16-Bit, Low Power, Sigma-Delta ADC
Data Sheet
AD7171
Rev. C Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©20092016 Analog Devices, Inc. All rights reserved.
Technical Support www.analog.com
FEATURES
Output data rate: 125 Hz
Pin-programmable power-down and reset
Status function
Internal clock oscillator
Current: 135 µA
Power supply: 2.7 V to 5.25 V
40°C to +105°C temperature range
Package: 10-lead 3 mm × 3 mm LFCSP
INTERFACE
2-wire serial (read-only device)
SPI compatible
Schmitt trigger on SCLK
APPLICATIONS
Weigh scales
Pressure measurement
Industrial process control
Portable instrumentation
FUNCTIONAL BLOCK DIAGRAM
16-BIT Σ-Δ
ADC
AD7171
GND
INTERNAL
CLOCK
VDD REFIN(+)
AIN(+)
AIN(–)
REFIN(–)
DOUT/RDY
SCLK
PDRST
08417-001
Figure 1.
Table 1.
V
REF
= V
DD
RMS Noise
P-P Noise
ENOB
5 V 11.5 µV 76 µV 16 bits 16 bits
3 V
6.9 µV
45 µV
16 bits
GENERAL DESCRIPTION
The AD7171 is a very low power, 16-bit, analog-to-digital
converter (ADC). It contains a precision, 16-bit, Σ-Δ ADC and
an on-chip oscillator. Consuming only 135 µA, the AD7171 is
particularly suitable for portable or battery operated products
where very low power is a requirement. The AD7171 also has a
power-down mode in which the device consumes 5 μA, thus
increasing the battery life of the product.
For ease of use, dedicated pins control all of the features of the
AD7171. Each time a data read occurs, eight status bits are
appended to the 16-bit conversion. These status bits contain a
pattern sequence that can be used to confirm the validity of the
serial transfer.
The output data rate of the AD7171 is 125 Hz, whereas the settling
time is 24 ms. The AD7171 has one differential input and a gain
of 1. This is useful in applications where the user needs to use an
external amplifier to implement system-specific filtering or gain
requirements.
The AD7171 operates with a power supply from 2.7 V to 5.25 V.
It is available in a 10-lead LFCSP.
The AD7170 is a 12-bit version of the AD7171. It has the same
feature set as the AD7171 and is pin-for-pin compatible.
AD7171 Data Sheet
Rev. C | Page 2 of 16
TABLE OF CONTENTS
Features .............................................................................................. 1
Interface ............................................................................................. 1
Applications ....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description ......................................................................... 1
Revision History ............................................................................... 2
Specifications ..................................................................................... 3
Timing Characteristics ................................................................ 5
Timing Diagrams ..................................................................... 5
Absolute Maximum Ratings ............................................................ 6
Thermal Resistance ...................................................................... 6
ESD Caution .................................................................................. 6
Pin Configuration and Function Descriptions ............................. 7
Typical Performance Characteristics ............................................. 8
Output Noise and Resolution Specifications ................................ 9
ADC Circuit Information .............................................................. 10
Overview ..................................................................................... 10
Filter, Data Rate, and Settling Time ......................................... 10
Gain .............................................................................................. 10
Power-Down/Reset (PDRST) ................................................... 10
Analog Input Channel ............................................................... 10
Bipolar Configuration ................................................................ 10
Data Output Coding .................................................................. 11
Reference ..................................................................................... 11
Digital Interface .......................................................................... 11
Grounding and Layout .............................................................. 12
Applications Information .............................................................. 13
Temperature System ................................................................... 13
Signal Conditioning Circuit ...................................................... 13
Outline Dimensions ....................................................................... 14
Ordering Guide .......................................................................... 14
REVISION HISTORY
6/2016—Rev. B to Rev. C
Change to Figure 14 ....................................................................... 13
6/2015—Rev. A to Rev. B
Added Table Number; Renumbered Sequentially ........................ 1
Changed NC Pin (Pin 10) to GND Pin (Pin 10), Figure 5 .......... 7
4/2013—Rev. 0 to Rev. A
Changes to Filter, Data Rate, and Settling Time Section ........... 10
Changes to Temperature System Section .................................... 13
Updated Outline Dimensions ....................................................... 14
Changes to Ordering Guide .......................................................... 14
10/2009—Revision 0: Initial Version
Data Sheet AD7171
Rev. C | Page 3 of 16
SPECIFICATIONS
VDD = 2.7 V to 5.25 V, VREF = VDD, GND = 0 V, all specifications TMIN to TMAX, unless otherwise noted.
Table 2.
Parameter
AD7171B1
Unit Test Conditions/Comments
Min Typ Max
ADC CHANNEL
Output Data Rate (fADC) 125 Hz Settling time = 3/fADC
No Missing Codes2 16 Bits
Resolution Peak-to-Peak (p-p) 16 Bits VINx = 0 V, VREF = VDD
Effective Resolution (ENOB) 16 Bits VINx = 0 V, VREF = VDD
RMS Noise See Table 7 µV VINx = 0 V, VREF = VDD
Integral Nonlinearity ±0.4 LSB
Offset Error ±200 μV
Offset Error Drift vs. Temperature ±250 nV/°C
Full-Scale Error ±0.015 % of FS
Gain Drift vs. Temperature
±0.07
LSB/°C
Power Supply Rejection 85 dB VINx = 1 V
ANALOG INPUTS
Differential Input Voltage Range
±V
REF
V
V
REF
= REFIN(+) REFIN()
Absolute AINx Voltage Limits2 GND − 0.03 VDD + 0.03 V
Average Input Current2 ±400 nA/V Input current varies with input voltage
Average Input Current Drift ±60 pA/V/°C
DC Common-Mode Rejection 90 dB VINx = 1 V
REFERENCE
External REFIN Voltage VDD V REFIN = REFIN(+) − REFIN(−)
Reference Voltage Range2 0.5 VDD V
Absolute REFIN Voltage Limits2
GND − 0.03
V
DD
+ 0.03
V
Average Reference Input Current 400 nA/V
Average Reference Input Current Drift ±0.15 nA/V/°C
DC Common-Mode Rejection 110 dB
INTERNAL CLOCK
Frequency2 64 − 5% 64 + 5% kHz
LOGIC INPUTS
SCLK, PDRST2
Input Low Voltage, VINL 0.4 V VDD = 3 V
0.8 V VDD = 5 V
Input High Voltage, VINH 1.8 V VDD = 3 V
2.4 V VDD = 5 V
SCLK (Schmitt-Triggered Input)2
Hysteresis 100 mV VDD = 3 V
140 mV VDD = 5 V
Input Currents ±2 µA VIN = VDD or GND
Input Capacitance 5 pF All digital inputs
AD7171 Data Sheet
Rev. C | Page 4 of 16
Parameter
AD7171B1
Unit Test Conditions/Comments
Min Typ Max
LOGIC OUTPUT (DOUT/RDY)
Output High Voltage, VOH2 VDD − 0.6 V VDD = 3 V, ISOURCE = 100 µA
4 V VDD = 5 V, ISOURCE = 200 µA
Output Low Voltage, VOL2 0.4 V VDD = 3 V, ISINK = 100 µA
0.4 V VDD = 5 V, ISINK = 1.6 mA
Floating-State Leakage Current ±2 µA
Floating-State Output Capacitance 5 pF
Data Output Coding Offset binary
POWER REQUIREMENTS3
Power Supply Voltage
VDDGND 2.7 5.25 V
Power Supply Currents
IDD Current 110 130 µA VDD = 3 V
135 150 µA VDD = 5 V
IDD (Power-Down/Reset Mode) 5 µA
1 Temperature range is −40°C to +105°C.
2 Specification is not production tested but is supported by characterization data at initial product release.
3 Digital inputs equal to VDD or GND.
Data Sheet AD7171
Rev. C | Page 5 of 16
TIMING CHARACTERISTICS
VDD = 2.7 V to 5.25 V, GND = 0 V, Input Logic 0 = 0 V, Input Logic 1 = VDD, unless otherwise noted.
Table 3.
Parameter1, 2 Limit at TMIN, TMAX Unit Test Conditions/Comments
READ
t1 100 ns min SCLK high pulse width
t2 100 ns min SCLK low pulse width
t33 0 ns min SCLK active edge to data valid delay4
60 ns max VDD = 4.75 V to 5.25 V
80
ns max
V
DD
= 2.7 V to 3.6 V
t4 10 ns min SCLK inactive edge to DOUT/RDY high
RESET
t
5
100
ns min
PDRST low pulse width
t6 25 ms typ PDRST high to data valid delay
1 Sample tested during initial release to ensure compliance. All input signals are specified with tR = tF = 5 ns (10% to 90% of VDD) and timed from a voltage level of 1.6 V.
2 See Figure 3.
3 These numbers are measured with the load circuit shown in Figure 2 and defined as the time required for the output to cross the VOL or VOH limits.
4 SCLK active edge is the falling edge of SCLK.
Timing Diagrams
ISINK ( 1.6mA W IT H VDD = 5V,
100µA W IT H V DD = 3V )
ISOURCE (200µ A WI TH VDD = 5V,
100µA W IT H V DD = 3V )
1.6V
TO
OUTPUT
PIN 50pF
08417-002
Figure 2. Load Circuit for Timing Characterization
t
3
t
1
t
2
t
4
DOUT /RDY ( O)
SCLK (I)
I = INPUT, O = OUTPUT
MSB LSB
08417-003
Figure 3. Read Cycle Timing Diagram
t
5
t
6
PDRST (I)
DOUT /RDY ( O)
I = INPUT, O = OUTPUT
08417-004
Figure 4. Resetting the AD7171
AD7171 Data Sheet
Rev. C | Page 6 of 16
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 4.
Parameter Rating
VDD to GND −0.3 V to +7 V
Analog Input Voltage to GND −0.3 V to VDD + 0.3 V
Reference Input Voltage to GND −0.3 V to VDD + 0.3 V
Digital Input Voltage to GND −0.3 V to VDD + 0.3 V
Digital Output Voltage to GND −0.3 V to VDD + 0.3 V
VINx/Digital Input Current 10 mA
Operating Temperature Range −40°C to +105°C
Storage Temperature Range −65°C to +150°C
Maximum Junction Temperature 150°C
Lead Temperature, Soldering
Reflow 260°C
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
THERMAL RESISTANCE
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Table 5.
Package Type θJA θJC Unit
10-Lead LFCSP 48.7 2.96 °C/W
ESD CAUTION
Data Sheet AD7171
Rev. C | Page 7 of 16
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
08417-005
NOTES
1. CO NNE CT EX P OSE D P AD TO GRO UND.
SCLK
AIN(+)
AIN(–)
REFIN(+)
GND
V
DD
GND
REFIN(–)
PDRST
DOUT/RDY
1
2
3
4
5
10
9
8
7
6
AD7171
TOP VIEW
(Not to S cale)
Figure 5. Pin Configuration
Table 6. Pin Function Descriptions
Pin No. Mnemonic Description
1 SCLK Serial Clock Input. This serial clock input is for data transfers from the ADC. The SCLK has a Schmitt-triggered
input. The serial clock can be continuous with all data transmitted in a constant train of pulses. Alternatively, it
can be a noncontinuous clock with the information being transmitted from the ADC in smaller batches of data.
2 DOUT/RDY Serial Data Output/Data Ready Output. DOUT/RDY serves a dual purpose. DOUT/RDY operates as a data ready
pin, going low to indicate the completion of a conversion. In addition, it functions as a serial data output pin to
access the data register of the ADC. Eight status bits accompany each data read. See Figure 13 for further details.
The DOUT/RDY falling edge can be used as an interrupt to a processor, indicating that new data is available. If
the data is not read after the conversion, the pin goes high before the next update occurs.
3 AIN(+) Analog Input. AIN(+) is the positive terminal of the differential analog input pair AIN(+)/AIN(−).
4 AIN(−) Analog Input. AIN(−) is the negative terminal of the differential analog input pair AIN(+)/AIN(−).
5 REFIN(+) Positive Reference Input. An external reference can be applied between REFIN(+) and REFIN(). The nominal
reference voltage (REFIN(+) REFIN()) is 5 V, but the device can function with a reference of 0.5 V to VDD.
6
REFIN()
Negative Reference Input.
7, 10 GND Ground Reference Point.
8 VDD Supply Voltage, 2.7 V to 5.25 V.
9 PDRST Power-Down/Reset. When this pin is low, the ADC is placed in power-down mode. All the logic on the chip is
reset and the DOUT/RDY pin is tristated. When PDRST is high, the ADC is taken out of power-down mode. The
on-chip clock powers up and settles, and the ADC continuously converts. The internal clock requires 1 ms
approximately to power up.
EPAD Exposed Pad. Connect exposed pad to ground.
AD7171 Data Sheet
Rev. C | Page 8 of 16
TYPICAL PERFORMANCE CHARACTERISTICS
10
8
6
4
2
0
–40 –10 20 50 80 110
RMS NOISE (µV)
TEMPERATURE (°C)
V
REF
= V
DD
= 3V
V
REF
= V
DD
= 5V
08417-015
Figure 6. AD7171 RMS Noise vs. Temperature
0.266
–0.200
–0.133
–0.066
0
0.066
0.133
0.200
–3 32
10–1–2
INL (LSB)
V
IN
(V)
08417-006
Figure 7. Integral Nonlinearity (VREF = VDD)
180
120
140
160
–40 –10 20 50 80 110
OFFSET V)
TEMPERATURE (°C)
08417-007
Figure 8. Offset vs. Temperature
0.025
0.015
0.017
0.021
0.019
0.023
–40 –10 20 50 80 110
GAI N E RROR (%)
TEMPERATURE (°C)
08417-008
Figure 9. Gain Error vs. Temperature
140
132
124
116
108
100
–40 –10 20 50 80 110
IDD ( µA)
TEMPERATURE (°C)
VREF = VDD = 3V
VREF = VDD = 5V
08417-016
Figure 10. Power Supply Current vs. Temperature
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
–40 –10 20 50 80 110
IDD ( µA)
TEMPERATURE (°C)
VREF = VDD = 3V
VREF = VDD = 5V
08417-017
Figure 11. Power-Down Current vs. Temperature
Data Sheet AD7171
Rev. C | Page 9 of 16
OUTPUT NOISE AND RESOLUTION SPECIFICATIONS
Table 7 shows the rms noise of the AD7171. The numbers
given are for a 5 V and a 3 V reference. These numbers are
typical and are generated with a differential input v o l t a g e o f 0 V.
The corresponding p-p resolution is also listed along with the
effective resolution (ENOB). Note that the effective resolution is
calculated using the rms noise, whereas the p-p resolution is based
on the p-p noise. The p-p resolution represents the resolution
for which there is no code flicker. These numbers are typical.
The effective number of bits (ENOB) is defined as
ENOB = ln(FSR/RMS noise)/ln(2)
The noise-free bits, or p-p resolution, are defined as
Noise-Free Bits = ln(FSR/Peak-to-Peak Noise)/ln(2)
where FSR is the full-scale range and is equal to 2 × VREF/gain.
Table 7. RMS Noise and Resolution of the AD7171
VREF = VDD RMS Noise P-P Noise P-P Resolution ENOB
5 V 11.5 μV 76 μV 16 bits 16 bits
3 V 6.9 μV 45 μV 16 bits 16 bits
AD7171 Data Sheet
Rev. C | Page 10 of 16
ADC CIRCUIT INFORMATION
OVERVIEW
The AD7171 is a low power ADC that incorporates a precision
16-bit Σ-∆ modulator and an on-chip digital filter intended for
measuring wide dynamic range, low frequency signals. The device
has an internal clock and one differential input. It operates with
an output data rate of 125 Hz and has a gain of 1. A 2-wire interface
simplifies data retrieval from the AD7171.
FILTER, DATA RATE, AND SETTLING TIME
The AD7171 uses a sinc3 filter. The output data rate is set to 125 Hz;
thus, valid conversions are available every 1/125 = 8 ms. If a reset
occurs, then the user must allow the complete settling time for
the first conversion after the reset. The settling time is equal to
24 ms. Subsequent conversions are available at 125 Hz.
When a step change occurs on the analog input, the AD7171
requires several conversion cycles to generate a valid conversion.
If the step change occurs synchronous to the conversion period,
then the settling time of the AD7171 must be allowed to generate
a valid conversion. If the step change occurs asynchronous to the
end of a conversion, then an extra conversion must be allowed to
generate a valid conversion. The data register is updated with all
the conversions but, for an accurate result, the user must allow
the required time.
Figure 12 shows the filter response of the filter. The only external
filtering required on the analog inputs is a simple RC filter to
provide rejection at multiples of the master clock. See Table 8
for suitable external RC combinations.
0
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0750625500375250125
FILTER GAIN (dB)
INPUT SIG NAL F RE QUENCY ( Hz )
08417-011
Figure 12. Filter Response
GAIN
The AD7171 has a gain of 1. The acceptable analog input range
is ±VREF. Therefore, with VREF = 5 V, the input range is ±5 V.
POWER-DOWN/RESET (PDRST)
The PDRST pin functions as a power-down pin and a reset pin.
When PDRST is taken low, the AD7171 is powered down. The
entire ADC is powered down (including the on-chip clock), and
the DOUT/RDY pin is tristated. The circuitry and serial interface
are also reset. This resets the logic, the digital filter, and the analog
modulator. PDRST must be held low for 100 ns minimum to
initiate the reset function (see Figure 4).
When PDRST is taken high, the AD7171 is taken out of power-
down mode. When the on-chip clock has powered up (1 ms,
typically), the modulator then begins sampling the analog input.
The DOUT/RDY pin becomes active, going high until a valid
conversion is available. A reset is automatically performed on
power-up.
ANALOG INPUT CHANNEL
The AD7171 has one differential analog input channel that is
connected to the modulator; that is, the input is unbuffered.
Note that this unbuffered input path provides a dynamic load to
the driving source. Therefore, resistor/capacitor combinations on
the input pins can cause dc gain errors, depending on the output
impedance of the source that is driving the ADC input. Table 8
shows the allowable external resistance/capacitance values such
that no gain error at the 16-bit level is introduced.
Table 8. External RC Combination for No Gain Error
C (pF)
R (Ω)
50 9000
100 6000
500 1500
1000 900
5000 200
The absolute input voltage range is restricted to a range between
GND 30 mV and VDD + 30 mV. Care must be taken in setting
up the common-mode voltage to avoid exceeding these limits.
Otherwise, there is degradation in linearity and noise performance.
BIPOLAR CONFIGURATION
The AD7171 accepts a bipolar input range. A bipolar input range
does not imply that the device can tolerate negative voltages with
respect to system GND. Signals on the AIN(+) input are referenced
to the voltage on the AIN() input. For example, if AIN(−) is 2.5 V,
the analog input range on the AIN(+) input is 0 V to 5 V when a
2.5 V reference is used.
Data Sheet AD7171
Rev. C | Page 11 of 16
DATA OUTPUT CODING
The AD7171 uses offset binary coding. Therefore, a negative
full-scale voltage results in a code of 000...000, a zero differential
input voltage results in a code of 100...000, and a positive full-
scale input voltage results in a code of 111...111. The output
code for any analog input voltage can be represented as
Code = 2N – 1 × ((VINx/VREF) + 1)
where:
VINx is the analog input voltage.
N = 16 for the AD7171.
REFERENCE
The AD7171 has a fully differential input capability for the channel.
The common-mode range for these differential inputs is GND to
VDD. The reference input is unbuffered; therefore, excessive RC
source impedances introduce gain errors. The reference voltage
REFIN (REFIN(+) REFIN()) is VDD nominal, but the AD7171
is functional with reference voltages of 0.5 V to VDD. In applications
where the excitation (voltage or current) for the transducer on
the analog input also drives the reference voltage for the device,
the effect of the low frequency noise in the excitation source is
removed because the application is ratiometric. If the AD7171 is
used in a nonratiometric application, a low noise reference
should be used.
Recommended 2.5 V reference voltage sources for the AD7171
include the ADR381 and ADR391, which are low noise, low
power references. Also, note that the reference inputs provide a
high impedance, dynamic load. Because the input impedance of
each reference input is dynamic, resistor/capacitor combinations
on these inputs can cause dc gain errors, depending on the output
impedance of the source that is driving the reference inputs.
Reference voltage sources such as those recommended above
(the ADR391, for example) typically have low output impedances
and are, therefore, tolerant to decoupling capacitors on REFIN(+)
without introducing gain errors in the system. Deriving the
reference input voltage across an external resistor means that
the reference input sees a significant external source impedance.
External decoupling on the REFIN(±) pins is not recommended
in this type of circuit configuration.
DIGITAL INTERFACE
The serial interface of the AD7171 consists of two signals: SCLK
and DOUT/RDY SCLK is the serial clock input for the device,
and data transfers occur with respect to the SCLK signal. The
DOUT/RDY pin is dual purpose: it functions as a data ready
pin and as a data out pin. DOUT/RDY goes low when a new
data-word is available in the output register. A 24-bit word is
placed on the DOUT/RDY pin when sufficient SCLK pulses are
applied. This consists of a 16-bit conversion result followed by
eight status bits. Table 9 shows the functions of the status bits.
RDY: Ready bit. This bit is set low to indicate that a conversion
is available.
0: This bit is set to 0.
ERR: This bit is set to 1 if an error occurred during the conversion.
An error occurs when the analog input is outside range.
ID1, ID0: ID bits. These bits indicate the ID number for the
AD7171. Bit ID1 is set to 0 and Bit ID0 is set to 1 for the AD7171.
PAT2, PAT1, PAT0: Status pattern bits. These bits are set to 101
by default. When the user reads the data from the AD7171, a
pattern check can be performed. If the PAT2 to PAT0 bits are
different from their default values, the serial transfer from the
ADC was not performed correctly.
Table 9. Status Bits
RDY 0 ERR ID1 ID0 PAT2 PAT1 PAT0
DOUT/RDY is reset high when the conversion is read. If the
conversion is not read, DOUT/RDY goes high prior to the data
register update to indicate when not to read from the device. This
ensures that a read operation is not attempted while the register
is being updated. Each conversion can be read only once. The
data register is updated for every conversion. Therefore, when a
conversion is complete, the serial interface resets, and the new
conversion is placed in the data register. Therefore, the user
must ensure that the complete word is read before the next
conversion is complete.
When PDRST is low, the DOUT/RDY pin is tristated. When
PDRST is taken high, the internal clock requires 1 ms, approx-
imately, to power up. Following this, the ADC continuously
converts. The first conversion requires the complete settling
time (see Figure 4). DOUT/RDY goes high when PDRST is
taken high and returns low only when a conversion is available.
The ADC then converts continuously, subsequent conversions
being available at 125 Hz. Figure 3 shows the timing for a read
operation from the AD7171.
AD7171 Data Sheet
Rev. C | Page 12 of 16
GROUNDING AND LAYOUT
Because the analog input and reference input of the ADC are
differential, most of the voltages in the analog modulator are
common-mode voltages. The excellent common-mode reject-
ion of the device removes common-mode noise on these inputs.
The digital filter provides rejection of broadband noise on the
power supply, except at integer multiples of the modulator
sampling frequency. The digital filter also removes noise from
the analog and reference inputs provided that these noise sources
do not saturate the analog modulator. As a result, the AD7171 is
more immune to noise interference than conventional high
resolution converters. However, because the noise levels from
the AD7171 are so low, care must be taken with regard to
grounding and layout.
The printed circuit board that houses the AD7171 should be
designed such that the analog and digital sections are separated
and confined to certain areas of the board. A minimum etch
technique is generally best for ground planes because it gives
the best shielding.
It is recommended that the GND pin of the AD7171 be tied to
the analog ground (AGND) plane of the system. In any layout,
it is important that the user pay attention to the flow of currents
in the system, and ensure that the return paths for all currents
are as close as possible to the paths the currents took to reach
their destinations. Avoid forcing digital currents to flow through
the AGND sections of the layout.
The ground plane of the AD7171 should be allowed to run under
the AD7171 to prevent noise coupling. The power supply lines
to the AD7171 should use as wide a trace as possible to provide
low impedance paths and reduce the effects of glitches on the
power supply line. Fast switching signals such as clocks should
be shielded with digital ground to avoid radiating noise to other
sections of the board, and clock signals should never be run near
the analog inputs. Avoid crossover of digital and analog signals.
Traces on opposite sides of the board should run at right angles
to each other. This reduces the effects of feedthrough through the
board. A microstrip technique is by far the best, but it is not
always possible with a double-sided board. In this technique,
the component side of the board is dedicated to ground planes,
while signals are placed on the solder side.
Good decoupling is important when using high resolution ADCs.
VDD should be decoupled with 10 µF tantalum capacitors in parallel
with 0.1 µF capacitors to GND, with the analog ground to digital
ground (DGND) connection of the system being close to the
AD7171. To achieve the best results from these decoupling
components, they should be placed as close as possible to
the device, ideally right up against the device. All logic chips
should be decoupled with 0.1 µF ceramic capacitors to DGND.
Data Sheet AD7171
Rev. C | Page 13 of 16
APPLICATIONS INFORMATION
The AD7171 provides a low cost, high resolution analog-to-digital
function. Because the analog-to-digital function is provided
by a Σ-Δ architecture, the device is more immune to noisy
environments, making it ideal for use in sensor measurement
and industrial and process-control applications.
TEMPERATURE SYSTEM
Figure 13 shows the AD7171 used in a temperature measurement
system. The thermistor is connected in series with a precision
resistor, RREF, the precision resistor being used to generate the
reference voltage. The value of RREF is equal to the maximum
resistance produced by the thermistor. The complete dynamic
range of the ADC is then used, resulting in optimum performance.
See Table 8 for suitable external RC combinations.
16-BIT Σ-Δ
ADC
AD7171
GND
VDD
INTERNAL
CLOCK
VDD
RREF
REFIN(+)
AIN(+)
AIN(–)
REFIN(–)
SCLK
DOUT/RDY
PDRST
08417-013
Figure 13. Temperature System Using the AD7171
SIGNAL CONDITIONING CIRCUIT
Figure 14 shows the AD7171 used in a signal conditioning
circuit for a single-ended analog input. In a low side shunt
current monitor, a low resistance shunt resistor converts the
current to voltage. The resulting voltage is amplified and
applied to the AD7171.
08417-018
AD7171
REFIN(+)
AIN(+)
AIN(–)
REFIN(–)
GND VDD
INTERNAL
CLOCK
SCLK
DOUT/RDY
ADR5041
AD8628
1µF
ANALOG
INPUT
1k
32k
16-BIT
Σ-Δ ADC
Figure 14. Signal Conditioning Circuit
AD7171 Data Sheet
Rev. C | Page 14 of 16
OUTLINE DIMENSIONS
2.48
2.38
2.23
0.50
0.40
0.30
10
1
6
5
0.30
0.25
0.20
PIN 1 INDEX
AREA
SEATING
PLANE
0.80
0.75
0.70
1.74
1.64
1.49
0.20 REF
0.05 M AX
0.02 NO M
0.50 BSC
EXPOSED
PAD
3.10
3.00 SQ
2.90
PIN 1
INDICATOR
(R 0. 15)
FOR PRO P E R CONNECTI ON O F
THE EXPOSED PAD, REFER TO
THE PIN CO NFI GURAT IO N AND
FUNCTI O N DE S CRIPTI ONS
SECTION OF THIS DATA SHEET.
COPLANARITY
0.08
02-05-2013-C
TOP VIEW BOTTOM VIEW
0.20 M IN
Figure 15. 10-Lead Lead Frame Chip Scale Package [LFCSP_WD]
3 mm × 3 mm Body, Very Very Thin, Dual Lead
(CP-10-9)
Dimensions shown in millimeters
ORDERING GUIDE
Model1 Temperature Range Package Description Package Option Branding
AD7171BCPZ-REEL7
40°C to +105°C
10-Lead Lead Frame Chip Scale Package [LFCSP_WD]
CP-10-9
C6G
AD7171BCPZ-500RL7 40°C to +105°C 10-Lead Lead Frame Chip Scale Package [LFCSP_WD] CP-10-9 C6G
EVAL-AD7171EBZ Evaluation Board
1 Z = RoHS Compliant Part.
Data Sheet AD7171
Rev. C | Page 15 of 16
NOTES
AD7171 Data Sheet
Rev. C | Page 16 of 16
NOTES
©20092016 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D08417-0-6/16(C)