Data Sheet July 11, 2011 Naos Raptor 20A: Non-Isolated Power Modules 4.5 - 14Vdc input; 0.59Vdc to 6Vdc Output; 20A Output Current Features RoHS Compliant Applications Compliant to RoHS EU Directive 2002/95/EC (Z versions) Compatible in a Pb-free or SnPb wave-soldering environment (Z versions) Wide input voltage range (4.5Vdc-14Vdc) Tunable Loop response Fixed switching frequency Output overcurrent protection (non-latching) Over temperature protection Output voltage programmable from 0.59Vdc to 6Vdc via external resistor TM Distributed power architectures Remote On/Off Intermediate bus voltage applications Remote Sense Telecommunications equipment Servers and storage applications Networking equipment to optimize dynamic output voltage Power Good Signal Small size: 36.8 mm x 15.5 mm x 9.2 mm (1.45 in. x 0.61 in. x 0.36 in) Wide operating temperature range (-40C to 85C) ISO** 9001 and ISO 14001 certified manufacturing facilities UL* 60950 Recognized, CSA C22.2 No. 60950-00 Certified, and VDE 0805 (EN60950-1 3rd edition) Licensed Description The Naos Raptor 20A SIP power modules are non-isolated dc-dc converters in an industry standard package that can deliver up to 20A of output current with a full load efficiency of 91% at 3.3Vdc output voltage (VIN = 12Vdc). These modules operate over a wide range of input voltage (VIN = 4.5Vdc-13.8Vdc) and provide a precisely regulated output voltage from 0.59Vdc to 6Vdc, programmable via an external resistor. Features include remote On/Off, adjustable output voltage, over current and over temperature protection. A new feature, the Tunable LoopTM, allows the user to optimize the dynamic response of the converter to match the load. * UL is a registered trademark of Underwriters Laboratories, Inc. CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. ** ISO is a registered trademark of the International Organization of Standards Document No: DS06-127 ver. 1.11 PDF name: NSR020A0X_ds.pdf Data Sheet July 11, 2011 Naos Raptor 20A: Non Isolated Power Module: 4.5 - 14Vdc input; 0.59Vdc to 6Vdc Output; 20A output current Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min Max Unit Input Voltage Continuous Operating Ambient Temperature All VIN -0.3 15 Vdc All TA -40 85 C All Tstg -55 125 C (see Thermal Considerations section) Storage Temperature Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min Typ Max Unit Operating Input Voltage All VIN 4.5 12.0 13.8 Vdc Maximum Input Current All IIN,max 20 Adc VO,set = 0.6 Vdc IIN,No load 50 mA VO,set = 5.0Vdc IIN,No load 110 mA All IIN,stand-by 6.08 mA Inrush Transient All It Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 1H source impedance; VIN, min to VIN, max, IO= IOmax ; See Test configuration section) All 34.4 Input Ripple Rejection (120Hz) All 43 (VIN= VIN, min to VIN, max, IO=IO, max VO,set = 3.3Vdc) Input No Load Current (VIN = 12Vdc, IO = 0, module ON) Input Stand-by Current (VIN = 12Vdc, module disabled) LINEAGE POWER 2 1 2 As mAp-p dB 2 Data Sheet July 11, 2011 Naos Raptor 20A: Non Isolated Power Module: 4.5 - 14Vdc input; 0.59Vdc to 6Vdc Output; 20A output current Electrical Specifications (continued) Parameter Device Symbol Min Output Voltage Set-point (with 0.5% tolerance for external resistor used to set output voltage) All VO, set -1.5 Output Voltage All VO, set -3.0 All VO 0.59 Typ Max Unit +1.5 % VO, set +3.0 % VO, set 6 Vdc (Over all operating input voltage, resistive load, and temperature conditions until end of life) Adjustment Range Selected by an external resistor Output Regulation (for VO 2.5V) Line (VIN=VIN, min to VIN, max) All Load (IO=IO, min to IO, max All -0.2 +0.2 % VO, set 0.8 % VO, set +5 mV 20 mV Output Regulation (for VO < 2.5V) Line (VIN=VIN, min to VIN, max) All Load (IO=IO, min to IO, max) All -5 Output Ripple and Noise on nominal output (VIN=VIN, nom and IO=IO, min to IO, max, Cout = 0F) Peak-to-Peak (5Hz to 20MHz bandwidth) Vo = 0.59V 20 mVpk-pk Peak-to-Peak (5Hz to 20MHz bandwidth) Vo = 1.2V 23 mVpk-pk Peak-to-Peak (5Hz to 20MHz bandwidth) Vo = 1.8V 25 mVpk-pk Peak-to-Peak (5Hz to 20MHz bandwidth) Vo = 2.5V 30 mVpk-pk Peak-to-Peak (5Hz to 20MHz bandwidth) Vo = 3.3V 40 mVpk-pk Peak-to-Peak (5Hz to 20MHz bandwidth) Vo = 5.0V 50 mVpk-pk Peak-to-Peak (5Hz to 20MHz bandwidth) Vo = 6.0V 60 mVpk-pk 300 F External Capacitance 1 TM Without the Tunable Loop All CO, max ESR 0.15 m All CO, max 0 1500 F ESR 10 m All CO, max 0 10000 F 0 20 ESR 1 m With the Tunable Loop TM Output Current All Io Output Current Limit Inception (Hiccup Mode ) All IO, lim 140 % Io Adc Output Short-Circuit Current All IO, s/c 1.1 Arms VO,set = 0.59Vdc 72.7 % VO,set = 1.2Vdc 82.3 % (VO250mV) ( Hiccup Mode ) Efficiency (Vin=9Vdc) VIN= 12Vdc, TA=25C IO=IO, max , VO= VO,set Switching Frequency 1 VO,set = 1.8Vdc 87.5 % VO,set = 2.5Vdc 90.2 % VO,set = 3.3Vdc 92.1 % VO,set = 5.0Vdc 94.3 % VO,set = 6.0Vdc All fsw 95.0 600 % kHz TM External capacitors may require using the new Tunable Loop feature to ensure that the module is stable as well as TM getting the best transient response. See the Tunable Loop section for details. LINEAGE POWER 3 Data Sheet July 11, 2011 Naos Raptor 20A: Non Isolated Power Module: 4.5 - 14Vdc input; 0.59Vdc to 6Vdc Output; 20A output current General Specifications Parameter Min Calculated MTBF (VIN=12V, VO=5Vdc, IO=0.8IO, max, TA=40C) Per Telcordia Issue 2, Method I Case 3 Max Unit 16,061,773 Weight Typ Hours 6.6 (0.23) g (oz.) Feature Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See Feature Descriptions for additional information. Parameter Device Symbol Min Typ Max Unit On/Off Signal Interface (VIN=VIN, min to VIN, max ; open collector or equivalent, Signal referenced to GND) Logic High (On/Off pin open - Module ON) Input High Current All IIH 0 0.5 mA Input High Voltage All VIH 1.0 5.5 V Logic Low (Module OFF) Input Low Current All IIL 200 A Input Low Voltage All VIL -0.3 0.4 V PwGood (Power Good) Signal Interface Open Collector/Drain PwGood = High = Power Good PwGood = Low = Power Not Good Logic level low voltage, Isink = 5 mA 0 Sink Current, PwGood = low 0.35 V 10 mA Turn-On Delay and Rise Times (VIN=VIN, nom, IO=IO, max , VO to within 1% of steady state) Case 1: On/Off input is enabled and then input power is applied (delay from instant at which VIN = VIN, min until Vo = 10% of Vo, set) All Tdelay 2 3 msec Case 2: Input power is applied for at least one second and then the On/Off input is enabled (delay from instant at which On/Off is enabled until Vo = 10% of Vo, set) All Tdelay 2 3 msec Output voltage Rise time (time for Vo to rise from 10% of Vo, set to 90% of Vo, set) All Trise 3 6 msec 0.5 % VO, set Output voltage overshoot o IO = IO, max; VIN, min - VIN, max, TA = 25 C Remote Sense Range All Over Temperature Protection All Tref 0.5 V 130 C (See Thermal Considerations section) Input Undervoltage Lockout Turn-on Threshold All 4.2 Vdc Turn-off Threshold All 4.1 Vdc LINEAGE POWER 4 Data Sheet July 11, 2011 Naos Raptor 20A: Non Isolated Power Module: 4.5 - 14Vdc input; 0.59Vdc to 6Vdc Output; 20A output current Characteristic Curves The following figures provide typical characteristics for the Naos Raptor 20A modules at 0.6Vout and 25C. 22 90 20 OUTPUT CURRENT, Io (A) EFFICIENCY, (%) 85 80 Vin = 6V 75 Vin = 9V Vin = 4.5V 70 65 60 0 5 10 15 20 LINEAGE POWER 1m/s (200LFM) 1.5m/s (300LFM) 10 NC 0.5m/s (100LFM) 8 25 35 45 55 65 75 85 OUTPUT VOLTAGE VO (V) (200mV/div) IO (A) (5Adiv) OUTPUT CURRENT, TIME, t (100s /div) VIN (V) (5V/div) VO (V) (200mV/div) Figure 4. Transient Response to Dynamic Load Change from 0% to 50% to 0% with VIN=9V. INPUT VOLTAGE VO (V) (200mV/div) Figure 5. Typical Start-up Using On/Off Voltage (Io = Io,max). 12 Figure 2. Derating Output Current versus Ambient Temperature and Airflow. OUTPUT VOLTAGE VO (V) (10mV/div) OUTPUT VOLTAGE ON/OFF VOLTAGE VON/OFF (V) (2V/div) OUTPUT VOLTAGE TIME, t (1ms/div) 2m/s (400LFM) 14 AMBIENT TEMPERATURE, TA C Figure 1. Converter Efficiency versus Output Current. TIME, t (1s/div) 16 O OUTPUT CURRENT, IO (A) Figure 3. Typical output ripple and noise (VIN = 9V, Io = Io,max). 18 TIME, t (1ms/div) Figure 6. Typical Start-up Using Input Voltage (VIN = 9V, Io = Io,max). 5 Data Sheet July 11, 2011 Naos Raptor 20A: Non Isolated Power Module: 4.5 - 14Vdc input; 0.59Vdc to 6Vdc Output; 20A output current Characteristic Curves (continued) The following figures provide typical characteristics for the Naos Raptor 20A modules at 1.2Vout and 25C. 22 95 20 OUTPUT CURRENT, Io (A) EFFICIENCY, (%) 90 Vin = 4.5V 85 Vin = 12V 80 Vin = 14V 75 70 0 5 10 15 0.5m/s (100LFM) NC 8 35 45 55 65 75 85 OUTPUT VOLTAGE VO (V) (200mV/div) IO (A) (5Adiv) OUTPUT CURRENT, TIME, t (20s /div) VIN (V) (5V/div) VO (V) (500mV/div) Figure 10. Transient Response to Dynamic Load Change from 0% to 50% to 0% with VIN=12V. INPUT VOLTAGE VON/OFF (V) (2V/div) VO (V) (500mV/div) LINEAGE POWER 1.5m/s (300LFM) 10 AMBIENT TEMPERATURE, TA C OUTPUT VOLTAGE VO (V) (10mV/div) OUTPUT VOLTAGE ON/OFF VOLTAGE OUTPUT VOLTAGE Figure 11. Typical Start-up Using On/Off Voltage (Io = Io,max). 1m/s (200LFM) 12 Figure 8. Derating Output Current versus Ambient Temperature and Airflow. Figure 7. Converter Efficiency versus Output Current. TIME, t (1ms/div) 2m/s (400LFM) 14 O OUTPUT CURRENT, IO (A) TIME, t (1s/div) 16 25 20 Figure 9. Typical output ripple and noise (VIN = 12V, Io = Io,max). 18 TIME, t (1ms/div) Figure 12. Typical Start-up Using Input Voltage (VIN = 12V, Io = Io,max). 6 Data Sheet July 11, 2011 Naos Raptor 20A: Non Isolated Power Module: 4.5 - 14Vdc input; 0.59Vdc to 6Vdc Output; 20A output current Characteristic Curves (continued) The following figures provide typical characteristics for the Naos Raptor 20A modules at 1.8Vout and at 25C. 22 100 20 OUTPUT CURRENT, Io (A) EFFICIENCY, (%) 95 90 Vin = 12V 85 Vin = 14V Vin = 4.5V 80 75 70 0 5 10 15 LINEAGE POWER 1m/s (200LFM) 10 0.5m/s (100LFM) NC 8 35 45 55 65 75 85 AMBIENT TEMPERATURE, TA C OUTPUT VOLTAGE VO (V) (200mV/div) IO (A) (5Adiv) OUTPUT CURRENT, TIME, t (100s /div) VIN (V) (5V/div) VO (V) (500mV/div) Figure 16. Transient Response to Dynamic Load Change from 0% to 50% to 0% with VIN=12V. INPUT VOLTAGE VON/OFF (V) (2V/div) VO (V) (500mV/div) Figure 17. Typical Start-up Using On/Off Voltage (Io = Io,max). 1.5m/s (300LFM) 12 Figure 14. Derating Output Current versus Ambient Temperature and Airflow. OUTPUT VOLTAGE VO (V) (10mV/div) OUTPUT VOLTAGE ON/OFF VOLTAGE OUTPUT VOLTAGE TIME, t (1ms/div) 2m/s (400LFM) 14 O Figure 13. Converter Efficiency versus Output Current. TIME, t (1s/div) 16 25 20 OUTPUT CURRENT, IO (A) Figure 15. Typical output ripple and noise (VIN = 12V, Io = Io,max). 18 TIME, t (1ms/div) Figure 18. Typical Start-up Using Input Voltage (VIN = 12V, Io = Io,max). 7 Data Sheet July 11, 2011 Naos Raptor 20A: Non Isolated Power Module: 4.5 - 14Vdc input; 0.59Vdc to 6Vdc Output; 20A output current Characteristic Curves (continued) The following figures provide thermal derating curves for Naos Raptor 20A modules at 2.5Vout and 25C. 22 100 20 OUTPUT CURRENT, Io (A) EFFICIENCY, (%) 95 90 Vin = 12V 85 Vin = 14V Vin = 4.5V 80 75 70 0 5 10 15 LINEAGE POWER 1m/s (200LFM) 0.5m/s (100LFM) 10 NC 8 35 45 55 65 75 85 AMBIENT TEMPERATURE, TA C OUTPUT VOLTAGE VO (V) (200mV/div) IO (A) (5Adiv) OUTPUT CURRENT, TIME, t (100s /div) VIN (V) (5V/div) VO (V) (1V/div) Figure 22. Transient Response to Dynamic Load Change from 0% to 50% to 0% with VIN=12V. INPUT VOLTAGE VON/OFF (V) (2V/div) VO (V) (1V/div) Figure 23. Typical Start-up Using On/Off Voltage (Io = Io,max). 1.5m/s (300LFM) 12 Figure 20. Derating Output Current versus Ambient Temperature and Airflow. OUTPUT VOLTAGE VO (V) (10mV/div) OUTPUT VOLTAGE ON/OFF VOLTAGE OUTPUT VOLTAGE TIME, t (1ms/div) 2m/s (400LFM) 14 O Figure 19. Converter Efficiency versus Output Current. Figure 21. Typical output ripple and noise (VIN = 12V, Io = Io,max). 16 25 20 OUTPUT CURRENT, IO (A) TIME, t (1s/div) 18 TIME, t (1ms/div) Figure 24. Typical Start-up Using Input Voltage (VIN = 12V, Io = Io,max). 8 Data Sheet July 11, 2011 Naos Raptor 20A: Non Isolated Power Module: 4.5 - 14Vdc input; 0.59Vdc to 6Vdc Output; 20A output current Characteristic Curves (continued) The following figures provide thermal derating curves for Naos Raptor 20A modules at 3.3Vout and 25C. 100 22 OUTPUT CURRENT, Io (A) 20 EFFICIENCY, (%) 95 90 Vin = 4.5V Vin = 12V Vin = 14V 85 80 0 5 10 15 LINEAGE POWER 1.5m/s (300LFM) 12 1m/s (200LFM) 0.5m/s (100LFM) 10 NC 8 35 45 55 65 75 85 IO (A) (5Adiv) OUTPUT VOLTAGE VO (V) (200mV/div) Figure 26. Derating Output Current versus Ambient Temperature and Airflow. TIME, t (100s /div) VIN (V) (5V/div) VO (V) (1V/div) INPUT VOLTAGE Figure 28. Transient Response to Dynamic Load Change from 0% to 50% to 0% with VIN=12V. OUTPUT VOLTAGE VON/OFF (V) (2V/div) VO (V) (1V/div) Figure 29. Typical Start-up Using On/Off Voltage (Io = Io,max). 14 AMBIENT TEMPERATURE, TA C OUTPUT CURRENT, VO (V) (10mV/div) OUTPUT VOLTAGE ON/OFF VOLTAGE OUTPUT VOLTAGE TIME, t (1ms/div) 2m/s (400LFM) O Figure 25. Converter Efficiency versus Output Current. Figure 27. Typical output ripple and noise (VIN = 12V, Io = Io,max). 16 25 20 OUTPUT CURRENT, IO (A) TIME, t (1s/div) 18 TIME, t (1ms/div) Figure 30. Typical Start-up Using Input Voltage (VIN = 12V, Io = Io,max). 9 Data Sheet July 11, 2011 Naos Raptor 20A: Non Isolated Power Module: 4.5 - 14Vdc input; 0.59Vdc to 6Vdc Output; 20A output current Characteristic Curves (continued) The following figures provide thermal derating curves for Naos Raptor 20A modules at 5Vout and 25C. 100 22 OUTPUT CURRENT, Io (A) 20 EFFICIENCY, (%) 95 Vin = 12V 90 Vin = 14V Vin = 6V 85 80 0 5 10 15 LINEAGE POWER 1m/s (200LFM) 0.5m/s (100LFM) 10 NC 8 35 45 55 65 75 85 AMBIENT TEMPERATURE, TA C OUTPUT VOLTAGE VO (V) (200mV/div) IO (A) (5Adiv) OUTPUT CURRENT, TIME, t (100s /div) VIN (V) (5V/div) VO (V) (2V/div) Figure 34. Transient Response to Dynamic Load Change from 0% to 50% to 0% with VIN=12V. INPUT VOLTAGE VON/OFF (V) (2V/div) VO (V) (2V/div) Figure 35. Typical Start-up Using On/Off Voltage (Io = Io,max). 1.5m/s (300LFM) 12 Figure 32. Derating Output Current versus Ambient Temperature and Airflow. OUTPUT VOLTAGE VO (V) (10mV/div) OUTPUT VOLTAGE ON/OFF VOLTAGE OUTPUT VOLTAGE TIME, t (1ms/div) 2m/s (400LFM) 14 O Figure 31. Converter Efficiency versus Output Current. TIME, t (1s/div) 16 25 20 OUTPUT CURRENT, IO (A) Figure 33. Typical output ripple and noise (VIN = 12V, Io = Io,max). 18 TIME, t (1ms/div) Figure 36. Typical Start-up Using Input Voltage (VIN = 12V, Io = Io,max). 10 Data Sheet July 11, 2011 Naos Raptor 20A: Non Isolated Power Module: 4.5 - 14Vdc input; 0.59Vdc to 6Vdc Output; 20A output current Characteristic Curves (continued) The following figures provide thermal derating curves for Naos Raptor 20A modules at 6Vout and 25C. 22 100 OUTPUT CURRENT, Io (A) 20 EFFICIENCY, (%) 95 Vin = 12V 90 Vin = 14V Vin = 7.5V 85 80 0 5 10 15 LINEAGE POWER 1m/s (200LFM) 0.5m/s (100LFM) 10 NC 8 35 45 55 65 75 85 OUTPUT VOLTAGE VO (V) (200mV/div) IO (A) (5Adiv) TIME, t (100s /div) VO (V) (2V/div) VIN (V) (5V/div) Figure 40. Transient Response to Dynamic Load Change from 0% to 50% to 0% with VIN=12V. INPUT VOLTAGE Figure 41. Typical Start-up Using On/Off Voltage (Io = Io,max). 12 Figure 38. Derating Output Current versus Ambient Temperature and Airflow. OUTPUT VOLTAGE VON/OFF (V) (2V/div) VO (V) (2V/div) TIME, t (1ms/div) 1.5m/s (300LFM) AMBIENT TEMPERATURE, TA C OUTPUT CURRENT, VO (V) (10mV/div) OUTPUT VOLTAGE ON/OFF VOLTAGE OUTPUT VOLTAGE Figure 39. Typical output ripple and noise (VIN = 12V, Io = Io,max). 14 O OUTPUT CURRENT, IO (A) TIME, t (1s/div) 2m/s (400LFM) 16 25 20 Figure 37. Converter Efficiency versus Output Current. 18 TIME, t (1ms/div) Figure 42. Typical Start-up Using Input Voltage (VIN = 12V, Io = Io,max). 11 Data Sheet July 11, 2011 Naos Raptor 20A: Non Isolated Power Module: 4.5 - 14Vdc input; 0.59Vdc to 6Vdc Output; 20A output current Test Configurations Design Considerations CURRENT PROBE The Naos Raptor 20A module should be connected to a low-impedance source. A highly inductive source can affect the stability of the module. An input capacitance must be placed directly adjacent to the input pin of the module, to minimize input ripple voltage and ensure module stability. To minimize input voltage ripple, low-ESR ceramic or polymer capacitors are recommended at the input of the module. Figure 46 shows the input ripple voltage for various output voltages at 20A of load current with 2x22 F or 4x22 F ceramic capacitors and an input of 12V. LTEST VIN(+) BATTERY 1H CIN CS 1000F Electrolytic 2x100F Tantalum E.S.R.<0.1 @ 20C 100kHz COM NOTE: Measure input reflected ripple current with a simulated source inductance (LTEST) of 1H. Capacitor CS offsets possible battery impedance. Measure current as shown above. 90 Figure 43. Input Reflected Ripple Current Test Setup. COPPER STRIP VO (+) RESISTIVE LOAD 1uF . 10uF Input Filtering SCOPE COM GROUND PLANE Input Ripple Voltage (mVp-p) TO OSCILLOSCOPE 80 2x22uF 70 4x22uF 60 50 40 30 20 10 0 0.5 1 1.5 NOTE: All voltage measurements to be taken at the module terminals, as shown above. If sockets are used then Kelvin connections are required at the module terminals to avoid measurement errors due to socket contact resistance. Figure 44. Output Ripple and Noise Test Setup. Rdistribution Rcontact Rcontact VIN(+) 2 2.5 3 3.5 4 4.5 5 Output Voltage (Vdc) Figure 46. Input ripple voltage for various output voltages with 2x22 F or 4x22 F ceramic capacitors at the input (20A load). Input voltage is 12V. Rdistribution VO Output Filtering Rdistribution RLOAD VO VIN Rcontact Rcontact COM Rdistribution COM NOTE: All voltage measurements to be taken at the module terminals, as shown above. If sockets are used then Kelvin connections are required at the module terminals to avoid measurement errors due to socket contact resistance. Figure 45. Output Voltage and Efficiency Test Setup. VO. IO Efficiency = LINEAGE POWER VIN. IIN x 100 % The Naos Raptor 20A modules are designed for low output ripple voltage and will meet the maximum output ripple specification with no external capacitors. However, additional output filtering may be required by the system designer for a number of reasons. First, there may be a need to further reduce the output ripple and noise of the module. Second, the dynamic response characteristics may need to be customized to a particular load step change. To reduce the output ripple and improve the dynamic response to a step load change, additional capacitance at the output can be used. Low ESR ceramic and polymer are recommended to improve the dynamic response of the module. For stable operation of the module, limit the capacitance to less than the maximum output capacitance as specified in the electrical specification table. Optimal performance of the module can be achieved by using the Tunable LoopTM feature described later in this data sheet. 12 Data Sheet July 11, 2011 Naos Raptor 20A: Non Isolated Power Module: 4.5 - 14Vdc input; 0.59Vdc to 6Vdc Output; 20A output current Safety Considerations Feature Descriptions For safety agency approval the power module must be installed in compliance with the spacing and separation requirements of the end-use safety agency standards, i.e., UL 60950-1, CSA C22.2 No. 60950-1-03, and VDE 0850:2001-12 (EN60950-1) Licensed. For the converter output to be considered meeting the requirements of safety extra-low voltage (SELV), the input must meet SELV requirements. The power module has extra-low voltage (ELV) outputs when all inputs are ELV. An input fuse for the module is recommended. Due to the wide input voltage and output voltage ranges of the module, different fuse ratings are recommended as shown in Table 1. These are suggested "maximum" fuse ratings. However, for optimum circuit protection, the fuse value should not be any larger than required in the end application. As an option to using a fuse, no fuse is required, if the module is 1. powered by a power source with current limit protection set point less than the protection device value listed in Table 1, and 2. the module is evaluated in the end-use equipment. Table 1. Remote On/Off Input Output Voltage (VDC) Voltage 0.59 to 1.3 1.31 to 2.7 2.71 to 5.0 5.1 to 6 (VDC) 10.1 to 14 5A 10A 15A 20A 6.51 to 10 6.3A 15A 25A 30A 4.5 to 6.5 10A 20A 30A NA The Naos Raptor 20A modules feature an On/Off pin with positive logic for remote On/Off operation. If not using the On/Off pin, leave the pin open (the module will be ON, except for the -49 option modules where leaving the pin open will cause the module to remain OFF). The On/Off signal (VOn/Off) is referenced to ground. During a Logic High on the On/Off pin, the module remains ON. During Logic-Low, the module is turned OFF. MODULE R1 7.5K ON/OFF ENABLE R2 100k C1 1000p GND Figure 47. Remote On/Off Implementation. Components R2 and C1 are only present in the -49Z option module. Overcurrent Protection To provide protection in a fault (output overload) condition, the unit is equipped with internal current-limiting circuitry and can endure current limiting continuously. At the point of current-limit inception, the unit enters hiccup mode. The unit operates normally once the output current is brought back into its specified range. The typical average output current during hiccup is 10% of Io,max. Overtemperature Protection To provide protection in a fault condition, these modules are equipped with a thermal shutdown circuit. The unit will shut down if the overtemperature threshold of 130C is exceeded at the thermal reference point Tref. The thermal shutdown is not intended as a guarantee that the unit will survive temperatures beyond its rating. Once the unit goes into thermal shutdown it will then wait to cool before attempting to restart. Input Undervoltage Lockout At input voltages below the input undervoltage lockout limit, module operation is disabled. The module will begin to operate at an input voltage above the undervoltage lockout turn-on threshold. LINEAGE POWER 13 Data Sheet July 11, 2011 Naos Raptor 20A: Non Isolated Power Module: 4.5 - 14Vdc input; 0.59Vdc to 6Vdc Output; 20A output current Table 2 provides Rtrim values required for some common output voltages. Feature Descriptions (continued) Power Good Table 2 The Naos Raptor 20A modules provide a Power Good Status signal that indicates whether or not the power module is functioning properly. PwGood is a power good signal implemented with an open-collector output to indicate that the output voltage is within the regulation limits of the power module. The PwGood signal will be de-asserted to a low state If any condition such as over-temperature, over-current, or over-voltage occurs which would result in the output voltage going out of range. Output Voltage Programming The output voltage of the Naos Raptor 20A module can be programmed to any voltage from 0.59Vdc to 6Vdc by connecting a resistor between the Trim+ and Trim- pins of the module. Certain restrictions apply on the output voltage set point depending on the input voltage. These are shown in the Output Voltage vs. Input Voltage Set Point Area plot in Fig. 48. The Upper Limit curve shows that for output voltages of 0.9V and lower, the input voltage must be lower than the maximum of 14V. The Lower Limit curve shows that for output voltages of 3.8V and higher, the input voltage needs to be larger than the minimum of 4.5V. VO, set (V) Rtrim (K) 0.59 1.0 1.2 1.5 1.8 2.5 3.3 5.0 6.0 Open 2.89 1.941 1.3 0.978 0.619 0.436 0.268 0.219 By using a 0.5% tolerance trim resistor with a TC of 25ppm, a set point tolerance of 1.5% can be achieved as specified in the electrical specification. The POL Programming Tool available at www.lineagepower.com under the Design Tools section, helps determine the required trim resistor needed for a specific output voltage. Note: Vin 130% of Vout at the module output pin. V IN(+) V O(+) ON/OFF TRIM+ Vout 16 Input Voltage (v) 14 12 10 LOAD R trim 8 GND 6 TRIM- 4 2 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 Figure 49. Circuit configuration for programming output voltage using an external resistor. Output Voltage (V) Figure 48. Output Voltage vs. Input Voltage Set Point Area plot showing limits where the output voltage can be set for different input voltages. Without an external resistor between Trim+ and Trim- pins, the output of the module will be 0.59Vdc. To calculate the value of the trim resistor, Rtrim for a desired output voltage, use the following equation: Rtrim = 1.182 k (Vo - 0.591) Rtrim is the external resistor in k Vo is the desired output voltage LINEAGE POWER Voltage Margining Output voltage margining can be implemented in the Naos Raptor 20A modules by connecting a resistor, Rmargin-up, from the Trim+ pin to the Trim- pin for margining-up the output voltage and by connecting a resistor, Rmargin-down, from the Trim+ pin to the output pin for margining-down. Figure 50 shows the circuit configuration for output voltage margining. The POL Programming Tool, available at www.lineagepower.com under the Design Tools section, also calculates the values of Rmargin-up and Rmargin-down for a specific output voltage and % margin. Please consult your local Lineage Power technical representative for additional details. 14 Data Sheet July 11, 2011 Naos Raptor 20A: Non Isolated Power Module: 4.5 - 14Vdc input; 0.59Vdc to 6Vdc Output; 20A output current Vo Rmargin-down MODULE Q2 Trim+ for an input voltage of 12V. The value of RTUNE should never be lower than the values shown in Tables 3 and 4. Please contact your Lineage Power technical representative to obtain more details of this feature as well as for guidelines on how to select the right value of external R-C to tune the module for best transient performance and stable operation for other output capacitance values. Rmargin-up VOUT SENSE+ Rtrim RTune Q1 MODULE Trim- CTune TRIM+ Figure 50. Circuit Configuration for margining Output voltage. RTrim TRIM- Monotonic Start-up and Shutdown The Naos Raptor 20A modules have monotonic start-up and shutdown behavior for any combination of rated input voltage, output current and operating temperature range. TM Tunable Loop The Naos Raptor 20A modules have a new feature that optimizes transient response of the module called TM Tunable Loop . External capacitors are usually added to improve output voltage transient response due to load current changes. Sensitive loads may also require additional output capacitance to reduce output ripple and noise. Adding external capacitance however affects the voltage control loop of the module, typically causing the loop to slow down with sluggish response. Larger values of external capacitance could also cause the module to become unstable. To use the additional external capacitors in an optimal TM manner, the Tunable Loop feature allows the loop to be tuned externally by connecting a series R-C between the SENSE and TRIM pins of the module, as shown in Fig. 51. This R-C allows the user to externally adjust the voltage loop feedback compensation of the module to match the filter network connected to the output of the module. Figure. 51. Circuit diagram showing connection of RTUME and CTUNE to tune the control loop of the module. Table 3. Recommended values of RTUNE and CTUNE to obtain transient deviation of 2% of Vout for a 10A step load with Vin=12V. Vout 5V 3.3V 2.5V 1.8V 1.2V 0.69V 4x47F 2x47F 6x47F + + + 330F 7x330F 23x330F Cext Polymer 330F 2x330F 3x330F Polymer Polymer Polymer Polymer Polymer RTUNE 75 51 51 51 51 31 CTUNE 100nF 150nF 220nF 330nF 330nF 330nF V 94mV 66mV 50mV 36mV 24mV 12mV Table 4. General recommended values of of RTUNE and CTUNE for Vin=12V and various external ceramic capacitor combinations. Cext 2x47F 4x47F 6x47F 10x47F 20x47F 30x47F RTUNE 75 75 75 51 51 51 CTUNE 15nF 27nF 33nF 47nF 68nF 82nF Recommended values of RTUNE and CTUNE are given in Tables 3 and 4. Table 3 lists recommended values of RTUNE and CTUNE in order to meet 2% output voltage deviation limits for some common output voltages in the presence of a 5A to 10A step change (50% of full load), with an input voltage of 12V. Table 4 shows the recommended values of RTUNE and CTUNE for different values of ceramic output capacitors up to 1000uF, again LINEAGE POWER 15 Data Sheet July 11, 2011 Naos Raptor 20A: Non Isolated Power Module: 4.5 - 14Vdc input; 0.59Vdc to 6Vdc Output; 20A output current Thermal Considerations Power modules operate in a variety of thermal environments; however sufficient cooling should always be provided to help ensure reliable operation. Considerations include ambient temperature, airflow, module power dissipation, and the need for increased reliability. A reduction in the operating temperature of the module will result in an increase in reliability. The thermal data presented here is based on physical measurements taken in a wind tunnel. The test set-up is shown in Figure 52. The preferred airflow direction for the module is in Figure 53. Figure 53. Temperature measurement location Tref. Wind Tunnel 50.8 [2.00] PWBs Heat Transfer via Convection Power Module 76.2 [3.0] 7.24 [0.285] Probe Location for measuring airflow and ambient temperature Air Flow Figure 52. Thermal Test Set-up. The thermal reference point, Tref used in the specifications is shown in Figure 53. For reliable o operation this temperatures should not exceed 122 C. The output power of the module should not exceed the rated power of the module (Vo,set x Io,max). Please refer to the Application Note "Thermal Characterization Process For Open-Frame BoardMounted Power Modules" for a detailed discussion of thermal aspects including maximum device temperatures. LINEAGE POWER Increased airflow over the module enhances the heat transfer via convection. Thermal derating curves showing the maximum output current that can be delivered at different local ambient temperatures (TA) for airflow conditions ranging from natural convection and up to 2m/s (400 ft./min) are shown in the Characteristics Curves section. Post solder Cleaning and Drying Considerations Post solder cleaning is usually the final circuit-board assembly process prior to electrical board testing. The result of inadequate cleaning and drying can affect both the reliability of a power module and the testability of the finished circuit-board assembly. For guidance on appropriate soldering, cleaning and drying procedures, refer to Board Mounted Power Modules: Soldering and Cleaning Application Note. Through-Hole Lead-Free Soldering Information These RoHS-compliant through-hole products use the SAC (Sn/Ag/Cu) Pb-free solder and RoHS-compliant components. They are designed to be processed through single or dual wave soldering machines. The pins have an RoHS-compliant finish that is compatible with both Pb and Pb-free wave soldering processes. A maximum preheat rate of 3C/s is suggested. The wave preheat process should be such that the temperature of the power module board is kept below 210C. For Pb solder, the recommended pot temperature is 260C, while the Pb-free solder pot is 270C max. Not all RoHScompliant through-hole products can be processed with paste-through-hole Pb or Pb-free reflow process. If additional information is needed, please consult with your Lineage Power technical representative for more details. 16 Data Sheet July 11, 2011 Naos Raptor 20A: Non Isolated Power Module: 4.5 - 14Vdc input; 0.59Vdc to 6Vdc Output; 20A output current Mechanical Outline Dimensions are in inches and (millimeters). Tolerances: x.x mm 0.5 mm (x.xx in. 0.02 in.) [unless otherwise indicated] x.xx mm 0.25 mm (x.xxx in 0.010 in.) Front View L = 3.30 0.5 [ 0.13 0.02] Side View Pin Pin out LINEAGE POWER Function Pin Function 1 Vout 6 Vin 2 Trim + 7 Sense + 3 GND 8 Sense - 4 PwGood 9 TRIM - 5 On/Off 10 GND 17 Data Sheet July 11, 2011 Naos Raptor 20A: Non Isolated Power Module: 4.5 - 14Vdc input; 0.59Vdc to 6Vdc Output; 20A output current Recommended Pad Layout Dimensions are in millimeters and (inches). Tolerances: x.x mm 0.2 mm (x.xx in. 0.02 in.) [unless otherwise indicated] x.xx mm 0.12 mm (x.xxx in 0.005 in.) LINEAGE POWER Pin Function Pin 1 Vout 6 Function Vin 2 Trim + 7 Sense + 3 GND 8 Sense - 4 PwGood 9 TRIM - 5 On/Off 10 GND 18 Data Sheet July 11, 2011 Naos Raptor 20A: Non Isolated Power Module: 4.5 - 14Vdc input; 0.59Vdc to 6Vdc Output; 20A output current Ordering Information Please contact your Lineage Power Sales Representative for pricing, availability and optional features. Table 5. Device Codes Device Code Input Voltage Range Output Voltage Output Current On/Off Logic Connector Type Comcode NSR020A0X43Z 4.5 - 13.8Vdc 0.59 - 6Vdc 20 A Positive SIP CC109130911 Pin Length On/Off logic Sense 4 3 Table 6. Coding Scheme Series generation Output Current Output voltage NSR 020A0 X 020A0=20A X= programmable output Blank = Standard 4 = positive 3 = Remote No entry = Sense negative Blank=without Default On/Off Condition ROHS Compliance Z Blank=Standard, ON when unconnected Z = ROHS6 5=5.1mm 2=Inverted On/Off 6=3.7mm 8=2.8mm Asia-Pacific Headquarters Tel: +86.021.54279977*808 World Wide Headquarters Lineage Power Corporation 601 Shiloh Road, Plano, TX 75074, USA +1-888-LINEAGE(546-3243) (Outside U.S.A.: +1-972-244-WATT(9288)) www.lineagepower.com e-mail: techsupport1@lineagepower.com Europe, Middle-East and Africa Headquarters Tel: +49.89.878067-280 India Headquarters Tel: +91.80.28411633 Lineage Power reserves the right to make changes to the product(s) or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Lineage Power DC-DC products are protected under various patents. Information on these patents is available at www.lineagepower.com/patents. (c) 2011 Lineage Power Corporation, (Plano, Texas) All International Rights Reserved. LINEAGE POWER 19 Document No: DS06-127 ver. 1.11 PDF name: NSR020A0X_ds.pdf