Agilent HLMP-40xx, HLMP-08xx T-1 3/4, 2 mm x 5 mm Rectangular Bicolor LED Lamps Data Sheet Features * Two color operation * Three leads with one common cathode * Option of straight or spread leads configuration * Diffused, wide visibility range Description The T-1 3/4 HLMP-40xx and 2 mm by 5 mm rectangular HLMP-08xx are three leaded bicolor light sources designed for a variety of applications where dual state illumination is required in the same package. There are two LED chips, mounted on a central common cathode lead for maximum on-axis viewability. Colors between the two chips can be generated by independently pulse width modulating the LED chips. Selection Guide Package T-1 3/4 Rectangular Part Number HLMP-4000 HLMP-4000#xxx HLMP-4015 HLMP-0800 HLMP-0805 Color Green/HER Green/Yellow Green/HER Green/Yellow Min. Luminous Intensity Iv (mcd) Green Red Yellow 4.2 2.1 4.2 2.1 20.0 20 2.6 2.1 2.6 1.4 IF (mA) 10 10 20 20 20 Part Numbering System HLMP - X X X X # X X X Mechanical Options 002: Tape & Reel, Straight Leads 010: Right Angle Housing, Even Leads Color Options 00: High Efficiency Red (HER) / High Efficiency Green 05/15: Yellow / High Efficiency Green Package Options 40: T-1 3/4 (5 mm) 08: Rectangular Package Dimensions 2.23 (0.088) 1.98 (0.078) 5.08 (0.200) 4.57 (0.180) 5.18 (0.204) 4.93 (0.194) 8.00 (0.315) 7.37 (0.290) 9.19 (0.362) 8.43 (0.332) 25.40 (1.00) MIN. 1.27 (0.050) NOM. 0.89 (0.035) 0.64 (0.025) COMMON CATHODE 0.508 (0.020) SQ. TYP. 5.46 (0.215) 4.98 (0.196) 2.41 (0.095) 2.03 (0.085) 25.40 (1.00) MIN. COMMON CATHODE 0.508 (0.020) SQ. TYP. SIDE VIEW 1.27 (0.050) NOM. 2.54 (0.100) NOM. 1.27 (0.050) NOM. 1.27 (0.050) NOM. 2.54 (0.100) NOM. GREEN ANODE FLAT INDICATES ANODE 6.10 (0.240) 5.59 (0.220) RED OR YELLOW ANODE (SHORT LEAD) RED OR YELLOW ANODE (SHORT LEAD) COMMON CATHODE COMMON CATHODE HLMP-40xx Straight Leads Notes: 1. All dimensions are in millimeters (inches). 2. Epoxy meniscus may extend about 1 mm (0.040") down the leads. 2 HLMP-08xx Straight Leads GREEN ANODE Absolute Maximum Ratings at TA = 25C Parameter HER/Green Yellow/Green Units Peak Forward Current 90 60 mA Average Forward Current[1,2] (Total) 25 20 mA DC Current[2] (Total) 30 20 mA Power Dissipation[3] (Total) 135 135 mW Operating Temperature Range -20 to +100 -20 to +100 C Storage Temperature Range -55 to +100 -55 to +100 C Reverse Voltage (IR = 100 A) 5 5 V Transient Forward Current[4] 500 500 mA 260 for 5 seconds C (10 sec Pulse) Solder Dipping Temperature (1.6 mm (0.063 inch) below seating plane) Notes: 1. See Figure 5 to establish pulsed operating conditions. 2. The combined simultaneous current must not exceed the maximum. 3. The combined simultaneous current must not exceed the maximum. 4. The transient peak current is the maximum non-recurring current that can be applied to the device without damaging the LED die and wirebond. It is not recommended that the device be operated at peak currents beyond the peak forward current listed in the Absolute Maximum Ratings. Electrical/Optical Characteristics at T A = 25C Symbol Parameter High Efficiency Red Min. Typ. Max. Green Min. Typ. Max. Yellow Min. Typ. Max. Units Test Condition PEAK Peak Wavelength 635 568 583 nm 20 mA d Dominant Wavelength[1] 626 570 585 nm 20 mA s Speed of Response 90 260 90 ns C Capacitance 11 18 15 pF VF = 0, f = 1 MHz VF Forward Voltage 1.9 2.6 V 20 mA VR Reverse Voltage V IR = 100 A RJ-PIN Thermal Resistance Junction-toCathode Lead 21/2 Included Angle between half luminous intensity points[2] HLMP-40xx HLMP-08xx V Luminous Efficacy[3] 5 2.6 2.2 5 3.0 2.1 5 210 210 210 C/W 65 100 65 100 65 100 degree 145 595 500 lm/W Notes: 1. The dominant wavelength, d, is derived from the CIE Chromaticity Diagram and represents the single wavelength which defines the color of the device. 2. 1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 3. Radiant intensity, le, in watts steradian, may be found from the equation le = Iv/V, where Iv is the luminous intensity in candelas and V is the luminous efficacy in lumens/watt. 3 1.0 RELATIVE INTENSITY TA = 25 C ORANGE EMERALD GREEN HIGH PERFORMANCE GREEN HIGH EFFICIENCY RED 0.5 YELLOW 0 500 550 600 650 700 750 WAVELENGTH - nm Figure 1. Relative intensity vs. wavelength. HIGH EFFICIENCY RED, ORANGE, YELLOW, AND HIGH PERFORMANCE GREEN, EMERALD GREEN HER, ORANGE, YELLOW, AND HIGH PERFORMANCE GREEN, EMERALD GREEN 1.6 HIGH PERFORMANCE GREEN, EMERALD GREEN 80 HIGH EFFICIENCY RED/ORANGE 60 YELLOW 40 20 0 1.0 0 2.0 3.0 4.0 RELATIVE LUMINOUS INTENSITY (NORMALIZED AT 20 mA) IF - FORWARD CURRENT - mA 100 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 5.0 YELLOW EMERALD GREEN 1.2 1.1 HIGH EFFICIENCY RED/ORANGE 1.0 0.9 HIGH PERFORMANCE GREEN 0.8 0.7 0.6 0.5 0.4 0 10 20 30 40 50 60 70 80 90 IPEAK - PEAK SEGMENT CURRENT - mA Figure 4. Relative efficiency (luminous intensity per unit current) vs. peak LED current. 4 15 20 30 25 Figure 3. Relative luminous intensity vs. DC forward current. RATIO OF MAXIMUM TOLERABLE PEAK CURRENT TO MAXIMUM TOLERABLE DC CURRENT PEAK - RELATIVE EFFICIENCY (NORMALIZED AT 20 mA) HER, ORANGE, YELLOW, HIGH PERFORMANCE GREEN, EMERALD GREEN 1.3 10 IDC - DC CURRENT PER LED - mA IPEAK MAX. IDC MAX. Figure 2. Forward current vs. forward voltage characteristics. 5 0 VF - FORWARD VOLTAGE - V 6 5 4 10 KHz 300 Hz 30 KHz 1 KHz 100 KHz 3 KHz 100 Hz 3 2 1 1.0 10 100 1000 10,000 tP - PULSE DURATION - s Figure 5. Maximum tolerable peak current vs. pulse duration. (IDC Max. as per maximum ratings.) 20 10 0 1.0 30 0.8 40 50 0.6 60 0.4 70 0.2 80 90 10 20 30 40 50 60 70 80 90 100 Figure 6. Relative luminous intensity vs. angular displacement for HLMP-40xx. 20 10 30 40 0 1.0 0.8 50 0.6 60 70 80 90 0.4 0.2 10 20 30 40 50 60 70 80 90 100 Figure 7. Relative luminous intensity vs. angular displacement for HLMP-08xx. Mechanical Option Matrix Mechanical Option Code 002 010 Definition Tape & Reel, straight leads, minimum increment 1300 pcs/bag Right Angle Housing, even leads, minimum increment 500 pcs/bag Note: All categories are established for classification of products. Products may not be available in all categories. Please contact your local Agilent representative for further clarification/information. 5 www.agilent.com/semiconductors For product information and a complete list of distributors, please go to our web site. For technical assistance call: Americas/Canada: +1 (800) 235-0312 or (916) 788-6763 Europe: +49 (0) 6441 92460 China: 10800 650 0017 Hong Kong: (+65) 6756 2394 India, Australia, New Zealand: (+65) 6755 1939 Japan: (+81 3) 3335-8152 (Domestic/International), or 0120-61-1280 (Domestic Only) Korea: (+65) 6755 1989 Singapore, Malaysia, Vietnam, Thailand, Philippines, Indonesia: (+65) 6755 2044 Taiwan: (+65) 6755 1843 Data subject to change. Copyright (c) 2003 Agilent Technologies, Inc. Obsoletes 5988-3775EN May 30, 2003 5988-9672EN