July 2009 Doc ID 6738 Rev 25 1/28
28
LD1085xx
3 A low drop positive voltage regulator adjustable and fixed
Features
■Typical dropout 1.3 V (at 3 A)
■Three terminal adjustable or fixed output
voltage 1.5 V, 1.8 V, 2.5 V, 3.3 V, 5 V, 12 V.
■Automotive grade product: adjustable VOUT
only in TO-220 full pack package
■Guaranteed output current up to 3 A
■Output tolerance ± 1 % at 25°C and ± 2 % in full
temperature range
■Internal power and thermal limit
■Wide operating temperature range -40 °C to
125 °C
■Package available: TO-220, TO-220FP,
DPAK, D2PAK, D2PAK/A
■Pinout compatibility with standard adjustable
VREG
Description
The LD1085xx is a low drop voltage regulator
able to provide up to 3 A of output current.
Dropout is guaranteed at a maximum of 1.2 V at
the maximum output current, decreasing at lower
loads. The LD1085xx is pin to pin compatible with
the older 3-terminal adjustable regulators, but has
better performances in term of drop and output
tolerance.
A 2.85 V output version is suitable for SCSI-2
active termination. Unlike PNP regulators, where
a part of the output current is wasted as quiescent
current, the LD1085xx quiescent current flows
into the load, so increase efficiency. Only a 10 µF
minimum capacitor is need for stability.
The device is supplied in TO-220, TO-220FP,
DPAK, D2PAK and D2PAK/A. On chip trimming
allows the regulator to reach a very tight output
voltage tolerance, within ± 1 % at 25 °C.
The LD1085xx is available as automotive grade in
TO-220FP package only, for the option of
adjustable output voltage whose commercial part
number is shown in the Table 11: Order codes.
This device is qualified according to the
specification AEC-Q100 of the automotive
market, in the temperature range -40 °C to
125 °C, and the statistical tests PAT, SYL, SBL are
performed.
TO-220FP
D2PAK/A
TO-220
D2PAKDPAK
Table 1. Device summary
Part numbers
LD1085XX LD1085XX25
LD1085XX15 LD1085XX33
LD1085XX18 LD1085XX50
www.st.com
Contents LD1085xx
2/28 Doc ID 6738 Rev 25
Contents
1 Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4 Schematic application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
6 Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8 Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
9 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
LD1085xx Diagram
Doc ID 6738 Rev 25 3/28
1 Diagram
Figure 1. Schematic diagram
Pin configuration LD1085xx
4/28 Doc ID 6738 Rev 25
2 Pin configuration
Figure 2. Pin connections (top view)
TO-220FP
D2PAK/A
TO-220
DPAK
D2PAK
LD1085xx Maximum ratings
Doc ID 6738 Rev 25 5/28
3 Maximum ratings
Note: Absolute maximum ratings are those values beyond which damage to the device may occur.
Functional operation under these condition is not implied
Table 2. Absolute maximum ratings
Symbol Parameter Value Unit
VIDC input voltage 30 V
IOOutput current Internally limited mA
PDPower dissipation Internally limited mW
TSTG Storage temperature range -55 to +150 °C
TOP Operating junction temperature range -40 to +125 °C
Table 3. Thermal data
Symbol Parameter TO-220 TO-220FP DPAK D2PAK
D2PAK/A Unit
RthJC Thermal resistance junction-case 3 5 8 3 °C/W
RthJA Thermal resistance junction-ambient 50 60 100 62.5 °C/W
Schematic application LD1085xx
6/28 Doc ID 6738 Rev 25
4 Schematic application
Figure 3. Application circuit
VOVREF 1R2
R1
-------+
⎝⎠
⎛⎞
⋅=
LD1085xx Electrical characteristics
Doc ID 6738 Rev 25 7/28
5 Electrical characteristics
VI = 4.5 V, CI = CO =10 µF, TA = -40 to 125 °C, unless otherwise specified.
Table 4. Electrical characteristics of LD1085#15
Symbol Parameter Test condition Min. Typ. Max. Unit
VOOutput voltage (1) IO = 0 mA, TJ = 25°C 1.485 1.5 1.515 V
IO = 0 to 3 A, VI = 3.1 to 30 V 1.47 1.5 1.53 V
ΔVOLine regulation IO = 0 mA, VI = 3.1 to 18 V, TJ = 25°C 0.2 4 mV
IO = 0 mA, VI = 3.1 to 15 V 0.4 4 mV
ΔVOLoad regulation IO = 0 to 3 A, TJ = 25°C 2 10 mV
IO = 0 to 3 A 4 20 mV
VdDropout voltage IO =3 A 1.3 1.5 V
IqQuiescent current VI ≤ 30 V 5 10 mA
Isc Short circuit current VI - VO = 5 V 3.2 4.5 A
VI - VO = 25 V 0.2 0.5 A
Thermal regulation TA = 25°C, 30ms pulse 0.008 0.04 %/W
SVR Supply voltage rejection f = 120 Hz, CO = 25 µF, IO = 3 A
VI = 7.5 ± 3 V 60 72 dB
eN RMS output noise voltage (%
of VO)TA = 25°C, f =10 Hz to 10 kHz 0.003 %
S Temperature stability 0.5 %
S Long term stability TA = 125°C, 1000Hrs 0.5 %
1. See short-circuit current curve for available output current at fixed dropout.
Electrical characteristics LD1085xx
8/28 Doc ID 6738 Rev 25
VI = 4.8 V, CI = CO =10 µF, TA = -40 to 125 °C, unless otherwise specified.
Table 5. Electrical characteristics of LD1085#18
Symbol Parameter Test condition Min. Typ. Max. Unit
VOOutput voltage (1) IO = 0 mA, TJ = 25°C 1.782 1.8 1.818 V
IO = 0 to 3 A, VI = 3.4 to 30 V 1.764 1.8 1.836 V
ΔVOLine regulation IO = 0 mA, VI = 3.4 to 18 V TJ = 25°C 0.2 4 mV
IO = 0 mA, VI = 3.4 to 15 V 0.4 4 mV
ΔVOLoad regulation IO = 0 to 3 A, TJ = 25°C 2 10 mV
IO = 0 to 3 A 4 20 mV
VdDropout voltage IO = 3 A 1.3 1.5 V
IqQuiescent current VI ≤ 30 V 5 10 mA
Isc Short circuit current VI - VO = 5 V 3.2 4.5 A
VI - VO = 25 V 0.2 0.5 A
Thermal regulation TA = 25°C, 30 ms pulse 0.008 0.04 %/W
SVR Supply voltage rejection f = 120 Hz, CO = 25 µF, IO = 3 A
VI = 7.5 ± 3 V 60 72 dB
eN RMS output noise voltage (% of
VO)TA = 25°C, f =10 Hz to 10 kHz 0.003 %
S Temperature stability 0.5 %
S Long term stability TA = 125°C, 1000 Hrs 0.5 %
1. See short-circuit current curve for available output current at fixed dropout.
LD1085xx Electrical characteristics
Doc ID 6738 Rev 25 9/28
VI = 5.5 V, CI = CO =10 µF, TA = -40 to 125 °C, unless otherwise specified.
Table 6. Electrical characteristics of LD1085#25
Symbol Parameter Test condition Min. Typ. Max. Unit
VOOutput voltage (1) IO = 0 mA, TJ = 25°C 2.475 2.5 2.525 V
IO = 0 to 3 A, VI = 4.1 to 30 V 2.45 2.5 2.55 V
ΔVOLine regulation IO = 0 mA, VI = 4.1 to 18 V, TJ = 25°C 0.2 4 mV
IO = 0 mA, VI = 4.1 to 18 V 0.4 4 mV
ΔVOLoad regulation IO = 0 to 3 A, TJ = 25°C 2 10 mV
IO = 0 to 3 A 4 20 mV
VdDropout voltage IO = 3 A 1.3 1.5 V
IqQuiescent current VI ≤ 30 V 5 10 mA
Isc Short circuit current VI - VO = 5 V 3.2 4.5 A
VI - VO = 25 V 0.2 0.5 A
Thermal regulation TA = 25°C, 30ms pulse 0.008 0.04 %/W
SVR Supply voltage rejection f = 120 Hz, CO = 25µF, IO = 3 A
VI = 7.5 ± 3 V 60 72 dB
eN RMS output noise voltage (%
of VO)TA = 25°C, f =10 Hz to 10 kHz 0.003 %
S Temperature stability 0.5 %
S Long term stability TA = 125°C, 1000 Hrs 0.5 %
1. See short-circuit current curve for available output current at fixed dropout.
Electrical characteristics LD1085xx
10/28 Doc ID 6738 Rev 25
VI = 6.3 V, CI = CO =10 µF, TA = -40 to 125 °C, unless otherwise specified.
Table 7. Electrical characteristics of LD1085#33
Symbol Parameter Test condition Min. Typ. Max. Unit
VOOutput voltage (1) IO = 0 mA, TJ = 25°C 3.267 3.3 3.333 V
IO = 0 to 3 A, VI = 4.9 to 30 V 3.234 3.35 3.366 V
ΔVOLine regulation IO = 0 mA, VI = 4.9 to 18 V, TJ = 25°C 0.5 6 mV
IO = 0 mA, VI = 4.9 to 18 V 1 6 mV
ΔVOLoad regulation IO = 0 to 3 A, TJ = 25°C 3 15 mV
IO = 0 to 3 A 7 20 mV
VdDropout voltage IO = 3 A 1.3 1.5 V
IqQuiescent current VI ≤ 30 V 5 10 mA
Isc Short circuit current VI - VO = 5 V 3.2 4.5 A
VI - VO = 25 V 0.2 0.5 A
Thermal regulation TA = 25°C, 30 ms pulse 0.008 0.04 %/W
SVR Supply voltage rejection f = 120 Hz, CO = 25 µF, IO = 3 A
VI = 8.3 ± 3 V 60 72 dB
eN RMS output noise voltage (%
of VO)TA = 25°C, f =10 Hz to 10 kHz 0.003 %
S Temperature stability 0.5 %
S Long term stability TA = 125°C, 1000 Hrs 0.5 %
1. See short-circuit current curve for available output current at fixed dropout.
LD1085xx Electrical characteristics
Doc ID 6738 Rev 25 11/28
VI = 8 V, CI = CO =10 µF, TA = -40 to 125 °C, unless otherwise specified.
Table 8. Electrical characteristics of LD1085#50
Symbol Parameter Test condition Min. Typ. Max. Unit
VOOutput voltage (1) IO = 0 mA, TJ = 25°C 4.95 5 5.05 V
IO = 0 to 3 A, VI = 6.6 to 30 V 4.9 5 5.1 V
ΔVOLine regulation IO = 0 mA, VI = 6.6 to 20 V, TJ = 25°C 0.5 10 mV
IO = 0 mA, VI = 6.6 to 20 V 1 10 mV
ΔVOLoad regulation IO = 0 to 3 A, TJ = 25°C 5 10 mV
IO = 0 to 3 A 10 35 mV
VdDropout voltage IO = 3 A 1.3 1.5 V
IqQuiescent current VI ≤ 30 V 5 10 mA
Isc Short circuit current VI - VO = 5 V 3.2 4.5 A
VI - VO = 25 V 0.2 0.5 A
Thermal regulation TA = 25°C, 30 ms pulse 0.008 0.04 %/W
SVR Supply voltage rejection f = 120 Hz, CO = 25 µF, IO = 3 A
VI = 10 ± 3 V 60 72 dB
eN RMS output noise voltage (%
of VO)TA = 25°C, f = 10 Hz to 10 kHz 0.003 %
S Temperature stability 0.5 %
S Long term stability TA = 125°C, 1000 Hrs 0.5 %
1. See short-circuit current curve for available output current at fixed dropout.
Electrical characteristics LD1085xx
12/28 Doc ID 6738 Rev 25
VI = 4.25 V, CI = CO =10 µF, TA = -40 to 125 °C, unless otherwise specified.
Table 9. Electrical characteristics of LD1085#
Symbol Parameter Test condition Min. Typ. Max. Unit
VOOutput voltage (1) IO = 10 mA TJ = 25°C 1.237 1.25 1.263 V
IO = 10 mA to 3 A, VI = 2.85 to 30 V 1.225 1.25 1.275 V
ΔVOLine regulation
IO = 10 mA, VI = 2.85 to 16.5 V,
TJ = 25°C 0.015 0.2 %
IO = 10 mA, VI = 2.85 to 16.5 V 0.035 0.2 %
ΔVOLoad regulation IO = 10 mA to 3 A, TJ = 25°C 0.1 0.3 %
IO = 0 to 3 A 0.2 0.4 %
VdDropout voltage IO = 3 A 1.3 1.5 V
IO(min) Minimum load current VI = 30 V 3 10 mA
Isc Short circuit current VI - VO = 5 V 5.5 6.5 A
VI - VO = 25 V 0.5 0.7 A
Thermal regulation TA = 25°C, 30ms pulse 0.003 0.015 %/W
SVR Supply voltage rejection f = 120 Hz, CO = 25 µF,CADJ = 25 µF,
IO = 3 A, VI = 6.25 ± 3 V 60 72 dB
IADJ Adjust pin current VI = 4.25 V, IO = 10 mA 55 120 µA
ΔIADJ Adjust pin current change (1) IO = 10 mA to 3 A, VI = 2.85 to 16.5 V 0.2 5 µA
eN RMS output noise voltage (%
of VO)TA = 25°C, f =10 Hz to 10 kHz 0.003 %
S Temperature stability 0.5 %
S Long term stability TA = 125°C, 1000 Hrs 0.5 %
1. See short-circuit current curve for available output current at fixed dropout.
LD1085xx Electrical characteristics
Doc ID 6738 Rev 25 13/28
VI = 4.25 V, CI = CO =10 µF, TA = -40 to 125 °C, unless otherwise specified.
Table 10. Electrical characteristics of LD1085PY (Automotive Grade)
Symbol Parameter Test condition Min. Typ. Max. Unit
VOOutput voltage (1) IO = 10 mA TA = 25°C 1.237 1.25 1.263 V
IO = 10 mA to 3 A, VI = 2.85 to 30 V 1.225 1.25 1.275 V
ΔVOLine regulation IO = 10 mA, VI = 2.85 to 16.5 V 0.035 0.2 %
ΔVOLoad regulation IO = 0 to 3 A 0.2 0.4 %
VdDropout voltage IO = 3 A 1.3 1.5 V
IO(min) Minimum load current VI = 30 V 3 10 mA
Isc Short circuit current VI - VO = 5 V, TA = 25°C 5.5 6.5 A
VI - VO = 25 V, TA = 25°C 0.5 0.7 A
Thermal regulation TA = 25°C, 30 ms pulse 0.003 0.015 %/W
SVR Supply voltage rejection f = 120 Hz, CO = 25 µF,CADJ = 25 µF,
IO = 3 A, VI = 6.25 ± 3 V, TA = 25°C 60 72 dB
IADJ Adjust pin current VI = 4.25 V, IO = 10 mA 55 120 µA
ΔIADJ Adjust pin current change (1) IO = 10 mA to 3 A, VI = 2.85 to 16.5 V 0.2 5 µA
eN RMS output noise voltage (%
of VO)TA = 25°C, f =10 Hz to 10 kHz 0.003 %
S Temperature stability 0.5 %
S Long term stability TA = 125°C, 1000 Hrs 0.5 %
1. See short-circuit current curve for available output current at fixed dropout.
Typical application LD1085xx
14/28 Doc ID 6738 Rev 25
6 Typical application
Unless otherwise specified TJ = 25 °C, CI = CO = 10 µF.
Figure 4. Output voltage vs. temperature Figure 5. Output voltage vs. temperature
Figure 6. Output voltage vs. temperature Figure 7. Short circuit current vs. dropout
voltage
Figure 8. Line regulation vs. temperature Figure 9. Load regulation vs. temperature
LD1085xx Typical application
Doc ID 6738 Rev 25 15/28
Figure 10. Dropout voltage vs. temperature Figure 11. Dropout voltage vs. output current
Figure 12. Adjust pin current vs. temperature Figure 13. Quiescent current vs. temperature
Figure 14. Line regulation vs. temperature Figure 15. Supply voltage rejection vs. output
current
Typical application LD1085xx
16/28 Doc ID 6738 Rev 25
Figure 16. Supply voltage rejection vs.
frequency
Figure 17. Supply voltage rejection vs.
temperature
Figure 18. Minimum load current vs.
temperature
Figure 19. Stability, VO = 1.8 V
Figure 20. Stability, VO = 12 V Figure 21. Line transient
VI=12 to 13V, IO=200mA, CI = 1µF(tant), CO=10µF(tant),
CADJ=1µF
LD1085xx Typical application
Doc ID 6738 Rev 25 17/28
Figure 22. Line transient Figure 23. Load transient
VI=12 to 13V, IO=200mA, CI = 1µF(tant), CO=10µF(tant),
CADJ=1µF
VI=12V, IO=0.12 to 3A, CI = 1µF(tant), CO=10µF(tant),
CADJ=1µF
Figure 24. Load transient
VI=12V, IO=0.12 to 3A, CI = 1µF(tant), CO=10µF(tant),
CADJ=1µF
Package mechanical data LD1085xx
18/28 Doc ID 6738 Rev 25
7 Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
LD1085xx Package mechanical data
Doc ID 6738 Rev 25 19/28
Dim. mm. inch.
Min. Typ. Max. Min. Typ. Max.
A 4.40 4.60 0.1730.181
C1.231.32 0.0480.051
D 2.40 2.72 0.094 0.107
D1 1.27 0.050
E0.490.70 0.0190.027
F 0.61 0.88 0.024 0.034
F1 1.14 1.70 0.044 0.067
F2 1.14 1.70 0.044 0.067
G4.95 5.15 0.194 0.203
G1 2.4 2.7 0.094 0.106
H2 10.0 10.40 0.393 0.409
L2 16.4 0.645
L4 13.0 14.0 0.511 0.551
L5 2.65 2.95 0.104 0.116
L6 15.25 15.75 0.600 0.620
L7 6.2 6.6 0.244 0.260
L93.5 3.93 0.137 0.154
DIA. 3.75 3.85 0.147 0.151
TO-220 mechanical data
P011C
Package mechanical data LD1085xx
20/28 Doc ID 6738 Rev 25
Dim. mm. inch.
Min. Typ Max. Min. Typ. Max.
A 4.40 4.60 0.1730.181
B 2.5 2.7 0.098 0.106
D 2.5 2.75 0.098 0.108
E 0.45 0.70 0.017 0.027
F 0.75 1 0.0300.039
F1 1.15 1.50 0.045 0.059
F2 1.15 1.50 0.045 0.059
G4.95 5.2 0.194 0.204
G1 2.4 2.7 0.094 0.106
H 10.0 10.40 0.393 0.409
L2 16 0.630
L328.6 30.6 1.126 1.204
L4 9.810.6 0.3850.417
L5 2.93.6 0.114 0.142
L6 15.916.4 0.626 0.645
L7 99.30.354 0.366
DIA. 33.2 0.1180.126
TO-220FP mechanical data
7012510A-
H
LD1085xx Package mechanical data
Doc ID 6738 Rev 25 21/28
Dim.
mm. inch.
Min. Typ. Max. Min. Typ. Max.
A 2.2 2.4 0.086 0.094
A1 0.91.1 0.035 0.043
A2 0.030.230.001 0.009
B 0.64 0.90.025 0.035
b4 5.2 5.4 0.204 0.212
C 0.45 0.6 0.017 0.023
C2 0.480.6 0.0190.023
D 6 6.2 0.236 0.244
D1 5.1 0.200
E 6.4 6.6 0.252 0.260
E1 4.7 0.185
e2.280.090
e1 4.4 4.6 0.1730.181
H9.35 10.1 0.3680.397
L 1 0.039
(L1) 2.80.110
L2 0.80.031
L4 0.6 1 0.0230.039
R 0.2 0.008
V2 0° 8°0° 8°
DPAK mechanical data
0068772-F
Package mechanical data LD1085xx
22/28 Doc ID 6738 Rev 25
Dim.
mm. inch.
Min. Typ. Max. Min. Typ. Max.
A 4.4 4.6 0.1730.181
A1 2.492.690.098 0.106
A2 0.030.230.001 0.009
B 0.7 0.93 0.027 0.036
B2 1.14 1.7 0.044 0.067
C 0.45 0.6 0.017 0.023
C2 1.231.36 0.0480.053
D8.959.350.352 0.368
D1 80.315
E 10 10.4 0.393 0.409
E1 8.5 0.335
G4.88 5.280.192 0.208
L 15 15.85 0.590 0.624
L2 1.27 1.4 0.050 0.055
L31.4 1.75 0.055 0.068
M2.4 3.2 0.094 0.126
R 0.4 0.016
V2 0° 8°0° 8°
D2PAK mechanical data
P011P6G
LD1085xx Package mechanical data
Doc ID 6738 Rev 25 23/28
Dim.
mm. inch.
Min. Typ. Max. Min. Typ. Max.
A 4.40 4.60 0.1730.181
A1 2.492.690.098 0.106
A2 0.030.230.001 0.009
B 0.7 0.93 0.0280.037
B1 0.81.30.031 0.051
B2 1.14 1.7 0.045 0.067
C 0.45 0.60 0.0180.024
C2 1.231.36 0.0480.054
D8.959.350.352 0.368
D1 80.315
E 10 10.4 0.394 0.409
E1 8.5 0.335
G4.88 5.280.192 0.208
L 15 15.85 0.591 0.624
L2 1.27 1.4 0.050 0.055
M2.4 3.2 0.094 0.126
R 0.4 0.016
V2 0° 8°0° 8°
D2PAK/A mechanical data
7106164/D
Package mechanical data LD1085xx
24/28 Doc ID 6738 Rev 25
Dim.
mm. inch.
Min. Typ. Max. Min. Typ. Max.
A330 12.992
C12.813.0 13.2 0.504 0.512 0.519
D 20.2 0.795
N60 2.362
T22.40.882
Ao 6.806.90 7.00 0.2680.272 0.2.76
Bo 10.40 10.50 10.60 0.4090.4130.417
Ko 2.55 2.65 2.75 0.100 0.104 0.105
Po 3.94.0 4.1 0.1530.157 0.161
P7.98.0 8.1 0.311 0.315 0.319
Tape & reel DPAK-PPAK mechanical data
LD1085xx Package mechanical data
Doc ID 6738 Rev 25 25/28
Dim.
mm. inch.
Min. Typ. Max. Min. Typ. Max.
A180 7.086
C 12.813.0 13.2 0.504 0.512 0.519
D 20.2 0.795
N60 2.362
T 14.4 0.567
Ao 10.50 10.6 10.70 0.4130.417 0.421
Bo 15.70 15.80 15.90 0.6180.622 0.626
Ko 4.80 4.90 5.00 0.189 0.193 0.197
Po 3.94.0 4.1 0.1530.157 0.161
P 11.912.0 12.1 0.4680.472 0.476
Tape & reel D2PAK-P2PAK-D2PAK/A-P2PAK/A mechanical data
Order codes LD1085xx
26/28 Doc ID 6738 Rev 25
8 Order codes
Table 11. Order codes
Packages Output
voltage
TO-220 TO-220FP D2PAK DPAK (T&R) D2PAK/A (T&R)
LD1085DT15R 1.5 V
LD1085D2M18R 1.8 V
LD1085D2M25R 2.5 V
LD1085D2T33R LD1085D2M33R 3.3 V
LD1085V50 5.0 V
LD1085V LD1085P LD1085D2T-R LD1085D2M-R ADJ
LD1085PY (1)
1. Automotive Grade products.
ADJ
LD1085xx Revision history
Doc ID 6738 Rev 25 27/28
9 Revision history
Table 12. Document revision history
Date Revision Changes
07-Oct-2004 12 Mistake order codes - Table 1.
08-Feb-2005 13 Mistake U.M. load regulation - V ==> mV.
01-Mar-2005 14 Version 1.2 V removed.
22-May-2006 15 Order codes has been updated and new template.
10-Nov-2006 16 Add package DPAK, typo on VO test value in tables 3, 4 and 11.
04-Apr-2007 17 Order codes updated.
07-Jun-2007 18 Order codes updated.
05-Dec-2007 19 Modified: Ta ble 1 1.
29-Jan-2008 20 Added new order codes for Automotive grade products see Table 11 on
page 26.
18-Feb-2008 21 Modified: Table 11 on page 26.
09-Apr-2008 22 Modified: Table 11 on page 26.
14-Jul-2008 23 Modified: Table 11 on page 26.
22-Aug-2008 24 Modified: Table 3 on page 5.
28-Jul-2009 25 Modified: Table 11 on page 26.
LD1085xx
28/28 Doc ID 6738 Rev 25
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2009 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
