LPC4367JET256E - NXP SEMICONDUCTORS

1. General description

The LPC436x are ARM Cortex-M4 based microcontrollers for embedded applications,

which include an ARM Cortex-M0 coprocessor and an ARM Cortex-M0 subsystem for

managing peripherals, up to 1 MB of flash and 154 kB of on-chip SRAM, 16 kB of

EEPROM memory, a quad SPI Flash Interface (SPIFI), advanced configurable

peripherals such as the SCTimer/PWM and the Serial General Purpose I/O (SGPIO)

interface, two High-speed USB controllers, Ethernet, LCD, an external memory controller,

and multiple digital and analog peripherals. The LPC436x operate at CPU frequencies of

up to 204 MHz.

The ARM Cortex-M4 is a 32-bit core that offers system enhancements such as low power

consumption, enhanced debug features, and a high level of support block integration. The

ARM Cortex-M4 CPU incorporates a 3-stage pipeline, uses a Harvard architecture with

separate local instruction and data buses as well as a third bus for peripherals, and

includes an internal prefetch unit that supports speculative branching. The ARM

Cortex-M4 supports single-cycle digital signal processing and SIMD instructions. A

hardware floating-point processor is integrated into the core.

The LPC436x include an application ARM Cortex-M0 coprocessor and a second ARM

Cortex-M0 subsystem for managing the SGPIO and SPI peripherals.The ARM Cortex-M0

coprocessor is an energy-efficient and easy-to-use 32-bit core which is upward code- and

tool-compatible with the Cortex-M4 core. The Cortex-M0 coprocessor, designed as a

replacement for existing 8/16-bit microcontrollers, offers up to 204 MHz performance with

a simple instruction set and reduced code size. In LPC436x, the Cortex-M0 coprocessor

hardware multiply is implemented as a 32-cycle iterative multiplier.

For additional documentation related to the LPC43xx parts, see Section 17.

2. Features and benefits

Cortex-M4 Processor core

ARM Cortex-M4 processor (version r0p1), running at frequencies of up to

204 MHz.

Built-in Memory Protection Unit (MPU) supporting eight regions.

Built-in Nested Vectored Interrupt Controller (NVIC).

Hardware floating-point unit.

Non-maskable Interrupt (NMI) input.

JTAG and Serial Wire Debug (SWD), serial trace, eight breakpoints, and four

watch points.

Enhanced Trace Module (ETM) and Enhanced Trace Buffer (ETB) support.

LPC436x

32-bit ARM Cortex-M4/M0 MCU; up to 1 MB flash and 154 kB

SRAM; Ethernet, two High-speed USB, LCD, EMC

Rev. 1.3 — 10 January 2020 Product data sheet

Product data sheet Rev. 1.3 — 10 January 2020 2 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

System tick timer.

Cortex-M0 Processor core

ARM Cortex-M0 co-processor (version r0p0) capable of off-loading the main ARM

Cortex-M4 application processor.

Running at frequencies of up to 204 MHz.

JTAG

Built-in NVIC.

Cortex-M0 subsystem

ARM Cortex-M0 coprocessor controlling the SPI and SGPIO residing on a

separate AHB multilayer matrix. Includes 2 kB + 16 kB of SRAM.

Running at frequencies of up to 204 MHz.

Connected via a core-to-core bridge to the main AHB multilayer matrix and the

main ARM Cortex-M4 processor.

JTAG and built-in NVIC.

On-chip memory

Up to 1 MB on-chip dual bank flash memory with flash accelerator.

16 kB on-chip EEPROM data memory.

154 kB SRAM for code and data use.

Multiple SRAM blocks with separate bus access. Two SRAM blocks can be

powered down individually.

64 kB ROM containing boot code and on-chip software drivers.

64 bit+ 256 bit of One-Time Programmable (OTP) memory for general-purpose

use.

Configurable digital peripherals

Serial GPIO (SGPIO) interface.

SCTimer/PWM subsystem on AHB.

Global Input Multiplexer Array (GIMA) allows to cross-connect multiple inputs and

outputs to event driven peripherals like the timers, SCTimer/PWM, and ADC0/1.

Serial interfaces

Quad SPI Flash Interface (SPIFI) with four lanes and up to 52 MB per second.

10/100T Ethernet MAC with RMII and MII interfaces and DMA support for high

throughput at low CPU load. Support for IEEE 1588 time stamping/advanced time

stamping (IEEE 1588-2008 v2).

One High-speed USB 2.0 Host/Device/OTG interface with DMA support and

on-chip high-speed PHY.

One High-speed USB 2.0 Host/Device interface with DMA support, on-chip

full-speed PHY and ULPI interface to external high-speed PHY.

USB interface electrical test software included in ROM USB stack.

One 550 UART with DMA support and full modem interface.

Three 550 USARTs with DMA and synchronous mode support and a smart card

interface conforming to ISO7816 specification. One USART with IrDA interface.

Up to two C_CAN 2.0B controllers with one channel each.

Two SSP controllers with FIFO and multi-protocol support. Both SSPs with DMA

support.

One SPI controller.

Product data sheet Rev. 1.3 — 10 January 2020 3 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

One Fast-mode Plus I2C-bus interface with monitor mode and with open-drain I/O

pins conforming to the full I2C-bus specification. Supports data rates of up to

1 Mbit/s.

One standard I2C-bus interface with monitor mode and with standard I/O pins.

Two I2S interfaces, each with DMA support and with one input and one output.

Digital peripherals

External Memory Controller (EMC) supporting external SRAM, ROM, NOR flash,

and SDRAM devices.

LCD controller with DMA support and a programmable display resolution of up to

1024 H  768 V. Supports monochrome and color STN panels and TFT color

panels; supports 1/2/4/8 bpp Color Look-Up Table (CLUT) and 16/24-bit direct

pixel mapping. Available on parts LPC4357/53 only.

Secure Digital Input Output (SD/MMC) card interface.

Eight-channel General-Purpose DMA controller can access all memories on the

AHB and all DMA-capable AHB slaves.

Up to 164 General-Purpose Input/Output (GPIO) pins with configurable

pull-up/pull-down resistors.

GPIO registers are located on the AHB for fast access. GPIO ports have DMA

support.

Up to eight GPIO pins can be selected from all GPIO pins as edge and level

sensitive interrupt sources.

Two GPIO group interrupt modules enable an interrupt based on a programmable

pattern of input states of a group of GPIO pins.

Four general-purpose timer/counters with capture and match capabilities.

One motor control Pulse Width Modulator (PWM) for three-phase motor control.

One Quadrature Encoder Interface (QEI).

Repetitive Interrupt timer (RI timer).

Windowed watchdog timer (WWDT).

Ultra-low power Real-Time Clock (RTC) on separate power domain with 256 bytes

of battery powered backup registers.

Alarm timer; can be battery powered.

Analog peripherals

One 10-bit DAC with DMA support and a data conversion rate of 400 kSamples/s.

Two 10-bit ADCs with DMA support and a data conversion rate of 400 kSamples/s.

Up to eight input channels per ADC.

Unique ID for each device.

Clock generation unit

Crystal oscillator with an operating range of 1 MHz to 25 MHz.

12 MHz internal RC oscillator trimmed to 3 % accuracy over temperature and

voltage (1.5 % accuracy for Tamb = 0 °C to 85 °C).

Ultra-low power Real-Time Clock (RTC) crystal oscillator.

Three PLLs allow CPU operation up to the maximum CPU rate without the need for

a high-frequency crystal. The second PLL can be used with the High-speed USB,

the third PLL can be used as audio PLL.

Clock output.

Product data sheet Rev. 1.3 — 10 January 2020 4 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

Power

Single 3.3 V (2.4 V to 3.6 V) power supply with on-chip DC-to-DC converter for the

core supply and the RTC power domain.

RTC power domain can be powered separately by a 3 V battery supply.

Four reduced power modes: Sleep, Deep-sleep, Power-down, and Deep

power-down.

Processor wake-up from Sleep mode via wake-up interrupts from various

peripherals.

Wake-up from Deep-sleep, Power-down, and Deep power-down modes via

external interrupts and interrupts generated by battery powered blocks in the RTC

power domain.

Brownout detect with four separate thresholds for interrupt and forced reset.

Power-On Reset (POR).

Available as LQFP208, LBGA256, or TFBGA100 packages.

3. Applications

Industrial HMI Communication hubs

Secure IoT Gateways Embedded audio applications

Industrial automation Automotive aftermarket

Industrial control White goods

Consumer health devices

Product data sheet Rev. 1.3 — 10 January 2020 5 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

4. Ordering information

4.1 Ordering options

[1] J = -40 °C to +105 °C; F = -40 °C to +85 °C.

Table 1. Ordering information

Type number Package

Name Description Version

LPC4367JET256 LBGA256 Plastic low profile ball grid array package; 256 balls; body 17  17  1 mm SOT740-2

LPC4367JBD208 LQFP208 Plastic low profile quad flat package; 208 leads; body 28  28  1.4 mm SOT459-1

LPC4367JET100 TFBGA100 Plastic thin fine-pitch ball grid array package; 100 balls; body 9  9  0.7 mm SOT926-1

Table 2. Ordering options

Type number

Flash total

Flash bank A

Flash bank B

Total SRAM

LCD

Ethernet

USB0 (Host, Device, OTG)

USB1 (Host, Device)/

ULPI interface

PWM

QEI

ADC channels

Temperature range[1]

GPIO

LPC4367JET256 1 MB 512 kB 512 kB 154 kB yes yes yes yes/yes yes yes 8 J 164

LPC4367JBD208 1 MB 512 kB 512 kB 154 kB yes yes yes yes/yes yes yes 8 J 142

LPC4367JET100 1 MB 512 kB 512 kB 154 kB no yes yes yes/no yes yes 4 J 49

Product data sheet Rev. 1.3 — 10 January 2020 6 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

5. Block diagram

Fig 1. LPC436x Block diagram

ARM

CORTEX-M4

TEST/DEBUG

INTERFACE

I-code bus

D-code bus

system bus

GPDMA LCD SD/

MMC

ETHERNET

10/100

MAC

IEEE 1588

HIGH-SPEED

USB0

HOST/

DEVICE/OTG

HIGH-SPEED

USB1

HOST/DEVICE

EMC

HIGH-SPEED PHY

CORE-CORE

BRIDGE

SPIFI

HS GPIO

SPI

SGPIO

SCT

I2C0

I2S0

I2S1

C_CAN1

MOTOR

CONTROL

PWM

TIMER3

TIMER2

USART2

USART3

SSP1

RI TIMER

QEI

GIMA

BRIDGE 0 BRIDGE 1 BRIDGE 2 BRIDGE 3 BRIDGE

MAIN AHB MULTILAYER MATRIX

SUBSYSTEM AHB MULTILAYER MATRIX

LPC436x

10-bit ADC0

10-bit ADC1

C_CAN0

I2C1

10-bit DAC

BRIDGE

RGU

CCU2

CGU

CCU1

ALARM TIMER

CONFIGURATION

REGISTERS

OTP MEMORY

EVENT ROUTER

POWER MODE CONTROL

12 MHz IRC

RTC POWER DOMAIN

BACKUP REGISTERS

RTC OSC

RTC

aaa-018614

slaves

masters

ARM

CORTEX-M0

APPLICATION

TEST/DEBUG

INTERFACE

ARM

CORTEX-M0

SUBSYSTEM

TEST/DEBUG

INTERFACE

= connected to GPDMA

GPIO

INTERRUPTS

GPIO GROUP0

INTERRUPT

GPIO GROUP1

INTERRUPT

WWDT

USART0

UART1

SSP0

TIMER0

TIMER1

SCU

32 kB AHB SRAM

16 kB +

16 kB AHB SRAM

64 kB ROM

32 kB LOCAL SRAM

40 kB LOCAL SRAM

slaves

2 kB LOCAL SRAM

16 kB LOCAL SRAM

512 kB FLASH A

512 kB FLASH B

16 kB EEPROM

system

bus

Product data sheet Rev. 1.3 — 10 January 2020 7 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

6. Pinning information

6.1 Pinning

Fig 2. Pin configuration LBGA256 package Fig 3. Pin configuration TFBGA100 package

aaa-018950

LPC436xJET256

Transparent top view

2 4 6 8 10 12

1357911

ball A1

index area

aaa-018951

LPC436xJET100

Transparent top view

24681013579

ball A1

index area

Fig 4. Pin configuration LQFP208 package

LPC436xJBD208

104

156

105

157

208

aaa-018952

Product data sheet Rev. 1.3 — 10 January 2020 8 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

6.2 Pin description

On the LPC436x, digital pins are grouped into 16 ports, named P0 to P9 and PA to PF,

with up to 20 pins used per port. Each digital pin can support up to eight different digital

functions, including General Purpose I/O (GPIO), selectable through the System

Configuration Unit (SCU) registers. The pin name is not indicative of the GPIO port

assigned to it.

The parts contain two 10-bit ADCs (ADC0 and ADC1). The input channels of ADC0 and

ADC1 on dedicated pins and multiplexed pins are combined in such a way that all channel

0 inputs (named ADC0_0 and ADC1_0) are tied together and connected to both, channel

0 on ADC0 and channel 0 on ADC1, channel 1 inputs (named ADC0_1 and ADC1_1) are

tied together and connected to channel 1 on ADC0 and ADC1, and so forth. There are

eight ADC channels total for the two ADCs.

Product data sheet Rev. 1.3 — 10 January 2020 9 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

Table 3. Pin description

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Multiplexed digital pins

P0_0 L3 G2 47 [2] N;

I/O GPIO0[0] — General purpose digital input/output pin.

I/O SSP1_MISO — Master In Slave Out for SSP1.

IENET_RXD1 — Ethernet receive data 1 (RMII/MII interface).

I/O SGPIO0 — General purpose digital input/output pin.

-R — Function reserved.

I/O I2S0_TX_WS — Transmit Word Select. It is driven by the

master and received by the slave. Corresponds to the signal

WS in the I2S-bus specification.

I/O I2S1_TX_WS — Transmit Word Select. It is driven by the

master and received by the slave. Corresponds to the signal

WS in the I2S-bus specification.

P0_1 M2 G1 50 [2] N;

I/O GPIO0[1] — General purpose digital input/output pin.

I/O SSP1_MOSI — Master Out Slave in for SSP1.

IENET_COL — Ethernet Collision detect (MII interface).

I/O SGPIO1 — General purpose digital input/output pin.

-R — Function reserved.

ENET_TX_EN — Ethernet transmit enable (RMII/MII

interface).

I/O I2S1_TX_SDA — I2S1 transmit data. It is driven by the

transmitter and read by the receiver. Corresponds to the signal

SD in the I2S-bus specification.

P1_0 P2 H1 54 [2] N;

I/O GPIO0[4] — General purpose digital input/output pin.

ICTIN_3 — SCT input 3. Capture input 1 of timer 1.

I/O EMC_A5 — External memory address line 5.

-R — Function reserved.

I/O SSP0_SSEL — Slave Select for SSP0.

I/O SGPIO7 — General purpose digital input/output pin.

I/O EMC_D12 — External memory data line 12.

Product data sheet Rev. 1.3 — 10 January 2020 10 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P1_1 R2 K2 58 [2] N;

I/O GPIO0[8] — General purpose digital input/output pin. Boot pin

(see Table 5).

OCTOUT_7 — SCT output 7. Match output 3 of timer 1.

I/O EMC_A6 — External memory address line 6.

I/O SGPIO8 — General purpose digital input/output pin.

-R — Function reserved.

I/O SSP0_MISO — Master In Slave Out for SSP0.

-R — Function reserved.

I/O EMC_D13 — External memory data line 13.

P1_2 R3 K1 60 [2] N;

I/O GPIO0[9] — General purpose digital input/output pin. Boot pin

(see Table 5).

OCTOUT_6 — SCT output 6. Match output 2 of timer 1.

I/O EMC_A7 — External memory address line 7.

I/O SGPIO9 — General purpose digital input/output pin.

-R — Function reserved.

I/O SSP0_MOSI — Master Out Slave in for SSP0.

-R — Function reserved.

I/O EMC_D14 — External memory data line 14.

P1_3 P5 J1 61 [2] N;

I/O GPIO0[10] — General purpose digital input/output pin.

OCTOUT_8 — SCT output 8. Match output 0 of timer 2.

I/O SGPIO10 — General purpose digital input/output pin.

OEMC_OE — LOW active Output Enable signal.

OUSB0_IND1 — USB0 port indicator LED control

output 1.

I/O SSP1_MISO — Master In Slave Out for SSP1.

-R — Function reserved.

OSD_RST — SD/MMC reset signal for MMC4.4 card.

P1_4 T3 J2 64 [2] N;

I/O GPIO0[11] — General purpose digital input/output pin.

OCTOUT_9 — SCT output 9. Match output 3 of timer 3.

I/O SGPIO11 — General purpose digital input/output pin.

OEMC_BLS0 — LOW active Byte Lane select signal 0.

OUSB0_IND0 — USB0 port indicator LED control output 0.

I/O SSP1_MOSI — Master Out Slave in for SSP1.

I/O EMC_D15 — External memory data line 15.

OSD_VOLT1 — SD/MMC bus voltage select output 1.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 11 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P1_5 R5 J4 65 [2] N;

I/O GPIO1[8] — General purpose digital input/output pin.

OCTOUT_10 — SCT output 10. Match output 3 of timer 3.

-R — Function reserved.

OEMC_CS0 — LOW active Chip Select 0 signal.

IUSB0_PWR_FAULT — Port power fault signal indicating

overcurrent condition; this signal monitors over-current on the

USB bus (external circuitry required to detect over-current

condition).

I/O SSP1_SSEL — Slave Select for SSP1.

I/O SGPIO15 — General purpose digital input/output pin.

OSD_POW — SD/MMC power monitor output.

P1_6 T4 K4 67 [2] N;

I/O GPIO1[9] — General purpose digital input/output pin.

ICTIN_5 — SCT input 5. Capture input 2 of timer 2.

-R — Function reserved.

OEMC_WE — LOW active Write Enable signal.

-R — Function reserved.

OEMC_BLS0 — LOW active Byte Lane select signal 0.

I/O SGPIO14 — General purpose digital input/output pin.

I/O SD_CMD — SD/MMC command signal.

P1_7 T5 G4 69 [2] N;

I/O GPIO1[0] — General purpose digital input/output pin.

IU1_DSR — Data Set Ready input for UART1.

OCTOUT_13 — SCT output 13. Match output 3 of timer 3.

I/O EMC_D0 — External memory data line 0.

OUSB0_PPWR — VBUS drive signal (towards external charge

pump or power management unit); indicates that VBUS must

be driven (active HIGH).

Add a pull-down resistor to disable the power switch at reset.

This signal has opposite polarity compared to the USB_PPWR

used on other NXP LPC parts.

-R — Function reserved.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 12 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P1_8 R7 H5 71 [2] N;

I/O GPIO1[1] — General purpose digital input/output pin.

OU1_DTR — Data Terminal Ready output for UART1.

OCTOUT_12 — SCT output 12. Match output 3 of

timer 3.

I/O EMC_D1 — External memory data line 1.

-R — Function reserved.

OSD_VOLT0 — SD/MMC bus voltage select output 0.

P1_9 T7 J5 73 [2] N;

I/O GPIO1[2] — General purpose digital input/output pin.

OU1_RTS — Request to Send output for UART1.

OCTOUT_11 — SCT output 11. Match output 3 of timer 2.

I/O EMC_D2 — External memory data line 2.

-R — Function reserved.

I/O SD_DAT0 — SD/MMC data bus line 0.

P1_10 R8 H6 75 [2] N;

I/O GPIO1[3] — General purpose digital input/output pin.

IU1_RI — Ring Indicator input for UART1.

OCTOUT_14 — SCT output 14. Match output 2 of timer 3.

I/O EMC_D3 — External memory data line 3.

-R — Function reserved.

I/O SD_DAT1 — SD/MMC data bus line 1.

P1_11 T9 J7 77 [2] N;

I/O GPIO1[4] — General purpose digital input/output pin.

IU1_CTS — Clear to Send input for UART1.

OCTOUT_15 — SCT output 15. Match output 3 of timer 3.

I/O EMC_D4 — External memory data line 4.

-R — Function reserved.

I/O SD_DAT2 — SD/MMC data bus line 2.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 13 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P1_12 R9 K7 78 [2] N;

I/O GPIO1[5] — General purpose digital input/output pin.

IU1_DCD — Data Carrier Detect input for UART1.

-R — Function reserved.

I/O EMC_D5 — External memory data line 5.

IT0_CAP1 — Capture input 1 of timer 0.

-R — Function reserved.

I/O SGPIO8 — General purpose digital input/output pin.

I/O SD_DAT3 — SD/MMC data bus line 3.

P1_13 R10 H8 83 [2] N;

I/O GPIO1[6] — General purpose digital input/output pin.

OU1_TXD — Transmitter output for UART1.

-R — Function reserved.

I/O EMC_D6 — External memory data line 6.

IT0_CAP0 — Capture input 0 of timer 0.

-R — Function reserved.

I/O SGPIO9 — General purpose digital input/output pin.

ISD_CD — SD/MMC card detect input.

P1_14 R11 J8 85 [2] N;

I/O GPIO1[7] — General purpose digital input/output pin.

IU1_RXD — Receiver input for UART1.

-R — Function reserved.

I/O EMC_D7 — External memory data line 7.

OT0_MAT2 — Match output 2 of timer 0.

-R — Function reserved.

I/O SGPIO10 — General purpose digital input/output pin.

-R — Function reserved.

P1_15 T12 K8 87 [2] N;

I/O GPIO0[2] — General purpose digital input/output pin.

OU2_TXD — Transmitter output for USART2.

I/O SGPIO2 — General purpose digital input/output pin.

IENET_RXD0 — Ethernet receive data 0 (RMII/MII interface).

OT0_MAT1 — Match output 1 of timer 0.

-R — Function reserved.

I/O EMC_D8 — External memory data line 8.

-R — Function reserved.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 14 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P1_16 M7 H9 90 [2] N;

I/O GPIO0[3] — General purpose digital input/output pin.

IU2_RXD — Receiver input for USART2.

I/O SGPIO3 — General purpose digital input/output pin.

IENET_CRS — Ethernet Carrier Sense (MII interface).

OT0_MAT0 — Match output 0 of timer 0.

-R — Function reserved.

I/O EMC_D9 — External memory data line 9.

IENET_RX_DV — Ethernet Receive Data Valid (RMII/MII

interface).

P1_17 M8 H10 93 [3] N;

I/O GPIO0[12] — General purpose digital input/output pin.

I/O U2_UCLK — Serial clock input/output for USART2 in

synchronous mode.

-R — Function reserved.

I/O ENET_MDIO — Ethernet MIIM data input and output.

IT0_CAP3 — Capture input 3 of timer 0.

OCAN1_TD — CAN1 transmitter output.

I/O SGPIO11 — General purpose digital input/output pin.

-R — Function reserved.

P1_18 N12 J10 95 [2] N;

I/O GPIO0[13] — General purpose digital input/output pin.

I/O U2_DIR — RS-485/EIA-485 output enable/direction control for

USART2.

-R — Function reserved.

OENET_TXD0 — Ethernet transmit data 0 (RMII/MII interface).

OT0_MAT3 — Match output 3 of timer 0.

ICAN1_RD — CAN1 receiver input.

I/O SGPIO12 — General purpose digital input/output pin.

I/O EMC_D10 — External memory data line 10.

P1_19 M11 K9 96 [2] N;

IENET_TX_CLK (ENET_REF_CLK) — Ethernet Transmit

Clock (MII interface) or Ethernet Reference Clock (RMII

interface).

I/O SSP1_SCK — Serial clock for SSP1.

-R — Function reserved.

OCLKOUT — Clock output pin.

-R — Function reserved.

OI2S0_RX_MCLK — I2S receive master clock.

I/O I2S1_TX_SCK — Transmit Clock. It is driven by the master

and received by the slave. Corresponds to the signal SCK in

the I2S-bus specification.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 15 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P1_20 M10 K10 100 [2] N;

I/O GPIO0[15] — General purpose digital input/output pin.

I/O SSP1_SSEL — Slave Select for SSP1.

-R — Function reserved.

OENET_TXD1 — Ethernet transmit data 1 (RMII/MII interface).

IT0_CAP2 — Capture input 2 of timer 0.

-R — Function reserved.

I/O SGPIO13 — General purpose digital input/output pin.

I/O EMC_D11 — External memory data line 11.

P2_0 T16 G10 108 [2] N;

I/O SGPIO4 — General purpose digital input/output pin.

OU0_TXD — Transmitter output for USART0. See Table 4 for

ISP mode.

I/O EMC_A13 — External memory address line 13.

OUSB0_PPWR — VBUS drive signal (towards external charge

pump or power management unit); indicates that VBUS must

be driven (active HIGH).

Add a pull-down resistor to disable the power switch at reset.

This signal has opposite polarity compared to the USB_PPWR

used on other NXP LPC parts.

I/O GPIO5[0] — General purpose digital input/output pin.

-R — Function reserved.

IT3_CAP0 — Capture input 0 of timer 3.

OENET_MDC — Ethernet MIIM clock.

P2_1 N15 G7 116 [2] N;

I/O SGPIO5 — General purpose digital input/output pin.

IU0_RXD — Receiver input for USART0. See Table 4 for ISP

mode.

I/O EMC_A12 — External memory address line 12.

IUSB0_PWR_FAULT — Port power fault signal indicating

overcurrent condition; this signal monitors over-current on the

USB bus (external circuitry required to detect over-current

condition).

I/O GPIO5[1] — General purpose digital input/output pin.

-R — Function reserved.

IT3_CAP1 — Capture input 1 of timer 3.

-R — Function reserved.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 16 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P2_2 M15 F5 121 [2] N;

I/O SGPIO6 — General purpose digital input/output pin.

I/O U0_UCLK — Serial clock input/output for USART0 in

synchronous mode.

I/O EMC_A11 — External memory address line 11.

OUSB0_IND1 — USB0 port indicator LED control output 1.

I/O GPIO5[2] — General purpose digital input/output pin.

ICTIN_6 — SCT input 6. Capture input 1 of timer 3.

IT3_CAP2 — Capture input 2 of timer 3.

OEMC_CS1 — LOW active Chip Select 1 signal.

P2_3 J12 D8 127 [3] N;

I/O SGPIO12 — General purpose digital input/output pin.

I/O I2C1_SDA — I2C1 data input/output (this pin does not use a

specialized I2C pad).

OU3_TXD — Transmitter output for USART3. See Table 4 for

ISP mode.

ICTIN_1 — SCT input 1. Capture input 1 of timer 0. Capture

input 1 of timer 2.

I/O GPIO5[3] — General purpose digital input/output pin.

-R — Function reserved.

OT3_MAT0 — Match output 0 of timer 3.

OUSB0_PPWR — VBUS drive signal (towards external charge

pump or power management unit); indicates that VBUS must

be driven (active HIGH).

Add a pull-down resistor to disable the power switch at reset.

This signal has opposite polarity compared to the USB_PPWR

used on other NXP LPC parts.

P2_4 K11 D9 128 [3] N;

I/O SGPIO13 — General purpose digital input/output pin.

I/O I2C1_SCL — I2C1 clock input/output (this pin does not use a

specialized I2C pad).

IU3_RXD — Receiver input for USART3. See Table 4 for ISP

mode.

ICTIN_0 — SCT input 0. Capture input 0 of timer 0, 1, 2, 3.

I/O GPIO5[4] — General purpose digital input/output pin.

-R — Function reserved.

OT3_MAT1 — Match output 1 of timer 3.

IUSB0_PWR_FAULT — Port power fault signal indicating

overcurrent condition; this signal monitors over-current on the

USB bus (external circuitry required to detect over-current

condition).

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 17 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P2_5 K14 D10 131 [3] N;

I/O SGPIO14 — General purpose digital input/output pin.

ICTIN_2 — SCT input 2. Capture input 2 of timer 0.

IUSB1_VBUS — Monitors the presence of USB1 bus power.

Note: This signal must be HIGH for USB reset to occur.

IADCTRIG1 — ADC trigger input 1.

I/O GPIO5[5] — General purpose digital input/output pin.

-R — Function reserved.

OT3_MAT2 — Match output 2 of timer 3.

OUSB0_IND0 — USB0 port indicator LED control output 0.

P2_6 K16 G9 137 [2] N;

I/O SGPIO7 — General purpose digital input/output pin.

I/O U0_DIR — RS-485/EIA-485 output enable/direction control for

USART0.

I/O EMC_A10 — External memory address line 10.

OUSB0_IND0 — USB0 port indicator LED control

output 0.

I/O GPIO5[6] — General purpose digital input/output pin.

ICTIN_7 — SCT input 7.

IT3_CAP3 — Capture input 3 of timer 3.

OEMC_BLS1 — LOW active Byte Lane select signal 1.

P2_7 H14 C10 138 [2] N;

I/O GPIO0[7] — General purpose digital input/output pin. If this

pin is pulled LOW at reset, the part enters ISP mode or boots

from an external source (see Table 4 and Table 5).

OCTOUT_1 — SCT output 1. Match output 3 of timer 3.

I/O U3_UCLK — Serial clock input/output for USART3 in

synchronous mode.

I/O EMC_A9 — External memory address line 9.

-R — Function reserved.

OT3_MAT3 — Match output 3 of timer 3.

-R — Function reserved.

P2_8 J16 C6 140 [2] N;

I/O SGPIO15 — General purpose digital input/output pin. Boot pin

(see Table 5).

OCTOUT_0 — SCT output 0. Match output 0 of timer 0.

I/O U3_DIR — RS-485/EIA-485 output enable/direction control for

USART3.

I/O EMC_A8 — External memory address line 8.

I/O GPIO5[7] — General purpose digital input/output pin.

-R — Function reserved.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 18 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P2_9 H16 B10 144 [2] N;

I/O GPIO1[10] — General purpose digital input/output pin. Boot

pin (see Table 5).

OCTOUT_3 — SCT output 3. Match output 3 of timer 0.

I/O U3_BAUD — Baud pin for USART3.

I/O EMC_A0 — External memory address line 0.

-R — Function reserved.

P2_10 G16 E8 146 [2] N;

I/O GPIO0[14] — General purpose digital input/output pin.

OCTOUT_2 — SCT output 2. Match output 2 of timer 0.

OU2_TXD — Transmitter output for USART2.

I/O EMC_A1 — External memory address line 1.

-R — Function reserved.

P2_11 F16 A9 148 [2] N;

I/O GPIO1[11] — General purpose digital input/output pin.

OCTOUT_5 — SCT output 5. Match output 3 of timer 3.

IU2_RXD — Receiver input for USART2.

I/O EMC_A2 — External memory address line 2.

-R — Function reserved.

P2_12 E15 B9 153 [2] N;

I/O GPIO1[12] — General purpose digital input/output pin.

OCTOUT_4 — SCT output 4. Match output 3 of timer 3.

-R — Function reserved.

I/O EMC_A3 — External memory address line 3.

-R — Function reserved.

I/O U2_UCLK — Serial clock input/output for USART2 in

synchronous mode.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 19 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P2_13 C16 A10 156 [2] N;

I/O GPIO1[13] — General purpose digital input/output pin.

ICTIN_4 — SCT input 4. Capture input 2 of timer 1.

-R — Function reserved.

I/O EMC_A4 — External memory address line 4.

-R — Function reserved.

I/O U2_DIR — RS-485/EIA-485 output enable/direction control for

USART2.

P3_0 F13 A8 161 [2] N;

I/O I2S0_RX_SCK — I2S receive clock. It is driven by the master

and received by the slave. Corresponds to the signal SCK in

the I2S-bus specification.

OI2S0_RX_MCLK — I2S receive master clock.

I/O I2S0_TX_SCK — Transmit Clock. It is driven by the master

and received by the slave. Corresponds to the signal SCK in

the I2S-bus specification.

OI2S0_TX_MCLK — I2S transmit master clock.

I/O SSP0_SCK — Serial clock for SSP0.

-R — Function reserved.

P3_1 G11 F7 163 [2] N;

I/O I2S0_TX_WS — Transmit Word Select. It is driven by the

master and received by the slave. Corresponds to the signal

WS in the I2S-bus specification.

I/O I2S0_RX_WS — Receive Word Select. It is driven by the

master and received by the slave. Corresponds to the signal

WS in the I2S-bus specification.

ICAN0_RD — CAN receiver input.

OUSB1_IND1 — USB1 Port indicator LED control output 1.

I/O GPIO5[8] — General purpose digital input/output pin.

-R — Function reserved.

OLCD_VD15 — LCD data.

-R — Function reserved.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 20 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P3_2 F11 G6 166 [2] OL;

I/O I2S0_TX_SDA — I2S transmit data. It is driven by the

transmitter and read by the receiver. Corresponds to the signal

SD in the I2S-bus specification.

I/O I2S0_RX_SDA — I2S Receive data. It is driven by the

transmitter and read by the receiver. Corresponds to the signal

SD in the I2S-bus specification.

OCAN0_TD — CAN transmitter output.

OUSB1_IND0 — USB1 Port indicator LED control output 0.

I/O GPIO5[9] — General purpose digital input/output pin.

-R — Function reserved.

OLCD_VD14 — LCD data.

-R — Function reserved.

P3_3 B14 A7 169 [4] N;

-R — Function reserved.

I/O SPI_SCK — Serial clock for SPI.

I/O SSP0_SCK — Serial clock for SSP0.

OSPIFI_SCK — Serial clock for SPIFI.

OCGU_OUT1 — CGU spare clock output 1.

-R — Function reserved.

OI2S0_TX_MCLK — I2S transmit master clock.

I/O I2S1_TX_SCK — Transmit Clock. It is driven by the master

and received by the slave. Corresponds to the signal SCK in

the I2S-bus specification.

P3_4 A15 B8 171 [2] N;

I/O GPIO1[14] — General purpose digital input/output pin.

-R — Function reserved.

I/O SPIFI_SIO3 — I/O lane 3 for SPIFI.

OU1_TXD — Transmitter output for UART 1.

I/O I2S0_TX_WS — Transmit Word Select. It is driven by the

master and received by the slave. Corresponds to the signal

WS in the I2S-bus specification.

I/O I2S1_RX_SDA — I2S1 Receive data. It is driven by the

transmitter and read by the receiver. Corresponds to the signal

SD in the I2S-bus specification.

OLCD_VD13 — LCD data.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 21 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P3_5 C12 B7 173 [2] N;

I/O GPIO1[15] — General purpose digital input/output pin.

-R — Function reserved.

I/O SPIFI_SIO2 — I/O lane 2 for SPIFI.

IU1_RXD — Receiver input for UART 1.

I/O I2S0_TX_SDA — I2S transmit data. It is driven by the

transmitter and read by the receiver. Corresponds to the signal

SD in the I2S-bus specification.

I/O I2S1_RX_WS — Receive Word Select. It is driven by the

master and received by the slave. Corresponds to the signal

WS in the I2S-bus specification.

OLCD_VD12 — LCD data.

P3_6 B13 C7 174 [2] N;

I/O GPIO0[6] — General purpose digital input/output pin.

I/O SPI_MISO — Master In Slave Out for SPI.

I/O SSP0_SSEL — Slave Select for SSP0.

I/O SPIFI_MISO — Input 1 in SPIFI quad mode; SPIFI output IO1.

-R — Function reserved.

I/O SSP0_MISO — Master In Slave Out for SSP0.

-R — Function reserved.

P3_7 C11 D7 176 [2] N;

-R — Function reserved.

I/O SPI_MOSI — Master Out Slave In for SPI.

I/O SSP0_MISO — Master In Slave Out for SSP0.

I/O SPIFI_MOSI — Input I0 in SPIFI quad mode; SPIFI output

IO0.

I/O GPIO5[10] — General purpose digital input/output pin.

I/O SSP0_MOSI — Master Out Slave in for SSP0.

-R — Function reserved.

P3_8 C10 E7 179 [2] N;

-R — Function reserved.

ISPI_SSEL — Slave Select for SPI. Note that this pin in an

input pin only. The SPI in master mode cannot drive the CS

input on the slave. Any GPIO pin can be used for SPI chip

select in master mode.

I/O SSP0_MOSI — Master Out Slave in for SSP0.

I/O SPIFI_CS — SPIFI serial flash chip select.

I/O GPIO5[11] — General purpose digital input/output pin.

I/O SSP0_SSEL — Slave Select for SSP0.

-R — Function reserved.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 22 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P4_0 D5 - 1 [2] N;

I/O GPIO2[0] — General purpose digital input/output pin.

OMCOA0 — Motor control PWM channel 0, output A.

INMI — External interrupt input to NMI.

-R — Function reserved.

OLCD_VD13 — LCD data.

I/O U3_UCLK — Serial clock input/output for USART3 in

synchronous mode.

-R — Function reserved.

P4_1 A1 - 3 [5] N;

I/O GPIO2[1] — General purpose digital input/output pin.

OCTOUT_1 — SCT output 1. Match output 3 of timer 3.

OLCD_VD0 — LCD data.

-R — Function reserved.

OLCD_VD19 — LCD data.

OU3_TXD — Transmitter output for USART3.

IENET_COL — Ethernet Collision detect (MII interface).

AI ADC0_1 — ADC0 and ADC1, input channel 1. Configure the

pin as GPIO input and use the ADC function select register in

the SCU to select the ADC.

P4_2 D3 - 12 [2] N;

I/O GPIO2[2] — General purpose digital input/output pin.

OCTOUT_0 — SCT output 0. Match output 0 of timer 0.

OLCD_VD3 — LCD data.

-R — Function reserved.

OLCD_VD12 — LCD data.

IU3_RXD — Receiver input for USART3.

I/O SGPIO8 — General purpose digital input/output pin.

P4_3 C2 - 10 [5] N;

I/O GPIO2[3] — General purpose digital input/output pin.

OCTOUT_3 — SCT output 3. Match output 3 of timer 0.

OLCD_VD2 — LCD data.

-R — Function reserved.

OLCD_VD21 — LCD data.

I/O U3_BAUD — Baud pin for USART3.

I/O SGPIO9 — General purpose digital input/output pin.

AI ADC0_0 — DAC, ADC0 and ADC1, input channel 0.

Configure the pin as GPIO input and use the ADC function

select register in the SCU to select the ADC.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 23 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P4_4 B1 - 14 [5] N;

I/O GPIO2[4] — General purpose digital input/output pin.

OCTOUT_2 — SCT output 2. Match output 2 of timer 0.

OLCD_VD1 — LCD data.

-R — Function reserved.

OLCD_VD20 — LCD data.

I/O U3_DIR — RS-485/EIA-485 output enable/direction control for

USART3.

I/O SGPIO10 — General purpose digital input/output pin.

ODAC — DAC output. Configure the pin as GPIO input and use

the analog function select register in the SCU to select the

DAC.

P4_5 D2 - 15 [2] N;

I/O GPIO2[5] — General purpose digital input/output pin.

OCTOUT_5 — SCT output 5. Match output 3 of timer 3.

OLCD_FP — Frame pulse (STN). Vertical synchronization

pulse (TFT).

-R — Function reserved.

I/O SGPIO11 — General purpose digital input/output pin.

P4_6 C1 - 17 [2] N;

I/O GPIO2[6] — General purpose digital input/output pin.

OCTOUT_4 — SCT output 4. Match output 3 of timer 3.

OLCD_ENAB/LCDM — STN AC bias drive or TFT data enable

input.

-R — Function reserved.

I/O SGPIO12 — General purpose digital input/output pin.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 24 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P4_7 H4 - 21 [2] O;

OLCD_DCLK — LCD panel clock.

IGP_CLKIN — General purpose clock input to the CGU.

-R — Function reserved.

I/O I2S1_TX_SCK — Transmit Clock. It is driven by the master

and received by the slave. Corresponds to the signal SCK in

the I2S-bus specification.

I/O I2S0_TX_SCK — Transmit Clock. It is driven by the master

and received by the slave. Corresponds to the signal SCK in

the I2S-bus specification.

P4_8 E2 - 23 [2] N;

-R — Function reserved.

ICTIN_5 — SCT input 5. Capture input 2 of timer 2.

OLCD_VD9 — LCD data.

-R — Function reserved.

I/O GPIO5[12] — General purpose digital input/output pin.

OLCD_VD22 — LCD data.

OCAN1_TD — CAN1 transmitter output.

I/O SGPIO13 — General purpose digital input/output pin.

P4_9 L2 - 48 [2] N;

-R — Function reserved.

ICTIN_6 — SCT input 6. Capture input 1 of timer 3.

OLCD_VD11 — LCD data.

-R — Function reserved.

I/O GPIO5[13] — General purpose digital input/output pin.

OLCD_VD15 — LCD data.

ICAN1_RD — CAN1 receiver input.

I/O SGPIO14 — General purpose digital input/output pin.

P4_10 M3 - 51 [2] N;

-R — Function reserved.

ICTIN_2 — SCT input 2. Capture input 2 of timer 0.

OLCD_VD10 — LCD data.

-R — Function reserved.

I/O GPIO5[14] — General purpose digital input/output pin.

OLCD_VD14 — LCD data.

-R — Function reserved.

I/O SGPIO15 — General purpose digital input/output pin.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 25 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P5_0 N3 - 53 [2] N;

I/O GPIO2[9] — General purpose digital input/output pin.

OMCOB2 — Motor control PWM channel 2, output B.

I/O EMC_D12 — External memory data line 12.

-R — Function reserved.

IU1_DSR — Data Set Ready input for UART 1.

IT1_CAP0 — Capture input 0 of timer 1.

-R — Function reserved.

P5_1 P3 - 55 [2] N;

I/O GPIO2[10] — General purpose digital input/output pin.

IMCI2 — Motor control PWM channel 2, input.

I/O EMC_D13 — External memory data line 13.

-R — Function reserved.

OU1_DTR — Data Terminal Ready output for UART 1. Can also

be configured to be an RS-485/EIA-485 output enable signal

for UART 1.

IT1_CAP1 — Capture input 1 of timer 1.

-R — Function reserved.

P5_2 R4 - 63 [2] N;

I/O GPIO2[11] — General purpose digital input/output pin.

IMCI1 — Motor control PWM channel 1, input.

I/O EMC_D14 — External memory data line 14.

-R — Function reserved.

OU1_RTS — Request to Send output for UART 1. Can also be

configured to be an RS-485/EIA-485 output enable signal for

UART 1.

IT1_CAP2 — Capture input 2 of timer 1.

-R — Function reserved.

P5_3 T8 - 76 [2] N;

I/O GPIO2[12] — General purpose digital input/output pin.

IMCI0 — Motor control PWM channel 0, input.

I/O EMC_D15 — External memory data line 15.

-R — Function reserved.

IU1_RI — Ring Indicator input for UART 1.

IT1_CAP3 — Capture input 3 of timer 1.

-R — Function reserved.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 26 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P5_4 P9 - 80 [2] N;

I/O GPIO2[13] — General purpose digital input/output pin.

OMCOB0 — Motor control PWM channel 0, output B.

I/O EMC_D8 — External memory data line 8.

-R — Function reserved.

IU1_CTS — Clear to Send input for UART 1.

OT1_MAT0 — Match output 0 of timer 1.

-R — Function reserved.

P5_5 P10 - 81 [2] N;

I/O GPIO2[14] — General purpose digital input/output pin.

OMCOA1 — Motor control PWM channel 1, output A.

I/O EMC_D9 — External memory data line 9.

-R — Function reserved.

IU1_DCD — Data Carrier Detect input for UART 1.

OT1_MAT1 — Match output 1 of timer 1.

-R — Function reserved.

P5_6 T13 - 89 [2] N;

I/O GPIO2[15] — General purpose digital input/output pin.

OMCOB1 — Motor control PWM channel 1, output B.

I/O EMC_D10 — External memory data line 10.

-R — Function reserved.

OU1_TXD — Transmitter output for UART 1.

OT1_MAT2 — Match output 2 of timer 1.

-R — Function reserved.

P5_7 R12 - 91 [2] N;

I/O GPIO2[7] — General purpose digital input/output pin.

OMCOA2 — Motor control PWM channel 2, output A.

I/O EMC_D11 — External memory data line 11.

-R — Function reserved.

IU1_RXD — Receiver input for UART 1.

OT1_MAT3 — Match output 3 of timer 1.

-R — Function reserved.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 27 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P6_0 M12 H7 105 [2] N;

-R — Function reserved.

OI2S0_RX_MCLK — I2S receive master clock.

-R — Function reserved.

I/O I2S0_RX_SCK — Receive Clock. It is driven by the master

and received by the slave. Corresponds to the signal SCK in

the I2S-bus specification.

-R — Function reserved.

P6_1 R15 G5 107 [2] N;

I/O GPIO3[0] — General purpose digital input/output pin.

OEMC_DYCS1 — SDRAM chip select 1.

I/O U0_UCLK — Serial clock input/output for USART0 in

synchronous mode.

I/O I2S0_RX_WS — Receive Word Select. It is driven by the

master and received by the slave. Corresponds to the signal

WS in the I2S-bus specification.

-R — Function reserved.

IT2_CAP0 — Capture input 2 of timer 2.

-R — Function reserved.

P6_2 L13 J9 111 [2] N;

I/O GPIO3[1] — General purpose digital input/output pin.

OEMC_CKEOUT1 — SDRAM clock enable 1.

I/O U0_DIR — RS-485/EIA-485 output enable/direction control for

USART0.

I/O I2S0_RX_SDA — I2S Receive data. It is driven by the

transmitter and read by the receiver. Corresponds to the signal

SD in the I2S-bus specification.

-R — Function reserved.

IT2_CAP1 — Capture input 1 of timer 2.

-R — Function reserved.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 28 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P6_3 P15 - 113 [2] N;

I/O GPIO3[2] — General purpose digital input/output pin.

OUSB0_PPWR — VBUS drive signal (towards external charge

pump or power management unit); indicates that the VBUS

signal must be driven (active HIGH).

Add a pull-down resistor to disable the power switch at reset.

This signal has opposite polarity compared to the USB_PPWR

used on other NXP LPC parts.

I/O SGPIO4 — General purpose digital input/output pin.

OEMC_CS1 — LOW active Chip Select 1 signal.

-R — Function reserved.

IT2_CAP2 — Capture input 2 of timer 2.

-R — Function reserved.

P6_4 R16 F6 114 [2] N;

I/O GPIO3[3] — General purpose digital input/output pin.

ICTIN_6 — SCT input 6. Capture input 1 of timer 3.

OU0_TXD — Transmitter output for USART0.

OEMC_CAS — LOW active SDRAM Column Address Strobe.

-R — Function reserved.

P6_5 P16 F9 117 [2] N;

I/O GPIO3[4] — General purpose digital input/output pin.

OCTOUT_6 — SCT output 6. Match output 2 of timer 1.

IU0_RXD — Receiver input for USART0.

OEMC_RAS — LOW active SDRAM Row Address Strobe.

-R — Function reserved.

P6_6 L14 - 119 [2] N;

I/O GPIO0[5] — General purpose digital input/output pin.

OEMC_BLS1 — LOW active Byte Lane select signal 1.

I/O SGPIO5 — General purpose digital input/output pin.

IUSB0_PWR_FAULT — Port power fault signal indicating

overcurrent condition; this signal monitors over-current on the

USB bus (external circuitry required to detect over-current

condition).

-R — Function reserved.

IT2_CAP3 — Capture input 3 of timer 2.

-R — Function reserved.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 29 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P6_7 J13 - 123 [2] N;

-R — Function reserved.

I/O EMC_A15 — External memory address line 15.

I/O SGPIO6 — General purpose digital input/output pin.

OUSB0_IND1 — USB0 port indicator LED control output 1.

I/O GPIO5[15] — General purpose digital input/output pin.

OT2_MAT0 — Match output 0 of timer 2.

-R — Function reserved.

P6_8 H13 - 125 [2] N;

-R — Function reserved.

I/O EMC_A14 — External memory address line 14.

I/O SGPIO7 — General purpose digital input/output pin.

OUSB0_IND0 — USB0 port indicator LED control output 0.

I/O GPIO5[16] — General purpose digital input/output pin.

OT2_MAT1 — Match output 1 of timer 2.

-R — Function reserved.

P6_9 J15 F8 139 [2] N;

I/O GPIO3[5] — General purpose digital input/output pin.

-R — Function reserved.

OEMC_DYCS0 — SDRAM chip select 0.

-R — Function reserved.

OT2_MAT2 — Match output 2 of timer 2.

-R — Function reserved.

P6_10 H15 - 142 [2] N;

I/O GPIO3[6] — General purpose digital input/output pin.

OMCABORT — Motor control PWM, LOW-active fast abort.

-R — Function reserved.

OEMC_DQMOUT1 — Data mask 1 used with SDRAM and

static devices.

-R — Function reserved.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 30 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P6_11 H12 C9 143 [2] N;

I/O GPIO3[7] — General purpose digital input/output pin.

-R — Function reserved.

OEMC_CKEOUT0 — SDRAM clock enable 0.

-R — Function reserved.

OT2_MAT3 — Match output 3 of timer 2.

-R — Function reserved.

P6_12 G15 - 145 [2] N;

I/O GPIO2[8] — General purpose digital input/output pin.

OCTOUT_7 — SCT output 7. Match output 3 of timer 1.

-R — Function reserved.

OEMC_DQMOUT0 — Data mask 0 used with SDRAM and

static devices.

-R — Function reserved.

P7_0 B16 - 158 [2] N;

I/O GPIO3[8] — General purpose digital input/output pin.

OCTOUT_14 — SCT output 14. Match output 2 of timer 3.

-R — Function reserved.

OLCD_LE — Line end signal.

-R — Function reserved.

I/O SGPIO4 — General purpose digital input/output pin.

P7_1 C14 - 162 [2] N;

I/O GPIO3[9] — General purpose digital input/output pin.

OCTOUT_15 — SCT output 15. Match output 3 of timer 3.

I/O I2S0_TX_WS — Transmit Word Select. It is driven by the

master and received by the slave. Corresponds to the signal

WS in the I2S-bus specification.

OLCD_VD19 — LCD data.

OLCD_VD7 — LCD data.

-R — Function reserved.

OU2_TXD — Transmitter output for USART2.

I/O SGPIO5 — General purpose digital input/output pin.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 31 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P7_2 A16 - 165 [2] N;

I/O GPIO3[10] — General purpose digital input/output pin.

ICTIN_4 — SCT input 4. Capture input 2 of timer 1.

I/O I2S0_TX_SDA — I2S transmit data. It is driven by the

transmitter and read by the receiver. Corresponds to the signal

SD in the I2S-bus specification.

OLCD_VD18 — LCD data.

OLCD_VD6 — LCD data.

-R — Function reserved.

IU2_RXD — Receiver input for USART2.

I/O SGPIO6 — General purpose digital input/output pin.

P7_3 C13 - 167 [2] N;

I/O GPIO3[11] — General purpose digital input/output pin.

ICTIN_3 — SCT input 3. Capture input 1 of timer 1.

-R — Function reserved.

OLCD_VD17 — LCD data.

OLCD_VD5 — LCD data.

-R — Function reserved.

P7_4 C8 - 189 [5] N;

I/O GPIO3[12] — General purpose digital input/output pin.

OCTOUT_13 — SCT output 13. Match output 3 of timer 3.

-R — Function reserved.

OLCD_VD16 — LCD data.

OLCD_VD4 — LCD data.

OTRACEDATA[0] — Trace data, bit 0.

-R — Function reserved.

AI ADC0_4 — ADC0 and ADC1, input channel 4. Configure the

pin as GPIO input and use the ADC function select register in

the SCU to select the ADC.

P7_5 A7 - 191 [5] N;

I/O GPIO3[13] — General purpose digital input/output pin.

OCTOUT_12 — SCT output 12. Match output 3 of timer 3.

-R — Function reserved.

OLCD_VD8 — LCD data.

OLCD_VD23 — LCD data.

OTRACEDATA[1] — Trace data, bit 1.

-R — Function reserved.

AI ADC0_3 — ADC0 and ADC1, input channel 3. Configure the

pin as GPIO input and use the ADC function select register in

the SCU to select the ADC.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 32 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P7_6 C7 - 194 [2] N;

I/O GPIO3[14] — General purpose digital input/output pin.

OCTOUT_11 — SCT output 1. Match output 3 of timer 2.

-R — Function reserved.

OLCD_LP — Line synchronization pulse (STN). Horizontal

synchronization pulse (TFT).

-R — Function reserved.

OTRACEDATA[2] — Trace data, bit 2.

-R — Function reserved.

P7_7 B6 - 201 [5] N;

I/O GPIO3[15] — General purpose digital input/output pin.

OCTOUT_8 — SCT output 8. Match output 0 of timer 2.

-R — Function reserved.

OLCD_PWR — LCD panel power enable.

-R — Function reserved.

OTRACEDATA[3] — Trace data, bit 3.

OENET_MDC — Ethernet MIIM clock.

I/O SGPIO7 — General purpose digital input/output pin.

AI ADC1_6 — ADC1 and ADC0, input channel 6. Configure the

pin as GPIO input and use the ADC function select register in

the SCU to select the ADC.

P8_0 E5 - 2 [3] N;

I/O GPIO4[0] — General purpose digital input/output pin.

IUSB0_PWR_FAULT — Port power fault signal indicating

overcurrent condition; this signal monitors over-current on the

USB bus (external circuitry required to detect over-current

condition).

-R — Function reserved.

IMCI2 — Motor control PWM channel 2, input.

I/O SGPIO8 — General purpose digital input/output pin.

-R — Function reserved.

OT0_MAT0 — Match output 0 of timer 0.

P8_1 H5 - 34 [3] N;

I/O GPIO4[1] — General purpose digital input/output pin.

OUSB0_IND1 — USB0 port indicator LED control output 1.

-R — Function reserved.

IMCI1 — Motor control PWM channel 1, input.

I/O SGPIO9 — General purpose digital input/output pin.

-R — Function reserved.

OT0_MAT1 — Match output 1 of timer 0.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 33 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P8_2 K4 - 36 [3] N;

I/O GPIO4[2] — General purpose digital input/output pin.

OUSB0_IND0 — USB0 port indicator LED control output 0.

-R — Function reserved.

IMCI0 — Motor control PWM channel 0, input.

I/O SGPIO10 — General purpose digital input/output pin.

-R — Function reserved.

OT0_MAT2 — Match output 2 of timer 0.

P8_3 J3 - 37 [2] N;

I/O GPIO4[3] — General purpose digital input/output pin.

I/O USB1_ULPI_D2 — ULPI link bidirectional data line 2.

-R — Function reserved.

OLCD_VD12 — LCD data.

OLCD_VD19 — LCD data.

-R — Function reserved.

OT0_MAT3 — Match output 3 of timer 0.

P8_4 J2 - 39 [2] N;

I/O GPIO4[4] — General purpose digital input/output pin.

I/O USB1_ULPI_D1 — ULPI link bidirectional data line 1.

-R — Function reserved.

OLCD_VD7 — LCD data.

OLCD_VD16 — LCD data.

-R — Function reserved.

IT0_CAP0 — Capture input 0 of timer 0.

P8_5 J1 - 40 [2] N;

I/O GPIO4[5] — General purpose digital input/output pin.

I/O USB1_ULPI_D0 — ULPI link bidirectional data line 0.

-R — Function reserved.

OLCD_VD6 — LCD data.

OLCD_VD8 — LCD data.

-R — Function reserved.

IT0_CAP1 — Capture input 1 of timer 0.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 34 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P8_6 K3 - 43 [2] N;

I/O GPIO4[6] — General purpose digital input/output pin.

IUSB1_ULPI_NXT — ULPI link NXT signal. Data flow control

signal from the PHY.

-R — Function reserved.

OLCD_VD5 — LCD data.

OLCD_LP — Line synchronization pulse (STN). Horizontal

synchronization pulse (TFT).

-R — Function reserved.

IT0_CAP2 — Capture input 2 of timer 0.

P8_7 K1 - 45 [2] N;

I/O GPIO4[7] — General purpose digital input/output pin.

OUSB1_ULPI_STP — ULPI link STP signal. Asserted to end or

interrupt transfers to the PHY.

-R — Function reserved.

OLCD_VD4 — LCD data.

OLCD_PWR — LCD panel power enable.

-R — Function reserved.

IT0_CAP3 — Capture input 3 of timer 0.

P8_8 L1 - 49 [2] N;

-R — Function reserved.

IUSB1_ULPI_CLK — ULPI link CLK signal. 60 MHz clock

generated by the PHY.

-R — Function reserved.

OCGU_OUT0 — CGU spare clock output 0.

OI2S1_TX_MCLK — I2S1 transmit master clock.

P9_0 T1 - 59 [2] N;

I/O GPIO4[12] — General purpose digital input/output pin.

OMCABORT — Motor control PWM, LOW-active fast abort.

-R — Function reserved.

IENET_CRS — Ethernet Carrier Sense (MII interface).

I/O SGPIO0 — General purpose digital input/output pin.

I/O SSP0_SSEL — Slave Select for SSP0.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 35 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P9_1 N6 - 66 [2] N;

I/O GPIO4[13] — General purpose digital input/output pin.

OMCOA2 — Motor control PWM channel 2, output A.

-R — Function reserved.

I/O I2S0_TX_WS — Transmit Word Select. It is driven by the

master and received by the slave. Corresponds to the signal

WS in the I2S-bus specification.

IENET_RX_ER — Ethernet receive error (MII interface).

I/O SGPIO1 — General purpose digital input/output pin.

I/O SSP0_MISO — Master In Slave Out for SSP0.

P9_2 N8 - 70 [2] N;

I/O GPIO4[14] — General purpose digital input/output pin.

OMCOB2 — Motor control PWM channel 2, output B.

-R — Function reserved.

I/O I2S0_TX_SDA — I2S transmit data. It is driven by the

transmitter and read by the receiver. Corresponds to the signal

SD in the I2S-bus specification.

IENET_RXD3 — Ethernet receive data 3 (MII interface).

I/O SGPIO2 — General purpose digital input/output pin.

I/O SSP0_MOSI — Master Out Slave in for SSP0.

P9_3 M6 - 79 [2] N;

I/O GPIO4[15] — General purpose digital input/output pin.

OMCOA0 — Motor control PWM channel 0, output A.

OUSB1_IND1 — USB1 Port indicator LED control output 1.

-R — Function reserved.

IENET_RXD2 — Ethernet receive data 2 (MII interface).

I/O SGPIO9 — General purpose digital input/output pin.

OU3_TXD — Transmitter output for USART3.

P9_4 N10 - 92 [2] N;

-R — Function reserved.

OMCOB0 — Motor control PWM channel 0, output B.

OUSB1_IND0 — USB1 Port indicator LED control output 0.

-R — Function reserved.

I/O GPIO5[17] — General purpose digital input/output pin.

OENET_TXD2 — Ethernet transmit data 2 (MII interface).

I/O SGPIO4 — General purpose digital input/output pin.

IU3_RXD — Receiver input for USART3.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 36 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

P9_5 M9 - 98 [2] N;

-R — Function reserved.

OMCOA1 — Motor control PWM channel 1, output A.

OUSB1_PPWR — VBUS drive signal (towards external charge

pump or power management unit); indicates that VBUS must

be driven (active high).

Add a pull-down resistor to disable the power switch at reset.

This signal has opposite polarity compared to the USB_PPWR

used on other NXP LPC parts.

-R — Function reserved.

I/O GPIO5[18] — General purpose digital input/output pin.

OENET_TXD3 — Ethernet transmit data 3 (MII interface).

I/O SGPIO3 — General purpose digital input/output pin.

OU0_TXD — Transmitter output for USART0.

P9_6 L11 - 103 [2] N;

I/O GPIO4[11] — General purpose digital input/output pin.

OMCOB1 — Motor control PWM channel 1, output B.

IUSB1_PWR_FAULT — USB1 Port power fault signal

indicating over-current condition; this signal monitors

over-current on the USB1 bus (external circuitry required to

detect over-current condition).

-R — Function reserved.

IENET_COL — Ethernet Collision detect (MII interface).

I/O SGPIO8 — General purpose digital input/output pin.

IU0_RXD — Receiver input for USART0.

PA_0 L12 - 126 [2] N;

-R — Function reserved.

OI2S1_RX_MCLK — I2S1 receive master clock.

OCGU_OUT1 — CGU spare clock output 1.

-R — Function reserved.

PA_1 J14 - 134 [3] N;

I/O GPIO4[8] — General purpose digital input/output pin.

IQEI_IDX — Quadrature Encoder Interface INDEX input.

-R — Function reserved.

OU2_TXD — Transmitter output for USART2.

-R — Function reserved.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 37 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

PA_2 K15 - 136 [3] N;

I/O GPIO4[9] — General purpose digital input/output pin.

IQEI_PHB — Quadrature Encoder Interface PHB input.

-R — Function reserved.

IU2_RXD — Receiver input for USART2.

-R — Function reserved.

PA_3 H11 - 147 [3] N;

I/O GPIO4[10] — General purpose digital input/output pin.

IQEI_PHA — Quadrature Encoder Interface PHA input.

-R — Function reserved.

PA_4 G13 - 151 [2] N;

-R — Function reserved.

OCTOUT_9 — SCT output 9. Match output 3 of timer 3.

-R — Function reserved.

I/O EMC_A23 — External memory address line 23.

I/O GPIO5[19] — General purpose digital input/output pin.

-R — Function reserved.

PB_0 B15 - 164 [2] N;

-R — Function reserved.

OCTOUT_10 — SCT output 10. Match output 3 of timer 3.

OLCD_VD23 — LCD data.

-R — Function reserved.

I/O GPIO5[20] — General purpose digital input/output pin.

-R — Function reserved.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 38 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

PB_1 A14 - 175 [2] N;

-R — Function reserved.

IUSB1_ULPI_DIR — ULPI link DIR signal. Controls the ULP

data line direction.

OLCD_VD22 — LCD data.

-R — Function reserved.

I/O GPIO5[21] — General purpose digital input/output pin.

OCTOUT_6 — SCT output 6. Match output 2 of timer 1.

-R — Function reserved.

PB_2 B12 - 177 [2] N;

-R — Function reserved.

I/O USB1_ULPI_D7 — ULPI link bidirectional data line 7.

OLCD_VD21 — LCD data.

-R — Function reserved.

I/O GPIO5[22] — General purpose digital input/output pin.

OCTOUT_7 — SCT output 7. Match output 3 of timer 1.

-R — Function reserved.

PB_3 A13 - 178 [2] N;

-R — Function reserved.

I/O USB1_ULPI_D6 — ULPI link bidirectional data line 6.

OLCD_VD20 — LCD data.

-R — Function reserved.

I/O GPIO5[23] — General purpose digital input/output pin.

OCTOUT_8 — SCT output 8. Match output 0 of timer 2.

-R — Function reserved.

PB_4 B11 - 180 [2] N;

-R — Function reserved.

I/O USB1_ULPI_D5 — ULPI link bidirectional data line 5.

OLCD_VD15 — LCD data.

-R — Function reserved.

I/O GPIO5[24] — General purpose digital input/output pin.

ICTIN_5 — SCT input 5. Capture input 2 of timer 2.

-R — Function reserved.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 39 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

PB_5 A12 - 181 [2] N;

-R — Function reserved.

I/O USB1_ULPI_D4 — ULPI link bidirectional data line 4.

OLCD_VD14 — LCD data.

-R — Function reserved.

I/O GPIO5[25] — General purpose digital input/output pin.

ICTIN_7 — SCT input 7.

OLCD_PWR — LCD panel power enable.

-R — Function reserved.

PB_6 A6 - - [5] N;

-R — Function reserved.

I/O USB1_ULPI_D3 — ULPI link bidirectional data line 3.

OLCD_VD13 — LCD data.

-R — Function reserved.

I/O GPIO5[26] — General purpose digital input/output pin.

ICTIN_6 — SCT input 6. Capture input 1 of timer 3.

OLCD_VD19 — LCD data.

-R — Function reserved.

AI ADC0_6 — ADC0 and ADC1, input channel 6. Configure the

pin as GPIO input and use the ADC function select register in

the SCU to select the ADC.

PC_0 D4 - 7 [5] N;

-R — Function reserved.

IUSB1_ULPI_CLK — ULPI link CLK signal. 60 MHz clock

generated by the PHY.

-R — Function reserved.

I/O ENET_RX_CLK — Ethernet Receive Clock (MII interface).

OLCD_DCLK — LCD panel clock.

-R — Function reserved.

I/O SD_CLK — SD/MMC card clock.

AI ADC1_1 — ADC1 and ADC0, input channel 1. Configure the

pin as input (USB_ULPI_CLK) and use the ADC function

select register in the SCU to select the ADC.

PC_1 E4 - 9 [2] N;

I/O USB1_ULPI_D7 — ULPI link bidirectional data line 7.

-R — Function reserved.

IU1_RI — Ring Indicator input for UART 1.

OENET_MDC — Ethernet MIIM clock.

I/O GPIO6[0] — General purpose digital input/output pin.

-R — Function reserved.

IT3_CAP0 — Capture input 0 of timer 3.

OSD_VOLT0 — SD/MMC bus voltage select output 0.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 40 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

PC_2 F6 - 13 [2] N;

I/O USB1_ULPI_D6 — ULPI link bidirectional data line 6.

-R — Function reserved.

IU1_CTS — Clear to Send input for UART 1.

OENET_TXD2 — Ethernet transmit data 2 (MII interface).

I/O GPIO6[1] — General purpose digital input/output pin.

-R — Function reserved.

OSD_RST — SD/MMC reset signal for MMC4.4 card.

PC_3 F5 - 11 [5] N;

I/O USB1_ULPI_D5 — ULPI link bidirectional data line 5.

-R — Function reserved.

OU1_RTS — Request to Send output for UART 1. Can also be

configured to be an RS-485/EIA-485 output enable signal for

UART 1.

OENET_TXD3 — Ethernet transmit data 3 (MII interface).

I/O GPIO6[2] — General purpose digital input/output pin.

-R — Function reserved.

OSD_VOLT1 — SD/MMC bus voltage select output 1.

AI ADC1_0 — DAC, ADC1 and ADC0, input channel 0.

Configure the pin as GPIO input and use the ADC function

select register in the SCU to select the ADC.

PC_4 F4 - 16 [2] N;

-R — Function reserved.

I/O USB1_ULPI_D4 — ULPI link bidirectional data line 4.

-R — Function reserved.

ENET_TX_EN — Ethernet transmit enable (RMII/MII

interface).

I/O GPIO6[3] — General purpose digital input/output pin.

-R — Function reserved.

IT3_CAP1 — Capture input 1 of timer 3.

I/O SD_DAT0 — SD/MMC data bus line 0.

PC_5 G4 - 20 [2] N;

-R — Function reserved.

I/O USB1_ULPI_D3 — ULPI link bidirectional data line 3.

-R — Function reserved.

OENET_TX_ER — Ethernet Transmit Error (MII interface).

I/O GPIO6[4] — General purpose digital input/output pin.

-R — Function reserved.

IT3_CAP2 — Capture input 2 of timer 3.

I/O SD_DAT1 — SD/MMC data bus line 1.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 41 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

PC_6 H6 - 22 [2] N;

-R — Function reserved.

I/O USB1_ULPI_D2 — ULPI link bidirectional data line 2.

-R — Function reserved.

IENET_RXD2 — Ethernet receive data 2 (MII interface).

I/O GPIO6[5] — General purpose digital input/output pin.

-R — Function reserved.

IT3_CAP3 — Capture input 3 of timer 3.

I/O SD_DAT2 — SD/MMC data bus line 2.

PC_7 G5 - - [2] N;

-R — Function reserved.

I/O USB1_ULPI_D1 — ULPI link bidirectional data line 1.

-R — Function reserved.

IENET_RXD3 — Ethernet receive data 3 (MII interface).

I/O GPIO6[6] — General purpose digital input/output pin.

-R — Function reserved.

OT3_MAT0 — Match output 0 of timer 3.

I/O SD_DAT3 — SD/MMC data bus line 3.

PC_8 N4 - - [2] N;

-R — Function reserved.

I/O USB1_ULPI_D0 — ULPI link bidirectional data line 0.

-R — Function reserved.

IENET_RX_DV — Ethernet Receive Data Valid (RMII/MII

interface).

I/O GPIO6[7] — General purpose digital input/output pin.

-R — Function reserved.

OT3_MAT1 — Match output 1 of timer 3.

ISD_CD — SD/MMC card detect input.

PC_9 K2 - - [2] N;

-R — Function reserved.

IUSB1_ULPI_NXT — ULPI link NXT signal. Data flow control

signal from the PHY.

-R — Function reserved.

IENET_RX_ER — Ethernet receive error (MII interface).

I/O GPIO6[8] — General purpose digital input/output pin.

-R — Function reserved.

OT3_MAT2 — Match output 2 of timer 3.

OSD_POW — SD/MMC power monitor output.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 42 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

PC_10 M5 - - [2] N;

-R — Function reserved.

OUSB1_ULPI_STP — ULPI link STP signal. Asserted to end or

interrupt transfers to the PHY.

IU1_DSR — Data Set Ready input for UART 1.

-R — Function reserved.

I/O GPIO6[9] — General purpose digital input/output pin.

-R — Function reserved.

OT3_MAT3 — Match output 3 of timer 3.

I/O SD_CMD — SD/MMC command signal.

PC_11 L5 - - [2] N;

-R — Function reserved.

IUSB1_ULPI_DIR — ULPI link DIR signal. Controls the ULPI

data line direction.

IU1_DCD — Data Carrier Detect input for UART 1.

-R — Function reserved.

I/O GPIO6[10] — General purpose digital input/output pin.

-R — Function reserved.

I/O SD_DAT4 — SD/MMC data bus line 4.

PC_12 L6 - - [2] N;

-R — Function reserved.

OU1_DTR — Data Terminal Ready output for UART 1. Can also

be configured to be an RS-485/EIA-485 output enable signal

for UART 1.

-R — Function reserved.

I/O GPIO6[11] — General purpose digital input/output pin.

I/O SGPIO11 — General purpose digital input/output pin.

I/O I2S0_TX_SDA — I2S transmit data. It is driven by the

transmitter and read by the receiver. Corresponds to the signal

SD in the I2S-bus specification.

I/O SD_DAT5 — SD/MMC data bus line 5.

PC_13 M1 - - [2] N;

-R — Function reserved.

OU1_TXD — Transmitter output for UART 1.

-R — Function reserved.

I/O GPIO6[12] — General purpose digital input/output pin.

I/O SGPIO12 — General purpose digital input/output pin.

I/O I2S0_TX_WS — Transmit Word Select. It is driven by the

master and received by the slave. Corresponds to the signal

WS in the I2S-bus specification.

I/O SD_DAT6 — SD/MMC data bus line 6.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 43 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

PC_14 N1 - - [2] N;

-R — Function reserved.

IU1_RXD — Receiver input for UART 1.

-R — Function reserved.

I/O GPIO6[13] — General purpose digital input/output pin.

I/O SGPIO13 — General purpose digital input/output pin.

OENET_TX_ER — Ethernet Transmit Error (MII interface).

I/O SD_DAT7 — SD/MMC data bus line 7.

PD_0 N2 - - [2] N;

-R — Function reserved.

OCTOUT_15 — SCT output 15. Match output 3 of timer 3.

OEMC_DQMOUT2 — Data mask 2 used with SDRAM and

static devices.

-R — Function reserved.

I/O GPIO6[14] — General purpose digital input/output pin.

-R — Function reserved.

I/O SGPIO4 — General purpose digital input/output pin.

PD_1 P1 - - [2] N;

-R — Function reserved.

OEMC_CKEOUT2 — SDRAM clock enable 2.

-R — Function reserved.

I/O GPIO6[15] — General purpose digital input/output pin.

OSD_POW — SD/MMC power monitor output.

-R — Function reserved.

I/O SGPIO5 — General purpose digital input/output pin.

PD_2 R1 - - [2] N;

-R — Function reserved.

OCTOUT_7 — SCT output 7. Match output 3 of timer 1.

I/O EMC_D16 — External memory data line 16.

-R — Function reserved.

I/O GPIO6[16] — General purpose digital input/output pin.

-R — Function reserved.

I/O SGPIO6 — General purpose digital input/output pin.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 44 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

PD_3 P4 - - [2] N;

-R — Function reserved.

OCTOUT_6 — SCT output 7. Match output 2 of timer 1.

I/O EMC_D17 — External memory data line 17.

-R — Function reserved.

I/O GPIO6[17] — General purpose digital input/output pin.

-R — Function reserved.

I/O SGPIO7 — General purpose digital input/output pin.

PD_4 T2 - - [2] N;

-R — Function reserved.

OCTOUT_8 — SCT output 8. Match output 0 of timer 2.

I/O EMC_D18 — External memory data line 18.

-R — Function reserved.

I/O GPIO6[18] — General purpose digital input/output pin.

-R — Function reserved.

I/O SGPIO8 — General purpose digital input/output pin.

PD_5 P6 - - [2] N;

-R — Function reserved.

OCTOUT_9 — SCT output 9. Match output 3 of timer 3.

I/O EMC_D19 — External memory data line 19.

-R — Function reserved.

I/O GPIO6[19] — General purpose digital input/output pin.

-R — Function reserved.

I/O SGPIO9 — General purpose digital input/output pin.

PD_6 R6 - 68 [2] N;

-R — Function reserved.

OCTOUT_10 — SCT output 10. Match output 3 of timer 3.

I/O EMC_D20 — External memory data line 20.

-R — Function reserved.

I/O GPIO6[20] — General purpose digital input/output pin.

-R — Function reserved.

I/O SGPIO10 — General purpose digital input/output pin.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 45 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

PD_7 T6 - 72 [2] N;

-R — Function reserved.

ICTIN_5 — SCT input 5. Capture input 2 of timer 2.

I/O EMC_D21 — External memory data line 21.

-R — Function reserved.

I/O GPIO6[21] — General purpose digital input/output pin.

-R — Function reserved.

I/O SGPIO11 — General purpose digital input/output pin.

PD_8 P8 - 74 [2] N;

-R — Function reserved.

ICTIN_6 — SCT input 6. Capture input 1 of timer 3.

I/O EMC_D22 — External memory data line 22.

-R — Function reserved.

I/O GPIO6[22] — General purpose digital input/output pin.

-R — Function reserved.

I/O SGPIO12 — General purpose digital input/output pin.

PD_9 T11 - 84 [2] N;

-R — Function reserved.

OCTOUT_13 — SCT output 13. Match output 3 of timer 3.

I/O EMC_D23 — External memory data line 23.

-R — Function reserved.

I/O GPIO6[23] — General purpose digital input/output pin.

-R — Function reserved.

I/O SGPIO13 — General purpose digital input/output pin.

PD_10 P11 - 86 [2] N;

-R — Function reserved.

ICTIN_1 — SCT input 1. Capture input 1 of timer 0. Capture

input 1 of timer 2.

OEMC_BLS3 — LOW active Byte Lane select signal 3.

-R — Function reserved.

I/O GPIO6[24] — General purpose digital input/output pin.

-R — Function reserved.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 46 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

PD_11 N9 - 88 [2] N;

-R — Function reserved.

OEMC_CS3 — LOW active Chip Select 3 signal.

-R — Function reserved.

I/O GPIO6[25] — General purpose digital input/output pin.

I/O USB1_ULPI_D0 — ULPI link bidirectional data line 0.

OCTOUT_14 — SCT output 14. Match output 2 of timer 3.

-R — Function reserved.

PD_12 N11 - 94 [2] N;

-R — Function reserved.

OEMC_CS2 — LOW active Chip Select 2 signal.

-R — Function reserved.

I/O GPIO6[26] — General purpose digital input/output pin.

-R — Function reserved.

OCTOUT_10 — SCT output 10. Match output 3 of timer 3.

-R — Function reserved.

PD_13 T14 - 97 [2] N;

-R — Function reserved.

ICTIN_0 — SCT input 0. Capture input 0 of timer 0, 1, 2, 3.

OEMC_BLS2 — LOW active Byte Lane select signal 2.

-R — Function reserved.

I/O GPIO6[27] — General purpose digital input/output pin.

-R — Function reserved.

OCTOUT_13 — SCT output 13. Match output 3 of timer 3.

-R — Function reserved.

PD_14 R13 - 99 [2] N;

-R — Function reserved.

OEMC_DYCS2 — SDRAM chip select 2.

-R — Function reserved.

I/O GPIO6[28] — General purpose digital input/output pin.

-R — Function reserved.

OCTOUT_11 — SCT output 11. Match output 3 of timer 2.

-R — Function reserved.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 47 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

PD_15 T15 - 101 [2] N;

-R — Function reserved.

I/O EMC_A17 — External memory address line 17.

-R — Function reserved.

I/O GPIO6[29] — General purpose digital input/output pin.

ISD_WP — SD/MMC card write protect input.

OCTOUT_8 — SCT output 8. Match output 0 of timer 2.

-R — Function reserved.

PD_16 R14 - 104 [2] N;

-R — Function reserved.

I/O EMC_A16 — External memory address line 16.

-R — Function reserved.

I/O GPIO6[30] — General purpose digital input/output pin.

OSD_VOLT2 — SD/MMC bus voltage select output 2.

OCTOUT_12 — SCT output 12. Match output 3 of timer 3.

-R — Function reserved.

PE_0 P14 - 106 [2] N;

-R — Function reserved.

I/O EMC_A18 — External memory address line 18.

I/O GPIO7[0] — General purpose digital input/output pin.

OCAN1_TD — CAN1 transmitter output.

-R — Function reserved.

PE_1 N14 - 112 [2] N;

-R — Function reserved.

I/O EMC_A19 — External memory address line 19.

I/O GPIO7[1] — General purpose digital input/output pin.

ICAN1_RD — CAN1 receiver input.

-R — Function reserved.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 48 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

PE_2 M14 - 115 [2] N;

IADCTRIG0 — ADC trigger input 0.

ICAN0_RD — CAN receiver input.

-R — Function reserved.

I/O EMC_A20 — External memory address line 20.

I/O GPIO7[2] — General purpose digital input/output pin.

-R — Function reserved.

PE_3 K12 - 118 [2] N;

-R — Function reserved.

OCAN0_TD — CAN transmitter output.

IADCTRIG1 — ADC trigger input 1.

I/O EMC_A21 — External memory address line 21.

I/O GPIO7[3] — General purpose digital input/output pin.

-R — Function reserved.

PE_4 K13 - 120 [2] N;

-R — Function reserved.

INMI — External interrupt input to NMI.

-R — Function reserved.

I/O EMC_A22 — External memory address line 22.

I/O GPIO7[4] — General purpose digital input/output pin.

-R — Function reserved.

PE_5 N16 - 122 [2] N;

-R — Function reserved.

OCTOUT_3 — SCT output 3. Match output 3 of timer 0.

OU1_RTS — Request to Send output for UART 1. Can also be

configured to be an RS-485/EIA-485 output enable signal for

UART 1.

I/O EMC_D24 — External memory data line 24.

I/O GPIO7[5] — General purpose digital input/output pin.

-R — Function reserved.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 49 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

PE_6 M16 - 124 [2] N;

-R — Function reserved.

OCTOUT_2 — SCT output 2. Match output 2 of timer 0.

IU1_RI — Ring Indicator input for UART 1.

I/O EMC_D25 — External memory data line 25.

I/O GPIO7[6] — General purpose digital input/output pin.

-R — Function reserved.

PE_7 F15 - 149 [2] N;

-R — Function reserved.

OCTOUT_5 — SCT output 5. Match output 3 of timer 3.

IU1_CTS — Clear to Send input for UART1.

I/O EMC_D26 — External memory data line 26.

I/O GPIO7[7] — General purpose digital input/output pin.

-R — Function reserved.

PE_8 F14 - 150 [2] N;

-R — Function reserved.

OCTOUT_4 — SCT output 4. Match output 3 of timer 3.

IU1_DSR — Data Set Ready input for UART 1.

I/O EMC_D27 — External memory data line 27.

I/O GPIO7[8] — General purpose digital input/output pin.

-R — Function reserved.

PE_9 E16 - 152 [2] N;

-R — Function reserved.

ICTIN_4 — SCT input 4. Capture input 2 of timer 1.

IU1_DCD — Data Carrier Detect input for UART 1.

I/O EMC_D28 — External memory data line 28.

I/O GPIO7[9] — General purpose digital input/output pin.

-R — Function reserved.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 50 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

PE_10 E14 - 154 [2] N;

-R — Function reserved.

ICTIN_3 — SCT input 3. Capture input 1 of timer 1.

OU1_DTR — Data Terminal Ready output for UART 1. Can also

be configured to be an RS-485/EIA-485 output enable signal

for UART 1.

I/O EMC_D29 — External memory data line 29.

I/O GPIO7[10] — General purpose digital input/output pin.

-R — Function reserved.

PE_11 D16 - - [2] N;

-R — Function reserved.

OCTOUT_12 — SCT output 12. Match output 3 of timer 3.

OU1_TXD — Transmitter output for UART 1.

I/O EMC_D30 — External memory data line 30.

I/O GPIO7[11] — General purpose digital input/output pin.

-R — Function reserved.

PE_12 D15 - - [2] N;

-R — Function reserved.

OCTOUT_11 — SCT output 11. Match output 3 of

timer 2.

IU1_RXD — Receiver input for UART 1.

I/O EMC_D31 — External memory data line 31.

I/O GPIO7[12] — General purpose digital input/output pin.

-R — Function reserved.

PE_13 G14 - - [2] N;

-R — Function reserved.

OCTOUT_14 — SCT output 14. Match output 2 of timer 3.

I/O I2C1_SDA — I2C1 data input/output (this pin does not use a

specialized I2C pad).

OEMC_DQMOUT3 — Data mask 3 used with SDRAM and

static devices.

I/O GPIO7[13] — General purpose digital input/output pin.

-R — Function reserved.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 51 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

PE_14 C15 - - [2] N;

-R — Function reserved.

OEMC_DYCS3 — SDRAM chip select 3.

I/O GPIO7[14] — General purpose digital input/output pin.

-R — Function reserved.

PE_15 E13 - - [2] N;

-R — Function reserved.

OCTOUT_0 — SCT output 0. Match output 0 of timer 0.

I/O I2C1_SCL — I2C1 clock input/output (this pin does not use a

specialized I2C pad).

OEMC_CKEOUT3 — SDRAM clock enable 3.

I/O GPIO7[15] — General purpose digital input/output pin.

-R — Function reserved.

PF_0 D12 - 159 [2] O;

I/O SSP0_SCK — Serial clock for SSP0.

IGP_CLKIN — General purpose clock input to the CGU.

-R — Function reserved.

OI2S1_TX_MCLK — I2S1 transmit master clock.

PF_1 E11 - - [2] N;

-R — Function reserved.

I/O SSP0_SSEL — Slave Select for SSP0.

-R — Function reserved.

I/O GPIO7[16] — General purpose digital input/output pin.

-R — Function reserved.

I/O SGPIO0 — General purpose digital input/output pin.

-R — Function reserved.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 52 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

PF_2 D11 - 168 [2] N;

-R — Function reserved.

OU3_TXD — Transmitter output for USART3.

I/O SSP0_MISO — Master In Slave Out for SSP0.

-R — Function reserved.

I/O GPIO7[17] — General purpose digital input/output pin.

-R — Function reserved.

I/O SGPIO1 — General purpose digital input/output pin.

-R — Function reserved.

PF_3 E10 - 170 [2] N;

-R — Function reserved.

IU3_RXD — Receiver input for USART3.

I/O SSP0_MOSI — Master Out Slave in for SSP0.

-R — Function reserved.

I/O GPIO7[18] — General purpose digital input/output pin.

-R — Function reserved.

I/O SGPIO2 — General purpose digital input/output pin.

-R — Function reserved.

PF_4 D10 H4 172 [2] O;

I/O SSP1_SCK — Serial clock for SSP1.

IGP_CLKIN — General purpose clock input to the CGU.

OTRACECLK — Trace clock.

-R — Function reserved.

OI2S0_TX_MCLK — I2S transmit master clock.

I/O I2S0_RX_SCK — I2S receive clock. It is driven by the master

and received by the slave. Corresponds to the signal SCK in

the I2S-bus specification.

PF_5 E9 - 190 [5] N;

-R — Function reserved.

I/O U3_UCLK — Serial clock input/output for USART3 in

synchronous mode.

I/O SSP1_SSEL — Slave Select for SSP1.

OTRACEDATA[0] — Trace data, bit 0.

I/O GPIO7[19] — General purpose digital input/output pin.

-R — Function reserved.

I/O SGPIO4 — General purpose digital input/output pin.

-R — Function reserved.

AI ADC1_4 — ADC1 and ADC0, input channel 4. Configure the

pin as GPIO input and use the ADC function select register in

the SCU to select the ADC.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 53 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

PF_6 E7 - 192 [5] N;

-R — Function reserved.

I/O U3_DIR — RS-485/EIA-485 output enable/direction control for

USART3.

I/O SSP1_MISO — Master In Slave Out for SSP1.

OTRACEDATA[1] — Trace data, bit 1.

I/O GPIO7[20] — General purpose digital input/output pin.

-R — Function reserved.

I/O SGPIO5 — General purpose digital input/output pin.

I/O I2S1_TX_SDA — I2S1 transmit data. It is driven by the

transmitter and read by the receiver. Corresponds to the signal

SD in the I2S-bus specification.

AI ADC1_3 — ADC1 and ADC0, input channel 3. Configure the

pin as GPIO input and use the ADC function select register in

the SCU to select the ADC.

PF_7 B7 - 193 [5] N;

-R — Function reserved.

I/O U3_BAUD — Baud pin for USART3.

I/O SSP1_MOSI — Master Out Slave in for SSP1.

OTRACEDATA[2] — Trace data, bit 2.

I/O GPIO7[21] — General purpose digital input/output pin.

-R — Function reserved.

I/O SGPIO6 — General purpose digital input/output pin.

I/O I2S1_TX_WS — Transmit Word Select. It is driven by the

master and received by the slave. Corresponds to the signal

WS in the I2S-bus specification.

AI/

ADC1_7 — ADC1 and ADC0, input channel 7 or band gap

output. Configure the pin as GPIO input and use the ADC

function select register in the SCU to select the ADC.

PF_8 E6 - - [5] N;

-R — Function reserved.

I/O U0_UCLK — Serial clock input/output for USART0 in

synchronous mode.

ICTIN_2 — SCT input 2. Capture input 2 of timer 0.

OTRACEDATA[3] — Trace data, bit 3.

I/O GPIO7[22] — General purpose digital input/output pin.

-R — Function reserved.

I/O SGPIO7 — General purpose digital input/output pin.

-R — Function reserved.

AI ADC0_2 — ADC0 and ADC1, input channel 2. Configure the

pin as GPIO input and use the ADC function select register in

the SCU to select the ADC.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 54 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

PF_9 D6 - 203 [5] N;

-R — Function reserved.

I/O U0_DIR — RS-485/EIA-485 output enable/direction control for

USART0.

OCTOUT_1 — SCT output 1. Match output 3 of timer 3.

-R — Function reserved.

I/O GPIO7[23] — General purpose digital input/output pin.

-R — Function reserved.

I/O SGPIO3 — General purpose digital input/output pin.

-R — Function reserved.

AI ADC1_2 — ADC1 and ADC0, input channel 2. Configure the

pin as GPIO input and use the ADC function select register in

the SCU to select the ADC.

PF_10 A3 - 205 [5] N;

-R — Function reserved.

OU0_TXD — Transmitter output for USART0.

-R — Function reserved.

I/O GPIO7[24] — General purpose digital input/output pin.

-R — Function reserved.

ISD_WP — SD/MMC card write protect input.

-R — Function reserved.

AI ADC0_5 — ADC0 and ADC1, input channel 5. Configure the

pin as GPIO input and use the ADC function select register in

the SCU to select the ADC.

PF_11 A2 - 207 [5] N;

-R — Function reserved.

IU0_RXD — Receiver input for USART0.

-R — Function reserved.

I/O GPIO7[25] — General purpose digital input/output pin.

-R — Function reserved.

OSD_VOLT2 — SD/MMC bus voltage select output 2.

-R — Function reserved.

AI ADC1_5 — ADC1 and ADC0, input channel 5. Configure the

pin as GPIO input and use the ADC function select register in

the SCU to select the ADC.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 55 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

Clock pins

CLK0 N5 K3 62 [4] O;

OEMC_CLK0 — SDRAM clock 0.

OCLKOUT — Clock output pin.

-R — Function reserved.

I/O SD_CLK — SD/MMC card clock.

OEMC_CLK01 — SDRAM clock 0 and clock 1 combined.

I/O SSP1_SCK — Serial clock for SSP1.

IENET_TX_CLK (ENET_REF_CLK) — Ethernet Transmit

Clock (MII interface) or Ethernet Reference Clock (RMII

interface).

CLK1 T10 - - [4] O;

OEMC_CLK1 — SDRAM clock 1.

OCLKOUT — Clock output pin.

-R — Function reserved.

OCGU_OUT0 — CGU spare clock output 0.

-R — Function reserved.

OI2S1_TX_MCLK — I2S1 transmit master clock.

CLK2 D14 K6 141 [4] O;

OEMC_CLK3 — SDRAM clock 3.

OCLKOUT — Clock output pin.

-R — Function reserved.

I/O SD_CLK — SD/MMC card clock.

OEMC_CLK23 — SDRAM clock 2 and clock 3 combined.

OI2S0_TX_MCLK — I2S transmit master clock.

I/O I2S1_RX_SCK — Receive Clock. It is driven by the master

and received by the slave. Corresponds to the signal SCK in

the I2S-bus specification.

CLK3 P12 - - [4] O;

OEMC_CLK2 — SDRAM clock 2.

OCLKOUT — Clock output pin.

-R — Function reserved.

OCGU_OUT1 — CGU spare clock output 1.

-R — Function reserved.

I/O I2S1_RX_SCK — Receive Clock. It is driven by the master

and received by the slave. Corresponds to the signal SCK in

the I2S-bus specification.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 56 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

Debug pins

DBGEN L4 A6 41 [2] I I JTAG interface control signal. Also used for boundary scan. To

use the part in functional mode, connect this pin in one of the

following ways:

•Leave DBGEN open. The DBGEN pin is pulled up

internally by a 50 kΩ resistor.

•Tie DBGEN to VDDIO.

•Pull DBGEN up to VDDIO with an external pull-up

resistor.

TCK/SWDCLK J5 H2 38 [2] I; F I Test Clock for JTAG interface (default) or Serial Wire (SW)

clock.

TRST M4 B4 42 [2] I; PU I Test Reset for JTAG interface.

TMS/SWDIO K6 C4 44 [2] I; PU I Test Mode Select for JTAG interface (default) or SW debug

data input/output.

TDO/SWO K5 H3 46 [2] O O Test Data Out for JTAG interface (default) or SW trace output.

TDI J4 G3 35 [2] I; PU I Test Data In for JTAG interface.

USB0 pins

USB0_DP F2 E1 26 [6] - I/O USB0 bidirectional D+ line. Do not add an external series

resistor.

USB0_DM G2 E2 28 [6] - I/O USB0 bidirectional D line. Do not add an external series

resistor.

USB0_VBUS F1 E3 29 [6]

[7]

- I VBUS pin (power on USB cable). This pin includes an internal

pull-down resistor of 64 k (typical)  16 k.

USB0_ID H2 F1 30 [8] - I Indicates to the transceiver whether connected as an A-device

(USB0_ID LOW) or B-device (USB0_ID HIGH). For OTG this

pin has an internal pull-up resistor.

USB0_RREF H1 F3 32 [8] - 12.0 k (accuracy 1 %) on-board resistor to ground for current

reference.

USB1 pins

USB1_DP F12 E9 129 [9] - I/O USB1 bidirectional D+ line. Add an external series resistor of

33  +/- 2 %.

USB1_DM G12 E10 130 [9] - I/O USB1 bidirectional D line. Add an external series resistor of

33  +/- 2 %.

I2C-bus pins

I2C0_SCL L15 D6 132 [10] I; F I/O I2C clock input/output. Open-drain output (for I2C-bus

compliance).

I2C0_SDA L16 E6 133 [10] I; F I/O I2C data input/output. Open-drain output (for I2C-bus

compliance).

Reset and wake-up pins

RESET D9 B6 185 [11] I; IA I External reset input: A LOW on this pin resets the device,

causing I/O ports and peripherals to take on their default

states, and processor execution to begin at address 0. This

pin does not have an internal pull-up.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 57 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

WAKEUP0 A9 A4 187 [11] I; IA I External wake-up input; can raise an interrupt and can cause

wake-up from any of the low power modes. A pulse with a

duration of at least 45 ns wakes up the part.

Input 0 of the event monitor.No internal pull-up is enabled

when this pin is configured as input.

WAKEUP1 A10 - - [11] I; IA I External wake-up input; can raise an interrupt and can cause

wake-up from any of the low power modes. A pulse with a

duration of at least 45 ns wakes up the part.

Input 1 of the event monitor. No internal pull-up is enabled

when this pin is configured as input.

WAKEUP2 C9 - - [11] I; IA I External wake-up input; can raise an interrupt and can cause

wake-up from any of the low power modes. A pulse with a

duration of at least 45 ns wakes up the part.

Input 2 of the event monitor. This pin does not have an internal

pull-up.

WAKEUP3 D8 - - [11] I; IA I External wake-up input; can raise an interrupt and can cause

wake-up from any of the low power modes. A pulse with a

duration of at least 45 ns wakes up the part. This pin does not

have an internal pull-up.

ADC pins

ADC0_0/

ADC1_0/DAC

E3 A2 8 [8] I; IA I ADC input channel 0. Shared between 10-bit ADC0/1 and

DAC.

ADC0_1/

ADC1_1

C3 A1 4 [8] I; IA I ADC input channel 1. Shared between 10-bit ADC0/1.

ADC0_2/

ADC1_2

A4 B3 206 [8] I; IA I ADC input channel 2. Shared between 10-bit ADC0/1.

ADC0_3/

ADC1_3

B5 A3 200 [8] I; IA I ADC input channel 3. Shared between 10-bit ADC0/1.

ADC0_4/

ADC1_4

C6 - 199 [8] I; IA I ADC input channel 4. Shared between 10-bit ADC0/1.

ADC0_5/

ADC1_5

B3 - 208 [8] I; IA I ADC input channel 5. Shared between 10-bit ADC0/1.

ADC0_6/

ADC1_6

A5 - 204 [8] I; IA I ADC input channel 6. Shared between 10-bit ADC0/1.

ADC0_7/

ADC1_7

C5 - 197 [8] I; IA I ADC input channel 7. Shared between 10-bit ADC0/1.

RTC

RTC_ALARM A11 C3 186 [11] - O RTC controlled output.

RTCX1 A8 A5 182 [8] - I Input to the RTC 32 kHz ultra-low power oscillator circuit.

RTCX2 B8 B5 183 [8] - O Output from the RTC 32 kHz ultra-low power oscillator circuit.

SAMPLE B9 - - [11] O O Event monitor sample output.

Crystal oscillator pins

XTAL1 D1 B1 18 [8] - I Input to the oscillator circuit and internal clock generator

circuits.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 58 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

[1] N = neutral, input buffer disabled; no extra VDDIO current consumption if the input is driven midway between supplies; set the EZI bit in

the SFS register to enable the input buffer; I = input, OL = output driving LOW; OH = output driving HIGH; AI/O = analog input/output; IA

= inactive; PU = pull-up enabled (weak pull-up resistor pulls up pin to VDDIO; F = floating. Reset state reflects the pin state at reset

without boot code operation.

[2] 5 V tolerant pad with 15 ns glitch filter (5 V tolerant if VDDIO present; if VDDIO not present, do not exceed 3.6 V); provides digital I/O

functions with TTL levels and hysteresis; normal drive strength.

XTAL2 E1 C1 19 [8] - O Output from the oscillator amplifier.

Power and ground pins

USB0_VDDA

3V3_DRIVER

F3 D1 24 - - Separate analog 3.3 V power supply for driver.

USB0

_VDDA3V3

G3 D2 25 - - USB 3.3 V separate power supply voltage.

USB0_VSSA

_TERM

H3 D3 27 - - Dedicated analog ground for clean reference for termination

resistors.

USB0_VSSA

_REF

G1 F2 31 - - Dedicated clean analog ground for generation of reference

currents and voltages.

VDDA B4 B2 198 - - Analog power supply and ADC reference voltage.

VBAT B10 C5 184 - - RTC power supply: 3.3 V on this pin supplies power to the

RTC.

VDDREG F10, F9,

L8, L7

E4,

E5,

135,

188,

195,

82, 33

- Main regulator power supply. Tie the VDDREG and VDDIO

pins to a common power supply to ensure the same ramp-up

time for both supply voltages.

VPP E8 - - [12] - - OTP programming voltage.

VDDIO D7, E12,

F7, F8,

G10, H10,

J6, J7,

K7, L9,

L10, N7,

N13

F10,

6, 52,

57,

102,

110,

155,

160,

202

[12] - - I/O power supply. Tie the VDDREG and VDDIO pins to a

common power supply to ensure the same ramp-up time for

both supply voltages.

VSS G9, H7,

J10, J11,

C8,

D4,

D5,

G8,

J3,

-[13] - - Ground.

VSSIO C4, D13,

G6, G7,

G8, H8,

H9, J8,

J9, K9,

K10, M13,

P7, P13

- 5, 56,

109,

157

[13] - - Ground.

VSSA B2 C2 196 - - Analog ground.

Table 3. Pin description …continued

Pin name

LBGA256

TFBGA100

LQFP208

Reset state

[1]

Type

Description

Product data sheet Rev. 1.3 — 10 January 2020 59 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

[3] 5 V tolerant pad with 15 ns glitch filter (5 V tolerant if VDDIO present; if VDDIO not present, do not exceed 3.6 V); provides digital I/O

functions with TTL levels, and hysteresis; high drive strength.

[4] 5 V tolerant pad with 15 ns glitch filter (5 V tolerant if VDDIO present; if VDDIO not present, do not exceed 3.6 V); provides high-speed

digital I/O functions with TTL levels and hysteresis.

[5] 5 V tolerant pad providing digital I/O functions (with TTL levels and hysteresis) and analog input or output (5 V tolerant if VDDIO present;

if VDDIO not present, do not exceed 3.6 V). When configured as a ADC input or DAC output, the pin is not 5 V tolerant and the digital

section of the pad must be disabled by setting the pin to an input function and disabling the pull-up resistor through the pin’s SFSP

[6] 5 V tolerant transparent analog pad.

[7] For maximum load CL = 6.5 F and maximum resistance Rpd = 80 k, the VBUS signal takes about 2 s to fall from VBUS = 5 V to VBUS

= 0.2 V when it is no longer driven.

[8] Transparent analog pad. Not 5 V tolerant.

[9] Pad provides USB functions; 5 V tolerant if VDDIO present; if VDDIO not present, do not exceed 3.6 V. It is designed in accordance with

the USB specification, revision 2.0 (Full-speed and Low-speed mode only).

[10] Open-drain 5 V tolerant digital I/O pad, compatible with I2C-bus Fast Mode Plus specification. This pad requires an external pull-up to

provide output functionality. When power is switched off, this pin connected to the I2C-bus is floating and does not disturb the I2C lines.

[11] 5 V tolerant pad with 20 ns glitch filter; provides digital I/O functions with open-drain output and hysteresis.

[12] On the LQFP208, VPP is internally connected to VDDIO.

[13] On the LQFP208 package, VSSIO and VSS are connected to a common ground plane.

Product data sheet Rev. 1.3 — 10 January 2020 60 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

7. Functional description

7.1 Architectural overview

The ARM Cortex-M4 includes three AHB-Lite buses: the system bus, the I-CODE bus,

and the D-code bus. The I-CODE and D-code core buses allow for concurrent code and

data accesses from different slave ports.

The LPC436x use a multi-layer AHB matrix to connect the ARM Cortex-M4 buses and

other bus masters to peripherals in a flexible manner that optimizes performance by

allowing peripherals that are on different slaves ports of the matrix to be accessed

simultaneously by different bus masters.

An ARM Cortex-M0 co-processor is included in the LPC436x, capable of off-loading the

main ARM Cortex-M4 application processor. Most peripheral interrupts are connected to

both processors. The processors communicate with each other via an interprocessor

communication protocol.

7.2 ARM Cortex-M4 processor

The ARM Cortex-M4 CPU incorporates a 3-stage pipeline, uses a Harvard architecture

with separate local instruction and data buses as well as a third bus for peripherals, and

includes an internal prefetch unit that supports speculative branching. The ARM

Cortex-M4 supports single-cycle digital signal processing and SIMD instructions. A

hardware floating-point processor is integrated in the core. The processor includes a

NVIC with up to 53 interrupts.

7.3 ARM Cortex-M0 processors

The ARM Cortex-M0 processors are general purpose, 32-bit microprocessors, which offer

high performance and very low power consumption. The ARM Cortex-M0 processor uses

a 3-stage pipeline von Neumann architecture and a small but powerful instruction set

providing high-end processing hardware. The processors each incorporate an NVIC with

32 interrupts.

7.3.1 ARM Cortex-M0 coprocessor

The M0 coprocessor resides on the same AHB multi-layer matrix as the main Cortex-M0

core. The coprocessor can be used to off-load multiple tasks from the main Cortex-M4

processor.

7.3.2 ARM Cortex-M0 subsystem

The Cortex-M0 subsystem can be used to manage the SGPIO and SPI peripherals on the

M0 subsystem multilayer matrix but any other peripheral as well. The M0 subsystem is

separated by a bridge from the main AHB matrix. The M0 subsystem AHB matrix has two

SRAM blocks which allows to run the Cortex-M0 subsystem at full speed independently

from the main matrix.

Product data sheet Rev. 1.3 — 10 January 2020 61 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

One application of using the subsystem is to reduce power, for example when the main

matrix runs at a very low speed and the M0 subsystem monitors activity and increases the

main matrix speed when needed. Another application for the subsystem is to manage the

serial GPIO peripheral, which can be configured as additional SPI, I2S, or other serial

interface.

One of the two SRAM blocks connected to the subsystem AHB matrix is typically used for

code running on the M0 subsystem and the other SRAM block for data. This allows other

bus masters to access the data SRAM without interrupting the M0 processor instruction

fetches and thereby stalling the M0 subsystem.

The M0 subsystem matrix runs at an asynchronous speed from the main matrix. This

allows to operate the SGPIO at any desired frequency. The M0 subsystem can control the

SGPIO in a deterministic way, without incurring latency that occurs when the M4 controls

the SGPIO through a bridge.

7.4 Interprocessor communication

The ARM Cortex-M4 and ARM Cortex-M0 interprocessor communication is based on

using shared SRAM as mailbox and one processor raising an interrupt on the other

processor's NVIC, for example after it has delivered a new message in the mailbox. The

receiving processor can reply by raising an interrupt on the sending processor's NVIC to

acknowledge the message.

Product data sheet Rev. 1.3 — 10 January 2020 62 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

7.5 AHB multilayer matrix

Fig 5. AHB multilayer matrix master and slave connections

ARM

CORTEX-M4

TEST/DEBUG

INTERFACE

ARM

CORTEX-M0

APPLICATION

TEST/DEBUG

INTERFACE

ARM

CORTEX-M0

SUBSYSTEM

TEST/DEBUG

INTERFACE

DMA ETHERNET USB1

USB0

LCD SD/

MMC

EXTERNAL

MEMORY

CONTROLLER

32 kB AHB SRAM

16 kB + 16 kB

AHB SRAM

64 kB ROM

32 kB LOCAL SRAM

40 kB LOCAL SRAM

System

bus

I-

code

bus

D-

code

bus

masters

slaves

AHB MULTILAYER MATRIX

= master-slave connection

AHB PERIPHERALS

INTERFACES

aaa-018953

SPIFI

APB0 PERIPHERALS

SPI

16 kB SRAM

SGPIO

BRIDGE

BRIDGE0

BRIDGE

master

HIGH--

SPEED

PHY 2 kB SRAM

FPU

MPU

RTC PERIPHERALS

slaves

512 kB FLASH A

512 kB FLASH B

16 kB EEPROM

Product data sheet Rev. 1.3 — 10 January 2020 63 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

7.6 Nested Vectored Interrupt Controller (NVIC)

The NVIC is an integral part of the Cortex-M4. The tight coupling to the CPU allows for low

interrupt latency and efficient processing of late arriving interrupts.

The ARM Cortex-M0 co-processor has its own NVIC with 32 vectored interrupts. Most

peripheral interrupts are shared between the Cortex-M0 and Cortex-M4 NVICs.

7.6.1 Features

•ARM Cortex-M4 core:

–Controls system exceptions and peripheral interrupts

–Support for up to 53 vectored interrupts

–Eight programmable interrupt priority levels with hardware priority level masking

–Relocatable vector table

–Non-Maskable Interrupt (NMI)

–Software interrupt generation

•ARM Cortex-M0 core:

–Support for up to 32 interrupts

–Four programmable interrupt priority levels with hardware priority level masking

7.6.2 Interrupt sources

Each peripheral device has one interrupt line connected to the NVIC but may have several

interrupt flags. Individual interrupt flags may also represent more than one interrupt

source.

7.7 System Tick timer (SysTick)

The ARM Cortex-M4 includes a system tick timer (SYSTICK) that is intended to generate

a dedicated SYSTICK exception at a 10 ms interval.

Remark: The SysTick is not included in the ARM Cortex-M0 core implementation.

7.8 Event router

The event router combines various internal signals, interrupts, and the external interrupt

pins (WAKEUP[3:0]) to create an interrupt in the NVIC, if enabled. In addition, the event

router creates a wake-up signal to the ARM core and the CCU for waking up from Sleep,

Deep-sleep, Power-down, and Deep power-down modes. Individual events can be

configured as edge or level sensitive and can be enabled or disabled in the event router.

The event router can be battery powered.

The following events if enabled in the event router can create a wake-up signal from

sleep, deep-sleep, power-down, and deep power-down modes and/or create an interrupt:

•External pins WAKEUP0/1/2/3 and RESET

•Alarm timer, RTC (32 kHz oscillator running)

The following events if enabled in the event router can create a wake-up signal from sleep

mode only and/or create an interrupt:

Product data sheet Rev. 1.3 — 10 January 2020 64 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

•WWDT, BOD interrupts

•C_CAN0/1 and QEI interrupts

•Ethernet, USB0, USB1 signals

•Selected outputs of combined timers (SCTimer/PWM and timer 0/1/3)

Remark: Any interrupt can wake up the ARM Cortex-M4 from sleep mode if enabled in

the NVIC.

7.9 Global Input Multiplexer Array (GIMA)

The GIMA allows to route signals to event-driven peripheral targets like the

SCTimer/PWM, timers, event router, or the ADCs.

7.9.1 Features

•Single selection of a source.

•Signal inversion.

•Can capture a pulse if the input event source is faster than the target clock.

•Synchronization of input event and target clock.

•Single-cycle pulse generation for target.

7.10 On-chip static RAM

The LPC436x support up to 154 kB SRAM with separate bus master access for higher

throughput and individual power control for low power operation.

7.11 On-chip flash memory

The LPC436x contain up to 1 MB of dual-bank flash program memory. With dual-bank

flash memory, the user code can write or erase one flash bank while reading the other

flash bank without interruption. A two-port flash accelerator maximizes the flash

performance.

In-System Programming (ISP) and In-Application Programming (IAP) routines for

programming the flash memory are provided in the Boot ROM.

7.12 EEPROM

The LPC436x contain 16 kB of on-chip byte-erasable and byte-programmable EEPROM

memory.

The EEPROM memory is divided into 128 pages. The user can access pages 1 through

127. Page 128 is protected.

7.13 Boot ROM

The internal ROM memory is used to store the boot code of the LPC436x. After a reset,

the ARM processor will start its code execution from this memory.

The boot ROM memory includes the following features:

•The ROM memory size is 64 kB.

Product data sheet Rev. 1.3 — 10 January 2020 65 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

•Supports booting from external static memory such as NOR flash, SPI flash, quad SPI

flash, USB0, and USB1.

•Includes API for OTP programming.

•Includes a flexible USB device stack that supports Human Interface Device (HID),

Mass Storage Class (MSC), and Device Firmware Upgrade (DFU) drivers.

Several boot modes are available if P2_7 is LOW on reset depending on the values of the

OTP bits BOOT_SRC. If the OTP memory is not programmed or the BOOT_SRC bits are

all zero, the boot mode is determined by the states of the boot pins P2_9, P2_8, P1_2,

and P1_1.

[1] The boot loader programs the appropriate pin function at reset to boot using either SSP0 or SPIFI.

Remark: Pin functions for SPIFI and SSP0 boot are different.

Table 4. Boot mode when OTP BOOT_SRC bits are programmed

Boot mode BOOT_SRC

bit 3

BOOT_SRC

bit 2

BOOT_SRC

bit 1

BOOT_SRC

bit 0

Description

Pin state 0 0 0 0 Boot source is defined by the reset state of P1_1,

P1_2, P2_8 pins, and P2_9. See Table 5.

USART0 0 0 0 1 Enter ISP mode using USART0 pins P2_0 and

P2_1.

SPIFI 0 0 1 0 Boot from Quad SPI flash connected to the SPIFI

interface using pins P3_3 to P3_8.

EMC 8-bit 0 0 1 1 Boot from external static memory (such as NOR

flash) using CS0 and an 8-bit data bus.

EMC 16-bit 0 1 0 0 Boot from external static memory (such as NOR

flash) using CS0 and a 16-bit data bus.

EMC 32-bit 0 1 0 1 Boot from external static memory (such as NOR

flash) using CS0 and a 32-bit data bus.

USB0 0 1 1 0 Boot from USB0.

USB1 0 1 1 1 Boot from USB1.

SPI (SSP) 1 0 0 0 Boot from SPI flash connected to the SSP0

interface on P3_3 (function SSP0_SCK), P3_6

(function SSP0_SSEL), P3_7 (function

SSP0_MISO), and P3_8 (function SSP0_MOSI)[1].

USART3 1 0 0 1 Enter ISP mode using USART3 pins P2_3 and

P2_4.

Table 5. Boot mode when OPT BOOT_SRC bits are zero

Boot mode Pins Description

P2_9 P2_8 P1_2 P1_1

USART0 LOW LOW LOW LOW Enter ISP mode using USART0 pins P2_0 and

P2_1.

SPIFI LOW LOW LOW HIGH Boot from Quad SPI flash connected to the SPIFI

interface on P3_3 to P3_8[1].

EMC 8-bit LOW LOW HIGH LOW Boot from external static memory (such as NOR

flash) using CS0 and an 8-bit data bus.

EMC 16-bit LOW LOW HIGH HIGH Boot from external static memory (such as NOR

flash) using CS0 and a 16-bit data bus.

Product data sheet Rev. 1.3 — 10 January 2020 66 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

[1] The boot loader programs the appropriate pin function at reset to boot using either SSP0 or SPIFI.

Remark: Pin functions for SPIFI and SSP0 boot are different.

7.14 Memory mapping

The memory map shown in Figure 6 and Figure 7 is global to both the Cortex-M4 and the

Cortex-M0 processors and all SRAM, flash, and EEPROM memory is shared between

both processors. Each processor uses its own ARM private bus memory map for the

NVIC and other system functions.

EMC 32-bit LOW HIGH LOW LOW Boot from external static memory (such as NOR

flash) using CS0 and a 32-bit data bus.

USB0 LOW HIGH LOW HIGH Boot from USB0

USB1 LOW HIGH HIGH LOW Boot from USB1.

SPI (SSP) LOW HIGH HIGH HIGH Boot from SPI flash connected to the SSP0

interface on P3_3 (function SSP0_SCK), P3_6

(function SSP0_SSEL), P3_7 (function

SSP0_MISO), and P3_8 (function SSP0_MOSI)[1].

USART3 HIGH LOW LOW LOW Enter ISP mode using USART3 pins P2_3 and

P2_4.

Table 5. Boot mode when OPT BOOT_SRC bits are zero

Boot mode Pins Description

P2_9 P2_8 P1_2 P1_1

Product data sheet Rev. 1.3 — 10 January 2020 67 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

Fig 6. LPC436x Memory mapping (overview)

reserved

peripheral bit band alias region

reserved

high-speed GPIO

reserved

0x0000 0000

0 GB

1 GB

4 GB

0x2200 0000

0x2400 0000

0x2800 0000

0x1000 0000

0x3000 0000

0x4000 0000

0x4001 2000

0x4004 0000

0x4005 0000

0x4010 0000

0x4400 0000

0x6000 0000

AHB peripherals

APB peripherals #0

APB peripherals #1

reserved

RTC domain peripherals

0x4006 0000

0x4008 0000

0x4009 0000

0x400A 0000

0x400B 0000

0x400C 0000

0x400D 0000

0x400E 0000

0x400F 0000

0x400F 1000

0x400F 2000

0x400F 4000

0x400F 8000

clocking/reset peripherals

APB peripherals #2

APB peripherals #3

0x2004 0000

4 x 16 kB AHB SRAM

0x2004 4000

16 kB EEPROM

SGPIO

SPI

0x4010 1000

0x4010 2000

0x4200 0000

reserved

local SRAM/

external static memory banks

0x2000 0000

0x2001 0000

128 MB dynamic external memory DYCS0

256 MB dynamic external memory DYCS1

256 MB dynamic external memory DYCS2

256 MB dynamic external memory DYCS3 0x7000 0000

0x8000 0000

0x8800 0000

0xE000 0000

256 MB shadow area

LPC436x

reserved

32 MB AHB SRAM bit banding

reserved

0xE010 0000

0xFFFF FFFF

reserved

128 MB SPIFI data

ARM private bus

reserved

aaa-018954

reserved

0x1000 0000

0x1000 8000

0x1008 0000

0x1008 A000

0x1040 0000

0x1041 0000

0x1C00 0000

0x1D00 0000

32 kB local SRAM

32 kB + 8 kB local SRAM

reserved

64 kB ROM

0x1E00 0000

0x1F00 0000

0x2000 0000

16 MB static external memory CS3

16 MB static external memory CS2

16 MB static external memory CS1

16 MB static external memory CS0

0x1400 0000

0x1800 0000

0x1800 4000

0x1800 4800

0x1840 0000

0x1840 2000

0x1A00 0000 256 kB flash A

0x1A04 0000 256 kB flash A

0x1A08 0000

0x1B00 0000 256 kB flash B

0x1B04 0000 256 kB flash B

0x1B08 0000

64 MB SPIFI data

16 kB SRAM (M0 subsystem)

2 kB SRAM (M0 subsystem)

8 kB ROM (M0 SERIAL)

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

Product data sheet Rev. 1.3 — 10 January 2020 68 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

Fig 7. LPC436x Memory mapping (peripherals)

reserved

peripheral bit band alias region

high-speed GPIO

reserved

0x4000 0000

0x0000 0000

0x1000 0000

0x4002 0000

0x4004 0000

0x4005 0000

0x4010 0000

0x4400 0000

0x6000 0000

0xFFFF FFFF

AHB peripherals

APB0 peripherals

APB1 peripherals

reserved

RTC domain peripherals

0x4006 0000

0x4008 0000

0x4009 0000

0x400A 0000

0x400B 0000

0x400C 0000

0x400D 0000

0x400E 0000

0x400F 0000

0x400F 1000

0x400F 2000

0x400F 4000

0x400F 8000

clocking/reset peripherals

APB2 peripherals

APB3 peripherals

SGPIO

SPI

0x4010 1000

0x4010 2000

0x4200 0000

reserved

external memories and

ARM private bus

APB2

peripherals

0x400C 1000

0x400C 2000

0x400C 3000

0x400C 4000

0x400C 6000

0x400C 8000

0x400C 7000

0x400C 5000

0x400C 0000 RI timer

USART2

USART3

timer2

timer3

SSP1

QEI

APB1

peripherals

0x400A 1000

0x400A 2000

0x400A 3000

0x400A 4000

0x400A 5000

0x400B 0000

0x400A 0000 motor control PWM

I2C0

I2S0

I2S1

C_CAN1

reserved

AHB

peripherals

0x4000 1000

0x4000 0000

SCT

0x4000 2000

0x4000 3000

0x4000 4000

0x4000 6000

0x4000 8000

0x4001 0000

0x4001 2000

0x4002 0000

0x4000 9000

0x4000 7000

0x4000 5000

DMA

SD/MMC

EMC

USB1

LCD

USB0

reserved

SPIFI

ethernet

reserved

0x4008 1000

0x4008 0000 WWDT

0x4008 2000

0x4008 3000

0x4008 4000

0x4008 6000

0x4008 A000

0x4008 7000

0x4008 8000

0x4008 9000

0x4008 5000

UART1 w/ modem

SSP0

timer0

timer1

SCU

GPIO interrupts

GPIO GROUP0 interrupt

GPIO GROUP1 interrupt

USART0

RTC domain

peripherals

0x4004 1000

0x4004 0000

alarm timer

0x4004 2000

0x4004 3000

0x4004 4000

0x4004 6000

0x4004 7000

0x4005 0000

0x4004 5000

power mode control

CREG

event router

OTP controller

reserved

RTC/event monitor

backup registers

clocking

reset control

peripherals

0x4005 1000

0x4005 0000

CGU

0x4005 2000

0x4005 3000

0x4005 4000

0x4006 0000

CCU2

RGU

CCU1

LPC436x

aaa-018955

reserved

APB3

peripherals

0x400E 1000

0x400E 2000

0x400E 3000

0x400E 4000

0x400F 0000

0x400E 5000

0x400E 0000 I2C1

DAC

C_CAN0

ADC0

ADC1

reserved

GIMA

APB0

peripherals

256 MB memory shadow area

SRAM, flash, EEPROM memories

external memory banks

0x4000 C000

0x4000 D000

reserved

flash A controller

flash B controller

0x4000 E000

0x4000 F000

EEPROM controller

Product data sheet Rev. 1.3 — 10 January 2020 69 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

7.15 One-Time Programmable (OTP) memory

The OTP provides 64 bit+ 256 bit of memory for general-purpose use.

7.16 General Purpose I/O (GPIO)

The LPC436x provide eight GPIO ports with up to 31 GPIO pins each.

Device pins that are not connected to a specific peripheral function are controlled by the

GPIO registers. Pins may be dynamically configured as inputs or outputs. Separate

registers allow setting or clearing any number of outputs simultaneously. The value of the

output register may be read back as well as the current state of the port pins.

All GPIO pins default to inputs with pull-up resistors enabled and input buffer disabled on

reset. The input buffer must be turned on in the system control block SFS register before

the GPIO input can be read.

7.16.1 Features

•Accelerated GPIO functions:

–GPIO registers are located on the AHB so that the fastest possible I/O timing can

be achieved.

–Mask registers allow treating sets of port bits as a group, leaving other bits

unchanged.

–All GPIO registers are byte and half-word addressable.

–Entire port value can be written in one instruction.

•Bit-level set and clear registers allow a single instruction set or clear of any number of

bits in one port.

•Direction control of individual bits.

•Up to eight GPIO pins can be selected from all GPIO pins to create an edge- or

level-sensitive GPIO interrupt request (GPIO interrupts).

•Two GPIO group interrupts can be triggered by any pin or pins in each port (GPIO

group0 and group1 interrupts).

7.17 Configurable digital peripherals

7.17.1 SCTimer/PWM

The SCTimer/PWM allows a wide variety of timing, counting, output modulation, and input

capture operations. The inputs and outputs of the SCTimer/PWM are shared with the

capture and match inputs/outputs of the 32-bit general purpose counter/timers.

The SCTimer/PWM can be configured as two 16-bit counters or a unified 32-bit counter. In

the two-counter case, in addition to the counter value the following operational elements

are independent for each half:

•State variable.

•Limit, halt, stop, and start conditions.

•Values of Match/Capture registers, plus reload or capture control values.

Product data sheet Rev. 1.3 — 10 January 2020 70 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

In the two-counter case, the following operational elements are global to the

SCTimer/PWM, but the last three can use match conditions from either counter:

•Clock selection

•Inputs

•Events

•Outputs

•Interrupts

7.17.1.1 Features

•Two 16-bit counters or one 32-bit counter.

•Counters clocked by bus clock or selected input.

•Up counters or up-down counters.

•State variable allows sequencing across multiple counter cycles.

•The following conditions define an event: a counter match condition, an input (or

output) condition, a combination of a match and/or and input/output condition in a

specified state.

•Events control outputs, interrupts, and DMA requests.

–Match register 0 can be used as an automatic limit.

–In bi-directional mode, events can be enabled based on the count direction.

–Match events can be held until another qualifying event occurs.

•Selected events can limit, halt, start, or stop a counter.

•Supports:

–8 inputs

–16 outputs

–16 match/capture registers

–16 events

–32 states

–Match register 0 to 5 support a fractional component for the dither engine

7.17.2 Serial GPIO (SGPIO)

The Serial GPIOs offer standard GPIO functionality enhanced with features to accelerate

serial stream processing.

7.17.2.1 Features

•Each SGPIO input/output slice can be used to perform a serial to parallel or parallel to

serial data conversion.

•16 SGPIO input/output slices each with a 32-bit FIFO that can shift the input value

from a pin or an output value to a pin with every cycle of a shift clock.

•Each slice is double-buffered.

•Interrupt is generated on a full FIFO, shift clock, or pattern match.

•Slices can be concatenated to increase buffer size.

Product data sheet Rev. 1.3 — 10 January 2020 71 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

•Each slice has a 32-bit pattern match filter.

7.18 AHB peripherals

7.18.1 General Purpose DMA

The DMA controller allows peripheral-to memory, memory-to-peripheral,

peripheral-to-peripheral, and memory-to-memory transactions. Each DMA stream

provides unidirectional serial DMA transfers for a single source and destination. For

example, a bidirectional port requires one stream for transmit and one for receives. The

source and destination areas can each be either a memory region or a peripheral for

master 1, but only memory for master 0.

7.18.1.1 Features

•Eight DMA channels. Each channel can support a unidirectional transfer.

•16 DMA request lines.

•Single DMA and burst DMA request signals. Each peripheral connected to the DMA

Controller can assert either a burst DMA request or a single DMA request. The DMA

burst size is set by programming the DMA Controller.

•Memory-to-memory, memory-to-peripheral, peripheral-to-memory, and

peripheral-to-peripheral transfers are supported.

•Scatter or gather DMA is supported through the use of linked lists. This means that

the source and destination areas do not have to occupy contiguous areas of memory.

•Hardware DMA channel priority.

•AHB slave DMA programming interface. The DMA Controller is programmed by

writing to the DMA control registers over the AHB slave interface.

•Two AHB bus masters for transferring data. These interfaces transfer data when a

DMA request goes active. Master 1 can access memories and peripherals, master 0

can access memories only.

•32-bit AHB master bus width.

•Incrementing or non-incrementing addressing for source and destination.

•Programmable DMA burst size. The DMA burst size can be programmed to more

efficiently transfer data.

•Internal four-word FIFO per channel.

•Supports 8, 16, and 32-bit wide transactions.

•Big-endian and little-endian support. The DMA Controller defaults to little-endian

mode on reset.

•An interrupt to the processor can be generated on a DMA completion or when a DMA

error has occurred.

•Raw interrupt status. The DMA error and DMA count raw interrupt status can be read

prior to masking.

7.18.2 SPI Flash Interface (SPIFI)

The SPI Flash Interface allows low-cost serial flash memories to be connected to the ARM

Cortex-M4 processor with little performance penalty compared to parallel flash devices

with higher pin count.

Product data sheet Rev. 1.3 — 10 January 2020 72 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

After a few commands configure the interface at startup, the entire flash content is

accessible as normal memory using byte, halfword, and word accesses by the processor

and/or DMA channels. Simple sequences of commands handle erasing and

programming.

Many serial flash devices use a half-duplex command-driven SPI protocol for device setup

and initialization and then move to a half-duplex, command-driven 4-bit protocol for

normal operation. Different serial flash vendors and devices accept or require different

commands and command formats. SPIFI provides sufficient flexibility to be compatible

with common flash devices and includes extensions to help insure compatibility with future

devices.

7.18.2.1 Features

•Interfaces to serial flash memory in the main memory map.

•Supports classic and 4-bit bidirectional serial protocols.

•Half-duplex protocol compatible with various vendors and devices.

•Quad SPI Flash Interface (SPIFI) with 1-, 2-, or 4-bit data at rates of up to 52 MB per

second.

•Supports DMA access.

7.18.3 SD/MMC card interface

The SD/MMC card interface supports the following modes to control:

•Secure Digital memory (SD version 3.0)

•Secure Digital I/O (SDIO version 2.0)

•Consumer Electronics Advanced Transport Architecture (CE-ATA version 1.1)

•MultiMedia Cards (MMC version 4.4)

7.18.4 External Memory Controller (EMC)

Remark: The EMC is available on all LPC436x parts. The following memory bus widths

are supported:

•LBGA256 packages: 32 bit

•TFBGA100 packages: 16 bit

•LQFP208 packages: 16 bit

The LPC436x EMC is a Memory Controller peripheral offering support for asynchronous

static memory devices such as RAM, ROM, and NOR flash. In addition, it can be used as

an interface with off-chip memory-mapped devices and peripherals.

Table 6. EMC pinout for different packages

Function LBGA256 TFBGA100 LQFP208

A EMC_A[23:0] EMC_A[13:0] EMC_A[23:0]

D EMC_D[31:0] EMC_D[15:0] EMC_D[15:0]

BLS EMC_BLS[3:0] EMC_BLS0 EMC_BLS[1:0]

CS EMC_CS[3:0] EMC_CS0 EMC_CS[3:0]

OE EMC_OE EMC_OE EMC_OE

Product data sheet Rev. 1.3 — 10 January 2020 73 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

7.18.4.1 Features

•Dynamic memory interface support including single data rate SDRAM.

•Asynchronous static memory device support including RAM, ROM, and NOR flash,

with or without asynchronous page mode.

•Low transaction latency.

•Read and write buffers to reduce latency and to improve performance.

•8/16/32 data and 24 address lines wide static memory support.

•16 bit and 32 bit wide chip select SDRAM memory support.

•Static memory features include:

–Asynchronous page mode read

–Programmable Wait States

–Bus turnaround delay

–Output enable and write enable delays

–Extended wait

•Four chip selects for synchronous memory and four chip selects for static memory

devices.

•Power-saving modes dynamically control EMC_CKEOUT and EMC_CLK signals to

SDRAMs.

•Dynamic memory self-refresh mode controlled by software.

•Controller supports 2048 (A0 to A10), 4096 (A0 to A11), and 8192 (A0 to A12) row

address synchronous memory parts. Those are typically 512 MB, 256 MB, and

128 MB parts, with 4, 8, 16, or 32 data bits per device.

•Separate reset domains allow the for auto-refresh through a chip reset if desired.

•SDRAM clock can run at full or half the Cortex-M4 core frequency.

Note: Synchronous static memory devices (synchronous burst mode) are not supported.

WE EMC_WE EMC_WE EMC_WE

CKEOUT EMC_

CKEOUT[3:0]

EMC_

CKEOUT[1:0]

EMC_

CKEOUT[1:0]

CLK EMC_CLK[3:0];

EMC_CLK01,

EMC_CLK23

EMC_CLK0, EMC_CLK3;

EMC_CLK01,

EMC_CLK23

EMC_CLK0, EMC_CLK3;

EMC_CLK01,

EMC_CLK23

DQMOUT EMC_

DQMOUT[3:0]

- EMC_

DQMOUT[1:0]

DYCS EMC_

DYCS[3:0]

EMC_DYCS[1:0] EMC_DYCS[2:0]

CAS EMC_CAS EMC_CAS EMC_CAS

RAS EMC_RAS EMC_RAS EMC_RAS

Table 6. EMC pinout for different packages

Function LBGA256 TFBGA100 LQFP208

Product data sheet Rev. 1.3 — 10 January 2020 74 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

7.18.5 High-speed USB Host/Device/OTG interface (USB0)

Remark: USB0 is available on the following parts: LPC435x, LPC433x, LPC432x. USB0

is not available on the LPC431x parts.

The USB OTG module allows the LPC436x to connect directly to a USB Host such as a

PC (in device mode) or to a USB Device in host mode.

7.18.5.1 Features

•Contains UTMI+ compliant high-speed transceiver (PHY).

•Complies with Universal Serial Bus specification 2.0.

•Complies with USB On-The-Go supplement.

•Complies with Enhanced Host Controller Interface Specification.

•Supports auto USB 2.0 mode discovery.

•Supports all high-speed USB-compliant peripherals.

•Supports all full-speed USB-compliant peripherals.

•Supports software Host Negotiation Protocol (HNP) and Session Request Protocol

(SRP) for OTG peripherals.

•Supports interrupts.

•Supports Start Of Frame (SOF) frame length adjust.

•This module has its own, integrated DMA engine.

•USB interface electrical test software included in ROM USB stack.

7.18.6 High-speed USB Host/Device interface with ULPI (USB1)

Remark: USB1 is available on the following parts: LPC435x and LPC433x. USB1 is not

available on the LPC432x and LPC431x parts.

The USB1 interface can operate as a full-speed USB Host/Device interface or can

connect to an external ULPI PHY for High-speed operation.

7.18.6.1 Features

•Complies with Universal Serial Bus specification 2.0.

•Complies with Enhanced Host Controller Interface Specification.

•Supports auto USB 2.0 mode discovery.

•Supports all high-speed USB-compliant peripherals if connected to external ULPI

PHY.

•Supports all full-speed USB-compliant peripherals.

•Supports interrupts.

•Supports Start Of Frame (SOF) frame length adjust.

•This module has its own, integrated DMA engine.

•USB interface electrical test software included in ROM USB stack.

7.18.7 LCD controller

Remark: The LCD controller is only available on parts LPC435x. LCD is not available on

parts LPC433x, LPC432x, and LPC431x.

Product data sheet Rev. 1.3 — 10 January 2020 75 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

The LCD controller provides all of the necessary control signals to interface directly to

various color and monochrome LCD panels. Both STN (single and dual panel) and TFT

panels can be operated. The display resolution is selectable and can be up to 1024  768

pixels. Several color modes are provided, up to a 24-bit true-color non-palettized mode.

An on-chip 512 byte color palette allows reducing bus utilization (that is, memory size of

the displayed data) while still supporting many colors.

The LCD interface includes its own DMA controller to allow it to operate independently of

the CPU and other system functions. A built-in FIFO acts as a buffer for display data,

providing flexibility for system timing. Hardware cursor support can further reduce the

amount of CPU time required to operate the display.

7.18.7.1 Features

•AHB master interface to access frame buffer.

•Setup and control via a separate AHB slave interface.

•Dual 16-deep programmable 64-bit wide FIFOs for buffering incoming display data.

•Supports single and dual-panel monochrome Super Twisted Nematic (STN) displays

with 4-bit or 8-bit interfaces.

•Supports single and dual-panel color STN displays.

•Supports Thin Film Transistor (TFT) color displays.

•Programmable display resolution including, but not limited to: 320  200, 320  240,

640  200, 640  240, 640  480, 800  600, and 1024  768.

•Hardware cursor support for single-panel displays.

•15 gray-level monochrome, 3375 color STN, and 32 K color palettized TFT support.

•1, 2, or 4 bits-per-pixel (bpp) palettized displays for monochrome STN.

•1, 2, 4, or 8 bpp palettized color displays for color STN and TFT.

•16 bpp true-color non-palettized for color STN and TFT.

•24 bpp true-color non-palettized for color TFT.

•Programmable timing for different display panels.

•256 entry, 16-bit palette RAM, arranged as a 128  32-bit RAM.

•Frame, line, and pixel clock signals.

•AC bias signal for STN, data enable signal for TFT panels.

•Supports little and big-endian, and Windows CE data formats.

•LCD panel clock may be generated from the peripheral clock, or from a clock input

pin.

7.18.8 Ethernet

Remark: The ethernet controller is available on parts LPC435x and LPC433x. Ethernet is

not available on parts LPC432x and LPC431x.

7.18.8.1 Features

•10/100 Mbit/s

•DMA support

•Power management remote wake-up frame and magic packet detection

Product data sheet Rev. 1.3 — 10 January 2020 76 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

•Supports both full-duplex and half-duplex operation

–Supports CSMA/CD Protocol for half-duplex operation.

–Supports IEEE 802.3x flow control for full-duplex operation.

–Optional forwarding of received pause control frames to the user application in

full-duplex operation.

–Back-pressure support for half-duplex operation.

–Automatic transmission of zero-quanta pause frame on deassertion of flow control

input in full-duplex operation.

•Supports IEEE1588 time stamping and IEEE 1588 advanced time stamping (IEEE

1588-2008 v2).

7.19 Digital serial peripherals

7.19.1 UART1

Remark: The LPC436x contain one UART with standard transmit and receive data lines.

UART1 also provides a full modem control handshake interface and support for

RS-485/9-bit mode allowing both software address detection and automatic address

detection using 9-bit mode.

UART1 includes a fractional baud rate generator. Standard baud rates such as 115 200 Bd

can be achieved with any crystal frequency above 2 MHz.

7.19.1.1 Features

•Maximum UART data bit rate of 8 MBit/s.

•16 B Receive and Transmit FIFOs.

•Register locations conform to 16C550 industry standard.

•Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B.

•Built-in fractional baud rate generator covering wide range of baud rates without a

need for external crystals of particular values.

•Auto baud capabilities and FIFO control mechanism that enables software flow

control implementation.

•Equipped with standard modem interface signals. This module also provides full

support for hardware flow control.

•Support for RS-485/9-bit/EIA-485 mode (UART1).

•DMA support.

7.19.2 USART0/2/3

Remark: The LPC436x contain three USARTs. In addition to standard transmit and

receive data lines, the USARTs support a synchronous mode.

The USARTs include a fractional baud rate generator. Standard baud rates such as

115 200 Bd can be achieved with any crystal frequency above 2 MHz.

7.19.2.1 Features

•Maximum UART data bit rate of 8 MBit/s.

Product data sheet Rev. 1.3 — 10 January 2020 77 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

•16 B Receive and Transmit FIFOs.

•Register locations conform to 16C550 industry standard.

•Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B.

•Built-in fractional baud rate generator covering wide range of baud rates without a

need for external crystals of particular values.

•Auto baud capabilities and FIFO control mechanism that enables software flow

control implementation.

•Support for RS-485/9-bit/EIA-485 mode.

•USART3 includes an IrDA mode to support infrared communication.

•All USARTs have DMA support.

•Support for synchronous mode at a data bit rate of up to 8 Mbit/s.

•Smart card mode conforming to ISO7816 specification

7.19.3 SPI serial I/O controller

Remark: The LPC436x contain one SPI controller.

SPI is a full duplex serial interface designed to handle multiple masters and slaves

connected to a given bus. Only a single master and a single slave can communicate on

the interface during a given data transfer. During a data transfer the master always sends

8 bits to 16 bits of data to the slave, and the slave always sends 8 bits to 16 bits of data to

the master.

7.19.3.1 Features

•Maximum SPI data bit rate 25 Mbit/s.

•Compliant with SPI specification

•Synchronous, serial, full duplex communication

•Combined SPI master and slave

•Maximum data bit rate of one eighth of the input clock rate

•8 bits to 16 bits per transfer

7.19.4 SSP serial I/O controller

Remark: The LPC436x contain two SSP controllers.

The SSP controller can operate on a SPI, 4-wire SSI, or Microwire bus. It can interact with

multiple masters and slaves on the bus. Only a single master and a single slave can

communicate on the bus during a given data transfer. The SSP supports full duplex

transfers, with frames of 4 bit to 16 bit of data flowing from the master to the slave and

from the slave to the master. In practice, often only one of these data flows carries

meaningful data.

7.19.4.1 Features

•Maximum SSP speed in full-duplex mode of 25 Mbit/s; for transmit only 50 Mbit/s

(master) and 15 Mbit/s (slave)

•Compatible with Motorola SPI, 4-wire Texas Instruments SSI, and National

Semiconductor Microwire buses

Product data sheet Rev. 1.3 — 10 January 2020 78 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

•Synchronous serial communication

•Master or slave operation

•8-frame FIFOs for both transmit and receive

•4-bit to 16-bit frame

•DMA transfers supported by GPDMA

7.19.5 I2C-bus interface

Remark: The LPC436x each contain two I2C-bus interfaces.

The I2C-bus is bidirectional for inter-IC control using only two wires: a Serial Clock line

(SCL) and a Serial Data line (SDA). Each device is recognized by a unique address and

can operate as either a receiver-only device (for example an LCD driver) or a transmitter

with the capability to both receive and send information (such as memory). Transmitters

and/or receivers can operate in either master or slave mode, depending on whether the

chip has to initiate a data transfer or is only addressed. The I2C is a multi-master bus and

can be controlled by more than one bus master connected to it.

7.19.5.1 Features

•I2C0 is a standard I2C compliant bus interface with open-drain pins. I2C0 also

supports Fast mode plus with bit rates up to 1 Mbit/s.

•I2C1 uses standard I/O pins with bit rates of up to 400 kbit/s (Fast I2C-bus).

•Easy to configure as master, slave, or master/slave.

•Programmable clocks allow versatile rate control.

•Bidirectional data transfer between masters and slaves.

•Multi-master bus (no central master).

•Arbitration between simultaneously transmitting masters without corruption of serial

data on the bus.

•Serial clock synchronization allows devices with different bit rates to communicate via

one serial bus.

•Serial clock synchronization can be used as a handshake mechanism to suspend and

resume serial transfer.

•The I2C-bus can be used for test and diagnostic purposes.

•All I2C-bus controllers support multiple address recognition and a bus monitor mode.

7.19.6 I2S interface

Remark: The LPC436x each contain two I2S-bus interfaces.

The I2S-bus provides a standard communication interface for digital audio applications.

The I2S-bus specification defines a 3-wire serial bus using one data line, one clock line,

and one word select signal. The basic I2S-bus connection has one master, which is

always the master, and one slave. The I2S-bus interface provides a separate transmit and

receive channel, each of which can operate as either a master or a slave.

Product data sheet Rev. 1.3 — 10 January 2020 79 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

7.19.6.1 Features

•The I2S interfaces has separate input/output channels, each of which can operate in

master or slave mode.

•Capable of handling 8-bit, 16-bit, and 32-bit word sizes.

•Mono and stereo audio data supported.

•The sampling frequency can range from 16 kHz to 192 kHz (16, 22.05, 32, 44.1, 48,

96, 192) kHz.

•Support for an audio master clock.

•Configurable word select period in master mode (separately for I2S-bus input and

output).

•Two 8-word FIFO data buffers are provided, one for transmit and one for receive.

•Generates interrupt requests when buffer levels cross a programmable boundary.

•Two DMA requests controlled by programmable buffer levels. The DMA requests are

connected to the GPDMA block.

•Controls include reset, stop and mute options separately for I2S-bus input and I2S-bus

output.

7.19.7 C_CAN

Remark: The LPC436x each contain two C_CAN controllers.

Controller Area Network (CAN) is the definition of a high performance communication

protocol for serial data communication. The C_CAN controller is designed to provide a full

implementation of the CAN protocol according to the CAN Specification Version 2.0B. The

C_CAN controller allows to build powerful local networks with low-cost multiplex wiring by

supporting distributed real-time control with a high level of reliability.

7.19.7.1 Features

•Conforms to protocol version 2.0 parts A and B.

•Supports bit rate of up to 1 Mbit/s.

•Supports 32 Message Objects.

•Each Message Object has its own identifier mask.

•Provides programmable FIFO mode (concatenation of Message Objects).

•Provides maskable interrupts.

•Supports Disabled Automatic Retransmission (DAR) mode for time-triggered CAN

applications.

•Provides programmable loop-back mode for self-test operation.

7.20 Counter/timers and motor control

7.20.1 General purpose 32-bit timers/external event counters

Remark: The LPC436x include four 32-bit timer/counters.

Product data sheet Rev. 1.3 — 10 January 2020 80 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

The timer/counter is designed to count cycles of the system derived clock or an

externally-supplied clock. It can optionally generate interrupts, generate timed DMA

requests, or perform other actions at specified timer values, based on four match

registers. Each timer/counter also includes two capture inputs to trap the timer value when

an input signal transitions, optionally generating an interrupt.

7.20.1.1 Features

•A 32-bit timer/counter with a programmable 32-bit prescaler.

•Counter or timer operation.

•Two 32-bit capture channels per timer, that can take a snapshot of the timer value

when an input signal transitions. A capture event can also generate an interrupt.

•Four 32-bit match registers that allow:

–Continuous operation with optional interrupt generation on match.

–Stop timer on match with optional interrupt generation.

–Reset timer on match with optional interrupt generation.

•Up to four external outputs corresponding to match registers, with the following

capabilities:

–Set LOW on match.

–Set HIGH on match.

–Toggle on match.

–Do nothing on match.

•Up to two match registers can be used to generate timed DMA requests.

7.20.2 Motor control PWM

The motor control PWM is a specialized PWM supporting 3-phase motors and other

combinations. Feedback inputs are provided to automatically sense rotor position and use

that information to ramp speed up or down. An abort input causes the PWM to release all

motor drive outputs immediately . At the same time, the motor control PWM is highly

configurable for other generalized timing, counting, capture, and compare applications.

7.20.3 Quadrature Encoder Interface (QEI)

A quadrature encoder, also known as a 2-channel incremental encoder, converts angular

displacement into two pulse signals. By monitoring both the number of pulses and the

relative phase of the two signals, the user code can track the position, direction of rotation,

and velocity. In addition, a third channel, or index signal, can be used to reset the position

counter. The quadrature encoder interface decodes the digital pulses from a quadrature

encoder wheel to integrate position over time and determine direction of rotation. In

addition, the QEI can capture the velocity of the encoder wheel.

7.20.3.1 Features

•Tracks encoder position.

•Increments/decrements depending on direction.

•Programmable for 2 or 4 position counting.

•Velocity capture using built-in timer.

•Velocity compare function with “less than” interrupt.

Product data sheet Rev. 1.3 — 10 January 2020 81 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

•Uses 32-bit registers for position and velocity.

•Three position compare registers with interrupts.

•Index counter for revolution counting.

•Index compare register with interrupts.

•Can combine index and position interrupts to produce an interrupt for whole and

partial revolution displacement.

•Digital filter with programmable delays for encoder input signals.

•Can accept decoded signal inputs (clk and direction).

7.20.4 Repetitive Interrupt (RI) timer

The repetitive interrupt timer provides a free-running 32-bit counter which is compared to

a selectable value, generating an interrupt when a match occurs. Any bits of the

timer/compare function can be masked such that they do not contribute to the match

detection. The repetitive interrupt timer can be used to create an interrupt that repeats at

predetermined intervals.

7.20.4.1 Features

•32-bit counter. Counter can be free-running or be reset by a generated interrupt.

•32-bit compare value.

•32-bit compare mask. An interrupt is generated when the counter value equals the

compare value, after masking. This mechanism allows for combinations not possible

with a simple compare.

7.20.5 Windowed WatchDog Timer (WWDT)

The purpose of the watchdog is to reset the controller if software fails to periodically

service it within a programmable time window.

7.20.5.1 Features

•Internally resets chip if not periodically reloaded during the programmable time-out

period.

•Optional windowed operation requires reload to occur between a minimum and

maximum time period, both programmable.

•Optional warning interrupt can be generated at a programmable time prior to

watchdog time-out.

•Enabled by software but requires a hardware reset or a watchdog reset/interrupt to be

disabled.

•Incorrect feed sequence causes reset or interrupt if enabled.

•Flag to indicate watchdog reset.

•Programmable 24-bit timer with internal prescaler.

•Selectable time period from (Tcy(WDCLK)  256  4) to (Tcy(WDCLK)  224  4) in

multiples of Tcy(WDCLK)  4.

•The Watchdog Clock (WDCLK) uses the IRC as the clock source.

Product data sheet Rev. 1.3 — 10 January 2020 82 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

7.21 Analog peripherals

7.21.1 Analog-to-Digital Converter (ADC0/1)

Remark: The LPC436x contain two 10-bit ADCs.

7.21.1.1 Features

•10-bit successive approximation analog to digital converter.

•Input multiplexing among 8 pins.

•Power-down mode.

•Measurement range 0 to VDDA.

•Sampling frequency up to 400 kSamples/s.

•Burst conversion mode for single or multiple inputs.

•Optional conversion on transition on ADCTRIG0 or ADCTRIG1 pins, combined timer

outputs 8 or 15, or the PWM output MCOA2.

•Individual result registers for each A/D channel to reduce interrupt overhead.

•DMA support.

7.21.2 Digital-to-Analog Converter (DAC)

7.21.2.1 Features

•10-bit resolution

•Monotonic by design (resistor string architecture)

•Controllable conversion speed

•Low power consumption

7.22 Peripherals in the RTC power domain

7.22.1 RTC

The Real Time Clock (RTC) is a set of counters for measuring time when system power is

on, and optionally when it is off. It uses little power when the CPU does not access its

registers, especially in the reduced power modes. A separate 32 kHz oscillator clocks the

RTC. The oscillator produces a 1 Hz internal time reference and is powered by its own

power supply pin, VBAT.

7.22.1.1 Features

•Measures the passage of time to maintain a calendar and clock. Provides seconds,

minutes, hours, day of month, month, year, day of week, and day of year.

•Ultra-low power design to support battery powered systems. Uses power from the

CPU power supply when it is present.

•Dedicated battery power supply pin.

•RTC power supply is isolated from the rest of the chip.

•Calibration counter allows adjustment to better than 1 sec/day with 1 sec resolution.

•Periodic interrupts can be generated from increments of any field of the time registers.

Product data sheet Rev. 1.3 — 10 January 2020 83 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

•Alarm interrupt can be generated for a specific date/time.

7.22.1.2 Event monitor/recorder

The event monitor/recorder allows recording and creating a time stamp of events related

to the WAKEUP pins. Sensors report changes to the state of the WAKEUP pins, and the

event monitor/recorder stores records of such events. The event recorder can be

The event monitor/recorder can monitor the integrity of the device and record any

tampering events.

Features

•Supports three digital event inputs in the VBAT power domain.

•An event is defined as a level change at the digital event inputs.

•For each event channel, two timestamps mark the first and the last occurrence of an

event. Each channel also has a dedicated counter tracking the total number of events.

Timestamp values are taken from the RTC.

•Runs in VBAT power domain, independent of system power supply. The

event/recorder/monitor can therefore operate in Deep power-down mode.

•Low power consumption.

•Interrupt available if system is running.

•A qualified event can be used as a wake-up trigger.

•State of event interrupts accessible by software through GPIO.

7.22.2 Alarm timer

The alarm timer is a 16-bit timer and counts down at 1 kHz from a preset value generating

alarms in intervals of up to 1 min. The counter triggers a status bit when it reaches 0x00

and asserts an interrupt if enabled.

The alarm timer is part of the RTC power domain and can be battery powered.

7.23 System control

7.23.1 Configuration registers (CREG)

The following settings are controlled in the configuration register block:

•BOD trip settings

•Oscillator output

•DMA-to-peripheral muxing

•Ethernet mode

•Memory mapping

•Timer/USART inputs

•Enabling the USB controllers

In addition, the CREG block contains the part identification and part configuration

information.

Product data sheet Rev. 1.3 — 10 January 2020 84 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

7.23.2 System Control Unit (SCU)

The system control unit determines the function and electrical mode of the digital pins. By

default function 0 is selected for all pins with pull-up enabled. For pins that support a

digital and analog function, the ADC function select registers in the SCU enable the

analog function.

A separate set of analog I/Os for the ADCs and the DAC as well as most USB pins are

located on separate pads and are not controlled through the SCU.

In addition, the clock delay register for the SDRAM EMC_CLK pins and the registers that

select the pin interrupts are located in the SCU.

7.23.3 Clock Generation Unit (CGU)

The Clock Generator Unit (CGU) generates several base clocks. The base clocks can be

unrelated in frequency and phase and can have different clock sources within the CGU.

One CGU base clock is routed to the CLKOUT pins. The base clock that generates the

CPU clock is referred to as CCLK.

Multiple branch clocks are derived from each base clock. The branch clocks offer flexible

control for power-management purposes. All branch clocks are outputs of one of two

Clock Control Units (CCUs) and can be controlled independently. Branch clocks derived

from the same base clock are synchronous in frequency and phase.

7.23.4 Internal RC oscillator (IRC)

The IRC is used as the clock source for the WWDT and/or as the clock that drives the

PLLs and the CPU. The nominal IRC frequency is 12 MHz. The IRC is trimmed to 1.5 %

accuracy for Tamb = 0 °C to 85 °C and 3% accuracy for Tamb = -40 °C to 0 °C and Tamb =

85 °C to 105 °C.

Upon power-up or any chip reset, the LPC436x use the IRC as the clock source. The boot

loader then configures the PLL1 to provide a 96 MHz clock for the core and PLL0USB or

PLL0AUDIO as needed if an external boot source is selected.

7.23.5 PLL0USB (for USB0)

PLL0 is a dedicated PLL for the USB0 High-speed controller.

PLL0 accepts an input clock frequency from an external oscillator in the range of 14 kHz

to 25 MHz. The input frequency is multiplied up to a high frequency with a Current

Controlled Oscillator (CCO). The CCO operates in the range of 4.3 MHz to 550 MHz.

7.23.6 PLL0AUDIO (for audio)

The audio PLL PLL0AUDIO is a general purpose PLL with a very small step size. This

PLL accepts an input clock frequency derived from an external oscillator or internal IRC.

The input frequency is multiplied up to a high frequency with a Current Controlled

Oscillator (CCO). A sigma-delta converter modulates the PLL divider ratios to obtain the

desired output frequency. The output frequency can be set as a multiple of the sampling

frequency fs to 32fs, 64fs, 128  fs, 256  fs, 384  fs, 512  fs and the sampling

frequency fs can range from 16 kHz to 192 kHz (16, 22.05, 32, 44.1, 48, 96,192) kHz.

Many other frequencies are possible as well using the integrated fractional divider.

Product data sheet Rev. 1.3 — 10 January 2020 85 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

7.23.7 System PLL1

The PLL1 accepts an input clock frequency from an external oscillator in the range of

1 MHz to 25 MHz. The input frequency is multiplied up to a high frequency with a Current

Controlled Oscillator (CCO). The multiplier can be an integer value from 1 to 32. The CCO

operates in the range of 156 MHz to 320 MHz. This range is possible through an

additional divider in the loop to keep the CCO within its frequency range while the PLL is

providing the desired output frequency. The output divider can be set to divide by 2, 4, 8,

or 16 to produce the output clock. Since the minimum output divider value is 2, it is

insured that the PLL output has a 50 % duty cycle. The PLL is turned off and bypassed

following a chip reset. After reset, software can enable the PLL. The program must

configure and activate the PLL, wait for the PLL to lock, and then connect to the PLL as a

clock source. The PLL settling time is 100 s.

7.23.8 Reset Generation Unit (RGU)

The RGU allows generation of independent reset signals for individual blocks and

peripherals on the LPC436x.

7.23.9 Power Management Controller (PMC)

The PMC controls the power to the cores, peripherals, and memories.

The LPC436x support the following power modes in order from highest to lowest power

consumption:

1. Active mode

2. Sleep mode

3. Power-down modes:

a. Deep-sleep mode

b. Power-down mode

c. Deep power-down mode

Active mode and sleep mode apply to the state of the core. In a dual-core system, either

core can be in active or sleep mode independently of the other core.

If the core is in Active mode, it is fully operational and can access peripherals and

memories as configured by software. If the core is in Sleep mode, it receives no clocks,

but peripherals and memories remain running.

Either core can enter sleep mode from active mode independently of the other core and

while the other core remains in active mode or is in sleep mode.

Power-down modes apply to the entire system. In the Power-down modes, both cores and

all peripherals except for peripherals in the always-on power domain are shut down.

Memories can remain powered for retaining memory contents as defined by the individual

power-down mode.

Either core in active mode can put the part into one of the three power down modes if the

core is enabled to do so. If both cores are enabled for putting the system into power-down,

then the system enters power-down only once both cores have received a WFI or WFE

instruction.

Product data sheet Rev. 1.3 — 10 January 2020 86 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

Wake-up from sleep mode is caused by an interrupt or event in the core’s NVIC. The

interrupt is captured in the NVIC and an event is captured in the Event router. Both cores

can wake up from sleep mode independently of each other.

Wake-up from the Power-down modes, Deep-sleep, Power-down, and Deep power-down,

is caused by an event on the WAKEUP pins or an event from the RTC or alarm timer.

When waking up from Deep power-down mode, the part resets and attempts to boot.

7.23.10 Power control

The LPC436x feature several independent power domains to control power to the core

and the peripherals (see Figure 8). The RTC and its associated peripherals (the alarm

timer, the CREG block, the OTP controller, the back-up registers, and the event router)

are located in the RTC power-domain. The main regulator or a battery supply can power

the RTC. A power selector switch ensures that the RTC block is always powered on.

Fig 8. Power domains

REAL-TIME CLOCK

BACKUP REGISTERS

RESET/WAKE-UP

CONTROL

REGULATOR

32 kHz

OSCILLATOR

ALWAYS-ON/RTC POWER DOMAIN

MAIN POWER DOMAIN

RTCX1

VBAT

VDDREG

RTCX2

VDDIO

VSS

to memories,

peripherals,

oscillators,

PLLs

to cores

to I/O pads

ADC

DAC

OTP

ADC POWER DOMAIN

OTP POWER DOMAIN

USB0 POWER DOMAIN

VDDA

VSSA

VPP

USB0

USB0_VDDA3V_DRIVER

USB0_VDDA3V3

LPC43xx

ULTRA LOW-POWER

REGULATOR

ALARM

RESET

WAKEUP0/1/2/3

to RTC

domain

peripherals

002aag378

to RTC I/O

pads (Vps)

Product data sheet Rev. 1.3 — 10 January 2020 87 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

7.23.11 Code security (Code Read Protection - CRP)

CRP enables different levels of security so that access to the on-chip flash and use of the

JTAG and ISP can be restricted. CRP is invoked by programming a specific pattern into a

dedicated flash location. IAP commands are not affected by CRP.

There are three levels of the Code Read Protection:

•In level CRP1, access to the chip via the JTAG is disabled. Partial flash updates are

allowed (excluding flash sector 0) using a limited set of the ISP commands. This level

is useful when CRP is required and flash field updates are needed. CRP1 does

prevent the user code from erasing all sectors.

•In level CRP2, access to the chip via the JTAG is disabled. Only a full flash erase and

update using a reduced set of the ISP commands is allowed.

•In level CRP3, any access to the chip via the JTAG pins or the ISP is disabled. This

mode also disables the ISP override using P2_7 pin. If necessary, the application

code must provide a flash update mechanism using the IAP calls or using the

reinvoke ISP command to enable flash update via USART0. See Table 5

7.24 Serial Wire Debug/JTAG

Debug and trace functions are integrated into the ARM Cortex-M4. Serial wire debug and

trace functions are supported in addition to a standard JTAG debug and parallel trace

functions. The ARM Cortex-M4 is configured to support up to eight breakpoints and four

watch points.

Remark: Serial Wire Debug is supported for the ARM Cortex-M4 only,

The ARM Cortex-M0 coprocessors support JTAG debug. A standard ARM

Cortex-compliant debugger can debug the ARM Cortex-M4 and the ARM Cortex-M0

cores separately or both cores simultaneously.

Remark: In order to debug the ARM Cortex-M0, release the M0 reset by software in the

RGU block.

CAUTION

If level three Code Read Protection (CRP3) is selected, no future factory testing can be

performed on the device.

Product data sheet Rev. 1.3 — 10 January 2020 88 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

Fig 9. Dual-core debug configuration

002aah448

ARM Cortex-M0 ARM Cortex-M4

TCK

DBGEN = HIGH

TMS

TRST

TDI TDO TDO

TDO

DBGEN

RESET = HIGH

RESET

TCK

TMS

TRST

TDI

TCK

TMS

TRST

TDI

JTAG ID = 0x0BA0 1477 JTAG ID = 0x4BA0 0477

LPC43xx

Product data sheet Rev. 1.3 — 10 January 2020 89 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

8. Limiting values

[1] The following applies to the limiting values:

a) Absolute maximum ratings state the extreme limits that the product can withstand without leading to irrecoverable failure. Failure

includes the loss of reliability and shorter lifetime of the device. Conditions for functional operation of the part are shown in Table 11

“Static characteristics”.

b) This product includes circuitry designed for the protection of its internal devices from the damaging effects of excessive static

charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated maximum.

c) Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to VSS unless

otherwise noted.

[2] Including voltage on outputs in 3-state mode.

[3] Dependent on package type.

[4] Human body model: equivalent to discharging a 100 pF capacitor through a 1.5 k series resistor.

Table 7. Limiting values

In accordance with the Absolute Maximum Rating System (IEC 60134).[1]

Symbol Parameter Conditions Min Max Unit

VDD(REG)(3V3) regulator supply voltage

(3.3 V)

on pin VDDREG 0.5 3.6 V

VDD(IO) input/output supply

voltage

on pin VDDIO 0.5 3.6 V

VDDA(3V3) analog supply voltage

(3.3 V)

on pin VDDA 0.5 3.6 V

VBAT battery supply voltage on pin VBAT 0.5 3.6 V

Vprog(pf) polyfuse programming

voltage

on pin VPP 0.5 3.6 V

VIinput voltage when VDD(IO)  2.4 V

5 V tolerant digital I/O pins

[2] 0.5 5.5 V

ADC/DAC pins and digital I/O

pins configured for an analog

function

0.5 VDDA(3V3) V

USB0 pins USB0_DP;

USB0_DM;USB0_VBUS

0.3 5.25 V

USB0 pins USB0_ID;

USB0_RREF

0.3 3.6 V

USB1 pins USB1_DP and

USB1_DM

0.3 5.25 V

IDD supply current per supply pin - 100 mA

ISS ground current per ground pin - 100 mA

Ilatch I/O latch-up current (0.5VDD(IO)) < VI < (1.5VDD(IO));

Tj < 125 C

- 100 mA

Tstg storage temperature [3] 65 +150 C

Ptot(pack) total power dissipation

(per package)

based on package heat transfer,

not device power consumption

- 1.5 W

VESD electrostatic discharge

voltage

human body model; all pins [4] - 2000 V

Product data sheet Rev. 1.3 — 10 January 2020 90 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

9. Thermal characteristics

The average chip junction temperature, Tj (C), can be calculated using the following

equation:

(1)

•Tamb = ambient temperature (C),

•Rth(j-a) = the package junction-to-ambient thermal resistance (C/W)

•PD = sum of internal and I/O power dissipation

The internal power dissipation is the product of IDD and VDD. The I/O power dissipation of

the I/O pins is often small and many times can be negligible. However it can be significant

in some applications.

Table 8. Thermal characteristics

Symbol Parameter Conditions Min Typ Max Unit

Tj(max) maximum junction

temperature

- - - 125 C

Table 9. Thermal resistance (LQFP packages)

Symbol Parameter Conditions Thermal resistance in C/W

±15 %

LQFP144 LQFP208

Rth(j-a) thermal resistance from

junction to ambient

JEDEC (4.5 in  4 in); still

air

38 31

Single-layer (4.5 in  3 in);

still air

50 39

Rth(j-c) thermal resistance from

junction to case

-1110

Table 10. Thermal resistance value (BGA packages)

Symbol Parameter Conditions Thermal resistance in C/W ±15 %

LBGA256 TFBGA100

Rth(j-a) thermal resistance from

junction to ambient

JEDEC (4.5 in  4 in);

still air

29 46

8-layer (4.5 in  3 in);

still air

24 37

Rth(j-c) thermal resistance from

junction to case

-1411

jTamb PDRth j a–

+=

Product data sheet Rev. 1.3 — 10 January 2020 91 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

10. Static characteristics

Table 11. Static characteristics

Tamb = 40 C to +105 C, unless otherwise specified.

Symbol Parameter Conditions Min Typ[1] Max Unit

Supply pins

VDD(IO) input/output supply

voltage

[17] 2.4 - 3.6 V

VDD(REG)(3V3) regulator supply voltage

(3.3 V)

[2] 2.4 - 3.6 V

VDDA(3V3) analog supply voltage

(3.3 V)

on pin VDDA 2.4 - 3.6 V

on pins

USB0_VDDA3V3_

DRIVER and

USB0_VDDA3V3

3.0 3.3 3.6 V

VBAT battery supply voltage [2] 2.4 - 3.6 V

Vprog(pf) polyfuse programming

voltage

on pin VPP (for OTP) [3] 2.7 - 3.6 V

Iprog(pf) polyfuse programming

current

on pin VPP; OTP

programming time 

1.6 ms

- - 30 mA

IDD(REG)(3V3) regulator supply current

(3.3 V)

Active mode; ARM

Cortex-M0 core in reset;

code

while(1){}

executed from RAM; all

peripherals disabled;

PLL1 enabled

CCLK = 12 MHz [4] -10-mA

CCLK = 60 MHz [4] 28 - mA

CCLK = 120 MHz [4] -51-mA

CCLK = 180 MHz [4] -74-mA

CCLK = 204 MHz [4] -83-mA

IDD(REG)(3V3) regulator supply current

(3.3 V)

after WFE/WFI instruction

executed from RAM; all

peripherals disabled;

ARM Cortex-M0 core in

reset

sleep mode [4][5] - 8.8 - mA

deep-sleep mode [4] - 145 - A

power-down mode [4] -23-A

deep power-down

mode

[4][6] - 0.05 - A

deep power-down

mode; VBAT floating

[4] - 3.0 - A

IBAT battery supply current VBAT = 3.0 V;

VDD(REG)(3V3) = 3.3 V

[7] - 0.1 nA

Product data sheet Rev. 1.3 — 10 January 2020 92 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

IBAT battery supply current VDD(REG)(3V3) = 3.3 V;

VBAT = 3.6 V

deep-sleep mode

[8]

- 1.5 - A

power-down mode [8] - 1.5 - A

deep power-down

mode

[8]

- 1.5 - A

IBAT battery supply current Deep power-down mode;

RTC running;

VDD(REG) = VDDA =

VDDIO = 0 V; - 3.0 - A

VDD(REG)(3V3) =

VBAT = 3.3 V

1.5 - A

IDD(IO) I/O supply current deep sleep mode - < 0.1 - A

power-down mode - < 0.1 - A

deep power-down mode - < 0.1 - A

IDDA Analog supply current on pin VDDA;

deep sleep mode

[10] - 0.4 -

A

power-down mode [10] - 0.4 - A

deep power-down

mode

[10] - 0.007 -

A

RESET pin

VIH HIGH-level input

voltage

[9] 0.8  (Vps 

0.35)

- 5.5 V

VIL LOW-level input voltage [9] 0.5 - 0.3  (Vps 

0.1)

Vhys hysteresis voltage [9] 0.05  (Vps

 0.35)

--V

Standard I/O pins - normal drive strength

CIinput capacitance - - 2 pF

ILL LOW-level leakage

current

VI = 0 V; on-chip pull-up

resistor disabled

-3-nA

ILH HIGH-level leakage

current

VI = VDD(IO); on-chip

pull-down resistor

disabled

-3-nA

VI = 5 V; Tamb = 25 °C - 0.5 - nA

VI = 5 V; Tamb = 105 °C - 40 - nA

IOZ OFF-state output

current

VO = 0 V to VDD(IO);

on-chip pull-up/down

resistors disabled;

absolute value

-3-nA

VIinput voltage pin configured to provide

a digital function;

VDD(IO)  2.4 V

0 - 5.5 V

VDD(IO) = 0 V 0 - 3.6 V

VOoutput voltage output active 0 - VDD(IO) V

Table 11. Static characteristics …continued

Tamb = 40 C to +105 C, unless otherwise specified.

Symbol Parameter Conditions Min Typ[1] Max Unit

Product data sheet Rev. 1.3 — 10 January 2020 93 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

VIH HIGH-level input

voltage

0.7 

VDD(IO)

- 5.5 V

VIL LOW-level input voltage 0.5 - 0.3 

VDD(IO)

Vhys hysteresis voltage 0.1 

VDD(IO)

--V

VOH HIGH-level output

voltage

IOH = 6 mA VDD(IO) 

0.4

--V

VOL LOW-level output

voltage

IOL = 6 mA - - 0.4 V

IOH HIGH-level output

current

VOH = VDD(IO)  0.4 V 6- - mA

IOL LOW-level output

current

VOL = 0.4 V 6 - - mA

IOHS HIGH-level short-circuit

output current

drive HIGH; connected to

ground

[11] - - 86.5 mA

IOLS LOW-level short-circuit

output current

drive LOW; connected to

VDD(IO)

[11] - - 76.5 mA

Ipd pull-down current VI = 5 V [13]

[14]

[15]

-93-A

Ipu pull-up current VI = 0 V [13]

[14]

[15]

-62 - A

VDD(IO) < VI  5 V - 10 - A

Rsseries resistance on I/O pins with analog

function; analog function

enabled

200 

I/O pins - high drive strength

CIinput capacitance - - 5.2 pF

ILL LOW-level leakage

current

VI = 0 V; on-chip pull-up

resistor disabled

-3-nA

IOZ OFF-state output

current

VO = 0 V to VDD(IO);

on-chip pull-up/down

resistors disabled;

absolute value

-3-nA

VIinput voltage pin configured to provide

a digital function;

VDD(IO)  2.4 V 0 - 5.5 V

VDD(IO) = 0 V 0 - 3.6 V

VOoutput voltage output active 0 - VDD(IO) V

VIH HIGH-level input

voltage

0.7 

VDD(IO)

- 5.5 V

VIL LOW-level input voltage 0.5 - 0.3 

VDD(IO)

Table 11. Static characteristics …continued

Tamb = 40 C to +105 C, unless otherwise specified.

Symbol Parameter Conditions Min Typ[1] Max Unit

Product data sheet Rev. 1.3 — 10 January 2020 94 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

Vhys hysteresis voltage 0.1 

VDD(IO)

--V

Ipd pull-down current VI = VDD(IO) [13]

[14]

[15]

-62-A

Ipu pull-up current VI = 0 V [13]

[14]

[15]

-62 - A

VDD(IO) < VI  5 V - 10 - A

I/O pins - high drive strength: standard drive mode

ILH HIGH-level leakage

current

VI = VDD(IO); on-chip

pull-down resistor

disabled

-3-nA

VI = 5 V; Tamb = 25 °C - 0.6 - nA

VI = 5 V; Tamb = 105 °C - 65 - nA

IOH HIGH-level output

current

VOH = VDD(IO)  0.4 V 4- - mA

IOL LOW-level output

current

VOL = 0.4 V 4 - - mA

IOHS HIGH-level short-circuit

output current

drive HIGH; connected to

ground

[11] - - 32 mA

IOLS LOW-level short-circuit

output current

drive LOW; connected to

VDD(IO)

[11] - - 32 mA

I/O pins - high drive strength: medium drive mode

ILH HIGH-level leakage

current

VI = VDD(IO); on-chip

pull-down resistor

disabled

-3-nA

VI = 5 V; Tamb = 25 °C - 0.7 - nA

VI = 5 V; Tamb = 105 °C - 70 - nA

IOH HIGH-level output

current

VOH = VDD(IO)  0.4 V 8- - mA

IOL LOW-level output

current

VOL = 0.4 V 8 - - mA

IOHS HIGH-level short-circuit

output current

drive HIGH; connected to

ground

[11] - - 65 mA

IOLS LOW-level short-circuit

output current

drive LOW; connected to

VDD(IO)

[11] - - 63 mA

I/O pins - high drive strength: high drive mode

ILH HIGH-level leakage

current

VI = VDD(IO); on-chip

pull-down resistor

disabled

-3-nA

VI = 5 V; Tamb = 25 °C - 0.6 - nA

VI = 5 V; Tamb = 105 °C - 63 - nA

IOH HIGH-level output

current

VOH = VDD(IO)  0.4 V 14 - - mA

Table 11. Static characteristics …continued

Tamb = 40 C to +105 C, unless otherwise specified.

Symbol Parameter Conditions Min Typ[1] Max Unit

Product data sheet Rev. 1.3 — 10 January 2020 95 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

IOL LOW-level output

current

VOL = 0.4 V 14 - - mA

IOHS HIGH-level short-circuit

output current

drive HIGH; connected to

ground

[11] --113mA

IOLS LOW-level short-circuit

output current

drive LOW; connected to

VDD(IO)

[11] --110mA

I/O pins - high drive strength: ultra-high drive mode

ILH HIGH-level leakage

current

VI = VDD(IO); on-chip

pull-down resistor

disabled

-3-nA

VI = 5 V; Tamb = 25 °C - 0.6 - nA

VI = 5 V; Tamb = 105 °C - 63 - nA

IOH HIGH-level output

current

VOH = VDD(IO)  0.4 V 20 - - mA

IOL LOW-level output

current

VOL = 0.4 V 20 - - mA

IOHS HIGH-level short-circuit

output current

drive HIGH; connected to

ground

[11] - - 165 mA

IOLS LOW-level short-circuit

output current

drive LOW; connected to

VDD(IO)

[11] - - 156 mA

I/O pins - high-speed

CIinput capacitance - - 2 pF

ILL LOW-level leakage

current

VI = 0 V; on-chip pull-up

resistor disabled

-3-nA

ILH HIGH-level leakage

current

VI = VDD(IO); on-chip

pull-down resistor

disabled

-3-nA

VI = 5 V; Tamb = 25 °C - 0.5 - nA

VI = 5 V; Tamb = 105 °C - 40 - nA

IOZ OFF-state output

current

VO = 0 V to VDD(IO);

on-chip pull-up/down

resistors disabled;

absolute value

-3-nA

VIinput voltage pin configured to provide

a digital function;

VDD(IO)  2.4 V 0 - 5.5 V

VDD(IO) = 0 V 0 - 3.6 V

VOoutput voltage output active 0 - VDD(IO) V

VIH HIGH-level input

voltage

0.7 

VDD(IO)

- 5.5 V

VIL LOW-level input voltage 0.5 - 0.3 

VDD(IO)

Vhys hysteresis voltage 0.1 

VDD(IO)

--V

Table 11. Static characteristics …continued

Tamb = 40 C to +105 C, unless otherwise specified.

Symbol Parameter Conditions Min Typ[1] Max Unit

Product data sheet Rev. 1.3 — 10 January 2020 96 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

VOH HIGH-level output

voltage

IOH = 8 mA VDD(IO) 

0.4

--V

VOL LOW-level output

voltage

IOL = 8 mA - - 0.4 V

IOH HIGH-level output

current

VOH = VDD(IO)  0.4 V 8- - mA

IOL LOW-level output

current

VOL = 0.4 V 8 - - mA

IOHS HIGH-level short-circuit

output current

drive HIGH; connected to

ground

[11] - - 86 mA

IOLS LOW-level short-circuit

output current

drive LOW; connected to

VDD(IO)

[11] - - 76 mA

Ipd pull-down current VI = VDD(IO) [13]

[14]

[15]

-62-A

Ipu pull-up current VI = 0 V [13]

[14]

[15]

-62 - A

VDD(IO) < VI  5 V - 0 - A

Open-drain I2C0-bus pins

VIH HIGH-level input

voltage

0.7 

VDD(IO)

--V

VIL LOW-level input voltage 0.5 0.14 0.3 

VDD(IO)

Vhys hysteresis voltage 0.1 

VDD(IO)

--V

VOL LOW-level output

voltage

IOLS = 3 mA - - 0.4 V

ILI input leakage current VI = VDD(IO) [12] - 4.5 - A

VI = 5 V - - 10 A

Oscillator pins

Vi(XTAL1) input voltage on pin

XTAL1

0.5 - 1.2 V

Vo(XTAL2) output voltage on pin

XTAL2

0.5 - 1.2 V

Cio input/output

capacitance

[16] - - 0.8 pF

USB0 pins[17]

VIinput voltage on pins USB0_DP;

USB0_DM; USB0_VBUS

VDD(IO)  2.4 V 0 - 5.25 V

VDD(IO) = 0 V 0 - 3.6 V

Rpd pull-down resistance on pin USB0_VBUS 48 64 80 k

Table 11. Static characteristics …continued

Tamb = 40 C to +105 C, unless otherwise specified.

Symbol Parameter Conditions Min Typ[1] Max Unit

Product data sheet Rev. 1.3 — 10 January 2020 97 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

[1] Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply voltages.

[2] The recommended operating condition for the battery supply is VDD(REG)(3V3) > VBAT + 0.2 V. Special conditions for VDD(REG)(3V3) apply

when writing to the flash and EEPROM. See Table 16 and Table 15.

[3] Pin VPP should either be not connected (when OTP does not need to be programmed) or tied to pins VDDIO and VDDREG to ensure

the same ramp-up time for both supply voltages.

[4] VDD(REG)(3V3) = 3.3 V; VDD(IO) = 3.3 V; Tamb = 25 C.

[5] PLL1 disabled; IRC running; CCLK = 12 MHz.

[6] VBAT = 3.6 V.

[7] Tamb = -40 C to +105 C; VDD(IO) = VDDA = 3.6 V; over entire frequency range CCLK = 12 MHz to 204 MHz; in active mode, sleep

mode; deep-sleep mode, power-down mode, and deep power-down mode.

[8] On pin VBAT; Tamb = 25 C.

[9] Vps corresponds to the output of the power switch (see Figure 8) which is determined by the greater of VBAT and VDD(Reg)(3V3).

[10] VDDA(3V3) = 3.3 V; Tamb = 25 C.

[11] Allowed as long as the current limit does not exceed the maximum current allowed by the device.

[12] To VSS.

[13] The values specified are simulated and absolute values.

[14] The weak pull-up resistor is connected to the VDD(IO) rail and pulls up the I/O pin to the VDD(IO) level.

[15] The input cell disables the weak pull-up resistor when the applied input voltage exceeds VDD(IO).

VIC common-mode input

voltage

high-speed mode 50 200 500 mV

full-speed/low-speed

mode

800 - 2500 mV

chirp mode 50 - 600 mV

Vi(dif) differential input voltage 100 400 1100 mV

USB1 pins (USB1_DP/USB1_DM)[17]

IOZ OFF-state output

current

0 V < VI < 3.3 V [17] --10 A

VBUS bus supply voltage [18] - - 5.25 V

VDI differential input

sensitivity voltage

(D+)  (D)0.2 - - V

VCM differential common

mode voltage range

includes VDI range 0.8 - 2.5 V

Vth(rs)se single-ended receiver

switching threshold

voltage

0.8 - 2.0 V

VOL LOW-level output

voltage for

low-/full-speed

RL of 1.5 k to 3.6 V - - 0.18 V

VOH HIGH-level output

voltage (driven) for

low-/full-speed

RL of 15 k to GND 2.8 - 3.5 V

Ctrans transceiver capacitance pin to GND - - 20 pF

ZDRV driver output

impedance for driver

which is not high-speed

capable

with 33  series resistor;

steady state drive

[19] 36 - 44.1 

Table 11. Static characteristics …continued

Tamb = 40 C to +105 C, unless otherwise specified.

Symbol Parameter Conditions Min Typ[1] Max Unit

Product data sheet Rev. 1.3 — 10 January 2020 98 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

[16] The parameter value specified is a simulated value excluding bond capacitance.

[17] For USB operation 3.0 V  VDD((IO)  3.6 V. Guaranteed by design.

[18] VDD(IO) present.

[19] Includes external resistors of 33   1 % on D+ and D.

10.1 Power consumption

Conditions: Tamb = 25 C; executing code while (1){} from SRAM; M0 core in reset; system PLL

enabled; IRC enabled; all peripherals disabled; all peripheral clocks disabled.

Fig 10. Typical supply current versus regulator supply voltage VDD(REEG)(3V3) in active

mode

Conditions: VDD(REG)(3V3) = 3.3 V; executing code while (1){} from SRAM; M0 core in reset; system

PLL enabled; IRC enabled; all peripherals disabled; all peripheral clocks disabled.

Fig 11. Typical supply current versus temperature in active mode

aaa-013450

2.2 2.4 2.6 2.8 3 3.2 3.4 3.6

100

VDD(REG)(3V3) (V)

DD(REG)(3V3)

IDD(REG)(3V3)

(mA)

12 MHz

60 MHz

120 MHz

180 MHz

204 MHz

aaa-013449

-40 -20 0 20 40 60 80 100 120

100

temperature (°C)

DD(REG)(3V3)

IDD(REG)(3V3)

(mA)

12 MHz

60 MHz

120 MHz

180 MHz

204 MHz

Product data sheet Rev. 1.3 — 10 January 2020 99 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

Conditions: active mode entered executing code while (1){} from SRAM; M0 core in reset;

VDD(REG)(3V3) = 3.3 V; system PLL enabled; IRC enabled; all peripherals disabled; all peripheral

clocks disabled.

Fig 12. Typical supply current versus core frequency in active mode; code executed from

SRAM

Conditions: VDD(REG)(3V3) = 3.3 V; internal pull-up resistors disabled; M0 core in reset; system PLL

disabled; IRC enabled; all peripherals disabled; all peripheral clocks disabled. CCLK = 12 MHz.

Fig 13. Typical supply current versus temperature in sleep mode

aaa-013452

12 36 60 84 108 132 156 180 20

100

frequency (MHz)

DD(REG)(3V3)

IDD(REG)(3V3)

(mA)

+105 C

+105 °C

+90 C

+90 °C

+25 C

+25 °C

0 C

0 °C

-40 C

-40 °C

aaa-013047

-40 -20 0 20 40 60 80 100 120

temperature (°C)

DD(REG)(3V3)

IDD(REG)(3V3)

(mA)

Product data sheet Rev. 1.3 — 10 January 2020 100 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V. Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V.

Fig 14. Typical supply current versus temperature in

Deep-sleep mode

Fig 15. Typical supply current versus temperature in

Power-down mode

002aah410

-40 0 40 80 120

0.4

0.8

1.2

1.6

temperature (°C)

(μA)

IDD(REG)(3V3)

(mA)

002aah412

-40 0 40 80 120

120

180

240

300

temperature (°C)

(μA)

IDD(REG)(3V3)

(μA)

Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V. VBAT =

VDD(REG)(3V3) + 0.4 V.

Conditions: VBAT = 3.6 V. VDD(REG)(3V3) not present.

Fig 16. Typical supply current versus temperature in

Deep power-down mode

Fig 17. Typical battery supply current versus

temperature

002aah424

-40 -20 0 20 40 60 80 100 120

temperature (°C)

(μA)

IBAT

IDD(REG)(3V3)/IBAT

(μA)

IBAT

IDD(REG)(3V3)

002aah415

-40 -20 0 20 40 60 80 100 120

temperature (°C)

IBAT

(μA)

Product data sheet Rev. 1.3 — 10 January 2020 101 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

10.2 Peripheral power consumption

The typical power consumption at T = 25 C for each individual peripheral is measured as

follows:

1. Enable all branch clocks and measure the current IDD(REG)(3V3).

2. Disable the branch clock to the peripheral to be measured and keep all other branch

clocks enabled.

3. Calculate the difference between measurement 1 and 2. The result is the peripheral

power consumption.

Conditions: VDD(REG)(3V3) = 3.0 V; VBAT = 2.6 V to 3.6 V; CCLK = 12 MHz.

Remark: The recommended operating condition for the battery supply is

VDD(REG)(3V3) > VBAT + 0.2 V.

Fig 18. Typical battery supply current in Active mode

002aah379

-0.4 -0.2 0 0.2 0.4 0.6

100

BAT

- V

DD(REG)(3V3)

(V)

BAT

(μA)

Table 12. Peripheral power consumption

Peripheral Branch clock IDD(REG)(3V3) in mA

Branch clock

frequency = 48 MHz

Branch clock

frequency = 96 MHz

M0 subsystem core CLK_PERIPH_CORE 2.4 4.8

M0 coprocessor CLK_M4_M0APP 3.3 6.6

I2C1 CLK_APB3_I2C1 0.01 0.01

I2C0 CLK_APB1_I2C0 < 0.01 0.02

DAC CLK_APB3_DAC 0.01 0.02

ADC0 CLK_APB3_ADC0 0.07 0.07

ADC1 CLK_APB3_ADC1 0.07 0.07

CAN0 CLK_APB3_CAN0 0.17 0.17

CAN1 CLK_APB1_CAN1 0.16 0.15

MOTOCON CLK_APB1_MOTOCON 0.04 0.04

I2S CLK_APB1_I2S 0.09 0.08

Product data sheet Rev. 1.3 — 10 January 2020 102 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

SPIFI CLK_SPIFI,

CLK_M4_SPIFI

1.14 2.29

GPIO CLK_M4_GPIO 0.72 1.43

LCD CLK_M4_LCD 0.91 1.82

ETHERNET CLK_M4_ETHERNET 1.06 2.15

UART0 CLK_M4_UART0,

CLK_APB0_UART0

0.24 0.43

UART1 CLK_M4_UART1,

CLK_APB0_UART1

0.24 0.43

UART2 CLK_M4_UART2,

CLK_APB2_UART2

0.26 0.5

UART3 CLK_M4_USART3,

CLK_APB2_UART3

0.27 0.45

TIMER0 CLK_M4_TIMER0 0.08 0.15

TIMER1 CLK_M4_TIMER1 0.09 0.15

TIMER2 CLK_M4_TIMER2 0.1 0.19

TIMER3 CLK_M4_TIMER3 0.08 0.16

SDIO CLK_M4_SDIO,

CLK_SDIO

0.66 1.17

SCTimer/PWM CLK_M4_SCT 0.66 1.3

SSP0 CLK_M4_SSP0,

CLK_APB0_SSP0

0.13 0.23

SSP1 CLK_M4_SSP1,

CLK_APB2_SSP1

0.14 0.27

DMA CLK_M4_DMA 1.81 3.61

WWDT CLK_M4_WWDT 0.03 0.09

QEI CLK_M4_QEI 0.28 0.55

USB0 CLK_M4_USB0,

CLK_USB0

1.9 3.9

USB1 CLK_M4_USB1,

CLK_USB1

3.02 5.69

RITIMER CLK_M4_RITIMER 0.05 0.1

EMC CLK_M4_EMC,

CLK_M4_EMC_DIV

3.94 7.95

SCU CLK_M4_SCU 0.1 0.21

CREG CLK_M4_CREG 0.35 0.7

Flash bank A CLK_M4_FLASHA 1.47 2.97

Flash bank B CLK_M4_FLASHB 1.4 2.84

SGPIO CLK_PERIPH_SGPIO 0.1 0.17

SPI CLK_SPI 0.07 0.11

Table 12. Peripheral power consumption

Peripheral Branch clock IDD(REG)(3V3) in mA

Branch clock

frequency = 48 MHz

Branch clock

frequency = 96 MHz

Product data sheet Rev. 1.3 — 10 January 2020 103 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

10.3 Electrical pin characteristics

Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V. Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V.

Fig 19. Standard I/O pins; typical LOW level output

current IOL versus LOW level output voltage

VOL

Fig 20. Standard I/O pins; typical HIGH level output

voltage VOH versus HIGH level output current

IOH

002aah368

016 32 48 64 80 96

2.4

2.8

3.2

3.6

IOH (mA)

VOH

(V)

-40 °C

+25 °C

+85 °C

+105 °C

002aah359

0 6 12 18 24 30 36

2.4

2.8

3.2

3.6

IOH (mA)

VOH

(V)

-40 °C

+25 °C

+85 °C

+105 °C

Product data sheet Rev. 1.3 — 10 January 2020 104 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V; normal-drive;

EHD = 0x0.

Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V;

medium-drive; EHD = 0x1.

Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V; high-drive;

EHD = 0x2.

Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V; ultra

high-drive; EHD = 0x3.

Fig 21. High-drive pins; typical LOW level output current IOL versus LOW level output voltage VOL

002aah360

0 0.1 0.2 0.3 0.4 0.5 0.6

VOL (V)

IOL

(mA)

-40 °C

+25 °C

+85 °C

+105 °C

002aah361

0 0.1 0.2 0.3 0.4 0.5 0.6

VOL (V)

IOL

(mA)

-40 °C

+25 °C

+85 °C

+105 °C

002aah362

0 0.1 0.2 0.3 0.4 0.5 0.6

VOL (V)

IOL

(mA)

-40 °C

+25 °C

+85 °C

+105 °C

002aah363

0 0.1 0.2 0.3 0.4 0.5 0.6

VOL (V)

IOL

(mA)

-40 °C

+25 °C

+85 °C

+105 °C

Product data sheet Rev. 1.3 — 10 January 2020 105 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V; normal-drive;

EHD = 0x0.

Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V;

medium-drive; EHD = 0x1.

Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V; high-drive;

EHD = 0x2.

Conditions: VDD(REG)(3V3) = VDD(IO) = 3.3 V; ultra

high-drive; EHD = 0x3.

Fig 22. High-drive pins; typical HIGH level output voltage VOH versus HGH level output current IOH

002aah364

0 4 8 12 16 20 24

2.4

2.8

3.2

3.6

IOH (mA)

VOH

(V)

-40 °C

+25 °C

+85 °C

+105 °C

002aah367

0 8 16 24 32 40 48

2.4

2.8

3.2

3.6

IOH (mA)

VOH

(V)

-40 °C

+25 °C

+85 °C

+105 °C

002aah368

016 32 48 64 80 96

2.4

2.8

3.2

3.6

IOH (mA)

VOH

(V)

-40 °C

+25 °C

+85 °C

+105 °C

002aah369

020 40 60 80 100 120

2.4

2.8

3.2

3.6

IOH (mA)

VOH

(V)

-40 °C

+25 °C

+85 °C

+105 °C

Product data sheet Rev. 1.3 — 10 January 2020 106 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

Conditions: VDD(IO) = 3.3 V. Simulated data over process and temperature.

Fig 23. Pull-up current Ipu versus input voltage VI

Conditions: VDD(IO) = 3.3 V. Simulated data over process and temperature.

Fig 24. Pull-down current Ipd versus input voltage VI

002aah422

0 1 2 3 4 5

-80

-60

-40

-20

VI (V)

Ipu

(μA)

+105 C

+105 °C

+25 C

+25 °C

-40 C

-40 °C

002aah418

0 1 2 3 4 5

120

VI (V)

Ipd

(μA)

-40 C

-40 °C

+25 C

+25 °C

+105 C

+105 °C

Product data sheet Rev. 1.3 — 10 January 2020 107 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

10.4 BOD and band gap static characteristics

[1] Interrupt and reset levels are selected by writing to the BODLV1/2 bits in the control register CREGE0, see

the LPC43xx user manual.

[1] Based on characterization, not tested in production.

Table 13. BOD static characteristics[1]

Tamb = 25 C; simulated values for nominal processing.

Symbol Parameter Conditions Min Typ Max Unit

Vth threshold voltage interrupt level 2

assertion - 2.95 - V

de-assertion - 3.03 - V

interrupt level 3

assertion - 3.05 - V

de-assertion - 3.13 - V

reset level 2

assertion - 2.1 - V

de-assertion - 2.18 - V

reset level 3

assertion - 2.2 - V

de-assertion - 2.28 - V

Table 14. Band gap characteristics

VDDA(3V3) over specified ranges; Tamb = 40 C to +105 C; unless otherwise specified

Symbol Parameter Min Typ Max Unit

Vref(bg) band gap reference voltage [1] 0.707 0.745 0.783 mV

Product data sheet Rev. 1.3 — 10 January 2020 108 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

11. Dynamic characteristics

11.1 Flash/EEPROM memory

[1] Number of erase/program cycles.

[2] Programming times are given for writing 512 bytes from RAM to the flash. Data must be written to the flash

in blocks of 512 bytes.

[1] See the LPC43xx user manual how to program the wait states for the different read (RPHASEx) and erase/program phases (PHASEx)

Table 15. Flash characteristics

Tamb = 40 C to +105 C, unless otherwise specified. VDD(REG)(3V3) = 2.4 V to 3.6 V for read

operations; VDD(REG)(3V3) = 2.7 V to 3.6 V for erase/program operations.

Symbol Parameter Conditions Min Typ Max Unit

Nendu endurance sector erase/program [1] 10 000 - - cycles

page erase/program; page

in large sector

1 000 - - cycles

page erase/program; page

in small sector

10 000 - - cycles

tret retention time powered 10 - - years

unpowered 10 - - years

ter erase time page, sector, or multiple

consecutive sectors

- 100 - ms

tprog programming

time

[2] -1-ms

Table 16. EEPROM characteristics

Tamb = 40 C to +105 C; VDD(REG)(3V3) = 2.7 V to 3.6 V.

Symbol Parameter Conditions Min Typ Max Unit

fclk clock frequency 800 1500 1600 kHz

Nendu endurance 100 000 - - cycles

tret retention time Tamb = 40 C to +85 C 20 - - years

85 C < Tamb  105 C 10 - - years

taaccess time read - 120 - ns

erase/program;

fclk = 1500 kHz

- 1.99 - ms

erase/program;

fclk = 1600 kHz

- 1.87 - ms

twait wait time read; RPHASE1 [1] 70 - - ns

read; RPHASE2 [1] 35 - - ns

write; PHASE1 [1] 20 - - ns

write; PHASE2 [1] 40 - - ns

write; PHASE3 [1] 10 - - ns

Product data sheet Rev. 1.3 — 10 January 2020 109 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

11.2 Wake-up times

[1] Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply

voltages.

[2] Tcy(clk) = 1/CCLK with CCLK = CPU clock frequency.

11.3 External clock for oscillator in slave mode

Remark: The input voltage on the XTAL1/2 pins must be  1.2 V (see Table 11). For

connecting the oscillator to the XTAL pins, also see Section 13.2 and Section 13.4.

[1] Parameters are valid over operating temperature range unless otherwise specified.

Table 17. Dynamic characteristic: Wake-up from Deep-sleep, Power-down, and Deep

power-down modes

Tamb = 40 C to +105 C

Symbol Parameter Conditions Min Typ[1] Max Unit

twake wake-up time from Sleep mode [2] 3  Tcy(clk) 5  Tcy(clk) -ns

from Deep-sleep and

Power-down mode

12 51 - s

from Deep power-down mode - 200 - μs

after reset - 200 - μs

Table 18. Dynamic characteristic: external clock

Tamb = 40 C to +105 C; VDD(IO) over specified ranges.[1]

Symbol Parameter Conditions Min Max Unit

fosc oscillator frequency 1 25 MHz

Tcy(clk) clock cycle time 40 1000 ns

tCHCX clock HIGH time Tcy(clk)  0.4 Tcy(clk)  0.6 ns

tCLCX clock LOW time Tcy(clk)  0.4 Tcy(clk)  0.6 ns

Fig 25. External clock timing (with an amplitude of at least Vi(RMS) = 200 mV)

CLCX

CHCX

cy(clk)

002aag698

Product data sheet Rev. 1.3 — 10 January 2020 110 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

11.4 Crystal oscillator

[1] Parameters are valid over operating temperature range unless otherwise specified.

[2] Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply

voltages.

[3] Indicates RMS period jitter.

[4] PLL-induced jitter is not included.

[5] Select HF = 0 in the XTAL_OSC_CTRL register.

[6] Select HF = 1 in the XTAL_OSC_CTRL register.

11.5 IRC oscillator

[1] Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply

voltages.

11.6 RTC oscillator

See Section 13.3 for connecting the RTC oscillator to an external clock source.

[1] Parameters are valid over operating temperature range unless otherwise specified.

[2] Typical ratings are not guaranteed. The values listed are at room temperature (25 C), nominal supply

voltages.

Table 19. Dynamic characteristic: oscillator

Tamb = 40 C to +105 C; VDD(IO) over specified ranges; 2.4 V  VDD(REG)(3V3)  3.6 V.[1]

Symbol Parameter Conditions Min Typ[2] Max Unit

Low-frequency mode (1-20 MHz)[5]

tjit(per) period jitter time 5 MHz crystal [3][4] - 13.2 - ps

10 MHz crystal - 6.6 - ps

15 MHz crystal - 4.8 - ps

High-frequency mode (20 - 25 MHz)[6]

tjit(per) period jitter time 20 MHz crystal [3][4] - 4.3 - ps

25 MHz crystal - 3.7 - ps

Table 20. Dynamic characteristic: IRC oscillator

2.4 V  VDD(REG)(3V3)  3.6 V

Symbol Parameter Conditions Min Typ[1] Max Unit

fosc(RC) internal RC

oscillator

frequency

-40 C  Tamb  0 C 12.0 - 3 % 12.0 12.0 + 3 % MHz

0 C  Tamb  85 C 12.0 - 1.5 % 12.0 12.0 + 1.5 % MHz

85 C  Tamb  105 C 12.0 - 3 % 12.0 12.0 + 3 % MHz

Table 21. Dynamic characteristic: RTC oscillator

Tamb = 40 C to +105 C; 2.4 V  VDD(REG)(3V3)  3.6 V or 2.4 V  VBAT  3.6 V[1]

Symbol Parameter Conditions Min Typ[1] Max Unit

fiinput frequency - - 32.768 - kHz

ICC(osc) oscillator supply

current

280 800 nA

Product data sheet Rev. 1.3 — 10 January 2020 111 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

11.7 GPCLKIN

11.8 I/O pins

For I/O pins that are configured as input only, there is no limitation on the rise and fall

times.

[1] Simulated data.

[2] Simulated using 10 cm of 50 Ω PCB trace with 5 pF receiver input. Rise and fall times measured between

80 % and 20 % of the full output signal level.

[3] The slew rate is configured in the system control block in the SFSP registers using the EHS bit. See the

LPC43xx user manual.

[4] CL = 20 pF. Rise and fall times measured between 90 % and 10 % of the full input signal level.

Table 22. Dynamic characteristic: GPCLKIN

Tamb = 25 C; 2.4 V  VDD(REG)(3V3)  3.6 V

Symbol Parameter Min Typ Max Unit

GP_CLKIN input frequency - - 25 MHz

Table 23. Dynamic characteristic: I/O pins[1]

Tamb = 40 C to +85 C; 2.7 V  VDD(IO)  3.6 V.

Symbol Parameter Conditions Min Typ Max Unit

Standard I/O pins - normal drive strength

trrise time pin configured as output; EHS = 1 [2][3] 1.0 - 2.5 ns

tffall time pin configured as output; EHS = 1 [2][3] 0.9 - 2.5 ns

trrise time pin configured as output; EHS = 0 [2][3] 1.9 - 4.3 ns

tffall time pin configured as output; EHS = 0 [2][3] 1.9 - 4.0 ns

I/O pins - high drive strength

trrise time pin configured as output; standard

drive mode (EHD = 0x0)

[2][5] 4.3 - 7.9 ns

tffall time pin configured as output; standard

drive mode (EHD = 0x0)

[2][5] 4.7 - 8.7 ns

trrise time pin configured as output; medium

drive mode (EHD = 0x1)

[2][5] 3.2 - 5.7 ns

tffall time pin configured as output; medium

drive mode (EHD = 0x1)

[2][5] 3.2 - 5.5 ns

trrise time pin configured as output; high drive

mode (EHD = 0x2)

[2][5] 2.9 - 4.9 ns

tffall time pin configured as output; high drive

mode (EHD = 0x2)

[2][5] 2.5 - 3.9 ns

trrise time pin configured as output; ultra-high

drive mode (EHD = 0x3)

[2][5] 2.8 - 4.7 ns

tffall time pin configured as output; ultra-high

drive mode (EHD = 0x3)

[2][5] 2.4 - 3.4 ns

I/O pins - high-speed

trrise time pin configured as output; EHS = 1 [2][3] 350 - 670 ps

tffall time pin configured as output; EHS = 1 [2][3] 450 - 730 ps

trrise time pin configured as output; EHS = 0 [2][3] 1.0 - 1.9 ns

tffall time pin configured as output; EHS = 0 [2][3] 1.0 - 2.0 ns

Product data sheet Rev. 1.3 — 10 January 2020 112 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

[5] The drive modes are configured in the system control block in the SFSP registers using the EHD bit. See

the LPC43xx user manual.

11.9 I2C-bus

[1] Parameters are valid over operating temperature range unless otherwise specified. See the I2C-bus specification UM10204 for details.

[2] tHD;DAT is the data hold time that is measured from the falling edge of SCL; applies to data in transmission and the acknowledge.

[3] A device must internally provide a hold time of at least 300 ns for the SDA signal (with respect to the VIH(min) of the SCL signal) to

bridge the undefined region of the falling edge of SCL.

[4] Cb = total capacitance of one bus line in pF. If mixed with Hs-mode devices, faster fall times are allowed.

[5] The maximum tf for the SDA and SCL bus lines is specified at 300 ns. The maximum fall time for the SDA output stage tf is specified at

250 ns. This allows series protection resistors to be connected in between the SDA and the SCL pins and the SDA/SCL bus lines

without exceeding the maximum specified tf.

[6] In Fast-mode Plus, fall time is specified the same for both output stage and bus timing. If series resistors are used, designers should

allow for this when considering bus timing.

[7] The maximum tHD;DAT could be 3.45 s and 0.9 s for Standard-mode and Fast-mode but must be less than the maximum of tVD;DAT or

tVD;ACK by a transition time. This maximum must only be met if the device does not stretch the LOW period (tLOW) of the SCL signal. If

the clock stretches the SCL, the data must be valid by the set-up time before it releases the clock.

[8] tSU;DAT is the data set-up time that is measured with respect to the rising edge of SCL; applies to data in transmission and the

acknowledge.

[9] A Fast-mode I2C-bus device can be used in a Standard-mode I2C-bus system but the requirement tSU;DAT = 250 ns must then be met.

This will automatically be the case if the device does not stretch the LOW period of the SCL signal. If such a device does stretch the

LOW period of the SCL signal, it must output the next data bit to the SDA line tr(max) + tSU;DAT = 1000 + 250 = 1250 ns (according to the

Standard-mode I2C-bus specification) before the SCL line is released. Also the acknowledge timing must meet this set-up time.

Table 24. Dynamic characteristic: I2C-bus pins

Tamb = 40 C to +105 C; 2.4 V  VDD(REG)(3V3)  3.6 V.[1]

Symbol Parameter Conditions Min Max Unit

fSCL SCL clock frequency Standard-mode 0 100 kHz

Fast-mode 0 400 kHz

Fast-mode Plus 0 1 MHz

tffall time [3][4][5][6] of both SDA and

SCL signals

Standard-mode

- 300 ns

Fast-mode 20 + 0.1  Cb300 ns

Fast-mode Plus - 120 ns

tLOW LOW period of the SCL clock Standard-mode 4.7 - s

Fast-mode 1.3 - s

Fast-mode Plus 0.5 - s

tHIGH HIGH period of the SCL clock Standard-mode 4.0 - s

Fast-mode 0.6 - s

Fast-mode Plus 0.26 - s

tHD;DAT data hold time [2][3][7] Standard-mode 0 - s

Fast-mode 0 - s

Fast-mode Plus 0 - s

tSU;DAT data set-up time

[8][9] Standard-mode 250 - ns

Fast-mode 100 - ns

Fast-mode Plus 50 - ns

Product data sheet Rev. 1.3 — 10 January 2020 113 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

11.10 I2S-bus interface

[1] Clock to the I2S-bus interface BASE_APB1_CLK = 150 MHz; peripheral clock to the I2S-bus interface

PCLK = BASE_APB1_CLK / 12. I2S clock cycle time Tcy(clk) = 79.2 ns, corresponds to the SCK signal in the

I2S-bus specification.

Fig 26. I2C-bus pins clock timing

002aaf425

70 %

30 %

SDA

70 %

30 %

70 %

30 %

70 %

30 %

tHD;DAT

SCL

1 / fSCL

70 %

30 % 70 %

30 %

tVD;DAT

tHIGH

tLOW

tSU;DAT

Table 25. Dynamic characteristics: I2S-bus interface pins

Tamb = 40 C to 105 C; 2.4 V  VDD(REG)(3V3)  3.6 V; 2.7 V  VDD(IO)  3.6 V; CL = 20 pF.

Conditions and data refer to I2S0 and I2S1 pins. Simulated values.

Symbol Parameter Conditions Min Typ Max Unit

common to input and output

trrise time - 4 - ns

tffall time - 4 - ns

tWH pulse width HIGH on pins I2Sx_TX_SCK

and I2Sx_RX_SCK

36 - - ns

tWL pulse width LOW on pins I2Sx_TX_SCK

and I2Sx_RX_SCK

36 - - ns

output

tv(Q) data output valid time on pin I2Sx_TX_SDA [1] - 4.4 - ns

on pin I2Sx_TX_WS - 4.3 - ns

input

tsu(D) data input set-up time on pin I2Sx_RX_SDA [1] -0-ns

on pin I2Sx_RX_WS 0.20 ns

th(D) data input hold time on pin I2Sx_RX_SDA [1] - 3.7 - ns

on pin I2Sx_RX_WS - 3.9 - ns

Product data sheet Rev. 1.3 — 10 January 2020 114 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

11.11 USART interface

Fig 27. I2S-bus timing (transmit)

Fig 28. I2S-bus timing (receive)

002aag497

I2Sx_TX_SCK

I2Sx_TX_SDA

I2Sx_TX_WS

Tcy(clk) tftr

tWH tWL

tv(Q)

002aag498

Tcy(clk) tftr

tWH

tsu(D) th(D)

tsu(D) tsu(D)

tWL

I2Sx_RX_SCK

I2Sx_RX_SDA

I2Sx_RX_WS

Table 26. USART dynamic characteristics

Tamb = 40 C to 105 C; 2.4 V  VDD(REG)(3V3)  3.6 V; 2.7 V  VDD(IO)  3.6 V; CL = 20 pF. EHS = 1

for all pins. Simulated values.

Symbol Parameter Min Max Unit

USART master (in synchronous mode)

tsu(D) data input set-up time 26.6 - ns

th(D) data input hold time 0 - ns

tv(Q) data output valid time 0 10.4 ns

USART slave (in synchronous mode)

tsu(D) data input set-up time 2.4 - ns

th(D) data input hold time 0 - ns

tv(Q) data output valid time 4.3 24.3 ns

Product data sheet Rev. 1.3 — 10 January 2020 115 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

Fig 29. USART timing

SCLK (FES = 1)

TXD

RXD

Tcy(clk)

tv(Q) tv(Q)

th(D)

tsu(D)

START BIT0

SCLK (FES = 0)

START BIT0 BIT1

BIT1

aaa-016717

Product data sheet Rev. 1.3 — 10 January 2020 116 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

11.12 SSP interface

Table 27. Dynamic characteristics: SSP pins in SPI mode

Tamb = 40 C to +105 C; 2.4 V  VDD(REG)(3V3)  3.6 V; 2.7 V  VDD(IO)  3.6 V; CL = 20 pF; sampled at 10 % and 90 % of

the signal level; EHS = 1 for all pins. Simulated values.

Symbol Parameter Conditions Min Typ Max Unit

SSP master

Tcy(clk) clock cycle time full-duplex mode [1] 1/(25.5  106)- - s

when only transmitting 1/(51  106)- - s

tDS data set-up time in SPI mode 12.2 - - ns

tDH data hold time in SPI mode 3.6 - - ns

tv(Q) data output valid

time

in SPI mode - - 6.7 ns

th(Q) data output hold

time

in SPI mode 1.7 - - ns

tlead lead time continuous transfer mode

SPI mode; CPOL = 0;

CPHA = 0

Tcy(clk) + 3.3 - Tcy(clk) + 8.2 ns

SPI mode; CPOL = 0;

CPHA = 1

0.5  Tcy(clk) + 3.3 - 0.5  Tcy(clk) + 8.2 ns

SPI mode; CPOL = 1;

CPHA = 0

Tcy(clk) + 3.3 - Tcy(clk) + 8.2 ns

SPI mode; CPOL = 1;

CPHA = 1

0.5  Tcy(clk) + 3.3 - 0.5  Tcy(clk) + 8.2 ns

synchronous serial

frame mode

0.5  Tcy(clk) + 3.3 - 0.5  Tcy(clk) + 8.2 ns

microwire frame format Tcy(clk) + 3.3 - Tcy(clk) + 8.2 ns

tlag lag time continuous transfer mode

SPI mode; CPOL = 0;

CPHA = 0

0.5  Tcy(clk) -- ns

SPI mode; CPOL = 0;

CPHA = 1

Tcy(clk) -- ns

SPI mode; CPOL = 1;

CPHA = 0

0.5  Tcy(clk) -- ns

SPI mode; CPOL = 1;

CPHA = 1

Tcy(clk) -- ns

synchronous serial

frame mode

Tcy(clk) -- ns

microwire frame format 0.5  Tcy(clk) -- ns

Product data sheet Rev. 1.3 — 10 January 2020 117 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

tddelay time continuous transfer mode

SPI mode; CPOL = 0;

CPHA = 0

- 0.5  Tcy(clk) -ns

SPI mode; CPOL = 0;

CPHA = 1

- n/a - ns

SPI mode; CPOL = 1;

CPHA = 0

- 0.5  Tcy(clk) -ns

SPI mode; CPOL = 1;

CPHA = 1

- n/a - ns

synchronous serial

frame mode

-T

cy(clk) -ns

microwire frame format - n/a - ns

SSP slave

PCLK Peripheral clock

frequency

- - 204 MHz

Tcy(clk) clock cycle time [2] 1/(11 106)- - s

tDS data set-up time in SPI mode 1.5 - - ns

tDH data hold time in SPI mode 2 - - ns

tv(Q) data output valid

time

in SPI mode - - [4  (1/PCLK)] + 1 ns

th(Q) data output hold

time

in SPI mode 4.5 - - ns

tlead lead time continuous transfer mode

SPI mode; CPOL = 0;

CPHA = 0

Tcy(clk) -- ns

SPI mode; CPOL = 0;

CPHA = 1

0.5  Tcy(clk) -- ns

SPI mode; CPOL = 1;

CPHA = 0

Tcy(clk) -- ns

SPI mode; CPOL = 1;

CPHA = 1

0.5  Tcy(clk) -- ns

synchronous serial

frame mode

0.5  Tcy(clk) -- ns

microwire frame format Tcy(clk) -- ns

Table 27. Dynamic characteristics: SSP pins in SPI mode

Tamb = 40 C to +105 C; 2.4 V  VDD(REG)(3V3)  3.6 V; 2.7 V  VDD(IO)  3.6 V; CL = 20 pF; sampled at 10 % and 90 % of

the signal level; EHS = 1 for all pins. Simulated values.

Symbol Parameter Conditions Min Typ Max Unit

Product data sheet Rev. 1.3 — 10 January 2020 118 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

[1] Tcy(clk) = (SSPCLKDIV  (1 + SCR)  CPSDVSR) / fmain. The clock cycle time derived from the SPI bit rate Tcy(clk) is a function of the

main clock frequency fmain, the SSP peripheral clock divider (SSPCLKDIV), the SSP SCR parameter (specified in the SSP0CR0

[2] Tcy(clk) 12  Tcy(PCLK).

tlag lag time continuous transfer mode

SPI mode; CPOL = 0;

CPHA = 0

0.5 x Tcy(clk) + 1.5 - - ns

SPI mode; CPOL = 0;

CPHA = 1

Tcy(clk) + 1.5 - - ns

SPI mode; CPOL = 1;

CPHA = 0

0.5  Tcy(clk) + 1.5 - - ns

SPI mode; CPOL = 1;

CPHA = 1

Tcy(clk) + 1.5 - - ns

synchronous serial

frame mode

Tcy(clk) + 1.5 - - ns

microwire frame format 0.5  Tcy(clk) -- ns

tddelay time continuous transfer mode

SPI mode; CPOL = 0;

CPHA = 0

- 0.5  Tcy(clk) -ns

SPI mode; CPOL = 0;

CPHA = 1

- n/a - ns

SPI mode; CPOL = 1;

CPHA = 0

- 0.5  Tcy(clk) -ns

SPI mode; CPOL = 1;

CPHA = 1

- n/a - ns

synchronous serial

frame mode

-T

cy(clk) -ns

microwire frame format - n/a - ns

Table 27. Dynamic characteristics: SSP pins in SPI mode

Tamb = 40 C to +105 C; 2.4 V  VDD(REG)(3V3)  3.6 V; 2.7 V  VDD(IO)  3.6 V; CL = 20 pF; sampled at 10 % and 90 % of

the signal level; EHS = 1 for all pins. Simulated values.

Symbol Parameter Conditions Min Typ Max Unit

Product data sheet Rev. 1.3 — 10 January 2020 119 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

11.13 SPI interface

[1] Tcy(clk) = 8/BASE_SPI_CLK. Tcy(PCLK) = 1/BASE_SPI_CLK.

Table 28. Dynamic characteristics: SPI

Tamb = 40 C to +105 C; 2.4 V  VDD(REG)(3V3)  3.6 V; 2.7 V  VDD(IO)  3.6 V. Simulated values.

Symbol Parameter Conditions Min Typ Max Unit

Tcy(PCLK) PCLK cycle time 5 ns

Tcy(clk) clock cycle time [1] 40 - - ns

Master

tDS data set-up time 7.2 - - ns

tDH data hold time 0 - - ns

tv(Q) data output valid time - - 3.7 ns

th(Q) data output hold time - - 1.2 ns

Slave

tDS data set-up time 1.2 - - ns

tDH data hold time 3 x Tcy(PCLK) + 0.54 - - ns

tv(Q) data output valid time - - 3 x Tcy(PCLK) + 9.7 ns

th(Q) data output hold time - - 2 x Tcy(PCLK) + 7.1 ns

Product data sheet Rev. 1.3 — 10 January 2020 120 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

11.14 SSP/SPI timing diagrams

Fig 30. SSP in SPI mode and SPI master timing

SCK (CPOL = 0)

MOSI (CPHA = 1)

SSEL

MISO (CPHA = 1)

Tcy(clk)

tDS tDH

tv(Q)

DATA VALID (LSB) DATA VALID

th(Q)

SCK (CPOL = 1)

DATA VALID (LSB) DATA VALID

MOSI (CPHA = 0)

MISO (CPHA = 0) tDS

tlead tlag

tDH

DATA VALID (MSB) DATA VALID (MSB)DATA VALID

DATA VALID (LSB)

th(Q)

DATA VALID DATA VALID

tv(Q)

aaa-013462

DATA VALID (MSB)

DATA VALID (MSB) IDLE

IDLE

DATA VALID (MSB)

Product data sheet Rev. 1.3 — 10 January 2020 121 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

Fig 31. SSP in SPI mode and SPI slave timing

SCK (CPOL = 0)

MISO (CPHA = 1)

SSEL

MOSI (CPHA = 1)

Tcy(clk)

tDS tDH

tv(Q)

DATA VALID (LSB) DATA VALID

th(Q)

SCK (CPOL = 1)

DATA VALID (LSB) DATA VALID

MISO (CPHA = 0)

MOSI (CPHA = 0) tDS

tlead tlag

tDH

DATA VALID (MSB) DATA VALID (MSB)DATA VALID

DATA VALID (LSB)

th(Q)

DATA VALID (MSB) DATA VALID

tv(Q)

aaa-014942

DATA VALID (MSB)

IDLE

DATA VALID (MSB)

Product data sheet Rev. 1.3 — 10 January 2020 122 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

11.15 SPIFI

11.16 SGPIO timing

The following considerations apply to SGPIO timing:

•SGPIO input signals are synchronized by the internal clock SGPIO_CLOCK. To

guarantee that no samples are missed, all input signals should have a duration of at

least one SGPIO_CLOCK cycle plus the set-up and hold times.

•When an external clock input is used to generate output data, synchronization causes

a latency of at least one SGPIO_CLOCK cycle. The maximum output data rate is one

output every two SGPIO_CLOCK cycles.

•Synchronization also causes a latency of one SGPIO_CLOCK cycle when sampling

several inputs. This may cause inputs with very similar timings to be sampled with a

difference of one SGPIO_CLOCK cycle.

Table 29. Dynamic characteristics: SPIFI

Tamb = 40 C to 105 C; 2.4 V  VDD(REG)(3V3)  3.6 V; 2.7 V  VDD(IO)  3.6 V. CL = 20 pF. Sampled

at 90 % and 10 % of the signal level. EHS = 1 for all pins. Simulated values.

Symbol Parameter Min Max Unit

Tcy(clk) clock cycle time 9.6 - ns

tDS data set-up time 3.2 - ns

tDH data hold time 0 - ns

tv(Q) data output valid time - 3.2 ns

th(Q) data output hold time 0.6 - ns

Fig 32. SPIFI timing (Mode 0)

SPIFI_SCK

SPIFI data out

SPIFI data in

Tcy(clk)

tDS tDH

tv(Q)

DATA VALID DATA VALID

th(Q)

DATA VALID DATA VALID

002aah409

Product data sheet Rev. 1.3 — 10 January 2020 123 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

[1] SGPIO_CLOCK is the internally generated SGPIO clock. TSGPIO = 1/fSGPIO_CLOCK.

Table 30. Dynamic characteristics: SGPIO

Tamb = 40 C to +85 C; 2.4 V  VDD(REG)(3V3)  3.6 V; 2.7 V  VDD(IO)  3.6 V. Simulated values.

Symbol Parameter Conditions Min Typ Max Unit

tsu(D) data input set-up time 2 - - ns

th(D) data input hold time [1] TSGPIO + 2 - - ns

tsu(D) data input set-up time sampled by

SGPIO_CLOCK

[1] TSGPIO + 2 - - ns

th(D) data input hold time sampled by

SGPIO_CLOCK

[1] TSGPIO + 2 - - ns

tv(Q) data output valid time [1] - - 2 x TSGPIO ns

th(Q) data output hold time [1] TSGPIO -ns

tv(Q) data output valid time sampled by

SGPIO_CLOCK

[1] -3 - 3 ns

th(Q) data output hold time sampled by

SGPIO_CLOCK

[1] -3 - 3 ns

Fig 33. SGPIO timing

SGPIO_CLOCK

DIN

CLKINext

sync(CLKINext) = CLKINi

sync(DIN)

Dout

CLKout

DINi

DQi

th(D)

tsu(D)

th(Q)

tv(Q)

002aah668

Product data sheet Rev. 1.3 — 10 January 2020 124 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

11.17 External memory interface

Table 31. Dynamic characteristics: Static asynchronous external memory interface

CL = 22 pF for EMC_Dn CL = 20 pF for all others; Tamb = 40 C to 105 C; 2.4 V  VDD(REG)(3V3)  3.6 V;

2.7 V  VDD(IO)  3.6 V; values guaranteed by design; the values in the table have been calculated with WAITTURN = 0x0 in

STATICWAITTURN register. Timing parameters are given for single memory access cycles. In a normal read operation, the

EMC changes the address while CS is asserted which results in multiple memory accesses.

Symbol Parameter[1] Conditions Min Typ Max Unit

Read cycle parameters

tCSLAV CS LOW to address valid

time

3.1 - 1.6 ns

tCSLOEL CS LOW to OE LOW time [2][2] 0.6 + Tcy(clk) 

WAITOEN

- 1.3 + Tcy(clk) 

WAITOEN

tCSLBLSL CS LOW to BLS LOW time PB = 1 0.7 - 1.8 ns

tOELOEH OE LOW to OE HIGH time [2] 0.6 +

(WAITRD 

WAITOEN + 1) 

Tcy(clk)

-0.4 +

(WAITRD 

WAITOEN + 1) 

Tcy(clk)

tam memory access time - - 16 +

(WAITRD 

WAITOEN +1) 

Tcy(clk)

th(D) data input hold time 16 - - ns

tCSHBLSH CS HIGH to BLS HIGH

time

PB = 1 0.4 - 1.9 ns

tCSHOEH CS HIGH to OE HIGH time 0.4 - 1.4 ns

tOEHANV OE HIGH to address invalid PB = 1 2.0 - 2.6 ns

tCSHEOR CS HIGH to end of read

time

[3] 2.0 - 0 ns

tCSLSOR CS LOW to start of read

time

[4] 0 - 1.8 ns

Write cycle parameters

tCSLAV CS LOW to address valid

time

3.1 - 1.6 ns

tCSLDV CS LOW to data valid time 3.1 - 1.5 ns

tCSLWEL CS LOW to WE LOW time PB = 1 1.5 +

(WAITWEN + 1)

 Tcy(clk)

- 0.2 +

(WAITWEN + 1)

 Tcy(clk)

tCSLBLSL CS LOW to BLS LOW time PB = 1 0.7 - 1.8 ns

tWELWEH WE LOW to WE HIGH time PB = 1 [2] 0.6 +

(WAITWR 

WAITWEN + 1)

 Tcy(clk)

-0.4 +

(WAITWR 

WAITWEN + 1)

 Tcy(clk)

tWEHDNV WE HIGH to data invalid

time

PB = 1 [2] 0.9 + Tcy(clk) - 2.3 + Tcy(clk) ns

tWEHEOW WE HIGH to end of write

time

PB = 1 [2][5] 0.4 + Tcy(clk) -0.3 + Tcy(clk) ns

tCSLBLSL CS LOW to BLS LOW PB = 0 0.7 +

(WAITWEN + 1)

 Tcy(clk)

- 1.8 +

(WAITWEN + 1)

 Tcy(clk)

Product data sheet Rev. 1.3 — 10 January 2020 125 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

[1] Parameters specified for 40 % of VDD(IO) for rising edges and 60 % of VDD(IO) for falling edges.

[2] Tcy(clk) = 1/CCLK (see LPC43xx/LPC43Sxx User manual).

[3] End Of Read (EOR): longest of tCSHOEH, tOEHANV, tCSHBLSH.

[4] Start Of Read (SOR): longest of tCSLAV, tCSLOEL, tCSLBLSL.

[5] End Of Write (EOW): earliest of address not valid or EMC_BLSn HIGH.

tBLSLBLSH BLS LOW to BLS HIGH

time

PB = 0 [2] 0.9 +

(WAITWR 

WAITWEN + 1)

 Tcy(clk)

-0.1 +

(WAITWR 

WAITWEN + 1)

 Tcy(clk)

tBLSHEOW BLS HIGH to end of write

time

PB = 0 [2][5] 1.9 + Tcy(clk) -0.5 + Tcy(clk) ns

tBLSHDNV BLS HIGH to data invalid

time

PB = 0 [2] 2.5 + Tcy(clk) - 1.4 + Tcy(clk) ns

tCSHEOW CS HIGH to end of write

time

[5] 2.0 - 0 ns

tBLSHDNV BLS HIGH to data invalid

time

PB = 1 2.5 - 1.4 ns

tWEHANV WE HIGH to address

invalid time

PB = 1 0.9 + Tcy(clk) - 2.4 + Tcy(clk) ns

Table 31. Dynamic characteristics: Static asynchronous external memory interface …continued

CL = 22 pF for EMC_Dn CL = 20 pF for all others; Tamb = 40 C to 105 C; 2.4 V  VDD(REG)(3V3)  3.6 V;

2.7 V  VDD(IO)  3.6 V; values guaranteed by design; the values in the table have been calculated with WAITTURN = 0x0 in

STATICWAITTURN register. Timing parameters are given for single memory access cycles. In a normal read operation, the

EMC changes the address while CS is asserted which results in multiple memory accesses.

Symbol Parameter[1] Conditions Min Typ Max Unit

Fig 34. External static memory read/write access (PB = 0)

tCSLDV

tCSLBLSL

tCSHEOW

tBLSHEOW

tCSLAV

EOR

SOR EOW

EMC_An

EMC_CSn

EMC_OE

EMC_BLSn

EMC_WE

EMC_Dn

002aag699

tCSHOEH

tOEHANV

tCSHEOR

tam

tCSLSOR

tOELOEH

tCSLOEL

tCSLAV

th(D)

tBLSLBLSH

tBLSHDNV

Product data sheet Rev. 1.3 — 10 January 2020 126 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

Fig 35. External static memory read/write access (PB = 1)

EMC_An

tCSLAV

tCSLBLSL

EMC_CSn

EMC_OE

EMC_BLSn

EMC_WE

tCSLSOR

tCSLDV

tam

th(D)

EOR

SOR EOW

EMC_Dn

tCSLWEL tWELWEH tWEHEOW

002aag700

tCSLBLSL

tCSLAV

tCSLOEL

tOELOEH

tCSHOEH

tOEHANV

tCSHBLSH

tCSHEOR

tCSHEOW

tWEHDNV

tBLSHDNV

Product data sheet Rev. 1.3 — 10 January 2020 127 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

[1] Program the EMC_CLKn delay values in the EMCDELAYCLK register (see the LPC43xx User manual).

The delay values must be the same for all SDRAM clocks EMC_CLKn: CLK0_DELAY = CLK1_DELAY =

CLK2_DELAY = CLK3_DELAY.

Table 32. Dynamic characteristics: Dynamic external memory interface

Simulated data over temperature and process range; CL = 10 pF for EMC_DYCSn, EMC_RAS, EMC_CAS, EMC_WE,

EMC_An; CL = 9 pF for EMC_Dn; CL = 5 pF for EMC_DQMOUTn, EMC_CLKn, EMC_CKEOUTn; Tamb = 40 C to 105 C;

2.4 V  VDD(REG)(3V3)  3.6 V; VDD(IO) =3.3 V  10 %; RD = 1 (see LPC43xx/LPC43Sxx User manual); EMC_CLKn delays

CLK0_DELAY = CLK1_DELAY = CLK2_DELAY = CLK3_DELAY = 0.

Symbol Parameter Min Typ Max Unit

Tcy(clk) clock cycle time 8.4 - - ns

Common to read and write cycles

td(DYCSV) dynamic chip select valid delay time - 3.1 + 0.5  Tcy(clk) 5.1 + 0.5  Tcy(clk) ns

th(DYCS) dynamic chip select hold time 0.3 + 0.5  Tcy(clk) 0.9 + 0.5  Tcy(clk) -ns

td(RASV) row address strobe valid delay time - 3.1 + 0.5  Tcy(clk) 4.9 + 0.5  Tcy(clk) ns

th(RAS) row address strobe hold time 0.5 + 0.5  Tcy(clk) 1.1 + 0.5  Tcy(clk) -ns

td(CASV) column address strobe valid delay time - 2.9 + 0.5  Tcy(clk) 4.6 + 0.5  Tcy(clk) ns

th(CAS) column address strobe hold time 0.3 + 0.5  Tcy(clk) 0.9 + 0.5  Tcy(clk) -ns

td(WEV) write enable valid delay time - 3.2 + 0.5  Tcy(clk) 5.9 + 0.5  Tcy(clk) ns

th(WE) write enable hold time 1.3 + 0.5  Tcy(clk) 1.4 + 0.5  Tcy(clk) -ns

td(DQMOUTV) DQMOUT valid delay time - 3.1 + 0.5  Tcy(clk) 5.0 + 0.5  Tcy(clk) ns

th(DQMOUT) DQMOUT hold time 0.2 + 0.5  Tcy(clk) 0.8 + 0.5  Tcy(clk) -ns

td(AV) address valid delay time - 3.8 + 0.5  Tcy(clk) 6.3 + 0.5  Tcy(clk) ns

th(A) address hold time 0.3 + 0.5  Tcy(clk) 0.9 + 0.5  Tcy(clk) -ns

td(CKEOUTV) CKEOUT valid delay time - 3.1 + 0.5  Tcy(clk) 5.1 + 0.5  Tcy(clk) ns

th(CKEOUT) CKEOUT hold time 0.5  Tcy(clk) 0.7 + 0.5  Tcy(clk) -ns

Read cycle parameters

tsu(D) data input set-up time 1.5 0.5 - ns

th(D) data input hold time 2.2 0.8 - ns

Write cycle parameters

td(QV) data output valid delay time - 3.8 + 0.5  Tcy(clk) 6.2 + 0.5  Tcy(clk) ns

th(Q) data output hold time 0.5  Tcy(clk) 0.7 + 0.5  Tcy(clk) -ns

Table 33. Dynamic characteristics: Dynamic external memory interface; EMC_CLK[3:0]

delay values

Tamb = 40 C to 105 C; VDD(IO) =3.3 V  10 %; 2.4 V  VDD(REG)(3V3)  3.6 V.

Symbol Parameter Conditions Min Typ Max Unit

tddelay time delay value

CLKn_DELAY = 0

[1]

0.0 0.0 0.0 ns

CLKn_DELAY = 1 [1] 0.4 0.5 0.8 ns

CLKn_DELAY = 2 [1] 0.7 1.0 1.7 ns

CLKn_DELAY = 3 [1] 1.1 1.6 2.5 ns

CLKn_DELAY = 4 [1] 1.4 2.0 3.3 ns

CLKn_DELAY = 5 [1] 1.7 2.6 4.1 ns

CLKn_DELAY = 6 [1] 2.1 3.1 4.9 ns

CLKn_DELAY = 7 [1] 2.5 3.6 5.8 ns

Product data sheet Rev. 1.3 — 10 January 2020 128 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

For the programmable EMC_CLK[3:0] clock delays CLKn_DELAY, see Figure 32.

Remark: For SDRAM operation, set CLK0_DELAY = CLK1_DELAY = CLK2_DELAY = CLK3_DELAY in the EMCDELAYCLK

Fig 36. SDRAM timing

002aag703

Tcy(clk)

EMC_CLKn

delay = 0

EMC_CLKn

delay > 0

EMC_DYCSn,

EMC_RAS,

EMC_CAS,

EMC_WE,

EMC_CKEOUTn,

EMC_A[22:0],

EMC_DQMOUTn

th(Q)

th(Q) - td

th(D)

tsu(D)

th(D)

tsu(D)

EMC_D[31:0]

write

EMC_D[31:0]

read; delay = 0

EMC_D[31:0]

read; delay > 0

th(x) - td

td(xV) - td

td(QV) - td

td(QV)

th(x)

td(xV)

EMC_CLKn delay td; programmable CLKn_DELAY

Product data sheet Rev. 1.3 — 10 January 2020 129 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

11.18 USB interface

[1] Characterized but not implemented as production test. Guaranteed by design.

Remark: If only USB0 (HS USB) is used, the pins VDDREG and VDDIO can be at

different voltages within the operating range but should have the same ramp up time. If

USB1(FS USB) is used, the pins VDDREG and VDDIO should be a minimum of 3.0 V and

be tied together.

Table 34. Dynamic characteristics: USB0 and USB1 pins (full-speed)

CL = 50 pF; Rpu = 1.5 k on D+ to VDD(IO), unless otherwise specified; 3.0 V  VDD(IO)  3.6 V.

Symbol Parameter Conditions Min Typ Max Unit

trrise time 10 % to 90 % 4.0 - 20.0 ns

tffall time 10 % to 90 % 4.0 - 20.0 ns

tFRFM differential rise and fall time match-

ing

tr / tf90 - 111.11 %

VCRS output signal crossover voltage 1.3 - 2.0 V

tFEOPT source SE0 interval of EOP see Figure 37 160 - 175 ns

tFDEOP source jitter for differential transition

to SE0 transition

see Figure 37 2 - +5 ns

tJR1 receiver jitter to next transition 18.5 - +18.5 ns

tJR2 receiver jitter for paired transitions 10 % to 90 % 9 - +9 ns

tEOPR1 EOP width at receiver must reject as

EOP; see

Figure 37

[1] 40 - - ns

tEOPR2 EOP width at receiver must accept as

EOP; see

Figure 37

[1] 82 - - ns

Fig 37. Differential data-to-EOP transition skew and EOP width

002aab561

TPERIOD

differential

data lines

crossover point

source EOP width: tFEOPT

receiver EOP width: tEOPR1, tEOPR2

crossover point

extended

differential data to

SE0/EOP skew

n × TPERIOD + tFDEOP

Product data sheet Rev. 1.3 — 10 January 2020 130 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

[1] Characterized but not implemented as production test.

[2] Total average power consumption.

[3] The driver is active only 20 % of the time.

11.19 Ethernet

Remark: The timing characteristics of the ENET_MDC and ENET_MDIO signals comply

with the IEEE standard 802.3.

Table 35. Static characteristics: USB0 PHY pins[1]

Symbol Parameter Conditions Min Typ Max Unit

High-speed mode

Pcons power consumption [2] -68- mW

IDDA(3V3) analog supply current (3.3 V) on pin USB0_VDDA3V3_DRIVER;

total supply current

[3]

-18- mA

during transmit - 31 - mA

during receive - 14 - mA

with driver tri-stated - 14 - mA

IDDD digital supply current - 7 - mA

Full-speed/low-speed mode

Pcons power consumption [2] -15- mW

IDDA(3V3) analog supply current (3.3 V) on pin USB0_VDDA3V3_DRIVER;

total supply current - 3.5 - mA

during transmit - 5 - mA

during receive - 3 - mA

with driver tri-stated - 3 - mA

IDDD digital supply current - 3 - mA

Suspend mode

IDDA(3V3) analog supply current (3.3 V) - 24 - A

with driver tri-stated - 24 - A

with OTG functionality enabled - 3 - mA

IDDD digital supply current - 30 - A

VBUS detector outputs

Vth threshold voltage for VBUS valid 4.4 - - V

for session end 0.2 - 0.8 V

for A valid 0.8 - 2 V

for B valid 2 - 4 V

Vhys hysteresis voltage for session end - 150 10 mV

A valid - 200 10 mV

B valid - 200 10 mV

Product data sheet Rev. 1.3 — 10 January 2020 131 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

[1] Output drivers can drive a load  25 pF accommodating over 12 inch of PCB trace and the input

capacitance of the receiving device.

[2] Timing values are given from the point at which the clock signal waveform crosses 1.4 V to the valid input or

output level.

Table 36. Dynamic characteristics: Ethernet

Tamb = 40 C to 105 C, 2.4 V  VDD(REG)(3V3)  3.6 V; 2.7 V  VDD(IO)  3.6 V. Values guaranteed

by design.

Symbol Parameter Conditions Min Max Unit

RMII mode

fclk clock frequency for ENET_RX_CLK [1] - 50 MHz

clk clock duty cycle [1] 50 50 %

tsu set-up time for ENET_TXDn, ENET_TX_EN,

ENET_RXDn, ENET_RX_ER,

ENET_RX_DV

[1][2] 4- ns

thhold time for ENET_TXDn, ENET_TX_EN,

ENET_RXDn, ENET_RX_ER,

ENET_RX_DV

[1][2] 2- ns

MII mode

fclk clock frequency for ENET_TX_CLK [1] - 25 MHz

clk clock duty cycle [1] 50 50 %

tsu set-up time for ENET_TXDn, ENET_TX_EN,

ENET_TX_ER

[1][2] 4- ns

thhold time for ENET_TXDn, ENET_TX_EN,

ENET_TX_ER

[1][2] 2- ns

fclk clock frequency for ENET_RX_CLK [1] - 25 MHz

clk clock duty cycle [1] 50 50 %

tsu set-up time for ENET_RXDn, ENET_RX_ER,

ENET_RX_DV

[1][2] 4- ns

thhold time for ENET_RXDn, ENET_RX_ER,

ENET_RX_DV

[1][2] 2- ns

Fig 38. Ethernet timing

002aag210

tsu

ENET_RX_CLK

ENET_TX_CLK

ENET_RXD[n]

ENET_RX_DV

ENET_RX_ER

ENET_TXD[n]

ENET_TX_EN

ENET_TX_ER

Product data sheet Rev. 1.3 — 10 January 2020 132 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

11.20 SD/MMC

11.21 LCD

Table 37. Dynamic characteristics: SD/MMC

Tamb = 40 C to +105 C, 2.4 V  VDD(REG)(3V3)  3.6 V; 2.7 V  VDD(IO)  3.6 V, CL = 20 pF.

SAMPLE_DELAY = 0x9, DRV_DELAY = 0x6 in the SDDELAY register, sampled at 90 % and 10 %

of the signal level, EHS = 1 for SD_CLK pin, EHS = 0 for SD_DATn and SD_CMD pins. Simulated

values.

Symbol Parameter Conditions Min Max Unit

fclk clock frequency on pin SD_CLK; data transfer mode - 52 MHz

tsu(D) data input set-up time on pins SD_DATn as inputs 5.2 - ns

on pins SD_CMD as inputs 7 - ns

th(D) data input hold time on pins SD_DATn as inputs 0.2 - ns

on pins SD_CMD as inputs 1ns

td(QV) data output valid delay

time

on pins SD_DATn as outputs - 15.7 ns

on pins SD_CMD as outputs - 15.9 ns

th(Q) data output hold time on pins SD_DATn as outputs 3.5 - ns

on pins SD_CMD as outputs 3.5 - ns

Fig 39. SD/MMC timing

002aag204

SD_CLK

SD_DATn (O)

SD_DATn (I)

td(QV)

th(D)

tsu(D)

Tcy(clk)

th(Q)

SD_CMD (O)

SD_CMD (I)

Table 38. Dynamic characteristics: LCD

Tamb = 40 C to 105 C; 2.4 V  VDD(REG)(3V3)  3.6 V; 2.7 V  VDD(IO)  3.6 V; CL = 20 pF.

Simulated values.

Symbol Parameter Conditions Min Typ Max Unit

fclk clock frequency on pin LCD_DCLK - 50 - MHz

td(QV) data output valid

delay time

- - 17 ns

th(Q) data output hold time 8.5 - - ns

Product data sheet Rev. 1.3 — 10 January 2020 133 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

12. ADC/DAC electrical characteristics

[1] The ADC is monotonic, there are no missing codes.

[2] The differential linearity error (ED) is the difference between the actual step width and the ideal step width. See Figure 40.

[3] The integral non-linearity (EL(adj)) is the peak difference between the center of the steps of the actual and the ideal transfer curve after

appropriate adjustment of gain and offset errors. See Figure 40.

[4] The offset error (EO) is the absolute difference between the straight line which fits the actual curve and the straight line which fits the

ideal curve. See Figure 40.

[5] The gain error (EG) is the relative difference in percent between the straight line fitting the actual transfer curve after removing offset

error, and the straight line which fits the ideal transfer curve. See Figure 40.

[6] The absolute error (ET) is the maximum difference between the center of the steps of the actual transfer curve of the non-calibrated

ADC and the ideal transfer curve. See Figure 40.

[7] Tamb = 25 C.

[8] Input resistance Ri depends on the sampling frequency fs: Ri = 2 k + 1 / (fs  Cia).

Table 39. ADC characteristics

VDDA(3V3) over specified ranges; Tamb = 40 C to +105 C; unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Unit

VIA analog input voltage 0 - VDDA(3V3) V

Cia analog input capacitance - - 2 pF

EDdifferential linearity error 2.7 V  VDDA(3V3)  3.6 V [1][2] -0.8 - LSB

2.4 V  VDDA(3V3) < 2.7 V - 1.0 - LSB

EL(adj) integral non-linearity 2.7 V  VDDA(3V3)  3.6 V [3] -0.8 - LSB

2.4 V  VDDA(3V3) < 2.7 V - 1.5 - LSB

EOoffset error 2.7 V  VDDA(3V3)  3.6 V [4] -0.15 - LSB

2.4 V  VDDA(3V3) < 2.7 V - 0.15 - LSB

EGgain error 2.7 V  VDDA(3V3)  3.6 V [5] -0.3 - %

2.4 V  VDDA(3V3) < 2.7 V - 0.35 - %

ETabsolute error 2.7 V  VDDA(3V3)  3.6 V [6] -3 - LSB

2.4 V  VDDA(3V3) < 2.7 V - 4 - LSB

Rvsi voltage source interface

resistance

see Figure 41 - - 1/(7  fclk(ADC) 

Cia)

k

Riinput resistance [7][8] - - 1.2 M

fclk(ADC) ADC clock frequency - - 4.5 MHz

fssampling frequency 10-bit resolution; 11 clock

cycles

- - 400 kSamples/s

2-bit resolution; 3 clock

cycles

1.5 MSamples/s

Product data sheet Rev. 1.3 — 10 January 2020 134 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

(1) Example of an actual transfer curve.

(2) The ideal transfer curve.

(3) Differential linearity error (ED).

(4) Integral non-linearity (EL(adj)).

(5) Center of a step of the actual transfer curve.

Fig 40. 10-bit ADC characteristics

002aaf959

1023

1022

1021

1020

1019

(2)

(1)

10241018 1019 1020 1021 1022 1023

7123456

1018

(5)

(4)

(3)

1 LSB

(ideal)

code

out

VDDA(3V3) − VSSA

1024

offset

error

gain

error

offset error

VIA (LSBideal)

1 LSB =

Product data sheet Rev. 1.3 — 10 January 2020 135 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

[1] In the DAC CR register, bit BIAS = 0 (see the LPC43xx/LPC43Sxx user manual).

[2] Settling time is calculated within 1/2 LSB of the final value.

Rs < 1/((7  fclk(ADC)  Cia)  2 k

Fig 41. ADC interface to pins

LPC43xx

ADC0_n/ADC1_n

Cia = 2 pF

Rvsi

VSS

VEXT

002aah084

ADC

COMPARATOR

2 kΩ (analog pin)

2.2 kΩ (multiplexed pin)

Table 40. DAC characteristics

VDDA(3V3) over specified ranges; Tamb = 40 C to +105 C; unless otherwise specified

Symbol Parameter Conditions Min Typ Max Unit

EDdifferential linearity error 2.7 V  VDDA(3V3)  3.6 V [1] -0.8 - LSB

2.4 V  VDDA(3V3) < 2.7 V - 1.0 - LSB

EL(adj) integral non-linearity code = 0 to 975

2.7 V  VDDA(3V3)  3.6 V

[1] -1.0 - LSB

2.4 V  VDDA(3V3) < 2.7 V - 1.5 - LSB

EOoffset error 2.7 V  VDDA(3V3)  3.6 V [1] -0.8 - LSB

2.4 V  VDDA(3V3) < 2.7 V - 1.0 - LSB

EGgain error 2.7 V  VDDA(3V3)  3.6 V [1] -0.3 - %

2.4 V  VDDA(3V3) < 2.7 V - 1.0 - %

CLload capacitance - - 200 pF

RLload resistance 1 - - k

tssettling time [1] 0.4 

Product data sheet Rev. 1.3 — 10 January 2020 136 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

13. Application information

13.1 LCD panel signal usage

Table 41. LCD panel connections for STN single panel mode

External pin 4-bit mono STN single panel 8-bit mono STN single panel Color STN single panel

LPC43xx pin

used

LCD function LPC43xx pin

used

LCD function LPC43xx pin

used

LCD function

LCD_VD[23:8] - - - - - -

LCD_VD7 - - P8_4 UD[7] P8_4 UD[7]

LCD_VD6 - - P8_5 UD[6] P8_5 UD[6]

LCD_VD5 - - P8_6 UD[5] P8_6 UD[5]

LCD_VD4 - - P8_7 UD[4] P8_7 UD[4]

LCD_VD3 P4_2 UD[3] P4_2 UD[3] P4_2 UD[3]

LCD_VD2 P4_3 UD[2] P4_3 UD[2] P4_3 UD[2]

LCD_VD1 P4_4 UD[1] P4_4 UD[1] P4_4 UD[1]

LCD_VD0 P4_1 UD[0] P4_1 UD[0] P4_1 UD[0]

LCD_LP P7_6 LCDLP P7_6 LCDLP P7_6 LCDLP

LCD_ENAB/

LCDM

P4_6 LCDENAB/

LCDM

P4_6 LCDENAB/

LCDM

P4_6 LCDENAB/

LCDM

LCD_FP P4_5 LCDFP P4_5 LCDFP P4_5 LCDFP

LCD_DCLK P4_7 LCDDCLK P4_7 LCDDCLK P4_7 LCDDCLK

LCD_LE P7_0 LCDLE P7_0 LCDLE P7_0 LCDLE

LCD_PWR P7_7 CDPWR P7_7 LCDPWR P7_7 LCDPWR

GP_CLKIN PF_4 LCDCLKIN PF_4 LCDCLKIN PF_4 LCDCLKIN

Table 42. LCD panel connections for STN dual panel mode

External pin 4-bit mono STN dual panel 8-bit mono STN dual panel Color STN dual panel

LPC43xx pin

used

LCD function LPC43xx pin

used

LCD function LPC43xx pin

used

LCD function

LCD_VD[23:16] - - - - - -

LCD_VD15 - - PB_4 LD[7] PB_4 LD[7]

LCD_VD14 - - PB_5 LD[6] PB_5 LD[6]

LCD_VD13 - - PB_6 LD[5] PB_6 LD[5]

LCD_VD12 - - P8_3 LD[4] P8_3 LD[4]

LCD_VD11 P4_9 LD[3] P4_9 LD[3] P4_9 LD[3]

LCD_VD10 P4_10 LD[2] P4_10 LD[2] P4_10 LD[2]

LCD_VD9 P4_8 LD[1] P4_8 LD[1] P4_8 LD[1]

LCD_VD8 P7_5 LD[0] P7_5 LD[0] P7_5 LD[0]

LCD_VD7 - - UD[7] P8_4 UD[7]

LCD_VD6 - - P8_5 UD[6] P8_5 UD[6]

LCD_VD5 - - P8_6 UD[5] P8_6 UD[5]

LCD_VD4 - - P8_7 UD[4] P8_7 UD[4]

LCD_VD3 P4_2 UD[3] P4_2 UD[3] P4_2 UD[3]

Product data sheet Rev. 1.3 — 10 January 2020 137 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

LCD_VD2 P4_3 UD[2] P4_3 UD[2] P4_3 UD[2]

LCD_VD1 P4_4 UD[1] P4_4 UD[1] P4_4 UD[1]

LCD_VD0 P4_1 UD[0] P4_1 UD[0] P4_1 UD[0]

LCD_LP P7_6 LCDLP P7_6 LCDLP P7_6 LCDLP

LCD_ENAB/

LCDM

P4_6 LCDENAB/

LCDM

P4_6 LCDENAB/

LCDM

P4_6 LCDENAB/

LCDM

LCD_FP P4_5 LCDFP P4_5 LCDFP P4_5 LCDFP

LCD_DCLK P4_7 LCDDCLK P4_7 LCDDCLK P4_7 LCDDCLK

LCD_LE P7_0 LCDLE P7_0 LCDLE P7_0 LCDLE

LCD_PWR P7_7 LCDPWR P7_7 LCDPWR P7_7 LCDPWR

GP_CLKIN PF_4 LCDCLKIN PF_4 LCDCLKIN PF_4 LCDCLKIN

Table 42. LCD panel connections for STN dual panel mode

External pin 4-bit mono STN dual panel 8-bit mono STN dual panel Color STN dual panel

LPC43xx pin

used

LCD function LPC43xx pin

used

LCD function LPC43xx pin

used

LCD function

Table 43. LCD panel connections for TFT panels

External

TFT 12 bit (4:4:4

mode)

TFT 16 bit (5:6:5 mode) TFT 16 bit (1:5:5:5 mode) TFT 24 bit

LPC43xx

pin used

LCD

function

LPC43xx

pin used

LCD

function

LPC43xx pin

used

LCD

function

LPC43xx

pin used

LCD

function

LCD_VD23 PB_0 BLUE3 PB_0 BLUE4 PB_0 BLUE4 PB_0 BLUE7

LCD_VD22 PB_1 BLUE2 PB_1 BLUE3 PB_1 BLUE3 PB_1 BLUE6

LCD_VD21 PB_2 BLUE1 PB_2 BLUE2 PB_2 BLUE2 PB_2 BLUE5

LCD_VD20 PB_3 BLUE0 PB_3 BLUE1 PB_3 BLUE1 PB_3 BLUE4

LCD_VD19 - - P7_1 BLUE0 P7_1 BLUE0 P7_1 BLUE3

LCD_VD18 - - - - P7_2 intensity P7_2 BLUE2

LCD_VD17 - - - - - - P7_3 BLUE1

LCD_VD16 - - - - - - P7_4 BLUE0

LCD_VD15 PB_4 GREEN3 PB_4 GREEN5 PB_4 GREEN4 PB_4 GREEN7

LCD_VD14 PB_5 GREEN2 PB_5 GREEN4 PB_5 GREEN3 PB_5 GREEN6

LCD_VD13 PB_6 GREEN1 PB_6 GREEN3 PB_6 GREEN2 PB_6 GREEN5

LCD_VD12 P8_3 GREEN0 P8_3 GREEN2 P8_3 GREEN1 P8_3 GREEN4

LCD_VD11 - - P4_9 GREEN1 P4_9 GREEN0 P4_9 GREEN3

LCD_VD10 - - P4_10 GREEN0 P4_10 intensity P4_10 GREEN2

LCD_VD9 - - - - - - P4_8 GREEN1

LCD_VD8 - - - - - - P7_5 GREEN0

LCD_VD7 P8_4 RED3 P8_4 RED4 P8_4 RED4 P8_4 RED7

LCD_VD6 P8_5 RED2 P8_5 RED3 P8_5 RED3 P8_5 RED6

LCD_VD5 P8_6 RED1 P8_6 RED2 P8_6 RED2 P8_6 RED5

LCD_VD4 P8_7 RED0 P8_7 RED1 P8_7 RED1 P8_7 RED4

LCD_VD3 - - P4_2 RED0 P4_2 RED0 P4_2 RED3

LCD_VD2 - - - - P4_3 intensity P4_3 RED2

LCD_VD1 - - - - - - P4_4 RED1

Product data sheet Rev. 1.3 — 10 January 2020 138 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

13.2 Crystal oscillator

The crystal oscillator is controlled by the XTAL_OSC_CTRL register in the CGU (see

LPC43xx/LPC43Sxx user manual).

The crystal oscillator operates at frequencies of 1 MHz to 25 MHz. This frequency can be

boosted to a higher frequency, up to the maximum CPU operating frequency, by the PLL.

The oscillator can operate in one of two modes: slave mode and oscillation mode.

•In slave mode, couple the input clock signal with a capacitor of 100 pF (CC in

Figure 42), with an amplitude of at least 200 mV (RMS). The XTAL2 pin in this

configuration can be left unconnected.

•External components and models used in oscillation mode are shown in Figure 43,

and in Table 44 and Table 45. Since the feedback resistance is integrated on chip,

only a crystal and the capacitances CX1 and CX2 need to be connected externally in

case of fundamental mode oscillation (L, CL and RS represent the fundamental

frequency). Capacitance CP in Figure 43 represents the parallel package capacitance

and must not be larger than 7 pF. Parameters FC, CL, RS and CP are supplied by the

crystal manufacturer.

LCD_VD0 - - - - - - P4_1 RED0

LCD_LP P7_6 LCDLP P7_6 LCDLP P7_6 LCDLP P7_6 LCDLP

LCD_ENAB

/LCDM

P4_6 LCDENAB/

LCDM

P4_6 LCDENAB/

LCDM

P4_6 LCDENAB/

LCDM

P4_6 LCDENAB/

LCDM

LCD_FP P4_5 LCDFP P4_5 LCDFP P4_5 LCDFP P4_5 LCDFP

LCD_DCLK P4_7 LCDDCLK P4_7 LCDDCLK P4_7 LCDDCLK P4_7 LCDDCLK

LCD_LE P7_0 LCDLE P7_0 LCDLE P7_0 LCDLE P7_0 LCDLE

LCD_PWR P7_7 LCDPWR P7_7 LCDPWR P7_7 LCDPWR P7_7 LCDPWR

GP_CLKIN PF_4 LCDCLKIN PF_4 LCDCLKIN PF_4 LCDCLKIN PF_4 LCDCLKIN

Table 43. LCD panel connections for TFT panels

External

TFT 12 bit (4:4:4

mode)

TFT 16 bit (5:6:5 mode) TFT 16 bit (1:5:5:5 mode) TFT 24 bit

LPC43xx

pin used

LCD

function

LPC43xx

pin used

LCD

function

LPC43xx pin

used

LCD

function

LPC43xx

pin used

LCD

function

Table 44. Recommended values for CX1/X2 in oscillation mode (crystal and external

components parameters) low frequency mode

Fundamental oscillation

frequency

Maximum crystal series

resistance RS

External load capacitors

CX1, CX2

2 MHz < 200 33 pF, 33 pF

< 200 39 pF, 39 pF

< 200 56 pF, 56 pF

4 MHz < 200 18 pF, 18 pF

< 200 39 pF, 39 pF

< 200 56 pF, 56 pF

8 MHz < 200 18 pF, 18 pF

< 200 39 pF, 39 pF

Product data sheet Rev. 1.3 — 10 January 2020 139 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

12 MHz < 160 18 pF, 18 pF

< 160 39 pF, 39 pF

16 MHz < 120 18 pF, 18 pF

< 80 33 pF, 33 pF

20 MHz < 100 18 pF, 18 pF

< 80 33 pF, 33 pF

Table 45. Recommended values for CX1/X2 in oscillation mode (crystal and external

components parameters) high frequency mode

Fundamental oscillation

frequency

Maximum crystal series

resistance RS

External load capacitors CX1,

CX2

15 MHz < 80 18 pF, 18 pF

20 MHz < 80 39 pF, 39 pF

< 100 47 pF, 47 pF

Fig 42. Slave mode operation of the on-chip oscillator

Fig 43. Oscillator modes with external crystal model used for CX1/CX2 evaluation

Table 44. Recommended values for CX1/X2 in oscillation mode (crystal and external

components parameters) low frequency mode

Fundamental oscillation

frequency

Maximum crystal series

resistance RS

External load capacitors

CX1, CX2

LPC43xx

XTAL1

100 pF

002aag379

002aag380

LPC43xx

XTAL1 XTAL2

CX2

CX1

XTAL

=CLCP

Product data sheet Rev. 1.3 — 10 January 2020 140 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

13.3 RTC oscillator

In the RTC oscillator circuit, only the crystal (XTAL) and the capacitances CRTCX1 and

CRTCX2 need to be connected externally. Typical capacitance values for CRTCX1 and

CRTCX2 are CRTCX1/2 = 20 (typical)  4 pF.

An external clock can be connected to RTCX1 if RTCX2 is left open. The recommended

amplitude of the clock signal is Vi(RMS) = 100 mV to 200 mV with a coupling capacitance of

5 pF to 10 pF.

13.4 XTAL and RTCX Printed Circuit Board (PCB) layout guidelines

Connect the crystal on the PCB as close as possible to the oscillator input and output pins

of the chip. Take care that the load capacitors CX1, CX2, and CX3 in case of third overtone

crystal usage have a common ground plane. Also connect the external components to the

ground plain. To keep the noise coupled in via the PCB as small as possible, make loops

and parasitics as small as possible. Choose smaller values of CX1 and CX2 if parasitics

increase in the PCB layout.

Ensure that no high-speed or high-drive signals are near the RTCX1/2 signals.

13.5 Standard I/O pin configuration

Figure 45 shows the possible pin modes for standard I/O pins with analog input function:

•Digital output driver enabled/disabled

•Digital input: Pull-up enabled/disabled

•Digital input: Pull-down enabled/disabled

•Digital input: Repeater mode enabled/disabled

•Digital input: Input buffer enabled/disabled

•Analog input

The default configuration for standard I/O pins is input buffer disabled and pull-up

enabled. The weak MOS devices provide a drive capability equivalent to pull-up and

pull-down resistors.

Fig 44. RTC 32 kHz oscillator circuit

002aah083

LPC43xx

RTCX1 RTCX2

CRTCX2

CRTCX1

XTAL

Product data sheet Rev. 1.3 — 10 January 2020 141 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

13.5.1 Reset pin configuration

13.5.2 Suggested USB interface solutions

The USB device can be connected to the USB as self-powered device (see Figure 47) or

bus-powered device (see Figure 48).

The glitch filter rejects pulses of typical 12 ns width.

Fig 45. Standard I/O pin configuration with analog input

slew rate bit EHS

pull-up enable bit EPUN

pull-down enable bit EPD

glitch

filter

analog I/O

ESD

VDDIO

VSSIO

input buffer enable bit EZI

filter select bit ZIF

data input to core

data output from core

enable output driver

002aah028

Fig 46. Reset pin configuration

VSS

reset

002aag702

Vps

Rpu ESD

ESD

20 ns RC

GLITCH FILTER PIN

Product data sheet Rev. 1.3 — 10 January 2020 142 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

On the LPC436x, USBn_VBUS pins are 5 V tolerant only when VDDIO is applied and at

operating voltage level. Therefore, if the USBn_VBUS function is connected to the USB

connector and the device is self-powered, the USBn_VBUS pins must be protected for

situations when VDDIO = 0 V.

If VDDIO is always at operating level while VBUS = 5 V, the USBn_VBUS pin can be

connected directly to the VBUS pin on the USB connector.

For systems where VDDIO can be 0 V and VBUS is directly applied to the USBn_VBUS

pins, precautions must be taken to reduce the voltage to below 3.6 V, which is the

maximum allowable voltage on the USBn_VBUS pins in this case.

One method is to use a voltage divider to connect the USBn_VBUS pins to VBUS on the

USB connector. The voltage divider ratio should be such that the USB_VBUS pin will be

greater than 0.7VDDIO to indicate a logic HIGH while below the 3.6 V allowable maximum

voltage.

For the following operating conditions

VBUSmax = 5.25 V

VDDIO = 3.6 V,

the voltage divider should provide a reduction of 3.6 V/5.25 V or ~0.686.

For bus-powered devices, a regulator powered by USB can provide 3.3 V to VDDIO

whenever bus power is present and ensure that power to the USBn_VBUS pins is always

present when the 5 V VBUS signal is applied. See Figure 48.

Remark: Applying 5 V to the USBn_VBUS pins for a short time while the regulator ramps

up might compromise the long-term reliability of the part but does not affect its function.

Fig 47. USB interface on a self-powered device where USBn_VBUS = 5 V

LPC43xx

VDDIO

USB-B

connector

USBn_VBUS VBUS

USB

aaa-013458

Product data sheet Rev. 1.3 — 10 January 2020 143 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

Remark: If the VBUS function of the USB1 interface is not connected, configure the pin

function for GPIO using the function control bits in the SYSCON block.

Remark: In OTG mode, it is important to be able to detect the VBUS level and to charge

and discharge VBUS. This requires adding active devices that disconnect the link when

VDDIO is not present.

Fig 48. USB interface on a bus-powered device

Fig 49. USB interface for USB operating in OTG mode

REGULATOR

VBUSUSBn_VBUS

LPC43xx

VDDIO

USB-B

connector

USB

aaa-013459

VBUS

USBn_VBUS

LPC43xx

VDDIO

USB-B

connector

USB

aaa-013460

Product data sheet Rev. 1.3 — 10 January 2020 144 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

14. Package outline

Fig 50. Package outline LBGA256 package

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC

MO-192

JEITA

- - - - - -

SOT740-2

05-06-16

05-08-04

UNIT A

max

mm 1.55 0.45

0.35 1.1

0.9 0.55

0.45 17.2

16.8 17.2

16.8

DIMENSIONS (mm are the original dimensions)

LBGA256: plastic low profile ball grid array package; 256 balls; body 17 x 17 x 1 mm

A2b D E e

0.25

0.1

0.12

0.35

1/2 e

AA2

detail X

ball A1

index area

y1C

2 4 6 8 10 12 14 16

1 3 5 7 9 11 13 15

ball A1

index area

∅ vM

∅ wM

05 10 mm

scale

Product data sheet Rev. 1.3 — 10 January 2020 145 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

Fig 51. Package outline of the LQFP208 package

UNIT A1A2A3bpcE

(1) eH

ELL

pZywv θ

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC JEITA

mm 0.15

0.05 1.45

1.35 0.25 0.27

0.17 0.20

0.09 28.1

27.9 0.5 30.15

29.85 1.43

1.08 7

0.080.121 0.08

DIMENSIONS (mm are the original dimensions)

Note

1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.

0.75

0.45

SOT459-1 136E30 MS-026 00-02-06

03-02-20

D(1)

28.1

27.9

30.15

29.85

1.43

1.08

pin 1 index

EA1

detail X L

(A )

HA2

vMB

vMA

208

157

156 105

104

0 5 10 mm

scale

LQFP208; plastic low profile quad flat package; 208 leads; body 28 x 28 x 1.4 mm SOT459-1

max.

1.6

Product data sheet Rev. 1.3 — 10 January 2020 146 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

Fig 52. Package outline of the TFBGA100 package

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC JEITA

SOT926-1 - - - - - - - - -

SOT926-1

05-12-09

05-12-22

UNIT A

max

mm 1.2 0.4

0.3 0.8

0.65 0.5

0.4 9.1

8.9 9.1

8.9

DIMENSIONS (mm are the original dimensions)

TFBGA100: plastic thin fine-pitch ball grid array package; 100 balls; body 9 x 9 x 0.7 mm

A2b D E e2

7.2

0.8

7.2

0.15

0.05

0.08

0.1

0 2.5 5 mm

scale

1/2 e

AC B

∅ vMC∅ wM

ball A1

index area

24681013579

ball A1

index area

B A

detail X

Product data sheet Rev. 1.3 — 10 January 2020 147 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

15. Soldering

Fig 53. Reflow soldering of the LBGA256 package

DIMENSIONS in mm

PSLSPSRHxHy

SOT740-2

solder land plus solder paste

occupied area

Footprint information for reflow soldering of LBGA256 package

solder land

solder paste deposit

solder resist

Generic footprint pattern

Refer to the package outline drawing for actual layout

detail X

see detail X

sot740-2_fr

1.00 0.450 0.450 0.600 17.500 17.500

Product data sheet Rev. 1.3 — 10 January 2020 148 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

Fig 54. Reflow soldering of the LQFP208 package

SOT459-1

DIMENSIONS in mm

occupied area

Footprint information for reflow soldering of LQFP208 package

AyBy

P1P2

D2 (8×) D1

(0.125)

Ax Ay Bx By D1 D2 Gx Gy Hx HyP1 P2 C

sot459-1_fr

solder land

Generic footprint pattern

Refer to the package outline drawing for actual layout

31.300 31.300 28.300 28.3000.500 0.560 0.2801.500 0.400 28.500 28.500 31.550 31.550

Product data sheet Rev. 1.3 — 10 January 2020 149 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

Fig 55. Reflow soldering of the TFBGA100 package

DIMENSIONS in mm

PSLSPSRHxHy

SOT926-1

solder land plus solder paste

occupied area

Footprint information for reflow soldering of TFBGA100 package

solder land

solder paste deposit

solder resist

Generic footprint pattern

Refer to the package outline drawing for actual layout

detail X

see detail X

sot926-1_fr

0.80 0.330 0.400 0.480 9.400 9.400

Product data sheet Rev. 1.3 — 10 January 2020 150 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

16. Abbreviations

Table 46. Abbreviations

Acronym Description

ADC Analog-to-Digital Converter

AHB Advanced High-performance Bus

APB Advanced Peripheral Bus

API Application Programming Interface

BOD BrownOut Detection

CAN Controller Area Network

CMAC Cipher-based Message Authentication Code

CSMA/CD Carrier Sense Multiple Access with Collision Detection

DAC Digital-to-Analog Converter

DC-DC Direct Current-to-Direct Current

DMA Direct Memory Access

GPIO General Purpose Input/Output

IRC Internal RC

IrDA Infrared Data Association

JTAG Joint Test Action Group

LCD Liquid Crystal Display

LSB Least Significant Bit

MAC Media Access Control

MCU MicroController Unit

MIIM Media Independent Interface Management

n.c. not connected

OHCI Open Host Controller Interface

OTG On-The-Go

PHY Physical Layer

PLL Phase-Locked Loop

PMC Power Mode Control

PWM Pulse Width Modulator

RIT Repetitive Interrupt Timer

RMII Reduced Media Independent Interface

SDRAM Synchronous Dynamic Random Access Memory

SIMD Single Instruction Multiple Data

SPI Serial Peripheral Interface

SSI Serial Synchronous Interface

SSP Synchronous Serial Port

UART Universal Asynchronous Receiver/Transmitter

ULPI UTMI+ Low Pin Interface

USART Universal Synchronous Asynchronous Receiver/Transmitter

USB Universal Serial Bus

UTMI USB2.0 Transceiver Macrocell Interface

Product data sheet Rev. 1.3 — 10 January 2020 151 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

17. References

[1] LPC43xx/LPC43Sxx User manual UM10503:

http://www.nxp.com/documents/user_manual/UM10503.pdf

[2] LPC43xx Errata sheet:

http://www.nxp.com/documents/errata_sheet/ES_LPC43XX.pdf

Product data sheet Rev. 1.3 — 10 January 2020 152 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

18. Revision history

Table 47. Revision history

Document ID Release date Data sheet status Change notice Supersedes

LPC436x v.1.3 20200110 Product data sheet - LPC436x v.1.2

•Updated for rise and fall times for I/O pins configured as input only.

LPC436x v.1.2 20160304 Product data sheet - LPC436x v.1.1

•Updated Table 32 “Dynamic characteristics: Dynamic external memory interface”:

Read cycle parameters th(D) min value is 2.2 ns and max value is “-”.

•Fixed the number of ADC channels for LPC4367JET100 in Table 2 “Ordering options”

to 4.

LPC436x v.1.1 <tbd> Product data sheet 2015110041 LPC436x v.1.0

Modifications: •Added CIN number, 2015110041 for SSP timing value changes in the change notice

column of the Revision history table.

•Updated Table 27 “Dynamic characteristics: SSP pins in SPI mode”:

–changed units of Tcy(clk), clock cycle time, SSP slave and master from ns to s.

–removed tv(Q), data output valid time in SPI mode, minimum value of 3 ´ (1/PCLK)

from SSP slave mode.

–added units to td, delay time, for SSP slave and master mode.

LPC436x v.1.0 <tbd> Product data sheet - -

Product data sheet Rev. 1.3 — 10 January 2020 153 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

19. Legal information

19.1 Data sheet status

[1] Please consult the most recently issued document before initiating or completing a design.

[2] The term ‘short data sheet’ is explained in section “Definitions”.

[3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status

information is available on the Internet at URL http://www.nxp.com.

19.2 Definitions

Draft — The document is a draft version only. The content is still under

internal review and subject to formal approval, which may result in

modifications or additions. NXP Semiconductors does not give any

representations or warranties as to the accuracy or completeness of

information included herein and shall have no liability for the consequences of

use of such information.

Short data sheet — A short data sheet is an extract from a full data sheet

with the same product type number(s) and title. A short data sheet is intended

for quick reference only and should not be relied upon to contain detailed and

full information. For detailed and full information see the relevant full data

sheet, which is available on request via the local NXP Semiconductors sales

office. In case of any inconsistency or conflict with the short data sheet, the

full data sheet shall prevail.

Product specification — The information and data provided in a Product

data sheet shall define the specification of the product as agreed between

NXP Semiconductors and its customer, unless NXP Semiconductors and

customer have explicitly agreed otherwise in writing. In no event however,

shall an agreement be valid in which the NXP Semiconductors product is

deemed to offer functions and qualities beyond those described in the

Product data sheet.

19.3 Disclaimers

Limited warranty and liability — Information in this document is believed to

be accurate and reliable. However, NXP Semiconductors does not give any

representations or warranties, expressed or implied, as to the accuracy or

completeness of such information and shall have no liability for the

consequences of use of such information. NXP Semiconductors takes no

responsibility for the content in this document if provided by an information

source outside of NXP Semiconductors.

In no event shall NXP Semiconductors be liable for any indirect, incidental,

punitive, special or consequential damages (including - without limitation - lost

profits, lost savings, business interruption, costs related to the removal or

replacement of any products or rework charges) whether or not such

damages are based on tort (including negligence), warranty, breach of

contract or any other legal theory.

Notwithstanding any damages that customer might incur for any reason

whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards

customer for the products described herein shall be limited in accordance

with the Terms and conditions of commercial sale of NXP Semiconductors.

Right to make changes — NXP Semiconductors reserves the right to make

changes to information published in this document, including without

limitation specifications and product descriptions, at any time and without

notice. This document supersedes and replaces all information supplied prior

to the publication hereof.

Suitability for use — NXP Semiconductors products are not designed,

authorized or warranted to be suitable for use in life support, life-critical or

safety-critical systems or equipment, nor in applications where failure or

malfunction of an NXP Semiconductors product can reasonably be expected

to result in personal injury, death or severe property or environmental

damage. NXP Semiconductors and its suppliers accept no liability for

inclusion and/or use of NXP Semiconductors products in such equipment or

applications and therefore such inclusion and/or use is at the customer’s own

risk.

Applications — Applications that are described herein for any of these

products are for illustrative purposes only. NXP Semiconductors makes no

representation or warranty that such applications will be suitable for the

specified use without further testing or modification.

Customers are responsible for the design and operation of their applications

and products using NXP Semiconductors products, and NXP Semiconductors

accepts no liability for any assistance with applications or customer product

design. It is customer’s sole responsibility to determine whether the NXP

Semiconductors product is suitable and fit for the customer’s applications and

products planned, as well as for the planned application and use of

customer’s third party customer(s). Customers should provide appropriate

design and operating safeguards to minimize the risks associated with their

applications and products.

NXP Semiconductors does not accept any liability related to any default,

damage, costs or problem which is based on any weakness or default in the

customer’s applications or products, or the application or use by customer’s

third party customer(s). Customer is responsible for doing all necessary

testing for the customer’s applications and products using NXP

Semiconductors products in order to avoid a default of the applications and

the products or of the application or use by customer’s third party

customer(s). NXP does not accept any liability in this respect.

Limiting values — Stress above one or more limiting values (as defined in

the Absolute Maximum Ratings System of IEC 60134) will cause permanent

damage to the device. Limiting values are stress ratings only and (proper)

operation of the device at these or any other conditions above those given in

the Recommended operating conditions section (if present) or the

Characteristics sections of this document is not warranted. Constant or

repeated exposure to limiting values will permanently and irreversibly affect

the quality and reliability of the device.

Terms and conditions of commercial sale — NXP Semiconductors

products are sold subject to the general terms and conditions of commercial

sale, as published at http://www.nxp.com/profile/terms, unless otherwise

agreed in a valid written individual agreement. In case an individual

agreement is concluded only the terms and conditions of the respective

agreement shall apply. NXP Semiconductors hereby expressly objects to

applying the customer’s general terms and conditions with regard to the

purchase of NXP Semiconductors products by customer.

No offer to sell or license — Nothing in this document may be interpreted or

construed as an offer to sell products that is open for acceptance or the grant,

conveyance or implication of any license under any copyrights, patents or

other industrial or intellectual property rights.

Document status[1][2] Product status[3] Definition

Objective [short] data sheet Development This document contains data from the objective specification for product development.

Preliminary [short] data sheet Qualification This document contains data from the preliminary specification.

Product [short] data sheet Production This document contains the product specification.

Product data sheet Rev. 1.3 — 10 January 2020 154 of 156

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

Export control — This document as well as the item(s) described herein

may be subject to export control regulations. Export might require a prior

authorization from competent authorities.

Non-automotive qualified products — Unless this data sheet expressly

states that this specific NXP Semiconductors product is automotive qualified,

the product is not suitable for automotive use. It is neither qualified nor tested

in accordance with automotive testing or application requirements. NXP

Semiconductors accepts no liability for inclusion and/or use of

non-automotive qualified products in automotive equipment or applications.

In the event that customer uses the product for design-in and use in

automotive applications to automotive specifications and standards, customer

(a) shall use the product without NXP Semiconductors’ warranty of the

product for such automotive applications, use and specifications, and (b)

whenever customer uses the product for automotive applications beyond

NXP Semiconductors’ specifications such use shall be solely at customer’s

own risk, and (c) customer fully indemnifies NXP Semiconductors for any

liability, damages or failed product claims resulting from customer design and

use of the product for automotive applications beyond NXP Semiconductors’

standard warranty and NXP Semiconductors’ product specifications.

19.4 Trademarks

Notice: All referenced brands, product names, service names and trademarks

are the property of their respective owners.

I2C-bus — logo is a trademark of NXP B.V.

20. Contact information

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: salesaddresses@nxp.com

Product data sheet Rev. 1.3 — 10 January 2020 155 of 156

continued >>

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

21. Contents

1 General description . . . . . . . . . . . . . . . . . . . . . . 1

2 Features and benefits . . . . . . . . . . . . . . . . . . . . 1

3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4 Ordering information . . . . . . . . . . . . . . . . . . . . . 5

4.1 Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 5

5 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 6

6 Pinning information . . . . . . . . . . . . . . . . . . . . . . 7

6.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

6.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 8

7 Functional description . . . . . . . . . . . . . . . . . . 60

7.1 Architectural overview. . . . . . . . . . . . . . . . . . . 60

7.2 ARM Cortex-M4 processor . . . . . . . . . . . . . . . 60

7.3 ARM Cortex-M0 processors . . . . . . . . . . . . . . 60

7.3.1 ARM Cortex-M0 coprocessor . . . . . . . . . . . . . 60

7.3.2 ARM Cortex-M0 subsystem . . . . . . . . . . . . . . 60

7.4 Interprocessor communication . . . . . . . . . . . . 61

7.5 AHB multilayer matrix . . . . . . . . . . . . . . . . . . . 62

7.6 Nested Vectored Interrupt Controller (NVIC) . 63

7.6.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

7.6.2 Interrupt sources. . . . . . . . . . . . . . . . . . . . . . . 63

7.7 System Tick timer (SysTick) . . . . . . . . . . . . . . 63

7.8 Event router . . . . . . . . . . . . . . . . . . . . . . . . . . 63

7.9 Global Input Multiplexer Array (GIMA) . . . . . . 64

7.9.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

7.10 On-chip static RAM. . . . . . . . . . . . . . . . . . . . . 64

7.11 On-chip flash memory. . . . . . . . . . . . . . . . . . . 64

7.12 EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

7.13 Boot ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

7.14 Memory mapping . . . . . . . . . . . . . . . . . . . . . . 66

7.15 One-Time Programmable (OTP) memory. . . . 69

7.16 General Purpose I/O (GPIO) . . . . . . . . . . . . . 69

7.16.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

7.17 Configurable digital peripherals . . . . . . . . . . . 69

7.17.1 SCTimer/PWM . . . . . . . . . . . . . . . . . . . . . . . . 69

7.17.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

7.17.2 Serial GPIO (SGPIO) . . . . . . . . . . . . . . . . . . . 70

7.17.2.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

7.18 AHB peripherals . . . . . . . . . . . . . . . . . . . . . . . 71

7.18.1 General Purpose DMA . . . . . . . . . . . . . . . . . . 71

7.18.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

7.18.2 SPI Flash Interface (SPIFI). . . . . . . . . . . . . . . 71

7.18.2.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

7.18.3 SD/MMC card interface . . . . . . . . . . . . . . . . . 72

7.18.4 External Memory Controller (EMC). . . . . . . . . 72

7.18.4.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

7.18.5 High-speed USB Host/Device/OTG interface

(USB0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

7.18.5.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

7.18.6 High-speed USB Host/Device interface with ULPI

(USB1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

7.18.6.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

7.18.7 LCD controller . . . . . . . . . . . . . . . . . . . . . . . . 74

7.18.7.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

7.18.8 Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

7.18.8.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

7.19 Digital serial peripherals. . . . . . . . . . . . . . . . . 76

7.19.1 UART1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

7.19.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

7.19.2 USART0/2/3 . . . . . . . . . . . . . . . . . . . . . . . . . . 76

7.19.2.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

7.19.3 SPI serial I/O controller . . . . . . . . . . . . . . . . . 77

7.19.3.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

7.19.4 SSP serial I/O controller. . . . . . . . . . . . . . . . . 77

7.19.4.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

7.19.5 I2C-bus interface . . . . . . . . . . . . . . . . . . . . . . 78

7.19.5.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

7.19.6 I2S interface . . . . . . . . . . . . . . . . . . . . . . . . . . 78

7.19.6.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

7.19.7 C_CAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

7.19.7.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

7.20 Counter/timers and motor control. . . . . . . . . . 79

7.20.1 General purpose 32-bit timers/external event

counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

7.20.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

7.20.2 Motor control PWM . . . . . . . . . . . . . . . . . . . . 80

7.20.3 Quadrature Encoder Interface (QEI) . . . . . . . 80

7.20.3.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

7.20.4 Repetitive Interrupt (RI) timer. . . . . . . . . . . . . 81

7.20.4.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

7.20.5 Windowed WatchDog Timer (WWDT) . . . . . . 81

7.20.5.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

7.21 Analog peripherals . . . . . . . . . . . . . . . . . . . . . 82

7.21.1 Analog-to-Digital Converter (ADC0/1) . . . . . . 82

7.21.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

7.21.2 Digital-to-Analog Converter (DAC). . . . . . . . . 82

7.21.2.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

7.22 Peripherals in the RTC power domain . . . . . . 82

7.22.1 RTC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

7.22.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

7.22.1.2 Event monitor/recorder. . . . . . . . . . . . . . . . . . 83

7.22.2 Alarm timer . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

7.23 System control . . . . . . . . . . . . . . . . . . . . . . . . 83

7.23.1 Configuration registers (CREG) . . . . . . . . . . . 83

7.23.2 System Control Unit (SCU) . . . . . . . . . . . . . . 84

7.23.3 Clock Generation Unit (CGU). . . . . . . . . . . . . 84

NXP Semiconductors LPC436x

32-bit ARM Cortex-M4/M0 microcontroller

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: salesaddresses@nxp.com

Date of release: 10 January 2020

Document identifier: LPC436X

Please be aware that important notices concerning this document and the product(s)

described herein, have been included in section ‘Legal information’.

7.23.4 Internal RC oscillator (IRC). . . . . . . . . . . . . . . 84

7.23.5 PLL0USB (for USB0) . . . . . . . . . . . . . . . . . . . 84

7.23.6 PLL0AUDIO (for audio). . . . . . . . . . . . . . . . . . 84

7.23.7 System PLL1 . . . . . . . . . . . . . . . . . . . . . . . . . 85

7.23.8 Reset Generation Unit (RGU). . . . . . . . . . . . . 85

7.23.9 Power Management Controller (PMC) . . . . . . 85

7.23.10 Power control . . . . . . . . . . . . . . . . . . . . . . . . . 86

7.23.11 Code security (Code Read Protection - CRP) 87

7.24 Serial Wire Debug/JTAG. . . . . . . . . . . . . . . . . 87

8 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 89

9 Thermal characteristics. . . . . . . . . . . . . . . . . . 90

10 Static characteristics. . . . . . . . . . . . . . . . . . . . 91

10.1 Power consumption . . . . . . . . . . . . . . . . . . . . 98

10.2 Peripheral power consumption . . . . . . . . . . . 101

10.3 Electrical pin characteristics . . . . . . . . . . . . . 103

10.4 BOD and band gap static characteristics . . . 107

11 Dynamic characteristics . . . . . . . . . . . . . . . . 108

11.1 Flash/EEPROM memory . . . . . . . . . . . . . . . 108

11.2 Wake-up times . . . . . . . . . . . . . . . . . . . . . . . 109

11.3 External clock for oscillator in slave mode . . 109

11.4 Crystal oscillator . . . . . . . . . . . . . . . . . . . . . . 110

11.5 IRC oscillator . . . . . . . . . . . . . . . . . . . . . . . . 110

11.6 RTC oscillator . . . . . . . . . . . . . . . . . . . . . . . . 110

11.7 GPCLKIN . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

11.8 I/O pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

11.9 I2C-bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

11.10 I2S-bus interface . . . . . . . . . . . . . . . . . . . . . . 113

11.11 USART interface. . . . . . . . . . . . . . . . . . . . . . 114

11.12 SSP interface . . . . . . . . . . . . . . . . . . . . . . . . 116

11.13 SPI interface . . . . . . . . . . . . . . . . . . . . . . . . . 119

11.14 SSP/SPI timing diagrams . . . . . . . . . . . . . . . 120

11.15 SPIFI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

11.16 SGPIO timing . . . . . . . . . . . . . . . . . . . . . . . . 122

11.17 External memory interface . . . . . . . . . . . . . . 124

11.18 USB interface . . . . . . . . . . . . . . . . . . . . . . . . 129

11.19 Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

11.20 SD/MMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132

11.21 LCD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132

12 ADC/DAC electrical characteristics . . . . . . . 133

13 Application information. . . . . . . . . . . . . . . . . 136

13.1 LCD panel signal usage . . . . . . . . . . . . . . . . 136

13.2 Crystal oscillator . . . . . . . . . . . . . . . . . . . . . . 138

13.3 RTC oscillator . . . . . . . . . . . . . . . . . . . . . . . . 140

13.4 XTAL and RTCX Printed Circuit Board (PCB)

layout guidelines . . . . . . . . . . . . . . . . . . . . . . 140

13.5 Standard I/O pin configuration . . . . . . . . . . . 140

13.5.1 Reset pin configuration . . . . . . . . . . . . . . . . . 141

13.5.2 Suggested USB interface solutions . . . . . . . 141

14 Package outline . . . . . . . . . . . . . . . . . . . . . . . 144

15 Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

16 Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . 150

17 References . . . . . . . . . . . . . . . . . . . . . . . . . . . 151

18 Revision history . . . . . . . . . . . . . . . . . . . . . . 152

19 Legal information . . . . . . . . . . . . . . . . . . . . . 153

19.1 Data sheet status . . . . . . . . . . . . . . . . . . . . . 153

19.2 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . 153

19.3 Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . 153

19.4 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . 154

20 Contact information . . . . . . . . . . . . . . . . . . . 154

21 Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155