SMSC LAN8700/LAN8700i PRODUCT PREVIEW Revision 2.3 (04-12-11)
Data Brief
PRODUCT FEATURES
LAN8700/LAN8700i
±15kV ESD Protected MII/RMII
10/100 Ethernet Transceiver with HP
Auto-MDIX Support and flexPWR®
Technology in a Small Footprint
Single-Chip Ethernet Physical Layer Transceiver
(PHY)
ESD Protection levels of ±8kV HBM without external
protection devices
ESD protection levels of IEC61000-4-2, ±8kV contact
mode, and ±15kV for air discharge mode per
independent test facility
Comprehensive flexPWR® Technology
— Flexible Power Management Architecture
LVCMOS Variable I/O voltage range: +1.6V to +3.6V
Integrated 3.3V to 1.8V regulator for optional single
supply operation.
— Regulator can be disabled if 1.8V system supply is
available.
Performs HP Auto-MDIX in accordance with IEEE
802.3ab specification
Cable length greater than 150 meters
Automatic Polarity Correction
Latch-Up Performance Exceeds 150mA per
EIA/JESD 78, Class II
Energy Detect power-down mode
Low Current consumption power down mode
Low operating current consumption:
— 39mA typical in 10BASE-T and
— 79mA typical in 100BASE-TX mode
Supports Auto-negotiation and Parallel Detection
Supports the Media Independent Interface (MII) and
Reduced Media Independent Interface (RMII)
Compliant with IEEE 802.3-2005 standards
— MII Pins tolerant to 3.6V
IEEE 802.3-2005 compliant register functions
Integrated DSP with Adaptive Equalizer
Baseline Wander (BLW) Correction
Vendor Specific register functions
Low profile 36-pin QFN lead-free RoHS compliant
package (6 x 6 x 0.9mm height)
4 LED status indicators
Commercial Operating Temperature 0° C to 70° C
Industrial Operating Temperature -40° C to 85° C
version available (LAN8700i)
Applications
Set Top Boxes
Network Printers and Servers
LAN on Motherboard
10/100 PCMCIA/CardBus Applications
Embedded Telecom Applications
Video Record/Playback Systems
Cable Modems/Routers
DSL Modems/Routers
Digital Video Recorders
Personal Video Recorders
IP and Video Phones
Wireless Access Points
Digital Televisions
Digital Media Adaptors/Servers
POS Terminals
Automotive Networking
Gaming Consoles
Security Systems
POE Applications
Access Control
Order Numbers:
LAN8700C-AEZG for 36-pin, QFN lead-free RoHS compliant package
LAN8700iC-AEZG for (Industrial Temp) 36-pin, QFN lead-free RoHS compliant package
4900 pcs per tray
LAN8700C-AEZG-TR for 36-pin, QFN lead-free RoHS compliant package (tape and reel)
3000 pcs per reel
This product meets the halogen maximum concentration values per IEC61249-2-21
For RoHS compliance and environmental information, please visit www.smsc.com/rohs
80 ARKAY DRIVE, HAUPPAUGE, NY 11788 (631) 435-6000 or 1 (800) 443-SEMI
Copyright © 2011 SMSC or its subsidiaries. All rights reserved.
Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for
construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC
reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office to obtain the latest specifications
before placing your product order. The provision of this information does not convey to the purchaser of the described semiconductor devices any licenses under any patent
rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated
version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors
known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC products are not
designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property
damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of
this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC’s website at http://www.smsc.com. SMSC is a registered
trademark of Standard Microsystems Corporation (“SMSC”). Product names and company names are the trademarks of their respective holders.
SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE
OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL
DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT;
TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD
TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
±15kV ESD Protected MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support and flexPWR® Technology in a Small Footprint
Revision 2.3 (04-12-11) 2 SMSC LAN8700/LAN8700i
PRODUCT PREVIEW
±15kV ESD Protected MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support and flexPWR® Technology in a Small Footprint
SMSC LAN8700/LAN8700i 3 Revision 2.3 (04-12-11)
PRODUCT PREVIEW
General Description
The SMSC LAN8700/LAN8700i is a low-power, industrial temperature (LAN8700i), variable I/O voltage,
analog interface IC with HP Auto-MDIX support for high-performance embedded Ethernet applications.
The LAN8700/LAN8700i can be configured to operate on a single 3.3V supply utilizing an integrated
3.3V to 1.8V linear regulator. An option is available to disable the linear regulator to optimize system
designs that have a 1.8V power plane available.
0.1 Architectural Overview
The LAN8700/LAN8700i consists of an encoder/decoder, scrambler/descrambler, wave-shaping
transmitter, output driver, twisted-pair receiver with adaptive equalizer and baseline wander (BLW)
correction, and clock and data recovery functions. The LAN8700/LAN8700i can be configured to
support either the Media Independent Interface (MII) or the Reduced Media Independent Interface
(RMII).
The LAN8700/LAN8700i is compliant with IEEE 802.3-2005 standards (MII Pins tolerant to 3.6V) and
supports both IEEE 802.3-2005 compliant and vendor-specific register functions. It contains a full-
duplex 10-BASE-T/100BASE-TX transceiver and supports 10-Mbps (10BASE-T) operation on
Category 3 and Category 5 unshielded twisted-pair cable, and 100-Mbps (100BASE-TX) operation on
Category 5 unshielded twisted-pair cable.
Hubs and switches with multiple integrated MACs and external PHYs can have a large pin count due
to the high number of pins needed for each MII interface. An increasing pin count causes increasing
cost.
The RMII interface is intended for use on Switch based ASICs or other embedded solutions requiring
minimal pincount for ethernet connectivity. RMII requires only 6 pins for each MAC to PHY interface
plus one common reference clock. The MII requires 16 pins for each MAC to PHY interface.
The SMSC LAN8700/LAN8700i is capable of running in RMII mode. Please contact your SMSC sales
representative for the latest RMII specification.
The LAN8700/LAN8700i referenced throughout this document applies to both the commercial
temperature and industrial temperature components. The LAN8700i refers to only the industrial
temperature component.
Figure 1 LAN8700/LAN8700i System Block Diagram
10/100
Media
Access
Controller
(MAC)
or SOC
SMSC
LAN8700/
LAN8700i
Magnetics Ethernet
System Bus
LEDS/GPIO
25 MHz (MII) or 50MHz (RMIII)
Crystal or External Clock
MII /RMII
±15kV ESD Protected MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support and flexPWR® Technology in a Small Footprint
Revision 2.3 (04-12-11) 4 SMSC LAN8700/LAN8700i
PRODUCT PREVIEW
Figure 2 LAN8700/LAN8700i Architectural Overview
10M Rx
Logic
100M Rx
Logic
DSP System:
Clock
Data Recovery
Equalizer
Analog-to-
Digital
100M PLL
Squelch &
Filters
10M PLL
Receive Section
Central
Bias
HP Auto-MDIX
Management
Control
SMI
RMII / MII Logic
TXP / TXN
TXD[0..3]
TX_EN
TX_ER
TX_CLK
RXD[0..3]
RX_DV
RX_ER
RX_CLK
CRS
COL/CRS_DV
MDC
MDIO
SPEED100
LINK
ACTIVITY
FDUPLEX
LED Circuitry
MODE Control
nINT
nRST RXP / RXN
10M Tx
Logic
10M
Transmitter
100M Tx
Logic
100M
Transmitter
Transmit Section
PLL XTAL1
XTAL2
MODE0
MODE1
MODE2
PHY
Address
Latches
PHYAD[0..4]
Auto-
Negotiation
Interrupt
Generator
MII
MDIX
Control
±15kV ESD Protected MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support and flexPWR® Technology in a Small Footprint
SMSC LAN8700/LAN8700i 5 Revision 2.3 (04-12-11)
PRODUCT PREVIEW
Pin Diagram
Figure 3 LAN8700/LAN8700i Package Pin Diagram (Top View)
nINT/TX_ER/TXD4
MDC
CRS/PHYAD4
MDIO
nRST
TX_EN
VDD_CORE
VDD33
LINK/PHYAD1
ACTIVITY/PHYAD2
FDUPLEX/PHYAD3
XTAL2
CLKIN/XTAL1
RXD3/nINTSEL
RXD1/MODE1
RXD2/MODE2
TXD3
RX_CLK/REGOFF
TX_CLK
RX_ER/RXD4
VDDIO
TXD1
TXD0
TXD2
COL/RMII/CRS_DV
TXP
RXN
VDDA3.3
EXRES1
VDDA3.3
RXP
VDDA3.3
1
2
3
4
5
6
7
8
LAN8700/LAN8700i
MII/RMII Ethernet PHY
36 Pin QFN
GND FLAG
10
11
12
13
14
15
16
24
23
22
21
20
19
32
31
30
29
28
SPEED100/PHYAD0 9RX_DV
RXD0/MODE0
17
TXN
18
27
26
25
36
35
34
33
±15kV ESD Protected MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support and flexPWR® Technology in a Small Footprint
Revision 2.3 (04-12-11) 6 SMSC LAN8700/LAN8700i
PRODUCT PREVIEW
Table 1 LAN8700/LAN8700i 36-PIN QFN Pinout
PIN NO. PIN NAME PIN NO. PIN NAME
1 nINT/TX_ER/TXD4 19 RX_DV
2 MDC 20 RX_CLK/REGOFF
3 CRS/PHYAD4 21 RX_ER/RXD4
4MDIO22 TXCLK
5nRST23 TXD0
6 TX_EN 24 TXD1
7 VDD33 25 VDDIO
8VDD_CORE26 TXD2
9 SPEED100/PHYAD0 27 TXD3
10 LINK/PHYAD1 28 TXN
11 ACTIVITY/PHYAD2 29 TXP
12 FDUPLEX/PHYAD3 30 VDDA3.3
13 XTAL2 31 RXN
14 CLKIN/XTAL1 32 RXP
15 RXD3/nINTSEL 33 VDDA3.3
16 RXD2/MODE2 34 EXRES1
17 RXD1/MODE1 35 VDDA3.3
18 RXD0/MODE0 36 COL/MII/CRS_DV
±15kV ESD Protected MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support and flexPWR® Technology in a Small Footprint
SMSC LAN8700/LAN8700i 7 Revision 2.3 (04-12-11)
PRODUCT PREVIEW
Pin Description
This section describes the signals on each pin. When a lower case “n” is used at the beginning of the
signal name, it indicates that the signal is active low. For example, nRST indicates that the reset signal
is active low.
I/O Signals
I Input. Digital LVCMOS levels.
O Output. Digital LVCMOS levels.
I/O Input or Output. Digital LVCMOS levels.
Note: The digital signals are not 5V tolerant.They are variable voltage from +1.6V to +3.6V.
AI Input. Analog levels.
AO Output. Analog levels.
Table 2 MII Signals
SIGNAL NAME TYPE DESCRIPTION
TXD0 I Transmit Data 0: Bit 0 of the 4 data bits that are accepted by
the PHY for transmission.
TXD1 I Transmit Data 1: Bit 1 of the 4 data bits that are accepted by
the PHY for transmission.
TXD2 I Transmit Data 2: Bit 2 of the 4 data bits that are accepted by
the PHY for transmission
Note: This signal should be grounded in RMII Mode.
TXD3 I Transmit Data 3: Bit 3 of the 4 data bits that are accepted by
the PHY for transmission.
Note: This signal should be grounded in RMII Mode
nINT/
TX_ER/
TXD4
I/O MII Transmit Error: When driven high, the 4B/5B encode
process substitutes the Transmit Error code-group (/H/) for the
encoded data word. This input is ignored in 10Base-T operation.
MII Transmit Data 4: In Symbol Interface (5B Decoding) mode,
this signal becomes the MII Transmit Data 4 line, the MSB of the
5-bit symbol code-group.
Notes:
This signal is not used in RMII Mode.
This signal is mux’d with nINT
TX_EN I Transmit Enable: Indicates that valid data is presented on the
TXD[3:0] signals, for transmission. In RMII Mode, only TXD[1:0]
have valid data.
TX_CLK O Transmit Clock: 25MHz in 100Base-TX mode. 2.5MHz in
10Base-T mode.
Note: This signal is not used in RMII Mode
RXD0/
MODE0
I/O Receive Data 0: Bit 0 of the 4 data bits that are sent by the PHY
in the receive path.
PHY Operating Mode Bit 0: set the default MODE of the PHY.
±15kV ESD Protected MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support and flexPWR® Technology in a Small Footprint
Revision 2.3 (04-12-11) 8 SMSC LAN8700/LAN8700i
PRODUCT PREVIEW
RXD1/
MODE1
I/O Receive Data 1: Bit 1 of the 4 data bits that are sent by the PHY
in the receive path.
PHY Operating Mode Bit 1: set the default MODE of the PHY.
RXD2/
MODE2
I/O Receive Data 2: Bit 2 of the 4 data bits that are sent by the PHY
in the receive path.
PHY Operating Mode Bit 2: set the default MODE of the PHY.
Notes:
RXD2 is not used in RMII Mode.
RXD3/
nINTSEL
I/O Receive Data 3: Bit 3 of the 4 data bits that are sent by the PHY
in the receive path.
nINTSEL: On power-up or external reset, the mode of the
nINT/TXER/TXD4 pin is selected.
When RXD3/nINTSEL is floated or pulled to VDDIO, nINT is
selected for operation on pin nINT/TXER/TXD4 (default).
When RXD3/nINTSEL is pulled low to VSS through a resistor,
TXER/TXD4 is selected for operation on pin nINT/TXER/TXD4.
Notes:
RXD3 is not used in RMII Mode
If the nINT/TXER/TXD4 pin is configured for nINT mode, then
a pull-up resistor is needed to VDDIO on the nINT/TXER/TXD4
pin.
RX_ER/
RXD4/
OReceive Error: Asserted to indicate that an error was detected
somewhere in the frame presently being transferred from the
PHY.
MII Receive Data 4: In Symbol Interface (5B Decoding) mode,
this signal is the MII Receive Data 4 signal, the MSB of the
received 5-bit symbol code-group. Unless configured in this
mode, the pin functions as RX_ER.
Note: This pin has an internal pull-down resistor, and must not
be high during reset. The RX_ER signal is optional in
RMII Mode.
RX_DV O Receive Data Valid: Indicates that recovered and decoded data
nibbles are being presented on RXD[3:0].
Note: This pin has an internal pull-down resistor, and must not
be high during reset. This signal is not used in RMII
Mode.
RX_CLK/
REGOFF
I/O Receive Clock: In MII mode, this pin is the receive clock output.
25MHz in 100Base-TX mode. 2.5MHz in 10Base-T mode.
Note: This signal is not used in RMII Mode.
Regulator Off: This pin may be used to configure the internal
1.8V regulator off. This pin is sampled during the power-on
sequence to determine if the internal regulator should turn on.
When the regulator is disabled, external 1.8V must be supplied
to VDD_CORE, and the voltage at VDD33 must be at least
2.64V before voltage is applied to VDD_CORE.
Table 2 MII Signals (continued)
SIGNAL NAME TYPE DESCRIPTION
±15kV ESD Protected MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support and flexPWR® Technology in a Small Footprint
SMSC LAN8700/LAN8700i 9 Revision 2.3 (04-12-11)
PRODUCT PREVIEW
COL/
RMII/
CRS_DV
I/O MII Mode Collision Detect: Asserted to indicate detection of
collision condition.
RMII – MII/RMII mode selection is latched on the rising edge of
the internal reset (nreset) based on the following strapping:
Float this pin for MII mode or pull-high with an external resistor
to VDDIO to set the device in RMII mode.
RMII Mode CRS_DV (Carrier Sense/Receive Data Valid)
Asserted to indicate when the receive medium is non-idle. When
a 10BT packet is received, CRS_DV is asserted, but RXD[1:0] is
held low until the SFD byte (10101011) is received. In 10BT, half-
duplex mode, transmitted data is not looped back onto the
receive data pins, per the RMII standard.
CRS/
PHYAD4
I/O Carrier Sense: Indicates detection of carrier.
Note: This signal is mux’d with PHYAD4
Table 3 LED Signals
SIGNAL NAME TYPE DESCRIPTION
SPEED100/
PHYAD0
I/O LED1 – SPEED100 indication. Active indicates that the selected
speed is 100Mbps. Inactive indicates that the selected speed is
10Mbps.
Note: This signal is mux’d with PHYAD0
LINK/
PHYAD1
I/O LED2 – LINK ON indication. Active indicates that the Link
(100Base-TX or 10Base-T) is on.
Note: This signal is mux’d with PHYAD1
ACTIVITY/
PHYAD2
I/O LED3 – ACTIVITY indication. Active indicates that there is
Carrier sense (CRS) from the active PMD.
Note: This signal is mux’d with PHYAD2
FDUPLEX/
PHYAD3
I/O LED4 – DUPLEX indication. Active indicates that the PHY is in
full-duplex mode.
Note: This signal is mux’d with PHYAD3
Table 4 Management Signals
SIGNAL NAME TYPE DESCRIPTION
MDIO I/O Management Data Input/OUTPUT: Serial management data
input/output.
MDC I Management Clock: Serial management clock.
Table 2 MII Signals (continued)
SIGNAL NAME TYPE DESCRIPTION
±15kV ESD Protected MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support and flexPWR® Technology in a Small Footprint
Revision 2.3 (04-12-11) 10 SMSC LAN8700/LAN8700i
PRODUCT PREVIEW
Note 1 On nRST transition high, the PHY latches the state of the configuration pins in this table.
Table 5 Boot Strap Configuration Inputs (Note 1)
SIGNAL NAME TYPE DESCRIPTION
CRS/
PHYAD4
I/O PHY Address Bit 4: set the default address of the PHY. This
signal is mux’d with CRS
Note: This signal is mux’d with CRS
FDUPLEX/
PHYAD3
I/O PHY Address Bit 3: set the default address of the PHY.
Note: This signal is mux’d with FDUPLEX
ACTIVITY/
PHYAD2
I/O PHY Address Bit 2: set the default address of the PHY.
Note: This signal is mux’d with ACTIVITY
LINK/
PHYAD1
I/O PHY Address Bit 1: set the default address of the PHY.
Note: This signal is mux’d with LINK
SPEED100/
PHYAD0
I/O PHY Address Bit 0: set the default address of the PHY.
Note: This signal is mux’d with SPEED100
RXD2/
MODE2
I/O PHY Operating Mode Bit 2: set the default MODE of the PHY.
Note: This signal is mux’d with RXD2
RXD1/
MODE1
I/O PHY Operating Mode Bit 1: set the default MODE of the PHY.
Note: This signal is mux’d with RXD1
RXD0/
MODE0
I/O PHY Operating Mode Bit 0: set the default MODE of the PHY.
Note: This signal is mux’d with RXD0
RX_CLK/
REGOFF
I/O Internal Regulator off: disable the internal +1.8v regulator.
This signal is mux’d with RX_CLK.
Float to enable the internal +1.8v regulator.
Pull up with a resistor to VDDIO to disable the internal
regulator.
COL/
RMII/
CRS_DV
I/O Digital Communication Mode: set the digital communications
mode of the PHY to RMII or MII. This signal is muxed with the
Collision signal (MII mode) and Carrier Sense/ receive Data Valid
(RMII mode)
Float for MII mode.
Pull up with a resistor to VDDIO for RMII mode.
RXD3/
nINTSEL
I/O nINT pin mode select: set the mode of pin 1.
Default, left floating pin 1 is nINT, active low interrupt output.
Note: For nINT mode, tie nINT/TXD4/TXER to VDDIO with a
resistor.
Pulled to VSS by a resistor, pin 1 is TX_ER/TXD4, Transmit
Error or Transmit data 4 (5B mode).
Note: For TXD4/TXER mode, do not tie nINT/TXD4/TXER to
VDDIO or Ground.
±15kV ESD Protected MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support and flexPWR® Technology in a Small Footprint
SMSC LAN8700/LAN8700i 11 Revision 2.3 (04-12-11)
PRODUCT PREVIEW
Table 6 General Signals
SIGNAL NAME TYPE DESCRIPTION
nINT/
TX_ER/
TXD4
I/O LAN Interrupt – Active Low output. Place an external resistor
pull-up to VCC 3.3V.
Note: This signal is mux’d with TXER/TXD4
nRST I External Reset – input of the system reset. This signal is active
LOW.
CLKIN/
XTAL1
I/O Clock Input – 25 Mhz or 50 MHz external clock or crystal input.
In MII mode, this signal is the 25 MHz reference input clock
In RMII mode, this signal is the 50 MHz reference input clock
which is typically also driven to the RMII compliant Ethernet MAC
clock input.
XTAL2 O Clock Output – 25 MHz crystal output.
Note: Float this pin if using an external clock being driven
through CLKIN/XTAL1
Table 7 10/100 Line Interface
SIGNAL NAME TYPE DESCRIPTION
TXP AO Transmit Data Positive: 100Base-TX or 10Base-T differential
transmit outputs to magnetics.
TXN AO Transmit Data Negative: 100Base-TX or 10Base-T differential
transmit outputs to magnetics.
RXP AI Receive Data Positive: 100Base-TX or 10Base-T differential
receive inputs from magnetics.
RXN AI Receive Data Negative: 100Base-TX or 10Base-T differential
receive inputs from magnetics.
Table 8 Analog References
SIGNAL NAME TYPE DESCRIPTION
EXRES1 AI Connects to reference resistor of value 12.4K-Ohm, 1%
connected as described in the Analog Layout Guidelines.
Table 9 Power Signals
SIGNAL NAME TYPE DESCRIPTION
VDDIO POWER +1.6V to +3.6V Variable I/O Pad Power
VDD33 POWER +3.3V Core Regulator Input.
VDDA3.3 POWER +3.3V Analog Power
±15kV ESD Protected MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support and flexPWR® Technology in a Small Footprint
Revision 2.3 (04-12-11) 12 SMSC LAN8700/LAN8700i
PRODUCT PREVIEW
VDD_CORE POWER +1.8V (Core voltage) - 1.8V for digital circuitry on chip. Supplied
by the on-chip regulator unless configured for regulator off
mode using the RX_CLK/REGOFF pin. Place a 0.1uF capacitor
near this pin and connect the capacitor from this pin to ground.
When using the on-chip regulator, place a 4.7uF ±20%
capacitor with ESR < 1ohm near this pin and connect the
capacitor from this pin to ground. X5R or X7R ceramic
capacitors are recommended since they exhibit an ESR lower
than 0.1ohm at frequencies greater than 10kHz.
VSS POWER
Exposed Ground Flag. The flag must be connected to the
ground plane with an array of vias as described in the Analog
Layout Guidelines
Table 9 Power Signals (continued)
SIGNAL NAME TYPE DESCRIPTION
±15kV ESD Protected MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support and flexPWR® Technology in a Small Footprint
SMSC LAN8700/LAN8700i 13 Revision 2.3 (04-12-11)
PRODUCT PREVIEW
Package Outline
Figure 4 36-Pin QFN Package Outline, 6 x 6 x 0.90 mm Body (Lead-Free)
Notes:
1. Controlling Unit: millimeter.
2. Dimension b applies to plated terminals and is measured between 0.15mm and 0.30mm from the
terminal tip. Tolerance on the true position of the terminal is ± 0.05 mm at maximum material
conditions (MMC).
3. Details of terminal #1 identifier are optional but must be located within the zone indicated.
4. Coplanarity zone applies to exposed pad and terminals.
Table 10 36-Pin QFN Package Parameters
MIN NOMINAL MAX REMARKS
A 0.80 ~ 1.00 Overall Package Height
A1 0 ~ 0.05 Standoff
A2 0.60 ~ 0.80 Mold Thickness
A3 0.20 REF Copper Lead-frame Substrate
D 5.85 ~ 6.15 X Overall Size
D1 5.55 ~ 5.95 X Mold Cap Size
D2 3.55 ~ 3.85 X exposed Pad Size
E 5.85 ~ 6.15 Y Overall Size
E1 5.55 ~ 5.95 Y Mold Cap Size
E2 3.55 ~ 3.85 Y exposed Pad Size
L 0.35 ~ 0.75 Terminal Length
e 0.50 Basic Terminal Pitch
b 0.18 ~ 0.30 Terminal Width
ccc ~ ~ 0.08 Coplanarity
