GS74116AGP/X TSOP, FP-BGA Commercial Temp Industrial Temp 8, 10, 12 ns 3.3 V VDD Center VDD and VSS 256K x 16 4Mb Asynchronous SRAM Features FP-BGA 256K x 16 Bump Configuration (Package X) * Fast access time: 8, 10, 12 ns * CMOS low power operation: 130/105/95 mA at minimum cycle time * Single 3.3 V power supply * All inputs and outputs are TTL-compatible * Byte control * Fully static operation * Industrial Temperature Option: -40 to 85C * Package line up GP: RoHS-compliant 400 mil, 44-pin TSOP Type II package X: 6 mm x 10 mm Fine Pitch Ball Grid Array package GX: RoHS-compliant 6 mm x 10 mm Fine Pitch Ball Grid Array package * RoHS-compliant TSOP-II, and FP-BGA packages available 1 2 3 4 5 6 A LB OE A0 A1 A2 NC B DQ16 UB A3 A4 CE DQ1 C DQ14 DQ15 A5 A6 DQ2 DQ3 D VSS DQ13 A17 A7 DQ4 VDD E VDD DQ12 NC A16 DQ5 VSS F DQ11 DQ10 A8 A9 DQ7 DQ6 G DQ9 NC A10 A11 WE DQ8 H NC A12 A13 A14 A15 NC Description The GS74116A is a high speed CMOS Static RAM organized as 262,144 words by 16 bits. Static design eliminates the need for external clocks or timing strobes. The GS operates on a single 3.3 V power supply and all inputs and outputs are TTLcompatible. The GS74116A is available in a 6 x 10 mm Fine Pitch BGA package and 400 mil TSOP Type-II packages. Description A0-A17 Address input DQ1-DQ16 Data input/output CE Chip enable input LB Lower byte enable input (DQ1 to DQ8) UB Upper byte enable input (DQ9 to DQ16) WE Write enable input OE Output enable input VDD +3.3 V power supply VSS Ground NC No connect Rev: 1.10 1/2013 TSOP-II 256K x 16 Pin Configuration (Package GP) A4 A3 A2 A1 A0 CE DQ1 DQ2 DQ3 DQ4 VDD Pin Descriptions Symbol 6 x 10 mm Substrate Top View VSS DQ5 DQ6 DQ7 DQ8 WE A15 A14 A13 A12 A16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Top view 44 pin TSOP II 16 17 18 19 20 21 22 1/13 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 A5 A6 A7 OE UB LB DQ16 DQ15 DQ14 DQ13 VSS VDD DQ12 DQ11 DQ10 DQ9 NC A8 A9 A10 A11 A17 (c) 2001, GSI Technology GS74116AGP/X Block Diagram A0 Address Input Buffer Row Decoder Memory Array Column Decoder A17 CE WE Control OE _____ UB I/O Buffer DQ1 DQ16 Truth Table CE OE WE LB UB DQ1 to DQ8 DQ9 to DQ16 VDD Current H X X X X Not Selected Not Selected ISB1, ISB2 L L Read Read L H Read High Z H L High Z Read L L Write Write L H Write Not Write, High Z H L Not Write, High Z Write L L L X H L L H H X X High Z High Z L X X H H High Z High Z IDD Note: X: "H" or "L" Rev: 1.10 1/2013 2/13 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, GSI Technology GS74116AGP/X Absolute Maximum Ratings Parameter Symbol Rating Unit Supply Voltage VDD -0.5 to +4.6 V Input Voltage VIN -0.5 to VDD +0.5 ( 4.6 V max.) V Output Voltage VOUT -0.5 to VDD +0.5 ( 4.6 V max.) V Allowable power dissipation PD 0.7 W Storage temperature TSTG -55 to 150 oC Note: Permanent device damage may occur if Absolute Maximum Ratings are exceeded. Functional operation shall be restricted to Recommended Operating Conditions. Exposure to higher than recommended voltages for extended periods of time could affect device reliability. Recommended Operating Conditions Parameter Symbol Min Typ Max Unit Supply Voltage for -8/-10/-12 VDD 3.0 3.3 3.6 V Input High Voltage VIH 2.0 -- VDD +0.3 V Input Low Voltage VIL -0.3 -- 0.8 V Ambient Temperature, Commercial Range TAc 0 -- 70 o C Ambient Temperature, Industrial Range TAI -40 -- 85 o C Notes: 1. Input overshoot voltage should be less than VDD +2 V and not exceed 20 ns. 2. Input undershoot voltage should be greater than -2 V and not exceed 20 ns. Capacitance Parameter Symbol Test Condition Max Unit Input Capacitance CIN VIN = 0 V 5 pF Output Capacitance COUT VOUT = 0 V 7 pF Notes: 1. Tested at TA = 25C, f = 1 MHz 2. These parameters are sampled and are not 100% tested. Rev: 1.10 1/2013 3/13 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, GSI Technology GS74116AGP/X DC I/O Pin Characteristics Parameter Symbol Test Conditions Min Max Input Leakage Current IIL VIN = 0 to VDD - 1 uA 1 uA Output Leakage Current ILO Output High Z VOUT = 0 to VDD -1 uA 1 uA Output High Voltage VOH IOH = -4 mA 2.4 -- Output Low Voltage VOL ILO = +4 mA -- 0.4 V Power Supply Currents Parameter Symbol Test Conditions 0 to 70C -40 to 85C Unit 8 ns 10 ns 12 ns 8 ns 10 ns 12 ns IDD CE VIL All other inputs VIH or VIL Min. cycle time IOUT = 0 mA 130 105 90 140 115 100 mA Standby Current ISB1 CE VIH All other inputs VIH or VIL Min. cycle time 30 25 25 40 35 35 mA Standby Current ISB2 CE VDD - 0.2V All other inputs VDD - 0.2 V or 0.2 V Operating Supply Current Rev: 1.10 1/2013 10 4/13 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. 20 mA (c) 2001, GSI Technology GS74116AGP/X AC Test Conditions Output Load 1 Parameter Conditions Input high level VIH = 2.4 V Input low level VIL = 0.4 V 50 Input rise time tr = 1 V/ns VT = 1.4 V Input fall time tf = 1 V/ns Input reference level 1.4 V Output Load 2 Output reference level 1.4 V 3.3 V Output load Fig. 1& 2 DQ Rev: 1.10 1/2013 589 DQ Notes: 1. Include scope and jig capacitance. 2. Test conditions as specified with output loading as shown in Fig. 1 unless otherwise noted. 3. Output load 2 for tLZ, tHZ, tOLZ and tOHZ 5/13 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. 30pF1 5pF1 434 (c) 2001, GSI Technology GS74116AGP/X AC Characteristics Read Cycle Parameter Symbol Read cycle time -8 -10 -12 Unit Min Max Min Max Min Max tRC 8 -- 10 -- 12 -- ns Address access time tAA -- 8 -- 10 -- 12 ns Chip enable access time (CE) tAC -- 8 -- 10 -- 12 ns Byte enable access time (UB, LB) tAB -- 3.5 -- 4 -- 5 ns Output enable to output valid (OE) tOE -- 3.5 -- 4 -- 5 ns Output hold from address change tOH 3 -- 3 -- 3 -- ns Chip enable to output in low Z (CE) tLZ* 3 -- 3 -- 3 -- ns Output enable to output in low Z (OE) tOLZ* 0 -- 0 -- 0 -- ns Byte enable to output in low Z (UB, LB) tBLZ* 0 -- 0 -- 0 -- ns Chip disable to output in High Z (CE) tHZ* -- 4 -- 5 -- 6 ns Output disable to output in High Z (OE) tOHZ* -- 3.5 -- 4 -- 5 ns Byte disable to output in High Z (UB, LB) tBHZ* -- 3.5 -- 4 -- 5 ns * These parameters are sampled and are not 100% tested. Read Cycle 1: CE = OE = VIL, WE = VIH, UB and, or LB = VIL tRC Address tAA tOH Data Out Rev: 1.10 1/2013 Previous Data Data valid 6/13 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, GSI Technology GS74116AGP/X Read Cycle 2: WE = VIH tRC Address tAA CE tAC tHZ tLZ tAB UB, LB tBHZ tBLZ OE tOE Data Out tOHZ Data valid tOLZ High impedance Write Cycle Parameter Symbol Write cycle time -8 -10 -12 Unit Min Max Min Max Min Max tWC 8 -- 10 -- 12 -- ns Address valid to end of write tAW 5.5 -- 7 -- 8 -- ns Chip enable to end of write tCW 5.5 -- 7 -- 8 -- ns Byte enable to end of write tBW 5.5 -- 7 -- 8 -- ns Data set up time tDW 4 -- 4.5 -- 6 -- ns Data hold time tDH 0 -- 0 -- 0 -- ns Write pulse width tWP 5.5 -- 7 -- 8 -- ns Address set up time tAS 0 -- 0 -- 0 -- ns Write recovery time (WE) tWR 0 -- 0 -- 0 -- ns Write recovery time (CE) tWR1 0 -- 0 -- 0 -- ns Output Low Z from end of write tWLZ* 3 -- 3 -- 3 -- ns Write to output in High Z tWHZ* -- 3.5 -- 4 -- 5 ns * These parameters are sampled and are not 100% tested. Rev: 1.10 1/2013 7/13 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, GSI Technology GS74116AGP/X Write Cycle 1: WE control tWC Address tAW tWR OE tCW CE tBW UB, LB tAS tWP WE tDW tDH Data valid Data In tWHZ tWLZ Data Out High impedance Write Cycle 2: CE control tWC Address tAW tWR1 OE tAS tCW CE tBW UB, LB tWP WE tDW Data valid Data In Data Out Rev: 1.10 1/2013 tDH High impedance 8/13 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, GSI Technology GS74116AGP/X Write Cycle 3: UB, LB control tWC Address tAW tWR1 OE tAS tCW CE tBW UB, LB tWP WE tDW Data valid Data In Data Out Rev: 1.10 1/2013 tDH High impedance 9/13 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, GSI Technology GS74116AGP/X 44-Pin, 400 mil TSOP-II D c 22 e B y L L1 A1 A A2 1 A HE 23 E 44 Dimension in inch Dimension in mm Symbol min nom max min nom max Detail A Rev: 1.10 1/2013 Q A -- -- 0.047 -- -- 1.20 A1 0.002 -- -- 0.05 -- -- A2 0.037 0.039 0.041 0.95 1.00 1.05 B 0.01 0.014 0.018 0.25 0.35 0.45 c -- 0.006 -- -- 0.15 -- D 0.721 0.725 0.729 18.31 18.41 18.51 E 0.396 0.400 0.404 10.06 10.16 10.26 e -- 0.031 -- -- 0.80 -- HE 0.455 0.463 0.471 11.56 11.76 11.96 L 0.016 0.020 0.024 0.40 0.50 0.60 L1 -- 0.031 -- -- 0.80 -- y -- -- 0.004 -- -- 0.10 Q 0o -- 5o 0o -- 5o Notes: 1. Dimension D& E do not include interlead flash. 2. Dimension B does not include dambar protrusion/intrusion. 3. Controlling dimension: mm 10/13 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, GSI Technology GS74116AGP/X 6 mm x 10 mm FP-BGA Symbol D E Pin A1 Index Top View A Unit: mm A 1.100.10 A1 0.20~0.30 fb f0.30~0.40 c 0.36(TYP) D 10.00.05 D1 5.25 E 6.00.05 E1 3.75 e 0.75(TYP) aaa 0.10 c A1 Pin A1 Index Side View aaa A B C D E F G H 1 2 3 4 5 6 fb Solder Ball e E1 e D1 Bottom View Rev: 1.10 1/2013 11/13 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, GSI Technology GS74116AGP/X Ordering Information Part Number* Package Access Time Temp. Range GS74116AGP-8 RoHS-compliant 400 mil TSOP-II 8 ns Commercial GS74116AGP-10 RoHS-compliant 400 mil TSOP-II 10 ns Commercial GS74116AGP-12 RoHS-compliant 400 mil TSOP-II 12 ns Commercial GS74116AGP-8I RoHS-compliant 400 mil TSOP-II 8 ns Industrial GS74116AGP-10I RoHS-compliant 400 mil TSOP-II 10 ns Industrial GS74116AGP-12I RoHS-compliant 400 mil TSOP-II 12 ns Industrial GS74116AX-8 Fine Pitch BGA 8 ns Commercial GS74116AX-10 Fine Pitch BGA 10 ns Commercial GS74116AX-12 Fine Pitch BGA 12 ns Commercial GS74116AX-8I Fine Pitch BGA 8 ns Industrial GS74116AX-10I Fine Pitch BGA 10 ns Industrial GS74116AX-12I Fine Pitch BGA 12 ns Industrial GS74116AGX-8 RoHS-compliant Fine Pitch BGA 8 ns Commercial GS74116AGX-10 RoHS-compliant Fine Pitch BGA 10 ns Commercial GS74116AGX-12 RoHS-compliant Fine Pitch BGA 12 ns Commercial GS74116AGX-8I RoHS-compliant Fine Pitch BGA 8 ns Industrial GS74116AGX-10I RoHS-compliant Fine Pitch BGA 10 ns Industrial GS74116AGX-12I RoHS-compliant Fine Pitch BGA 12 ns Industrial Note: Customers requiring delivery in Tape and Reel should add the character "T" to the end of the part number. For example: GS74116AGP-8T Rev: 1.10 1/2013 12/13 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, GSI Technology GS74116AGP/X 4Mb Asynchronous Datasheet Revision History Rev. Code: Old; New 74116A_r1 Types of Changes Format or Content Format/Content Page #/Revisions/Reason * Created new datasheet 74116A_r1; 74116A_r1_01 Content * Added 6 ns and 7 ns speed bins * Updated power numbers * Changed FPBGA package size from 7.2 x 11.65 mm to 6 x 10 mm * Changed package designator from "U" to "X" for FPBGA * Changed D3 on FPBGA pinout to A17 and E3 to NC 74116A_r1_01; 74116A_r1_02 Content * Updated Recommended Operating Conditions on page 4 * Updated Read Cycle and Write Cycle AC Characteristics tables 74116A_r1_02; 74116A_r1_03 Content * Removed 6 ns speed bin from entire document 74116A_r1_03; 74116A_r1_04 Content * Removed 7 ns speed bin from entire document 74116A_r1_04; 74116A_r1_05 Content/Format * Updated format * Added Pb-free information for TSOP 74116A_r1_05; 74116A_r1_06 Content/Format * Added Pb-free information for FP-BGA 74116A_r1_06; 74116A_r1_07 Content * Changed Pb-free references to RoHS-compliant * Added RoHS-compliant SOJ part * Added status to Ordering Information table 74116A_r1_07; 74116A_r1_08 Content * Removed status from Ordering Information table (all parts MP) 74116A_r1_08; 74116A_r1_09 Content * Removed SOJ references (part is EOL) * (Rev1.09a: Changed 6 x 10 mm Ball Pitch reference on page 1 to 6 x 10 mm Substrate) 74116A_r1_09; 74116A_r1_10 Content * Removed TSOP-II 5/6 RoHS-compliant references (part is EOL) Rev: 1.10 1/2013 13/13 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, GSI Technology