(800) 531-5782 For assistance or to order, call 78HT200 Series 2 AMP POSITIVE STEP-DOWN INTEGRATED SWITCHING REGULATOR * * * * * * High Efficiency > 82% Wide Input Range Self-Contained Inductor Short-Circuit Protection Over-Temperature Protection Fast Transient Response Pin-Out Information The 78HT200 is a series of wide input voltage, 3 terminal Integrated Switching Regulators (ISRs). Employing a ceramic substrate, these ISRs have a maximum output current of 2A. The output voltage is laser trimmed for high accuracy. The 78HT200 series regulators have internal short-circuit and overtemperature protection and may be used in a wide variety of applications. Ordering Information 78HT2 XX Pin No. Function Standard Application Vin 1 78HT200 C1 2 C2 GND Y C 1 Vin 2 GND Output Voltage Package Suffix 3 Vout 33 = 3.3 Volts 46 = 4.6 Volts 05 = 5.0 Volts 53 = 5.25 Volts 65 = 6.5 Volts 75 = 7.5 Volts 10 = 10.0 Volts V = Vertical Mount S = Surface Mount H = Horizontal Mount Vout 3 Revised 9/22/99 + GND C1 = Optional 1F ceramic C2 = Required 100F electrolytic (For dimensions and PC board layout see Package Style 500.) Specifications 78HT200 SERIES Characteristics (Ta = 25C unless noted) Symbols Conditions Min Typ Max Units Output Current Io Over Vin range 0.1* -- 2.0 A Input Voltage Range Vin Io = 0.1 to 2.0A 7 Vo +2V -- -- 15 28 V V Output Voltage Tolerance V o -- 1.0 2.0 %Vo %Vo Vo < 4.6V Vo > 4.6V Over Vin range, Io = 2.0A Ta = 0C to +60C Line Regulation Regline Over Vin range -- 0.4 0.8 Load Regulation Regload 0.1 Io 2.0A -- 0.2 0.4 %Vo Ripple/Noise Vn Vin = Vin min, Io = 2.0A -- 1 -- %Vo Transient Response (with 100F output cap) ttr 50% load change Vo over/undershoot -- 100 5.0 -- Sec %Vo Efficiency Vin = 9V, Io = 2.0A, Vo = 5V -- 82 -- % Switching Frequency o Over Vin and Io ranges Vo > 4.6V Vo = 3.3V 700 0.95 750 1.0 800 1.05 kHz MHz Absolute Maximum Operating Temperature Range Ta -- -40 -- +85 C Recommended Operating Temperature Range Ta Free Air Convection, (40-60LFM) Over Vin and Io ranges -40 -- Thermal Resistance ja Free Air Convection, (40-60LFM) -- 38 -- C/W Storage Temperature Ts -- -40 -- +125 C +85** C Mechanical Shock -- Per Mil-STD-883D, Method 2002.3 -- 500 -- G's Mechanical Vibration -- Per Mil-STD-883D, Method 2007.2, 20-2000 Hz, soldered in a PC board -- 5 -- G's Weight -- -- -- 7 -- Grams * ISR will operate down to no load with reduced specifications. ** See Thermal Derating chart. Note: The 78HT200 Series requires a 100F electrolytic or tantalum output capacitor for proper operation in all applications. Power Trends, Inc. 27715 Diehl Road, Warrenville, IL 60555 (800) 531-5782 Fax: (630) 393-6902 http://www.powertrends.com For assistance or to order, call (800) 531-5782 78HT200 CHARACTERISTIC DATA 78HT233_ 3.3 VDC 78HT205_ 5.0 VDC (See Note 1) (See Note 1) Efficiency vs Output Current Efficiency vs Output Current 100 100 90 Vin 80 8.0V 10.0V 70 12.0V 14.0V 15.0V 60 Efficiency (%) Efficiency (%) 90 Vin 80 8.0V 10.0V 15.0V 70 20.0V 28.0V 60 50 50 40 40 0.0 0.5 1.0 1.5 0.0 2.0 0.5 1.0 Iout (A) 1.5 2.0 Iout (A) Ripple vs Output Current Ripple vs Output Current 60 30 25 50 Vin 20 8.0V 10.0V 12.0V 14.0V 15 15.0V 10 Ripple (mV) Ripple (mV) Series Vin 40 8.0V 10.0V 15.0V 20.0V 28.0V 30 20 10 5 0 0 0.0 0.5 1.0 1.5 0.0 2.0 0.5 1.0 Iout (A) 1.5 2.0 Iout (A) Thermal Derating (Ta) Thermal Derating (Ta) (See Note 2) 70C 2.0 (See Note 2) 2.0 60C 85C 70C 1.5 1.5 Iout (A) Iout (A) 85C 1.0 0.5 1.0 0.5 0.0 0.0 8 10 12 14 16 8 12 16 Vin (Volts) 20 24 28 Vin (Volts) Power Dissipation vs Output Current Power Dissipation vs Output Current 2.5 2.5 2.0 2.0 8.0V 10.0V 12.0V 14.0V 15.0V 1.5 1.0 0.5 Vin PD (Watts) PD (Watts) Vin 8.0V 10.0V 15.0V 20.0V 28.0V 1.5 1.0 0.5 0.0 0.0 0.0 0.5 1.0 Iout (A) 1.5 2.0 0.0 0.5 1.0 1.5 2.0 Iout (A) Note 1: All data listed in the above graphs, except for derating data, has been developed from actual products tested at 25C. This data is considered typical data for the ISR. Note 2: Thermal derating graphs are developed in free air convection cooling of 40-60 LFM. (See Thermal Application Note) Power Trends, Inc. 27715 Diehl Road, Warrenville, IL 60555 (800) 531-5782 Fax: (630) 393-6902 http://www.powertrends.com PACKAGE OPTION ADDENDUM www.ti.com 11-Nov-2009 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty 78HT205HC NRND SIP MOD ULE EFA 3 25 Pb-Free (RoHS) Call TI N / A for Pkg Type 78HT205SC NRND SIP MOD ULE EFC 3 25 Pb-Free (RoHS) Call TI Level-1-215C-UNLIM 78HT205TC NRND SIP MOD ULE EFT 3 25 Pb-Free (RoHS) Call TI N / A for Pkg Type 78HT205VC NRND SIP MOD ULE EFD 3 25 TBD Call TI Level-1-215C-UNLIM 78HT210HC OBSOLETE SIP MOD ULE EFA 3 TBD Call TI Call TI 78HT210SC OBSOLETE SIP MOD ULE EFC 3 TBD Call TI Call TI 78HT210VC OBSOLETE SIP MOD ULE EFD 3 TBD Call TI Call TI Pb-Free (RoHS) Call TI N / A for Pkg Type TBD Call TI Call TI Pb-Free (RoHS) Call TI N / A for Pkg Type MSL Peak Temp (3) 78HT233HC NRND SIP MOD ULE EFA 3 78HT233SC NRND SIP MOD ULE EFC 3 78HT233VC NRND SIP MOD ULE EFD 3 78HT246HC OBSOLETE SIP MOD ULE EFA 3 TBD Call TI Call TI 78HT246SC OBSOLETE SIP MOD ULE EFC 3 TBD Call TI Call TI 78HT246VC OBSOLETE SIP MOD ULE EFD 3 TBD Call TI Call TI 78HT253SC OBSOLETE SIP MOD ULE EFC 3 TBD Call TI Call TI 78HT253VC OBSOLETE SIP MOD ULE EFD 3 TBD Call TI Call TI SIP MOD ULE EFA 3 Pb-Free (RoHS) Call TI N / A for Pkg Type OBSOLETE SIP MOD ULE EFC 3 TBD Call TI Call TI SIP MOD ULE EFT 3 Pb-Free (RoHS) Call TI N / A for Pkg Type 78HT265VC OBSOLETE SIP MOD ULE EFD 3 TBD Call TI Call TI 78HT275HC OBSOLETE SIP MOD ULE EFA 3 TBD Call TI Call TI 78HT275SC OBSOLETE SIP MOD ULE EFC 3 TBD Call TI Call TI 78HT275VC OBSOLETE SIP MOD ULE EFD 3 TBD Call TI Call TI 78HT265HC 78HT265SC 78HT265TC NRND NRND 25 Lead/Ball Finish 25 25 25 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 11-Nov-2009 OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DLP(R) Products DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee(R) Solutions amplifier.ti.com dataconverter.ti.com www.dlp.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2009, Texas Instruments Incorporated