optimize
device and system performance. While the LM4929 is tolerant of external component combinations,
consideration to component values must be used to maximize overall system quality.
The LM4929 is unity-gain stable which gives the designer maximum system flexibility. The LM4929 should be
used in low gain configurations to minimize THD+N values, and maximize the signal to noise ratio. Low gain
configurations require large input signals to obtain a given output power. Input signals equal to or greater than
1Vrms are available from sources such as audio codecs. Very large values should not be used for the gain-setting
resistors. Values for Riand Rfshould be less than 1M. Please refer to the section, AUDIO POWER AMPLIFIER
DESIGN, for a more complete explanation of proper gain selection
Besides gain, one of the major considerations is the closed-loop bandwidth of the amplifier. To a large extent, the
bandwidth is dictated by the choice of external components shown in Figure 2. The input coupling capacitor, Ci,
forms a first order high pass filter which limits low frequency response. This value should be chosen based on
needed frequency response and turn-on time.
SELECTION OF INPUT CAPACITOR SIZE
Amplifying the lowest audio frequencies requires a high value input coupling capacitor, Ci. A high value capacitor
can be expensive and may compromise space efficiency in portable designs. In many cases, however, the
headphones used in portable systems have little ability to reproduce signals below 60Hz. Applications using
headphones with this limited frequency response reap little improvement by using a high value input capacitor.
12 Submit Documentation Feedback Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM4929
LM4929
www.ti.com
SNAS293B DECEMBER 2004REVISED APRIL 2013
In addition to system cost and size, turn on time is affected by the size of the input coupling capacitor Ci. A larger
input coupling capacitor requires more charge to reach its quiescent DC voltage. This charge comes from the
output via the feedback Thus, by minimizing the capacitor size based on necessary low frequency response,
turn-on time can be minimized. A small value of Ci(in the range of 0.1µF to 0.39µF), is recommended.
AUDIO POWER AMPLIFIER DESIGN
A 25mW/32AUDIO AMPLIFIER
Given:
Power Output 25mWrms
Load Impedance 32
Input Level 1Vrms
Input Impedance 20k
A designer must first determine the minimum supply rail to obtain the specified output power. By extrapolating
from the Output Power vs Supply Voltage graphs in the Typical Performance Characteristics section, the supply
rail can be easily found.
3V is a standard voltage in most applications, it is chosen for the supply rail. Extra supply voltage creates
headroom that allows the LM4929 to reproduce peak in excess of 25mW without producing audible distortion. At
this time, the designer must make sure that the power supply choice along with the output impedance does not
violate the conditions explained in the POWER DISSIPATION section.
Once the power dissipation equations have been addressed, the required gain can be determined from
Equation 5.
(5)
From Equation 5, the minimum AVis 0.89; use AV= 1. Since the desired input impedance is 20k, and with a AV
gain of 1, a ratio of 1:1 results from Equation 1 for Rfto Ri. The values are chosen with Ri= 20kand Rf= 20k.
The final design step is to address the bandwidth requirements which must be stated as a pair of -3dB frequency
points. Five times away from a -3dB point is 0.17dB down from passband response which is better than the
required ± 0.25dB specified.
fL= 100Hz/5 = 20Hz
fH= 20kHz * 5 = 100kHz
As stated in the External Components section, Riin conjunction with Cicreates a
Ci1 / (2π* 20k* 20Hz) = 0.397µF; use 0.39µF.
The high frequency pole is determined by the product of the desired frequency pole, fH, and the differential gain,
AV. With an AV= 1 and fH= 100kHz, the resulting GBWP = 100kHz which is much smaller than the LM4929
GBWP of 10MHz. This figure displays that is a designer has a need to design an amplifier with higher differential
gain, the LM4929 can still be used without running into bandwidth limitations.
Figure 32 shows an optional resistor connected between the amplifier output that drives the headphone jack
sleeve and ground. This resistor provides a ground path that supressed power supply hum. Thishum may occur
in applications such as notebook computers in a shutdown condition and connected to an external powered
speaker. The resistor's 100value is a suggested starting point. Its final value must be determined based on the
tradeoff between the amount of noise suppression that may be needed and minimizing the additional current
drawn by the resistor (25mA for a 100resistor and a 5V supply).
ESD PROTECTION
As stated in the Absolute Maximum Ratings, the LM4929 has a maximum ESD susceptibility rating of 2000V. For
higher ESD voltages, the addition of a PCDN042 dual transil (from California Micro Devices), as shown in
Figure 32, will provide additional protection.
Copyright © 2004–2013, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM4929
LM4929
SNAS293B DECEMBER 2004REVISED APRIL 2013
www.ti.com
Figure 32. The PCDN042 provides additional ESD protection beyond the 2000V shown in the
Absolute Maximum Ratings for the VOC output
14 Submit Documentation Feedback Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LM4929
LM4929
www.ti.com
SNAS293B DECEMBER 2004REVISED APRIL 2013
REVISION HISTORY
Changes from Revision A (April 2013) to Revision B Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 14
Copyright © 2004–2013, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LM4929
PACKAGE OPTION ADDENDUM
www.ti.com 27-Mar-2017
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM4929MMX/NOPB ACTIVE VSSOP DGS 10 3500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 GB9
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
PACKAGE OPTION ADDENDUM
www.ti.com 27-Mar-2017
Addendum-Page 2
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM4929MMX/NOPB VSSOP DGS 10 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 12-Aug-2013
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM4929MMX/NOPB VSSOP DGS 10 3500 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 12-Aug-2013
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Texas Instruments:
LM4929MMX/NOPB