Semiconductor DG181 thru DG191 CT ODU ODUCT R P PR TE 45 OLE UTE April 1999 OBS UBSTIT 49, HI-51051 S 0 E I-5 IH5 SIBL G185: H I-5051, IH5043 POS H D 0 , , 9 3 , 03 84 Features DG1 90: DG4 043, HI-0 DG1 91: HI-5 * Constant ON-Resistance for Signals to 10V (DG182, DG1 High-Speed Drivers with JFET Switch Description The DG181 thru DG191 series of analog gates consist of 2 or 4 N-channel junction-type field-effect transistors (JFET) designed to function as electronic switches. Level-shifting drivers enable low-level inputs (0.8V to 2V) to control the ON-OFF state of each switch. The driver is designed to provide a turn-off speed which is faster than turn-on speed, so that break-before-make action is achieved when switching from one channel to another. In the ON state, each switch conducts current equally well in both directions. In the OFF condition, the switches will block voltages up to 20V peak-to-peak. Switch-OFF input-output isolation 50dB at 10MHz, due to the low output impedance of the FET-gate driving circuit. DG185, DG188, DG191), to 7.5V (All Devices) * 15V Power Supplies * <2nA Leakage from Signal Channel in Both ON and OFF States * TTL, DTL, RTL Direct Drive Compatibility * tON, tOFF <150ns, Break-Before-Make Action * Cross-Talk and Open Switch Isolation >50dB at 10MHz (75 Load) Functional Diagrams (Typical Channel) DG186, DG187, DG188 - ONE AND TWO CHANNEL SPDT AND SPST CIRCUIT CONFIGURATION VL DG183, DG184, DG185 - TWO CHANNEL DPST CIRCUIT CONFIGURATION VL V+ S1 D1 IN V+ S D IN S2 D2 GND S D GND V- V- CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper I.C. Handling Procedures. Copyright (c) Harris Corporation 1999 1 File Number 3114.4 DG181 Series Part Number Information (Continued) Part Number Information PART NUMBER TYPE RDS(ON) (MAX) PACKAGE PART NUMBER TYPE RDS(ON) (MAX) PACKAGE DG181AA Dual SPST 30 10 Lead CAN DG187AA SPDT 30 10 Lead CAN DG181AA/883B Dual SPST 30 10 Lead CAN DG187AA/883B SPDT 30 10 Lead CAN DG181AP Dual SPST 30 14 Lead SBDIP DG187AP SPDT 30 14 Lead SBDIP DG181AP/883B Dual SPST 30 14 Lead SBDIP DG187AP/883B SPDT 30 14 Lead SBDIP DG181BA Dual SPST 30 10 Lead CAN DG187BA SPDT 30 10 Lead CAN DG181BP Dual SPST 30 14 Lead SBDIP DG187BP SPDT 30 14 Lead SBDIP DG182AA Dual SPST 75 10 Lead CAN DG188AA SPDT 75 10 Lead CAN DG182AA/883B Dual SPST 75 10 Lead CAN DG188AA/883B SPDT 75 10 Lead CAN DG182AP Dual SPST 75 14 Lead SBDIP DG188AP SPDT 75 14 Lead SBDIP DG182AP/883B Dual SPST 75 14 Lead SBDIP DG188AP/883B SPDT 75 14 Lead SBDIP DG182BA Dual SPST 75 10 Lead CAN DG188BA SPDT 75 10 Lead CAN DG182BP Dual SPST 75 14 Lead SBDIP DG188BP SPDT 75 14 Lead SBDIP DG184AP Dual DPST 30 16 Lead SBDIP DG190AP Dual SPDT 30 16 Lead SBDIP DG184AP/883B Dual DPST 30 16 Lead SBDIP DG190AP/883B Dual SPDT 30 16 Lead SBDIP DG184BP Dual DPST 30 16 Lead SBDIP DG190BP Dual SPDT 30 16 Lead SBDIP DG185AP Dual DPST 75 16 Lead SBDIP DG191AP Dual SPDT 75 16 Lead SBDIP DG185AP/883B Dual DPST 75 16 Lead SBDIP DG191AP/883B Dual SPDT 75 16 Lead SBDIP DG185BP Dual DPST 75 16 Lead SBDIP DG191BP Dual SPDT 75 16 Lead SBDIP 2 DG181 Series Pinouts and Switching State Diagrams DUAL SPST - DG181, DG182 (TO-100 METAL CAN) TOP VIEW DUAL SPST - DG181, DG182 (CDIP) TOP VIEW S2 10 S1 1 9 D2 D1 2 8 IN2 IN1 3 7 V- 4 V+ 6 5 GND S1 1 14 S2 D1 2 13 D2 NC 3 12 NC NC 4 11 NC IN1 5 10 IN2 V+ 6 9 V- VL 7 8 GND VL DUAL DPST - DG184, DG185 (CDIP) TOP VIEW D1 1 16 S1 NC 2 15 IN1 D3 3 14 V- S3 4 13 GND S4 5 12 VL D4 6 11 V+ NC 7 10 IN2 D2 8 9 S2 SPDT - DG187, DG188 (TO-100 METAL CAN) TOP VIEW D2 10 D1 1 9 S2 S1 2 8 NC IN 3 7 V- 4 V+ 6 5 GND VL SPDT - DG187, DG188 (CDIP) TOP VIEW DUAL SPDT - DG190, DG191 (CDIP) TOP VIEW NC 1 14 NC D1 1 16 S1 NC 2 13 NC NC 2 15 IN1 D3 3 14 V- S3 4 13 GND S4 5 12 VL D4 6 11 V+ NC 7 10 IN2 D2 8 9 S2 D1 3 12 D2 S1 4 11 S2 IN 5 10 NC V+ 6 9 V- VL 7 8 GND 3 DG181 Series Absolute Maximum Ratings Thermal Information V+ - V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36V V+ - VD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33V VD - V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33V VD - VS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22V VL - V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36V VL - VIN, VL - GND, VIN - GND . . . . . . . . . . . . . . . . . . . . . . . . . . . 8V GND - V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27V GND - VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V Current (S or D) (Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200mA Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . -65oC to +150oC Lead Temperature (Soldering, 10s) . . . . . . . . . . . . . . . . . . . +300oC Operating Temperature . . . . . . . . . . . . . . . . . . . . . . -55oC to +125oC Maximum Power Dissipation TO Metal Can Packages . . . . . . . . . . . . . . . . . . . . . . . . . . 450mW Derate 6mW/ oC above +75oC Ceramic DIP Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . 825mW Derate 11mW/ oC above +75oC Device mounted with all leads welded or soldered to PC board. CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Electrical Specifications DEVICE NUMBER PARAMETER V+ = +15V, V- = -15V, VL = 5V, Unless Otherwise Specified (NOTE 1) TEST CONDITIONS A SERIES B SERIES -55oC +25oC +125oC -20oC +25oC +85oC UNITS SWITCH DG181, DG182, DG184, DG185, DG187, DG188, DG190, DG191 VS = 10V, VD = -10V, V+ = 10V, V- = -20V, VIN = "OFF" - 1 100 - 5 100 nA DG181, DG184, DG187, DG190 VS = 7.5V, VD = -7.5V, VIN = "OFF" - 1 100 - 5 100 nA DG182, DG185, DG188, DG191 VS = 10V, VD = -10V, VIN = "OFF" - 1 100 - 5 100 nA DG181, DG182, DG184, DG185, DG187, DG188, DG190, DG191 VS = 10V, VD = -10V, V+ = 10V, V- = -20V, VIN = "OFF" - 1 100 - 5 100 nA DG181, DG184, DG187, DG190 VS = 7.5V, VD = -7.5V, VIN = "OFF" - 1 100 - 5 100 nA DG182, DG185, DG188, DG191 VS = 10V, VD = -10V, VIN = "OFF" - 1 100 - 5 100 nA DG181, DG184, DG187, DG190 VD = VS = -7.5V, VIN = "ON" - 2 -200 - -10 -200 nA DG182, DG185, DG188, DG191 VD = VS = -10V, VIN = "ON" - 2 -200 - -10 -200 nA IINL All VIN = 0V -250 -250 -250 -250 -250 -250 A IINH All VIN = 5V - 10 20 - 10 20 A 30 Switches See Switching Time Test Circuit - 150 - - 180 - ns IS(OFF) ID(OFF) ID(ON) + IS(ON) INPUT DYNAMIC tON 75 Switches tOFF 30 and 75 Switches CS(OFF) DG181, DG182, DG184, DG185, DG187, DG188, DG190, DG191 CD(ON) + CS(ON) OFF Isolation - 250 - - 300 - ns - 130 - - 150 - ns VS = -5V, ID = 0, f = 1MHz 9 Typical pF VD = +5V, IS = 0, f = 1MHz 6 Typical pF VD = VS = 0, f = 1MHz 14 Typical pF Typically >50dB at 10MHz - RL = 75, CL = 3pF 4 DG181 Series Electrical Specifications DEVICE NUMBER V+ = +15V, V- = -15V, VL = 5V, Unless Otherwise Specified (Continued) (NOTE 1) TEST CONDITIONS A SERIES B SERIES -55oC +25oC +125oC -20oC +25oC +85oC UNITS - 1.5 - - 1.5 - mA DG184, DG185 - 0.1 - - 0.1 - mA DG187, DG188 - 0.8 - - 0.8 - mA DG181, DG182, DG190, DG191 - -5.0 - - -5.0 - mA DG184, DG185 - -4.0 - - -4.0 - mA DG187, DG188 - -3.0 - - -3.0 - mA DG181, DG182, DG184, DG185, DG190, DG191 - 4.5 - - 4.5 - mA DG187, DG188 - 3.2 - - 3.2 - mA PARAMETER SUPPLY I+ I- IL DG181, DG182, DG190, DG191 IGND All I+ DG181, DG182, DG190, DG191 I- IL IGND VIN = 5V - -2.0 - - -2.0 - mA - 1.5 - - 1.5 - mA DG184, DG185 - 3.0 - - 3.0 - mA DG187, DG188 - 0.8 - - 0.8 - mA DG181, DG182, DG190, DG191 - -5.0 - - -5.0 - mA DG184, DG185 - -5.5 - - -5.5 - mA DG187, DG188 - -3.0 - - -3.0 - mA DG181, DG182, DG184, DG185, DG190, DG191 - 4.5 - - 4.5 - mA DG187, DG188 - 3.2 - - 3.2 - mA All - -2.0 - - -2.0 - mA +85oC UNITS VIN = 0V NOTE: 1. See Switching State Diagrams for VIN "ON" and VIN "OFF" Test Conditions. Electrical Specifications DEVICE NUMBER Maximum Resistances (RDS(ON) MAX) TEST CONDITIONS (NOTE 1) V+ = 15V, V- = -15V, VL = 5V MILITARY TEMPERATURE -55oC +25oC INDUSTRIAL TEMPERATURE +125oC -20oC +25oC DG181 VD = -7.5V 30 30 60 50 50 75 DG182 VD = -10V 75 75 100 100 100 150 DG184 VD = -7.5V 30 30 60 50 50 75 IS = -10mA, VIN = "ON" DG185 VD = -10V 75 75 150 100 100 150 DG187 VD = -7.5V 30 30 60 50 50 75 DG188 VD = -10V 75 75 150 100 100 150 DG190 VD = -7.5V 30 30 60 50 50 75 DG191 VD = -10V 75 75 150 100 100 150 NOTES: 1. See Switching State Diagrams for VIN "ON" and VIN "OFF" Test Conditions. 2. Normally the minimum signal handling capability of the DG181 thru DG191 family is 20V peak to peak for the 75 switches and 15V peakto-peak for the 30 (refer ID and IS tests above). 3. For other Analog Signals, the following guidelines can be used: proper switch turn-off requires that V- VANALOG(peak) - VP where VP = 7.5V for the 80 switches and VP = 5.0V for 75 switches e.g., - 10V minimum (-peak) analog signal and a 75 switch (VP = 5V), requires that V- -10V -5V = -15V. 5 DG181 Series DUAL DPST - DG184/185 DUAL SPST - DG181/182 TEST CONDITIONS TEST CONDITIONS VIN "ON" = 0.8V All Channels VIN "ON" = 2.0V All Channels VIN "OFF" = 2.0V All Channels VIN "OFF" = 0.8V All Channels NOTE: NOTE: 1. Switch states are for logic "1" input = 2.0V. 1. Switch states are for logic "1" input = 2.0V. SPDT - DG190/191 SPDT - DG187/188 TEST CONDITIONS TEST CONDITIONS VIN "ON" = 2.0V Channel 1 VIN "ON" = 2.0V Channel 1 and 2 VIN "ON" = 0.8V Channel 2 VIN "ON" = 0.8V Channel 3 and 4 VIN "OFF" = 2.0V Channel 2 VIN "OFF" = 2.0V Channel 3 and 4 VIN "OFF" = 0.8V Channel 1 VIN "OFF" = 0.8V Channel 1 and 2 NOTE: NOTE: 1. Switch states are for logic "1" input = 2.0V. 1. Switch states are for logic "1" input = 2.0V. Switching Time Test Circuits +5V VL LOGIC 3V INPUT tR < 10ns tF < 10ns SWITCH INPUT 50% 50% 0V tON, VS = +10V tOFF, VS = -10V LOGIC INPUT SWITCH V INPUT S S1 IN1 GND t ON D1 SWITCH OUTPUT VO RL 1k CL 30pF 90% 90% SWITCH 0V OUTPUT +15V VCC t OFF 0V V-15V (REPEAT TEST FOR ALL CHANNELS) VO = VS FIGURE 1. SWITCHING TIME TEST WAVEFORMS (Note 1) RL RL + RDS(ON) FIGURE 2. SWITCHING TIME TEST CIRCUIT (Note 2) NOTES: 1. Switch output waveform shown for VS = constant with logic input waveform as shown. 2. VS may be + or - as per switching time test circuit. VO is the steady state output with switch on. Feedthrough via gate capacitance may result in spikes at leading and trailing edge of output waveform. 6 DG181 Series Ceramic Dual-In-Line Metal Seal Packages (SBDIP) -A- D14.3 MIL-STD-1835 CDIP2-T14 (D-1, CONFIGURATION C) LEAD FINISH c1 14 LEAD CERAMIC DUAL-IN-LINE METAL SEAL PACKAGE -DBASE METAL E b1 M (b) M -Bbbb S C A - B S INCHES (c) SECTION A-A D S D BASE PLANE S2 Q -C- SEATING PLANE A L S1 eA A A b2 b e ccc M C A - B S D S eA/2 c aaa M C A - B S D S SYMBOL MIN MAX MIN MAX NOTES A - 0.200 - 5.08 - b 0.014 0.026 0.36 0.66 2 b1 0.014 0.023 0.36 0.58 3 b2 0.045 0.065 1.14 1.65 - b3 0.023 0.045 0.58 1.14 4 c 0.008 0.018 0.20 0.46 2 c1 0.008 0.015 0.20 0.38 3 D - 0.785 - 19.94 - E 0.220 0.310 5.59 7.87 - e 0.100 BSC 2.54 BSC - eA 0.300 BSC 7.62 BSC - eA/2 NOTES: 1. Index area: A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded area shown. The manufacturer's identification shall not be used as a pin one identification mark. MILLIMETERS 0.150 BSC 3.81 BSC - L 0.125 0.200 3.18 5.08 - Q 0.015 0.060 0.38 1.52 5 S1 0.005 - 0.13 - 6 S2 0.005 - 0.13 - 7 90o 105o 90o 105o - aaa - 0.015 - 0.38 - 3. Dimensions b1 and c1 apply to lead base metal only. Dimension M applies to lead plating and finish thickness. bbb - 0.030 - 0.76 - ccc - 0.010 - 0.25 - 4. Corner leads (1, N, N/2, and N/2+1) may be configured with a partial lead paddle. For this configuration dimension b3 replaces dimension b2. M - 0.0015 - 0.038 2 2. The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied. N 14 14 8 Rev. 0 4/94 5. Dimension Q shall be measured from the seating plane to the base plane. 6. Measure dimension S1 at all four corners. 7. Measure dimension S2 from the top of the ceramic body to the nearest metallization or lead. 8. N is the maximum number of terminal positions. 9. Braze fillets shall be concave. 10. Dimensioning and tolerancing per ANSI Y14.5M - 1982. 11. Controlling dimension: INCH. 7 DG181 Series Ceramic Dual-In-Line Metal Seal Packages (SBDIP) -A- D16.3 MIL-STD-1835 CDIP2-T16 (D-2, CONFIGURATION C) LEAD FINISH c1 16 LEAD CERAMIC DUAL-IN-LINE METAL SEAL PACKAGE -DBASE METAL E b1 M (b) M -Bbbb S C A - B S INCHES (c) SECTION A-A D S D BASE PLANE S2 Q -C- SEATING PLANE A L S1 eA A A b2 b e ccc M C A - B S D S eA/2 c aaa M C A - B S D S SYMBOL MIN MAX MIN MAX NOTES A - 0.200 - 5.08 - b 0.014 0.026 0.36 0.66 2 b1 0.014 0.023 0.36 0.58 3 b2 0.045 0.065 1.14 1.65 - b3 0.023 0.045 0.58 1.14 4 c 0.008 0.018 0.20 0.46 2 c1 0.008 0.015 0.20 0.38 3 D - 0.840 - 21.34 - E 0.220 0.310 5.59 7.87 - e 0.100 BSC 2.54 BSC - eA 0.300 BSC 7.62 BSC - eA/2 NOTES: 1. Index area: A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded area shown. The manufacturer's identification shall not be used as a pin one identification mark. MILLIMETERS 0.150 BSC 3.81 BSC - L 0.125 0.200 3.18 5.08 - Q 0.015 0.060 0.38 1.52 5 S1 0.005 - 0.13 - 6 S2 0.005 - 0.13 - 7 90o 105o 90o 105o - aaa - 0.015 - 0.38 - 3. Dimensions b1 and c1 apply to lead base metal only. Dimension M applies to lead plating and finish thickness. bbb - 0.030 - 0.76 - ccc - 0.010 - 0.25 - 4. Corner leads (1, N, N/2, and N/2+1) may be configured with a partial lead paddle. For this configuration dimension b3 replaces dimension b2. M - 0.0015 - 0.038 2 2. The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied. N 16 16 8 Rev. 0 4/94 5. Dimension Q shall be measured from the seating plane to the base plane. 6. Measure dimension S1 at all four corners. 7. Measure dimension S2 from the top of the ceramic body to the nearest metallization or lead. 8. N is the maximum number of terminal positions. 9. Braze fillets shall be concave. 10. Dimensioning and tolerancing per ANSI Y14.5M - 1982. 11. Controlling dimension: INCH. 8 DG181 Series Metal Can Packages (Can) T10.B MIL-STD-1835 MACY1-X10 (A2) REFERENCE PLANE A 10 LEAD METAL CAN PACKAGE e1 L L2 L1 INCHES OD2 A A k1 Oe OD OD1 2 N 1 Ob1 Ob F k C L BASE AND SEATING PLANE Q BASE METAL Ob1 LEAD FINISH Ob2 SECTION A-A NOTES: 1. (All leads) Ob applies between L1 and L2. Ob1 applies between L2 and 0.500 from the reference plane. Diameter is uncontrolled in L1 and beyond 0.500 from the reference plane. 2. Measured from maximum diameter of the product. MILLIMETERS SYMBOL MIN MAX MIN MAX NOTES A 0.165 0.185 4.19 4.70 - Ob 0.016 0.019 0.41 0.48 1 Ob1 0.016 0.021 0.41 0.53 1 Ob2 0.016 0.024 0.41 0.61 - OD 0.335 0.375 8.51 9.52 - OD1 0.305 0.335 7.75 8.51 - OD2 0.110 0.160 2.79 4.06 - e 0.230 BSC 5.84 BSC - e1 0.115 BSC 2.92 BSC - F - 0.040 - 1.02 - k 0.027 0.034 0.69 0.86 - k1 0.027 0.045 0.69 1.14 2 L 0.500 0.750 12.70 19.05 1 L1 - 0.050 - 1.27 1 L2 0.250 - 6.35 - 1 Q 0.010 0.045 0.25 1.14 - 36o BSC 36o BSC 3 36o BSC 36o BSC 3 N 10 10 4 Rev. 0 5/18/94 3. is the basic spacing from the centerline of the tab to terminal 1 and is the basic spacing of each lead or lead position (N -1 places) from , looking at the bottom of the package. 4. N is the maximum number of terminal positions. 5. Dimensioning and tolerancing per ANSI Y14.5M - 1982. 6. Controlling dimension: INCH. 9