DM163024 - Microchip Technology - Datasheet.Directory

PICDEM.net™ 2

Internet/Ethernet

Development Board

User’s Guide

Information contained in this publication regarding device

applications and the like is provided only for your convenience

and may be superseded by updates. It is your responsibility to

ensure that your application meets with your specifications.

MICROCHIP MAKES NO REPRESENTATIONS OR

WARRANTIES OF ANY KIND WHETHER EXPRESS OR

IMPLIED, WRITTEN OR ORAL, STATUTORY OR

OTHERWISE, RELATED TO THE INFORMATION,

INCLUDING BUT NOT LIMITED TO ITS CONDITION,

QUALITY, PERFORMANCE, MERCHANTABILITY OR

FITNESS FOR PURPOSE. Microchip disclaims all liability

arising from this information and its use. Use of Microchip

devices in life support and/or safety applications is entirely at

the buyer’s risk, and the buyer agrees to defend, indemnify and

hold harmless Microchip from any and all damages, claims,

suits, or expenses resulting from such use. No licenses are

conveyed, implicitly or otherwise, under any Microchip

intellectual property rights.

Trademarks

The Microchip name and logo, the Microchip logo, Accuron,

dsPIC, KEELOQ, KEELOQ logo, microID, MPLAB, PIC,

PICmicro, PICSTART, PRO MATE, rfPIC and SmartShunt are

registered trademarks of Microchip Technology Incorporated

in the U.S.A. and other countries.

AmpLab, FilterLab, Linear Active Thermistor, Migratable

Memory, MXDEV, MXLAB, SEEVAL, SmartSensor and The

Embedded Control Solutions Company are registered

trademarks of Microchip Technology Incorporated in the

U.S.A.

Analog-for-the-Digital Age, Application Maestro, CodeGuard,

dsPICDEM, dsPICDEM.net, dsPICworks, ECAN,

ECONOMONITOR, FanSense, FlexROM, fuzzyLAB,

In-Circuit Serial Programming, ICSP, ICEPIC, Mindi, MiWi,

MPASM, MPLAB Certified logo, MPLIB, MPLINK, PICkit,

PICDEM, PICDEM.net, PICLAB, PICtail, PowerCal,

PowerInfo, PowerMate, PowerTool, REAL ICE, rfLAB, Select

Mode, Smart Serial, SmartTel, Total Endurance, UNI/O,

WiperLock and ZENA are trademarks of Microchip

Technology Incorporated in the U.S.A. and other countries.

SQTP is a service mark of Microchip Technology Incorporated

in the U.S.A.

All other trademarks mentioned herein are property of their

respective companies.

Printed on recycled paper.

Note the following details of the code protection feature on Microchip devices:

• Microchip products meet the specification contained in their particular Microchip Data Sheet.

• Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the

intended manner and under normal conditions.

• There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our

knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data

Sheets. Most likely, the person doing so is engaged in theft of intellectual property.

• Microchip is willing to work with the customer who is concerned about the integrity of their code.

• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not

mean that we are guaranteeing the product as “unbreakable.”

Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our

products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts

allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.

Microchip received ISO/TS-16949:2002 certification for its worldwide

headquarters, design and wafer fabrication facilities in Chandler and

Tempe, Arizona; Gresham, Oregon and design centers in California

and India. The Company’s quality system processes and procedures

are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping

devices, Serial EEPROMs, microperipherals, nonvolatile memory and

analog products. In addition, Microchip’s quality system for the design

and manufacture of development systems is ISO 9001:2000 certified.

PICDEM.net™ 2 DEVELOPMENT

BOARD USER’S GUIDE

Table of Contents

Preface ........................................................................................................................... 1

Chapter 1. Introduction to the PICDEM.net 2 Development Board

1.1 Introduction ..................................................................................................... 7

1.2 Highlights ........................................................................................................ 7

1.3 The Development Kit: What’s In The Box ...................................................... 7

1.4 The PICDEM.net 2 Development Board ........................................................ 8

1.5 The Development Kit CD .............................................................................. 10

Chapter 2. Getting Started with the PICDEM.net 2 Development Board

2.1 Highlights ...................................................................................................... 11

2.2 Network Precautions: Before You Start ........................................................ 11

2.3 Using PICDEM.net 2 Development Board with a Local Host System .......... 12

2.4 Connecting the PICDEM.net 2 Development Board .................................... 13

2.5 Configuring the PICDEM.net 2 Development Board .................................... 16

2.6 Establishing Communications ...................................................................... 19

Chapter 3. Using the Microchip TCP/IP Stack Demo Application

3.1 Highlights ...................................................................................................... 21

3.2 Overview ...................................................................................................... 21

3.3 The Source Code ......................................................................................... 21

3.4 Experimenting With Demo Application Firmware ......................................... 22

3.5 Experimenting with the Demo Web Site ....................................................... 23

Chapter 4. Reconfiguring and Restoring the PICDEM.net 2 Development Board

4.1 Highlights ...................................................................................................... 25

4.2 Reconfiguring the PICDEM.net 2 Development Board Hardware ................ 25

4.3 Reconfiguring The PICDEM.net 2 Development Board Firmware ............... 28

4.4 Reprogramming and Restoring the Application Firmware ............................ 31

Chapter 5. Troubleshooting

5.1 Highlights ...................................................................................................... 33

5.2 Common Issues ........................................................................................... 33

Appendix A. PICDEM.net 2 Development Board Schematics, Rev. 4 .................... 37

Index ............................................................................................................................. 43

Worldwide Sales and Service .................................................................................... 46

PICDEM.net™ 2 Development Board User’s Guide

NOTES:

PICDEM.net™ 2 DEVELOPMENT

BOARD USER’S GUIDE

Preface

INTRODUCTION

This chapter contains general information that will be useful to know before using the

Development Board. Items discussed in this chapter include:

• Document Layout

• Conventions Used in this Guide

• Warranty Registration

• Recommended Reading

• The Microchip Web Site

• Development Systems Customer Change Notification Service

• Customer Support

• Document Revision History

DOCUMENT LAYOUT

This document describes how to use the PICDEM.net 2 Development Board as a

development tool to emulate and debug firmware on a target board. The manual layout

is as follows:

•Chapter 1. “Introduction to the PICDEM.net 2 Development Board” – Describes

what the PICDEM.net 2 Development Board is and what features are available on

the board.

•Chapter 2. “Getting Started with the PICDEM.net 2 Development Board” –

Describes how to connect and begin to use the PICDEM.net 2 Development Board.

•Chapter 3. “Using the Microchip TCP/IP Stack Demo Application” – Provides

a brief overview of the TCP/IP Stack Demo Application firmware and source code,

and how to modify the application and the demo web site.

•Chapter 4. “Reconfiguring and Restoring the PICDEM.net 2 Development

Board” – Provides instructions on changing hardware configuration, loading a web

page into the on-board EEPROM and reconfiguring the network settings.

•Chapter 5. “Troubleshooting” – Provides information on solving common problems.

•Appendix A. “PICDEM.net 2 Development Board Schematics, Rev. 4” –

Provides schematic diagrams of the Development Board.

NOTICE TO CUSTOMERS

All documentation becomes dated, and this manual is no exception. Microchip tools and

documentation are constantly evolving to meet customer needs, so some actual dialogs

and/or tool descriptions may differ from those in this document. Please refer to our web site

(www.microchip.com) to obtain the latest documentation available.

Documents are identified with a “DS” number. This number is located on the bottom of each page,

in front of the page number. The numbering convention for the DS number is “DSXXXXXA”, where

“XXXXX” is the document number and “A” is the revision level of the document.

For the most up-to-date information on development tools, see the MPLAB® IDE on-line help.

Select the Help menu, and then Topics to open a list of available on-line help files.

PICDEM.net™ 2 Development Board User’s Guide

CONVENTIONS USED IN THIS GUIDE

This manual uses the following documentation conventions:

DOCUMENTATION CONVENTIONS

Description Represents Examples

Arial font:

Italic characters Referenced books “MPLAB® IDE User’s Guide”

Emphasized text ...is the only compiler...

Initial caps A window the Output window

A dialog the Settings dialog

A menu selection select Enable Programmer

Quotes A field name in a window or

dialog

“Save project before build”

Underlined, italic text with

right angle bracket

A menu path File>Save

Bold characters A dialog button Click OK

A tab Click the Power tab

Text in angle brackets < > A key on the keyboard Press <Enter>, <F1>

Courier New font:

Plain Courier New Sample source code #define START

Filenames autoexec.bat

File paths c:\mcc18\h

Keywords _asm, _endasm, static

Command-line options -Opa+, -Opa-

Bit values 0, 1

Constants 0xFF, ‘A’

Italic Courier New A variable argument file.o, where file can be

any valid filename

Square brackets [ ] Optional arguments mcc18 [options] file

[options]

Curly brackets and pipe

character: { | }

Choice of mutually exclusive

arguments; an OR selection

errorlevel {0|1}

Ellipses... Replaces repeated text var_name [,

var_name...]

Represents code supplied by

user

Preface

WARRANTY REGISTRATION

Please complete the enclosed Warranty Registration Card and mail it promptly.

Sending in the Warranty Registration Card entitles users to receive new product

updates. Interim software releases are available on the Microchip web site.

RECOMMENDED READING

This user’s guide describes how to use the PICDEM.net 2 Development Board. Other

useful documents are listed below. The following Microchip documents are

available and recommended as supplemental reference resources.

Readme for Development Kit

For the latest information on using the PICDEM.net 2 Development Board, read the

Readme for PICDEMnet 2.txt file (an ASCII text file) on the “PICDEM.net™ 2

Development Kit” CD-ROM included with the Development Board kit. The Readme file

contains updated information and known issues that may not be included in this user’s

guide.

Readme Files

For the latest information on using other tools, read the tool-specific Readme files in

the Readmes subdirectory of the MPLAB® IDE installation directory. The Readme files

contain updated information and known issues that may not be included in this user’s

guide.

“PIC18F97J60 Family Data Sheet” (DS39762)

Consult this document for detailed information on Microchip’s first family of 8-bit

microcontrollers with on-chip Ethernet capability. Reference information found in this

data sheet includes:

• Device pinout and packaging details

• Device electrical specifications

• Device memory map

• List of peripherals included on the device

• Practical information on using the Ethernet interface module in connectivity

solutions

“ENC28J60 Data Sheet” (DS39662)

Consult this document for detailed information on the non-microcontroller Ethernet

interface. Reference information found in this data sheet includes:

• Device pinout and packaging details

• Device electrical specifications

• Device memory map

• Practical information on using the Ethernet interface module in connectivity

solutions

AN833, “The Microchip TCP/IP Stack” (DS00833)

This particular application note gives a detailed explanation of the free Microchip

TCP/IP Stack on which the kit’s firmware is based. It is referred to throughout this

manual as a primary reference.

PICDEM.net™ 2 Development Board User’s Guide

THE MICROCHIP WEB SITE

Microchip provides online support via our web site at www.microchip.com. This web

site is used as a means to make files and information easily available to customers.

Accessible by using your favorite Internet browser, the web site contains the following

information:

•Product Support – Data sheets and errata, application notes and sample

programs, design resources, user’s guides and hardware support documents,

latest software releases and archived software

•General Technical Support – Frequently Asked Questions (FAQs), technical

support requests, online discussion groups, Microchip consultant program

member listing

•Business of Microchip – Product selector and ordering guides, latest Microchip

press releases, listing of seminars and events, listing of Microchip sales offices,

distributors and factory representatives

DEVELOPMENT SYSTEMS CUSTOMER CHANGE NOTIFICATION SERVICE

Microchip’s customer notification service helps keep customers current on Microchip

products. Subscribers will receive e-mail notification whenever there are changes,

updates, revisions or errata related to a specified product family or development tool of

interest.

To register, access the Microchip web site at www.microchip.com, click on Customer

Change Notification and follow the registration instructions.

The Development Systems product group categories are:

•Compilers – The latest information on Microchip C compilers and other language

tools. These include the MPLAB® C18 and MPLAB C30 C compilers; MPASM™

and MPLAB ASM30 assemblers; MPLINK™ and MPLAB LINK30 object linkers;

and MPLIB™ and MPLAB LIB30 object librarians.

•Emulators – The latest information on Microchip in-circuit emulators. This

includes the MPLAB ICE 2000 and MPLAB ICE 4000.

•In-Circuit Debuggers – The latest information on the Microchip in-circuit

debugger, MPLAB ICD 2.

•MPLAB® IDE – The latest information on Microchip MPLAB IDE, the Windows®

operating system Integrated Development Environment for development systems

tools. This list is focused on the MPLAB IDE, MPLAB SIM simulator, MPLAB IDE

project manager and general editing and debugging features.

•Programmers – The latest information on Microchip programmers. These include

the MPLAB PM3 and PRO MATE® II device programmers, the PICSTART® Plus

development programmer and the PICkit® 1 starter kit.

Preface

CUSTOMER SUPPORT

Users of Microchip products can receive assistance through several channels:

• Distributor or Representative

• Local Sales Office

• Field Application Engineer (FAE)

• Technical Support

• Development Systems Information Line

Customers should contact their distributor, representative or Field Application Engineer

(FAE) for support. Local sales offices are also available to help customers. A listing of

sales offices and locations is included in the back of this document.

Technical support is available through the web site at: http://support.microchip.com.

DOCUMENT REVISION HISTORY

Revision A (September 2006)

• Initial Release of this Document.

Revision B (June 2007)

• Edits to Section 1.3 “The Development Kit: What’s In The Box”.

PICDEM.net™ 2 Development Board User’s Guide

NOTES:

PICDEM.net™ 2 DEVELOPMENT

BOARD USER’S GUIDE

Chapter 1. Introduction to the PICDEM.net 2

Development Board

1.1 INTRODUCTION

The PICDEM.net 2 Development Board was created to allow developers to examine

Microchip’s latest available technology in embedded Ethernet and Internet solutions.

Using the free Microchip TCP/IP Stack source code, developers can experiment with

the preprogrammed Microchip TCP/IP Demo Application and learn how to integrate

connectivity into their applications.

1.2 HIGHLIGHTS

This chapter covers the following:

• The Development Kit: What’s In The Box

• The PICDEM.net 2 Development Board

• The Development Kit CD

1.3 THE DEVELOPMENT KIT: WHAT’S IN THE BOX

Your Development Kit contains the following items:

1. The PICDEM.net 2 Development Board

2. A standard CAT5 “straight-through” network cable for networking the board

3. A CAT5 “crossover” network cable for networking the board directly to a

computer

4. The “PICDEM.net™ 2 Development Kit” CD-ROM

5. A warranty registration card

PICDEM.net™ 2 Development Board User’s Guide

1.4 THE PICDEM.net 2 DEVELOPMENT BOARD

The PICDEM.net 2 Development Board has all the features to begin developing

Internet connectivity applications over an Ethernet connection. The preprogrammed

firmware allows users to begin evaluating the board right out of the box with no

additional programming or configuration. All that is required to begin exploring the

board is a network-enabled computer with an Ethernet adapter and Internet browser

software. (See Chapter 2. “Getting Started with the PICDEM.net 2 Development

Board” for more specific information.)

FIGURE 1-1: PICDEM.net™ 2 DEVELOPMENT BOARD LAYOUT

Features on the PICDEM.net 2 Development Board include:

1. MICROCONTROLLER: A Microchip PIC18F97J60 microcontroller with built-in

Ethernet controller and transceiver is directly installed on the board (U3). The

device is clocked at 25 MHz and has been preprogrammed with the Demo Appli-

cation firmware using the Microchip TCP/IP Stack. Jumpers, JP15 and JP3, can

be used to measure the current consumption of the microcontroller.

2. ETHERNET CONTROLLER: In addition to the PIC18F97J60, the PICDEM.net 2

Development Board also features a Microchip ENC28J60 stand-alone Ethernet

controller. This device provides Ethernet connectivity for microcontroller-based

applications using a standard SPI interface.

3. MEMORY: A Microchip 25LC256 serial EEPROM (U4) provides 256 Kbits

(32 Kbytes) of storage for both web pages and nonvolatile configuration options.

The 25LC256 is programmable via an SPI interface.

4. LCD DISPLAY: A two-line by 16-character dot matrix display shows diagnostic

and error messages with the factory programmed firmware. It may be used for

other applications with appropriate reprogramming.

PICDEM.net™ 2

Development Board

PICtail™

Daughter

Board

Introduction to the PICDEM.net 2 Development Board

5. OPTIONAL EXTERNAL LCD CONNECTOR: Space is provided on the board for

the installation of a 30-pin, bottom contact FFC edge connector (Hirose

FH12-30S-0.5SH or equivalent). This will allow the use of an external LCD

character display module (such as one of the Optrex™ F-51320 series) to the

board via a ribbon cable. Note that using an external LCD module will require

appropriate changes to the application code, as well as the use of a ribbon cable

compatible with the connector.

6. TEMPERATURE SENSOR: This analog temperature sensor, a Microchip

TC1047 (U1), is connected to an analog I/O pin of the microcontroller. It can be

disconnected by jumper.

7. USER-DEFINED LEDs: Eight LEDs are driven by digital I/O pins of the controller

(PORTJ) and may be used to simulate a digital output to an embedded device.

They may also be enabled or disabled by jumper selection on the board.

8. USER-DEFINED PUSH BUTTONS: These switches are connected to digital I/O

pins on the microcontroller (PORTB<3:0>) and may be used to simulate a digital

input in an embedded application.

9. USER-DEFINED POTENTIOMETER: One 10 kOhm potentiometer is connected

to an analog I/O pin of the microcontroller. It can be used to simulate an analog

input in an embedded application.

10. RESET PUSH BUTTON: This switch is tied to the MCLR pin on the controller,

and is used to reset the board.

11. RJ-45 (10Base-T) MODULAR CONNECTORS: The PICDEM.net 2

Development Board is outfitted with two Integrated Connector Modules (ICMs),

one each for the PIC18F97J60 and ENC28J60. These ICMs provide the modu-

lar jack, as well as the necessary transformers, EMI suppression and status

LEDs, for Ethernet connectivity.

Each ICM has its own ACTIVITY and LINK LEDs on the left and right sides of the

ICM, respectively (as viewed from the top). These show if an Ethernet application

is transmitting or receiving a packet, and if the Ethernet connection is active. The

LEDs for the PIC18F97J60 (on J1) can be disconnected by jumpers if the I/O

ports, RA0 and RA1, are to be used for another purpose.

12. RJ-11 (Six-Wire) MODULAR CONNECTOR: This allows the Development

Board to be connected to Microchip MPLAB ICD 2 systems for in-system

programming, as well as advanced application debugging.

13. SERIAL PORT: The PICDEM.net 2 Development Board includes an RS-232 port

with a DB9 connector (P1) and appropriate level-shifting hardware (U5). This

allows for the configuration of the board’s IP and Ethernet address through a

standard serial connection. This interface also allows users to download new

web pages to the EEPROM.

14. I/O AND PICtail™ DAUGHTER BOARD ACCESS: A pair of female risers (J5

and J6) allow direct access to five of the microcontroller’s I/O ports (PORTA

through PORTE). The even pins of J5 also serve as a standard interface between

the PICDEM.net 2 Development Board and any of Microchip’s PICtail daughter

board series.

15. PROTOTYPE AREA: A 9x20 grid with through-holes is provided for users to

breadboard additional circuitry for development. Three SOT-23 pads and a

SOIC-28 footprint are also provided for surface mounting common components.

Connections are provided for +3.3 VDC, +5 VDC, +9 VDC and ground.

16. ON-BOARD POWER: Two on-board regulators provide separate 5 VDC and

3.3 VDC at 500 mA common current, from the 9 VDC supplied at J7.

17. POWER-ON LED: This LED (D9) shows the board is powered up.

PICDEM.net™ 2 Development Board User’s Guide

18. ETHERNET ID STICKERS (TRACE SIDE): The numbers on the two stickers

are used to form the unique Media Access Control (MAC) addresses used by

the Ethernet transceivers to identify and filter packets. The number is the base

10 version of the last 6 hexadecimal digits of the 12-digit MAC address. For

example, the sticker number, “12345”, represents 003039h in the MAC address.

One of these is assigned to the PIC18F97J60 and the other to the ENC28J60.

These MAC addresses are provided for evaluation purposes; both addresses

can be changed in software.

1.5 THE DEVELOPMENT KIT CD

The “PICDEM.net 2 Development Kit” CD contains:

• The complete source code for the free Microchip TCP/IP Stack Demo Application.

To install the source code and necessary support files on your computer, run the

installer file, MCHPTCPStack 3.75.exe (available when this manual was

written; your kit may have a newer version). If you are restoring the Demo Applica-

tion firmware and/or the demo web site as originally shipped from the factory, use

the appropriate files as described in Section 3.3 “The Source Code”.

• Other example applications for use with PIC18F97J60 and ENC28J60 devices.

• The complete selection of technical documentation for Microchip’s connectivity

solution, located in the Doc folder. Included are the complete data sheets for the

PIC18F97J60 microcontroller and ENC28J60 Ethernet controller. Also of note, in

this folder is the Microchip Application Note AN833, “The Microchip TCP/IP Stack”

(DS00833) which is referred to throughout this manual.

• This manual, in Adobe® Acrobat® format.

The most up-to-date information on demo solutions, as well as the latest version of the

free Microchip TCP/IP Stack, are available on the Internet Solutions page of the Design

Center at the Microchip web site:

http://www.microchip.com/Ethernet

http://www.microchip.com/tcpip

PICDEM.net™ 2 DEVELOPMENT

BOARD USER’S GUIDE

Chapter 2. Getting Started with the PICDEM.net 2

Development Board

2.1 HIGHLIGHTS

This chapter will cover the following topics:

• Network Precautions: Before You Start

• Using PICDEM.net 2 Development Board with a Local Host System

• Connecting the PICDEM.net 2 Development Board

• Configuring the PICDEM.net 2 Development Board

• Establishing Communications

2.2 NETWORK PRECAUTIONS: BEFORE YOU START

The PICDEM.net 2 Development Board provided in your kit is designed to demonstrate

the possibilities of networking with embedded Microchip controllers over Ethernet and

the Internet. As with any experimental system, however, some precautions are in order

before you start.

Whenever new hardware or software is added to a network, it is always advisable to

create a separate test network that is isolated from your LAN. This allows testing the

new system in a controlled environment and minimizes the possibilities of network

interference from the new equipment. The major sources of potential interference

include:

•Addressing – Each device on the network must have a unique address. If

Dynamic Host Configuration Protocol (DHCP) is in use, the PICDEM.net 2

Development Board will automatically acquire a valid IP address. If DHCP is not

used, or a fixed address is required, adding the board to the network without

assigning an address may create network conflicts.

•Traffic Levels – While the on-board Ethernet controller will filter out unwanted

messages, a highly loaded network with many broadcast messages may place a

sizable burden on the Development Board.

•Data Security – Although it is unlikely that the addition of a single device will

compromise the integrity or privacy of sensitive information, it is always a good

idea to perform extensive testing with new equipment before adding it to a

secure network.

•Experimentation – Even as a simple microcontroller-based device, the

Development Board is capable of generating a high volume of network traffic

which may severely disrupt normal network operations.

PICDEM.net™ 2 Development Board User’s Guide

2.3 USING PICDEM.net 2 DEVELOPMENT BOARD WITH A LOCAL HOST

SYSTEM

Although the PICDEM.net 2 Development Board is ready to communicate on a

DHCP-enabled Ethernet network out of the box, you may have reasons not to do this.

Besides those already mentioned, there may be others, such as:

• You don’t have an Ethernet network available to experiment with

• Your network doesn’t use DHCP and the Development Board must be configured

with an IP address before it’s allowed on the network

• Your network administrator forbids you to put the board on the network

For these reasons, the PICDEM.net 2 Development Board can also communicate

directly with a properly configured desktop system, known here as a local host system.

In this configuration, the host system can communicate and configure the board

through its network connection; it can also configure the board through the serial port.

When configured this way, the setup is referred to as a test system.

The Development Board can also communicate to a network and a local host system

separately. In this setup, the board participates on the network through its Ethernet

connection. At the same time, it is connected to the local host system through the serial

port, from which it can be directly configured.

To function as a local host, the system must meet the following basic requirements:

• Any computer system capable of network communication

• CD-ROM drive (for use with the accompanying CD)

• Standard Ethernet card or integrated adapter, capable of supporting 10 Mbps

operation, with RJ45 connector

• One available standard serial port with a matching COM port available through the

operating system

• Any operating system with TCP/IP Stack software

• Any Internet browser software supporting HTTP 1.1 or higher

• Any terminal emulation package, such as HyperTerminal for Microsoft® Windows®

operating system (for optional serial configuration of the PICDEM.net 2

Development Board)

Note: Throughout this chapter, as well as other places in this manual, we will give

configuration examples in terms of Microsoft Windows operating system.

This is, of course, not the only operating system capable of working with

TCP/IP, but it is the one most generally found on desktop computers. Users

of other operating systems should refer to the appropriate documentation

for appropriate instructions, using the instructions provided as a guideline.

Getting Started with the PICDEM.net 2 Development Board

2.4 CONNECTING THE PICDEM.net 2 DEVELOPMENT BOARD

There are two basic network configurations for the PICDEM.net 2 Development Board:

direct connection to a network and connection to a local host system through a cross-

over cable. If DHCP is not enabled on the network, the board will need to be configured

before a direct network connection can be used.

If you are connecting the Development Board to a DHCP-enabled network, follow the

steps in Section 2.4.1 “Connecting to a Network”.

If you are using the board for the first time on a network using fixed IP addresses, follow

the steps in Section 2.4.2 “Connecting Directly to a Host System”. Once the IP

address is configured the first time, you will be able to connect the board directly to the

network as described in Section 2.4.1 “Connecting to a Network” without using a

local host.

If you are connecting the board to a local host in a test system configuration, you will

also follow the steps in Section 2.4.2 “Connecting Directly to a Host System”. If

DHCP is enabled on the local host, the board will configure itself. Otherwise, you will

need to configure both the host and board IP addresses according to the directions in

Section 2.5 “Configuring the PICDEM.net 2 Development Board”.

All of this assumes that the Development Board is running the preprogrammed Demo

Application firmware. The general principles for hardware discussed in the following

sections still apply and may be used as a guideline.

Note: This section assumes that an Ethernet card has already been installed in

the host system and is working properly, and that the TCP/IP protocol has

been installed and bound to the card. If this has not been done, or if you are

uncertain if this has been done, please contact your Information Systems

support person for further assistance.

PICDEM.net™ 2 Development Board User’s Guide

2.4.1 Connecting to a Network

This configuration is the basic method of networking the PICDEM.net 2 Development

Board. This assumes there is a stable Ethernet network using TCP/IP for

communications and that at least one DHCP server is present on the network.

To set up the board for direct networking (see Figure 2-1):

1. Unbox and unwrap the board, and set it on a non-conductive surface near the

host computer.

2. Connect the straight-through Ethernet cable to the board at Ethernet connector

J1, then to the Ethernet network. This can be at a network port or an available

port on a network device (such as a hub, switch or router).

3. Apply power to the board (9 VDC) at J7.

FIGURE 2-1: CONNECTING THE PICDEM.net 2™ DEVELOPMENT BOARD

TO A NETWORK

Note: Do NOT use the provided crossover cable if you are directly connecting the

board to a network or network device. The crossover cable is intended only

for connecting the board directly to a computer.

Note: The Development Kit does not include a power supply. An unregulated

2.5 mm center-positive DC supply of 7V to 12V (preferably 9V) with a

current capability of 500 mA is sufficient. If an external supply is needed,

use Microchip part number AC162039.

9VDC from

Power Supply

PICDEM.net™ 2 Development Board

Network Cable

Ethernet Port

Ethernet Network Device

Network Port

Straight-Through

(J1)

PICDEM.net™ 2

Development

Board

PICtail™

Daughter

Board

Getting Started with the PICDEM.net 2 Development Board

2.4.2 Connecting Directly to a Host System

This option is used under the following situation:

• Evaluation of the Development Board as part of a test system;

• Operation on an isolated network is desired or;

• Connection to a deployed network is not possible.

To set up the board for connection to a local host (see Figure 2-2):

1. Unbox and unwrap the board, and set it on a non-conductive surface near the

host computer.

2. Connect a serial cable to the board, then to the available serial port on your

computer.

3. Depending on the network connection to be used, do one of the following:

For connections through an Ethernet hub or switch: Connect a standard

Ethernet cable to the board, then to a port on the Ethernet device (Option “A” in

Figure 2-2). The computer should already be connected to the hub or switch by

a straight-through cable.

For direct connections to a host system: Connect the Ethernet crossover

cable (supplied in the kit) to the board, then to the computer (Option “B” in

Figure 2-2).

4. Apply power to the board (9 VDC) at J7. (See Section 2.4.1 “Connecting to a

Network” for power supply requirements.)

FIGURE 2-2: CONNECTING TO A HOST SYSTEM THROUGH AN

ETHERNET DEVICE (A) OR A DIRECT CONNECTION (B)

Host Computer

Ethernet

Adapter

Serial Port

(COM1 or

COM2)

9 VDC from

Power Supply

PICDEM.net™ 2 Development Board

Serial Cable

Network Cable

(DB9 to DB9)

Crossover

Ethernet Hub or Switch

Network Cable

Straight-Through

(to board)

Serial Cable

(DB9 to DB9)

(from computer)

Ethernet Port

(J1)

PICDEM.net™ 2

Development

Board

PICDEM.net™ 2 Development Board User’s Guide

2.4.3 Confirming Operation

Once the PICDEM.net 2 Development Board is properly connected and powered up,

you should see all of the following:

• User LED D8 (tied to RJ0) is blinking

• User LEDs D1 through D7 are dark

• The green LINK LED on J1 is lit

• The LCD display shows the message:

TCPStack v3.75

If the network uses DHCP, the display should change after a moment to:

TCPStack v3.75

?.?.?.?

where “?.?.?.?” is the board IP address as assigned by your network server.

If your board does not show all of these things, check all connections with the

power supply and the board. For additional assistance, refer to

Chapter 5. “Troubleshooting”.

If you are using a configuration with a local host system, power the system up now. If

the board and/or local host require IP configuration, proceed to the next section.

Otherwise, skip over to Section 2.6 “Establishing Communications”.

2.5 CONFIGURING THE PICDEM.net 2 DEVELOPMENT BOARD

Once the Development Board is properly connected, it needs to be configured to

operate on the network or with the host system that it is connected to. As already men-

tioned, the board is factory-configured for DHCP operation; it should automatically

acquire an IP address on DHCP-enabled networks and be available for immediate use.

If this describes your configuration, you can proceed to Section 2.6 “Establishing

Communications” and begin experimenting.

If your Development Board is connected to a network without DHCP support, you will

need to assign an IP address to the board. Follow the directions in

Section 2.5.2 “Configuring the PICDEM.net 2 Development Board IP Address”.

If your Development Board is directly connected to a host system, you will need to

determine the IP address of the host system (or assign one, if necessary), and then

configure the board’s IP address accordingly. Start with the directions in

Section 2.5.1 “Obtaining the Host IP Address (Host System Configuration

Only)”, then configure the board as described in Section 2.5.2 “Configuring the

PICDEM.net 2 Development Board IP Address”.

2.5.1 Obtaining the Host IP Address

(Host System Configuration Only)

This process will vary, depending on the operating system used on the host system and

the absence or presence of DHCP configuration on the host system. The procedure

given here is specific to later versions of the Microsoft Windows operating system

(i.e., Windows NT4/2000/XP). If you are unsure if your network uses DHCP to assign

individual machine IP addresses, contact your network support group.

Note: The actual version of the firmware will be reflected in the first line of the LCD

display. Version 3.75 is the revision available at the time this manual was

prepared. Your display may differ.

Getting Started with the PICDEM.net 2 Development Board

Regardless of the operating system, these steps only need to be done once before

using the PICDEM.net 2 Development Board.

1. Open a Command Prompt window. From the Start menu, select

Programs>Accessories>Command Prompt.

2. At the prompt, type the command, ipconfig. This will return the IP

configuration for the host system, including the IP address tied to the Ethernet

card (Figure 2-3).

If the IP address is 0.0.0.0, or the system is configured for DHCP: Continue

with Step 3.

If the IP address is anything except 0.0.0.0: Make a note of the IP address and

continue with the appropriate procedure described in Section 2.5.2 “Configuring

the PICDEM.net 2 Development Board IP Address” (page 18).

3. Type the command, ipconfig/release, and press <ENTER>. You may

receive a message that addresses were automatically configured and cannot be

released; this is normal.

4. Type the command, ipconfig/renew, and press <ENTER>. Wait for about

one minute for the system to return a command prompt. You may receive a

message that the DHCP server was unavailable; this is also normal.

5. Close the window, then open a new Command window.

6. Type the command, ipconfig, and press <ENTER>. The new IP address is

now a non-zero address. Make a note of this.

FIGURE 2-3: THE IPCONFIG SCREEN (WINDOWS® XP)

Note: The example shown in Figure 2-3 is specific to Windows XP. The prompts

and command responses shown differ slightly for other Windows operating

systems, however, the IP address will always be clearly identified as such.

PICDEM.net™ 2 Development Board User’s Guide

2.5.2 Configuring the PICDEM.net 2 Development Board IP Address

By default, the PICDEM.net 2 Development Board uses serial configuration to assign a

permanent IP address to the board. The IP configuration is written to the board’s

EEPROM using a direct serial connection between the board and a host system.

The Microchip TCP/IP Stack can also use a method known as “IP Gleaning” to obtain

an IP address. IP Gleaning is not enabled in the software shipped in the Development

Kit, but it remains available as a compile-time option. Users who may be interested in

using IP Gleaning should refer to Microchip Application Note AN833, “The Microchip

TCP/IP Stack” (DS00833) for detailed information.

To configure the board through the serial port:

1. From the Start menu, select Programs>Accessories>

Communications>HyperTerminal (for some operating systems,

Programs>Accessories>HyperTerminal).

2. At the initial “Connection Description” dialog box, enter a name for the connec-

tion. You may call the terminal session any name that you can easily remember.

Click OK.

3. At the “Connect To” dialog box that follows, choose the appropriate COM port

from the drop-down menu. Click OK.

4. At the “COM Properties” dialog box that follows, select the following settings:

Bits per second: 19200

Data bits: 8

Parity: none

Stop bits: 1

Flow Control: none

Click OK. The Terminal window opens with a flashing cursor. The message,

“Connected”, appears in the status bar at the bottom of the Terminal window,

along with an elapsed time display.

5. From the menu bar, select Files>Properties, then the Settings tab on the

“Properties” dialog. Click on the ASCII Setup button and check the Echo typed

characters locally check box in the following dialog box. Click on OK to exit the

dialog, then OK to exit the “Properties” dialog.

6. Press and hold button RB3 on the board. While holding, press and release the

MCLR button. The terminal responds with the serial configuration menu

(Figure 2-4). At the same time, the LCD displays:

TCPStack v3.75

At this point, release RB3.

Note: These instructions are written specifically for use with the HyperTerminal

emulator package that ships with Windows operating systems. If you are

using another terminal emulation package, the procedure you use to

configure a terminal session may vary slightly. Please consult the

documentation for the terminal software for additional information.

Getting Started with the PICDEM.net 2 Development Board

FIGURE 2-4: THE SERIAL CONFIGURATION MENU

7. Select item 3. At the prompt, enter the board’s new IP address based on the

configuration you are using:

If the board is connected to the local host system through a crossover

cable: Use your host system’s IP address, incremented by one, in the final

position. For example, if the host system’s IP address is “169.225.150.10”, enter

“169.225.150.11”.

If the board is connected to a fixed address network: Use the IP address

assigned by your system administrator.

Press <ENTER>.

8. Select option 8 to disable DHCP and IP Gleaning. This menu will configure the

board to use the manually assigned IP address.

9. Select option 0 to save changes and quit. The LCD should change to:

TCPStack v3.75

?.?.?.?

where “?.?.?.?” is the IP address you just assigned to the board.

10. Close the terminal session. For your convenience, you may save the terminal

session when prompted. You are now ready to communicate with the board.

2.6 ESTABLISHING COMMUNICATIONS

Your PICDEM.net 2 Development Board has already been programmed with the

Demo Application using the Microchip TCP/IP Stack. The on-board external data

EEPROM is also preprogrammed with the demo web site. Once it is hooked up, it is

ready to go – no further software programming is required. At this point, all that

remains is to “log on”.

If you are trying to contact the demo web site across the network, you can do it the

same way you would browse for any site with a hard IP address: enter

http://x.x.x.x in the browser’s address bar, where “x.x.x.x” is the IP address

of the board (check the board’s LCD display for the address).

Note: The actual version of the Demo Application firmware and the current date

will be reflected in the first line of the display. Version 3.75 is the revision

available at the time this manual was prepared. Your display may differ.

PICDEM.net™ 2 Development Board User’s Guide

If the Development Board is connected to a local host system using a crossover cable, it

will be necessary to make some minor changes to your browser’s configuration.

1. Access the browser’s configuration settings in one of two ways:

a) From the Start menu, select Settings>Control Panel, then click on the

Internet Options applet; or

b) Launch the browser, then select Tools>Internet Options from the menu.

2. Select the Connections tab, then click on the LAN Settings button.

3. Verify that the “Use a Proxy Server” box is deselected.

4. Click OK, then OK to close the “Internet Properties” dialog box.

5. Launch the web browser (if not running already).

6. At the address bar, enter http://x.x.x.x, where “x.x.x.x” is the IP

address of the Development Board. Press <Enter>.

7. After a moment, the Microchip TCP/IP Stack page appears:

FIGURE 2-5: MICROCHIP TCP/IP STACK PAGE

You are now ready to experiment with the PICDEM.net 2 Development Board.

Note: These instructions are written specifically for use with Microsoft Internet

Explorer. If you are using Netscape Navigator or another web browser, the

procedure you use will vary. Please consult the documentation for your

browser for additional information.

Note: For users of later versions of Internet Explorer, a message that “No connec-

tion to the Internet is currently available....” may appear. There will be a

choice of two buttons, “Work Offline” or “Try Again”; always choose “Try

Again”. If you choose “Work Offline”, you will not be able to establish an

external connection and will need to close and restart the browser.

PICDEM.net™ 2 DEVELOPMENT

BOARD USER’S GUIDE

Chapter 3. Using the Microchip TCP/IP Stack Demo Application

3.1 HIGHLIGHTS

This chapter will cover the following topics:

•Overview

• The Source Code

• Experimenting With Demo Application Firmware

• Experimenting with the Demo Web Site

3.2 OVERVIEW

The PICDEM.net 2 Development Board’s preprogrammed firmware (referred to

throughout this manual as the “Demo Application”) makes it functional directly out of

the box. Some of the main features are:

• Based on the free Microchip TCP/IP Stack

• Portable across Microchip microcontrollers

• Includes HTTP Server, FTP Server, DHCP Client, IP Gleaning

• User-configurable over RS-232 serial connection

• Web site updatable over RS-232 or Ethernet

This on-board firmware utilizes the free Microchip TCP/IP Stack. In addition to firmware

programmed into the microcontroller, the Demo Application uses the on-board external

serial data EEPROM to store configuration data and demo web site pages.

Your PICDEM.net 2 Development Board is factory-configured with the correct board

serial number and demo web site image. All PICDEM.net 2 Development Boards are

factory programmed to make use of DHCP module. As a result, you can simply connect

the board to a DHCP-enabled network and start evaluating the hardware.

3.3 THE SOURCE CODE

The complete source code for the TCP/IP Stack Demo Application can be installed on

any PC-compatible system by running the installer file, MCHPTCPStack 3.75.exe (or

later version). By default, the Stack uses the ENC28J60 driver (ENC28J60.c), while the

Demo Application uses the Ethernet driver for the PIC18F97J60 family, ETH97J60.c.

Therefore, it is important to verify that ETH97J60.c is included in the application project,

instead of ENC28J60.c. In addition, the precompiler constant, PICDEMNET2, must be

defined. To define this constant, first open a workspace in the \MCHPTCPStack 3.75

directory. Then, in MPLAB IDE, click Project>Build Options...\Project. Select the

MPLAB C18 tab, then under the Macro Definitions box, add “PICDEMNET2”. Make

sure to remove other board definitions, such as “HPC_EXPLORER” or “EXPLORER16”,

if they exist.

The Demo Application can be built and compiled in several different configurations. To

do this, you will need MPLAB IDE to open and compile Demo Application projects. In

addition, you will need a device programmer (such as Microchip PROMATE® 3 device

programmer or MPLAB ICD 2) to program the microcontroller with the application code.

PICDEM.net™ 2 Development Board User’s Guide

There are several MPLAB IDE project files designed to illustrate all of the different

configurations in which the Demo Application can be compiled. These are listed in

Table 3-1. For more information about the Demo Application, refer to Microchip

Application Note AN833, “The Microchip TCP/IP Stack” (DS00833).

TABLE 3-1: WORKSPACE FILES FOR THE DEMO APPLICATION

3.4 EXPERIMENTING WITH DEMO APPLICATION FIRMWARE

You may modify supplied Demo Application code to your requirements. The core of the

Demo Application is implemented by the file, MainDemo.c, which in turn calls the stan-

dard Microchip TCP/IP Stack files. The Stack modules are configured in the header file,

StackTask.h. The selection of appropriate Microchip TCP/IP Stack modules is done

as command-line macro definitions in the compiler settings tab of MPLAB IDE. To

change the Demo Application, it is only necessary to modify MainDemo.c, unless you

also want to modify the individual TCP/IP Stack modules.

A complete discussion of the Microchip TCP/IP Stack and the Demo Application is out

of the scope of this user’s guide. Users who are interested in the details of the

Microchip Stack are encouraged to read Microchip Application Note AN833 “The

Microchip TCP/IP Stack” (DS00833).

3.4.1 Changing the FTP Login Account

The default login values for the Demo Application are “ftp” for the FTP user name and

“microchip” for the password. These text values are stored in the file, MainDemo.c, in

the variables, FTP_USER_NAME and FTP_USER_PASS, respectively. You may modify

one or both of these values as needed. You must rebuild the project and reprogram the

device for the changes to take effect.

3.4.2 Changing the Default IP Configuration

In the versions that do not use the external EEPROM, the Demo Application uses

hard-coded IP configuration values as the default. These may be modified as needed

by changing the values of MY_DEFAULT_??? in the header file, StackTsk.h. You

must rebuild the project and reprogram the device for the changes to take effect.

Project Name Purpose

C18EEPROM.mcw(1) Demo Application using external serial EEPROM as web site

storage – Microchip C18 Compiler

C18ProgramMem.mcw Demo Application using program memory as web site storage –

Microchip C18 Compiler

HTC18EEPROM.mcw Demo Application using external serial EEPROM as web site

storage – HI-TECH PICC-18™ C compiler

HTC18ProgramMem.mcw Demo Application using program memory as web site storage –

HI-TECH PICC-18 C compiler

Note 1: The PICDEM.net 2™ Development Board uses this workspace file.

Using the Microchip TCP/IP Stack Demo Application

3.5 EXPERIMENTING WITH THE DEMO WEB SITE

The PICDEM.net 2 Development Board web site is written in HTML. The complete

source files are available in the \MCHPTCPStack 3.75\WebPages install directory.

You must have working knowledge of HTML in order to correctly modify or create new

web pages. You may design the page by hand (using a text editor) or use a web

authoring tool.

The demo web site is organized as multiple files within a single directory. The Demo

Application includes a special command-line utility program, MPFS.exe. The utility is

written for 32-bit versions of Microsoft Windows operating systems (such as Windows

2000 and Windows XP) to convert a group of files into a Microchip File System (MPFS)

image. Depending on where the MPFS will ultimately be stored, the utility gives you the

option to generate either a data file in C, or a binary file representing the MPFS image.

The complete command line syntax for the utility is:

mpfs [/?] [/c] [/b] [/r<Block>] <InputDir> <OutputFile>

where: /? Displays command-line help

/c Generates a data file in C as output

/b Generates a binary data file as output (default)

/r Reserves a block of memory at the beginning of the file (valid only in

Binary Output mode with a default value of 64 bytes)

<InputDir> The directory containing the files for creating the

MPFS image

<OutputFile> The output file name

For example, the command:

mpfs /c <Your Webpage Dir> mypages.c

generates the MPFS image as a data file, mypages.c, from the content of the directory

“Your Webpage Dir”. In contrast, the command:

mpfs <Your Webpage Dir> mypages.bin

generates a binary file of the image with a 64-byte reserved block, while:

mpfs /r128 <Your Webpage Dir> mypages.bin

generates the same file with a 128-byte reserved block.

If the MPFS image is to be stored in internal program memory, the generated C data

file must be compiled with the application project. If the image is to be stored in an

external serial data EEPROM, the binary file must be downloaded there.

Modifying the content of the static pages, or even adding additional static pages, only

requires minor changes to the demo web site files, but it will be necessary to rebuild

the MPFS image using the MPFS utility and download it into the external EEPROM. If

you want to display additional real-time information, or support additional HTML forms,

you must also modify the HTTP server callback functions in MainDemo.c. For more

information on the callback function, refer to the Microchip Application Note AN833,

“The Microchip TCP/IP Stack” (DS00833).

Note: The current version of the Microchip Stack at the time of this writing utilizes

a 64-byte reserve block. Using a reserve block size other than the default

size of 64 bytes requires a change to the compiler define,

MPFS_RESERVE_BLOCK, in the header file, StackTsk.h. The default

reserve block size may change in future revisions of the Stack.

PICDEM.net™ 2 Development Board User’s Guide

NOTES:

PICDEM.net™ 2 DEVELOPMENT

BOARD USER’S GUIDE

Chapter 4. Reconfiguring and Restoring the

PICDEM.net 2 Development Board

4.1 HIGHLIGHTS

This chapter covers the following:

• Reconfiguring the PICDEM.net 2 Development Board Hardware

• Reconfiguring The PICDEM.net 2 Development Board Firmware

• Reprogramming and Restoring the Application Firmware

4.2 RECONFIGURING THE PICDEM.net 2 DEVELOPMENT BOARD HARDWARE

The PICDEM.net 2 Development Board is provided with a range of hardware features

for manual interaction, as well as a choice of two Ethernet interfaces. In its original

state, the main port (J1) is active and all interactive options are enabled. To allow the

greatest amount of hardware flexibility in developing new applications, users can

change any or all of these configuration options to suit the needs of their application.

4.2.1 Configuring the Hardware Options

The Development Board can be configured to enable or disable its various hardware

features. A total of 23 jumper locations are provided in various places around the board.

As shipped from the factory, all of the locations are bridged by circuit traces, and all of

the features are enabled (with the exception of JP9, discussed below). To change this,

the user will need to cut the traces, and install pins and block jumpers. Afterwards, the

features can be enabled or disabled easily by installing or removing the jumpers.

In some instances, a single function (such as the USART) is connected to the rest of

the board through more than one jumper. This allows selective tailoring of the

controller’s I/O ports to any application that the user may develop. Specific cases are

discussed in the following sections.

The functions of the jumpers are listed in Table 4-1; their locations are shown in

Figure 4-1.

PICDEM.net™ 2 Development Board User’s Guide

TABLE 4-1: JUMPER DESCRIPTIONS

FIGURE 4-1: JUMPER LOCATIONS ON THE DEVELOPMENT BOARD

Number Board

ID(s) Type Description

1 JP1 Bridge U1 (temperature sensor) to RA3

2 JP2 Bridge J2 Power (ENC28J60 Ethernet jack)

3 JP3 Bridge J1 Power (PIC18F97J60 Ethernet jack)

4 JP4 Bridge LED Bank (D1 through D8)

5 JP5 2-way Select ENC28J60 Reset Control (RD2) or Device Disable

6 JP6 Bridge J1 Ethernet Activity LED Enable (LEDA)

7 JP7 Bridge RA0/LEDA to PICtail™ Daughter Board Header

8 JP8 Bridge J1 Ethernet Link LED Enable (LEDB)

9 JP9 Bridge ENC28J60 INT to RB0 (normally open)

10 JP10 Bridge RA1/LEDB to PICtail Daughter Board Header (LEDB)

11 JP11 Bridge ENC28J60 Power

12 JP12 Bridge U4 (EEPROM) SPI Chip Select to RD7

13 JP13 Bridge USART Transmit (microcontroller perspective)

14 JP14 Bridge USART Receive (microcontroller perspective)

15 JP15 Bridge PIC18F97J60 Power

16 JP16 Bridge R38 (potentiometer) to RA2

17 JP17, JP22 Bridge Y3 (Timer1 oscillator)

18 JP18 Bridge S2 (RB0 user-defined push button)

19 JP19 Bridge S3 (RB1 user-defined push button)

20 JP20 Bridge S4 (RB2 user-defined push button)

21 JP21 Bridge S5 (RB3 user-defined push button)

22 JP23 Bridge ENC28J60 SPI Chip Select to RD3

18 19

1 2

3 5

20 21

PICDEM.net™ 2

Development

Board

PICtail™

Daughter

Board

Reconfiguring and Restoring the PICDEM.net 2 Development Board

4.2.1.1 USER-DEFINED CONTROLS AND THE LED BANK

The potentiometer and the user-defined push buttons are each connected to the

PIC18F97J60 through their own individual jumpers. They may be selectively disabled

to allow individual ports to become available for general I/O purposes.

The LED bank (D1 through D8) is enabled as a group with one jumper (JP4).

4.2.1.2 TIMER1 OSCILLATOR (Y3)

By default, ports RC0 and RC1 are configured for use by the Timer1 oscillator. An

appropriate oscillator circuit, including Y3, C45 and C46, is connected across these

pins. Removing jumpers, JP17 and/or JP22, disconnects the circuit and makes one or

both pins available as I/O ports.

4.2.1.3 ETHERNET LED

As shipped, the PICDEM.net 2 Development Board uses pins RA0 and RA1 of the

microcontroller to drive the Ethernet LEDs in J1, generically known as LEDA (the

Activity LED) and LEDB (the Link LED). These signals are also present on RA0 and

RA1 of the PICtail Daughter Board header. Jumpers, JP6, JP7, JP8 and JP10, are used

to connect or disconnect the microcontroller from either the LEDs or the header, or from

both. This is useful in situations when RA0 and RA1 are being used as general I/O pins

and are not needed for network indication.

4.2.1.4 ENC28J60 OPERATION

The Reset state of the ENC28J60 controller is determined by jumper JP5. There are

three possible configurations:

• RD4 (1-2 bridged): The RESET pin is tied to RD4 of the PIC18F97J60. This

allows the microcontroller to execute hardware Resets of the ENC28J60 and use

it as an external Ethernet transceiver.

• Disabled (2-3 bridged): The RESET pin is tied to ground, holding the ENC28J60

in permanent Reset and effectively disabling it.

• Open (no jumper): The RESET pin is disconnected, preventing hardware Resets

but still allowing software device Resets from the SPI bus. This setting also allows

the PIC18F97J60 to use the ENC28J60 as an Ethernet transceiver.

By default, JP5 is configured as “Open” (no jumper).

4.2.2 Using the ENC28J60 as the Ethernet Interface

As shipped, the Development Board uses the Ethernet interface module on the

PIC18F97J60 controller for network connectivity. In this state, J1 is the only active

Ethernet port; J2 is not functional.

It is possible to configure the board to bypass the microcontroller’s on-chip Ethernet

module and use the ENC28J60 interface for connectivity. All of the necessary circuit

connections on the board have already been made. The main factor preventing the

ENC28J60 from being used is that the preprogrammed Microchip TCP/IP Demo

Application has been designed to use the microcontroller’s on-chip Ethernet module.

To use the ENC28J60, it is necessary to program the PIC18F97J60 with a new Demo

Application that uses ENC28J60.c, the required driver for controlling the ENC28J60,

instead of ETH97J60.c. As with other projects using the PIC18F97J60, it is also impor-

tant that the precompiler constant, PICDEMNET2, is defined. Once the PIC18F97J60 is

programmed with the new firmware, J1 will become inactive and J2 will be the

functional Ethernet port.

PICDEM.net™ 2 Development Board User’s Guide

4.3 RECONFIGURING THE PICDEM.net 2 DEVELOPMENT BOARD FIRMWARE

To be ready for use out of the box, the PICDEM.net 2 Development Board is shipped

with preloaded firmware. The firmware has three different components:

• The demo web site page, written in HTML and stored in the external EEPROM.

• The IP configuration, written in binary and also stored in the external EEPROM.

• The PICDEM.net 2 Development Board operating firmware (including the

Microchip TCP/IP Stack and the Demo Application), stored in the program

memory of the microcontroller.

Once in Configuration mode, you can choose to download a new/modified web site or

change network configuration without affecting the operating firmware.

4.3.1 Entering Configuration Mode

In order to change the web site or the network settings, it is necessary to first put the

board into Configuration mode. To do this:

1. Connect the board to the local host system if this is not already done (see

Section 2.4.2 “Connecting Directly to a Host System”, page 15).

2. Connect to the board through the serial port via the terminal emulator

(Section 2.5.2 “Configuring the PICDEM.net 2 Development Board IP Address”,

page 18).

3. Press and hold the user push button (RB3).

4. While holding RB3, press and release the Reset push button.

5. The terminal responds with the Configuration mode menu (Figure 4-2).

6. Release RB3.

FIGURE 4-2: THE SERIAL CONFIGURATION SCREEN

Reconfiguring and Restoring the PICDEM.net 2 Development Board

4.3.2 Changing the Network Configuration

At this point, the PICDEM.net 2 Development Board’s network configuration can be

changed.

To change the Development Board’s serial number:

1. Enter ‘1’.

2. At the “Serial Number (x):” prompt, enter the serial number from the

Ethernet ID sticker on the board or a new Ethernet ID number. The current value

of the serial number will be displayed in the prompt string.

3. Press <ENTER> to submit the changes. Alternatively, simply press <ENTER> to

leave the serial number unchanged.

If the input consists of a non-numerical string, a value of zero will be used.

To change the default IP address:

1. Select item 3.

2. At the “Default IP Address (x.x.x.x):” prompt, enter a new IP address

in dotted decimal notation. The current value of the default IP address will be

displayed in the prompt string. Alternatively, simply press <ENTER> to leave the

IP address unchanged.

If the input does not conform to the standard IP address format, it will be ignored;

no error message will be given.

To change the default gateway address:

1. Select item 4.

2. At the “Default Gateway Address (x.x.x.x):” prompt, enter the new

gateway address in dotted decimal notation. The current value of the default

gateway address will be displayed in the prompt string.

Alternatively, press <ENTER> to leave the IP address unchanged. If the input

does not conform to the standard IP address format, it will be ignored.

To change the default subnet mask:

1. Select item 5.

2. At the “Default Subnet Mask (x.x.x.x):” prompt, enter a new subnet

mask value in dotted decimal notation. The current value of the subnet mask will

be displayed in the prompt string.

Alternatively, press <ENTER> to leave the subnet mask value unchanged. If the

input does not conform to the standard IP address format, it will be ignored.

To change DHCP and IP Gleaning modes:

Enter 7 to enable or enter 8 to disable.

To finish configuration:

Enter 0. The new network configuration is now programmed into the controller’s EEPROM.

NOTES ON IP ADDRESS CONFIGURATION:

• If more than one PICDEM.net 2 Development Board is being evaluated, give each

board a different IP address – even if one is connected at a time. The system may

become confused with different Ethernet IDs being linked to a single IP address.

• Rapid changes in Ethernet IDs and/or IP addresses, especially when more than one

Development Board is being evaluated, may cause a situation where the boards no

longer respond to the test system. This is due to ARP caching by the host system,

where it temporarily retains a stale mapping of MACs and IP addresses.

Note: The factory default address is 169.254.254.254.

PICDEM.net™ 2 Development Board User’s Guide

4.3.3 Loading (or Reloading) the Web Page

Before loading the web page, the HTML file(s) must be translated into the appropriate

binary format using the Microchip File System (MPFS) software utility. The software

utility is included in the \MCHPTCPStack 3.75 install directory.

In general, creating a new web page involves the following:

1. Create or modify existing web pages. You can add as many new files as you

want, provided that the total size does not exceed the external data EEPROMs

capacity of 32 Kbytes. There is no restriction on the size of any of the files, as

long as they fit in the available EEPROM space. You may handwrite your pages

or use professional web authoring tools.

2. Place the files into a single directory.

3. Use the MPFS utility to create an MPFS image of your web site. Refer to

Section 3.5 “Experimenting with the Demo Web Site” for details on using

MPFS.

4. Verify that the size of the finished file is within the capacity of the EEPROM

(32 Kbytes). The MPFS utility will display the actual size of the image.

If you are reloading the original demo web site, the file image is available at

\MCHPTCPStack 3.75\MPFSIMG.bin.

The web site image can be loaded in one of two ways: Serial Configuration mode

(RS-232) from a local host system, or File Transfer Protocol (FTP) over the network.

To Load a Web Site Using Serial Configuration:

1. Connect the board to the host system and enter Configuration mode (page 28).

2. Select item 9 from the Serial Configuration menu to download the MPFS image.

The board returns the prompt “Ready to download MPFS image - Use

Xmodem protocol”.

3. Select Transfer>Send File from the main menu for HyperTerminal (the “Send

File” command for other terminal emulators). Specify the location of the file and

select “XMODEM” for the transfer protocol.

4. After the transfer has finished, the Configuration menu is displayed. Select item 0

to exit Configuration mode.

To Load a Web Site Using FTP:

1. Check that the board is powered up and connected. The order of connections is

not important, as long as the proper network connection for the configuration

(crossover cable to host system, straight cable to network) has been made.

2. Open a Command window.

3. At the command prompt, type the command, ftp x.x.x.x., where “x.x.x.x”

is the IP address of the PICDEM.net 2 Development Board. Press <ENTER>.

4. When prompted, enter the FTP user name and password (the defaults values are

“ftp” and “microchip”, respectively).

5. After successfully logging in, type the command, put xxxxx.bin, where

“xxxxx.bin” is the name of the MPFS binary image file. Press <ENTER>.

6. After notification that the transfer is complete, type “quit” to log off.

A typical exchange between a user and the board is shown in Figure 4-3. FTP client

actions (i.e., manual input from the user) are shown in bold. System prompts and FTP

server responses are shown in plain font face.

Note: Your terminal emulation software must support the standard XMODEM

protocol. Variants, such as XMODEM-1K or any of the CRC variants, will

not work. HyperTerminal supports both XMODEM and XMODEM-1K.

Reconfiguring and Restoring the PICDEM.net 2 Development Board

FIGURE 4-3: EXAMPLE OF AN FTP SESSION WITH THE PICDEM.net 2

DEVELOPMENT BOARD

4.4 REPROGRAMMING AND RESTORING THE APPLICATION FIRMWARE

After investigating the PICDEM.net 2 Development Board and the Demo Application,

you may be ready to modify the application, or perhaps design your own. To do this, it

will be necessary to clear the existing firmware in the Flash program memory of the

PIC18F97J60 microcontroller.

The Development Board does not include the tools for clearing and reprogramming the

microcontroller. You must use an appropriate device programmer or a development

tool, such as the MPLAB IDE, which provides a complete set of tools for programming

and debugging. To ensure proper programming support of the PIC18F97J60, it is

necessary to use MPLAB IDE, version 7.30, at a minimum.

If you have the appropriate development tools (device programmer, development

environment, etc.), you already have everything you need to begin immediately.

To restore the Demo Application, use the hex file, C18EEPROM PICDEMNET2

PIC18F97J60.hex (located in the \MCHPTCPStack 3.75 install directory), to

program the microcontroller. Follow the standard procedure for your device

programmer when programming the microcontroller. Make sure that the following

configuration options are set:

• Oscillator: OSC1/OSC2 as Primary, HS+PLL Oscillator

• Watchdog Timer: Disabled

After programming the controller, reconnect the board to the network or local host

system and verify that the Demo Application is working correctly.

c:\ftp 169.254.254.254

220 ready

User (169.254.254.254: (none)): ftp

331 Password required

Password: microchip

230 Logged in

ftp> put mpfsimg.bin

200 ok

150 Transferring data...

226 Transfer complete

ftp> 16212 bytes transferred in...

ftp> quit

221 Bye

Note 1: The FTP server does NOT echo back the password as the user types it

in. In the instance above, it is shown to illustrate what the user would

enter.

2: See Section 3.4.1 “Changing the FTP Login Account” for instructions

on changing the FTP account login from the default values shown.

3: This example assumes that the MPFS binary image is located in the root

of c:\. If the file is located elsewhere, be sure to include the full path.

PICDEM.net™ 2 Development Board User’s Guide

NOTES:

PICDEM.net™ 2 DEVELOPMENT

BOARD USER’S GUIDE

Chapter 5. Troubleshooting

5.1 HIGHLIGHTS

This chapter will cover the following operational issues and how to resolve them:

• Common Issues

5.2 COMMON ISSUES

1. User LED D8 does not light or flash when power is applied to the board.

Check the PICDEM.net 2 Development Board for power:

• Verify that the power supply is plugged in and the wall outlet has power.

• Check that voltage is available (9 VDC) at the barrel plug.

• Check that the regulated voltages (3.3 VDC and 5 VDC) are available at the

connectors at the prototype area of the board.

Make sure that the microcontroller is programmed correctly. This includes verify-

ing that the device configuration specified by the Flash Configuration Words is

appropriate for the application.

If a programming device is connected via the ICSP™ interface (J4), verify that

the programmer is not holding the device in Reset.

2. The Link LED on the active Ethernet ICM is not lit, or only lights

intermittently.

Check the board for power (see Issue 1, above).

Make sure that the microcontroller is programmed correctly.

Verify that the Ethernet cable is connected to the proper ICM for the firmware

being used.

Verify the connection between the board and the network or local host.

Verify that the correct Ethernet cable is being used:

• When the Development Board is directly connected to the host system, a

crossover cable must be used.

• When the Development Board is connected to the host system through a

network device (such as a hub or switch), a “straight-through” cable must be

used.

3. The LCD doesn’t display a message when power is applied to the

PICDEM.net 2 Development Board.

Check the board for power (see Issue 1, above).

If the board functions normally otherwise (including connectivity to the host

system), the LCD display itself may be faulty. Contact Customer Service for

additional assistance.

Note: If you suspect that one of the Ethernet cables supplied with the kit is

damaged, be certain to replace it with the same type of cable (either

straight-through or crossover). An Ethernet straight-through cable may not

work if the Development Board is directly connected to a host system.

PICDEM.net™ 2 Development Board User’s Guide

4. The PICDEM.net 2 Development Board will not communicate with the host

system.

Verify that the correct Ethernet cable is being used (see Item 2, above).

Verify that the Ethernet cable is connected and undamaged.

Verify that the IP address as displayed on the LCD is used to communicate.

If the board fails when connected through a network device, verify that the device

is working properly. If it is, try connecting the host system directly to the Ethernet

board, as described in Chapter 2. “Getting Started with the PICDEM.net 2

Development Board”. Also, check that the proper cable is being used (see

above).

Check TCP/IP connectivity with the ping command:

1. Launch a DOS (or Command Prompt) window.

2. Type ping x.x.x.x, where “x.x.x.x” is that of the Development Board.

If ping returns the message “Request timed out”, check the Activity LED on the

active Ethernet ICM:

• If the LED blinks during attempted communications, the IP addressing may be

wrong (i.e., the board and the host are not in the same subnet).

• If the LED does NOT blink, the Ethernet cable is defective, or the wrong type,

or the host system has not been properly configured for TCP/IP.

Verify the operation of the Ethernet card. In Microsoft Windows operating

systems, this is done through the System or Network applet in the Control Panel

(the exact applet and method of getting there varies from version to version).

Other operating systems may use different methods. Consult the documentation

for your operating system to get detailed information:

Check the Development Board for power (see Issue 1, above).

If all else fails, reconfigure the Development Board’s network settings using the

default Ethernet ID and IP address. See Section 4.3 “Reconfiguring The

PICDEM.net 2 Development Board Firmware” for more information.

5. The host system communicates with the board, but the demo web site is

not present or does not function correctly.

If the external serial data EEPROM is blank or absent, any attempt to access the

demo web site will result in the message “File Not Found”. If this message

appears, reload the web site to the EEPROM (see Section 4.3.3 “Loading (or

Reloading) the Web Page” for more information).

If the web page display is “broken” (disjointed display, error messages

displayed), use your browser’s “Reload” command to refresh the page. If the

page is still broken, reload the EEPROM (see Section 4.3.3 “Loading (or

Reloading) the Web Page”).

6. The board will not communicate with the host system after changing the IP

address and/or Ethernet ID.

Check the Development Board and host system as in Issue 4, above.

Verify that the host system is set up correctly.

Clear the host system’s ARP cache. For Windows operating systems, open a

Command window, type arp -d * and hit <ENTER>.

If these steps don’t work, restore the Development Board’s default network

configuration to see if communications can be re-established.

See Section 4.3 “Reconfiguring The PICDEM.net 2 Development Board

Firmware” for more information.

Troubleshooting

7. Unable to initiate a serial connection with the PICDEM.net 2 Development

Board.

Carefully review the instructions for the terminal emulation software you are

using. Make certain that the software is correctly installed, and that you are able

to successfully configure a session.

Verify that you are using the correct serial port. Check that the COM port you

have selected in the terminal software is actually the physical port that the serial

cable is connected to.

Verify that the serial cable is properly connected at the host system and the

Development Board, and that the cable is undamaged.

8. Occasionally the demo web site displays “Service Unavailable”.

When the Development Board is updating the web site image via an FTP trans-

fer, all attempted access to the web site will result in the “Service Unavailable”

message. Refresh the page after the FTP transfer is finished.

PICDEM.net™ 2 Development Board User’s Guide

NOTES:

PICDEM.net™ 2 DEVELOPMENT

BOARD USER’S GUIDE

Appendix A. PICDEM.net 2 Development Board

Schematics, Rev. 4

FIGURE A-1: PICDEM.net 2 DEVELOPMENT BOARD SCHEMATIC, SHEET 1 OF 5

(PIC18F97J60 MICROCONTROLLER)

PIC18F97J60

kHz

.1 μF

.1 μF.1 μF.1 μF

.1 μF.1 μF

22 pF 22 pF

2.26K

PICDEM.net™ 2 Development Board User’s Guide

FIGURE A-2: PICDEM.net 2 DEVELOPMENT BOARD SCHEMATIC, SHEET 2 OF 5

(PIC18F97J60 MICROCONTROLLER, ASSOCIATED COMPONENTS)

.1 μF

25 MHz

33 pF

PICDEM.net 2 Development Board Schematics, Rev. 4

FIGURE A-3: PICDEM.net 2 DEVELOPMENT BOARD SCHEMATIC, SHEET 3 OF 5

(ENC28J60 INTERFACE AND ETHERNET MAGNETICS)

ENC28J60

08B0-1X1T-36-F

.1 μF

10 μF

.1 μF

.1 μF.1 μF

25 MHz

33 pF

.1 μF

1000 pF

.1 μF

2 kV

.1 μF

R50 10K

R51 10K

.1 μF

1000 pF 2 kV

08B0-1X1T-36-F

PICDEM.net™ 2 Development Board User’s Guide

FIGURE A-4: PICDEM.net 2 DEVELOPMENT BOARD SCHEMATIC, SHEET 4 OF 5 (RS-232,

EEPROM, TEMPERATURE SENSOR, LCD OPTIONS AND POWER SUPPLY)

MAX3232

TC1047

25LC256

Q1 LM2940S-5.0

Q2 TC1262-3.3VEB

TP4

TP3

TP5

Temperature Sensor

LCD1

LCD2

Alternate LCD Configurations

.1 μF.1 μF

.1 μF

47 μF

.1 μF

47 μF

.1 μF

.1 μF220 μF

.1 μF

PICDEM.net 2 Development Board Schematics, Rev. 4

FIGURE A-5: PICDEM.net 2 DEVELOPMENT BOARD SCHEMATIC, SHEET 5 OF 5 (ICD,

ICSP™, LCD DISPLAY, MICROCONTROLLER HEADER AND PICtail™

DAUGHTER BOARD CONNECTORS)

PICtail™

Daughter

ICD Connector

LCD Character

Display Port

Board

4.7 μF

1 μF

.1 μF

PICDEM.net™ 2 Development Board User’s Guide

NOTES:

PICDEM.net™ 2 DEVELOPMENT

BOARD USER’S GUIDE

Index

AN833, The Microchip TCP/IP Stack....................... 21

ARP Caching ........................................................... 29

Changing the Default IP Configuration .................... 22

Changing the FTP Login Account ............................ 22

Configuring the PICDEM.net 2

Development Board.............................................. 16

Configuring the Host IP Address ...................... 18

Obtaining the Host IP Address ......................... 16

Connecting the PICDEM.net 2

Development Board ................................................. 13

Confirming Operation........................................ 16

Connected to a Network ................................... 14

Connecting Directly to a Host System .............. 15

Customer Notification Service.................................... 4

Customer Support...................................................... 5

Demo Web Site....................................... 20, 28, 34, 35

Experimenting................................................... 23

Development Kit CD ................................................ 10

Development Kit Contents ......................................... 7

Documentation

Conventions........................................................ 2

Layout ................................................................. 1

Dynamic Host Configuration

Protocol (DHCP) ...........................................11, 21, 29

ENC28J60

Operation .......................................................... 27

Use as the Ethernet Interface ........................... 27

Establishing Communications.................................. 19

Ethernet

ID Stickers (Serial Numbers) ............................ 10

Ethernet Controller

ENC28J60 .......................................................... 8

Ethernet Crossover Cable.............................14, 15, 33

Ethernet Integrated Connector Module (ICM)............ 9

File Transfer Protocol (FTP)..................................... 21

FTP

Loading a Web Site .......................................... 30

Service Unavailable Message .......................... 35

HyperText Transfer Protocol (HTTP) ....................... 21

Hypertext Transfer Protocol (HTTP) ........................ 12

Internet Address......................................................... 4

IP Gleaning ...................................................19, 21, 29

LCD

Display ................................................................ 8

Optional External Connector............................... 9

LCD Display ....................................................... 16, 33

LEDs

Power-on............................................................. 9

User-Defined....................................................... 9

Local Host System ................................................... 12

MAC Address ........................................................... 10

Memory

External EEPROM ..................... 18, 21, 23, 30, 34

External EEPROM (25LC256) ............................ 8

MCU Program ............................................. 28, 31

Microchip Internet Web Site ....................................... 4

Microchip TCP/IP Stack ..................................3, 19, 21

Experimenting with Demo

Application Firmware ........................................ 22

Installing the Source Code................................ 21

Microcontroller

PIC18F97J60 ...................................................... 8

Modular Connector..................................................... 9

MPFS Utility ............................................................. 23

Networking Precautions ........................................... 11

On-Board Power ........................................................ 9

PICtail Daughter Board .............................................. 9

Potentiometers

User-Defined....................................................... 9

Prototype Area ........................................................... 9

Push Buttons

Reset............................................................. 9, 28

User-Defined................................................. 9, 28

Recommended Reading ............................................ 3

“ENC28J60 Data Sheet” ..................................... 3

“PIC18F97J60 Family Data Sheet” ..................... 3

AN833, “The Microchip TCP/IP Stack” ............... 3

Readme Files...................................................... 3

PICDEM.net™ 2 Development Board User’s Guide

Reconfiguring PICDEM.net 2 Development Board

Firmware ........................................................... 28

Changing Network Configuration............... 29

Entering Configuration Mode ..................... 28

Loading/Reloading the Web Page ............. 30

Hardware .......................................................... 25

Ethernet LEDs ........................................... 27

Timer1 Oscillator (Y3) ................................ 27

User-Defined Controls and the

LED Bank................................................... 27

Reprogramming and Restoring the Firmware .......... 31

Revision History ......................................................... 5

Schematics

PICDEM.net 2 Development Board ............ 37–41

Serial Configuration

Loading a Web Site........................................... 30

Serial Port .................................................................. 9

Temperature Sensor

TC1047 ............................................................... 9

Troubleshooting

Changing IP Address and/or Ethernet ID..........34

Communications ............................................... 34

Demo Web Site ................................................. 34

LCD Display ...................................................... 33

LED D8.............................................................. 33

Link LED............................................................ 33

Serial Configuration........................................... 35

Services Unavailable......................................... 35

Warranty Registration................................................. 3

WWW Address ........................................................... 4

Index

NOTES:

AMERICAS

Corporate Office

2355 West Chandler Blvd.

Chandler, AZ 85224-6199

Tel: 480-792-7200

Fax: 480-792-7277

Technical Support:

http://support.microchip.com

Web Address:

www.microchip.com

Atlanta

Duluth, GA

Tel: 678-957-9614

Fax: 678-957-1455

Boston

Westborough, MA

Tel: 774-760-0087

Fax: 774-760-0088

Chicago

Itasca, IL

Tel: 630-285-0071

Fax: 630-285-0075

Dallas

Addison, TX

Tel: 972-818-7423

Fax: 972-818-2924

Detroit

Farmington Hills, MI

Tel: 248-538-2250

Fax: 248-538-2260

Kokomo

Kokomo, IN

Tel: 765-864-8360

Fax: 765-864-8387

Los Angeles

Mission Viejo, CA

Tel: 949-462-9523

Fax: 949-462-9608

Santa Clara

Santa Clara, CA

Tel: 408-961-6444

Fax: 408-961-6445

Toronto

Mississauga, Ontario,

Canada

Tel: 905-673-0699

Fax: 905-673-6509

ASIA/PACIFIC

Asia Pacific Office

Suites 3707-14, 37th Floor

Tower 6, The Gateway

Harbour City, Kowloon

Hong Kong

Tel: 852-2401-1200

Fax: 852-2401-3431

Australia - Sydney

Tel: 61-2-9868-6733

Fax: 61-2-9868-6755

China - Beijing

Tel: 86-10-8528-2100

Fax: 86-10-8528-2104

China - Chengdu

Tel: 86-28-8665-5511

Fax: 86-28-8665-7889

China - Fuzhou

Tel: 86-591-8750-3506

Fax: 86-591-8750-3521

China - Hong Kong SAR

Tel: 852-2401-1200

Fax: 852-2401-3431

China - Qingdao

Tel: 86-532-8502-7355

Fax: 86-532-8502-7205

China - Shanghai

Tel: 86-21-5407-5533

Fax: 86-21-5407-5066

China - Shenyang

Tel: 86-24-2334-2829

Fax: 86-24-2334-2393

China - Shenzhen

Tel: 86-755-8203-2660

Fax: 86-755-8203-1760

China - Shunde

Tel: 86-757-2839-5507

Fax: 86-757-2839-5571

China - Wuhan

Tel: 86-27-5980-5300

Fax: 86-27-5980-5118

China - Xian

Tel: 86-29-8833-7252

Fax: 86-29-8833-7256

ASIA/PACIFIC

India - Bangalore

Tel: 91-80-4182-8400

Fax: 91-80-4182-8422

India - New Delhi

Tel: 91-11-4160-8631

Fax: 91-11-4160-8632

India - Pune

Tel: 91-20-2566-1512

Fax: 91-20-2566-1513

Japan - Yokohama

Tel: 81-45-471- 6166

Fax: 81-45-471-6122

Korea - Daegu

Tel: 82-53-744-4301

Fax: 82-53-744-4302

Korea - Seoul

Tel: 82-2-554-7200

Fax: 82-2-558-5932 or

82-2-558-5934

Malaysia - Penang

Tel: 60-4-646-8870

Fax: 60-4-646-5086

Philippines - Manila

Tel: 63-2-634-9065

Fax: 63-2-634-9069

Singapore

Tel: 65-6334-8870

Fax: 65-6334-8850

Taiwan - Hsin Chu

Tel: 886-3-572-9526

Fax: 886-3-572-6459

Taiwan - Kaohsiung

Tel: 886-7-536-4818

Fax: 886-7-536-4803

Taiwan - Taipei

Tel: 886-2-2500-6610

Fax: 886-2-2508-0102

Thailand - Bangkok

Tel: 66-2-694-1351

Fax: 66-2-694-1350

EUROPE

Austria - Wels

Tel: 43-7242-2244-39

Fax: 43-7242-2244-393

Denmark - Copenhagen

Tel: 45-4450-2828

Fax: 45-4485-2829

France - Paris

Tel: 33-1-69-53-63-20

Fax: 33-1-69-30-90-79

Germany - Munich

Tel: 49-89-627-144-0

Fax: 49-89-627-144-44

Italy - Milan

Tel: 39-0331-742611

Fax: 39-0331-466781

Netherlands - Drunen

Tel: 31-416-690399

Fax: 31-416-690340

Spain - Madrid

Tel: 34-91-708-08-90

Fax: 34-91-708-08-91

UK - Wokingham

Tel: 44-118-921-5869

Fax: 44-118-921-5820

WORLDWIDE SALES AND SERVICE

06/25/07

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Microchip:

DM163024