Document Number: 82187 www.vishay.com
Rev. 2.1, 20-Jan-11 1
IR Receiver Modules for Remote Control Systems
TSOP362..
Vishay Semiconductors
MECHANICAL DATA
Pinning
1 = GND, 2 = GND, 3 = VS, 4 = OUT
DESCRIPTION
The TSOP362.. series are miniaturized SMD-IR receiver
modules for infrared remote control systems. PIN diode and
preamplifier are assembled on lead frame, the epoxy
package is designed as IR filter.
The demodulated output signal can directly be decoded by a
microprocessor. TSOP362.. is the standard IR remote
control SMD-receiver series, for 3 V supply voltage
supporting all major transmission codes.
This component has not been qualified according to
automotive specifications.
FEATURES
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Continuous data transmission possible
• TTL and CMOS compatibility
• Output active low
• Low power consumption
• High immunity against ambient light
• Supply voltage: 2.7 V to 5.5 V
• Compliant to RoHS Directive 2002/95/EC and in
accordance to WEEE 2002/96/EC
SPECIAL FEATURES
• Improved immunity against ambient light
• Suitable burst length ≥ 10 cycles/burst
• Taping available for topview and sideview assembly
BLOCK DIAGRAM APPLICATION CIRCUIT
16797
1234
PARTS TABLE
CARRIER FREQUENCY STANDARD APPLICATIONS (AGC2/AGC8)
30 kHz TSOP36230
33 kHz TSOP36233
36 kHz TSOP36236
36.7 kHz TSOP36237
38 kHz TSOP36238
40 kHz TSOP36240
56 kHz TSOP36256
30 kΩ
VS
OUT
Demo -
GND
pass
AGCInput
PIN
Band
dulator
Control circuit
3
4
1; 2
16839
C1=
4.7 µF
TSOPxxxx
GND
Circuit
µC
R1= 100 Ω
+ VS
GND
Transmitter
with
TSALxxxx
VS
R1 and C1 recommended to suppress power supply
disturbances. The output voltage should not be
hold continuously at a voltage below VO = 2.0 V
by the external circuit.
VO
17170
OUT
www.vishay.com Document Number: 82187
2Rev. 2.1, 20-Jan-11
TSOP362..
Vishay Semiconductors IR Receiver Modules for Remote
Control Systems
Note
• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability.
TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
Fig. 1 - Output Function Fig. 2 - Pulse Length and Sensitivity in Dark Ambient
ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified)
PARAMETER TEST CONDITION SYMBOL VALUE UNIT
Supply voltage (pin 3) VS- 0.3 to + 6 V
Supply current (pin 3) IS3mA
Output voltage (pin 1) VO- 0.3 to (VS + 0.3) V
Output current (pin 1) IO10 mA
Junction temperature Tj100 °C
Storage temperature range Tstg - 40 to + 100 °C
Operating temperature range Tamb - 25 to + 85 °C
Power consumption Tamb ≤ 85 °C Ptot 30 mW
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
Supply current Ev = 0 ISD 0.7 1.2 1.5 mA
Ev = 40 klx, sunlight ISH 1.3 mA
Supply voltage VS2.7 5.5 V
Transmission distance Ev = 0, test signal see fig. 1, IR diode TSAL6200,
IF = 250 mA d35m
Output voltage low IOSL = 0.5 mA, Ee = 0.7 mW/m2,
test signal see fig. 1 VOSL 250 mV
Minimum irradiance
(30 to 40 kHz)
VS = 3 V, pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1 Ee min. 0.35 0.5 W/m2
Minimum irradiance
(56 kHz)
VS = 3 V, pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1 Ee min. 0.4 0.6 W/m2
Minimum irradiance
(30 to 40 kHz)
VS = 5 V, pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1 Ee min. 0.45 0.6 W/m2
Minimum irradiance
(56 kHz)
VS = 5 V, pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1 Ee min. 0.5 0.7 W/m2
Maximum irradiance tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 3 Ee max. 30 W/m2
Directivity Angle of half transmission distance ϕ1/2 ± 45 deg
E
e
T
t
pi
*
t
* t
pi
10/f
0
is recommended for optimal function
V
O
V
OH
V
OL
t
16110
Optical Test Signal
(IR diode TSAL6200, I
F
= 0.4 A, 30 pulses, f = f
0
, t = 10 ms)
Output Signal
t
d1)
t
po 2)
1)
7/f
0
<t
d
<15/f
0
2)
t
pi
- 5/f
0
<t
po
< t
pi
+ 6/f
0
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
0.1 1 10 100 1000 10 000
Ee- Irradiance (mW/m²)
16908
Input Burst Duration
= 950 nm,
optical test signal, fig. 1
Output Pulse
t - Output Pulse Width (ms)
po
Document Number: 82187 www.vishay.com
Rev. 2.1, 20-Jan-11 3
TSOP362..
IR Receiver Modules for Remote
Control Systems Vishay Semiconductors
Fig. 3 - Output Function
Fig. 4 - Output Pulse Diagram
Fig. 5 - Frequency Dependence of Responsivity
Fig. 6 - Sensitivity in Bright Ambient
Fig. 7 - Sensitivity vs. Supply Voltage Disturbances
Fig. 8 - Sensitivity vs. Electric Field Disturbances
E
e
t
V
O
V
OH
V
OL
t
600 µs 600 µs
t = 60 ms
t
on
t
off
94 8134
Optical Test Signal
Output Signal, (see fig. 4)
T ,T - Output Pulse Width (ms)
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
0.1 1 10 100 1000 10 000
Ee- Irradiance (mW/m²)16909
Toff
= 950 nm,
optical test signal, fig. 3
Ton
on off
0.0
0.2
0.4
0.6
0.8
1.0
1.2
0.7 0.9 1.1 1.3
f/f0 - Relative Frequency16925
f = f0 ± 5 %
Δ f(3 dB) = f0/10
E /E - Rel. Responsivity
e min. e
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
0.01 0.1 1 10 100
E - Ambient DC Irradiance (W/m
2
)
16911
Correlation with ambient light sources:
10 W/m21.4 klx (Std.illum.A, T= 2855 K)
10 W/m28.2 klx (Daylight, T= 5900 K)
Ambient, = 950 nm
E
e min.
- Threshold Irradiance (mW/m
2
)
E
e min.
- Threshold Irradiance (mW/m²)
0.0 0.4 0.81.2 1.6
0.0
0.4
0.8
1.2
2.0
E - Field Strength of Disturbance (kV/m)
2.0
94 8147
1.6
f(E) = f
0
www.vishay.com Document Number: 82187
4Rev. 2.1, 20-Jan-11
TSOP362..
Vishay Semiconductors IR Receiver Modules for Remote
Control Systems
Fig. 9 - Max. Envelope Duty Cycle vs. Burstlength
Fig. 10 - Sensitivity vs. Ambient Temperature
Fig. 11 - Relative Spectral Sensitivity vs. Wavelength
Fig. 12 - Directivity
Fig. 13 - Sensitivity vs. Supply Voltage
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
020406080 100 120
Burst Length (number of cycles/burst)
16913
f = 38 kHz, E
e
= 2 mW/m
2
Max. Envelope Duty Cycle
0.0
0.1
0.2
0.3
0.4
0.5
0.6
- 30 - 15 0 15 30 45 60 75 90
Tamb- Ambient Temperature (°C)16918
Sensitivity in dark ambient
E - Threshold Irradiance (mW/m²)
e min.
0.0
0.2
0.4
0.6
0.8
1.0
1.2
750 850 950 1050 1150
λ-Wavelength (nm)
16919
S ( ) - Relative Spectral Sensitivityλrel
16801
0.4 0.2 0 0.2 0.4 0.6
0.6
0.9
0°
30°
10° 20°
40°
50°
60°
70°
80°
1.0
0.8
0.7
drel - Relative Transmission Distance
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
VS - Supply Voltage (V)17185
E - Sensitivity (mW/m )
2
e min.
Document Number: 82187 www.vishay.com
Rev. 2.1, 20-Jan-11 5
TSOP362..
IR Receiver Modules for Remote
Control Systems Vishay Semiconductors
SUITABLE DATA FORMAT
The circuit of the TSOP362.. is designed so that unexpected
output pulses due to noise or disturbance signals are
avoided. A bandpass filter, an integrator stage and an
automatic gain control are used to suppress such
disturbances.
The distinguishing mark between data signal and
disturbance signal are carrier frequency, burst length and
duty cycle.
The data signal should fulfill the following conditions:
• Carrier frequency should be close to center frequency of
the bandpass (e.g. 38 kHz)
• Burst length should be 10 cycles/burst or longer
• After each burst which is between 10 cycles and 70 cycles
a gap time of at least 14 cycles is necessary
• For each burst which is longer than 1.8 ms a corresponding
gap time is necessary at some time in the data stream.
This gap time should be at least 6 times longer than the
burst
• Up to 800 short bursts per second can be received
continuously
Some examples for suitable data format are: NEC code
(repetitive pulse), NEC code (repetitive data), Toshiba
Micom Format, Sharp code, RC5 Code, RC6 code,
R-2000 code, Sony code.
When a disturbance signal is applied to the TSOP362.. it can
still receive the data signal. However the sensitivity is
reduced to that level that no unexpected pulses will occur.
Some examples for such disturbance signals which are
suppressed by the TSOP362.. are:
• DC light (e.g. from tungsten bulb or sunlight)
• Continuous signal at 38 kHz or at any other frequency
• Signals from fluorescent lamps with electronic ballast with
high or low modulation (see fig. 14 or fig.15)
Fig. 14 - IR Signal from Fluorescent Lamp with Low Modulation
Fig. 15 - IR Signal from Fluorescent Lamp with High Modulation
0101520
Time (ms)
16920
IR Signal
5
0101520
Time (ms)
16921
IR Signal
5
www.vishay.com Document Number: 82187
6Rev. 2.1, 20-Jan-11
TSOP362..
Vishay Semiconductors IR Receiver Modules for Remote
Control Systems
PACKAGE DIMENSIONS in millimeters
ASSEMBLY INSTRUCTIONS
Reflow Soldering
• Reflow soldering must be done within 72 h while stored
under a max. temperature of 30 °C, 60 % RH after opening
the dry pack envelope
• Set the furnace temperatures for pre-heating and heating
in accordance with the reflow temperature profile as shown
in the diagram. Excercise extreme care to keep the
maximum temperature below 260 °C. The temperature
shown in the profile means the temperature at the device
surface. Since there is a temperature difference between
the component and the circuit board, it should be verified
that the temperature of the device is accurately being
measured
• Handling after reflow should be done only after the work
surface has been cooled off
Manual Soldering
• Use a soldering iron of 25 W or less. Adjust the
temperature of the soldering iron below 300 °C
• Finish soldering within 3 s
• Handle products only after the temperature has cooled off
2.35
R 1.7
5.51
0.5 ± 0.15
3 x 1.27 = 3.81
2.6
7.5
7.2
4x
1.27
5.3
2.9
4
2.2
Pick and place area. TR taping
2.2
3 x 1.27 = 3.81
1.27 0.9
2.8
specifications
according to DIN
technical drawings
Not indicated tolerances ± 0.3
Pick and place area. TT taping
Footprint
(1.5)
(1.4)
Issue: 8; 02.09.09
16776
Drawing-No.: 6.544-5341.01-4
A
A
0.1
0.1
0.3
0.4
14
Document Number: 82187 www.vishay.com
Rev. 2.1, 20-Jan-11 7
TSOP362..
IR Receiver Modules for Remote
Control Systems Vishay Semiconductors
VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE
TAPING VERSION TSOP..TT DIMENSIONS in millimeters
0
50
100
150
200
250
300
0 50 100 150 200 250 300
t (s)
T (°C)
255 °C
240 °C 245 °
C
max. 260 °C
max. 120 s max. 100 s
217 °C
max. 20 s
max. Ramp Up 3 °C/s max. Ramp Down 6 °C/s
max. 2 cycles allowed
19800
16584
www.vishay.com Document Number: 82187
8Rev. 2.1, 20-Jan-11
TSOP362..
Vishay Semiconductors IR Receiver Modules for Remote
Control Systems
TAPING VERSION TSOP..TR DIMENSIONS in millimeters
16585
Document Number: 82187 www.vishay.com
Rev. 2.1, 20-Jan-11 9
TSOP362..
IR Receiver Modules for Remote
Control Systems Vishay Semiconductors
REEL DIMENSIONS in millimeters
LEADER AND TRAILER DIMENSIONS in millimeters
COVER TAPE PEEL STRENGTH
According to DIN EN 60286-3
0.1 Nto 1.3 N
300 ± 10 mm/min.
165° to 180° peel angle
LABEL
Standard bar code labels for finished goods
The standard bar code labels are product labels and used for
identification of goods. The finished goods are packed in final
packing area. The standard packing units are labeled with
standard bar code labels before transported as finished
goods to warehouses. The labels are on each packing unit
and contain Vishay Semiconductor GmbH specific data.
16734
Trailer Leader
no devices
min. 200 min. 400
StartEnd
devices
96 11818
no devices
www.vishay.com Document Number: 82187
10 Rev. 2.1, 20-Jan-11
TSOP362..
Vishay Semiconductors IR Receiver Modules for Remote
Control Systems
DRY PACKING
The reel is packed in an anti-humidity bag to protect the
devices from absorbing moisture during transportation and
storage.
FINAL PACKING
The sealed reel is packed into a cardboard box. A secondary
cardboard box is used for shipping purposes.
RECOMMENDED METHOD OF STORAGE
Dry box storage is recommended as soon as the aluminum
bag has been opened to prevent moisture absorption. The
following conditions should be observed, if dry boxes are not
available:
• Storage temperature 10 °C to 30 °C
• Storage humidity ≤ 60 % RH max.
After more than 72 h under these conditions moisture
content will be too high for reflow soldering.
In case of moisture absorption, the devices will recover to the
former condition by drying under the following condition:
192 h at 40 °C + 5 °C/- 0 °C and < 5 % RH (dry air/nitrogen)
or
96 h at 60 °C + 5 °C and < 5 % RH for all device containers or
24 h at 125 °C + 5 °C not suitable for reel or tubes.
An EIA JEDEC standard JSTD-020 level 4 label is included
on all dry bags.
EIA JEDEC standard JSTD-020 level 4 label is included
on all dry bags
VISHAY SEMICONDUCTOR GmbH STANDARD BAR CODE PRODUCT LABEL (finished goods)
PLAIN WRITING ABBREVIATION LENGTH
Item-description - 18
Item-number INO 8
Selection-code SEL 3
LOT-/serial-number BATCH 10
Data-code COD 3 (YWW)
Plant-code PTC 2
Quantity QTY 8
Accepted by ACC -
Packed by PCK -
Mixed code indicator MIXED CODE -
Origin xxxxxxx+ Company logo
LONG BAR CODE TOP TYPE LENGTH
Item-number N 8
Plant-code N 2
Sequence-number X 3
Quantity N 8
Total length - 21
SHORT BAR CODE BOTTOM TYPE LENGTH
Selection-code X 3
Data-code N 3
Batch-number X 10
Filter - 1
Total length - 17
Aluminum bag
Label
Reel
15973
CAUTION
This bag contains
MOISTURE-SENSITIVE DEVICES
1. Shelf life in sealed bag: 12 months at < 40 °C and < 90 % relative
humidity (RH)
2. After this bag is opened, devices that will be subjected to soldering
reflow or equivalent processing (peak package body temp. 260 °C)
must be
2a. Mounted within 72 hours at factory condition of < 30 °C/60 % RH or
2b. Stored at < 5 % RH
3. Devices require baking befor mounting if:
Humidity Indicator Card is > 10 % when read at 23 °C ± 5 °C or
2a. or 2b. are not met.
4. If baking is required, devices may be baked for:
192 hours at 40 °C + 5 °C/- 0 °C and < 5 % RH (dry air/nitrogen) or
96 hours at 60 °C ± 5 °C and < 5 % RH for all device containers or
24 hours at 125 °C ± 5 °C not suitable for reels or tubes
Bag Seal Date:
(If blank, see barcode label)
Note: Level and body temperature defined by EIA JEDEC Standard JSTD-020
4
LEVEL
22522
Document Number: 82187 www.vishay.com
Rev. 2.1, 20-Jan-11 11
TSOP362..
IR Receiver Modules for Remote
Control Systems Vishay Semiconductors
ESD PRECAUTION
Proper storage and handling procedures should be followed
to prevent ESD damage to the devices especially when they
are removed from the antistatic shielding bag. Electro-static
sensitive devices warning labels are on the packaging.
VISHAY SEMICONDUCTORS STANDARD
BAR CODE LABELS
The Vishay Semiconductors standard bar code labels are
printed at final packing areas. The labels are on each
packing unit and contain Vishay Semiconductors specific
data.
16962
Document Number: 91000 www.vishay.com
Revision: 11-Mar-11 1
Disclaimer
Legal Disclaimer Notice
Vishay
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.