M4TXX-BR12SH TIMEKEEPER SNAPHAT (Battery & Crystal) Provides Battery Backup Power for Non-Volatile TIMEKEEPERs and Controllers in the SNAPHAT SOIC Package Removable Battery Avoids Heat Associated with Surface Mount Process Snaps Directly onto Surface-Mounted SNAPHAT SOIC Choice of Battery Capacities - M4T28-BR12SH = 48 mAh - M4T32-BR12SH = 120 mAh Keyed Insertion to Insure Proper Assembly Removable for Replacement and Proper Disposal Available in Tubes or Tape & Reel For Use with the 28 and 44 pin SOIC Versions of the TIMEKEEPER Product Families DESCRIPTION The M4Txx-BR12SH SNAPHAT top is a detachable lithium power source for ST's non-volatile TIMEKEEPER surface mount SOIC (MH) package (28 and 44 pin). The SNAPHAT top contains both the battery and crystal and is designed to be "snapped on" after the SOIC is surface mounted on the PC board. Thus the two piece solution avoids the battery and crystal from having to be exposed to the high temperatures of the surface mount process. SNAPHAT (SH) Battery & Crystal Figure 1. Logic Diagram X1 X2 SNAPHAT VBAT- VBAT+ AI02528 November 1999 1/7 M4TXX-BR12SH MECHANICAL INFORMATION Electrical connection to the SOIC is made through four pins that connect to the four press fitted sockets at each end of the SOIC. Critical contact points between the pins and sockets are gold-plated to resist oxidation. Internally, each socket contains six independent contact fingers to form redundant connections between the two components. These sockets were designed with high point contact force to provide the lowest possible contact resistance. The SNAPHAT top also incorporates four molded-in retaining clips which hold onto the ends of the SOIC insuring mechanical and electrical connection even under severe mechanical shock and vibration. The combined SOIC and SNAPHAT assembly can sustain shock levels in excess of 100 g without separating. This package also passes variable frequency testing in accordance with MIL-STD-883, method 2007.2, condition A. Figure 2 illustrates the affect of repeated insertion and extraction of the SNAPHAT top to the SOIC. The force required to extract the SNAPHAT, and then to re-insert it, reduces each time. After three or four extractions, though, the reduction starts to become unnoticeable, and the force required remains at a fairly constant figure. Typically, though, the SNAPHAT will only need to be extracted and re-inserted once in its lifetime. BATTERY CHARACTERISTICS Figure 3 illustrates the lithium coin cell discharge rate for a given load. This demonstrates the char- Table 1. Description Parameter Value Operating Temperature 1 = 0 to 70 C 6 = -40 to 85 C Storage Temperature -40 to 85 C Nominal Crystal Frequency 32.768 kHz Load Capacitance 12.5 pF Nominal Battery Voltage 2.8 V Nominal Battery Capacity 48 mAh 120 mAh Battery Chemistry Li(CF)x M4T28 M4T32 acteristically flat voltage level supplied by the battery until very near the end of its life. These discharge levels have been greatly accelerated in comparison to the normal, actual usage. UL RECOGNITION The M4Txx-BR12SH has been recognized by Underwriters Laboratories under their Component Recognition Program and carries U.L. File Number E89556. Figure 2. SNAPHAT Insertion/Extraction Forces 20 7.5 Force (pounds) 5 Average Insertion Force Average Extraction Force 12.5 10 7.5 5 2.5 0 1 2 3 4 5 6 7 8 9 10 Number of Extractions AI02526 2/7 M4TXX-BR12SH Figure 3. Battery Discharge Rates LOAD CHARACTERISTICS 3.5 Temp: 20C Voltage (V) 3.0 2.5 2.0 15k 30k 100k 1.5 1.0 0 200 400 600 800 1000 1200 1400 1600 1800 2000 Duration (hrs.) (A) LOAD CHARACTERISTICS 3.5 Temp: 20C Voltage (V) 3.0 2.5 2.0 15k 30k 50k 100k 1.5 1.0 0 1000 2000 3000 4000 Duration (hrs.) (B) BATTERY LIFE For information on Data Retention Life and Battery Storage Life, please refer to the Application Note AN1012. 5000 6000 AI02519 Figure 4. DIP Extractor Tool GENERAL NOTES To remove the SNAPHAT top for replacement, a DIP/IC extractor tool should be used. Caution: To avoid draining battery do NOT place SNAPHAT pins in a conductive foam. Caution: To avoid damaging SNAPHAT sockets do NOT wave solder SOIC. AI02527 For battery disposal information, see on the web at www.rayovac.com. 3/7 M4TXX-BR12SH Table 2. Ordering Information Scheme Example: M4T28-BR12 SH 1 Product Family M4T = SNAPHAT Battery & Crystal Battery Voltage & Capacity 28-BR12 = BR1225, 3 V, 48 mAh 32-BR12 = BR1632, 3 V, 120 mAh Package SH = SNAPHAT Temperature Range 1 = 0 to 70 C 6 = -40 to 85 C For further information on any aspect of this device, please contact the STMicroelectronics Sales Office nearest to you. 4/7 M4TXX-BR12SH Table 3. M4T28-BR12SH - TIMEKEEPER 4-pin SNAPHAT Housing for 48 mAh Battery & Crystal, Package Mechanical Data mm inches Symb Typ Min A Max Typ Min Max 9.78 0.385 A1 6.73 7.24 0.265 0.285 A2 6.48 6.99 0.255 0.275 A3 0.38 0.015 B 0.46 0.56 0.018 0.022 D 21.21 21.84 0.835 0.860 E 14.22 14.99 0.560 0.590 eA 15.55 15.95 0.612 0.628 eB 3.20 3.61 0.126 0.142 L 2.03 2.29 0.080 0.090 Figure 5. M4T28-BR12SH - TIMEKEEPER 4-pin SNAPHAT Housing for 48 mAh Battery & Crystal, Package Outline A1 eA A2 A A3 B L eB D E SHTK-A Drawing is not to scale. 5/7 M4TXX-BR12SH Table 4. M4T32-BR12SH - TIMEKEEPER 4-pin SNAPHAT Housing for 120 mAh Battery & Crystal, Package Mechanical Data mm inches Symb Typ Min A Max Typ Min Max 10.54 0.415 A1 8.00 8.51 0.315 0.335 A2 7.24 8.00 0.285 0.315 A3 0.38 0.015 B 0.46 0.56 0.018 0.022 D 21.21 21.84 0.835 0.860 E 17.27 18.03 0.680 0.710 eA 15.55 15.95 0.612 0.628 eB 3.20 3.61 0.126 0.142 L 2.03 2.29 0.080 0.090 Figure 6. M4T32-BR12SH - TIMEKEEPER 4-pin SNAPHAT Housing for 120 mAh Battery & Crystal, Package Outline A1 eA A2 A A3 B L eB D E SHTK-A Drawing is not to scale. 6/7 M4TXX-BR12SH If you have any questions or suggestions concerning the matters raised in this document, please send them to the following electronic mail addresses: apps.nvram@st.com (for application support) ask.memory@st.com (for general enquiries) Please remember to include your name, company, location, telephone number and fax number. Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in lif e support devices or systems without express written approval of STMicroelectronics. The ST logo is registered trademark of STMicroelectronics 1999 STMicroelectronics - All Rights Reserved All other names are the property of their respective owners. STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A . http://w ww.st.com 7/7