www.RFM.com E-mail: info@rfm.com Page 1 of 2
©2008 by RF Monolithics, Inc. RO3101A-1 - 3/26/08
Electrical Characteristics
Characteristic Sym Notes Minimum Typical Maximum Units
Center Frequency (+25 °C) Absolute Frequency fC2,3,4,5 433.870 433.970 MHz
Tolerance from 433.920 MHz ΔfC±50 kHz
Insertion Loss IL 2,5,6 1.5 2.2 dB
Quality Factor Unloaded Q QU5,6,7 9000
50 Ω Loaded Q QL1458
Temperature Stability Turnover Temperature TO6,7,8 10 25 40 °C
Turnover Frequency fOfC
Frequency Temperature Coefficient FTC 0.032 ppm/°C2
Frequency Aging Absolute Value during the First Year |fA|1≤10 ppm/yr
DC Insulation Resistance between Any Two Terminals 5 1.0 MΩ
RF Equivalent RLC Model Mot ional Resistance RM5, 7, 9 19.4 Ω
Motional Inductance LM63.8 µH
Motional Capacitance CM2.11 fF
Shunt Static Capacitance CO5, 6, 9 2.4 pF
Test Fixture Shunt Inductance LTEST 2, 7 55.1 nH
Lid Symbolization (in addition to Lot and/or Date Codes) 745 // YWWS
• Ideal for European 433.92 MHz Transmitters
• Very Low Series Resistance
• Quartz Stability
• Surface-Mount Ceramic Case
• Complies with Directive 2002/95/EC (RoHS)
The RO3101A-1 is a true one-port, surface-acoustic-wave (SAW) resonator in a surface-mount, ceramic case.
It provides reliable, fundamental-mode, quartz frequency stabilization of fixed-frequency transmitters
operating at 433.92 MHz. This SAW is designed specifically for remote-control and wireless security
transmitters operating in Europe under ETSI I-ETS 300 220 and in Germany under FTZ 17 TR 2100.
Absolute Maximum Ratings
Rating Value Units
CW RF Power Dissipation (See: Typical Test Circuit) +0 dBm
DC voltage Between Terminals (Observe ESD Precautions) ±30 VDC
Case Temperature -40 to +85 °C
Soldering Temperature (10 seconds / 5 cycles max.) 260 °C
433.92 MHz
SAW
Resonator
RO3101A-1
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
Notes:
1. Frequency aging is the change in fC with time and is specified at +65°C or
less. Aging may exceed the specification for prolonged temperatures
above +65°C. Typically, aging is greatest the first year after manufacture,
decreasing in subsequent years .
2. The center frequency, fC, is measured at the minimum insertion loss point,
ILMIN, with the res onator in the 50 Ω test system (VSWR ≤ 1.2:1). The
shunt inductance, LTEST, is tuned for parallel resonance with CO at fC.
Typi cally, fOSCILLATOR or fTRANSMITTER is approx imately equal to the
resonator fC.
3. One or more of the following United Sta tes patents apply: 4,454,488 and
4,616,197.
4. Typically, equipment utilizing this devic e requires emissions testing and
government app roval, which is the responsibility of the equipment
manufacturer.
5. Unless noted otherwis e, case temperature TC= +25°C±2°C.
6. The design, manufacturing process, and sp ecifications of this dev ice are
subject to change without notice.
7. Derived mat hematically from one or more of the following directly
measured parameters: fC, IL, 3 dB bandwidth, fC versus TC, and CO.
8. Turnover temperature, TO, is the temperatur e of maximum (or turnover)
frequenc y, fO. The nomina l frequenc y at an y case te mperature, TC, may be
calculated from: f = fO[1 - FTC (TO-TC)2]. Typically oscillator TO is
approximately equal to the spec ified resonator TO.
9. This equiv alent RLC model approximates resonator performance near the
resonan t frequen cy and is provided for refer ence o nly. The capaci tanc e CO
is the static (nonmotional) capacitance between the two terminals
measured at low frequency (10 MHz) with a capacitance meter. The
measureme nt includes p arasitic cap acitanc e with "NC” pads unconne cted.
Case pa r as itic capacitance is approx imately 0.05 pF. Tra nsducer parallel
capacitance can by calculated as: CP≈CO-0.05pF.
10. Tape and Reel standard per ANSI / EIA 481.
SM5035-4
Pb