PD - 94782 IRF3704ZCS IRF3704ZCL Applications l High Frequency Synchronous Buck Converters for Computer Processor Power HEXFET(R) Power MOSFET VDSS RDS(on) max 7.9m: 20V Benefits l Low RDS(on) at 4.5V VGS l Ultra-Low Gate Impedance l Fully Characterized Avalanche Voltage and Current D2Pak IRF3704ZCS Qg 8.7nC TO-262 IRF3704ZCL Absolute Maximum Ratings Max. Units VDS Drain-to-Source Voltage Parameter 20 V VGS Gate-to-Source Voltage 20 g g ID @ TC = 25C Continuous Drain Current, VGS @ 10V 67 ID @ TC = 100C Continuous Drain Current, VGS @ 10V 47 IDM Pulsed Drain Current PD @TC = 25C Maximum Power Dissipation 57 PD @TC = 100C Maximum Power Dissipation 28 TJ Linear Derating Factor Operating Junction and TSTG Storage Temperature Range c A 260 W 0.38 -55 to + 175 Soldering Temperature, for 10 seconds W/C C 300 (1.6mm from case) Thermal Resistance Parameter RJC RJA Junction-to-Case Junction-to-Ambient (PCB Mount) f Typ. Max. Units --- 2.65 C/W --- 40 Notes through are on page 11 www.irf.com 1 9/15/03 IRF3704ZCS/L Static @ TJ = 25C (unless otherwise specified) Parameter Min. Typ. Max. Units BVDSS Drain-to-Source Breakdown Voltage 20 --- --- VDSS/TJ Breakdown Voltage Temp. Coefficient --- 0.014 --- RDS(on) Static Drain-to-Source On-Resistance --- 6.3 7.9 --- 8.9 11.1 V Conditions VGS = 0V, ID = 250A V/C Reference to 25C, ID = 1mA m VGS = 10V, ID = 21A VGS = 4.5V, ID = 17A VGS(th) Gate Threshold Voltage 1.65 2.1 2.55 V VGS(th)/TJ Gate Threshold Voltage Coefficient --- -5.6 --- mV/C IDSS Drain-to-Source Leakage Current --- --- 1.0 A VDS = 16V, VGS = 0V --- --- 150 Gate-to-Source Forward Leakage --- --- 100 nA VGS = 20V Gate-to-Source Reverse Leakage --- --- -100 Forward Transconductance 48 --- --- Total Gate Charge --- 8.7 13 Qgs1 Pre-Vth Gate-to-Source Charge --- 2.9 --- Qgs2 Post-Vth Gate-to-Source Charge --- 1.1 --- Qgd Gate-to-Drain Charge --- 2.3 --- ID = 17A Qgodr Gate Charge Overdrive Switch Charge (Qgs2 + Qgd) --- 2.4 --- See Fig. 16 Qsw --- 3.4 --- IGSS gfs Qg Qoss Output Charge --- 5.6 --- td(on) Turn-On Delay Time --- 8.9 --- tr Rise Time --- 38 --- td(off) Turn-Off Delay Time --- 11 --- tf Fall Time --- 4.2 --- Ciss Input Capacitance --- 1220 --- Coss Output Capacitance --- 390 --- Crss Reverse Transfer Capacitance --- 190 --- e e VDS = VGS, ID = 250A VDS = 16V, VGS = 0V, TJ = 125C VGS = -20V S VDS = 10V, ID = 17A nC VGS = 4.5V VDS = 10V nC VDS = 10V, VGS = 0V VDD = 10V, VGS = 4.5V e ID = 17A ns Clamped Inductive Load pF VDS = 10V VGS = 0V = 1.0MHz Avalanche Characteristics EAS Parameter Single Pulse Avalanche Energy IAR Avalanche Current EAR Repetitive Avalanche Energy c d c Typ. --- Max. 36 Units mJ --- 17 A --- 5.7 mJ Diode Characteristics Parameter Min. Typ. Max. Units IS Continuous Source Current --- --- ISM (Body Diode) Pulsed Source Current --- --- VSD (Body Diode) Diode Forward Voltage --- trr Reverse Recovery Time --- Qrr Reverse Recovery Charge --- 2 c 67 g Conditions MOSFET symbol A D 260 showing the integral reverse --- 1.0 V p-n junction diode. TJ = 25C, IS = 17A, VGS = 0V 11 17 ns 2.3 3.5 nC G S e TJ = 25C, IF = 17A, VDD = 10V di/dt = 100A/s e www.irf.com IRF3704ZCS/L 1000 1000 VGS 10V 9.0V 7.0V 5.0V 4.5V 4.0V 3.5V BOTTOM 3.0V 10 ID, Drain-to-Source Current (A) ID, Drain-to-Source Current (A) 100 VGS 10V 9.0V 7.0V 5.0V 4.5V 4.0V 3.5V BOTTOM 3.0V TOP TOP 3.0V 60s PULSE WIDTH Tj = 25C 100 3.0V 10 60s PULSE WIDTH Tj = 175C 1 1 0.1 1 0.1 10 1 10 VDS, Drain-to-Source Voltage (V) VDS, Drain-to-Source Voltage (V) Fig 1. Typical Output Characteristics Fig 2. Typical Output Characteristics 2.0 RDS(on) , Drain-to-Source On Resistance (Normalized) ID, Drain-to-Source Current () 1000.0 T J = 25C T J = 175C 100.0 VDS = 10V 60s PULSE WIDTH 10.0 3.0 4.0 5.0 6.0 7.0 VGS, Gate-to-Source Voltage (V) Fig 3. Typical Transfer Characteristics www.irf.com 8.0 ID = 42A VGS = 10V 1.5 1.0 0.5 -60 -40 -20 0 20 40 60 80 100 120 140 160 180 T J , Junction Temperature (C) Fig 4. Normalized On-Resistance vs. Temperature 3 IRF3704ZCS/L 12 10000 VGS = 0V, f = 1 MHZ C iss = C gs + C gd, C ds SHORTED C rss = C gd VGS, Gate-to-Source Voltage (V) ID= 17A C, Capacitance (pF) C oss = C ds + C gd Ciss 1000 Coss Crss VDS= 16V VDS= 10V 10 8 6 4 2 0 100 1 10 0 100 5 10 15 20 25 QG Total Gate Charge (nC) VDS, Drain-to-Source Voltage (V) Fig 6. Typical Gate Charge vs. Gate-to-Source Voltage Fig 5. Typical Capacitance vs. Drain-to-Source Voltage 1000.0 1000 ID, Drain-to-Source Current (A) ISD, Reverse Drain Current (A) OPERATION IN THIS AREA LIMITED BY R DS(on) 100.0 100 T J = 175C 10.0 T J = 25C 1.0 100sec 10 VGS = 0V 1 0.1 0.0 0.5 1.0 1.5 VSD, Source-toDrain Voltage (V) Fig 7. Typical Source-Drain Diode Forward Voltage 4 2.0 1msec Tc = 25C Tj = 175C Single Pulse 0 10msec 1 10 100 VDS , Drain-toSource Voltage (V) Fig 8. Maximum Safe Operating Area www.irf.com IRF3704ZCS/L 70 2.6 VGS(th) Gate threshold Voltage (V) LIMITED BY PACKAGE ID , Drain Current (A) 60 50 40 30 20 10 0 25 50 75 100 125 150 2.2 ID = 250A 1.8 1.4 1.0 0.6 175 -75 -50 -25 T C , Case Temperature (C) 0 25 50 75 100 125 150 175 200 T J , Temperature ( C ) Fig 9. Maximum Drain Current vs. Case Temperature Fig 10. Threshold Voltage vs. Temperature Thermal Response ( Z thJC ) 10 1 D = 0.50 0.20 0.10 0.05 0.1 J 0.02 0.01 0.01 SINGLE PULSE ( THERMAL RESPONSE ) R1 R1 J 1 1 R2 R2 2 2 R3 R3 3 C 3 Ci= i/Ri Ci= i/Ri Ri (C/W) i (sec) 0.920 0.000139 0.194 0.000602 0.538 0.001567 Notes: 1. Duty Factor D = t1/t2 2. Peak Tj = P dm x Zthjc + Tc 0.001 1E-006 1E-005 0.0001 0.001 0.01 t1 , Rectangular Pulse Duration (sec) Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case www.irf.com 5 IRF3704ZCS/L 15V D.U.T RG + V - DD IAS VGS 20V A 0.01 tp Fig 12a. Unclamped Inductive Test Circuit V(BR)DSS tp EAS, Single Pulse Avalanche Energy (mJ) DRIVER L VDS 140 ID 5.6A 8.5A BOTTOM 17A TOP 120 100 80 60 40 20 0 25 50 75 100 125 150 175 Starting T J, Junction Temperature (C) Fig 12c. Maximum Avalanche Energy vs. Drain Current I AS LD VDS Fig 12b. Unclamped Inductive Waveforms + VDD D.U.T Current Regulator Same Type as D.U.T. VGS Pulse Width < 1s Duty Factor < 0.1% 50K 12V .2F .3F Fig 14a. Switching Time Test Circuit D.U.T. + V - DS VDS 90% VGS 3mA 10% IG ID Current Sampling Resistors VGS td(on) Fig 13. Gate Charge Test Circuit tr td(off) tf Fig 14b. Switching Time Waveforms 6 www.irf.com IRF3704ZCS/L D.U.T Driver Gate Drive + + P.W. - - * * * * D.U.T. ISD Waveform Reverse Recovery Current + dv/dt controlled by RG Driver same type as D.U.T. ISD controlled by Duty Factor "D" D.U.T. - Device Under Test P.W. Period * RG D= VGS=10V Circuit Layout Considerations * Low Stray Inductance * Ground Plane * Low Leakage Inductance Current Transformer Period VDD + - Body Diode Forward Current di/dt D.U.T. VDS Waveform Diode Recovery dv/dt Re-Applied Voltage Body Diode VDD Forward Drop Inductor Curent ISD Ripple 5% * VGS = 5V for Logic Level Devices Fig 15. Peak Diode Recovery dv/dt Test Circuit for N-Channel HEXFET(R) Power MOSFETs Id Vds Vgs Vgs(th) Qgs1 Qgs2 Qgd Qgodr Fig 16. Gate Charge Waveform www.irf.com 7 IRF3704ZCS/L Power MOSFET Selection for Non-Isolated DC/DC Converters Control FET Synchronous FET Special attention has been given to the power losses in the switching elements of the circuit - Q1 and Q2. Power losses in the high side switch Q1, also called the Control FET, are impacted by the Rds(on) of the MOSFET, but these conduction losses are only about one half of the total losses. The power loss equation for Q2 is approximated by; * Ploss = Pconduction + Pdrive + Poutput ( 2 Ploss = Irms x Rds(on) ) Power losses in the control switch Q1 are given by; + (Qg x Vg x f ) Ploss = Pconduction+ Pswitching+ Pdrive+ Poutput Q + oss x Vin x f + (Qrr x Vin x f ) 2 This can be expanded and approximated by; *dissipated primarily in Q1. Ploss = (Irms x Rds(on ) ) 2 Qgs 2 Qgd +Ix x Vin x f + I x x Vin x ig ig f + (Qg x Vg x f ) + Qoss x Vin x f 2 This simplified loss equation includes the terms Qgs2 and Qoss which are new to Power MOSFET data sheets. Qgs2 is a sub element of traditional gate-source charge that is included in all MOSFET data sheets. The importance of splitting this gate-source charge into two sub elements, Qgs1 and Qgs2, can be seen from Fig 16. Qgs2 indicates the charge that must be supplied by the gate driver between the time that the threshold voltage has been reached and the time the drain current rises to Idmax at which time the drain voltage begins to change. Minimizing Qgs2 is a critical factor in reducing switching losses in Q1. Qoss is the charge that must be supplied to the output capacitance of the MOSFET during every switching cycle. Figure A shows how Qoss is formed by the parallel combination of the voltage dependant (nonlinear) capacitances Cds and Cdg when multiplied by the power supply input buss voltage. For the synchronous MOSFET Q2, Rds(on) is an important characteristic; however, once again the importance of gate charge must not be overlooked since it impacts three critical areas. Under light load the MOSFET must still be turned on and off by the control IC so the gate drive losses become much more significant. Secondly, the output charge Qoss and reverse recovery charge Qrr both generate losses that are transfered to Q1 and increase the dissipation in that device. Thirdly, gate charge will impact the MOSFETs' susceptibility to Cdv/dt turn on. The drain of Q2 is connected to the switching node of the converter and therefore sees transitions between ground and Vin. As Q1 turns on and off there is a rate of change of drain voltage dV/dt which is capacitively coupled to the gate of Q2 and can induce a voltage spike on the gate that is sufficient to turn the MOSFET on, resulting in shoot-through current . The ratio of Qgd/Qgs1 must be minimized to reduce the potential for Cdv/dt turn on. Figure A: Qoss Characteristic 8 www.irf.com IRF3704ZCS/L D2Pak Package Outline Dimensions are shown in millimeters (inches) D2Pak Part Marking Information T HIS IS AN IRF530S WIT H LOT CODE 8024 AS S EMBLED ON WW 02, 2000 IN T HE AS S EMBLY LINE "L" INT ERNAT IONAL RECT IFIER LOGO PART NUMBER F530S DAT E CODE YEAR 0 = 2000 WEEK 02 LINE L AS S EMBLY LOT CODE For GB Production T HIS IS AN IRF530S WIT H LOT CODE 8024 AS S EMBLED ON WW 02, 2000 IN T HE AS S EMBLY LINE "L" INT ERNAT IONAL RECT IFIER LOGO LOT CODE www.irf.com PART NUMBER F530S DAT E CODE 9 IRF3704ZCS/L TO-262 Package Outline Dimensions are shown in millimeters (inches) IGBT 1- GATE 2- COLLECTOR TO-262 Part Marking Information EXAMPLE: THIS IS AN IRL3103L LOT CODE 1789 AS SEMBLED ON WW 19, 1997 IN T HE AS S EMBLY LINE "C" INT ERNAT IONAL RECTIFIER LOGO AS SEMBLY LOT CODE 10 PART NUMBER DAT E CODE YEAR 7 = 1997 WEEK 19 LINE C www.irf.com IRF3704ZCS/L D2Pak Tape & Reel Information TRR 1.60 (.063) 1.50 (.059) 1.60 (.063) 1.50 (.059) 4.10 (.161) 3.90 (.153) FEED DIRECTION 1.85 (.073) 11.60 (.457) 11.40 (.449) 1.65 (.065) 0.368 (.0145) 0.342 (.0135) 15.42 (.609) 15.22 (.601) 24.30 (.957) 23.90 (.941) TRL 1.75 (.069) 1.25 (.049) 10.90 (.429) 10.70 (.421) 4.72 (.136) 4.52 (.178) 16.10 (.634) 15.90 (.626) FEED DIRECTION 13.50 (.532) 12.80 (.504) 27.40 (1.079) 23.90 (.941) 4 330.00 (14.173) MAX. 60.00 (2.362) MIN. NOTES : 1. COMFORMS TO EIA-418. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION MEASURED @ HUB. 4. INCLUDES FLANGE DISTORTION @ OUTER EDGE. Notes: Repetitive rating; pulse width limited by max. junction temperature. Starting TJ = 25C, L = 0.25mH, RG = 25, IAS = 17A. Pulse width 400s; duty cycle 2%. 26.40 (1.039) 24.40 (.961) 3 30.40 (1.197) MAX. 4 This is applied to D2Pak, when mounted on 1" square PCB (FR4 or G-10 Material). For recommended footprint and soldering techniques refer to application note #AN-994. Calculated continuous current based on maximum allowable junction temperature. Package limitation current is 42A. Data and specifications subject to change without notice. This product has been designed and qualified for the Consumer market. Qualification Standards can be found on IR's Web site. IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7903 Visit us at www.irf.com for sales contact information. 09/03 www.irf.com 11 Note: For the most current drawings please refer to the IR website at: http://www.irf.com/package/