SIOV metal oxide varistors
Leaded varistors, AdvanceD series
Series/Type: B722*
Date: January 2018
© EPCOS AG 2018. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
EPCOS AG is a TDK Group Company.
Construction
Round varistor element, leaded
Coating: epoxy resin, flame-retardant to UL 94 V-0
Terminals: tinned wire
Features
High-energy AdvanceD series E2
High surge current ratings up to 10 kA
High energy ratings up to 440 J
Wide operating voltage range 130 … 680 VRMS
PSpice models
Approvals
UL
CSA
VDE
CQC S05/07 (K11 … K460), S10/S14 (K11 … K680), S20 (K11 … K1000)
IEC
Delivery mode
Bulk (standard), taped versions on reel or in Ammo pack upon request.
For further details refer to chapter "Taping, packaging and lead configuration" for leaded
varistors.
General technical data
Climatic category to IEC 60068-1 40/105/56
Operating temperature to IEC 61051 40 ... +105 °C
Storage temperature 40 ... +125 °C
Electric strength to IEC 61051 ≥2.5 kVRMS
Insulation resistance to IEC 61051 ≥100 MΩ
Leaded varistors B722*
AdvanceD series
Page 2 of 35Please read Cautions and warnings and
Important notes at the end of this document.
Electrical specifications and ordering codes
Maximum ratings (TA= 105 °C)
Ordering code Type
(untaped)
SIOV-
VRMS
V
VDC
V
imax
(8/20 µs)
1 time
A
In1)
(8/20 µs)
15 times
A
Wmax
(2 ms)
J
Pmax
W
VRMS = 130 V
B72205S2131K101 S05K130E2 130 170 800 150 6.0 0.10
B72207S2131K101 S07K130E2 130 170 1750 500 12.5 0.25
B72210S2131K101 S10K130E2 130 170 3500 1500 25.0 0.40
B72214S2131K101 S14K130E2 130 170 6000 3000 50.0 0.60
B72220S2131K101 S20K130E2 130 170 10000 3000 100.0 1.00
VRMS = 140 V
B72205S2141K101 S05K140E2 140 180 800 150 6.5 0.10
B72207S2141K101 S07K140E2 140 180 1750 500 13.5 0.25
B72210S2141K101 S10K140E2 140 180 3500 1500 27.5 0.40
B72214S2141K101 S14K140E2 140 180 6000 3000 55.0 0.60
B72220S2141K101 S20K140E2 140 180 10000 3000 110.0 1.00
VRMS = 150 V
B72205S2151K101 S05K150E2 150 200 800 150 7.5 0.10
B72207S2151K101 S07K150E2 150 200 1750 500 15.0 0.25
B72210S2151K101 S10K150E2 150 200 3500 1500 30.0 0.40
B72214S2151K101 S14K150E2 150 200 6000 3000 60.0 0.60
B72220S2151K101 S20K150E2 150 200 10000 3000 120.0 1.00
VRMS = 175 V
B72205S2171K101 S05K175E2 175 225 800 150 8.0 0.10
B72207S2171K101 S07K175E2 175 225 1750 500 17.0 0.25
B72210S2171K101 S10K175E2 175 225 3500 1500 35.0 0.40
B72214S2171K101 S14K175E2 175 225 6000 3000 70.0 0.60
B72220S2171K101 S20K175E2 175 225 10000 3000 135.0 1.00
VRMS = 210 V
B72205S2211K101 S05K210E2 210 270 800 150 9.5 0.10
B72207S2211K101 S07K210E2 210 270 1750 500 20.0 0.25
B72210S2211K101 S10K210E2 210 270 3500 1500 42.0 0.40
B72214S2211K101 S14K210E2 210 270 6000 3000 80.0 0.60
B72220S2211K101 S20K210E2 210 270 10000 3000 160.0 1.00
VRMS = 230 V
B72205S2231K101 S05K230E2 230 300 800 150 11.0 0.10
B72207S2231K101 S07K230E2 230 300 1750 500 23.0 0.25
B72210S2231K101 S10K230E2 230 300 3500 1500 45.0 0.40
B72214S2231K101 S14K230E2 230 300 6000 3000 90.0 0.60
B72220S2231K101 S20K230E2 230 300 10000 3000 180.0 1.00
1) Note: Nominal discharge current Inaccording to UL 1449, 4th edition.
Leaded varistors B722*
AdvanceD series
Page 3 of 35Please read Cautions and warnings and
Important notes at the end of this document.
Characteristics (TA=25°C)
Ordering code Vv
(1 mA)
V
∆Vv
(1 mA)
%
vc,max
(ic)
V
ic
A
Ctyp
(1 kHz)
pF
VRMS = 130 V
B72205S2131K101 205 ±10 340 5.0 135
B72207S2131K101 205 ±10 340 10.0 245
B72210S2131K101 205 ±10 340 25.0 500
B72214S2131K101 205 ±10 340 50.0 880
B72220S2131K101 205 ±10 340 100.0 1850
VRMS = 140 V
B72205S2141K101 220 ±10 360 5.0 125
B72207S2141K101 220 ±10 360 10.0 230
B72210S2141K101 220 ±10 360 25.0 470
B72214S2141K101 220 ±10 360 50.0 820
B72220S2141K101 220 ±10 360 100.0 1700
VRMS = 150 V
B72205S2151K101 240 ±10 395 5.0 115
B72207S2151K101 240 ±10 395 10.0 210
B72210S2151K101 240 ±10 395 25.0 430
B72214S2151K101 240 ±10 395 50.0 750
B72220S2151K101 240 ±10 395 100.0 1550
VRMS = 175 V
B72205S2171K101 270 ±10 455 5.0 100
B72207S2171K101 270 ±10 455 10.0 190
B72210S2171K101 270 ±10 455 25.0 380
B72214S2171K101 270 ±10 455 50.0 670
B72220S2171K101 270 ±10 455 100.0 1350
VRMS = 210 V
B72205S2211K101 330 ±10 545 5.0 75
B72207S2211K101 330 ±10 545 10.0 140
B72210S2211K101 330 ±10 545 25.0 290
B72214S2211K101 330 ±10 545 50.0 580
B72220S2211K101 330 ±10 545 100.0 1100
VRMS = 230 V
B72205S2231K101 360 ±10 595 5.0 70
B72207S2231K101 360 ±10 595 10.0 130
B72210S2231K101 360 ±10 595 25.0 265
B72214S2231K101 360 ±10 595 50.0 530
B72220S2231K101 360 ±10 595 100.0 1000
Leaded varistors B722*
AdvanceD series
Page 4 of 35Please read Cautions and warnings and
Important notes at the end of this document.
Electrical specifications and ordering codes
Maximum ratings (TA= 105 °C)
Ordering code Type
(untaped)
SIOV-
VRMS
V
VDC
V
imax
(8/20 µs)
1 time
A
In1)
(8/20 µs)
15 times
A
Wmax
(2 ms)
J
Pmax
W
VRMS = 250 V
B72205S2251K101 S05K250E2 250 320 800 150 12.0 0.10
B72207S2251K101 S07K250E2 250 320 1750 500 25.0 0.25
B72210S2251K101 S10K250E2 250 320 3500 1500 50.0 0.40
B72214S2251K101 S14K250E2 250 320 6000 3000 100.0 0.60
B72220S2251K101 S20K250E2 250 320 10000 3000 195.0 1.00
VRMS = 275 V
B72205S2271K101 S05K275E2 275 350 800 150 13.5 0.10
B72207S2271K101 S07K275E2 275 350 1750 500 27.5 0.25
B72210S2271K101 S10K275E2 275 350 3500 1500 55.0 0.40
B72214S2271K101 S14K275E2 275 350 6000 3000 110.0 0.60
B72220S2271K101 S20K275E2 275 350 10000 3000 215.0 1.00
VRMS = 300 V
B72205S2301K101 S05K300E2 300 385 800 150 15.0 0.10
B72207S2301K101 S07K300E2 300 385 1750 500 30.0 0.25
B72210S2301K101 S10K300E2 300 385 3500 1500 60.0 0.40
B72214S2301K101 S14K300E2 300 385 6000 3000 125.0 0.60
B72220S2301K101 S20K300E2 300 385 10000 3000 250.0 1.00
VRMS = 320 V
B72207S2321K101 S07K320E2 320 420 1750 500 32.0 0.25
B72210S2321K101 S10K320E2 320 420 3500 1500 67.0 0.40
B72214S2321K101 S14K320E2 320 420 6000 3000 136.0 0.60
B72220S2321K101 S20K320E2 320 420 10000 3000 273.0 1.00
VRMS = 350 V
B72210S2351K101 S10K350E2 350 460 3500 1500 67.0 0.40
B72214S2351K101 S14K350E2 350 460 5000 3000 136.0 0.60
B72220S2351K101 S20K350E2 350 460 10000 3000 273.0 1.00
VRMS = 385 V
B72210S2381K101 S10K385E2 385 505 3500 1500 67.0 0.40
B72214S2381K101 S14K385E2 385 505 5000 3000 136.0 0.60
B72220S2381K101 S20K385E2 385 505 10000 3000 273.0 1.00
1) Note: Nominal discharge current Inaccording to UL 1449, 4th edition.
Leaded varistors B722*
AdvanceD series
Page 5 of 35Please read Cautions and warnings and
Important notes at the end of this document.
Characteristics (TA=25°C)
Ordering code Vv
(1 mA)
V
∆Vv
(1 mA)
%
vc,max
(ic)
V
ic
A
Ctyp
(1 kHz)
pF
VRMS = 250 V
B72205S2251K101 390 ±10 650 5.0 65
B72207S2251K101 390 ±10 650 10.0 120
B72210S2251K101 390 ±10 650 25.0 245
B72214S2251K101 390 ±10 650 50.0 490
B72220S2251K101 390 ±10 650 100.0 940
VRMS = 275 V
B72205S2271K101 430 ±10 710 5.0 60
B72207S2271K101 430 ±10 710 10.0 110
B72210S2271K101 430 ±10 710 25.0 220
B72214S2271K101 430 ±10 710 50.0 440
B72220S2271K101 430 ±10 710 100.0 850
VRMS = 300 V
B72205S2301K101 470 ±10 775 5.0 55
B72207S2301K101 470 ±10 775 10.0 100
B72210S2301K101 470 ±10 775 25.0 200
B72214S2301K101 470 ±10 775 50.0 400
B72220S2301K101 470 ±10 775 100.0 780
VRMS = 320 V
B72207S2321K101 510 ±10 840 10.0 90
B72210S2321K101 510 ±10 840 25.0 185
B72214S2321K101 510 ±10 840 50.0 370
B72220S2321K101 510 ±10 840 100.0 720
VRMS = 350 V
B72210S2351K101 560 ±10 910 25.0 160
B72214S2351K101 560 ±10 910 50.0 350
B72220S2351K101 560 ±10 910 100.0 660
VRMS = 385 V
B72210S2381K101 620 ±10 1025 25.0 175
B72214S2381K101 620 ±10 1025 50.0 315
B72220S2381K101 620 ±10 1025 100.0 600
Leaded varistors B722*
AdvanceD series
Page 6 of 35Please read Cautions and warnings and
Important notes at the end of this document.
Electrical specifications and ordering codes
Maximum ratings (TA= 105 °C)
Ordering code Type
(untaped)
SIOV-
VRMS
V
VDC
V
imax
(8/20 µs)
1 time
A
In1)
(8/20 µs)
15 times
A
Wmax
(2 ms)
J
Pmax
W
VRMS = 420 V
B72210S2421K101 S10K420E2 420 560 3500 1500 67.0 0.40
B72214S2421K101 S14K420E2 420 560 5000 3000 136.0 0.60
B72220S2421K101 S20K420E2 420 560 10000 3000 273.0 1.00
VRMS = 460 V
B72210S2461K101 S10K460E2 460 615 3500 1500 70.0 0.40
B72214S2461K101 S14K460E2 460 615 5000 3000 150.0 0.60
B72220S2461K101 S20K460E2 460 615 10000 3000 300.0 1.00
VRMS = 510 V
B72210S2511K101 S10K510E2 510 670 3500 1500 80.0 0.40
B72214S2511K101 S14K510E2 510 670 5000 3000 165.0 0.60
B72220S2511K101 S20K510E2 510 670 10000 3000 325.0 1.00
VRMS = 550 V
B72210S2551K101 S10K550E2 550 745 3500 1500 90.0 0.40
B72214S2551K101 S14K550E2 550 745 5000 3000 180.0 0.60
B72220S2551K101 S20K550E2 550 745 10000 3000 360.0 1.00
VRMS = 625 V
B72210S2621K101 S10K625E2 625 825 3500 1500 100.0 0.40
B72214S2621K101 S14K625E2 625 825 5000 3000 200.0 0.60
B72220S2621K101 S20K625E2 625 825 10000 3000 400.0 1.00
VRMS = 680 V
B72210S2681K101 S10K680E2 680 895 3500 1500 110.0 0.40
B72214S2681K101 S14K680E2 680 895 5000 3000 220.0 0.60
B72220S2681K101 S20K680E2 680 895 10000 3000 440.0 1.00
1) Note: Nominal discharge current Inaccording to UL 1449, 4th edition.
Leaded varistors B722*
AdvanceD series
Page 7 of 35Please read Cautions and warnings and
Important notes at the end of this document.
Characteristics (TA=25°C)
Ordering code Vv
(1 mA)
V
∆Vv
(1 mA)
%
vc,max
(ic)
V
ic
A
Ctyp
(1 kHz)
pF
VRMS = 420 V
B72210S2421K101 680 ±10 1120 25.0 165
B72214S2421K101 680 ±10 1120 50.0 290
B72220S2421K101 680 ±10 1120 100.0 550
VRMS = 460 V
B72210S2461K101 750 ±10 1240 25.0 150
B72214S2461K101 750 ±10 1240 50.0 260
B72220S2461K101 750 ±10 1240 100.0 500
VRMS = 510 V
B72210S2511K101 820 ±10 1355 25.0 140
B72214S2511K101 820 ±10 1355 50.0 240
B72220S2511K101 820 ±10 1355 100.0 460
VRMS = 550 V
B72210S2551K101 910 ±10 1500 25.0 120
B72214S2551K101 910 ±10 1500 50.0 215
B72220S2551K101 910 ±10 1500 100.0 410
VRMS = 625 V
B72210S2621K101 1000 ±10 1650 25.0 110
B72214S2621K101 1000 ±10 1650 50.0 200
B72220S2621K101 1000 ±10 1650 100.0 380
VRMS = 680 V
B72210S2681K101 1100 ±10 1815 25.0 100
B72214S2681K101 1100 ±10 1815 50.0 180
B72220S2681K101 1100 ±10 1815 100.0 340
Leaded varistors B722*
AdvanceD series
Page 8 of 35Please read Cautions and warnings and
Important notes at the end of this document.
Dimensional drawings Weight
Nominal diameter
mm
VRMS
V
Weight
g
5 130 ... 300 0.4 ... 0.5
7 130 ... 320 0.6 ... 0.8
10 130 ... 680 1.2 ... 2.8
14 130 ... 680 1.8 ... 4.8
20 130 ... 680 3.3 ... 9.6
The weight of varistors in between these voltage
classes can be interpolated.
Dimensions
Ordering code [e] ± 1
mm
a (typical)
mm
wmax
mm
thmax
mm
hmax
mm
lmin
mm
d±0.05
mm
VRMS = 130 V
B72205S2131K101 5.0 1.6 7.0 3.9 8.5 25.0 0.6
B72207S2131K101 5.0 1.6 9.0 3.9 11.0 25.0 0.6
B72210S2131K101 7.5 1.8 12.0 4.5 14.5 25.0 0.8
B72214S2131K101 7.5 1.9 15.5 4.6 18.5 25.0 0.8
B72220S2131K101 10.0 2.0 21.5 5.0 25.5 25.0 1.0
VRMS = 140 V
B72205S2141K101 5.0 1.7 7.0 4.0 8.5 25.0 0.6
B72207S2141K101 5.0 1.7 9.0 4.0 11.0 25.0 0.6
B72210S2141K101 7.5 1.9 12.0 4.6 14.5 25.0 0.8
B72214S2141K101 7.5 2.0 15.5 4.7 18.5 25.0 0.8
B72220S2141K101 10.0 2.1 21.5 5.1 25.5 25.0 1.0
VRMS = 150 V
B72205S2151K101 5.0 1.8 7.0 4.1 8.5 25.0 0.6
B72207S2151K101 5.0 1.8 9.0 4.1 11.0 25.0 0.6
B72210S2151K101 7.5 2.0 12.0 4.7 14.5 25.0 0.8
B72214S2151K101 7.5 2.1 15.5 4.8 18.5 25.0 0.8
B72220S2151K101 10.0 2.2 21.5 5.2 25.5 25.0 1.0
VRMS = 175 V
B72205S2171K101 5.0 2.0 7.0 4.3 8.5 25.0 0.6
B72207S2171K101 5.0 2.0 9.0 4.3 11.0 25.0 0.6
B72210S2171K101 7.5 2.2 12.0 4.9 14.5 25.0 0.8
B72214S2171K101 7.5 2.2 15.5 4.9 18.5 25.0 0.8
B72220S2171K101 10.0 2.3 21.5 5.3 25.5 25.0 1.0
Leaded varistors B722*
AdvanceD series
Page 9 of 35Please read Cautions and warnings and
Important notes at the end of this document.
Ordering code [e] ± 1
mm
a (typical)
mm
wmax
mm
thmax
mm
hmax
mm
lmin
mm
d±0.05
mm
VRMS = 210 V
B72205S2211K101 5.0 1.7 7.0 4.2 8.5 25.0 0.6
B72207S2211K101 5.0 1.7 9.0 4.2 11.0 25.0 0.6
B72210S2211K101 7.5 1.9 12.0 5.0 14.5 25.0 0.8
B72214S2211K101 7.5 1.9 15.5 5.0 18.5 25.0 0.8
B72220S2211K101 10.0 2.2 21.5 5.4 25.5 25.0 1.0
VRMS = 230 V
B72205S2231K101 5.0 1.5 7.0 4.4 8.5 25.0 0.6
B72207S2231K101 5.0 1.5 9.0 4.4 11.0 25.0 0.6
B72210S2231K101 7.5 1.7 12.0 5.0 14.5 25.0 0.8
B72214S2231K101 7.5 1.7 15.5 5.1 18.5 25.0 0.8
B72220S2231K101 10.0 1.8 21.5 5.5 25.5 25.0 1.0
VRMS = 250 V
B72205S2251K101 5.0 1.5 7.0 4.5 8.5 25.0 0.6
B72207S2251K101 5.0 1.5 9.0 4.5 11.0 25.0 0.6
B72210S2251K101 7.5 1.7 12.0 5.2 14.5 25.0 0.8
B72214S2251K101 7.5 1.7 15.5 5.2 18.5 25.0 0.8
B72220S2251K101 10.0 1.9 21.5 5.7 25.5 25.0 1.0
VRMS = 275 V
B72205S2271K101 5.0 1.6 7.0 4.6 8.5 25.0 0.6
B72207S2271K101 5.0 1.6 9.0 4.6 11.0 25.0 0.6
B72210S2271K101 7.5 1.8 12.0 5.4 14.5 25.0 0.8
B72214S2271K101 7.5 1.8 15.5 5.4 18.5 25.0 0.8
B72220S2271K101 10.0 2.0 21.5 5.8 25.5 25.0 1.0
VRMS = 300 V
B72205S2301K101 5.0 1.7 7.0 4.7 8.5 25.0 0.6
B72207S2301K101 5.0 1.7 9.0 4.7 11.0 25.0 0.6
B72210S2301K101 7.5 1.9 12.0 5.6 14.5 25.0 0.8
B72214S2301K101 7.5 1.9 15.5 5.6 18.5 25.0 0.8
B72220S2301K101 10.0 2.1 21.5 6.1 25.5 25.0 1.0
VRMS = 320 V
B72207S2321K101 5.0 1.9 9.0 4.6 11.0 25.0 0.6
B72210S2321K101 7.5 2.1 12.0 5.8 15.0 25.0 0.8
B72214S2321K101 7.5 2.1 15.5 5.8 19.0 25.0 0.8
B72220S2321K101 10.0 2.3 21.5 6.2 25.5 25.0 1.0
Leaded varistors B722*
AdvanceD series
Page 10 of 35Please read Cautions and warnings and
Important notes at the end of this document.
Ordering code [e] ± 1
mm
a (typical)
mm
wmax
mm
thmax
mm
hmax
mm
lmin
mm
d±0.05
mm
VRMS = 350 V
B72210S2351K101 7.5 2.2 12.0 6.5 15.0 25.0 0.8
B72214S2351K101 7.5 2.2 15.5 6.5 19.0 25.0 0.8
B72220S2351K101 10.0 2.4 21.5 7.0 25.5 25.0 1.0
VRMS = 385 V
B72210S2381K101 7.5 2.4 12.0 7.1 15.0 25.0 0.8
B72214S2381K101 7.5 2.4 15.5 7.1 19.0 25.0 0.8
B72220S2381K101 10.0 2.5 21.5 7.6 26.0 25.0 1.0
VRMS = 420 V
B72210S2421K101 7.5 2.6 12.0 7.4 15.0 25.0 0.8
B72214S2421K101 7.5 2.6 15.5 7.5 19.0 25.0 0.8
B72220S2421K101 10.0 2.7 21.5 7.9 26.0 25.0 1.0
VRMS = 460 V
B72210S2461K101 7.5 2.8 12.0 7.7 15.0 25.0 0.8
B72214S2461K101 7.5 2.8 15.5 7.8 19.0 25.0 0.8
B72220S2461K101 10.0 3.0 21.5 8.2 26.0 25.0 1.0
VRMS = 510 V
B72210S2511K101 7.5 3.1 12.0 8.0 15.0 25.0 0.8
B72214S2511K101 7.5 3.1 15.5 8.1 19.0 25.0 0.8
B72220S2511K101 10.0 3.2 21.5 8.6 26.0 25.0 1.0
VRMS = 550 V
B72210S2551K101 7.5 3.4 12.0 8.4 15.0 25.0 0.8
B72214S2551K101 7.5 3.4 15.5 8.5 19.0 25.0 0.8
B72220S2551K101 10.0 3.6 21.5 9.0 26.0 25.0 1.0
VRMS = 625 V
B72210S2621K101 7.5 3.7 12.0 8.8 15.0 25.0 0.8
B72214S2621K101 7.5 3.7 15.5 8.9 19.0 25.0 0.8
B72220S2621K101 10.0 3.9 21.5 9.4 26.0 25.0 1.0
VRMS = 680 V
B72210S2681K101 7.5 4.1 12.0 9.2 15.0 25.0 0.8
B72214S2681K101 7.5 4.1 15.5 9.3 19.0 25.0 0.8
B72220S2681K101 10.0 4.2 21.5 9.8 26.0 25.0 1.0
Leaded varistors B722*
AdvanceD series
Page 11 of 35Please read Cautions and warnings and
Important notes at the end of this document.
Reliability data
Test Test methods/conditions Requirement
Varistor voltage The voltage between two terminals with
the specified measuring current applied
is called VV(1 mADC @ 0.2 ... 2 s).
To meet the specified value
Clamping voltage The maximum voltage between two
terminals with the specified standard
impulse current (8/20 µs) applied.
To meet the specified value
Endurance at upper
category temperature
1000 h at UCT
After having continuously applied the
maximum allowable AC voltage at UCT
±2°C for 1000 h, the specimen shall be
stored at room temperature and normal
humidity for 1 to 2 h.
Thereafter, the change of VVshall be
measured.
|∆V/V (1 mA)| ≤10%
Surge current derating,
8/20 µs
10 surge currents (8/20 µs), unipolar,
interval 30 s, amplitude corresponding
to derating curve for 10 impulses at
20 µs
|∆V/V (1 mA)| ≤10%
(measured in direction of
surge current)
No visible damage
Surge current derating,
2 ms
10 surge currents (2 ms), unipolar,
interval 120 s, amplitude corresponding
to derating curve for 10 impulses at
2 ms
|∆V/V (1 mA)| ≤10%
(measured in direction of
surge current)
No visible damage
Electric strength IEC 61051-1, test 4.9.2
Metal balls method, 2500 VRMS, 60 s
The varistor is placed in a container
holding 1.6 ±0.2 mm diameter metal
balls such that only the terminations of
the varistor are protruding.
The specified voltage shall be applied
between both terminals of the specimen
connected together and the electrode
inserted between the metal balls.
No breakdown
Leaded varistors B722*
AdvanceD series
Page 12 of 35Please read Cautions and warnings and
Important notes at the end of this document.
Test Test methods/conditions Requirement
Climatic sequence The specimen shall be subjected to:
a) dry heat at UCT, 16 h, IEC
60068-2-2, test Ba
b) damp heat, 1st cycle:
55 °C, 93% r. H., 24 h, IEC
60068-2-30, test Db
c) cold, LCT, 2 h, IEC 60068-2-1, test
Aa
d) damp heat, additional 5 cycles:
55 °C/25 °C, 93% r. H., 24 h/cycle,
IEC 60068-2-30, test Db.
Then the specimen shall be stored at
room temperature and normal humidity
for 1 to 2 h.
Thereafter, the change of VVshall be
measured. Thereafter, insulation resis-
tance Rins shall be measured at
V = 500 V.
|∆V/V (1 mA)| ≤10%
Rins ≥100 MΩ
Rapid change of
temperature
IEC 60068-2-14, test Na, LCT/UCT,
dwell time 30 min, 5 cycles
|∆V/V (1 mA)| ≤5%
No visible damage
Damp heat, steady state IEC 60068-2-78, test Ca
The specimen shall be subjected to
40 ±2°C, 90 to 95% r. H. for 56 days
without load / with 10% of the maxi-
mum continuous DC operating voltage
VDC. Then stored at room temperature
and normal humidity for 1 to 2 h.
Thereafter, the change of VVshall be
measured. Thereafter, insulation resis-
tance Rins shall be measured at
V = 500 V (insulated varistors only).
|∆V/V (1 mA)| ≤10%
Rins ≥100 MΩ
Leaded varistors B722*
AdvanceD series
Page 13 of 35Please read Cautions and warnings and
Important notes at the end of this document.
Test Test methods/conditions Requirement
Solderability IEC 60068-2-20, test Ta,
method 1 with modified conditions for
lead-free solder alloys: 245 °C, 3 s:
After dipping the terminals to a depth of
approximately 3 mm from the body in a
soldering bath of 245 °C for 3 s, the
terminals shall be visually examined.
The inspection shall be
carried out under adequate
light with normal eyesight or
with the assistance of a
magnifier capable of giving
a magnification of 4 to
10 times. The dipped
surface shall be covered
with a smooth and bright
solder coating with no more
than small amounts of
scattered imperfections
such as pinholes or
un-wetted or de-wetted
areas. These imperfections
shall not be concentrated in
one area.
Resistance to soldering
heat
IEC 60068-2-20, test Tb, method 1A,
260 °C, 10 s:
Each lead shall be dipped into a solder
bath having a temperature of 260 ±5°C
to a point 2.0 to 2.5 mm from the body
of the specimen, be held there for
10 ±1 s and then be stored at room
temperature and normal humidity for
1 to 2 h.
The change of VVshall be measured
and the specimen shall be visually
examined.
|∆V/V (1 mA)| ≤5%
No visible damage
Tensile strength IEC 60068-2-21, test Ua1
After gradually applying the force
specified below and keeping the unit
fixed for 10 s, the terminal shall be
visually examined for any damage.
Force for wire diameter:
0.6 mm = 10 N
0.8 mm = 10 N
1.0 mm = 20 N
|∆V/V (1 mA)| ≤5%
No break of solder joint,
no wire break
Leaded varistors B722*
AdvanceD series
Page 14 of 35Please read Cautions and warnings and
Important notes at the end of this document.
Test Test methods/conditions Requirement
Vibration IEC 60068-2-6, test Fc, method B4 |∆V/V (1 mA)| ≤5%
No visible damage
Frequency range:
Amplitude:
Duration:
Pulse:
10 … 55 Hz
0.75 mm or 98 m/s2
6h(3·2h)
sine wave
After repeatedly applying a single
harmonic vibration according to the
table above.
The change of VVshall be measured
and the specimen shall be visually
examined.
Bump IEC 60068-2-29, test Eb |∆V/V (1 mA)| ≤5%
No visible damage
Pulse duration:
Max. acceleration:
Number of bumps:
Pulse:
6 ms
400 m/s2
4000
half sine
Fire hazard IEC 60695-11-5 (needle flame test)
Severity: vertical 10 s
5 s max.
Note:
UCT = Upper category temperature
LCT = Lower category temperature
Rins = Insulation resistance
Leaded varistors B722*
AdvanceD series
Page 15 of 35Please read Cautions and warnings and
Important notes at the end of this document.
v/i characteristics
v = f (i) - for explanation of the characteristics refer to "General technical information", 1.6.3
A = Leakage current, B = Protection level } for worst-case varistor tolerances
SIOV-S05 ... E2
SIOV-S07 ... E2
Leaded varistors B722*
AdvanceD series
Page 16 of 35Please read Cautions and warnings and
Important notes at the end of this document.
v/i characteristics
v = f (i) - for explanation of the characteristics refer to "General technical information", 1.6.3
A = Leakage current, B = Protection level } for worst-case varistor tolerances
SIOV-S10 ... E2
Leaded varistors B722*
AdvanceD series
Page 17 of 35Please read Cautions and warnings and
Important notes at the end of this document.
v/i characteristics
v = f (i) - for explanation of the characteristics refer to "General technical information", 1.6.3
A = Leakage current, B = Protection level } for worst-case varistor tolerances
SIOV-S14 ... E2
Leaded varistors B722*
AdvanceD series
Page 18 of 35Please read Cautions and warnings and
Important notes at the end of this document.
v/i characteristics
v = f (i) - for explanation of the characteristics refer to "General technical information", 1.6.3
A = Leakage current, B = Protection level } for worst-case varistor tolerances
SIOV-S20 ... E2
Leaded varistors B722*
AdvanceD series
Page 19 of 35Please read Cautions and warnings and
Important notes at the end of this document.
Derating curves
Maximum surge current imax = f (tr, pulse train)
For explanation of the derating curves refer to "General technical information", section 1.8.1
SIOV-S05K130 ... K300E2
SIOV-S07K130 ... K320E2
Leaded varistors B722*
AdvanceD series
Page 20 of 35Please read Cautions and warnings and
Important notes at the end of this document.
Derating curves
Maximum surge current imax = f (tr, pulse train)
For explanation of the derating curves refer to "General technical information", section 1.8.1
SIOV-S10K130 ... K320E2
SIOV-S10K350 ... K680E2
Leaded varistors B722*
AdvanceD series
Page 21 of 35Please read Cautions and warnings and
Important notes at the end of this document.
Derating curves
Maximum surge current imax = f (tr, pulse train)
For explanation of the derating curves refer to "General technical information", section 1.8.1
SIOV-S14K130 ... K320E2
SIOV-S14K350 ... K680E2
Leaded varistors B722*
AdvanceD series
Page 22 of 35Please read Cautions and warnings and
Important notes at the end of this document.
Derating curves
Maximum surge current imax = f (tr, pulse train)
For explanation of the derating curves refer to "General technical information", section 1.8.1
SIOV-S20K130 ... K320E2
SIOV-S20K350 ... K680E2
Leaded varistors B722*
AdvanceD series
Page 23 of 35Please read Cautions and warnings and
Important notes at the end of this document.
Taping, packaging and lead configuration
1 EPCOS ordering code system
For leaded varistors
B722 or B723 10 S 2 271 K 1 0 1
Monolithic
varistor
Nominal
disc diameter
Design:
F = Fail-safe varistor
Q = EnergetiQ
S=Leaded varistor
T = ThermoFuse
U = Disk type, SNF
X = Disk type, SNF (AEC-Q200)
Series:
0 = StandarD
1 = Automotive
2 = AdvanceD
3 = SuperioR
4 = SuperioR
Max. AC operating voltage:
271 = 27 101= 275 VAC
140 = 14 100= 14 VAC
141 = 14 101= 140 VAC
Tolerance of varistor voltage:
K=±10%
J=±5%
S = Special tolerance
Lead configuration:
1 = Straight leads
2 thru 9 = Kinked form
Packaging:
0 = Bulk,
1 thru 7 = Taping style
Internal coding:
1 = Standard
Leaded varistors B722*
AdvanceD series
Page 24 of 35Please read Cautions and warnings and
Important notes at the end of this document.
2 Taping and packaging of leaded varistors
Tape packaging for lead spacing = 5 fully conforms to IEC 60286-2, while for lead spacings
= 7.5 and 10 the taping mode is based on this standard.
2.1 Taping in accordance with IEC 60286-2 for lead spacing 5.0 mm
2.2 Taping based on IEC 60286-2 for lead spacing 7.5 and 10 mm
Leaded varistors B722*
AdvanceD series
Page 25 of 35Please read Cautions and warnings and
Important notes at the end of this document.
2.3 Tape dimensions (in mm)
Sym-
bol
= 5.0 Tolerance = 7.5 Tolerance = 10.0 Tolerance Remarks
w max. max. max. see tables in
each series
th max. max. max. under
"Dimensions"
d 0.6 ±0.05 0.8 ±0.05 1.0 ±0.05
P012.7 ±0.3 12.71) ±0.3 12.7 ±0.3 ±1 mm/20
sprocket holes
P13.85 ±0.7 8.95 ±0.8 7.7 ±0.8
F 5.0 +0.6/0.1 7.5 ±0.8 10.0 ±0.8
∆h 0 ±2.0 depends on s depends on s measured at
∆p 0 ±1.3 0 ±2.0 0 ±2.0 top of compo-
nent body
W 18.0 ±0.5 18.0 ±0.5 18.0 ±0.5
W05.5 min. 11.0 min. 11.0 min. Peel-off
force > 5 N
W19.0 ±0.5 9.0 +0.75/0.5 9.0 +0.75/0.5
W23.0 max. 3.0 max. 3.0 max.
H 18.0 +2.0/0 18.0 +2.0/0 18.0 +2.0/02)
H016.0
(18.0) ±0.5 16.0
(18.0) ±0.5 16.0 ±0.5 3)
H132.2 max. 45.0 max. 45.0 max.
D04.0 ±0.2 4.0 ±0.2 4.0 ±0.2
t 0.9 max. 0.9 max. 0.9 max. without lead
L 11.0 max. 11.0 max. 11.0 max.
L10.5 max.
1) Taping with P0= 15.0 mm upon request
2) Applies only to uncrimped types
3) Applies only to crimped types (H0= 18 upon request)
Leaded varistors B722*
AdvanceD series
Page 26 of 35Please read Cautions and warnings and
Important notes at the end of this document.
2.4 Taping mode
Example: B72210S0271K1 51
|
Digit 14
Digit 14 Taping
mode
Reel type Seating plane height H0
for crimped types
mm
Seating plane height H
for uncrimped types
mm
Pitch distance
P0
mm
0Bulk
1 G I 16 18 12.7
2 G2 I 18 12.7
3 G3 II 16 18 12.7
4 G4 II 18 12.7
5 G5 III 16 18 12.7
6 GA Ammo pack 16 18 12.7
7 G2A Ammo pack 18 12.7
Internal coding for special taping
G6 III 18 12.7
G10 II 16 18 15.0
G11 II 18 15.0
G10A Ammo pack 16 18 15.0
G11A Ammo pack 18 15.0
2.5 Reel dimension
Dimensions (in mm)
Reel type d f n w
I 360 max. 31 ±1 approx. 45 54 max.
II 360 max. 31 ±1 approx. 55 64 max.
III 500 max. 23 ±1 approx. 59 72 max.
If reel type III is not compatible with insertion equipment because of its large diameter, nominal
disk diameter 10 mm and 14 mm can be supplied on reel II upon request (taping mode G3).
Leaded varistors B722*
AdvanceD series
Page 27 of 35Please read Cautions and warnings and
Important notes at the end of this document.
2.6 Ammo pack dimensions
3 Lead configuration
Straight leads are standard for disk varistors. Other lead configurations as crimp style or cus-
tomer-specific lead wire length according to 3.1, 3.2, 3.3 and 3.4 are optional. Crimped leads
(non-standard) are differently crimped for technical reasons; the individual crimp styles are denot-
ed by consecutive numbers (S, S2 through S5) as shown in the dimensional drawings below.
The crimp styles of the individual types can be seen from the type designation in the ordering ta-
bles.
3.1 Crimp style mode
Example: B72210S0271K 501
|
Digit 13
Digit 13 of ordering code Crimp style Figure
1 Standard, straight leads 1
2 S2 2
3 S3 3
5 S5 4
Available upon request
Internal coding 5
Leaded varistors B722*
AdvanceD series
Page 28 of 35Please read Cautions and warnings and
Important notes at the end of this document.
3.2 Standard leads and non-standard crimp styles
The basic dimensions in figure 1 to 5 are valid for types with either round or square
(EnergetiQ series) component head.
Standard, straight leads Non-standard,
crimp style S2
Non-standard,
crimp style S3
Figure 1 Figure 2 Figure 3
Non-standard, crimp style S5
Figure 4
Leaded varistors B722*
AdvanceD series
Page 29 of 35Please read Cautions and warnings and
Important notes at the end of this document.
3.3 Trimmed leads (non-standard)
Varistors with cut leads available upon request.
Lead length tolerances:
Straight leads +/0.8 mm
Crimped leads +/0.5 mm
Minimum lead length 3.0 mm
Figure 5
Leaded varistors B722*
AdvanceD series
Page 30 of 35Please read Cautions and warnings and
Important notes at the end of this document.
Cautions and warnings
General
1. EPCOS metal oxide varistors are designed for specific applications and should not be used
for purposes not identified in our specifications, application notes and data books unless oth-
erwise agreed with EPCOS during the design-in-phase.
2. Ensure suitability of SIOVs through reliability testing during the design-in phase. SIOVs
should be evaluated taking into consideration worst-case conditions.
3. For applications of SIOVs in line-to-ground circuits based on various international and local
standards there are restrictions existing or additional safety measures required.
Storage
1. Store SIOVs only in original packaging. Do not open the package prior to processing.
2. Recommended storage conditions in original packaging:
Storage temperature: 25 °C ... +45 °C,
Relative humidity: <75% annual average,
<95% on maximum 30 days a year.
Dew precipitation: is to be avoided.
3. Avoid contamination of an SIOV's during storage, handling and processing.
4. Avoid storage of SIOVs in harmful environments that can affect the function during long-term
operation (examples given under operation precautions).
5. The SIOV type series should be soldered after shipment from EPCOS within the time speci-
fied:
SIOV-S, -Q, -LS, -B, -SNF 24 months
ETFV/ T series, -CU 12 months.
Handling
1. SIOVs must not be dropped.
2. Components must not be touched with bare hands. Gloves are recommended.
3. Avoid contamination of the surface of SIOV electrodes during handling, be careful of the
sharp edge of SIOV electrodes.
Soldering (where applicable)
1. Use rosin-type flux or non-activated flux.
2. Insufficient preheating may cause ceramic cracks.
3. Rapid cooling by dipping in solvent is not recommended.
4. Complete removal of flux is recommended.
5. Temperatures of all preheat stages and the solder bath must be strictly controlled especially
for T series (T14 and T20).
Leaded varistors B722*
AdvanceD series
Page 31 of 35Please read Cautions and warnings and
Important notes at the end of this document.
Mounting
1. Potting, sealing or adhesive compounds can produce chemical reactions in the SIOV ceramic
that will degrade the component’s electrical characteristics.
2. Overloading SIOVs may result in ruptured packages and expulsion of hot materials. For this
reason SIOVs should be physically shielded from adjacent components.
Operation
1. Use SIOVs only within the specified temperature operating range.
2. Use SIOVs only within the specified voltage and current ranges.
3. Environmental conditions must not harm SIOVs. Use SIOVs only in normal atmospheric con-
ditions. Avoid use in deoxidizing gases (chlorine gas, hydrogen sulfide gas, ammonia gas,
sulfuric acid gas etc), corrosive agents, humid or salty conditions.Contact with any liquids and
solvents should be prevented.
Display of ordering codes for EPCOS products
The ordering code for one and the same EPCOS product can be represented differently in data
sheets, data books, other publications, on the EPCOS website, or in order-related documents
such as shipping notes, order confirmations and product labels. The varying representations of
the ordering codes are due to different processes employed and do not affect the
specifications of the respective products. Detailed information can be found on the Internet
under www.epcos.com/orderingcodes
Leaded varistors B722*
AdvanceD series
Page 32 of 35Please read Cautions and warnings and
Important notes at the end of this document.
Symbols and terms
Symbol Term
C Capacitance
Ctyp Typical capacitance
i Current
icCurrent at which Vc, max is measured
Ileak Leakage current
imax Maximum surge current (also termed peak current)
Imax Maximum discharge current
InNominal discharge current to UL 1449
LCT Lower category temperature
Ltyp Typical inductance
Pmax Maximum average power dissipation
Rins Insulation resistance
Rmin Minimum resistance
TAAmbient temperature
trDuration of equivalent rectangular wave
UCT Upper category temperature
v Voltage
Vclamp Clamping voltage
vc, max Maximum clamping voltage at specified current ic
VDC DC operating voltage
Vjump Maximum jump start voltage
vmax Maximum voltage
Vop Operating voltage
VRMS AC operating voltage, root-mean-square value
VRMS, op, max Root-mean-square value of max. DC operating voltage incl. ripple current
Vsurge Super imposed surge voltage
VVVaristor voltage
∆VVTolerance of varistor voltage
WLD Maximum load dump
Wmax Maximum energy absorption
Lead spacing
All dimensions are given in mm.
The commas used in numerical values denote decimal points.
Leaded varistors B722*
AdvanceD series
Page 33 of 35Please read Cautions and warnings and
Important notes at the end of this document.
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical re-
quirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar
with them than the customers themselves. For these reasons, it is always ultimately incum-
bent on the customer to check and decide whether an EPCOS product with the properties de-
scribed in the product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in
which the malfunction or failure of an electronic component could endanger human life or
health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by
means of suitable design of the customer application or other action taken by the customer
(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by
third parties in the event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our Ma-
terial Data Sheets on the Internet (www.epcos.com/material). Should you have any more de-
tailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order. We also
reserve the right to discontinue production and delivery of products. Consequently, we
cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in the case of individual agreements deviating from the fore-
going for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current ver-
sion of the "General Terms of Delivery for Products and Services in the Electrical In-
dustry" published by the German Electrical and Electronics Industry Association
(ZVEI).
Important notes
Page 34 of 35
7. The trade names EPCOS, CeraCharge, CeraDiode, CeraLink, CeraPad, CeraPlas, CSMP,
CTVS, DeltaCap, DigiSiMic, ExoCore, FilterCap, FormFit, LeaXield, MiniBlue, MiniCell, MKD,
MKK, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, PowerHap, PQSine,
PQvar, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV,
ThermoFuse, WindCap are trademarks registered or pending in Europe and in other coun-
tries. Further information will be found on the Internet at www.epcos.com/trademarks.
Important notes
Page 35 of 35
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
EPCOS:
B72242E0302R001 B72242E0602R001 B72232E0602R001 B72232E0302R001
EPCOS / TDK:
B72205S950K111 B72205S950K211 B72214S511K501 B72214S681K301 B72214S950K551 B72210S500K531
B72214S511K301 B72210S950K151 B72220S750K551 B72210S621K101 B72214S681K331 B72220S511K501
B72220S500K551 B72220S600K551 B72210S621K331 B72214S551K301 B72214S750K551 B72214S511K131
B72214S551K331 B72210S600K151 B72210S950K551 B72214S500K551 B72214S621K101 B72214S511K331
B72220S681K101 B72214S950K151 B72214S500K151 B72214S551K101 B72205S600K101 B72214S600K501
B72210S750K551 B72214S600K551 B72214S681K351 B72210S500K151 B72210S621K351 B72214S621K351
B72207S600K111 B72207S500K211 B72214S600K151 B72214S750K151 B72214S511K101 B72207S950K111
B72205S600K311 B72205S750K211 B72205S600K211 B72207S600K311 B72207S500K311 B72205S500K211
B72205S500K111 B72207S600K211 B72210S750K151 B72210S681K351 B72210S600K501 B72210S600K551
B72207S750K211
