ADC12H034CIMSAX/NOPB - NATIONAL SEMICONDUCTOR

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

www.ti.com

SNAS080K –JULY 1999–REVISED MARCH 2013

Self-Calibrating 12-Bit Plus Sign Serial I/O A/D Converters with MUX and Sample/Hold

Check for Samples: ADC12030,ADC12032,ADC12034,ADC12038,ADC12H030,ADC12H032,ADC12H034,ADC12H038

1FEATURES • Single Supply 5V ±10%

• Power consumption 33 mW (max)

2• Serial I/O (MICROWIRE Compatible) – Power down 100 μW (typ)

• 2, 4, or 8 Chan Differential or Single-Ended

Multiplexer DESCRIPTION

• Analog Input Sample/Hold Function NOTE: Some of these devices may be obsolete

• Power Down Mode and are described and shown here for reference

• Variable Resolution and Conversion Rate only. See our web site for product availability.

• Programmable Acquisition Time The ADC12030, and ADC12H030 families are 12-bit

• Variable Digital Output Word Length and plus sign successive approximation Analog-to-Digital

Format Converters with serial I/O and configurable input

multiplexers. The ADC12034/ADC12H034 and

• No Zero or Full Scale Adjustment Required ADC12038/ADC12H038 have 4 and 8 channel

• Fully Tested and Ensured with a 4.096V multiplexers, respectively. The differential multiplexer

Reference outputs and ADC inputs are available on the

• 0V to 5V Analog Input Range with Single 5V MUXOUT1, MUXOUT2, A/DIN1 and A/DIN2 pins.

The ADC12030/ADC12H030 has a two channel

Power Supply multiplexer with the multiplexer outputs and ADC

• No Missing Codes over Temperature inputs internally connected. The ADC12030 family is

tested with a 5 MHz clock, while the ADC12H030

APPLICATIONS family is tested with an 8 MHz clock. On request,

these ADCs go through a self calibration process that

• Medical Instruments adjusts linearity, zero and full-scale errors to less

• Process Control Systems than ±1 LSB each.

• Test Equipment The analog inputs can be configured to operate in

various combinations of single-ended, differential, or

KEY SPECIFICATIONS pseudo-differential modes. A fully differential unipolar

• Resolution 12-bit plus sign analog input range (0V to +5V) can be

accommodated with a single +5V supply. In the

• 12-bit plus sign conversion time differential modes, valid outputs are obtained even

– ADC12H30 family 5.5 μs (max) when the negative inputs are greater than the positive

– ADC12030 family 8.8 μs (max) because of the 12-bit plus sign output data format.

• 12-bit plus sign throughput time The serial I/O is configured to comply with NSC

– ADC12H30 family 8.6 μs (max) MICROWIRE. For voltage references see the

LM4040, LM4050 or LM4041.

– ADC12030 family 14 μs (max)

• Integral Linearity Error ±1 LSB (max)

1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2All trademarks are the property of their respective owners.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

SNAS080K –JULY 1999–REVISED MARCH 2013

www.ti.com

ADC12038 Simplified Block Diagram

Connection Diagram

Top View Top View

Figure 1. 16-Pin Wide Body Figure 2. 20-Pin Wide Body

SOIC Package SOIC Package

See Package Number DW0016B See Package Number DW0020B

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

www.ti.com

SNAS080K –JULY 1999–REVISED MARCH 2013

Top View Top View

Figure 3. 24-Pin Wide Body Figure 4. 28-Pin Wide Body

SOIC, PDIP, SSOP Packages SOIC Package

See Package Numbers DW0024B, NAM0024D, See Package Number DW0028B

DB0024A

PIN DESCRIPTIONS

Pin Name Pin Description

Analog Inputs to the MUX (multiplexer). A channel input is selected by the address information at the DI pin, which

is loaded on the rising edge of SCLK into the address register (See Table 2,Table 3, and Table 4). The voltage

CH0 thru CH7 applied to these inputs should not exceed VA+ or go below VA- or below GND. Exceeding this range on an

unselected channel may corrupt the reading of a selected channel.

COM Analog input pin that is used as a pseudo ground when the analog multiplexer is single-ended.

MUXOUT1 Multiplexer Output pins. If the multiplexer is used, these pins should be connected to the A/DIN pins, directly or

MUXOUT2 through an amplifier and/of filter.

Converter Input pins. MUXOUT1 is usually tied to A/DIN1. MUXOUT2 is usually tied to A/DIN2. If external circuitry

A/DIN1 is placed between MUXOUT1 and A/DIN1, or MUXOUT2 and A/DIN2, it may be necessary to protect these pins

A/DIN2 against voltage overload.. The voltage at these pins should not exceed VA+or go below AGND (see Figure 60).

Data Output pin. This pin is an active push/pull output when CS is low. When CS is high, this output is TRI-STATE.

The conversion result (D0–D12) and converter status data are clocked out by the falling edge of SCLK on this pin.

DO The word length and format of this result can vary (see Table 1). The word length and format are controlled by the

data shifted into the multiplexer address and mode select register (see Table 5).

Serial Data input pin. The data applied to this pin is shifted by the rising edge of SCLK into the multiplexer address

DI and mode select register. Table 2 through Table 5 show the assignment of the multiplexer address and the mode

select data.

This pin is an active push/pull output which indicates the status of the ADC12030/2/4/8. A logic low on this pin

EOC indicates that the ADC is busy with a conversion, Auto Calibration, Auto Zero or power down cycle. The rising edge

of EOC signals the end of one of these cycles.

A logic low is required at this pin to program any mode or to change the ADC's configuration as listed in Mode

Programming Table 5. When this pin is high, the ADC is placed in the read data only mode. While in the read data

only mode, bringing CS low and pulsing SCLK will only clock out the data stored in the ADCs output shift register.

CONV The data on DI will be neglected. A new conversion will not be started and the ADC will remain in the mode and/or

configuration previously programmed. Read data only cannot be performed while a conversion, Auto Cal or Auto

Zero are in progress.

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

SNAS080K –JULY 1999–REVISED MARCH 2013

www.ti.com

PIN DESCRIPTIONS (continued)

Pin Name Pin Description

Chip Select input pin. When a logic low is applied to this pin, the rising edge of SCLK shifts the data on DI into the

address register. This low also brings DO out of TRI-STATE. With CS low the falling edge of SCLK shifts the data

resulting from the previous ADC conversion out at the DO output, with the exception of the first bit of data. When

CS is low continuously, the first bit of the data is clocked out on the rising edge of EOC (end of conversion). When

CS is toggled the falling edge of CS always clocks out the first bit of data. CS should be brought low while SCLK is

low. The falling edge of CS interrupts a conversion in progress and starts the sequence for a new conversion.

CS When CS is brought back low during a conversion, that conversion is prematurely terminated. The data in the

output latches may be corrupted. Therefore, when CS is brought low during a conversion in progress, the data

output at that time should be ignored. CS may also be left continuously low. In this case it is imperative that the

correct number of SCLK pulses be applied to the ADC in order to remain synchronous. After the ADC supply power

is applied the device expects to see 13 clock pulses for each I/O sequence. The number of clock pulses the ADC

expects is the same as the digital output word length. This word length can be modified by the data shifted in on the

DO pin. Table 5 details the data required.

Data Output Ready pin. This pin is an active push/pull output which is low when the conversion result is being

DOR shifted out and goes high to signal that all the data has been shifted out.

Serial Data Clock input. The clock applied to this input controls the rate at which the serial data exchange occurs.

The rising edge loads the information on the DI pin into the multiplexer address and mode select shift register. This

address controls which channel of the analog input multiplexer (MUX) is selected and the mode of operation for the

ADC. With CS low the falling edge of SCLK shifts the data resulting from the previous ADC conversion out on DO,

SCLK with the exception of the first bit of data. When CS is low continuously, the first bit of the data is clocked out on the

rising edge of EOC (end of conversion). When CS is toggled the falling edge of CS always clocks out the first bit of

data. CS should be brought low when SCLK is low. The rise and fall times of the clock edges should not exceed

1 µs.

Conversion Clock input. The clock applied to this input controls the successive approximation conversion time

CCLK interval and the acquisition time. The rise and fall times of the clock edges should not exceed 1 µs.

Positive analog voltage reference input. In order to maintain accuracy, the voltage range of VREF (VREF = VREF+−

VREF+ VREF−) is 1 VDC to 5.0 VDC and the voltage at VREF+ cannot exceed VA+. See Figure 59 for recommended

bypassing.

The negative analog voltage reference input. In order to maintain accuracy, the voltage at this pin must not go

VREF-below GND or exceed VA+. (See Figure 59).

Power Down pin. When PD is high the ADC is powered down; when PD is low the ADC is powered up, or active.

PD The ADC takes a maximum of 250 µs to power up after the command is given.

These are the analog and digital power supply pins. VA+and VD+are not connected together on the chip. These

VA+pins should be tied to the same supply voltage and bypassed separately (see Figure 59). The operating voltage

VD+range of VA+ and VD+ is 4.5 VDC to 5.5 VDC.

DGND The digital ground pin (see Figure 59).

AGND The analog ground pin (see Figure 59).

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

www.ti.com

SNAS080K –JULY 1999–REVISED MARCH 2013

Absolute Maximum Ratings (1)(2)(3)

Positive Supply Voltage (V+= VA+=VD+) 6.5V

except CH0–CH7 and

Voltage at Inputs and Outputs −0.3V to (V++0.3V)

COM

Voltage at Analog Inputs CH0–CH7 and COM GND −5V to (V++5V)

|VA+−VD+| 300 mV

Input Current at Any Pin (4) ±30 mA

Package Input Current (4) ±120 mA

Package Dissipation at

TA= 25°C (5) 500 mW

ESD Susceptibility (6)

Human Body Model 1500V

Soldering Information

PDIP Package (10 seconds) 260°C

SOIC Package (7)

Vapor Phase (60 seconds) 215°C

Infrared (15 seconds) 220°C

Storage Temperature −65°C to +150°C

(1) All voltages are measured with respect to GND, unless otherwise specified.

(2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for

which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the

Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may

degrade when the device is not operated under the listed test conditions.

(3) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and

specifications.

(4) When the input voltage (VIN) at any pin exceeds the power supplies (VIN < GND or VIN > VA+ or VD+), the current at that pin should be

limited to 30 mA. The 120 mA maximum package input current rating limits the number of pins that can safely exceed the power

supplies with an input current of 30 mA to four.

(5) The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax, θJA and the ambient temperature,

TA. The maximum allowable power dissipation at any temperature is PD= (TJmax −TA)/θJA or the number given in the Absolute

Maximum Ratings, whichever is lower.

(6) The human body model is a 100 pF capacitor discharged through a 1.5 kΩresistor into each pin.

(7) See AN450 “Surface Mounting Methods and Their Effect on Product Reliability” or the section titled “Surface Mount” found in any post

1986 Linear Data Book for other methods of soldering surface mount devices.

Operating Ratings (1)(2)

Operating Temperature Range TMIN ≤TA≤TMAX

−40°C ≤TA≤+85°C

Supply Voltage (V+= VA+=VD+) +4.5V to +5.5V

|VA+−VD+| ≤100 mV

VREF+ 0V to VA+

VREF−0V to (VREF+−1V)

VREF (VREF+−VREF−) 1V to VA+

VREF Common Mode Voltage Range

[(VREF+) −(VREF−)] / 2 0.1 VA+ to 0.6 VA+

A/DIN1, A/DIN2, MUXOUT1 and MUXOUT2 Voltage Range 0V to VA+

IN Common Mode Voltage Range

[(VIN+) −(VIN−)] / 2 0V to VA+

(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for

which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the

Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may

degrade when the device is not operated under the listed test conditions.

(2) All voltages are measured with respect to GND, unless otherwise specified.

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

SNAS080K –JULY 1999–REVISED MARCH 2013

www.ti.com

Package Thermal Resistance Part Number Thermal Resistance (θJA)

ADC12(H)030CIWM 70°C/W

ADC12032CIWM 64°C/W

ADC12034CIN 42°C/W

ADC12034CIWM 57°C/W

ADC12H034CIMSA 97°C/W

ADC12(H)038CIWM 50°C/W

NOTE: Some of these devices may be obsolete or on Lifetime Buy status. Check our web site for product

availability.

Converter Electrical Characteristics

The following specifications apply for V+= VA+=VD+ = +5.0 VDC, VREF+ = +4.096 VDC, VREF−= 0 VDC, 12-bit + sign

conversion mode, fCK = fSK = 8 MHz for the ADC12H030, ADC12H032, ADC12H034 and ADC12H038, fCK = fSK = 5 MHz for

the ADC12030, ADC12032, ADC12034 and ADC12038, RS= 25Ω, source impedance for VREF+ and VREF− ≤ 25Ω, fully-

differential input with fixed 2.048V common-mode voltage, and 10(tCK) acquisition time unless otherwise specified. Boldface

limits apply for TA= TJ= TMIN to TMAX;all other limits TA= TJ= 25°C. (1)(2)(3)

Units

Parameter Test Conditions Typical (4) Limits (5) (Limits)

STATIC CONVERTER CHARACTERISTICS

Resolution with No Missing Codes 12 + sign Bits (min)

ILE Integral Linearity Error After Auto Cal (6)(7) ±1/2 ±1 LSB (max)

DNL Differential Non-Linearity After Auto Cal ±1 LSB (max)

Positive Full-Scale Error After Auto Cal (6)(7) ±1/2 ±3.0 LSB (max)

Negative Full-Scale Error After Auto Cal (6)(7) ±1/2 ±3.0 LSB (max)

After Auto Cal (8)(7)

Offset Error ±1/2 ±2 LSB (max)

VIN(+) = VIN (−) = 2.048V

DC Common Mode Error After Auto Cal (9) ±2 ±3.5 LSB (max)

(1) Two on-chip diodes are tied to each analog input through a series resistor as shown below. Input voltage magnitude up to 5V above VA+

or 5V below GND will not damage this device. However, errors in the conversion can occur (if these diodes are forward biased by more

than 50 mV) if the input voltage magnitude of selected or unselected analog input go above VA+ or below GND by more than 50 mV. As

an example, if VA+ is 4.5 VDC, full-scale input voltage must be ≤4.55 VDC to ensure accurate conversions.

(2) To ensure accuracy, it is required that the VA+ and VD+ be connected together to the same power supply with separate bypass

capacitors at each V+pin.

(3) With the test condition for VREF (VREF+−VREF−) given as +4.096V, the 12-bit LSB is 1.0 mV and the 8-bit LSB is 16.0 mV.

(4) Typical figures are at TJ= TA= 25°C and represent most likely parametric norm.

(5) Tested limits are specified to AOQL (Average Outgoing Quality Level).

(6) Positive integral linearity Error is defined as the deviation of the analog value, expressed in LSBs, from the straight line that passes

through positive full-scale and zero. For Negative Integral Linearity Error, the straight line passes through negative full-scale and zero

(see Figure 6 and Figure 7).

(7) The ADC12030 family's self-calibration technique ensures linearity and offset errors as specified, but noise inherent in the self-

calibration process will result in a maximum repeatability uncertainty of 0.2 LSB.

(8) The human body model is a 100 pF capacitor discharged through a 1.5 kΩresistor into each pin.

(9) The DC common-mode error is measured in the differential multiplexer mode with the assigned positive and negative input channels

shorted together.

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

www.ti.com

SNAS080K –JULY 1999–REVISED MARCH 2013

Converter Electrical Characteristics (continued)

The following specifications apply for V+= VA+=VD+ = +5.0 VDC, VREF+ = +4.096 VDC, VREF−= 0 VDC, 12-bit + sign

conversion mode, fCK = fSK = 8 MHz for the ADC12H030, ADC12H032, ADC12H034 and ADC12H038, fCK = fSK = 5 MHz for

the ADC12030, ADC12032, ADC12034 and ADC12038, RS= 25Ω, source impedance for VREF+ and VREF− ≤ 25Ω, fully-

differential input with fixed 2.048V common-mode voltage, and 10(tCK) acquisition time unless otherwise specified. Boldface

limits apply for TA= TJ= TMIN to TMAX;all other limits TA= TJ= 25°C. (1)(2)(3)

Units

Parameter Test Conditions Typical (4) Limits (5) (Limits)

TUE Total Unadjusted Error After Auto Cal (6)(10)(11) ±1 LSB

Resolution with No Missing Codes 8-bit + sign mode 8 + sign Bits (min)

INL Integral Linearity Error 8-bit + sign mode (6) ±1/2 LSB (max)

DNL Differential Non-Linearity 8-bit + sign mode ±3/4 LSB (max)

Positive Full-Scale Error 8-bit + sign mode (6) ±1/2 LSB (max)

Negative Full-Scale Error 8-bit + sign mode (6) ±1/2 LSB (max)

8-bit + sign mode, after Auto Zero

Offset Error ±1/2 LSB (max)

VIN(+) = VIN(−) = + 2.048V (10)

8-bit + sign mode after Auto Zero

TUE Total Unadjusted Error ±3/4 LSB (max)

(6)(10)(11)

Multiplexer Chan-to-Chan Matching ±0.05 LSB

Power Supply Sensitivity V+= +5V ±10%, VREF = +4.096V

Offset Error ±0.5 ±1 LSB (max)

+ Full-Scale Error ±0.5 ±1.5 LSB (max)

−Full-Scale Error ±0.5 ±1.5 LSB (max)

Integral Linearity Error ±0.5 LSB

Output Data from “12-Bit +10 LSB (max)

(see Table 5)(12)

Conversion of Offset” −10 LSB (min)

Output Data from “12-Bit 4095 LSB (max)

(see Table 5)(12)

Conversion of Full-Scale” 4093 LSB (min)

UNIPOLAR DYNAMIC CONVERTER CHARACTERISTICS

fIN = 1 kHz, VIN = 5 VP-P, VREF+= 5.0V 69.4 dB

S/(N+D) Signal-to-Noise Plus Distortion Ratio fIN = 20 kHz, VIN = 5 VP-P, VREF+= 5.0V 68.3 dB

fIN = 40 kHz, VIN = 5 VP-P, VREF+ = 5.0V 65.7 dB

−3 dB Full Power Bandwidth VIN = 5 VP-P, where S/(N+D) drops 3 dB 31 kHz

DIFFERENTIAL DYNAMIC CONVERTER CHARACTERISTICS

fIN = 1 kHz, VIN = ±5V, VREF+= 5.0V 77.0 dB

S/(N+D) Signal-to-Noise Plus Distortion Ratio fIN = 20 kHz, VIN = ±5V, VREF+= 5.0V 73.9 dB

fIN = 40 kHz, VIN = ±5V, VREF+= 5.0V 67.0 dB

−3 dB Full Power Bandwidth VIN = ±5V, where S/(N+D) drops 3 dB 40 kHz

REFERENCE INPUT, ANALOG INPUTS AND MULTIPLEXER CHARACTERISTICS

CREF Reference Input Capacitance 85 pF

A/DIN1, A/DIN2 Analog Input

CA/D 75 pF

Capacitance

A/DIN1, A/DIN2 Analog Input VIN = +5.0V or VIN = 0V ±0.1 ±1.0 µA (max)

Leakage Current

GND −0.05 V (min)

CH0–CH7 and COM Input Voltage (VA+) + 0.05 V (max)

CH0–CH7 and COM Input

CCH 10 pF

Capacitance

CMUXOUT MUX Output Capacitance 20 pF

(10) Offset error is a measure of the deviation from the mid-scale voltage (a code of zero), expressed in LSB. It is the worst-case value of the

code transitions between 1 to 0 and 0 to +1 (see Figure 8).

(11) Total unadjusted error includes offset, full-scale, linearity and multiplexer errors.

(12) The “12-Bit Conversion of Offset” and “12-Bit Conversion of Full-Scale” modes are intended to test the functionality of the device.

Therefore, the output data from these modes are not an indication of the accuracy of a conversion result.

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

SNAS080K –JULY 1999–REVISED MARCH 2013

www.ti.com

Converter Electrical Characteristics (continued)

The following specifications apply for V+= VA+=VD+ = +5.0 VDC, VREF+ = +4.096 VDC, VREF−= 0 VDC, 12-bit + sign

conversion mode, fCK = fSK = 8 MHz for the ADC12H030, ADC12H032, ADC12H034 and ADC12H038, fCK = fSK = 5 MHz for

the ADC12030, ADC12032, ADC12034 and ADC12038, RS= 25Ω, source impedance for VREF+ and VREF− ≤ 25Ω, fully-

differential input with fixed 2.048V common-mode voltage, and 10(tCK) acquisition time unless otherwise specified. Boldface

limits apply for TA= TJ= TMIN to TMAX;all other limits TA= TJ= 25°C. (1)(2)(3)

Units

Parameter Test Conditions Typical (4) Limits (5) (Limits)

On Channel = 5V and Off Channel = 0V −0.01 −0.3 µA (min)

Off Channel Leakage CH0–CH7

and COM Pins (13) On Channel = 0V and Off Channel = 5V 0.01 0.3 µA (max)

On Channel = 5V and Off Channel = 0V 0.01 0.3 µA (max)

On Channel Leakage CH0–CH7

and COM Pins (13) On Channel = 0V and Off Channel = 5V −0.01 −0.3 µA (min)

MUXOUT1 and MUXOUT2 Leakage VMUXOUT = 5.0V or VMUXOUT = 0V 0.01 0.3 µA (max)

Current

RON MUX On Resistance VIN = 2.5V and VMUXOUT = 2.4V 850 1150 Ω(max)

RON Matching Chan-to-Chan VIN = 2.5V and VMUXOUT = 2.4V 5 %

Chan-to-Chan Crosstalk VIN = 5 VP-P, fIN = 40 kHz −72 dB

MUX Bandwidth 90 kHz

(13) Channel leakage current is measured after the channel selection.

DC and Logic Electrical Characteristics

The following specifications apply for V+= VA+=VD+ = +5.0 VDC, VREF+ = +4.096 VDC, VREF−= 0 VDC, 12-bit + sign

conversion mode, fCK = fSK = 8 MHz for the ADC12H030, ADC12H032, ADC12H034 and ADC12H038, fCK = fSK = 5 MHz for

the ADC12030, ADC12032, ADC12034 and ADC12038, RS= 25Ω, source impedance for VREF+ and VREF− ≤ 25Ω, fully-

differential input with fixed 2.048V common-mode voltage, and 10(tCK) acquisition time unless otherwise specified. Boldface

limits apply for TA= TJ= TMIN to TMAX;all other limits TA= TJ= 25°C. (1)(2)(3)

Units

Parameter Test Conditions Typical (4) Limits (5) (Limits)

CCLK, CS, CONV, DI, PD AND SCLK INPUT CHARACTERISTICS

VIN(1) Logical “1” Input Voltage V+= 5.5V 2.0 V (min)

VIN(0) Logical “0” Input Voltage V+= 4.5V 0.8 V (max)

IIN(1) Logical “1” Input Current VIN = 5.0V 0.005 1.0 µA (max)

IIN(0) Logical “0” Input Current VIN = 0V −0.005 −1.0 µA (min)

DO, EOC AND DOR DIGITAL OUTPUT CHARACTERISTICS

V+= 4.5V, IOUT =−360 µA 2.4 V (min)

VOUT(1) Logical “1” Output Voltage V+= 4.5V, IOUT =−10 µA 4.25 V (min)

(1) Two on-chip diodes are tied to each analog input through a series resistor as shown below. Input voltage magnitude up to 5V above VA+

or 5V below GND will not damage this device. However, errors in the conversion can occur (if these diodes are forward biased by more

than 50 mV) if the input voltage magnitude of selected or unselected analog input go above VA+ or below GND by more than 50 mV. As

an example, if VA+ is 4.5 VDC, full-scale input voltage must be ≤4.55 VDC to ensure accurate conversions.

(2) To ensure accuracy, it is required that the VA+ and VD+ be connected together to the same power supply with separate bypass

capacitors at each V+pin.

(3) With the test condition for VREF (VREF+−VREF−) given as +4.096V, the 12-bit LSB is 1.0 mV and the 8-bit LSB is 16.0 mV.

(4) Typical figures are at TJ= TA= 25°C and represent most likely parametric norm.

(5) Tested limits are specified to AOQL (Average Outgoing Quality Level).

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

www.ti.com

SNAS080K –JULY 1999–REVISED MARCH 2013

DC and Logic Electrical Characteristics (continued)

The following specifications apply for V+= VA+=VD+ = +5.0 VDC, VREF+ = +4.096 VDC, VREF−= 0 VDC, 12-bit + sign

conversion mode, fCK = fSK = 8 MHz for the ADC12H030, ADC12H032, ADC12H034 and ADC12H038, fCK = fSK = 5 MHz for

the ADC12030, ADC12032, ADC12034 and ADC12038, RS= 25Ω, source impedance for VREF+ and VREF− ≤ 25Ω, fully-

differential input with fixed 2.048V common-mode voltage, and 10(tCK) acquisition time unless otherwise specified. Boldface

limits apply for TA= TJ= TMIN to TMAX;all other limits TA= TJ= 25°C. (1)(2)(3)

Units

Parameter Test Conditions Typical (4) Limits (5) (Limits)

VOUT(0) Logical “0” Output Voltage V+= 4.5V, IOUT = 1.6 mA 0.4 V (max)

VOUT = 0V −0.1 −3.0 µA (max)

IOUT TRI-STATE Output Current VOUT = 5V 0.1 3.0 µA (max)

+ISC Output Short Circuit Source Current VOUT = 0V 14 6.5 mA (min)

−ISC Output Short Circuit Sink Current VOUT = VD+ 16 8.0 mA (min)

POWER SUPPLY CHARACTERISTICS

Digital Supply Current Awake 1.6 2.5 mA (max)

ADC12030, ADC12032, ADC12034 and CS = HIGH, Powered Down, CCLK on 600 µA

ADC12038 CS = HIGH, Powered Down, CCLK off 20 µA

ID+Digital Supply Current Awake 2.3 3.2 mA

ADC12H030, ADC12H032, ADC12H034 CS = HIGH, Powered Down, CCLK on 0.9 mA

and ADC12H038 CS = HIGH, Powered Down, CCLK off 20 µA

Awake 2.7 4.0 mA (max)

IA+ Positive Analog Supply Current CS = HIGH, Powered Down, CCLK on 10 µA

CS = HIGH, Powered Down, CCLK off 0.1 µA

Awake 70 µA

IREF Reference Input Current CS = HIGH, Powered Down 0.1 µA

AC Electrical Characteristics

The following specifications apply for V+= VA+=VD+ = +5.0 VDC, VREF+ = +4.096 VDC, VREF−= 0 VDC, 12-bit + sign

conversion mode, tr= tf= 3 ns, fCK = fSK = 8 MHz for the ADC12H030, ADC12H032, ADC12H034 and ADC12H038, fCK = fSK

= 5 MHz for the ADC12030, ADC12032, ADC12034 and ADC12038, RS= 25Ω, source impedance for VREF+ and VREF− ≤

25Ω, fully-differential input with fixed 2.048V common-mode voltage, and 10(tCK) acquisition time unless otherwise specified.

Boldface limits apply for TA= TJ= TMIN to TMAX;all other limits TA= TJ= 25°C. (1)

Typical ADC12H030/2/4/8 ADC12030/2/4/8 Units

Parameter Test Conditions (2) Limits (3) Limits (3) (Limits)

fCK Conversion Clock (CCLK) 10 8 5 MHz (max)

Frequency 1 MHz (min)

Serial Data Clock SCLK Frequency 10 8 5 MHz (max)

fSK 0 Hz (min)

40 40 % (min)

Conversion Clock Duty Cycle 60 60 % (max)

40 40 % (min)

Serial Data Clock Duty Cycle 60 60 % (max)

12-Bit + Sign or 12- 44(tCK) 44(tCK)(max)

44(tCK)

Bit 5.5 8.8 µs (max)

tCConversion Time 21(tCK) 21(tCK)(max)

8-Bit + Sign or 8-Bit 21(tCK)2.625 4.2 µs (max)

(1) Timing specifications are tested at the TTL logic levels, VIL = 0.4V for a falling edge and VIH = 2.4V for a rising edge. TRI-STATE output

voltage is forced to 1.4V.

(2) Typical figures are at TJ= TA= 25°C and represent most likely parametric norm.

(3) Tested limits are specified to AOQL (Average Outgoing Quality Level).

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

SNAS080K –JULY 1999–REVISED MARCH 2013

www.ti.com

AC Electrical Characteristics (continued)

The following specifications apply for V+= VA+=VD+ = +5.0 VDC, VREF+ = +4.096 VDC, VREF−= 0 VDC, 12-bit + sign

conversion mode, tr= tf= 3 ns, fCK = fSK = 8 MHz for the ADC12H030, ADC12H032, ADC12H034 and ADC12H038, fCK = fSK

= 5 MHz for the ADC12030, ADC12032, ADC12034 and ADC12038, RS= 25Ω, source impedance for VREF+ and VREF− ≤

25Ω, fully-differential input with fixed 2.048V common-mode voltage, and 10(tCK) acquisition time unless otherwise specified.

Boldface limits apply for TA= TJ= TMIN to TMAX;all other limits TA= TJ= 25°C. (1)

Typical ADC12H030/2/4/8 ADC12030/2/4/8 Units

Parameter Test Conditions (2) Limits (3) Limits (3) (Limits)

6(tCK) 6(tCK)(min)

6(tCK)7(tCK) 7(tCK)(max)

6 Cycles

Programmed 0.75 1.2 µs (min)

0.875 1.4 µs (max)

10(tCK) 10(tCK)(min)

10(tCK)11(tCK) 11(tCK)(max)

10 Cycles

Programmed 1.25 2.0 µs (min)

1.375 2.2 µs (max)

tAAcquisition Time (4) 18(tCK) 18(tCK)(min)

18(tCK)19(tCK) 19(tCK)(max)

18 Cycles

Programmed 2.25 3.6 µs (min)

2.375 3.8 µs (max)

34(tCK) 34(tCK)(min)

34(tCK)35(tCK) 35(tCK)(max)

34 Cycles

Programmed 4.25 6.8 µs (min)

4.375 7.0 µs (max)

4944(tCK)4944(tCK) 4944(tCK)(max)

tCKAL Self-Calibration Time 618.0 988.8 µs (max)

76(tCK)76(tCK) 76(tCK)(max)

tAZ Auto Zero Time 9.5 15.2 µs (max)

2(tCK)2(tCK) 2(tCK)(min)

3(tCK) 3(tCK)(max)

Self-Calibration or Auto Zero

tSYNC Synchronization Time from DOR 0.250 0.40 µs (min)

0.375 0.60 µs (max)

DOR High Time when CS is Low

tDOR Continuously for Read Data and 9(tSK)9(tSK) 9(tSK)(max)

Software Power Up/Down 1.125 1.8 µs (max)

8(tSK)8(tSK) 8(tSK)(max)

tCONV CONV Valid Data Time 1.0 1.6 µs (max)

(4) If SCLK and CCLK are driven from the same clock source, then tAis 6, 10, 18 or 34 clock periods minimum and maximum.

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

www.ti.com

SNAS080K –JULY 1999–REVISED MARCH 2013

Timing Characteristics

The following specifications apply for V+= VA+=VD+ = +5.0 VDC, VREF+ = +4.096 VDC, VREF−= 0 VDC, 12-bit + sign

conversion mode, tr= tf= 3 ns, fCK = fSK = 8 MHz for the ADC12H030, ADC12H032, ADC12H034 and ADC12H03, fCK = fSK =

5 MHz for the ADC12030, ADC12032, ADC12034 and ADC12038, RS= 25Ω, source impedance for VREF+ and VREF− ≤ 25Ω,

fully-differential input with fixed 2.048V common-mode voltage, and 10(tCK) acquisition time unless otherwise specified.

Boldface limits apply for TA= TJ= TMIN to TMAX;all other limits TA= TJ= 25°C. (1)

Typical Limits Units

Parameter Test Conditions (2) (3) (Limits)

Hardware Power-Up Time, Time from PD Falling Edge to

tHPU 140 250 µs (max)

EOC Rising Edge

Software Power-Up Time, Time from Serial Data Clock

tSPU 140 250 µs (max)

Falling Edge to EOC Rising Edge

tACC Access Time Delay from CS Falling Edge to DO Data Valid 20 50 ns (max)

Set-Up Time of CS Falling Edge to Serial Data Clock Rising

tSET-UP 30 ns (min)

Edge

tDELAY Delay from SCLK Falling Edge to CS Falling Edge 0 5ns (min)

t1H, t0H Delay from CS Rising Edge to DO TRI-STATE RL= 3k, CL= 100 pF 40 100 ns (max)

tHDI DI Hold Time from Serial Data Clock Rising Edge 5 15 ns (min)

tSDI DI Set-Up Time from Serial Data Clock Rising Edge 5 10 ns (min)

50 ns (max)

tHDO DO Hold Time from Serial Data Clock Falling Edge RL= 3k, CL= 100 pF 25 5ns (min)

tDDO Delay from Serial Data Clock Falling Edge to DO Data Valid 35 50 ns (max)

DO Rise Time, TRI-STATE to High RL= 3k, CL= 100 pF 10 30 ns (max)

tRDO DO Rise Time, Low to High RL= 3k, CL= 100 pF 10 30 ns (max)

DO Fall Time, TRI-STATE to Low RL= 3k, CL= 100 pF 12 30 ns (max)

tFDO DO Fall Time, High to Low RL= 3k, CL= 100 pF 12 30 ns (max)

tCD Delay from CS Falling Edge to DOR Falling Edge 25 45 ns (max)

Delay from Serial Data Clock Falling Edge to DOR Rising

tSD 25 45 ns (max)

Edge

CIN Capacitance of Logic Inputs 10 pF

COUT Capacitance of Logic Outputs 20 pF

(1) Timing specifications are tested at the TTL logic levels, VIL = 0.4V for a falling edge and VIH = 2.4V for a rising edge. TRI-STATE output

voltage is forced to 1.4V.

(2) Typical figures are at TJ= TA= 25°C and represent most likely parametric norm.

(3) Tested limits are specified to AOQL (Average Outgoing Quality Level).

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

SNAS080K –JULY 1999–REVISED MARCH 2013

www.ti.com

Figure 5. Transfer Characteristic

Figure 6. Simplified Error Curve vs. Output Code without Auto Calibration or Auto Zero Cycles

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

www.ti.com

SNAS080K –JULY 1999–REVISED MARCH 2013

Figure 7. Simplified Error Curve vs. Output Code after Auto Calibration Cycle

Figure 8. Offset or Zero Error Voltage

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

SNAS080K –JULY 1999–REVISED MARCH 2013

www.ti.com

Typical Performance Characteristics (1)

The following curves apply for 12-bit + sign mode after Auto Calibration unless otherwise specified. The performance for 8-bit

+ sign mode is equal to or better than shown.

Linearity Error Change Linearity Error Change

vs. Clock Frequency vs. Temperature

Figure 9. Figure 10.

Linearity Error Change Linearity Error Change

vs. Reference Voltage vs. Supply Voltage

Figure 11. Figure 12.

Full-Scale Error Change Full-Scale Error Change

vs. Clock Frequency vs. Temperature

Figure 13. Figure 14.

(1) With the test condition for VREF (VREF+−VREF−) given as +4.096V, the 12-bit LSB is 1.0 mV and the 8-bit LSB is 16.0 mV.

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

www.ti.com

SNAS080K –JULY 1999–REVISED MARCH 2013

Typical Performance Characteristics (1) (continued)

The following curves apply for 12-bit + sign mode after Auto Calibration unless otherwise specified. The performance for 8-bit

+ sign mode is equal to or better than shown.

Full-Scale Error Change Full-Scale Error Change

vs. Reference Voltage vs. Supply Voltage

Figure 15. Figure 16.

Offset or Zero Error Change Offset or Zero Error Change

vs. Clock Frequency vs. Temperature

Figure 17. Figure 18.

Offset or Zero Error Change Offset or Zero Error Change

vs. Reference Voltage vs. Supply Voltage

Figure 19. Figure 20.

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

SNAS080K –JULY 1999–REVISED MARCH 2013

www.ti.com

Typical Performance Characteristics (1) (continued)

The following curves apply for 12-bit + sign mode after Auto Calibration unless otherwise specified. The performance for 8-bit

+ sign mode is equal to or better than shown.

Analog Supply Current Digital Supply Current

vs. Temperature vs. Clock Frequency

Figure 21. Figure 22.

Digital Supply Current

vs. Temperature

Figure 23.

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

www.ti.com

SNAS080K –JULY 1999–REVISED MARCH 2013

Typical Dynamic Performance Characteristics

The following curves apply for 12-bit + sign mode after Auto Calibration unless otherwise specified.

Bipolar Spectral Response Bipolar Spectral Response

with 1 kHz Sine Wave Input with 10 kHz Sine Wave Input

Figure 24. Figure 25.

Bipolar Spectral Response Bipolar Spectral Response

with 20 kHz Sine Wave Input with 30 kHz Sine Wave Input

Figure 26. Figure 27.

Bipolar Spectral Response Bipolar Spectral Response

with 40 kHz Sine Wave Input with 50 kHz Sine Wave Input

Figure 28. Figure 29.

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

SNAS080K –JULY 1999–REVISED MARCH 2013

www.ti.com

Typical Dynamic Performance Characteristics (continued)

The following curves apply for 12-bit + sign mode after Auto Calibration unless otherwise specified.

Bipolar Spurious Free Unipolar Signal-to-Noise Ratio

Dynamic Range vs. Input Frequency

Figure 30. Figure 31.

Unipolar Signal-to-Noise Unipolar Signal-to-Noise

+ Distortion Ratio + Distortion Ratio

vs. Input Frequency vs. Input Signal Level

Figure 32. Figure 33.

Unipolar Spectral Response Unipolar Spectral Response

with 1 kHz Sine Wave Input with 10 kHz Sine Wave Input

Figure 34. Figure 35.

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

www.ti.com

SNAS080K –JULY 1999–REVISED MARCH 2013

Typical Dynamic Performance Characteristics (continued)

The following curves apply for 12-bit + sign mode after Auto Calibration unless otherwise specified.

Unipolar Spectral Response Unipolar Spectral Response

with 20 kHz Sine Wave Input with 30 kHz Sine Wave Input

Figure 36. Figure 37.

Unipolar Spectral Response Unipolar Spectral Response

with 40 kHz Sine Wave Input with 50 kHz Sine Wave Input

Figure 38. Figure 39.

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

SNAS080K –JULY 1999–REVISED MARCH 2013

www.ti.com

Test Circuits

Figure 40. DO “TRI-STATE” (t1H, tOH)

Figure 41. DO except “TRI-STATE”

Figure 42. Leakage Current

Timing Diagrams

Figure 43. DO Falling and Rising Edge

Figure 44. DO “TRI-STATE” Falling and Rising Edge

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

SCLK

tACC

tSD

tHDO tDDO

2.4V2.4V 2.4V

0.4V

tSET-UP

tCD

0 1 2 3 4 n

DOR

EOC

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

www.ti.com

SNAS080K –JULY 1999–REVISED MARCH 2013

Figure 45. DI Data Input Timing

Figure 46. DO Data Output Timing Using CS

Figure 47. DO Data Output Timing with CS Continuously Low

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

SNAS080K –JULY 1999–REVISED MARCH 2013

www.ti.com

Note: DO output data is not valid during this cycle.

Figure 48. ADC12038 Auto Cal or Auto Zero

Figure 49. ADC12038 Read Data without Starting a Conversion Using CS

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

www.ti.com

SNAS080K –JULY 1999–REVISED MARCH 2013

Figure 50. ADC12038 Read Data without Starting a Conversion with CS Continuously Low

Figure 51. ADC12038 Conversion Using CS with 8-Bit Digital Output Format

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

SNAS080K –JULY 1999–REVISED MARCH 2013

www.ti.com

Figure 52. ADC12038 Conversion Using CS with 16-Bit Digital Output Format

Figure 53. ADC12038 Conversion with CS Continuously Low and 8-Bit Digital Output Format

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

www.ti.com

SNAS080K –JULY 1999–REVISED MARCH 2013

Figure 54. ADC12038 Conversion with CS Continuously Low and 16-Bit Digital Output Format

Figure 55. ADC12038 Software Power Up/Down Using CS with 16-Bit Digital Output Format

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

SNAS080K –JULY 1999–REVISED MARCH 2013

www.ti.com

Figure 56. ADC12038 Software Power Up/Down with CS Continuously Low and 16-Bit Digital Output

Format

Note: Hardware power up/down may occur at any time. If PD is high while a conversion is in progress that conversion

will be corrupted and erroneous data will be stored in the output shift register.

Figure 57. ADC12038 Hardware Power Up/Down

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC

VA+**

0.01 uF **

0.1 uF 10 uF *

+5.0V

VD+

VREF+

VREF-

+4.096V

DGNDAGND

ANALOG INPUT VOLTAGE

GROUND REFERENCE

ANALOG

INPUT

VOLTAGE

ASSIGNED

(+) INPUT

ANALOG

INPUT

VOLTAGE ASSIGNED

(-) INPUT

0.01 uF **

0.1 uF 10 uF *

0.01 uF **

0.1 uF 10 uF *

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

www.ti.com

SNAS080K –JULY 1999–REVISED MARCH 2013

Note: In order for all 9 bits of Status Information to be accessible, the last conversion programmed before Cycle N

needs to have a resolution of 8 bits plus sign, 12 bits, 12 bits plus sign, or greater.

Figure 58. ADC12038 Configuration Modification—Example of a Status Read

*Tantalum

**Monolithic Ceramic or better

Figure 59. Recommended Power Supply Bypassing and Grounding

Figure 60. Protecting the MUXOUT1, MUXOUT2, A/DIN1 and A/DIN2 Analog Pins

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

SNAS080K –JULY 1999–REVISED MARCH 2013

www.ti.com

Format and Set-Up Tables

Table 1. Data Out Formats(1)

DO Formats DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 DB8 DB9 DB10 DB11 DB12 DB13 DB14 DB15 DB16

17 X X X X Sign MSB 10 9 8 7 6 5 4 3 2 1 LSB

Bits

MSB 13 Sign MSB 10 9 8 7 6 5 4 3 2 1 LSB

First Bits

9Sign MSB 6 5 4 3 2 1 LSB

Bits

with Sign 17 LSB 1 2 3 4 5 6 7 8 9 10 MSB Sign X X X X

Bits

LSB 13 LSB 1 2 3 4 5 6 7 8 9 10 MSB Sign

First Bits

9LSB 1 2 3 4 5 6 MSB Sign

Bits

16 0 0 0 0 MSB 10 9 8 7 6 5 4 3 2 1 LSB

Bits

MSB 12 MSB 10 9 8 7 6 5 4 3 2 1 LSB

First Bits

8MSB 6 5 4 3 2 1 LSB

Bits

without

sign 16 LSB 1 2 3 4 5 6 7 8 9 10 MSB 0 0 0

Bits

LSB 12 LSB 1 2 3 4 5 6 7 8 9 10 MSB

First Bits

8LSB 1 2 3 4 5 6 MSB

Bits

(1) X = High or Low state.

Table 2. ADC12038 Multiplexer Addressing

Analog Channel Addressed

and Assignment ADC Input Polarity Multiplexer Output

MUX Address with A/DIN1 tied to MUXOUT1 Assignment Channel Assignment Mode

and A/DIN2 tied to MUXOUT2

DI0 DI1 DI2 DI3 CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 COM A/DIN1 A/DIN2 MUXOUT1 MUXOUT2

LLLL + −+−CH0 CH1

L L L H + −+−CH2 CH3

L L H L + −+−CH4 CH5

L L H H + −+−CH6 CH7 Differential

L H L L −+−+ CH0 CH1

L H L H −+−+ CH2 CH3

L H H L −+−+ CH4 CH5

L H H H −+−+ CH6 CH7

H L L L + −+−CH0 COM

H L L H + −+−CH2 COM

H L H L + −+−CH4 COM

H L H H + −+−CH6 COM Single-Ended

H H L L + −+−CH1 COM

H H L H + −+−CH3 COM

H H H L + −+−CH5 COM

HHHH + −+−CH7 COM

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

www.ti.com

SNAS080K –JULY 1999–REVISED MARCH 2013

Table 3. ADC12034 Multiplexer Addressing

Analog Channel Addressed

and Assignment ADC Input Polarity Multiplexer Output Channel

MUX Address with A/DIN1 tied to MUXOUT1 Assignment Assignment Mode

and A/DIN2 tied to MUXOUT2

DI0 DI1 DI2 CH0 CH1 CH2 CH3 COM A/DIN1 A/DIN2 MUXOUT1 MUXOUT2

L L L + −+−CH0 CH1

L L H + −+−CH2 CH3 Differential

L H L −+−+ CH0 CH1

L H H −+−+ CH2 CH3

H L L + −+−CH0 COM

H L H + −+−CH2 COM Single-Ended

H H L + −+−CH1 COM

H H H + −+−CH3 COM

Table 4. ADC12032 and ADC12030 Multiplexer Addressing

Analog Channel Addressed

and Assignment ADC Input Polarity Multiplexer Output

MUX Address Mode

with A/DIN1 tied to MUXOUT1 Assignment Channel Assignment

and A/DIN2 tied to MUXOUT2

DI0 DI1 CH0 CH1 COM A/DIN1 A/DIN2 MUXOUT1 MUXOUT2

L L + −+−CH0 CH1 Differential

L H −+−+ CH0 CH1

H L + −+−CH0 COM Single-Ended

H H + −+−CH1 COM

NOTE

ADC12030 and ADC12H030 do not have A/DIN1, A/DIN2, MUXOUT1 and MUXOUT2

pins.

Table 5. Mode Programming(1)

ADC12038 DI0 DI1 DI2 DI3 DI4 DI5 DI6 DI7

ADC12034 DI0 DI1 DI2 DI3 DI4 DI5 DI6 DO Format

Mode Selected (next Conversion

ADC12030 (Current) Cycle)

and DI0 DI1 DI2 DI3 DI4 DI5

ADC12032

See Table 2,Table 3, or L L L L 12 Bit Conversion 12 or 13 Bit MSB First

Table 4

See Table 2,Table 3, or L L L H 12 Bit Conversion 16 or 17 Bit MSB First

Table 4

See Table 2,Table 3, or L L H L 8 Bit Conversion 8 or 9 Bit MSB First

Table 4

L L L L L L H H 12 Bit Conversion of Full-Scale 12 or 13 Bit MSB First

See Table 2,Table 3, or L H L L 12 Bit Conversion 12 or 13 Bit LSB First

Table 4

See Table 2,Table 3, or L H L H 12 Bit Conversion 16 or 17 Bit LSB First

Table 4

See Table 2,Table 3, or L H H L 8 Bit Conversion 8 or 9 Bit LSB First

Table 4

(1) The ADC powers up with no Auto Cal, no Auto Zero, 10 CCLK acquisition time, 12-bit + sign conversion, power up, 12- or 13-bit MSB

first, and user mode.

X = Don't Care

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

SNAS080K –JULY 1999–REVISED MARCH 2013

www.ti.com

Table 5. Mode Programming(1) (continued)

ADC12038 DI0 DI1 DI2 DI3 DI4 DI5 DI6 DI7

ADC12034 DI0 DI1 DI2 DI3 DI4 DI5 DI6 DO Format

Mode Selected (next Conversion

ADC12030 (Current) Cycle)

and DI0 DI1 DI2 DI3 DI4 DI5

ADC12032

L L L L L H H H 12 Bit Conversion of Offset 12 or 13 Bit LSB First

L L L L H L L L Auto Cal No Change

L L L L H L L H Auto Zero No Change

L L L L H L H L Power Up No Change

L L L L H L H H Power Down No Change

L L L L H H L L Read Status Register No Change

L L L L H H L H Data Out without Sign No Change

H L L L H H L H Data Out with Sign No Change

L L L L H H H L Acquisition Time—6 CCLK Cycles No Change

L H L L H H H L Acquisition Time—10 CCLK Cycles No Change

H L L L H H H L Acquisition Time—18 CCLK Cycles No Change

H H L L H H H L Acquisition Time—34 CCLK Cycles No Change

L L L L H H H H User Mode No Change

Test Mode

H X X X H H H H No Change

(CH1–CH7 become Active Outputs)

Table 6. Conversion/Read Data Only Mode Programming

CS CONV PD Mode

L L L See Table 5 for Mode

L H L Read Only (Previous DO Format). No Conversion.

H X L Idle

X X H Power Down

Table 7. Status Register

Status Bit DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 DB8

Location

Status Bit PU PD Cal 8 or 9 12 or 13 16 or 17 Sign Justification Test Mode

Device Status DO Output Format Status

“High” “High” “High” “High” “High” “High” “High” When “High” When “High”

indicates a indicates a indicates an indicates an indicates a indicates a indicates the the device is

Power Up Power Auto Cal 8 or 9 bit 12 or 13 bit 16 or 17 bit that the conversion in test mode.

Sequence Down Sequence format format format sign bit is result will be When “Low”

is in Sequence is in included. output MSB the device is

Function progress is in progress When “Low” first. When in user

progress the sign bit “Low” the mode.

is not result will be

included. output LSB

first.

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

www.ti.com

SNAS080K –JULY 1999–REVISED MARCH 2013

APPLICATIONS INFORMATION

1.0 DIGITAL INTERFACE

1.1 Interface Concepts

The example in Figure 61 shows a typical sequence of events after the power is applied to the ADC12030/2/4/8:

Figure 61. Typical Power Supply Power Up Sequence

The first instruction input to the ADC via DI initiates Auto Cal. The data output on DO at that time is meaningless

and is completely random. To determine whether the Auto Cal has been completed, a read status instruction

should be issued to the ADC. Again the data output at that time has no significance since the Auto Cal procedure

modifies the data in the output shift register. To retrieve the status information, an additional read status

instruction should be issued to the ADC. At this time the status data is available on DO. If the Cal signal in the

status word is low, Auto Cal has been completed. Therefore, the next instruction issued can start a conversion.

The data output at this time is again status information.

To keep noise from corrupting the conversion, status can not be read during a conversion. If CS is strobed and is

brought low during a conversion, that conversion is prematurely ended. EOC can be used to determine the end

of a conversion or the ADC controller can keep track in software of when it would be appropriate to communicate

to the ADC again. Once it has been determined that a conversion has completed, another instruction can be

transmitted to the ADC. The data from this conversion can be accessed when the next instruction is issued to the

ADC.

Note, when CS is low continuously it is important to transmit the exact number of SCLK cycles, as shown in the

timing diagrams. Not doing so will desynchronize the serial communication to the ADC. (See Section 1.3 CS Low

Continuously Considerations.)

1.2 Changing Configuration

The configuration of the ADC12030/2/4/8 on power up defaults to 12-bit plus sign resolution, 12- or 13-bit MSB

First, 10 CCLK acquisition time, user mode, no Auto Cal, no Auto Zero, and power up mode. Changing the

acquisition time and turning the sign bit on and off requires an 8-bit instruction to be issued to the ADC. This

instruction will not start a conversion. The instructions that select a multiplexer address and format the output

data do start a conversion. Figure 62 describes an example of changing the configuration of the

ADC12030/2/4/8.

During I/O sequence 1, the instruction at DI configures the ADC12030/2/4/8 to do a conversion with 12-bit +sign

resolution. Notice that when the 6 CCLK Acquisition and Data Out without Sign instructions are issued to the

ADC, I/O sequences 2 and 3, a new conversion is not started. The data output during these instructions is from

conversion N which was started during I/O sequence 1. Figure 58 in detail the sequence of events necessary for

a Data Out without Sign, Data Out with Sign, or 6/10/18/34 CCLK Acquisition time mode selection. Table 5

describes the actual data necessary to be input to the ADC to accomplish this configuration modification. The

next instruction issued to the ADC, shown in Figure 62, starts conversion N+1 with 8 bits of resolution formatted

MSB first. Again the data output during this I/O cycle is the data from conversion N.

The number of SCLKs applied to the ADC during any conversion I/O sequence should vary in accord with the

data out word format chosen during the previous conversion I/O sequence. The various formats and resolutions

available are shown in Table 1.InFigure 62, since 8-bit without sign, MSB first format was chosen during I/O

sequence 4, the number of SCLKs required during I/O sequence 5 is eight. In the following I/O sequence the

format changes to 12-bit without sign MSB first; therefore the number of SCLKs required during I/O sequence 6

changes accordingly to 12.

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

SNAS080K –JULY 1999–REVISED MARCH 2013

www.ti.com

1.3 CS Low Continuously Considerations

When CS is continuously low, it is important to transmit the exact number of SCLK pulses that the ADC expects.

Not doing so will desynchronize the serial communications to the ADC. When the supply power is first applied to

the ADC, it will expect to see 13 SCLK pulses for each I/O transmission. The number of SCLK pulses that the

ADC expects to see is the same as the digital output word length. The digital output word length is controlled by

the Data Out (DO) format. The DO format maybe changed any time a conversion is started or when the sign bit

is turned on or off. The table below details out the number of clock periods required for different DO formats:

DO Format Number of SCLKs Expected

SIGN OFF 8

8-Bit MSB or LSB First SIGN ON 9

SIGN OFF 12

12-Bit MSB or LSB First SIGN ON 13

SIGN OFF 16

16-Bit MSB or LSB first SIGN ON 17

If erroneous SCLK pulses desynchronize communications, the simplest way to recover is by cycling the power

supply to the device. Not being able to easily resynchronize the device is a shortcoming of leaving CS low

continuously.

The number of clock pulses required for an I/O exchange may be different for the case when CS is left low

continuously vs. the case when CS is cycled. Take the I/O sequence detailed in Figure 61 (Typical Power Supply

Sequence) as an example. The table below lists the number of SCLK pulses required for each instruction:

Instruction CS Low Continuously CS Strobed

Auto Cal 13 SCLKs 8 SCLKs

Read Status 13 SCLKs 8 SCLKs

12-Bit + Sign Conv 1 13 SCLKs 8 SCLKs

12-Bit + Sign Conv 2 13 SCLKs 13 SCLKs

1.4 Analog Input Channel Selection

The data input at DI also selects the channel configuration (see Table 2,Table 3,Table 4, and Table 5). In

Figure 62 the only times when the channel configuration could be modified is during I/O sequences 1, 4, 5 and 6.

Input channels are reselected before the start of each new conversion. Shown below is the data bit stream

required at DI, during I/O sequence number 4 in Figure 62, to set CH1 as the positive input and CH0 as the

negative input for the different versions of ADCs:

Part DI Data(1)

Number DI0 DI1 DI2 DI3 DI4 DI5 DI6 DI7

ADC12H030ADC12030 L H L L H L X X

ADC12H032ADC12032 L H L L H L X X

ADC12H034ADC12034 L H L L L H L X

ADC12H038ADC12038 L H L L L L H L

(1) X can be a logic high (H) or low (L).

1.5 Power Up/Down

The ADC may be powered down by taking the PD pin HIGH or by the instruction input at DI (see Table 5 and

Table 6, and the Power Up/Down timing diagrams). When the ADC is powered down in this way, the ADC

conversion circuitry is deactivated but the digital I/O circuitry is kept active.

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

www.ti.com

SNAS080K –JULY 1999–REVISED MARCH 2013

Hardware power up/down is controlled by the state of the PD pin. Software power-up/down is controlled by the

instruction issued to the ADC. If a software power up instruction is issued to the ADC while a hardware power

down is in effect (PD pin high) the device will remain in the power-down state. If a software power down

instruction is issued to the ADC while a hardware power up is in effect (PD pin low), the device will power down.

When the device is powered down by software, it may be powered up by either issuing a software power up

instruction or by taking PD pin high and then low. If the power down command is issued during a conversion, that

conversion is interrupted, so the data output after power up cannot be relied upon.

Figure 62. Changing the ADC's Conversion Configuration

1.6 User Mode and Test Mode

An instruction may be issued to the ADC to put it into test mode, which is used by the manufacturer to verify

complete functionality of the device. During test mode CH0–CH7 become active outputs. If the device is

inadvertently put into the test mode with CS continuously low, the serial communications may be

desynchronized. Synchronization may be regained by cycling the power supply voltage to the device. Cycling the

power supply voltage will also set the device into user mode. If CS is used in the serial interface, the ADC may

be queried to see what mode it is in. This is done by issuing a “read STATUS register” instruction to the ADC.

When bit 9 of the status register is high, the ADC is in test mode; when bit 9 is low the ADC, is in user mode. As

an alternative to cycling the power supply, an instruction sequence may be used to return the device to user

mode. This instruction sequence must be issued to the ADC using CS. The following table lists the instructions

required to return the device to user mode. Note that this entire sequence, including both Test Mode and User

Mode values, should be sent to recover from the test mode.

DI Data(1)

Instruction DI0 DI1 DI2 DI3 DI4 DI5 DI6 D17

TEST MODE H X X X H H H H

Reset L L L L H H H L

Test Mode L L L L H L H L

Instructions L L L L H L H H

USER MODE L L L L H H H H

Power Up L L L L H L H L

Set DO with or without Sign H or L L L L H H L H

Set Acquisition Time H or L H or L L L H H H L

Start a Conversion H or L H or L H or L H or L L H or L H or L H or L

(1) X = Don't Care

The power up, data with or without sign, and acquisition time instructions should be resent after returning to the

user mode. This is to ensure that the ADC is in the required state before a conversion is started.

1.7 Reading the Data Without Starting a Conversion

The data from a particular conversion may be accessed without starting a new conversion by ensuring that the

CONV line is taken high during the I/O sequence. See Figure 49 and Figure 50.Table 6 describes the operation

of the CONV pin. It is not necessary to read the data as soon as DOR goes low. The data will remain in the

output register ifCS is brought high right after DOR goes high. A single conversion may be read as many times

as desired before CS is brought low.

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

SNAS080K –JULY 1999–REVISED MARCH 2013

www.ti.com

1.8 Brown Out Conditions

When the supply voltage dips below about 2.7V, the internal registers, including the calibration coefficients and

all of the other registers, may lose their contents. When this happens the ADC will not perform as expected or

not at all after power is fully restored. While writing the desired information to all registers and performing a

calibration might sometimes cause recovery to full operation, the only sure recovery method is to reduce the

supply voltage to below 0.5V, then reprogram the ADC and perform a calibration after power is fully restored.

2.0 THE ANALOG MULTIPLEXER

For the ADC12038, the analog input multiplexer can be configured with 4 differential channels or 8 single ended

channels with the COM input as the zero reference or any combination thereof (see Figure 63). The difference

between the voltages at the VREF+and VREF−pins determines the input voltage span (VREF). The analog input

voltage range is 0 to VA+. Negative digital output codes result when VIN−> VIN+. The actual voltage at VIN−or VIN+

cannot go below AGND. 8 Single-Ended Channels

4 Differential with COM

Channels as Zero Reference

Figure 63. Input Multiplexer Options

Differential Single-Ended

Configuration Configuration

A/DIN1 and A/DIN2 can be assigned as the + or −input

A/DIN1 is + input

A/DIN2 is −input

Figure 64. MUXOUT connections for multiplexer option

CH0, CH2, CH4, and CH6 can be assigned to the MUXOUT1 pin in the differential configuration, while CH1,

CH3, CH5, and CH7 can be assigned to the MUXOUT2 pin. In the differential configuration, the analog inputs

are paired as follows: CH0 with CH1, CH2 with CH3, CH4 with CH5 and CH6 with CH7. The A/DIN1 and A/DIN2

pins can be assigned positive or negative polarity.

With the single-ended multiplexer configuration, CH0 through CH7 can be assigned to the MUXOUT1 pin. The

COM pin is always assigned to the MUXOUT2 pin. A/DIN1 is assigned as the positive input; A/DIN2 is assigned

as the negative input. (See Figure 64).

The Multiplexer assignment tables for these ADCs (Table 2,Table 3, andTable 4) summarize the aforementioned

functions for the different versions of ADCs.

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC1203Y

VA+0.01 uF 0.1 uF 10 uF

0.01 uF 0.1 uF 10 uF

0.01 uF 0.1 uF 10 uF LM4040-2.5

430:

+5.0V

VD+

VREF+

VREF-

+2.5V

DGNDAGND

ANALOG INPUT VOLTAGE

GROUND REFERENCE

CH0

CH1

CH2

CH8

COM

ANALOG INPUT

VOLTAGE RANGE

0V to 5V

12-BITS SIGNED ASSIGNED

(+) INPUT

ASSIGNED

(-) INPUT

600:R1

(DEPENDS UPON

ACQUISITION TIME)

ADC1203Y

VA+0.01 uF 0.1 uF 10 uF

0.01 uF 0.1 uF 10 uF

LM4040-4.1

+5.0V

VD+

VREF+

VREF-

+4.096V

DGNDAGND

ANALOG INPUT VOLTAGE

GROUND REFERENCE

CH0

CH2

CH4

CH6

COM

ASSIGNED

(+) INPUT

ASSIGNED

(-) INPUT

ANALOG INPUT

VOLTAGE RANGE

0V TO 4.096V

12-BITS

UNSIGNED

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

www.ti.com

SNAS080K –JULY 1999–REVISED MARCH 2013

2.1 Biasing for Various Multiplexer Configurations

Figure 65 is an example of device connections for single-ended operation. The sign bit is always low. The digital

output range is 0 0000 0000 0000 to 0 1111 1111 1111. One LSB is equal to 1 mV (4.1V/4096 LSBs).

Figure 65. Single-Ended Biasing

For pseudo-differential signed operation, the circuit of Figure 66 shows a signal AC coupled to the ADC. This

gives a digital output range of −4096 to +4095. With a 2.5V reference, 1 LSB is equal to 610 µV. Although the

ADC is not production tested with a 2.5V reference, when VA+and VD+are +5.0V, linearity error typically will not

change more than 0.1 LSB (see the curves in the Typical Electrical Characteristics Section). With the ADC set to

an acquisition time of 10 clock periods, the input biasing resistor needs to be 600Ωor less. Notice though that

the input coupling capacitor needs to be made fairly large to bring down the high pass corner. Increasing the

acquisition time to 34 clock periods (with a 5 MHz CCLK frequency) would allow the 600Ωto increase to 6k,

which with a 1 µF coupling capacitor would set the high pass corner at 26 Hz. Increasing R, to 6k would allow R2

to be 2k.

Figure 66. Pseudo-Differential Biasing with the Signal Source AC Coupled Directly into the ADC

An alternative method for biasing pseudo-differential operation is to use the +2.5V from the LM4040 to bias any

amplifier circuits driving the ADC as shown in Figure 67. The value of the resistor pull-up biasing the LM4040-2.5

will depend upon the current required by the op amp biasing circuitry.

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC1203Y

VA+0.01 uF 0.1 uF 10 uF

0.01 uF 0.1 uF 10 uF

LM4041-ADJ

+5.0V

VD+

VREF+

VREF-

+2.048V

DGNDAGND

ANALOG INPUT VOLTAGE

GROUND REFERENCE

CH0

CH2

CH4

CH6

COM

ASSIGNED

(+) INPUT

ASSIGNED

(-) INPUT

+5.0V

ANALOG

INPUT

VOLTAGE

ANALOG INPUT

VOLTAGE RANGE

2.5V +/- 2.048V

12-BITS SIGNED

LM4040-2.5

1M 1k

ADC1203Y

VA+0.01 uF 0.1 uF 10 uF

0.01 uF 0.1 uF 10 uF

0.01 uF 0.1 uF 10 uF LM4040-2.5

+5.0V

VD+

VREF+

VREF-

+2.5V

DGNDAGND

ANALOG INPUT VOLTAGE

GROUND REFERENCE

CH0

CH2

CH4

CH6

COM

ASSIGNED

(+) INPUT

ASSIGNED

(-) INPUT

ANALOG

INPUT

VOLTAGE

ANALOG INPUT

VOLTAGE

RANGE

0V to 5V

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

SNAS080K –JULY 1999–REVISED MARCH 2013

www.ti.com

In the circuit of Figure 67, some voltage range is lost since the amplifier will not be able to swing to +5V and

GND with a single +5V supply. Using an adjustable version of the LM4041 to set the full scale voltage at exactly

2.048V and a lower grade LM4040D-2.5 to bias up everything to 2.5V as shown in Figure 68 will allow the use of

all the ADC's digital output range of −4096 to +4095 while leaving plenty of head room for the amplifier.

Fully differential operation is shown in Figure 69. One LSB for this case is equal to (4.1V/4096) = 1 mV.

Figure 67. Alternative Pseudo-Differential Biasing

Figure 68. Pseudo-Differential Biasing without the Loss of Digital Output Range

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC1203Y

VA+0.01 uF 0.1 uF 10 uF

0.01 uF 0.1 uF 10 uF

LM4040-4.1

+5.0V

VD+

VREF+

VREF-

+4.1V

DGNDAGND

ANALOG INPUT VOLTAGE

GROUND REFERENCE

CH0

CH2

CH4

CH6

CH1

CH3

CH5

CH7

ANALOG INPUT

VOLTAGE RANGE

0.45V to 4.55V ASSIGNED

(+) INPUT

ANALOG INPUT

VOLTAGE RANGE

0.45V to 4.55V ASSIGNED

(-) INPUT

FULLY DIFFERENTIAL

12-BIT PLUS SIGN

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

www.ti.com

SNAS080K –JULY 1999–REVISED MARCH 2013

Figure 69. Fully Differential Biasing

3.0 REFERENCE VOLTAGE

The difference in the voltages applied to the VREF+and VREF−defines the analog input span (the difference

between the voltage applied between two multiplexer inputs or the voltage applied to one of the multiplexer

inputs and analog ground) over which 4095 positive and 4096 negative codes exist. The voltage sources driving

VREF+and VREF−must have very low output impedance and noise. The circuit in Figure 70 is an example of a

very stable reference appropriate for use with the device.

*Tantalum

Figure 70. Low Drift Extremely

Stable Reference Circuit

The ADC12030/2/4/8 can be used in either ratiometric or absolute reference applications. In ratiometric systems,

the analog input voltage is proportional to the voltage used for the ADC's reference voltage. When this voltage is

the system power supply, the VREF+pin is connected to VA+and VREF−is connected to ground. This technique

relaxes the system reference stability requirements because the analog input voltage and the ADC reference

voltage move together. This maintains the same output code for given input conditions. For absolute accuracy,

where the analog input voltage varies between very specific voltage limits, a time and temperature stable voltage

source can be connected to the reference inputs. Typically, the reference voltage magnitude will require an initial

adjustment to null reference voltage induced full-scale errors.

Below are recommended references along with some key specifications.

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

SNAS080K –JULY 1999–REVISED MARCH 2013

www.ti.com

Part Number Output Voltage Tolerance Temperature Coefficient

LM4041CI-Adj ±0.5% ±100ppm/°C

LM4040AI-4.1 ±0.1% ±100ppm/°C

LM4120AI-4.1 ±0.2% ±50ppm/°C

LM4121AI-4.1 ±0.2% ±50ppm/°C

LM4050AI-4.1 ±0.1% ±50ppm/°C

LM4030AI-4.1 ±0.05% ±10ppm/°C

LM4140AC-4.1 ±0.1% ±3.0ppm/°C

Circuit of Figure 70 Adjustable ±2ppm/°C

The reference voltage inputs are not fully differential. The ADC12030/2/4/8 will not generate correct conversions

or comparisons if VREF+is taken below VREF−. Correct conversions result when VREF+and VREF−differ by 1V or

more and remain at all times between ground and VA+. The VREF common mode range, (VREF++ VREF−)/2, is

restricted to (0.1 × VA+) to (0.6 × VA+). Therefore, with VA+= 5V the center of the reference ladder should not go

below 0.5V or above 3.0V. Figure 71 is a graphic representation of the voltage restrictions on VREF+and VREF−.

Figure 71. VREF Operating Range

4.0 ANALOG INPUT VOLTAGE RANGE

The ADC12030/2/4/8's fully differential ADC generate a two's complement output that is found by using the

equations shown below:

for (12-bit) resolution the Output Code =

(1)

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

www.ti.com

SNAS080K –JULY 1999–REVISED MARCH 2013

for (8-bit) resolution the Output Code =

(2)

Round off to the nearest integer value between −4096 to 4095 for 12-bit resolution and between −256 to 255 for

8-bit resolution if the result of the above equation is not a whole number.

Examples are shown in the table below:

VREF+VREF−VIN+VIN−Digital Output Code

+2.5V +1V +1.5V 0V 0,1111,1111,1111

+4.096V 0V +3V 0V 0,1011,1011,1000

+4.096V 0V +2.499V +2.500V 1,1111,1111,1111

+4.096V 0V 0V +4.096V 1,0000,0000,0000

5.0 INPUT CURRENT

At the start of the acquisition window (tA) a charging current flows into or out of the analog input pins (A/DIN1 and

A/DIN2) depending upon the input voltage polarity. The analog input pins are CH0–CH7 and COM when A/DIN1

is tied to MUXOUT1 and A/DIN2 is tied to MUXOUT2. The peak value of this input current will depend upon the

actual input voltage applied, the source impedance and the internal multiplexer switch on resistance. With

MUXOUT1 tied to A/DIN1 and MUXOUT2 tied to A/DIN2 the internal multiplexer switch on resistance is typically

1.6 kΩ. The A/DIN1 and A/DIN2 mux on resistance is typically 750Ω.

6.0 INPUT SOURCE RESISTANCE

For low impedance voltage sources (<600Ω), the input charging current will decay before the end of the S/H's

acquisition time of 2 µs (10 CCLK periods with fC= 5 MHz), to a value that will not introduce any conversion

errors. For high source impedances, the S/H's acquisition time can be increased to 18 or 34 CCLK periods. For

less ADC resolution and/or slower CCLK frequencies the S/H's acquisition time may be decreased to 6 CCLK

periods. To determine the number of clock periods (Nc) required for the acquisition time with a specific source

impedance for the various resolutions the following equations can be used:

12 Bit + Sign NC= [RS+ 2.3] × fC× 0.824

8 Bit + Sign NC= [RS+ 2.3] × fC× 0.57

where

• fCis the conversion clock (CCLK) frequency in MHz

• RSis the external source resistance in kΩ(3)

As an example, operating with a resolution of 12 Bits+sign, a 5 MHz clock frequency and maximum acquisition

time of 34 conversion clock periods the ADC's analog inputs can handle a source impedance as high as 6 kΩ.

The acquisition time may also be extended to compensate for the settling or response time of external circuitry

connected between the MUXOUT and A/DIN pins.

An acquisition starts at a falling edge of SCLK and ends at a rising edge of CCLK (see timing diagrams). If SCLK

and CCLK are asynchronous, one extra CCLK clock period may be inserted into the programmed acquisition

time for synchronization. Therefore, with asynchronous SCLK and CCLKs the acquisition time will change from

conversion to conversion.

7.0 INPUT BYPASS CAPACITANCE

External capacitors (0.01 µF–0.1 µF) can be connected between the analog input pins, CH0–CH7, and analog

ground to filter any noise caused by inductive pickup associated with long input leads. These capacitors will not

degrade the conversion accuracy.

8.0 NOISE

The leads to each of the analog multiplexer input pins should be kept as short as possible. This will minimize

input noise and clock frequency coupling that can cause conversion errors. Input filtering can be used to reduce

the effects of the noise sources.

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

SNAS080K –JULY 1999–REVISED MARCH 2013

www.ti.com

9.0 POWER SUPPLIES

Noise spikes on the VA+and VD+supply lines can cause conversion errors; the comparator will respond to the

noise. The ADC is especially sensitive to any power supply spikes that occur during the Auto Zero or linearity

correction. The minimum power supply bypassing capacitors recommended are low inductance tantalum

capacitors of 10 µF or greater paralleled with 0.1 µF monolithic ceramic capacitors. More or different bypassing

may be necessary depending upon the overall system requirements. Separate bypass capacitors should be used

for the VA+and VD+supplies and placed as close as possible to these pins.

10.0 GROUNDING

The ADC12030/2/4/8's performance can be maximized through proper grounding techniques. These include the

use of separate analog and digital areas of the board with analog and digital components and traces located only

in their respective areas. Bypass capacitors of 0.01 µF and 0.1 µF surface mount capacitors and a 10 µF are

recommended at each of the power supply pins for best performance. These capacitors should be located as

close to the bypassed pin as practical, especially the smaller value capacitors.

11.0 CLOCK SIGNAL LINE ISOLATION

The ADC12030/2/4/8's performance is optimized by routing the analog input/output and reference signal

conductors as far as possible from the conductors that carry the clock signals to the CCLK and SCLK pins.

Maintaining a separation of at least 7 to 10 times the height of the clock trace above its reference plane is

recommended.

12.0 THE CALIBRATION CYCLE

A calibration cycle needs to be started after the power supplies, reference, and clock have been given enough

time to stabilize after initial turn-on. During the calibration cycle, correction values are determined for the offset

voltage of the sampled data comparator and any linearity and gain errors. These values are stored in internal

RAM and used during an analog-to-digital conversion to bring the overall full-scale, offset, and linearity errors

down to the specified limits. Full-scale error typically changes ±0.4 LSB over temperature and linearity error

changes even less; therefore it should be necessary to go through the calibration cycle only once after power up

if the Power Supply Voltage and the ambient temperature do not change significantly (see the curves in Typical

Performance Characteristics).

13.0 THE Auto Zero CYCLE

To correct for any change in the zero (offset) error of the ADC, the Auto Zero cycle can be used. It may be

necessary to do an Auto Zero cycle whenever the ambient temperature or the power supply voltage change

significantly. (See the curves, Figure 18 and Figure 20,inTypical Performance Characteristics.)

14.0 DYNAMIC PERFORMANCE

Many applications require the converter to digitize AC signals, but the standard DC integral and differential

nonlinearity specifications will not accurately predict the ADC's performance with AC input signals. The important

specifications for AC applications reflect the converter's ability to digitize AC signals without significant spectral

errors and without adding noise to the digitized signal. Dynamic characteristics such as signal-to-noise (S/N),

signal-to-noise + distortion ratio (S/(N + D)), effective bits, full power bandwidth, aperture time and aperture jitter

are quantitative measures of the ADC's capability.

An ADC's AC performance can be measured using Fast Fourier Transform (FFT) methods. A sinusoidal

waveform is applied to the ADC's input, and the transform is then performed on the digitized waveform. S/(N + D)

and S/N are calculated from the resulting FFT data, and a spectral plot may also be obtained. Typical values for

S/N are shown in Converter Electrical Characteristics, and spectral plots of S/(N + D) are included in Typical

Performance Characteristics.

The ADC's noise and distortion levels will change with the frequency of the input signal, with more distortion and

noise occurring at higher signal frequencies. This can be seen in the S/(N + D) versus frequency curves.

Effective number of bits can also be useful in describing the ADC's noise and distortion performance. An ideal

ADC will have some amount of quantization noise, determined by its resolution, and no distortion, which will yield

an optimum S/(N + D) ratio given by the following equation:

S/(N + D) = (6.02 × n + 1.76) dB

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ABC

CH0

CH1

CH2

CH3

CH4

CH5

CH6

CH7

COM

MUXOUT1

A/DIN1

MUXOUT2

A/DIN2

DGND

VD+

CCLK

SCLK

EOC

AGND

VREF+

VREF-

VA+

DOR

CONV RS-232

Interface

+4.096V

+5V

D Q

CLK

7474

1/6 74HC04 1/4 DS14C89

1/4 DS14C89

1/4 DS14C88

+5V

5 MHz

DTR

RTS

CTS

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

www.ti.com

SNAS080K –JULY 1999–REVISED MARCH 2013

where

• "n" is the ADC's resolution in bits (4)

The effective bits of an actual ADC is found to be:

n(effective) = ENOB = (S/(N + D) - 1.76 / 6.02 (5)

As an example, this device with a differential signed 5V, 1 kHz sine wave input signal will typically have a S/(N +

D) of 77 dB, which is equivalent to 12.5 effective bits.

15.0 AN RS232 SERIAL INTERFACE

Shown on the following page is a schematic for an RS232 interface to any IBM and compatible PCs. The DTR,

RTS, and CTS RS232 signal lines are buffered via level translators and connected to the ADC12038's DI, SCLK,

and DO pins, respectively. The D flip flop drives the CS control line.

Note: VA+, VD+, and VREF+on the ADC12038 each have 0.01 µF and 0.1 µF chip caps, and 10 µF tantalum caps. All

logic devices are bypassed with 0.1 µF caps.

Figure 72. Schematic for an RS232 Interface to any IBM and Compatible PCs

The assignment of the RS-232 port is shown below

B7 B6 B5 B4 B3 B2 B1 B0

Input Address 3FE X X X CTS X X X X

COM1 Output Address 3FC X X X 0 X X RTS DTR

A sample program, written in Microsoft QuickBasic, is shown on the next page. The program prompts for data

mode select instruction to be sent to the ADC. This can be found from the Mode Programming table shown

earlier. The data should be entered in “1”s and “0”s as shown in the table with DI0 first. Next, the program

prompts for the number of SCLK cycles required for the programmed mode select instruction. For instance, to

send all “0”s to the ADC, selects CH0 as the +input, CH1 as the −input, 12-bit conversion, and 13-bit MSB first

data output format (if the sign bit was not turned off by a previous instruction). This would require 13 SCLK

periods since the output data format is 13 bits.

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

SNAS080K –JULY 1999–REVISED MARCH 2013

www.ti.com

The ADC powers up with No Auto Cal, No Auto Zero, 10 CCLK Acquisition Time, 12-bit conversion, data out with

sign, power up, 12- or 13-bit MSB first, and user mode. Auto Cal, Auto Zero, Power Up and Power Down

instructions do not change these default settings. The following power up sequence should be followed:

1. Run the program

2. Prior to responding to the prompt apply the power to the ADC12038

3. Respond to the program prompts

It is recommended that the first instruction issued to the ADC12038 be Auto Cal (see Section 1.1 Interface

Concepts).

Code Listing:'variables DOL=Data Out word length, DI=Data string for ADC DI input,

' DO=ADC result string

'SET CS# HIGH

OUT &H3FC, (&H2 OR INP (&H3FC)) 'set RTS HIGH

OUT &H3FC, (&HFE AND INP(&H3FC)) 'set DTR LOW

OUT &H3FC, (&HFD AND INP(&H3FC)) 'set RTS LOW

OUT &H3FC, (&HEF AND INP(&H3FC)) 'set B4 low

LINE INPUT “DI data for ADC12038 (see Mode Table on data sheet)”; DI$

INPUT “ADC12038 output word length (8,9,12,13,16 or 17)”; DOL

'SET CS# HIGH

OUT &H3FC, (&H2 OR INP (&H3FC)) 'set RTS HIGH

OUT &H3FC, (&HFE AND INP(&H3FC)) 'set DTR LOW

OUT &H3FC, (&HFD AND INP(&H3FC)) 'set RTS LOW

'SET CS# LOW

OUT &H3FC, (&H2 OR INP (&H3FC)) 'set RTS HIGH

OUT &H3FC, (&H1 OR INP(&H3FC)) 'set DTR HIGH

OUT &H3FC, (&HFD AND INP(&H3FC)) 'set RTS LOW

DO$= “ ” 'reset DO variable

OUT &H3FC, (&H1 OR INP(&H3FC)) 'SET DTR HIGH

OUT &H3FC, (&HFD AND INP(&H3FC)) 'SCLK low

FOR N=1 TO 8

Temp$=MID$(DI$,N,1)

IF Temp$=“0” THEN

OUT &H3FC,(&H1 OR INP(&H3FC))

ELSE OUT &H3FC, (&HFE AND INP(&H3FC))

END IF 'out DI

OUT &H3FC, (&H2 OR INP(&H3FC)) 'SCLK high

IF (INP(&H3FE) AND 16)=16 THEN

DO$=DO$+“0”

ELSE

DO$=DO$+“1”

END IF 'input DO

OUT &H3FC, (&H1 OR INP(&H3FC)) 'SET DTR HIGH

OUT &H3FC, (&HFD AND INP(&H3FC)) 'SCLK low

NEXT N

IF DOL>8 THEN

FOR N=9 TO DOL

OUT &H3FC, (&H1 OR INP(&H3FC)) 'SET DTR HIGH

OUT &H3FC, (&HFD AND INP(&H3FC)) 'SCLK low

OUT &H3FC, (&H2 OR INP(&H3FC)) 'SCLK high

IF (INP(&H3FE) AND &H10)=&H10 THEN

DO$=DO$+“0”

ELSE

DO$=DO$+“1”

END IF

NEXT N

END IF

OUT &H3FC, (&HFA AND INP(&H3FC)) 'SCLK low and DI high

FOR N=1 TO 500

NEXT N

PRINT DO$

INPUT “Enter “C” to convert else “RETURN” to alter DI data”; s$

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

www.ti.com

SNAS080K –JULY 1999–REVISED MARCH 2013

IF s$=“C” OR s$=“c” THEN

GOTO 20

ELSE

GOTO 10

END IF

END

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

ADC12030, ADC12032, ADC12034

ADC12038, ADC12H030, ADC12H032

ADC12H034, ADC12H038

SNAS080K –JULY 1999–REVISED MARCH 2013

www.ti.com

REVISION HISTORY

Changes from Revision J (March 2013) to Revision K Page

• Changed layout of National Data Sheet to TI format .......................................................................................................... 42

Product Folder Links: ADC12030 ADC12032 ADC12034 ADC12038 ADC12H030 ADC12H032 ADC12H034

ADC12H038

PACKAGE OPTION ADDENDUM

www.ti.com 23-Jul-2017

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead/Ball Finish

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

ADC12030CIWM/NOPB OBSOLETE SOIC DW 16 TBD Call TI Call TI -40 to 85 ADC12030

CIWM

ADC12030CIWMX/NOPB OBSOLETE SOIC DW 16 TBD Call TI Call TI -40 to 85 ADC12030

CIWM

ADC12038CIWM NRND SOIC DW 28 26 TBD Call TI Call TI -40 to 85 ADC12038

CIWM

ADC12038CIWM/NOPB ACTIVE SOIC DW 28 26 Green (RoHS

& no Sb/Br) CU SN Level-3-260C-168 HR -40 to 85 ADC12038

CIWM

ADC12038CIWMX/NOPB ACTIVE SOIC DW 28 1000 Green (RoHS

& no Sb/Br) CU SN Level-3-260C-168 HR -40 to 85 ADC12038

CIWM

ADC12H034CIMSA/NOPB OBSOLETE SSOP DB 24 TBD Call TI Call TI ADC12H034

CIMSA

ADC12H034CIMSAX/NOPB OBSOLETE SSOP DB 24 TBD Call TI Call TI ADC12H034

CIMSA

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance

do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may

reference these types of products as "Pb-Free".

RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.

Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based

flame retardants must also meet the <=1000ppm threshold requirement.

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

PACKAGE OPTION ADDENDUM

www.ti.com 23-Jul-2017

Addendum-Page 2

(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish

value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

ADC12030CIWMX/NOPB SOIC DW 16 1000 330.0 16.4 10.9 10.7 3.2 12.0 16.0 Q1

ADC12038CIWMX/NOPB SOIC DW 28 1000 330.0 24.4 10.8 18.4 3.2 12.0 24.0 Q1

ADC12H034CIMSAX/NOP

BSSOP DB 24 2000 330.0 16.4 8.6 8.9 2.5 12.0 16.0 Q1

PACKAGE MATERIALS INFORMATION

www.ti.com 23-Sep-2013

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

ADC12030CIWMX/NOPB SOIC DW 16 1000 367.0 367.0 38.0

ADC12038CIWMX/NOPB SOIC DW 28 1000 367.0 367.0 45.0

ADC12H034CIMSAX/NOP

BSSOP DB 24 2000 367.0 367.0 38.0

PACKAGE MATERIALS INFORMATION

www.ti.com 23-Sep-2013

Pack Materials-Page 2

MECHANICAL DATA

MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE

4040065 /E 12/01

28 PINS SHOWN

Gage Plane

8,20

7,40

0,55

0,95

0,25

12,90

12,30

10,50

8,50

Seating Plane

9,907,90

10,50

9,90

0,38

5,60

5,00

0,22

2016

6,50

0,05 MIN

5,905,90

DIM

A MAX

A MIN

PINS **

2,00 MAX

6,90

7,50

0,65 M

0,15

0°–ā8°

0,10

0,09

0,25

NOTES: A. All linear dimensions are in millimeters.

B. This drawing is subject to change without notice.

C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.

D. Falls within JEDEC MO-150

IMPORTANT NOTICE

Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its

semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers

should obtain the latest relevant information before placing orders and should verify that such information is current and complete.

TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated

circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and

services.

Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is

accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced

documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements

different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the

associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.

Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers

remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have

full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products

used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with

respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous

consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and

take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will

thoroughly test such applications and the functionality of such TI products as used in such applications.

TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,

including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to

assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any

way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource

solely for this purpose and subject to the terms of this Notice.

TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI

products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,

enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically

described in the published documentation for a particular TI Resource.

Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that

include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE

TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY

RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or

endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR

REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO

ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL

PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,

INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF

PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,

DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN

CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949

and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.

Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such

products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards

and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must

ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in

life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.

Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life

support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all

medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.

TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).

Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications

and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory

requirements in connection with such selection.

Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-

compliance with the terms and provisions of this Notice.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265