1.5 GHz to 2.4 GHz RF Vector Modulator AD8341 FUNCTIONAL BLOCK DIAGRAM FEATURES VPRF QBBP QBBM VPS2 90 RFOP RFIP RFIM RFOM 0 CMOP IBBP IBBM DSOP 04700-001 Cartesian amplitude and phase modulation 1.5 GHz to 2.4 GHz frequency range Continuous magnitude control of -4.5 dB to -34.5 dB Continuous phase control of 0 to 360 Output third-order intercept 17.5 dBm Output 1 dB compression point 8.5 dBm Output noise floor -150.5 dBm/Hz @ full gain Adjustable modulation bandwidth up to 230 MHz Fast output power disable 4.75 V to 5.25 V single-supply voltage Figure 1. APPLICATIONS RF PA linearization/RF predistortion Amplitude and phase modulation Variable attenuators and phase shifters CDMA2000, WCDMA, GSM/EDGE linear power amplifiers Smart antennas GENERAL DESCRIPTION The AD8341 vector modulator performs arbitrary amplitude and phase modulation of an RF signal. Since the RF signal path is linear, the original modulation is preserved. This part can be used as a general-purpose RF modulator, a variable attenuator/phase shifter, or a remodulator. The amplitude can be controlled from a maximum of -4.5 dB to less than -34.5 dB, and the phase can be shifted continuously over the entire 360 range. For maximum gain, the AD8341 delivers an OP1dB of 8.5 dBm, an OIP3 of 17.5 dBm, and an output noise floor of -150.5 dBm/Hz, independent of phase. It operates over a frequency range of 1.5 GHz to 2.4 GHz. The baseband inputs in Cartesian I and Q format control the amplitude and phase modulation imposed on the RF input signal. Both I and Q inputs are dc-coupled with a 500 mV differential full-scale range. The maximum modulation bandwidth is 230 MHz, which can be reduced by adding external capacitors to limit the noise bandwidth on the control lines. Both the RF inputs and outputs can be used differentially or single-ended and must be ac-coupled. The RF input and output impedances are nominally 50 over the operating frequency range. The DSOP pin allows the output stage to be disabled quickly in order to protect subsequent stages from overdrive. The AD8341 operates off supply voltages from 4.75 V to 5.25 V while consuming approximately 125 mA. The AD8341 is fabricated on Analog Devices' proprietary, high performance 25 GHz SOI complementary bipolar IC process. It is available in a 24-lead, Pb-free LFCSP package and operates over a -40C to +85C temperature range. Evaluation boards are available. Rev. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.326.8703 (c) 2004 Analog Devices, Inc. All rights reserved. AD8341 TABLE OF CONTENTS Specifications..................................................................................... 3 Applications..................................................................................... 12 Absolute Maximum Ratings............................................................ 4 Using the AD8341 ...................................................................... 12 ESD Caution.................................................................................. 4 RF Input and Matching ............................................................. 12 Pin Configuration and Function Descriptions............................. 5 RF Output and Matching .......................................................... 13 Typical Performance Characteristics ............................................. 6 Driving the I-Q Baseband Controls......................................... 13 Theory of Operation ...................................................................... 10 Interfacing to High Speed DACs.............................................. 14 RF Quadrature Generator ......................................................... 10 CDMA2000 Application............................................................ 14 I-Q Attenuators and Baseband Amplifiers.............................. 11 WCDMA Application ................................................................ 15 Output Amplifier ........................................................................ 11 Evaluation Board ............................................................................ 17 Noise and Distortion.................................................................. 11 Outline Dimensions ....................................................................... 20 Gain and Phase Accuracy.......................................................... 11 Ordering Guide .......................................................................... 20 RF Frequency Range .................................................................. 11 REVISION HISTORY 7/04--Revision 0: Initial Version Rev. 0 | Page 2 of 20 AD8341 SPECIFICATIONS VS = 5 V, TA = 25C, ZO = 50 , f = 1.9 GHz, single-ended, ac-coupled source drive to RFIP through 1.2 nH series inductor, RFIM ac-coupled through 1.2 nH series inductor to common, differential-to-single-ended conversion at output using 1:1 balun. Table 1. Parameter OVERALL FUNCTION Frequency Range Maximum Gain Minimum Gain Gain Control Range Phase Control Range Gain Flatness Group Delay Flatness RF INPUT STAGE Input Return Loss CARTESIAN CONTROL INTERFACE (I AND Q) Gain Scaling Modulation Bandwidth Second Harmonic Distortion Third Harmonic Distortion Step Response Recommended Common-Mode Level RF OUTPUT STAGE Output Return Loss f = 1.9 GHz Gain Output Noise Floor Output IP3 Adjacent Channel Power Output 1 dB Compression Point POWER SUPPLY Positive Supply Voltage Total Supply Current OUTPUT DISABLE Disable Threshold Attenuation Enable Response Time Disable Response Time Conditions Min Typ Max Unit 2.4 -4.5 -34.5 GHz dB dB 30 360 0.5 50 dB Degrees dB ps 12 dB 2 230 41 47 45 1/V MHz dBc dBc ns 45 ns 0.5 V 7.5 dB -4.5 -150.5 -149 17.5 -76 dB dBm/Hz dBm/Hz dBm dBm 8.5 dBm 1.5 Maximum gain setpoint for all phase setpoints VBBI = VBBQ = 0 V differential (at recommended common-mode level) Relative to maximum gain Over 30 dB control range Over any 60 MHz bandwidth Over any 60 MHz bandwidth RFIM, RFIP (Pins 21 and 22) From RFIP to CMRF (with 1.2 nH series inductors) IBBP, IBBM, QBBP, QBBM (Pins 16, 15, 3, 4) 500 mV p-p, sinusoidal baseband input single-ended 500 mV p-p, 1 MHz, sinusoidal baseband input differential 500 mV p-p, 1 MHz, sinusoidal baseband input differential For gain setpoint from 0.1 to 0.9 (VBBP = 0.5 V, VBBM = 0.55 V to 0.95 V) For gain setpoint from 0.9 to 0.1 (VBBP = 0.5 V, VBBM = 0.95 V to 0.55 V) RFOP, RFOM (Pins 9, 10) Measured through balun Maximum gain setpoint Maximum gain setpoint, no input PIN = 0 dBm, frequency offset = 20 MHz f1 = 1900 MHz, f2 = 1897.5 MHz, maximum gain setpoint CDMA2000, single carrier, POUT = -4 dBm, maximum gain, phase setpoint = 45 (See Figure 35) Maximum gain VPS2 (Pins 5, 6, and 14), VPRF (Pins 19 and 24), RFOP, RFOM (Pins 9 and 10) Includes load current DSOP (Pin 13) (See Figure 24) DSOP = 5 V Delay following high-to-low transition until RF output amplitude is within 10% of final value. Delay following low-to-high transition until device produces full attenuation Rev. 0 | Page 3 of 20 4.75 105 5 125 5.25 145 V mA Vs/2 33 30 V dB ns 15 ns AD8341 ABSOLUTE MAXIMUM RATINGS Table 2. Parameters Supply Voltage VPRF, VPS2 DSOP IBBP, IBBM, QBBP, QBBM RFOP, RFOM RF Input Power at Maximum Gain (RFIP or RFIM, Single-Ended Drive) Equivalent Voltage Internal Power Dissipation JA (With Pad Soldered to Board) Maximum Junction Temperature Operating Temperature Range Storage Temperature Range Lead Temperature Range (Soldering 60 sec) Rating 5.5 V 5.5 V 2.5 V 5.5V 13 dBm, re: 50 Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2.8 V p-p 825 mW 59 C/W 125C -40C to +85C -65C to +150C 300C ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. 0 | Page 4 of 20 AD8341 24 VPRF 23 CMRF 22 RFIP 21 RFIM 20 CMRF 19 VPRF PIN CONFIGURATION AND FUNCTION DESCRIPTIONS PIN 1 INDICATOR AD8341 TOP VIEW (Not to Scale) 18 IFLP 17 IFLM 16 IBBP 15 IBBM 14 VPS2 13 DSOP 04700-002 1 2 3 4 5 6 CMOP 7 CMOP 8 RFOP 9 RFOM 10 CMOP 11 CMOP 12 QFLP QFLM QBBP QBBM VPS2 VPS2 Figure 2. 24-Lead Lead Frame Chip Scale Package (LFCSP) Table 3. Pin Function Descriptions Pin No. 1, 2 Mnemonic QFLP, QFLM 3, 4 5, 6, 14, 19, 24 7, 8, 11, 12, 20, 23 9, 10 13 15, 16 17, 18 QBBP, QBBM VPS2, VPRF CMOP, CMRF RFOP, RFOM DSOP IBBM, IBBP IFLM, IFLP 21, 22 RFIM, RFIP Function Q Baseband Input Filter Pins. Connect optional capacitor to reduce Q baseband channel low-pass corner frequency. Q Channel Differential Baseband Inputs. Positive Supply Voltage. 4.75 V - 5.25 V. Device Common. Connect via lowest possible impedance to external circuit common. Differential RF Outputs. Must be ac-coupled. Differential impedance 50 nominal. Output disable. Pull high to disable output stage. I Channel Differential Baseband Inputs. I Baseband Input Filter Pins. Connect optional capacitor to reduce I baseband channel low-pass corner frequency. Differential RF Inputs. Must be ac-coupled. Differential impedance 50 nominal. Rev. 0 | Page 5 of 20 AD8341 TYPICAL PERFORMANCE CHARACTERISTICS 1.0 0 GAIN SETPOINT = 1.0 PHASE SETPOINT = 0 0.5 PHASE SETPOINT = 270 -15 PHASE SETPOINT = 180 -20 PHASE SETPOINT = 90 -25 -30 04700-003 -35 -40 0 0.1 0.2 0.3 0.4 0.5 0.6 GAIN SETPOINT 0.7 0.8 0.9 0 -0.5 -1.0 -1.5 -2.0 GAIN SETPOINT = 0.25 -2.5 -3.0 -3.5 GAIN SETPOINT = 0.1 -4.0 -4.5 1.0 0 6 180 225 270 315 360 360 315 4 PHASE SETPOINT = 270 3 GAIN SETPOINT = 0.25 270 PHASE SETPOINT = 0 2 GAIN SETPOINT = 0.5 PHASE (Degrees) PHASE SETPOINT = 45 1 0 -1 PHASE SETPOINT = 225 -2 -3 PHASE SETPOINT = 90 -4 PHASE SETPOINT = 180 -5 -6 PHASE SETPOINT = 135 -8 0 0.1 0.2 0.3 225 GAIN SETPOINT = 0.1 GAIN SETPOINT = 1.0 180 135 90 45 04700-004 GAIN CONFORMANCE ERROR (dB) 135 Figure 6. Gain Conformance Error vs. Phase Setpoint at Different Gain Setpoints, RF Frequency = 1900 MHz PHASE SETPOINT = 315 -7 0.4 0.5 0.6 GAIN SETPOINT 0.7 0.8 0.9 0 0 1.0 Figure 4. Gain Conformance Error vs. Gain Setpoint at Different Phase Setpoints, RF Frequency = 1900 MHz 45 90 135 180 225 270 PHASE SETPOINT (Degrees) 315 360 Figure 7. Phase vs. Phase Setpoint at Different Gain Setpoints, RF Frequency = 1900 MHz 25 -2 GAIN SETPOINT = 0.1 GAIN SETPOINT = 1.0 -4 20 -6 PHASE ERROR (Degrees) -8 GAIN SETPOINT = 0.5 -12 -14 GAIN SETPOINT = 0.25 -16 -18 -20 -22 GAIN SETPOINT = 0.1 -26 -28 0 45 90 135 180 225 270 315 GAIN SETPOINT = 0.25 10 5 0 GAIN SETPOINT = 0.5 GAIN SETPOINT = 1.0 -5 -10 04700-005 -24 15 04700-008 -10 GAIN (dB) 90 PHASE SETPOINT (Degrees) Figure 3. Gain Magnitude vs. Gain Setpoint at Different Phase Setpoints, RF Frequency = 1900 MHz 5 45 04700-007 GAIN (dB) -10 GAIN SETPOINT = 0.5 04700-006 GAIN CONFORMANCE ERROR (dB) -5 -15 0 360 PHASE SETPOINT (Degrees) 45 90 135 180 225 270 PHASE SETPOINT (Degrees) 315 360 Figure 8. Phase Error vs. Phase Setpoint at Different Gain Setpoints, RF Frequency = 1900 MHz Figure 5. Gain Magnitude vs. Phase Setpoint at Different Gain Setpoints, RF Frequency = 1900 MHz Rev. 0 | Page 6 of 20 AD8341 -147 0 -1 -148 -40C -2 RF PIN = +5dBm +25C -3 RF PIN = 0dBm GAIN (dB) -150 -151 04700-009 0.2 0.3 0.4 0.5 0.6 GAIN SETPOINT 0.7 0.8 0.9 -9 -10 1500 1.0 Figure 9. Output Noise Floor vs. Gain Setpoint, Noise in dBm/Hz, No Carrier, and With 1900 MHz Carrier (Measured at 20 MHz Offset) Pin = -5, 0, and +5 dBm -8 GAIN (dB) 2200 2300 2400 FUNDAMENTAL POWER, 1899MHz, 1900MHz GAIN SETPOINT = 0.5 GAIN SETPOINT = 0.25 -14 -16 -18 -20 1800 1900 2000 2100 FREQUENCY (MHz) 0 -10 -12 1700 GAIN SETPOINT = 1.0 -4 -6 1600 Figure 12. Gain Magnitude vs. Frequency and Temperature, Maximum Gain, Phase Setpoint = 0 RF OUTPUT AM SIDEBAND POWER (dBm) 0 -2 04700-012 -8 -154 0.1 -6 -7 NO RF INPUT -153 0 -5 +85C RF PIN = -5dBm -152 -4 GAIN SETPOINT = 0.1 -22 04700-010 -24 -26 -28 1500 1600 1700 1800 1900 2000 2100 2200 2300 -10 -20 -30 -40 -50 -60 -70 -80 THIRD BASEBAND HARMONIC PRODUCT, 1897MHz, 1903MHz -90 -100 100 2400 SECOND BASEBAND HARMONIC PRODUCT, 1898MHz, 1902MHz 200 300 400 500 600 700 800 900 04700-013 NOISE (dBm/Hz) -149 1000 DIFFERENTIAL BB LEVEL (mV p-p) FREQUENCY (MHz) Figure 13. Baseband Harmonic Distortion (I and Q Channel, RF Input = 0 dBm, Output Balun and Cable Losses of Approximately 2 dB Not Accounted for in Plot) Figure 10. Gain vs. Frequency at Different Gain Setpoints, Phase Setpoint = 0 12 -146 -40C -147 10 +25C 8 OP1dB (dBm) -149 -150 -151 6 +85C 4 -152 -154 1500 1600 1700 1800 1900 2000 2100 FREQUENCY (MHz) 2200 2300 0 1500 2400 04700-014 2 -153 04700-011 NOISE (dBm/Hz) -148 1600 1700 1800 1900 2000 2100 FREQUENCY (MHz) 2200 2300 2400 Figure 14. Output 1 dB Compression Point vs. Frequency and Temperature, Maximum Gain, Phase Setpoint = 0 Figure 11. Output Noise Floor vs. Frequency, Maximum Gain, No RF Carrier, Phase Setpoint = 0 Rev. 0 | Page 7 of 20 AD8341 20 25 GAIN SETPOINT = 1.0 -40C 15 20 GAIN SETPOINT = 0.5 +25C OIP3 (dBm) OIP3 (dBm) 10 15 +85C 10 GAIN SETPOINT = 0.25 5 0 GAIN SETPOINT = 0.1 5 1600 1700 1800 1900 2000 2100 FREQUENCY (MHz) 2200 2300 04700-018 0 1500 04700-015 -5 -10 2400 0 45 90 135 180 Figure 15. Output IP3 vs. Frequency and Temperature, Maximum Gain, Phase Setpoint = 0, 2.5 MHz Carrier Spacing 270 315 360 Figure 18. Output IP3 vs. Gain and Phase Setpoints, RF Frequency = 1900 MHz, 2.5 MHz Carrier Spacing -10 1V p-p BB INPUT 0 RBW 30kHz VBW 30kHz SWT 100ms REF LVL 0dBm RF ATT 20dB UNIT dBm A -15 -30 60 110 160 210 260 FREQUENCY (MHz) 310 360 -60 -70 -80 410 1SA 04700-019 -35 10 -50 SECOND BASEBAND HARMONIC 250mV p-p BB INPUT -40 UNDESIRED SIDEBAND OUTPUT POWER (dBm) -25 -30 RF FEEDTHROUGH -20 -20 DESIRED SIDEBAND 500mV p-p BB INPUT SECOND BASEBAND HARMONIC -10 04700-016 RF OUTPUT AM SIDEBAND POWER (dBm) 225 PHASE SETPOINT (Degrees) -90 -100 CENTER 1.9GHz 500kHz/ SPAN 5MHz FREQUENCY (MHz) Figure 16. I/Q Modulation Bandwidth vs. Baseband Magnitude 10 Figure 19. Single-Sideband Performance, RF Frequency = 1900 MHz, RF Input = -10 dBm; 1 MHz, 500 mV p-p Differential BB Drive 90 GAIN SETPOINT = 1.0 60 120 5 30 150 0 GAIN SETPOINT = 0.25 -5 0 180 1500MHz -10 210 GAIN SETPOINT = 0.1 45 90 135 180 330 225 270 315 360 240 PHASE SETPOINT (Degrees) 300 270 Figure 17. Output 1 dB Compression Point vs. Gain and Phase Setpoints, RF Frequency = 1900 MHz S11 RF PORT WITH 1.2nH INDUCTORS S11 RF PORT WITHOUT INDUCTORS Figure 20. Input Impedance Smith Chart Rev. 0 | Page 8 of 20 04700-020 -15 0 2400MHz 04700-017 OP1dB (dBm) GAIN SETPOINT = 0.5 AD8341 90 0 -5 60 120 RF OUTPUT POWER (dBm) -10 30 0 180 1500MHz 2400MHz 210 -20 -25 -30 -35 -40 -45 330 04700-024 150 -15 -50 -55 0 240 300 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 DSOP VOLTAGE (V) 04700-021 270 SDD22 PORT DIFFERENTIAL S22 WITH 1 TO 1 TRANSFORMER Figure 24. Output Disable Attenuation, RF Frequency = 1900 MHz, RF Input = -5 dBm Figure 21. Output Impedance Smith Chart 0 2V/DIV DSOP -20 3 PHASE SETPOINT = 0 VOLTS -30 -40 RF OUTPUT PHASE SETPOINT = 45 -50 4 100mV/DIV 04700-022 -60 PHASE SETPOINT = 90 -70 0 0.1 0.2 0.3 0.4 0.5 0.6 GAIN SETPOINT 0.7 0.8 0.9 CH3 2.0V CH4 100mV M10.0ns 5.0GS/s A CH3 TIME (10ns/DIV) 1.0 Figure 25. Output Disable Response Time, RF Frequency = 1900 MHz, RF Input = 0 dBm Figure 22. Phase Error vs. Gain Setpoint by Phase Setpoint, RF Frequency = 1900 MHz 127 VPOS = 5.00V 125 VPOS = 5.25V 124 123 VPOS = 4.75V 122 121 -40 -30 -20 -10 04700-023 SUPPLY CURRENT (mA) 126 0 10 20 30 40 TEMPERATURE (C) 50 60 70 80 Figure 23. Supply Current vs. Temperature Rev. 0 | Page 9 of 20 04700-025 PHASE ERROR (Degrees) -10 1.84V AD8341 THEORY OF OPERATION By controlling the relative amounts of I and Q components that are summed, continuous magnitude and phase control of the gain is possible. Consider the vector gain representation of the AD8341 expressed in polar form in Figure 27. The attenuation factors for the I and Q signal components are represented on the x- and y-axis, respectively, by the baseband inputs, VBBI and VBBQ. The resultant of their vector sum represents the vector gain, which can also be expressed as a magnitude and phase. By applying different combinations of baseband inputs, any vector gain within the unit circle can be programmed. Pure amplitude modulation is represented by radial movement of the gain vector tip at a fixed angle, while pure phase modulation is represented by rotation of the tip around the circle at a fixed radius. Unlike traditional I-Q modulators, the AD8341 is designed to have a linear RF signal path from input to output. Traditional I-Q modulators provide a limited LO carrier path through which any amplitude information is removed. VBBI I CHANNEL INPUT LINEAR ATTENUATOR V-I SINGLE-ENDED OR DIFFERENTIAL 50 INPUT Z 0/90 SINGLE-ENDED OR DIFFERENTIAL 50 OUTPUT I-V V-I OUTPUT DISABLE LINEAR ATTENUATOR 04700-026 The AD8341 is a linear RF vector modulator with Cartesian baseband controls. In the simplified block diagram given in Figure 26, the RF signal propagates from the left to the right while baseband controls are placed above and below. The RF input is first split into in-phase (I) and quadrature (Q) components. The variable attenuators independently scale the I and Q components of the RF input. The attenuator outputs are then summed and buffered to the output. Q CHANNEL INPUT VBBQ Figure 26. Simplified Architecture of the AD8341 A change in sign of VBBI or VBBQ can be viewed as a change in sign of the gain or as a 180 phase change. The outermost circle represents the maximum gain magnitude of unity. The circle origin implies, in theory, a gain of 0. In practice, circuit mismatches and unavoidable signal feedthrough limit the minimum gain to approximately -34.5 dB. The phase angle between the resultant gain vector and the positive x-axis is defined as the phase shift. Note that there is a nominal, systematic insertion phase through the AD8341 to which the phase shift is added. In the following discussions, the systematic insertion phase is normalized to 0. Vq MAX GAIN +0.5 A |A| +0.5 MIN GAIN -0.5 The correspondence between the desired gain and phase setpoints, GainSP and PhaseSP, and the Cartesian inputs, VBBI and VBBQ, is given by simple trigonometric identities GainSP = [(VBBI /VO )2 + (VBBQ /VO )2 ] PhaseSP = arctan(VBBQ /VBBI ) where: VO is the baseband scaling constant (500 mV). VBBI and VBBQ are the differential I and Q baseband voltages, respectively. Note that when evaluating the arctangent function, the proper phase quadrant must be selected. For example, if the principal value of the arctangent (known as the Arctangent(x)) is used, quadrants 2 and 3 could be interpreted mistakenly as quadrants 4 and 1, respectively. In general, both VBBI and VBBQ are needed in concert to modulate the gain and the phase. Vi 04700-027 -0.5 Figure 27. Vector Gain Representation RF QUADRATURE GENERATOR The RF input is directly coupled differentially or single-ended to the quadrature generator, which consists of a multistage RC polyphase network tuned over the operating frequency range of 1.5 GHz to 2.4 GHz. The recycling nature of the polyphase network generates two replicas of the input signal, which are in precise quadrature, i.e., 90, to each other. Since the passive network is perfectly linear, the amplitude and phase information contained in the RF input is transmitted faithfully to both channels. The quadrature outputs are then separately buffered to drive the respective attenuators. The characteristic impedance of the polyphase network is used to set the input impedance of the AD8341. Rev. 0 | Page 10 of 20 AD8341 I-Q ATTENUATORS AND BASEBAND AMPLIFIERS GAIN AND PHASE ACCURACY The proprietary linear-responding attenuator structure is an active solution with differential inputs and outputs that offer excellent linearity, low noise, and greater immunity from mismatches than other variable attenuator methods. The gain, in linear terms, of the I and Q channels is proportional to its control voltage with a scaling factor designed to be 2/V, i.e., a full-scale gain setpoint of 1.0 (-4.5 dB) for a VBBI (or a VBBQ) of 500 mV. The control voltages can be driven differentially or single-ended. The combination of the baseband amplifiers and attenuators allows for maximum modulation bandwidths in excess of 200 MHz. There are numerous ways to express the accuracy of the AD8341. Ideally, the gain and phase should precisely follow the setpoints. Figure 4 illustrates the gain error in dB from a best fit line, normalized to the gain measured at the gain setpoint = 1.0, for the different phase setpoints. Figure 6 shows the gain error in a different form, normalized to the gain measured at phase setpoint = 0; the phase setpoint is swept from 0 to 360 for different gain setpoints. Figure 8 and Figure 22 show analogous errors for the phase error as a function of gain and phase setpoints. The accuracy clearly depends on the region of operation within the vector gain unit circle. Operation very close to the origin generally results in larger errors as the relative accuracy of the I and Q vectors degrades. OUTPUT AMPLIFIER The output amplifier accepts the sum of the attenuator outputs and delivers a differential output signal into the external load. The output pins must be pulled up to an external supply, preferably through RF chokes. When the 50 load is taken differentially, an output P1dB and IP3 of 8.5 dBm and 17.5 dBm is achieved, respectively, at 1.9 GHz. The output can be taken in single-ended fashion, albeit at lower performance levels. NOISE AND DISTORTION The output noise floor and distortion levels vary with the gain magnitude but do not vary significantly with the phase. At the higher gain magnitude setpoints, the OIP3 and the noise floor vary in direct proportion with the gain. At lower gain magnitude setpoints, the noise floor levels off while the OIP3 continues to vary with the gain. RF FREQUENCY RANGE The frequency range on the RF input is limited by the internal polyphase quadrature phase-splitter. The phase-splitter splits the incoming RF input into two signals, 90 out of phase, as previously described in the RF Quadrature Generator section. This polyphase network has been designed to ensure robust quadrature accuracy over standard fabrication process parameter variations for the 1.5 GHz to 2.4 GHz specified RF frequency range. Using the AD8341 as a single-sideband modulator and measuring the resulting sideband suppression is a good gauge of how well the quadrature accuracy is maintained over RF frequency. A typical plot of sideband suppression from 1.1 GHz to 2.7 GHz is shown in Figure 28. The level of sideband suppression degradation outside the 1.5 GHz to 2.4 GHz specified range will be subject to manufacturing process variations. -20 -25 -30 -35 -40 -45 0.7 04700-028 SIDEBAND SUPPRESSION (dBc) -15 0.9 1.1 1.3 1.5 1.7 1.9 2.1 2.3 FREQUENCY (GHz) Figure 28. Sideband Suppression vs. Frequency Rev. 0 | Page 11 of 20 2.5 2.7 AD8341 APPLICATIONS loss of >10 dB over the operating frequency range. Different matching inductors can improve matching over a narrower frequency range. The single-ended and differential input impedances are exactly the same. USING THE AD8341 The AD8341 is designed to operate in a 50 impedance system. Figure 30 illustrates an example where the RF input is driven in a single-ended fashion while the differential RF output is converted to a single-ended output with an RF balun. The baseband controls for the I and Q channels are typically driven from differential DAC outputs. The power supplies, VPRF and VPS2, should be bypassed appropriately with 0.1 F and 100 pF capacitors. Low inductance grounding of the CMOP and CMRF common pins is essential to prevent unintentional peaking of the gain. 100pF 1.2nH RFIM ~1VDC RC PHASE RF 04700-029 100pF 1.2nH RFIP 50 Figure 29. RF Input Interface to the AD8341 Showing Coupling Capacitors and Matching Inductors RF INPUT AND MATCHING The RFIP and RFIM should be ac-coupled through low loss series capacitors as shown in Figure 29. The internal dc levels are at approximately 1 V. For single-ended operation, one input is driven by the RF signal while the other input is ac grounded. The input impedance of the AD8341 is defined by the characteristics of the polyphase network. The capacitive component of the network causes its impedance to roll-off with frequency albeit at a rate slower than 6 dB/octave. By using matching inductors on the order of 1.2 nH in series with each of the RF inputs, RFIP and RFIM, a 50 match is achieved with a return VP C2 100pF C1 0.1F IBBM VP IBBP C12 (SEE TEXT) C6 100pF VPS2 OUTPUT DISABLE DSOP CMOP CMRF CMOP RFIM RFOM C17 100pF AD8341 RFOP CMRF CMOP VPRF C3 0.1F C4 100pF QFLP VPS2 VP RFIP QBBM L4 1.2nH QBBP C5 100pF QFLM RF INPUT L3 1.2nH IFLP VPRF IBBM VP IBBP C7 100pF B IFLM C8 0.1F A L1 120nH ETC1-1-13 RF OUTPUT C18 L2 100pF 120nH CMOP VPS2 C14 0.1F VP C10 0.1F QBBP QBBM C9 100pF Figure 30. Basic Connections Rev. 0 | Page 12 of 20 04700-030 C11 (SEE TEXT) AD8341 -2.5 RF OUTPUT AND MATCHING RL2 = SHORT -3.0 The RF outputs of the AD8341, RFOP, and RFOM, are open collectors of a transimpedance amplifier which need to be pulled up to the positive supply, preferably with RF chokes as shown in Figure 31. The nominal output impedance looking into each individual output pin is 25 . Consequently, the differential output impedance is 50 . -3.5 -4.0 GAIN (dB) -4.5 -5.0 RL2 = 50 -5.5 -6.0 -6.5 VP -7.0 GM 100pF 1.0 1:1 100pF RF OUTPUT 04700-031 50 DIFFERENTIAL 1.2 1.4 1.6 1.8 2.0 2.2 2.4 FREQUENCY (GHz) 2.6 2.8 3.0 Figure 32. Gain of the AD8341 Using a Single-Ended Output with Different Dummy Loads, RL2 , on the Unused Output RFOP RT RL = 50 -8.5 RFOM ISIG -8.0 120nH RT 04700-032 RL2 = OPEN -7.5 Figure 31. RF Output Interface to the AD8341 Showing Coupling Capacitors, Pull-Up RF Chokes, and Balun Since the output dc levels are at the positive supply, ac coupling capacitors will usually be needed between the AD8341 outputs and the next stage in the system. A 1:1 RF broadband output balun, such as the ETC1-1-13 (M/A-COM), converts the differential output of the AD8341 into a single-ended signal. Note that the loss and balance of the balun directly impact the apparent output power, noise floor, and gain/phase errors of the AD8341. In critical applications, narrow-band baluns with low loss and superior balance are recommended. If the output is taken in a single-ended fashion directly into a 50 load through a coupling capacitor, there will be an impedance mismatch. This can be resolved with a 1:2 balun to convert the single-ended 25 output impedance to 50 . If loss of signal swing is not critical, a 25 back termination in series with the output pin can also be used. The unused output pin must still be pulled up to the positive supply. The user may load it through a coupling capacitor with a dummy load to preserve balance. The gain of the AD8341 when the output is singleended varies slightly with dummy load value as shown in Figure 32. The RF output signal can be disabled by raising the DSOP pin to the positive supply. The output disable function provides >30 dB attenuation of the input signal even at full gain. The interface to DSOP is high impedance and the shutdown and turn-on response times are <100 ns. If the disable function is not needed, the DSOP pin should be tied to ground. DRIVING THE I-Q BASEBAND CONTROLS The I and Q inputs to the AD8341 set the gain and phase between input and output. These inputs are differential and should normally have a common-mode level of 0.5 V. However, when differentially driven, the common mode can vary from 250 mV to 750 mV while still allowing full gain control. Each input pair has a nominal input swing of 0.5 V differential around the common-mode level. The maximum gain of unity is achieved if the differential voltage is equal to +500 mV or -500 mV. So with a common-mode level of 500 mV, IBBP and IBBM will each swing between 250 mV and 750 mV. The I and Q inputs can also be driven with a single-ended signal. In this case, one side of each input should be tied to a low noise 0.5 V voltage source (a 0.1 F decoupling capacitor located close to the pin is recommended), while the other input swings from 0 V to 1 V. Differential drive generally offers superior even-order distortion and lower noise than single-ended drive. The bandwidth of the baseband controls exceeds 200 MHz even at full-scale baseband drive. This allows for very fast gain and phase modulation of the RF input signal. In cases where lower modulation bandwidths are acceptable or desired, external filter capacitors can be connected across Pins IFLP to IFLM and QFLP to QFLM to reduce the ingress of baseband noise and spurious signal into the control path. Rev. 0 | Page 13 of 20 f3dB 45 kHz x 10 nF C FLT + 0.5 pF This equation has been verified for values of CFLT from 10 pF to 0.1 F (bandwidth settings of approximately 4.5 kHz to 43 MHz). INTERFACING TO HIGH SPEED DACs The AD977x family of dual DACs is well suited to driving the I and Q vector controls of the AD8341. While these inputs can in general be driven by any DAC, the differential outputs and bias level of the ADI TxDAC(R) family allows for a direct connection between DAC and modulator. The AD977x family of dual DACs has differential current outputs. The full-scale current is user programmable and is usually set to 20 mA, that is, each output swings from 0 mA to 20 mA. The basic interface between the AD9777 DAC outputs and the AD8341 I and Q inputs is shown in Figure 33. The Resistors R1 and R2 set the dc bias level according to the equation: Bias Level = Average Output Current x R1 For example, if the full-scale current from each output is 20 mA, each output will have an average current of 10 mA. Therefore to set the bias level to the recommended 0.5 V, R1 and R2 should be set to 50 each. R1 and R2 should always be equal. If R3 is omitted, this will result in an available swing from the DAC of 2 V p-p differential, which is twice the maximum voltage range required by the AD8341. DAC resolution can be maximized by adding R3, which scales down this voltage according to the following equation: Full Scale Swing = Figure 34. Peak-to-Peak DAC Output Swing vs. Swing Scaling Resistor R3 (R1 = R2 = 50 ) Figure 34 shows the relationship between the value of R3 and the peak baseband voltage with R1 and R2 equal to 50 . From Figure 34, it can be seen that a value of 100 for R3 will provide a peak-to-peak swing of 1 V p-p differential into the AD8341's I and Q inputs. When using a DAC, low-pass image reject filters are typically used to eliminate the Nyquist images produced by the DAC. They also provide the added benefit of eliminating broadband noise that might feed into the modulator from the DAC. CDMA2000 APPLICATION To test the compliance to the CDMA2000 base station standard, a single-carrier CDMA2000 test model signal (forward pilot, sync, paging, and six traffic as per 3GPP2 C.S0010-B, Table 6.5.2.1) was applied to the AD8341 at 1960 MHz. A cavity tuned filter was used to reduce noise from the signal source being applied to the device. The 6.8 MHz pass band of this filter is apparent in the subsequent spectral plots. Figure 35 shows a plot of the spectrum of the output signal under nominal conditions. POUT is equal to -4 dBm and VBBI = VBBQ = 0.353 V, i.e., VIBBP - VIBBM = VQBBP - VQBBM = 0.353 V. Noise and distortion is measured in a 1 MHz bandwidth at 2.25 MHz carrier offset (30 kHz measurement bandwidth). R2 2 x I MAX (R1 || (R2 + R3)) x 1 - R2 + R3 AD9777 AD8341 IBBP IOUTA1 R1 R2 OPTIONAL LOW-PASS FILTER R3 IOUTB1 IBBM IOUTA2 QBBP R1 R2 OPTIONAL LOW-PASS FILTER R3 IOUTB2 1.15 1.13 1.10 1.08 1.05 1.02 1.00 0.97 0.95 0.92 0.90 0.88 0.85 0.82 0.80 0.77 0.75 0.72 0.70 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 () 04700-034 The 3 dB bandwidth is set by choosing CFLT according to the following equation: DIFFERENTIAL PEAK-TO-PEAK SWING (V) AD8341 04700-033 QBBM Figure 33. Basic AD9777 to AD8341 Interface Rev. 0 | Page 14 of 20 RBW 30kHz VBW 100kHz SWT 500ms 1 0.3dB OFFSET 1 [T1] -20 CH PWR ACP UP ACP LOW -30 RF ATT 0dB 0 -60 -5 -65 -10 -70 -15 -75 -20 -80 -25 -85 UNIT dBm -18.47dBm 1.95999900GHz -4.06dBm -77.64dBm -76.66dBm A -40 1AVG 1RM -50 -60 -70 -80 C0 C0 -90 C11 CU1 -112 CU1 04700-035 -100 CENTER 1.96Hz 1MHz/ -30 Holding the differential I and Q control voltages steady at 0.353 V, input power was swept. Figure 36 shows variation in spurious content, again measured at 2.25 MHz carrier offset in a 1 MHz bandwidth, as defined by the 3GPP2 specification. -70 -72 -74 -76 -78 -80 0.2 0.3 0.4 IQ CONTROL VOLTAGE Figure 37 shows that for a fixed input power, the ACP (measured in dBm) tracks the output power as the gain is changed. WCDMA APPLICATION Figure 38 shows a plot of the output spectrum of the AD8341 transmitting a single-carrier WCDMA signal (Test Model 1-64 at 2140 MHz). The carrier power is approximately -9 dBm. The differential I and Q control voltages are both equal to 0.353 V, that is, the vector is sitting on the unit circle at 45. At this power level, an adjacent channel power ratio of -61 dBc is achieved. The alternate channel power ratio of -72 dBc is dominated by the noise floor of the AD8341. MARKER 1 [T1 ] -28.39dBm 2.14050000GHz REF LVL -24 -30 -84 -86 -24dBm RBW 30kHz VBW 300kHz SWT 1s 1 OFFSET 1dB 04700-036 -88 -16 -14 -12 -10 -8 -6 OUTPUT POWER (dBm) -4 -2 RF ATT 0dB UNIT dBm 1 [T1] -28.39dBm 2.14050000GHz CH PWR -8.95dBm ACP UP -60.78dB ACP LOW -60.82dB ALT1 UP -72.67dB ALT1 LOW -72.66dB -40 -18 0.5 Figure 37. Output Power and ACP vs. I and Q Control Voltages, CDMA2000 Test Model, VBBI = VBBQ, ACP Measured at 2.25 MHz Carrier Offset in 1 MHz BW -82 -90 -20 0.1 SPAN 10MHz Figure 35. Output Spectrum, 1960 MHz, Single-Carrier CDMA2000 Test Model at -4 dBm, VBBI = VBBQ = 0.353 V, Adjacent Channel Power Measured at 2.25 MHz Carrier Offset in 1 MHz BW Input Signal Filtered Using a Cavity Tuned Filter (Pass Band = 6.8 MHz) ACP @ 2.25MHz OFFSET (dBm, 1MHz, BW) -90 0 -50 1RM -60 0 A -70 Figure 36. Adjacent Channel Power vs. Output Power, CDMA2000 Single Carrier @ 1960 MHz; ACP Measured at 2.25 MHz Carrier Offset (1 MHz BW); VBBI = VBBQ = 0.353 V -80 -90 C0 -100 With a fixed input power of 2.4 dBm, the output power was again swept by exercising the I and Q inputs. VBBI and VBBQ were kept equal and were swept from 100 mV to 500 mV. The resulting output power and ACP are shown in Figure 37. C12 C12 C0 CU2 C11 -110 CU1 C11 -120 -124 04700-038 C11 ACP dBm (1MHz BW) @ 2.25MHz OFFSET -12 -12dBm OUTPUT POWER (dBm) MARKER 1 [T1 ] -18.47dBm 1.95999900GHz REF LVL 04700-037 AD8341 CU1 CENTER 2.14GHz 2.5MHz/ SPAN 25MHz Figure 38. AD8341 Single-Carrier WCDMA Spectrum at 2140 MHz Figure 39 shows how ACPR and noise vary with varying input power (differential I and Q control voltages are held at 0.353 V). At high power levels, both adjacent and alternate channel power ratios increase sharply. As output power drops, adjacent and alternate channel power ratios both reach minimums before the measurement becomes dominated by the noise floor of the AD8341. At this point, adjacent and alternate channel power ratios become approximately equal. Rev. 0 | Page 15 of 20 AD8341 0 -40 -60 -45 -65 ACPR 10MHz OFFSET -50 -70 -55 -75 -60 -80 -65 -85 -70 -90 -95 -75 NOISE -50MHz OFFSET -80 -30 -100 -25 -20 -15 -10 -5 OUTPUT POWER (dBm) 0 5 -10 -50 -15 -60 -25 -65 -70 -30 ACPR 10MHz OFFSET -35 -75 -40 -80 -45 -50 Figure 39. AD8341 ACPR and Noise vs. Output Power; Single-Carrier WCDMA (Test Model 1-64 at 2140 MHz) Figure 40 shows how output power, ACPR, and noise vary with the differential I and Q control voltages. VBBI and VBBQ are tied together and are varied from 0.5 V to 50 mV. -55 ACPR 5MHz OFFSET -20 -85 NOISE -50MHz OFFSET -90 0 0.1 0.2 0.3 0.4 IQ CONTROL VOLTAGE 04700-040 -55 ACPR 5MHz OFFSET -45 ACPR (dBc) NOISE dBm @ 50MHz OFFSET (1MHz BW) -35 OUTPUT POWER (dBm) -50 -40 OUTPUT POWER dBm -5 04700-039 -30 NOISE dBm @ 50MHz CARRIER OFFSET (1MHz BW) ADJACENT/ALTERNATE CHANNEL POWER RATIO (dBc) As the output power drops, the noise floor, measured in dBm in 1 MHz BW at 50 MHz carrier offset, drops slightly. 0.5 Figure 40. AD8341 Output Power, ACPR and Noise vs. VIQ. Single-Carrier WCDMA (Test Model 1-64 at 2140 MHz) In this case, adjacent channel power ratio remains constant as the (noise dominated) alternate channel power degrades roughly 1-for-1 with output power. As the I and Q control voltage drops, the noise floor again drops slowly. Rev. 0 | Page 16 of 20 AD8341 EVALUATION BOARD The evaluation board circuit schematic for the AD8341 is shown in Figure 41. The evaluation board is configured to be driven from a single-ended 50 source. Although the input of the AD8341 is differential, it may be driven single-ended, with no loss of performance. The low-pass corner frequency of the baseband I and Q channels can be reduced by installing capacitors in the C11 and C12 positions. The low-pass corner frequency for either channel is approximated by f3dB 45 kHz x 10 nF C FLT + 0.5 pF On this evaluation board, the I and Q baseband circuits are identical to each other, so the following description applies equally to each. The connections and circuit configuration for the Q baseband inputs are described in Table 4. The baseband input of the AD8341 requires a differential voltage drive. The evaluation board is set up to allow such a drive by connecting the differential voltage source to QBBP and QBBM. The common-mode voltage should be maintained at approximately 0.5 V. For this configuration, Jumpers W1 through W4 should be removed. The baseband input of the evaluation board may also be driven with a single-ended voltage. In this case, a bias level is provided to the unused input from Potentiometer R10 by installing either W1 or W2. Setting SW1 in Position B disables the AD8341 output amplifier. With SW1 set to Position A, the output amplifier is enabled. With SW1 set to Position A, an external voltage signal, such as a pulse, can be applied to the DSOP SMA connector to exercise the output amplifier enable/disable function. Table 4. Evaluation Board Configuration Options Components R7, R9, R11, R14, R15, R19, R20, R21, C15, C19, W3, W4 Function I Channel Baseband Interface. Resistors R7 and R9 may be installed to accommodate a baseband source that requires a specific terminating impedance. Capacitors C15 and C19 are bypass capacitors. For single-ended baseband drive, the Potentiometer R11 can be used to provide a bias level to the unused input (install either W3 or W4). R1, R3, R10, R12, R13, R16, R17, R18, C16, C20, W1, W2 Q Channel Baseband Interface. See the I Channel Baseband Interface section. C11, C12 Baseband Low-Pass Filtering. By adding Capacitor C11 between QFLP and QFLM, and C12 between IFLP and IFLM, the 3 dB low-pass corner frequency of the baseband interface can be reduced from 230 MHz (nominal). See equation in text. Output Interface. The 1:1 balun transformer, T1, converts the 50 differential output to 50 single-ended. C17 and C18 are dc blocks. L1 and L2 provide dc bias for the output. T1, C17, C18, L1, L2 L3, L4, C5, C6 Input Interface. The input impedance of the AD8341 requires 1.2 nH inductors in series with RFIP and RFIM for optimum return loss when driven by a single-ended 50 line. C5 and C6 are dc blocks. Rev. 0 | Page 17 of 20 Default Conditions R7, R9 = Not Installed R11 = Potentiometer, 2 k, 10 Turn (Bourns) R14 = 4 k (Size 0603) R15 = 44 k (Size 0603) R19, R20, R21 = 0 (Size 0603) C15, C19 = 0.1 F (Size 0603) W3 = Jumper (Installed) W4 = Jumper (Open) R1, R3 = Not Installed R10 = Potentiometer, 2 k, 10 Turn (Bourns) R12 = 4 k (Size 0603) R13 = 44 k (Size 0603) R16, R17, R18 = 0 (Size 0603) C16, C20 = 0.1 F (Size 0603) W1 = Jumper (Installed) W2 = Jumper (Open) C11, C12 = Not Installed C17, C18 = 100 pF (Size 0603) T1 = ETC1-1-13 (M/A-COM) L1, L2 = 120 nH (Size 0603) L3, L4 = 1.2 nH (Size 0402) C5, C6 = 100 pF (Size 0603) AD8341 Components C2, C4, C7, C9, C14, C1, C3, C8, C10, R2, R4, R5, R6 Function Supply Decoupling. R8, SW1 Output Disable Interface. The output stage of the AD8341 is disabled by applying a high voltage to the DSOP pin by moving SW1 to Position B. The output stage is enabled moving SW1 to Position A. The output disable function can also be exercised by applying an external high or low voltage to the DSOP SMA connector with SW1 in Position A. IBBP Default Conditions C2, C4, C7, C9, C14 = 0.1 F (Size 0603) C1, C3, C8, C10 = 100 pF (Size 0603) R2, R4, R5, R6 = 0 (Size 0603) R8 = 10 k (Size 0603) SW1 = SPDT (Position A, Output Enabled) IBBM C19 R7 0.1F (OPEN) R9 (OPEN) W4 R21 0 VP TEST POINT C2 0.1F R20 0 C15 0.1F R2 0 VS R14 4k GND TEST POINT R19 0 W3 R11 2k R15 44k C1 100pF C12 (OPEN) C6 100pF VPS2 IBBM IFLP VPRF IBBP VS C8 100pF R5 0 IFLM C7 0.1F SW1 CMRF L3 1.2nH R8 10k DSOP CMOP CMOP RFIN B A DSOP C18 100pF T1 ETC1-1-13 M/A-COM RFOM AD8341 RFIP L4 1.2nH C3 100pF QFLP C17 L1 100pF 120nH CMOP C14 0.1F VPS2 VP C11 (OPEN) C10 100pF R12 4k R10 2k R6 0 C9 0.1F R13 44k VS C16 0.1F W2 R17 0 R1 (OPEN) W1 R16 0 R18 0 R3 C20 (OPEN) 0.1F QBBP QBBM Figure 41. Evaluation Board Schematic Rev. 0 | Page 18 of 20 04700-041 R4 0 VPS2 VPRF C4 0.1F L2 120nH CMOP QBBM CMRF VP RFOP RFOP QBBP C5 100pF QFLM RFIN Figure 42. Component Side Layout 04700-043 04700-042 AD8341 Figure 43. Component Side Silkscreen Rev. 0 | Page 19 of 20 AD8341 OUTLINE DIMENSIONS 0.60 MAX 4.00 BSC SQ PIN 1 INDICATOR 0.60 MAX 0.50 BSC 3.75 BSC SQ TOP VIEW 0.50 0.40 0.30 1.00 0.85 0.80 12 MAX SEATING PLANE 0.80 MAX 0.65 TYP 0.30 0.23 0.18 PIN 1 INDICATOR 24 1 19 18 2.25 2.10 SQ 1.95 EXPOSED PAD (BOTTOM VIEW) 13 12 7 6 0.25 MIN 2.50 REF 0.05 MAX 0.02 NOM 0.20 REF COPLANARITY 0.08 COMPLIANT TO JEDEC STANDARDS MO-220-VGGD-2 Figure 44. 24-Lead Lead Frame Chip Scale Package [LFCSP] 4 mm x 4 mm Body (CP-24-1) Dimensions shown in millimeters ORDERING GUIDE Model AD8341ACPZ-WP1, 2 AD8341ACPZ-REEL72 AD8341-EVAL 1 2 Temperature Range -40C to +85C -40C to +85C Package Description 24-Lead Lead Frame Chip Scale Package (LFCSP) 24-Lead Lead Frame Chip Scale Package (LFCSP) Evaluation Board WP = Waffle pack. Z = Pb-free part. (c) 2004 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D04700-0-7/04(0) Rev. 0 | Page 20 of 20 Package Option CP-24-1 CP-24-1 Order Multiple 64 1,500 1