Type 735P, Metallized Polypropylene Film Capacitors
High Frequency, Wrap and Fill
The 735P series is designed and manufactured for use in many
demanding power applications. They are non-inductively wound
using the most reliable metallized polypropylene lm available.
A wide range of capacitance values, voltage ratings, lead
terminations and sizes oer the designer an array of options to
best meet the form, t and function requirements specied.
Highlights
- Excellent AC performance
- Low power dissipation
- Low dielectric absorption
- Low ESR
- Close tolerance
- High stability
- High ripple to 30 A
- Compliant to RoHS directive 2002/95/EC
Specications
Capacitance Range 1.0 to 30.0 µF
Capacitance Tolerance ±10%, ±5%
DC Rated Voltage 100 WVdc to 400 WVdc
Operating Temperature Range –55 ºC to 105 ºC
ESR 20 kHz to 100 kHz
Dissipation Factor 0.1% maximum - Measure all units at 1000 Hz, at +25 ºC
ΔV/ ΔT: 10 V/ms maximum
Insulation Resistance Measured at 100 WVDC after a 2 min charge:
At +25 ºC: 200 000 MΩ/µF or 400 000 MΩ minimum
DC Voltage Test 200% of rated voltage for 2 minutes
Vibration Test (Condition B) No mechanical damage, short, open or intermittent circuits
DC Life Test 140% of rated voltage for 1000 h at +105 ºC.
No open or short circuits. No visible damage.
Maximum Δ CAP ±1.0%
Minimum IR = 50% of initial limit
Maximum DF = 0.10%
Humidity Test 95% relative humidity at +40 ºC for 250 h.
No visible damage.
Maximum Δ CAP ±1.0%
Minimum IR = 20% of initial limit
Maximum DF = 0.12%
Physical Characteristics Pull Test
Wire Leads: 5 lb (2.3 g) for one min. No physical damage.
Terminal Lugs: -10 lb (4.5 kg) for one min. No physical damage.
Lead Bend: After three complete consecutive bend. No damage.
Marking: Type or part number, capacitance and voltage.
RoHS Compliant
CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830
CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830
735P 106 X 5 2 XXX
CDE Type
Number
Capacitance in µF
10 µF
Tolerance
5 = ±5%
9 = ±10%
Voltage
1 = 100 Vdc
2 = 250 Vdc
4 = 400 Vdc
Special
Construction
Part Numbering System
Type 735P, Metallized Polypropylene Film Capacitors
High Frequency, Wrap and Fill
Dimensions
1 & 2 µF 100 Vdc ratings are No. 22 AWG wire .025 [.635] Nominal Diameter
D Max < .700 [17.78], No. 20 AWG wire .032 [.812] Nominal Diameter
D Max ≥ .700 [17.78], No. 18 AWG wire .040 [1.016] Nominal Diameter
0.032
ESR
(mΩ)
20 Khz
to
100 Khz
Maximum Ripple Current
(Arms ) at 20 Khz
Case Temperature (2) atCase Size
CAPACITANCE Catalog Part D L +25°C +35°C +45°C +55°C +65°C +75°C +85°C
(μF) Number Inches [MM] Inches [MM]
100 VDC
1.0 735P105X9100L 0.531 [13.49] 0.750 [19.05] 15.0 9.2 8.5 7.8 7.0 6.0 4.9 4.5
2.0 735P205X9100L 0.596 [15.14] 0.938 [23.81] 12.0 10.8 10.0 9.1 8.2 7.0 5.8 5.3
3.0 735P305X9100L 0.717 [18.21] 0.938 [23.81] 11.0 12.1 11.2 10.3 9.2 8.0 6.5 5.9
5.0 735P505X9100L 0.733 [18.62] 1.250 [31.75] 10.0 13.8 12.7 11.6 10.4 9.0 7.4 6.7
10.0 735P106X9100L 0.898 [22.81] 1.500 [38.10] 9.0 15.0 15.0 14.2 12.7 11.0 9.0 8.2
20.0 735P206X9100L 1.000 [25.40] 2.250 [57.15] 8.0 15.0 15.0 15.0 15.0 13.6 11.1 10.0
30.0 735P306X9100L 1.200 [30.48] 2.250 [57.15] 6.0 15.0 15.0 15.0 15.0 15.0 12.4 11.4
200 VDC
1.0 735P105X9200L 0.512 [13.01] 1.250 [31.75] 20.0 7.3 7.3 7.3 7.3 7.2 5.9 5.4
2.0 735P205X9200L 0.698 [17.73] 1.250 [31.75] 15.0 12.0 12.0 11.3 10.1 8.7 7.1 6.5
3.0 735P305X9200L 0.747 [18.97] 1.500 [38.10] 13.0 15.0 13.8 12.6 11.3 9.8 8.0 7.3
5.0 735P505X9200L 0.862 [21.89] 1.750 [44.45] 11.0 15.0 15.0 14.7 13.1 11.4 9.3 8.5
10.0 735P106X9200L 1.030 [26.16] 2.250 [57.15] 9.0 15.0 15.0 15.0 15.0 13.8 11.3 10.3
20.0 735P206X9200L 1.440 [36.58] 2.250 [57.15] 6.0 15.0 15.0 15.0 15.0 15.0 14.1 12.8
400 VDC
1.0 735P105X9400L 0.713 [18.11] 1.500 [38.10] 19.0 9.5 9.5 9.5 9.5 9.5 7.8 7.1
2.0 735P205X9400L 0.895 [22.73] 1.750 [44.45] 15.0 15.0 15.0 15.0 13.4 11.6 9.5 8.7
3.0 735P305X9400L 1.086 [27.58] 1.750 [44.45] 12.0 15.0 15.0 15.0 15.0 13.1 10.7 9.8
5.0 735P505X9400L 1.192 [30.28] 2.250 [57.15] 10.0 15.0 15.0 15.0 15.0 15.0 12.5 11.4
10.0 735P106X9400L 1.668 [42.37] 2.250 [57.15] 6.0 15.0 15.0 15.0 15.0 15.0 15.0 14.1
Terminal Style H - Units with Terminal Lugs
100 VDC
1.0 735P105X9100H 0.531 [13.49] 0.875 [22.23] 15.0 10.3 9.5 8.7 7.8 6.7 5.5 5.0
2.0 735P205X9100H 0.596 [15.14] 1.062 [26.97] 12.0 12.0 11.0 10.0 8.9 7.8 6.3 5.8
3.0 735P305X9100H 0.717 [18.21] 1.062 [26.97] 11.0 13.3 12.3 11.2 10.0 8.7 7.1 6.5
5.0 735P505X9100H 0.733 [18.62] 1.375 [34.93] 10.0 14.8 13.7 12.5 11.2 9.7 7.9 7.2
10.0 735P106X9100H 0.898 [22.81] 1.625 [41.28] 9.0 17.8 16.5 15.0 13.5 11.7 9.5 8.7
20.0 735P206X9100H 1.000 [25.40] 2.375 [60.33] 8.0 21.6 20.0 18.3 16.4 14.2 11.6 10.6
30.0 735P306X9100H 1.200 [30.48] 2.375 [60.33] 6.0 24.3 22.5 20.5 18.4 15.9 13.0 11.9
200 VDC
1.0 735P105X9200H 0.512 [13.00] 1.375 [34.93] 20.0 7.3 7.3 7.3 7.3 7.3 6.4 5.8
2.0 735P205X9200H 0.698 [17.73] 1.375 [34.93] 15.0 14.3 13.3 12.1 10.8 9.4 7.7 7.0
3.0 735P305X9200H 0.747 [18.97] 1.625 [41.28] 13.0 15.9 14.7 13.5 12.0 10.4 8.5 7.8
5.0 735P505X9200H 0.862 [21.89] 1.875 [47.63] 11.0 18.3 17.0 15.5 13.9 12.0 9.8 8.9
10.0 735P106X9200H 1.030 [26.16] 2.375 [60.33] 9.0 22.4 20.7 18.9 16.9 14.6 12.0 10.9
20.0 735P206X9200H 1.440 [36.58] 2.375 [60.33] 6.0 27.4 25.4 23.2 20.7 17.9 14.7 13.4
400 VDC
1.0 735P105X9400H 0.713 [18.11] 1.625 [41.28] 19.0 9.5 9.5 9.5 9.5 9.5 8.3 7.5
2.0 735P205X9400H 0.895 [22.73] 1.875 [47.63] 15.0 15.0 15.0 15.0 14.2 12.3 10.0 9.1
3.0 735P305X9400H 1.086 [27.58] 1.875 [47.63] 12.0 21.1 19.5 17.8 15.9 13.8 11.3 10.3
5.0 735P505X9400H 1.192 [30.28] 2.375 [60.33] 10.0 24.4 22.6 20.6 18.5 16.0 13.1 11.9
10.0 735P106X9400H 1.668 [42.37] 2.375 [60.33] 6.0 30.0 27.8 25.4 22.7 19.7 16.1 14.7
CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830
735P 106 X 5 2 XXX
CDE Type
Number
Capacitance in µF
10 µF
Tolerance
5 = ±5%
9 = ±10%
Voltage
1 = 100 Vdc
2 = 250 Vdc
4 = 400 Vdc
Special
Construction
Type 735P, Metallized Polypropylene Film Capacitors
High Frequency, Wrap and Fill
Notes: (1) Part Numbers listed are for a capacitance tolerance of ± 10 %. To speciy ± 5 % tolerance, change the “X9” in the Part Number to “X5”. (2) The peak current pulse
capability ot these capacitors is 10 A/μF. The maximum rate voltage change is 10 V/μs.• Other capacitance values and voltage ratings are available upon request
Notice and Disclaimer: All product drawings, descriptions, specications, statements, information and
data (collectively, the “Information”) in this datasheet or other publication are subject to change. The
customer is responsible for checking, conrming and verifying the extent to which the Information con-
tained in this datasheet or other publication is applicable to an order at the time the order is placed. All
Information given herein is believed to be accurate and reliable, but it is presented without any guaran-
tee, warranty, representation or responsibility of any kind, expressed or implied. Statements of suitability
for certain applications are based on the knowledge that the Cornell Dubilier company providing such
statements (“Cornell Dubilier”) has of operating conditions that such Cornell Dubilier company regards
as typical for such applications, but are not intended to constitute any guarantee, warranty or representa-
tion regarding any such matter – and Cornell Dubilier specically and expressly disclaims any guarantee,
warranty or representation concerning the suitability for a specic customer application, use, storage,
transportation, or operating environment. The Information is intended for use only by customers who
have the requisite experience and capability to determine the correct products for their application. Any
technical advice inferred from this Information or otherwise provided by Cornell Dubilier with reference
to the use of any Cornell Dubilier products is given gratis (unless otherwise specied by Cornell Dubilier),
and Cornell Dubilier assumes no obligation or liability for the advice given or results obtained. Although
Cornell Dubilier strives to apply the most stringent quality and safety standards regarding the design
and manufacturing of its products, in light of the current state of the art, isolated component failures may
still occur. Accordingly, customer applications which require a high degree of reliability or safety should
employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies
or other appropriate protective measures) in order to ensure that the failure of an electrical component
does not result in a risk of personal injury or property damage. Although all product-related warnings,
cautions and notes must be observed, the customer should not assume that all safety measures are indi-
cated in such warnings, cautions and notes, or that other safety measures may not be required.