Series 1-DC
• D1D to D5D series SSRs; MOSFET output
• Ratings from 7A to 40A @ 200 VDC, and from 7A to 10A @ 500 VDC
• DC Contr o l
• Relays are easily paralleled for higher-current applications
• CE Compliant to EN60950-1
PRODUCT SELECTION
Load Voltage 7A 10A 12A 20A 40A
100 VDC D1D07 D1D12 D1D20 D1D40
200 VDC D2D07 D2D12 D2D40
400 VDC D4D07 D4D12
500 VDC D5D07 D5D10
OUTPUT SPECIFICATIONS (1)
Description 7A 12A 20A 40A 7A 12A 40A 7A 12A 7A 10A
Operating Voltage Range 0-100 0-100 0-100 0-100 0-200 0-200 0-200 0-400 0-400 0-500 0-500
Maximum Off-State Leakage Current @ Rated Voltage [mA] 0.1 0.2 0.3 0.3 0.1 0.3 0.3 0.3 0.3 0.2 0.3
Maximum Load Current (3) [Adc] 712 20 40 712 40 712 710
Minimum Load Current [mA] 11111111111
Maximum Surge Current [Adc] (10ms) 15 28 42 106 22 27 106 17 36 19 29
Maximum On-State Voltage Drop @ Rated Current [Vdc] 2.0 1.6 2.1 2.1 2.0 2.8 2.1 4.2 4.2 5.7 5.5
Thermal Resistance Junction to Case (Rjc ) [°C/W] 2.2 1.34 1.06 0.83 1.5 1.06 0.83 1.06 0.8 1.0 0.8
Maximum On-State Resistance [RDS-ON][Ohms] 0.29 0.13 0.10 0.05 0.29 0.23 0.05 0.6 0.35 0.8 0.55
INPUT SPECIFICATIONS (1)
Description DC Control
Control Voltage Range 3.5-32 VDC
Minimum Turn-On Voltage 3.5 VDC
Minimum T urn -Off Voltage 1.0 VDC
Minimum Input Current @ 5VDC 1.6 mA
Maximum Input Current @ 32VDC 28 mA
Nominal Input Impedance See Note 4
Maximum Turn-On Time [µsec] 100
Maximum Turn-Off Time [msec] 1.0
GENERAL SPECIFICATIONS
Description Parameters
Dielectric Strength, Input/Output/Base (50/60Hz) 2500 VRMS
Minimum Insulation Resistance (@ 500 V DC) 109 Ohm
Maximum Capacitance, Input/Output 50 pF
Ambient Operating Temperature Range -20 to 80°C
Ambient Storage Temperature Range -20 to 125 °C
Weight (typical) 3.0 oz (86.5g)
Encapsulation Ther ma lly conductive Epoxy
Terminals Screws and Saddle Clamps Furnished, Unmounted
Recommended Terminal Screw Torque Range: 6-32 Screws - 10 in lbs. 8-32 and 10-32 Screws -20 in. lbs. (Screws dry without grase)
GENERAL NOTES
1) All parameters at 25°C and per section unless otherwise specified.
2) Dielectric strength and insulation resistance are measured between input and output
3) Heat sinking required, for derating curves see page 3.
4) Input circuitry vers i o n incorporates acti ve current limiter.
MECHANICAL SPECIFICATIONS
THERMAL DERATE INFORMATION
WIRING DIAGRAM
MAXIMUM SURGE VS DURATION
AGENCY APPROVALS
EN60950 : Meets the requirements of sections1.5: 1,7: 2.9: 2.10.5.3: 4.2: 4.5: 4.7:
Designed in accordance with the requirements of IEC 62314
UL E116950 (100 Volt Models 1-DC Only )
Rev. 120711
ANNEX - ENVIROMENTAL INFORMATION